Þ

èéêêïëíï

Þ
 W270B
Wheel Loader

Bur 87661531

Use for Service Manual

 W270B Wheel Loader
Service Manual
87661531

Table of Contents
Description Section No.
General Tab 1
Section Index - General
Standard Torque Specifications 1001
Fluids and Lubricants 1002
Metric Conversion Chart 1003

Engines Tab 2
Section Index - Engines
Engine and Radiator Removal and Installation 2000
Aftercooler 2003

Fuel System Tab 3

Section Index - Fuel System
For Fuel System Repair, See the Engine Service Manual

Electrical Tab 4
Section Index - Electrical
Removal and Installation of Starter and Alternator 4001
Electrical Specifications and Troubleshooting 4002
Batteries 4003
Instrument Cluster 4005

Copyright © 2007 CNH Italia S.p.A.

CNH Italia S.p.A. All rights reserved.
Viale delle Nazioni, 55
41100 Modena Printed in E.C.
Italia Issued III-2007
 W270B Wheel Loader
Service Manual
87661531

Table of Contents
Description Section No.
Steering Tab 5
Section Index - Steering
Removal and Installation of Steering Components 5001
Steering Specifications, Pressure Checks, and Troubleshooting 5002
Steering Cylinders 5005
Center Pivot 5006
Auxiliary Steering Motor and Pump 5007

Power Train Tab 6

Section Index - Power Train
Removal and Installation of Power Train Components 6001
Transmission Specifications, Pressure Checks, and Troubleshooting 6002
Transmission 6003
Front and Rear Axle 6004
Drive Shafts, Center Bearing, and Universal Joints 6005
Wheels and Tires 6006
Transmission Control Valve 6007

Brakes Tab 7
Section Index - Brakes
Removal and Installation of Brake Components 7001
Hydraulic Brake Troubleshooting 7002
Brake Accumulators 7004
Parking Brake 7008

Hydraulics Tab 8
Section Index - Hydraulics
Removal and Installation of Hydraulic Components 8001
Hydraulic Specifications, Troubleshooting, and Pressure Checks 8002
Cleaning the Hydraulic System 8003
Hydraulic Pump 8004
Loader Control Valve 8005
Cylinders 8006
Pilot Pressure Accumulator and Ride Control Accumulator 8013
Ride Control Valve 8014
 W270B Wheel Loader
Service Manual
87661531

Table of Contents
Description Section No.
Mounted Equipment Tab 9
Section Index - Mounted Equipment
Air Conditioning Troubleshooting and System Checks For Systems with HFC-134a Refrigerant 9002
Air Conditioner System Service 9003
Removal and Installation of Air Conditioning and Heater Components 9004
Loader 9006
ROPS Cab and ROPS Canpoy 9007
Cab Glass Installation 9010

Electrical Schematic Foldouts and Hydraulic Schematic Foldout In Rear Pocket

Copyright © 2007 CNH Italia S.p.A.

CNH Italia S.p.A. All rights reserved.
Viale delle Nazioni, 55
41100 Modena Printed in E.C.
Italia Issued III-2007
 Copyright © 2007 CNH Italia S.p.A.
CNH Italia S.p.A. All rights reserved.
Viale delle Nazioni, 55
41100 Modena Printed in E.C.
Italia Issued III-2007
 SECTION INDEX

GENERAL

Section Title Section Number

Standard Torque Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1001

Fluids and Lubricants . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1002
Metric Conversion Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1003
 Section
1001

GENERAL TORQUE SPECIFICATIONS

Copyright © 2007 CNH Italia S.p.A.

CNH Italia S.p.A. All rights reserved.
Viale delle Nazioni, 55
41100 Modena Printed in E.C.
Italia Issued III-2007
1001-2

TABLE OF CONTENTS
TORQUE SPECIFICATIONS - DECIMAL HARDWARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
TORQUE SPECIFICATIONS - METRIC HARDWARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
TORQUE SPECIFICATIONS - STEEL HYDRAULIC FITTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
TORQUE SPECIFICATIONS - STEEL HYDRAULIC FITTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
 1001-3

TORQUE SPECIFICATIONS - DECIMAL HARDWARE

Use the torques in this chart when special torques
are not given. These torques apply to fasteners with Grade 8 Bolts, Nuts, and Studs
b oth UN C a nd UNF th re ad s as rec eive d fr om
suppliers dry, or when lubricated with engine oil. Not
ap plic able if sp ecial g rap hities , Mo ly disulfid e
greases, or other extreme pressure lubricants are
Pound- Newton
used.
Size Inches metres
1/4 inch 144 to 180 16 to 20
Grade 5 Bolts, Nuts, and Studs
5/16 inch 288 to 348 33 to 39
3/8 inch 540 to 648 61 to 73

Pound- Newton Pound- Newton

Size Inches metres Size Feet metres
1/4 inch 108 to 132 12 to 15 7/16 inch 70 to 84 95 to 114
5/16 inch 204 to 252 23 to 28 1/2 inch 110 to 132 149 to 179
3/8 inch 420 to 504 48 to 57 9/16 inch 160 to 192 217 to 260
5/8 inch 220 to 264 298 to 358
Pound- Newton 3/4 inch 380 to 456 515 to 618
Size Feet metres
7/8 inch 600 to 720 814 to 976
7/16 inch 54 to 64 73 to 87
1.0 inch 900 to 1080 1220 to 1465
1/2 inch 80 to 96 109 to 130
1-1/8 inch 1280 to 1440 1736 to 1953
9/16 inch 110 to 132 149 to 179
1-1/4 inch 1820 to 2000 2468 to 2712
5/8 inch 150 to 180 203 to 244
1-3/8 inch 2380 to 2720 3227 to 3688
3/4 inch 270 to 324 366 to 439
1-1/2 inch 3160 to 3560 4285 to 4827
7/8 inch 400 to 480 542 to 651
NOTE: Use thick nuts with Grade 8 bolts.
1.0 inch 580 to 696 787 to 944
1-1/8 inch 800 to 880 1085 to 1193
1-1/4 inch 1120 to 1240 1519 to 1681
1-3/8 inch 1460 to 1680 1980 to 2278
1-1/2 inch 1940 to 2200 2631 to 2983
1001-4

TORQUE SPECIFICATIONS - METRIC HARDWARE

Use the following torques when specifications are not
given. Grade 10.9 Bolts, Nuts, and Studs
These values apply to fasteners with coarse threads
as received from supplier, plated or unplated, or 10.9
when lubricated with engine oil. These values do not
apply if graphite or Molydisulfide grease or oil is Pound- Newton
used. Size Inches metres
M4 36 to 48 4 to 5
Grade 8.8 Bolts, Nuts, and Studs M5 84 to 96 9 to 11
M6 132 to 156 15 to 18
8.8
M8 324 to 384 37 to 43

Pound- Newton
Size Inches metres Pound- Newton
M4 24 to 36 3 to 4 Size Feet metres

M5 60 to 72 7 to 8 M10 54 to 64 73 to 87

M6 96 to 108 11 to 12 M12 93 to 112 125 to 150

M8 228 to 276 26 to 31 M14 149 to 179 200 to 245

M10 456 to 540 52 to 61 M16 230 to 280 310 to 380

M20 450 to 540 610 to 730

Pound- Newton M24 780 to 940 1050 to 1275

Size Feet metres M30 1470 to 1770 2000 to 2400
M12 66 to 79 90 to 107 M36 2580 to 3090 3500 to 4200
M14 106 to 127 144 to 172
Grade 12.9 Bolts, Nuts, and Studs
M16 160 to 200 217 to 271
M20 320 to 380 434 to 515
12.9
M24 500 to 600 675 to 815
M30 920 to 1100 1250 to 1500
Usually the torque values specified for grade 10.9
M36 1600 to 1950 2175 to 2600 fasteners can be used satisfactorily on grade 12.9
fasteners.
 1001-5

TORQUE SPECIFICATIONS - STEEL HYDRAULIC FITTINGS

Tube OD Thread Pound- Newton Tube OD Thread Pound- Newton
Hose ID Size Inches metres Hose ID Size Inches metres
37 Degree Flare Fitting Straight Threads with O-ring
1/4 inch 7/16-20 72 to 144 8 to 16 1/4 inch 7/16-20 144 to 228 16 to 26
6.4 mm 6.4 mm
5/16 inch 1/2-20 96 to 192 11 to 22 5/16 inch 1/2-20 192 to 300 22 to 34
7.9 mm 7.9 mm
3/8 inch 9/16-18 120 to 300 14 to 34 3/8 inch 9/16-18 300 to 480 34 to 54
9.5 mm 9.5 mm
1/2 inch 3/4-16 180 to 504 20 to 57 1/2 inch 3/4-16 540 to 804 57 to 91
12.7 mm 12.7 mm
5/8 inch 7/8-14 300 to 696 34 to 79
15.9 mm Tube OD Thread Pound- Newton
Hose ID Size Inches metres
Tube OD Thread Pound- Newton 5/8 inch 7/8-14 58 to 92 79 to 124
Hose ID Size Inches metres 15.9 mm
3/4 inch 1-1/16-12 40 to 80 54 to 108 3/4 inch 1-1/16-12 80 to 128 108 to 174
19.0 mm 19.0 mm
7/8 inch 1-3/16-12 60 to 100 81 to 135 7/8 inch 1-3/16-12 100 to 160 136 to 216
22.2 mm 22.2 mm
1.0 inch 1-5/16-12 75 to 117 102 to 158 1.0 inch 1-5/16-12 117 to 187 159 to 253
25.4 mm 25.4 mm
1-1/4 inch 1-5/8-12 125 to 165 169 to 223 1-1/4 inch 1-5/8-12 165 to 264 224 to 357
31.8 mm 31.8 mm
1-1/2 inch 1-7/8-12 210 to 250 285 to 338 1-1/2 inch 1-7/8-12 250 to 400 339 to 542
38.1 mm 38.1 mm

Split Flange Mounting Bolts

Pound- Newton
Size Inches metres
5/16-18 180 to 240 20 to 27
3/8-16 240 to 300 27 to 34
7/16-14 420 to 540 47 to 61

Pound- Newton
Size Feet metres
1/2-13 55 to 65 74 to 88
5/8-11 140 to 150 190 to 203
1001-6

TORQUE SPECIFICATIONS - STEEL HYDRAULIC FITTINGS

Nom.
SAE
Dash Thread Pound- Newton Thread Pound- Newton
Size Tube OD Size Inches metres Size Inches metres
O-ring Boss End
O-ring Face Seal End Fitting or Lock Nut
-4 1/4 inch 9/16-18 120 to 144 14 to 16 7/16-20 204 to 240 23 to 27
6.4 mm
-6 3/8 inch 11/16-16 216 to 240 24 to 27 9/16-18 300 to 360 34 to 41
9.5 mm
-8 1/2 inch 13/16-16 384 to 480 43 to 54 3/4-16 540 to 600 61 to 68
12.7 mm

Thread Pound- Newton

Size Inches metres
-10 5/8 inch 1-14 552 to 672 62 to 76 7/8-14 60 to 65 81 to 88
15.9 mm

Nom. 1-1/16-12 85 to 90 115 to 122

SAE
Dash Thread Pound- Newton 1-3/16-12 95 to 100 129 to 136
Size Tube OD Size Inches metres
-12 3/4 inch 1-3/16-12 65 to 80 90 to 110 1-5/16-12 115 to 125 156 to 169
19.0 mm
-14 7/8 inch 1-3/16-12 65 to 80 90 to 110 1-5/8-12 150 to 160 203 to 217
22.2 mm
-16 1.0 inch 1-7/16-12 92 to 105 125 to 140 1-7/8-12 190 to 200 258 to 271
25.4 mm
-20 1-1/4 inch 1-11/16-12 125 to 140 170 to 190
31.8 mm
-24 1-1/2 inch 2-12 150 to 180 200 to 254
38.1 mm
 Section
1002

FLUIDS AND LUBRICANTS

Copyright © 2007 CNH Italia S.p.A.

CNH Italia S.p.A. All rights reserved.
Viale delle Nazioni, 55
41100 Modena Printed in E.C.
Italia Issued III-2007
1002-2

TABLE OF CONTENTS
CAPACITIES AND LUBRICANTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
ENGINE OIL RECOMMENDATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
HYDRAULIC OIL TEMPERATURE CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
TRANSMISSION OIL TEMPERATURE CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
ENGINE OIL TEMPERATURE CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
DIESEL FUEL SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Fuel Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Specifications for Acceptable No. 2 Diesel Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
MAINTENANCE SCHEDULE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Model W270B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
MAINTENANCE POINTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Model W270B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
 1002-3

CAPACITIES AND LUBRICANTS

Engine Oil
Capacity with Filter Change .............................................................................................37 liters (39 U.S. quarts)
Type of oil........................... AMBRA Mastergold HSP SAE 15W-40, see engine oil recommendations on page 4
Engine Cooling System
Capacity...................................................................................................................56.8 liters (15.0 U.S. Gallons)
Type of Coolant ...................................................................AMBRA Agriflù 50% water and 50% Ethylene Glycol
Fuel Tank
Capacity ................................................................................................................. 393.6 liters (104 U.S. Gallons)
Type of Fuel ............................................................................................................. See Diesel fuel specifications
Hydraulic System
Hydraulic Reservoir Refill Capacity with Filter Change ................................................130 liters (34 U.S. Gallons)
Total System Capacity ............................................................................................242 liters (63.93 U.S. Gallons)
Type of Oil .................................................................................................................. AMBRA Hydrosystem 46HV
Transmission
Refill Capacity with Filter Change ...............................................................................22 litres (5.81 U.S. Gallons)
Type of Oil .................................................................................................. AMBRA Supergold HSP SAE 10W-30
Axles
Capacity
Front.................................................................................................................... 47.3 litres (12.50 U.S. Quarts)
Rear ............................................................................................................................. 53 litres (14 U.S. Quarts
Type of Lubricant .....................................................................................AMBRA TRX Transaxle Fluid, 80W-140
NOTE: DO NOT use an alternate oil in the axles. The brake components in the axles could be damaged as a result of using an
alternate oil. Machines are shipped from the factory with break-in oil.
Brake System
Type of Fluid (Same as Hydraulic System) ................................................................ AMBRA Hydrosystem 46HV

ENGINE OIL RECOMMENDATIONS

New Holland AMBRA Engine oil is recommended
See the cha rt below for
for use in your New Holland engine. New Holland
rec ommended visc osity at
AMBRA En g ine O il will lu b rica te y ou r e ng in e
ambie nt air tempe ratu re
correctly under all operating conditions.
ranges.
If New Holland AMBRA Multi-Viscosity Oil is not
NOTE: Do not put performance
available, use only oil meeting API engine oil service
additives or other oil additive
category CH -4 (preferred) or CG-4.
products in the engine crankcase.
The oil change intervals given in this
RH99K130
manual are according to tests with
New Holland AMBRA lubricants.
1002-4

HYDRAULIC OIL TEMPERATURE CHART

BC06B208

TRANSMISSION OIL TEMPERATURE CHART

BC06B209

ENGINE OIL TEMPERATURE CHART

BC06B150
 1002-5

DIESEL FUEL SYSTEM

Use No. 2 diesel fuel in the engine of this machine. Fuel Storage
The use of other fuels can cause the loss of engine
power and high fuel consumption. If you keep fuel in storage for a period of time, you
can get foreign material or water in the fuel storage
In very cold temperatures, a mixture of No. 1 and No. tank. Many engine problems are caused by water in
2 diesel fuels is temporarily permitted. See the the fuel.
following Note.
Keep the fuel storage tank outside and keep the fuel
NOTE: See your fuel dealer for winter fuel requirements in as cool as possible. Remove water from the storage
your area. If the temperature of the fuel lowers below the container at regular periods of time.
cloud point (wax appearance point), wax crystals in the fuel
will restrict the fuel filter and cause the engine to lose power Fill the fuel tank at the end of the daily operating
or not start. period to prevent condensation in the fuel tank.

The diesel fuel used in this machine must meet the

specifications as shown below in, “Specifications for
Acceptable No. 2 Diesel Fuel”, or “Specification
D975-81” of the American Society for Testing and
Materials.

Specifications for Acceptable No. 2 Diesel Fuel

API gravity, minimum ............................................................................................................................................. 34
Flash point, minimum ............................................................................................................................60°C (140°F)
Cloud point (wax appearance point), maximum ...........................................................-20°C (-5°F) See Note above
Pour point, maximum ..................................................................................................-26°C (-15°F) See Note above
Distillation temperature, 90% point ................................................................................282 to 338°C (540 to 640°F)
Viscosity, at 38°C (100°F)
Centistokes ......................................................................................................................................... 2.0 to 4.3
Cetane number, minimum .......................................................................... 43 (45 to 55 for winter or high altitudes)
Water and sediment, by volume, maximum .................................................................................................... 0.05%
Please Click Here

www.cnhmanualpdf.com

To Download Complete Manual

Feel free to Contact us

Support Email: sales@cnhmanualpdf.com