Professional Documents
Culture Documents
EVIDSurfaceMountS Series-Xmodels F01U345358 en
EVIDSurfaceMountS Series-Xmodels F01U345358 en
EVID-S5.2XB | EVID-S5.2XW
en | Installation manual
en 3
Table of contents
1 Safety 4
1.1 Suspension 4
1.2 Notices 4
2 Introduction 5
2.1 System features 5
2.2 Product information 5
2.3 Packing list 6
3 Installation and wiring 7
3.1 Installing the speaker 7
3.2 U-Bracket installation options 8
3.3 Wiring 9
3.4 Transformer taps 10
3.5 Replacing the logo 11
4 Troubleshooting 12
5 Technical data 13
5.1 Dimensions 14
5.2 Frequency response and impedance 14
1 Safety
1.1 Suspension
Warning!
Suspending any object is potentially dangerous and should only be attempted by individuals
who have a thorough knowledge of the techniques and regulations of suspending objects
overhead. Electro-Voice strongly recommends all loudspeakers be suspended taking into
account all current national, federal, state, and local laws and regulations. It is the
responsibility of the installer to ensure all loudspeakers are safely installed in accordance
! with all such requirements. When loudspeakers are suspended, Electro-Voice strongly
recommends the system be inspected at least once per year or as laws and regulations
require. If any sign of weakness or damage is detected, remedial action should be taken
immediately. The user is responsible for making sure the wall, ceiling, or structure is capable
of supporting all objects suspended overhead. Any hardware used to suspend a loudspeaker
not associated with Electro-Voice is the responsibility of others.
1.2 Notices
Old electrical and electronic appliances
Electrical or electronic devices that are no longer serviceable must be collected separately and
sent for environmentally compatible recycling (in accordance with the European Waste
Electrical and Electronic Equipment Directive).
To dispose of old electrical or electronic devices, you should use the return and collection
systems put in place in the country concerned.
Copyright and disclaimer
All rights reserved. No part of this document may be reproduced or transmitted in any form by
any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior
written permission of the publisher. For information on getting permission for reprints and
excerpts, contact Electro-Voice.
The content and illustrations are subject to change without prior notice.
2 Introduction
The EVID-S series, from Electro-Voice, is a line of compact, high-performance, two-way, full-
range surface mount speakers, with excellent wide and uniform coverage, and outstanding
performance. Their design makes these practically invisible for use in background and
foreground music, paging, and sound reinforcement applications, making EVID-S ideal for
indoor and outdoor applications, such as restaurants, bars, patios, retail, fitness clubs,
hospitality, theme parks, leisure venues, and others. With unparalleled ease-of-installation,
sturdy weather resistance, modern and delicate look, and flexible mounting options, the EVID-
S series is the perfect solution for a wide variety of surface mount applications.
The EVID-S5.2X models are IP65 rated, designed to withstand the toughest weather
conditions.
Read through this manual to familiarize yourself with the safety information, features, and
applications before you use these products.
A Grille
D Gland nut
E U-Bracket
Table 2.1: Product information
A D
A 2 Speakers
B 1 Allen wrench
D 2 U-bracket
E 2 Weather covers
H 1 Installation manual
Table 2.2: Components list
Caution!
It is the installer's responsibility to determine and use the proper mounting hardware for
See also
• U-Bracket installation options, page 8
• Wiring, page 9
See also
• Installing the speaker, page 7
3.3 Wiring
Wiring the speaker
The speaker can be wired using either 2-wires, for input only, or 4-wires, for input and parallel
output. Reference the polarity markers on the Euroblock.
To wire the speaker using the weather cover, do the following:
A A
B B
C C
3. Adjust the tap settings, if needed.
4. Mount the speaker, as shown in the installation section.
5. Plug the Euroblock connector into the speaker.
6. Insert the four screws into the weather cover (B).
Loosely tighten the four screws to keep the weather cover in place.
7. Tighten all four screws to secure the weather cover.
Ensure the weather cover is secure.
8. Adjust the wire length.
9. Tighten the gland nut (C).
See also
• Installing the speaker, page 7
+
A
4 Troubleshooting
Problem Possible Causes Action
No Sound Amplifier Connect a known working test speaker to the amplifier outputs. If
there is no sound, check all electronics are on, the signal routing is
correct, the source is active; the volume is turned up, and so on.
Correct/Repair/Replace as necessary. If there is sound, the problem is
in the wiring.
Wiring Verify you have connected the correct wire pairs to the amplifier. Play
something at low level through the amplifier (for example, from a CD
player or tuner). Connect the test speaker in parallel with the
malfunctioning line. If the sound has gone or is very weak, the line has
a short in it (possibly a severe scrape, pinch, or staple puncture). If
the sound level is normal the wire is open (possibly a cut wire or
missed connection). Using the test speaker, move down the line and
test each connection/junction until you find the problem and correct
it. Observe proper polarity.
Verify you have the inputs and outputs connected to the correct wires.
If the subwoofer input panel is not correctly wired, there will be little
or no sound. Observe proper polarity.
Poor Low- Speakers Wired Out- When two speakers are connected out of polarity (out of phase), the
Frequency of-Polarity low frequencies will cancel each other acoustically. Carefully observe
Response the wire markings or tracers on your speaker wires. Verify the
amplifier (+) terminal is connected to the red speaker terminals and
the amplifier (-) terminal is connected to the black speaker terminals.
Improperly Wired Using a test speaker as described above, verify all amplifier and
Subwoofer Panel speaker wires are connected to their proper terminals with the correct
polarity. Reversing just one set of amplifier wires can cut out all bass
output from the subwoofer.
Intermittent Faulty Connection Check all connections at amplifier and speakers to ensure they are
Output such as, clean and tight. If the problem persists, it may be in the amplifier or
Crackling or wiring. See other actions above.
Distortion
Constant Noise Defective Amplifier If the noise is present but no program material is playing, the likely
such as Buzzing, or other Electronic cause is the signal chain in the electronics. Evaluate each component
Hissing, Humming Device as necessary to isolate the problem.
If these suggestions do not solve your problem, contact your nearest Electro-Voice dealer or
Electro-Voice distributor.
5 Technical data
Frequency response (-3 dB): 90 Hz – 20 kHz
Sensitivity: 89 dB2
Low Z: Yes
Nominal impedance: 8 Ω
Packaged quantity: 2
1
Half space (wall mounting).
2
Half space (on wall) averaged 100 Hz – 10 kHz, 1 W.
3
Without U-Bracket.
5.1 Dimensions
180.0 mm
[7.09 in]
169.0 mm
[6.65 in]
255.0 mm
[10.04 in]
148.0 mm
[5.83 in]
193.0 mm
[7.60 in]
Figure 5.1: EVID-S5.2X dimensions