TECHNICAL DATA

Interface transceiver of RS-232 standard ILX232

with one supply voltage

IC ILX232 is purposed for application in high-performance information processing systems and control
devices of wide application.
Input voltage levels are compatible with standard СMOS levels.

 Output voltage levels are compatible with input levels

of K-MOS, N-MOS and TTL integrated circuits
 Supply voltage : 5V
 Low input current: 1.0 ㎂; 0.1 ㎂ at Т = 25 С
 Output current 24 mA
 Latching current not less than 450 mA at Т = 25С
 Enhanced ESD Specifications:
±15kV IEC61000-4-2 Air Discharge
±8kV IEC61000-4-2 Contact Discharge
IC marking in package
ILX232N Plastic DIP
ILX232D SOIC
ТА= from -40 to 85 оС
For all packages

Pin symbols in package

Truth table C1+ 01 16 VCC

Inputs Outputs V+ 02 15 GND

RIN, TIN ROVT, TOVT C1- 03 14 T1OUT

H L C2+ 04 13 R1IN
ILX232
L H C2- 05 12 R1OUT

V- 06 11 T1IN
Note -
H – voltage high level; T2OUT 07 10 T2IN
L – low voltage level
R2IN 08 09 R2OUT

2015. November. rev.03

 ILX232

Table of pin description

Pin No. Symbol Pin name
01 C1+ Output of external capacitance of positive voltage multiplier unit
02 V+ Output of positive voltage of multiplier unit
03 C1- Output of external capacitance of positive voltage multiplier unit
04 C2+ Output of external capacitance of negative voltage multiplier unit
05 C2- Output of external capacitance of negative voltage multiplier unit
06 V- Output of negative voltage of multiplier unit
07 T2OUT Output of transmitter data (levels RS – 232)
08 R2IN Input of receiver data (levels RS – 232)
09 R2OUT Output of receiver data (levels TTL/KMOS)

10 T2IN Input of transmitter data (levels TTL/KMOS)

11 T1IN Input of transmitter data (levels TTL/KMOS)
12 R1OUT Output of receiver data (levels TTL/KMOS)
13 R1IN Input of receiver data (levels RS – 232)
14 T1OUT Output of transmitter data (levels RS – 232)
15 GND Common output
16 VCC Supply output of voltage source

Maximum conditions
Rate
Symbol Parameter Unit
min max
VCC Supply voltage -0.3 6.0 V
V+ Transmitter high output voltage VCC -0.3 14
V- Transmitter low output voltage -0.3 -14

VTIN Transmitter input voltage -0.3 V+ +0.3

VRIN Receiver input voltage -30 30
Dissipated power
PD DIP – package - 842 mW
SO - package 762
Continu-
ISC Output current of transmitter short circuit - mA
ously
О
Та Ambient temperature -60 150 С
* Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device.
These are stress ratings only and functional operation of the device at these or any other conditions beyond those
indicated under “recommended operating conditions” is not implied.
Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.

2015. November. rev.03

 ILX232

Recommended Operating Conditions

Rate
Symbol Parameter Unit
min max
VCC Supply voltage 4.5 5.5 V
V+ Transmitter output high voltage 5.0 -
V- Transmitter output low voltage -5.0 -
VTIN Transmitter input voltage 0 VСС
VRIN Receiver input voltage -30 30
ISC Transmitter short circuit output current - 60 mA
О
Та Ambient temperature -40 85 С

+
5V +
1.0 F 1.0 F

16
1
+ C1+ 2
1.0 F V+
C1-
3 6
+
4 C2+ V-
1.0 F 1.0 F
C2- +
5

11 14

TTL/CMOS RS-232
Intput
10 7 Output

12 13

TTL/CMOS 5к RS-232
Output Input
9 8

5к
15

2015. November. rev.03

 ILX232

Static parameters
Symbol Parameter Test conditions Unit
Rate

25C -40 C to 85 C
min max min max
ICC Consumption current VCC =5.0 V - 10.0 -  mA
14.0
static VIL = 0 V
Receiver electrical parameters
Vh Hysteresis voltage VCC =5.0 V 0.2 0.9 0.2 1.0 V

V On On (operation) voltage VO  0.1 V - 2.4 - 2.3

IOL  20 uA

Voff Off (dropout) voltage VO  VCC -0.1 V 0.8 - 0.9 -

IOH  -20 uA
VOL Output low voltage IOL = 3.2 mА - 0.3 - 0.4
VСС = 4.5 V
VIH = 2.4 V
VOH Output high voltage IOH = -1.0 mA 3.6 - 3.5 -
VСС = 4.5 V
VIL = 0.8 V
RI Input resistance VСС = 5.0 V 3.0 7.0 3.0 7.0 kOhm

Transmitter electrical parameters

VOL Output low voltage VСС = 4.5 V - -5.2 - -5.0 V
VIH = 2.0 V
RL = 3.0 kOhm
VOH Output high voltage VСС = 4.5 V 5.2 - 5.0 -
VIL = 0.8 V
RL = 3.0 kOhm
IIL Input low current VСС =5.5 V - -1.0 - -10.0 uA
VIL = 0 V

IIH Input high current VСС =5.5 V 1.0 10.0

VIH = VСС
SR Speed of output front VСС =5.0 V 3.0 30 2.7 27 V/㎲
change СL =50 - 1000 pF
RL = 3.0 - 7.0 kOhm
RО Output resistance VСС = V+ = V- = 0 V 350 - 300 - Ohm
VO =  2 V
ISC Short circuit output VСС =5.5 V mA
current VO = 0 V
VI = VСС -50 -60
VI = 0 V 50 60
ST Speed of information VСС =4.5 V 140 - 120 - kbps
transmission СL = 1000 pF
RL = 3.0 kOhm
tW = 7us (for extreme
-tW = 8us)

Dynamic parameters

2015. November. rev.03

 ILX232

Symbol Parameter Test conditions Unit

Rate

25 C from -40 C
to 85 C
min max min max

tPHLR Signal propagation delay time VСС = 4.5 V - 9.7 - 10 us

(tPLHR) when switching on (off) СL = 150 pF
VIL = 0 V
VIH = 3.0 V
tLH = tHL  10 ns
 
tPHLT Signal propagation delay time VСС = 4.5 V 5.0 6.0
(tPLHT) when switching on (off) СL = 2500 pF
VIL = 0 V
VIH = 3.0 V
RL = 3 kOhm
tLH = tHL  10 ns

Capacitance
Symbol Parameter Unit
VCC, Rate

CIN Input capacitance 5.0 9.0 pF

CPD Dynamic capacitance 90

Timing diagram when measuring IC dynamic parameters

+3 V

Rin 1.5 V 1.5 V

0V

VOH

0.5Vcc 0.5Vcc
Rout
VOL
t PHLR t PLHR

Figure 3

2015. November. rev.03

 ILX232

+3 V

Tin
1.5 V 1.5 V

0V

VOH

1.5 V 1.5 V
Tout
VOL
t PHLT tPLHT

Figure 4

Tin

t SLH t SHL

+3 V +3 V

Tout
-3 V -3 V

Figure 5

tW tW

TIN
tW tW

TOUT

Control
strobe

Figure 6

2015. November. rev.03

 ILX232

N SUFFIX PLASTIC DIP

(MS - 001BB)

A
Dimension, mm
16 9
Symbol MIN MAX
B
A 18.67 19.69
1 8
B 6.1 7.11
C 5.33

F L D 0.36 0.56
F 1.14 1.78
C G 2.54
-T- SEATING
PLANE
N
H 7.62

G K
M J J 0 10
D H
K 2.92 3.81
0.25 (0.010) M T
L 7.62 8.26
NOTES:
M 0.2 0.36
1. Dimensions “A”, “B” do not include mold flash or protrusions.
N 0.38
Maximum mold flash or protrusions 0.25 mm (0.010) per side.

D SUFFIX SOIC
(MS - 012AC)

Dimension, mm
A
16 9 Symbol MIN MAX
A 9.8 10
H B P B 3.8 4
C 1.35 1.75
1 G 8 D 0.33 0.51
C R x 45 F 0.4 1.27

-T- G 1.27
SEATING
PLANE
D
K M H 5.72
J F
0.25 (0.010) M T C M J 0 8
K 0.1 0.25
NOTES:
M 0.19 0.25
1. Dimensions A and B do not include mold flash or protrusion.
P 5.8 6.2
2. Maximum mold flash or protrusion 0.15 mm (0.006) per side
for A; for B ‑ 0.25 mm (0.010) per side. R 0.25 0.5

2015. November. rev.03