EM5203 Series

Current-Limited Power Distribution Switches

General Description  Over Temperature Protection
 Soft Start and Fast turn off
The EM5203 series is an N-channel MOSFET
 Reverse Voltage Protection
high-side power switch without parasitic body
 Enable Active High or Active Low
diode between drain and source. The EM5203AJ-20
 UL Recognized, File No.E468218
provides very low on-resistance as 60m and
 Halogen Free
continuously delivers up to 1.5A output current.
The fault flag output function indicates fault Applications
conditions to the local USB controller. The other
 USB
features include soft start, current limit protection,
 Notebook & Netbook &MB
Power-On-Reset function, and over temperature
protection. The EM5203 series is available in Pin Configuration
SOT23-3, SOT23-5 and DFN1.8X2.0-06 package.
OUT 5 VIN

GND 2
Ordering Information
OC# 3 4 EN / EN#
Part Number Package Remark
SOT23-5
EM5203BJS-02A SOT23-3 0.2A
EM5203AJ-02A SOT23-5 0.2A/Active High
EM5203J-02A SOT23-5 0.2A/Active Low
EM5203AVK6-02A DFN1.8X2.0-06 0.2A/Active High
EM5203VK6-02A DFN1.8X2.0-06 0.2A/Active Low
EM5203AJ-05A SOT23-5 0.5A/Active High
EM5203J-05A SOT23-5 0.5A/Active Low
EM5203AVK6-05A DFN1.8X2.0-06 0.5A/Active High
EM5203VK6-05A DFN1.8X2.0-06 0.5A/Active Low
EM5203AJ-10A SOT23-5 1A/Active High
EM5203J-10A SOT23-5 1A/Active Low Typical Application Circuit
EM5203AJ-15A SOT23-5 1.5A/Active High
EM5203J-15A SOT23-5 1.5A/Active Low

Features VIN VIN OC#

GND VOUT VOUT

 Wide Input Range 2.5V to 5.5V EM5203
 Low MOSFET On Resistance
Enable

 2us Short Protection Response Disable

EN (EN#)

 Low Quiescent(65uA) & Shutdown Current

Note: A low ESR 100uF capacitor between VOUT &
 Deglitched Open-Drain Fault Flag Output GND is recommended.
 Reverse Current Flow blocking
 Power On Reset Function
 Current Limit Protection

2020/03/26
A.4 1
 EM5203 series
Selection table
EN Function Package
Discharge
Part Number Current Soft-Start Time Active Active
Function SOT23-3 SOT23-5 DFN1.8X2.0-06
High Low
EM5203BJS-02A 0.2A Y 0.5ms V
EM5203AJ-02A 0.2A Y 0.5ms V V
EM5203J-02A 0.2A Y 0.5ms V V
EM5203AVK6-02A 0.2A Y 0.5ms V V
EM5203VK6-02A 0.2A Y 0.5ms V V
EM5203AJ-05A 0.5A Y 0.5ms V V
EM5203J-05A 0.5A Y 0.5ms V V
EM5203AVK6-05A 0.5A Y 0.5ms V V
EM5203VK6-05A 0.5A Y 0.5ms V V
EM5203AJ-10A 1A Y 0.5ms V V
EM5203J-10A 1A Y 0.5ms V V
EM5203AJ-15A 1.5A Y 0.5ms V V
EM5203J-15A 1.5A Y 0.5ms V V

Pin Assignment
Pin Pin No. Pin No. Pin No.
Pin Function
Name SOT23-5 SOT23-3 DFN1.8X2.0-06

GND 2 1 1 Ground.
Input Voltage. This is the drain input to the power device that supplies current to
VIN 5 3 2 the output pin. Minimum 1uF low ESR ceramic capacitor is recommended at this
pin.
EN /
4 - 3 Chip Enable Input (Active high for EN, Active low for EN#)
EN#
OC Flag Output. This is an open-drain output and is set low impedance once
OC# 3 - 4
current limit or over temperature protection enabled. No connect is not used.
VOUT 1 2 5, 6 Output Voltage. VOUT is power output pin.

Function Block Diagram

EN / EN# VIN

Current
Power On
Limit
Reset

Charge Control
Oscillator Logic
Pump
VOUT
Thermal
Protection OC#

GND
Deglitch

2020/03/26
A.4 2
 EM5203 series
Absolute Maximum Ratings (Note1)
 VIN ----------------------------------------------------------------------------------------------------- -0.3V to +6.0V
 Other Pins-------------------------------------------------------------------------------------- -0.3V to (VIN+0.3V)
 Power Dissipation, PD @ TA = 25C, SOT23-5 -------------------------------------------------------- 0.4W
 Package Thermal Resistance, θJA, SOT23-5 (Note 2)------------------------------------------- 250C/W
 Junction Temperature-------------------------------------------------------------------------------------- 150C
 Lead Temperature (Soldering, 10 sec.)--------------------------------------------------------------- 260C
 Storage Temperature -------------------------------------------------------------------------- 65C to 150C
 ESD susceptibility (Note3)
HBM (Human Body Mode)-------------------------------------------------------------------------------- 2KV
MM (Machine Mode)--------------------------------------------------------------------------------------- 200V

Recommended Operating Conditions (Note4)

 Supply Input Voltage, VIN --------------------------------------------------------------------- +2.5V to +5.5V
 Junction Temperature -------------------------------------------------------------------------- 40C to 125C
 Ambient Temperature ---------------------------------------------------------------------------- 40C to 85C

2020/03/26
A.4 3
 EM5203 series
Electrical Characteristics
VIN=5V, TA=25℃, unless otherwise specified
Parameter Symbol Test Conditions Min Typ Max Units
Supply Input Section
POR Threshold VPORTH - 2.2 2.5 V
Quiescent Current IQ IOUT=0A - 65 120 uA
Shutdown Current ISD EN#=5V - 0.1 1 uA
Output Voltage
For EM5203BJS-02A 110 140 m
For EM5203AJ/J-02A
85 100 m
For EM5203AVK6/VK6-02A
On Resistance RON
For EM5203AJ/J-05A
85 100 m
For EM5203AVK6/VK6-05A
For EM5203AJ/J-10A/15A 85 100 m
Reverse Leakage Current IRev VOUT=5V , VIN=0V - 0.1 2 uA
Rising from 10% to 90%
Soft-Start Time Tss 0.5 1.5 ms
CL =1uF；RLOAD =10
EN high to Vo 10%, VIN=5V,
Turn On Delay Time Td 200 us
CL =1uF；RLOAD =10
Enable
Enable High Level VEN 1.2 - - V
Disable Low Level VSD - - 0.5 V
EN Input Current IEN - 0.1 1 uA
OC# Flag Output
OC# Output Resistance RFLGB ISINK=1mA - 20 80 
OC# Off Current IFLGB_OFF VFLGB=5V - 0.1 1 uA
OC# Delay Time TD 4 8 20 ms
OUT Shutdown Discharge
RDIS 100 
Resistance
Protection
OCP Threshold Level IOCP 0.3 0.4 0.65 A
EM5203-02
Output Short Circuit Current ISC 0.3 A
OCP Threshold Level IOCP 0.6 0.8 1.2 A
EM5203-05
Output Short Circuit Current ISC 0.5 A
OCP Threshold Level IOCP 1.1 1.3 1.8 A
EM5203-10
Output Short Circuit Current ISC 0.8 A
OCP Threshold Level IOCP 1.6 1.8 2.4 A
EM5203-15
Output Short Circuit Current ISC 1.2 A
o
Thermal Shutdown Temperature TSD - 160 - C
o
Thermal Shutdown Hysteresis TSDHYS - 30 - C

Note 1. Stresses listed as the above “Absolute Maximum Ratings” may cause permanent damage to the device.
These are for stress ratings. Functional operation of the device at these or any other conditions beyond
those indicated in the operational sections of the specifications is not implied. Exposure to absolute
maximum rating conditions for extended periods may remain possibility to affect device reliability.
JA is measured in the natural convection at TA=25 C on a low effective thermal conductivity test board (Single layout,
o
Note 2.
1S) of JEDEC 51-3 thermal measurement standard.
Note 3. Devices are ESD sensitive. Handling precaution is recommended.
Note 4. The device is not guaranteed to function outside its operating conditions.
2020/03/26
A.4 4
 EM5203 series
Typical Operating Characteristics
Turn on from VIN# Turn off from VIN#
CH1: VIN, CH2:Vo, CH3:OC# CH1: VIN, CH2:Vo, CH3:OC#

Reverse Voltage Protection Normal operating 2A output current

CH1:VIN, CH2:Vo, CH3: OC# ,CH4:IREV CH1:Vo, CH2:Fault, CH4:Io

Fault Signal delay time Fault Signal during OTP occurs

CH1:VIN, CH2:VO, CH3:OC#,CH4:Io CH1:Vo, CH2:OC#, CH4:Io

2020/03/26
A.4 5
 EM5203 series
Typical Operating Characteristics
2uS Response for Output short Protection
CH1:VIN, CH2:Vo, CH3:OC#, CH4: IO

RON Performance VS Temperature

EM5203-20 series

UVLO ON Voltage VS Temperature Enable Voltage VS Temperature

2020/03/26
A.4 6
 EM5203 series
Device Code
Ordering & Marking Information XX Part Number
Device Name: EM5203 for SOT23-5 KQ EM5203AJ-02A
KM EM5203AJ-05A
KK EM5203AJ-10A
KP EM5203J-02A
XXYWW XX : Device Code
KN EM5203J-05A
YWW: Date Code
KL EM5203J-10A
NG EM5203J-15A

Outline Drawing

B1 B

e G

A
F

b
A1
Dimension in mm
Dimension A A1 B B1 b C D e F G
Min. 0.9 0 2.6 1.5 0.3 0.08 2.8 0.87 1 0.3
Typ. 1.1 0.04 2.8 1.6 0.4 0.127 2.9 0.95 1.225 0.45
Max. 1.3 0.15 3 1.726 0.5 0.22 3.026 1.03 1.45 0.6
Recommended minimum pads
1.9
1
1.6

3.6

0.95 0.7
2.6

2020/03/26
A.4 7
 EM5203 series
 Tape&Reel Information:3000pcs/Reel(Dimension in millimeter)

2.0±0.05

1.55±0.05

9°MAX

8.0±0.3
PIN1
3.5±0.05

FEED DIRECTION 9°MAX

1.0±0.25
4.0±0.1 1.4 MAX
9.0±0.3

?60±1
ψ
180±1

61

0
16
ψ

11.4±1

Package SOT23-5
Reel Dimensions 7”
Pin1 Orientation

Leader Empty Pockets 50

Trailer Empty Pockets 50
Quantity per Reel 3K
Reel / Inner Box 5：1
Quantity per Inner Box 15K
Inner Box/ Outer 12：1
Carton
Quantity per Outer 180K
Carton

2020/03/26
A.4 8
 EM5203 series

Ordering & Marking Information:

Device Name: EM5203BJS for SOT23-3

KJ: Device Code, KJ for EM5203BJS-02A

ABC: Date Code

Outline Drawing
b
C
L1

A1
E1
E

e
e1
D
A

Dimension in mm
Dimension A A1 b C D E E1 e e1 F G L1
Min. 0.70 0 0.3 0.08 2.80 2.25 1.2 0.90 0.80 0.3 0.50
Typ. 2.90 0.95 1.9
Max. 1.15 0.1 0.5 0.20 3.02 3.00 1.7 1.00 1.25 0.6 0.75

Recommended minimum pads

2020/03/26
A.4 9
 EM5203 series
 Tape&Reel Information:3000pcs/Reel(Dimension in millimeter)

4.0±0.1 2.0±0.1 1.5±0.1

1.75±0.1

3.5±0.1

8.0±0.3

2.77±0.1
4.0±0.1

1.22±0.1
9.5±1

?54.4±1
ψ
51
178±2

.2

6
15
ψ

12.3±1

Package SOT23-3
Reel Dimensions 7”
Pin1 Orientation

Leader Empty Pockets 50

Trailer Empty Pockets 50
Quantity per Reel 3K
Reel / Inner Box 5：1
Quantity per Inner Box 15K
Inner Box/ Outer Carton 12：1
Quantity per Outer 180K
Carton

2020/03/26
A.4 10
 EM5203 series
Ordering & Marking Information:
Device Name: EM5203 for DFN1.8X2.0-06

Device Code
XX Part Number
XX XX : Device Code KV EM5203AVK6-02A

YWW YWW : Date Code KW

KX
EM5203VK6-02A
EM5203AVK6-05A
KY EM5203VK6-05A

Outline Drawing

Dimension in mm
Dimension A A1 A3 b D E D1 E1 e K L
Min. 0.5 0 0.15 1.7 1.9 1.3 0.8 0.174
Typ. 0.55 0.02 0.1 0.25 1.8 2 1.45 0.9 0.5 0.2 0.25
Max. 0.6 0.05 0.35 1.9 2.1 1.6 1.0 0.326

Recommended minimum pads

0.35 0.50
0.46
1.0
2.22

1.65
0.15

0.15

2020/03/26
A.4 11
 EM5203 series
 Tape&Reel Information:3000pcs/Reel(Dimension in millimeter)

2.0±0.05 4.0±0.1
1.50±0.10

8°MAX

8.0±0.3
PIN1
1.75±0.1
3.5±0.05

2.25±0.05
FEED DIRECTION 8°MAX
1.0±0.25
4.0±0.1 1.0±0.05
8.4+2.5

ψ53.6
177.8 MAX

ψ
61

0
16
ψ

14.4

Package DFN1.8X2.0-06
Reel Dimensions 7”
Pin1 Orientation

Leader Empty Pockets 50

Trailer Empty Pockets 50
Quantity per Reel 3K
Reel / Inner Box 5：1
Quantity per Inner Box 15K
Inner Box/ Outer Carton 12：1
Quantity per Outer 180K
Carton

2020/03/26
A.4 12