33 Lights

Single Aisle
TECHNICAL TRAINING MANUAL

T1+T2 (CFM 56) (Lvl 2&3)
LIGHTS
This document must be used for training purposes only
Under no circumstances should this document be used as a reference
It will not be updated.
All rights reserved

No part of this manual may be reproduced in any form,
by photostat, microfilm, retrieval system, or any other means,
without the prior written permission of AIRBUS S.A.S.
AIRBUS Environmental Recommendation

Please consider your environmental responsability before printing this document.
Single Aisle TECHNICAL TRAINING MANUAL
LIGHTS
COCKPIT
CKPT Annunciator Light Test & Dimming D/O (3) . . . . . . . . . . . . . . 2
CABIN
Cabin Lights System Description (3) . . . . . . . . . . . . . . . . . . . . . . . . . 12
FAP Cabin Lighting Page (3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
EXTERIOR
Exterior Lights D/O (3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
EMERGENCY LIGHTS
Seat & Floor Mounted EMER Lights SYS D/O (3) . . . . . . . . . . . . . . 34
UAJ09471 - U59T0T0
T1+T2 (CFM 56) (Lvl 2&3) TABLE OF CONTENTS Nov 27, 2009
33 - LIGHTS Page 1
CKPT ANNUNCIATOR LIGHT TEST & DIMMING D/O (3)

SYSTEM DESCRIPTION POWER SUPPLY AND ASSOCIATED C/B
The power supply is composed of:
An ANNunciator LighT test is used for the lighting of all ANN LTs - busbar 103XP (AC1) which supplies transformer 37LP through the
mounted on the panels and instruments in the cockpit. A relay (relative circuit breaker 26LP located on the circuit breaker panel 122VU,
to system) or internal contacts (case of P/BSWs position indication) - busbar 202XP (AC2) which supplies transformer 36LP through the
control the lighting of each ANN LT. Four different busbars: circuit breaker 27LP located on the circuit breaker panel 122VU,
- AC1 supply with 103XP, - busbar 801XP supplies transformer 31LP through the circuit breaker
- AC2 supply with 202XP, 29LP located on the overhead panel 49VU,
- 115 VAC STATic INVerter bus with 901XP, - busbar 801XP supplies transformer 35LP through the circuit breaker
- ESSential supply with 801XP, 29LP and the busbar 901XP supplies emergency through the circuit
supply the ANN LTs with 5 VAC-400 Hz through the transformers. In breaker 28LP located on the circuit breaker panel 122VU,
the case of emergency supply only busbar 901XP is serviceable. - busbar 206PP supplies the ANN LT test relay coils.
TRANSFORMERS COCKPIT ANN LT SWITCH
There are four transformers; each is supplied with 115 V-400 Hz. A switch with 3 positions (DIM, BRT, TEST) is located on the
Each one is connected to a different busbar. overhead control and indicating panel 25VU. The crew uses this switch
They supply: to dim the cockpit annunciator lights or to test their operation.
- 5 VAC-400 Hz for the ANN LTs installed on the overhead panel
and on the instrument panel, ANN LT TEST AND INTERFACE BOARDS
- 6.3 V voltage (full wave rectified) to supply the AUTO LAND, They are located in the avionics compartment in the annunciator light
MASTER WARNING and CAUTION lights and Audio Control test unit 70VU:
Panels (ACPs). - 4 are related to the ANN LTs supplied by the AC1 system,
The secondary winding of each transformer has: - 3 are related to the ANN LTs supplied by the AC2 generation,
UAJ09471 - U59T0T0 - UM33D3000000001
- 7 outputs of 5 VAC each mounted in parallel; each one is protected - 7 are related to the ANN LTs supplied by the ESS generation.
by a delayed action fuse set at 4 A, Each board comprises:
- 2 outputs of 6.3 V each protected by the same type of fuse. - 2 relays supplied by busbar 206PP with 28 VDC through circuit
The primary winding of each transformer has two inputs to get the breaker 30LP located on the rear circuit breaker panel 122VU. These
correct dimming level (DIMmed position). 2 relays are used for the ANN LT tests when the switch 33LP is in
If the 115 V supply is switched over to either input we obtain at the the TEST position,
secondary winding: - 10 relays supplied by the various A/C systems with 28 VDC. They
- the 5 VAC (BRighT position) or 3 VAC (DIM position), supply the ANN LT with 5 VAC whereas the system data are supplied
- the 6.3 VAC (BRT position) or 4.3 VAC (DIM position) for rectified with 28 VDC
voltages.
T1+T2 (CFM 56) (Lvl 2&3) CKPT ANNUNCIATOR LIGHT TEST & DIMMING D/O (3) Nov 27, 2009
33 - LIGHTS Page 2
FOUR-STAGES RELAY
They are located in the relay box 103VU. They are used for the test
of the equipment annunciator lights (high intensity) or of other
annunciator lights (ON - OFF). The busbar 206PP supplies 28 VDC
to the coil of these relays through the circuit breaker 30LP located on
the rear circuit breaker panel 122VU
UAJ09471 - U59T0T0 - UM33D3000000001
33 - LIGHTS Page 3
UAJ09471 - U59T0T0 - UM33D3000000001
SYSTEM DESCRIPTION - TRANSFORMERS ... FOUR-STAGES RELAY
33 - LIGHTS Page 4
This Page Intentionally Left Blank

UAJ09471 - U59T0T0 - UM33D3000000001
33 - LIGHTS Page 5

SYSTEM OPERATION
The cockpit ANN LT SW is mainly used to test all the ANN LTs in the
cockpit or to dim the ANN LTs in night conditions.
ANN LT SW IN BRT POSITION
In this position, the lighting of the ANN LT is activated:
- either if the relative system failed,
- or if there is an action on the relative P/BSW (OFF position).
UAJ09471 - U59T0T0 - UM33D3000000001
33 - LIGHTS Page 6
UAJ09471 - U59T0T0 - UM33D3000000001
SYSTEM OPERATION - ANN LT SW IN BRT POSITION
33 - LIGHTS Page 7

SYSTEM OPERATION (continued)
ANN LT SW IN TEST POSITION
In this position, the bus 206PP activates the internal coil of the
interface board. So cockpit ANN LTs are powered on all cockpit
panels.
UAJ09471 - U59T0T0 - UM33D3000000001
33 - LIGHTS Page 8
UAJ09471 - U59T0T0 - UM33D3000000001
SYSTEM OPERATION - ANN LT SW IN TEST POSITION
33 - LIGHTS Page 9

SYSTEM OPERATION (continued)
ANN LT SW IN DIM POSITION
In this position, four-stages relays are activated and modify the
transformer voltage output in order to dim the brightness of cockpit
ANN LTs. The lighting of the ANN LT is activated:
- either if the relative system failed,
- or if there is an action on the relative P/BSW (OFF position).
UAJ09471 - U59T0T0 - UM33D3000000001
33 - LIGHTS Page 10
UAJ09471 - U59T0T0 - UM33D3000000001
SYSTEM OPERATION - ANN LT SW IN DIM POSITION
33 - LIGHTS Page 11
CABIN LIGHTS SYSTEM DESCRIPTION (3)

GENERAL PASSENGER READING LIGHTS
The cabin lights are controlled through the Cabin Intercommunication The passenger reading lights can be controlled with buttons on the
Data System (CIDS), which includes the Flight Attendant Panel (FAP), Passengers Service Unit (PSU) and through the FAP. The reading lights
two directors (DIRs) one active, one in standby, and Decoder/Encoder are not adjustable because the Light Emitting Diode (LED) light diffusion
Units (DEUs). Some DEUs are used for the light system, they are called angle is sufficient. Reading lights are supplied by the active CIDS DIR
type "A" DEUs. Signals from the FAP are processed by the DIRs to via DEUs A and Passenger Interface and Supply Adapters (PISAs)
control the cabin lights. The DIRs transmit these signals to each DEU. installed in the Passenger Service Units (PSUs). The test of the passenger
reading lights can be done either via the MCDU of from the FAP.
CABIN GENERAL LIGHTS
ATTENDANT WORK LIGHTS
The related DEUs control the cabin fluorescent lamps according to the
selection on the FAP. The FAP controls the DEUs via the CIDS DIRs to The attendant work lights are controlled by buttons in the attendant area
give brightness (BRT) levels which are: 100% BRT, 50% BRT (Dimming or the FAP. The attendant work lights have a LED technology, and are
1), 10% BRT (Dimming 2) or different lighting scenarios with brightness supplied by the active CIDS DIR via DEUs A and stand alone PISAs.
levels between 100% to 5% for their related window and/or ceiling lights. The test of the attendant work lights can be done either via the MCDU
The cabin fluorescent lamps have Advanced Integrated Ballast Units or from the FAP.
(AIBUs). The ballast units receive FAP commands via CIDS DIRs and
DEUs A for brightness level control. This is according to different lighting NOTE: Note: The Mean Time Between Failure (MTBF) of LED reading
scenarios programmed in the Cabin Assignment Module (CAM) flash lights is 100,000 flight hours. Thus, there is no replacement
card. The ballast units are designed to get a continuous dimming from procedure apart from replacing the complete light assembly.
100% to 5% light BRT level. There is one reading light for each passenger Cabin signs must be replaced if three or more LEDs have failed
seat. (de-graded performance).
UAJ09471 - U59T0T0 - UM33D1000000002
If a full failure of the FAP and/or CIDS occurs or cabin

ENTRY LIGHTS decompression occurs, the entrance lighting comes on
automatically to 100% BRT level.
The related DEUs control the entry fluorescent lamps according to the
FAP selection. The FAP controls the DEUs via the CIDS DIRs in order
to give BRT levels (100%, 50% or 10%).
NOTE: If the engines are running and the cockpit door is open, the
CIDS directors signal the DEU of the left forward entry light
to set the intensity to 10%.
T1+T2 (CFM 56) (Lvl 2&3) CABIN LIGHTS SYSTEM DESCRIPTION (3) Nov 27, 2009
33 - LIGHTS Page 12
UAJ09471 - U59T0T0 - UM33D1000000002
GENERAL ... ATTENDANT WORK LIGHTS
T1+T2 (CFM 56) (Lvl 2&3) CABIN LIGHTS SYSTEM DESCRIPTION (3) Nov 27, 2009
33 - LIGHTS Page 13
FAP CABIN LIGHTING PAGE (3)

GENERAL
The Flight Attendant Panel (FAP) is the main user interface with the
Cabin Intercommunication Data System (CIDS). It programs, monitors
and indicates the status of the CIDS and related cabin systems. The
following system pages are available by pressing the FAP system keys
or the respective aircraft symbols on the screen:
- AUDIO page,
- CABIN LIGHTING page,
- DOORS/SLIDES page,
- CABIN TEMPERATURE page,
- WATER/WASTE page.
STANDARD CABIN LIGHTING CONTROL

Select Lights key on the FAP tool bar, to display the CABIN LIGHTING
page. This page shows an aircraft symbol with the ENTRY and CLASS
lighting zones. The ENTRY 1 and/or ENTRY 4 controls and display
keys are used for the selection of FWD and aft entrance areas lighting,
BRighTness (100%), DIMming 1 (50%), and DIM2 (10%). The cutting-up
of the cabin is possible into 1, 2 or 3 independent zones (selection of 1
zone is standard, and optional for 2 and 3 zones) such as FIRST CLASS,
BUSINESS CLASS and TOURIST CLASS. To control these zones,
UAJ09471 - U59T0T0 - UM33P1000000002
controls and displays are available with three levels of lighting, BRT,
DIM1 and DIM2. The Main On/Off key is used to switch ON/OFF cabin
zone and entrance areas lighting with 100% intensity, this function is
only available on ground. The AISLE key is used to switch ON/OFF the
ceiling lighting, and the WinDOw key to switch ON/OFF the windows
lighting. Additional functions are Reading/Light Set (on) and R/L Reset
(off). An automatic DIM of the FWD entrance area is activated if the
cockpit door is opened and the engines are running. In case of cabin
decompression, the passenger compartment lighting automatically
switches to full brightness (100%).
T1+T2 (CFM 56) (Lvl 2&3) FAP CABIN LIGHTING PAGE (3) Nov 27, 2009
33 - LIGHTS Page 14
UAJ09471 - U59T0T0 - UM33P1000000002
GENERAL & STANDARD CABIN LIGHTING CONTROL
33 - LIGHTS Page 15
FAP CABIN LIGHTING PAGE (3)

SCENARIO BASED LIGHTING CONTROL (OPTIONAL)
This function is used for the control of the cabin lighting through
pre-programmed scenarios. The CIDS gives up to 6 pre-programmed
lighting scenarios defined in NIGHT and DAY modes for the entire cabin
and/or per cabin zone. As an example, these scenarios can be used for
the different cabin services (e.g. Wake up, Sleep, Video, Dinner,...) or
flight phases (e.g. Boarding, Take/Off, Landing,...). All these scenarios
are assigned in the Cabin Assignment Module (CAM). The GENERAL
CABIN SETTINGS keys are used for the cabin lighting ON/OFF control
and cabin lighting settings, the selections can be applied to individual
class zones by selecting the class Select key. Continuous dimming for
each cabin zone is possible by using "+" or "-" keys on the FAP CABIN
LIGHTING page. The MAINTenance key is for lavatory light full
brightness.
UAJ09471 - U59T0T0 - UM33P1000000002
33 - LIGHTS Page 16
UAJ09471 - U59T0T0 - UM33P1000000002
SCENARIO BASED LIGHTING CONTROL (OPTIONAL)
33 - LIGHTS Page 17
EXTERIOR LIGHTS D/O (3)

NAVIGATION LIGHTS
The navigation lights have two systems, which operate independently.
Each system is able to supply one set of navigation lights (RH wing-tip,
LH wing-tip and tail cone). An integrated transformer for the wing tips
and an external transformer for the tail cone, are linked to each lamp.
The navigation lights are controlled by a three-position NAVigation &
LOGO switch (OFF/1/2).
- 1: turns on the logo lights and the first set of navigation lights,
- 2: turns on the logo lights and the second set of navigation lights,
- OFF: all lights are off.
NOTE: On the following slide, NAV 1 configuration is selected by

NAV & LOGO switch, set to the 1 position.
UAJ09471 - U59T0T0 - UM33D4000000001
T1+T2 (CFM 56) (Lvl 2&3) EXTERIOR LIGHTS D/O (3) Nov 27, 2009
33 - LIGHTS Page 18
UAJ09471 - U59T0T0 - UM33D4000000001
NAVIGATION LIGHTS
33 - LIGHTS Page 19

LANDING LIGHTS
One landing light underneath each wing can be extended at all A/C speeds.
Each landing light has an independent extension/retraction and lighting
circuit. Each landing light is controlled by a three-position LAND switch
(ON/OFF/RETRACT):
- ON, extends the left (or right) landing light, which comes on
automatically when fully extended,
- OFF, shut off landing light but leaves it extended,
- RETRACT, retracts the landing light and shuts it off.
When the landing lights are extended, the "LAND LT" memo message
is displayed on the EWD.
UAJ09471 - U59T0T0 - UM33D4000000001
33 - LIGHTS Page 20
UAJ09471 - U59T0T0 - UM33D4000000001
LANDING LIGHTS
33 - LIGHTS Page 21

RUNWAY TURN-OFF LIGHTS
Two runway turn-off lights are installed on the NLG.
The RunWaY TURN OFF SW controls the runway turn-off lights:
- ON: Both lights are on, only if the NLG is downlocked,
- OFF: Both lights are off.
UAJ09471 - U59T0T0 - UM33D4000000001
33 - LIGHTS Page 22
UAJ09471 - U59T0T0 - UM33D4000000001
RUNWAY TURN-OFF LIGHTS
33 - LIGHTS Page 23

TAXI AND TAKE-OFF LIGHTS
The taxi and takeoff lights are installed on the NLG, in a fixed position.
The taxi and takeoff lights are controlled by the three position NOSE
selector:
- T.O: taxi and takeoff lights are on if the NLG is downlocked,
- TAXI: taxi light is on if the NLG is downlocked,
UAJ09471 - U59T0T0 - UM33D4000000001
33 - LIGHTS Page 24
UAJ09471 - U59T0T0 - UM33D4000000001
TAXI AND TAKE-OFF LIGHTS
33 - LIGHTS Page 25

LOGO LIGHTS
The logo lights are installed in the upper surface of each Trimmable
Horizontal Stabilizer (THS) to illuminate the company logo on the vertical
stabilizer if the main gear struts are compressed or the flaps are extended
at least 15°. The logo lights are controlled together with the navigation
lights by the NAV & LOGO SW (OFF/1/2):
- 1: turns on the logo lights and the first set of navigation lights,
- 2: turns on the logo lights and the second set of navigation lights,
UAJ09471 - U59T0T0 - UM33D4000000001
33 - LIGHTS Page 26
UAJ09471 - U59T0T0 - UM33D4000000001
LOGO LIGHTS
33 - LIGHTS Page 27

BEACON LIGHTS
Two beacon lights supply high-intensity red flashing light on the top and
at the bottom of the aircraft fuselage. The beacon lights operate alternately
in synchronization with the strobe lights. They are supplied and controlled
through their related Power Supply Unit (PSU), if the BEACON SW
(ON/OFF) is ON.
UAJ09471 - U59T0T0 - UM33D4000000001
33 - LIGHTS Page 28
UAJ09471 - U59T0T0 - UM33D4000000001
BEACON LIGHTS
33 - LIGHTS Page 29

STROBE LIGHTS
Three strobe lights are installed at each wing tip and at tail cone. They
are synchronized and operate alternatively with the beacon lights. They
are supplied and controlled through their related PSU according to the
STROBE switch position (ON/AUTO/OFF):
- ON: the strobe lights flash white,
- AUTO: the strobe lights come on automatically when the main gear
strut is not compressed,
- OFF: the strobe lights are off.
The "STROBE LT OFF " ECAM memo message is displayed if the strobe
lights are set to OFF and aircraft in flight.
NOTE: The Power Supply Unit for the tail cone strobe light is located
in the THS compartment.
UAJ09471 - U59T0T0 - UM33D4000000001
33 - LIGHTS Page 30
UAJ09471 - U59T0T0 - UM33D4000000001
STROBE LIGHTS
33 - LIGHTS Page 31

WING AND ENGINE SCAN LIGHTS
Two wing and engine scan lights are installed: one on each side of the
fuselage. These lights light the leading edge of the wing and the engine
air intake to show if ice is accumulating there. The WING switch
(ON/OFF) controls these lights.
UAJ09471 - U59T0T0 - UM33D4000000001
33 - LIGHTS Page 32
UAJ09471 - U59T0T0 - UM33D4000000001
WING AND ENGINE SCAN LIGHTS
33 - LIGHTS Page 33
SEAT & FLOOR MOUNTED EMER LIGHTS SYS D/O (3)

GENERAL
The emergency lighting system supplies lighting in case of failure of the
main lighting system or during emergency conditions. The Emergency
Power Supply Units (EPSUs) supply all these different lights. The
emergency lights have 6V DC Light Emitting Diodes (LEDs), except for
lavatory auxiliary lights (28V DC LEDs). The external emergency lights
such as over-wing and escape slide use bulbs technology.
ELECTRICAL SUPPLY
The EPSUs are supplied with 28V DC from the ESSential SHEDdable
BUS for operation and 115V AC from the NORMal BUS voltage sensing.
EPSU
The EPSUs supply the following lights:
- exit signs lights,
- cabin emergency lights,
- seat mounted emergency lights and exit location lights,
- wall mounted emergency exit location light,
- wall mounted exit marking sign,
- wall mounted emergency exit,
- wall mounted emergency light,
UAJ09471 - U59T0T0 - UM33D2000000002
- escape slide lights,

- over-wing emergency lights,
- lavatory auxiliary lights,
- and escape hatch-handle lights.
The EPSUs also monitor the correct voltage of the AC and DC buses.
The EPSUs convert 28V DC into 6V DC to operate their associated lights.
An internal 6V DC battery in each EPSU is charged continuously when
the ESS SHED BUS is energized and the system is not activated.
T1+T2 (CFM 56) (Lvl 2&3) SEAT & FLOOR MOUNTED EMER LIGHTS SYS D/O (3) Nov 27, 2009
33 - LIGHTS Page 34
UAJ09471 - U59T0T0 - UM33D2000000002
GENERAL ... EPSU
33 - LIGHTS Page 35
SEAT & FLOOR MOUNTED EMER LIGHTS SYS D/O (3)

The cabin emergency lights, the exit signs, the escape hatch-handle
OPERATION lights and the seat mounted lights come on. The 28V DC/6V DC
converters of the EPSUs supply these loads as long as the 28V DC
The EMERgency EXIT LighT switch on the overhead panel controls the
ESS SHED BUS is available. If the 28V DC SHED ESS BUS voltage
emergency lighting system. The EMER EXIT LT switch has three
falls below 16V, the EPSUs internal batteries continue to supply the
positions: OFF, ARMed and ON. Each of these positions sends a discrete
loads for at least 10 minutes. The batteries are no longer charged.
ground signal to the EPSUs.
OTHER CASES
OFF POSITION
Independently of the switch positions, the integral lights in the
The system is supplied when the busbars 103XP and 801PP are
respective escape slides come on when the passenger/crew doors or
energized. With the EMER EXIT LT switch and the EMER pushbutton
the emergency exit doors are opened with the escape slides armed.
switch on the FAP in the OFF positions, the power supply units
When the emergency exit hatches are open and the slides are released,
control-line OFF is grounded, All lights and signs are off and the
the respective over-wing emergency lights and the integral lights in
battery in each power supply unit is on charge. The EMER EXIT LT
the respective escape slide come on. In the event of excessive cabin
OFF annunciator lights come on.
depressurization, the exit marking signs and the exit location signs
NOTE: Note: The EXIT signs and the emergency escape automatically come on.
hatch-handle lights come on with EMER EXIT LT switch TEST
OFF, when the NO SMOKING switch is in the ON position
or in AUTO position with landing gear extended, or in Each EPSU has a test circuit which tests the condition of the battery unit,
option, when the EXIT switch is in the ON position or in the logic unit and the related loads. If a fault is detected it is reported to
AUTO position with landing gear extended. CIDS. An EPSU SYStem TEST can be triggered from MCDU or CFDS
Emulation on FAP. The EPSU BATtery CAPacity TEST can only be
ARM POSITION
triggered from MCDU. The duration of this test is around 3 hours. An
UAJ09471 - U59T0T0 - UM33D2000000002
In the ARM position the EMER EXIT LT OFF annunciator light goes individual test on each EPSU must be carried out when the tests through
off. When the 115V AC NORM BUS voltage is not available, the MCDU or CFDS Emulation on FAP fail. This isolated test starts when
cabin emergency lighting and the FPEEPMS light come on. The power you push the TEST P/B on the EPSU
is supplied from the 28V DC/6V DC converter in the related EPSU.
When the 28V DC ESS SHED BUS voltage is not available, the
batteries of all EPSUs supply the emergency lighting system for at
least 10 minutes. The batteries are no longer charged.
ON POSITION
In the ON position the emergency lighting system comes on, as if the
EMERgency P/B on the Flight Attendant Panel (FAP) was pushed.
33 - LIGHTS Page 36
UAJ09471 - U59T0T0 - UM33D2000000002
OPERATION & TEST
33 - LIGHTS Page 37
AIRBUS S.A.S.
31707 BLAGNAC cedex, FRANCE
STM
REFERENCE UAJ09471
NOVEMBER 2009
PRINTED IN FRANCE
AIRBUS S.A.S. 2009
ALL RIGHTS RESERVED
AN EADS COMPANY

33 Lights

Uploaded by

Copyright:

Available Formats

33 Lights

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

33 Lights

Uploaded by

Copyright:

Available Formats

Single Aisle

TECHNICAL TRAINING MANUAL

Under no circumstances should this document be used as a reference

It will not be updated.

All rights reserved

AIRBUS Environmental Recommendation

CKPT ANNUNCIATOR LIGHT TEST & DIMMING D/O (3)

SYSTEM DESCRIPTION - TRANSFORMERS ... FOUR-STAGES RELAY

This Page Intentionally Left Blank

CKPT ANNUNCIATOR LIGHT TEST & DIMMING D/O (3)

SYSTEM OPERATION - ANN LT SW IN BRT POSITION

CKPT ANNUNCIATOR LIGHT TEST & DIMMING D/O (3)

SYSTEM OPERATION - ANN LT SW IN TEST POSITION

CKPT ANNUNCIATOR LIGHT TEST & DIMMING D/O (3)

SYSTEM OPERATION - ANN LT SW IN DIM POSITION

CABIN LIGHTS SYSTEM DESCRIPTION (3)

If a full failure of the FAP and/or CIDS occurs or cabin

GENERAL ... ATTENDANT WORK LIGHTS

FAP CABIN LIGHTING PAGE (3)

STANDARD CABIN LIGHTING CONTROL

GENERAL & STANDARD CABIN LIGHTING CONTROL

FAP CABIN LIGHTING PAGE (3)

SCENARIO BASED LIGHTING CONTROL (OPTIONAL)

EXTERIOR LIGHTS D/O (3)

NOTE: On the following slide, NAV 1 configuration is selected by

EXTERIOR LIGHTS D/O (3)

EXTERIOR LIGHTS D/O (3)

RUNWAY TURN-OFF LIGHTS

EXTERIOR LIGHTS D/O (3)

TAXI AND TAKE-OFF LIGHTS

EXTERIOR LIGHTS D/O (3)

EXTERIOR LIGHTS D/O (3)

EXTERIOR LIGHTS D/O (3)

EXTERIOR LIGHTS D/O (3)

WING AND ENGINE SCAN LIGHTS

SEAT & FLOOR MOUNTED EMER LIGHTS SYS D/O (3)

- escape slide lights,

GENERAL ... EPSU

SEAT & FLOOR MOUNTED EMER LIGHTS SYS D/O (3)

OPERATION & TEST

You might also like