FP 6400 - Datasheet

Lab.
gruppen fP 6400
The fP 6400 is a lightweight and space-saving power amplifier

Heat and cooling are fundamental problems in extreme high power amplifiers such as the fP 6400. Already in 1990,
Lab.gruppen patented a high efficiency amplifier, in fact an evolution of the Class D amplifier. Lab.gruppen therefore call it
Class TD. It obtains the same high efficiency as Class D, but avoids its drawbacks. Class D has a power-amplifier topology using
Pulse Width Modulation (PWM) to achieve high efficiency, but it needs a recovery
filter between the output stage and the loudspeaker. Lab.gruppen’s Class TD amplifiers do not need this filter and this is one
reason why the Lab.gruppen Class TD obtains the same sonic quality as a traditional Class AB amplifier.
Besides the traditionally superb Lab.gruppen sonic performance, fP6400 offers a full line of important features:
Regulated switch mode power supply

Today there are many lightweight, switch-mode amplifiers in the market. However, the unique Lab.gruppen switch-mode power
supply technology
offers a number of essential advantages that make it superior to other and seemingly similar power supply designs. The most
important features are the regulated power supply and the extreme power efficiency. The regulated
power supply easily deals with a very high variation in the AC mains voltage: it can drop by up to 20% below its nominal level –
e.g. to 180 V instead of 230 V – without any problem. Perhaps even greater benefits result from the
extreme efficiency of Lab.gruppen amplifiers: only a fraction of the energy from the AC mains is turned into heat.
A regulated power supply also presents some other sonic advantages, such as better cone control and the same fast response
as a conventional power supply.
Multiple positions Gain switch

To meet the demands for a flexible gain structure in the system, Lab.gruppen offers a multiple position gain switch. The
maximum amplifier gain can be set to all industry standards: 20, 23, 26, 29, 32, 35, 38 and 41 dB.
Sophisticated protection circuitry, combining:
• DC protection; protects against infrasonic signals

• VHF protection;; protects the loudspeakers against strong very high frequency non-musical signals above the audible
range.
• Thermal protection; prevents the amplifier from being overheated. The protection indicators on the front panel are
switched on, as a warning, before the protection process is initiated.
• AC protection; shuts down the power supply if the line voltage is outside the operating voltage.
• Clip limiter; prevents severely clipped waveforms from reaching the
loudspeakers, whilst maintaining full peak power.
technical specifications
MAX OUTPUT POWER 1)
EIA at 1 kHz and 1% THD FTC 20-20kHz

@0.1%THD
MLS switch -5 dB -4 dB -2 dB 0 dB Full 0 dB Full
16 Ω per channel 220 W 260 W 410 W 650 W 640 W
2 Ω per channel 1660 W 2000 W 2400, 3050 3) 2900 2), 3200 2500 W
W 3)W
16 Ω bridged 860 W 1040 W 1640 W 2600 W 2500 W
8 Ω bridged 1660 W 2000 W 3200 W 4600 W 4400 W
4 Ω bridged 3400 W 4800, 6100 5800 2), 6400 5000 W

4000 W 3) W 3) W
Max output voltage
8 ohms load 62 Vrms 70 Vrms 85 Vrms 104 Vrms
Peak voltage, no load 88 V 101 V 121 V 149 V
Distortion etc.
THD 20Hz-20kHz
and 1W to full power 0,1 %
THD @ 1kHZ and –1dB
under clip 0,04 %
DIM 30 at –3dB under 0,06 %

clip
Hum and Noise <-110 dB
Channel separation 70 dB
@10kHz
Output impedance 60 mΩ
Slew Rate 20 V/µs
Inputs
Gain, selectable [dB] 20, 23, 26, 29,

32, 35, 38, 41
Impedance 20 ohm
Common mode rejection 50 dB

Front Panel
Gain controls (2) channel A, B 31 pos detent
Clip Indicator (2) red LEDs
Output headroom indicators (10) green Fast peak –slow release

LED’s
Temp Indicator (2) yellow LEDs 80°C at heatsink
VHF indicator (2) yellow LEDs <12kHz at full power
On Indicator (2) green LEDs DC rail voltage for channel A and

B
AC Indicator (1) green LED AC power present
AFS Indicator (1) green LED Fuse saver activated
Rear Panel
Input connectors (2) Neutrik Combo XLR type, 3 pin & 1/4” jack
Link connector (2) XLR type, 3 pin male
Output connectors (2) Neutrik 4-pole Speakon connectors
Switches
Clip limiter A and B On-Off (switchable)
MLS switch 0, -2, -4, -5dB
Link-switch Ch.A-B
Power 230 V version 115 V version
Operation voltage 130 V-265 V AC 65 V – 135 V AC
Minimum start voltage 175 V 95 V AC
Full output power at 4ohms 180 V-265 V AC 90 V – 130 V AC
Peak inrush current (Soft start 5A 5A

limited)
Current Draw @ 4ohms & 230V
Quiescent power (no load) 1 Arms 2 Arms
1/8 of full power (-9dB) 6 Arms 12 Arms
1/3 of full power (-5dB) 14 Arms 28 Arms
At full power (0 dB) @1 kHz 1% 20 Arms (AFS 40 Arms (AFS limited)

THD limited)
Net Dimensions mm (inch) 483 (19”) W x 88 (3,5”) H x 347 (13,7”) D
Shipping Dimensions mm (inch) 560 (22”) W x 180 (7.1”) H x 500 (19.7”) D

Net Weight 10 kg (22lbs)
Shipping Weight 11.6 kg (25.6lbs)
Approvals CE Emission EN 55 103-1, E3

Immunity EN 55 103-2, E3, with S/N below 1% at normal operation level
Safety EN 60 065, class I
• Specifications measured with 230 VAC

• Component tolerance dependent 4) Normal operation level 1/8 of full power or – 9dB
below clip level
• Continuous power, one channel driven or peak power both channels driven
(Thermal protection may occur at high continuous power)
• Normal operation level 1/8 of full power or –9dB below clip level.
Adamson Systems Engineering Inc.

1401 Scugog Line 6, Port Perry, ON L9L 1B2
T: [905] 982 0520 F: [905] 982 0609
www.adamsonproaudio.com
sales@adamsonproaudio.com
Specifications Are Subject To Change Without Notice

FP 6400 - Datasheet

Uploaded by

Copyright:

Available Formats

FP 6400 - Datasheet

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

FP 6400 - Datasheet

Uploaded by

Copyright:

Available Formats

Lab.

The fP 6400 is a lightweight and space-saving power amplifier

Regulated switch mode power supply

Multiple positions Gain switch

Sophisticated protection circuitry, combining:

• DC protection; protects against infrasonic signals

MAX OUTPUT POWER 1)

EIA at 1 kHz and 1% THD FTC 20-20kHz

MLS switch -5 dB -4 dB -2 dB 0 dB Full 0 dB Full

16 Ω per channel 220 W 260 W 410 W 650 W 640 W

8 Ω per channel 430 W 520 W 820 W 1300 W 1280 W

4 Ω per channel 830 W 1000 W 1600 W 2300 W 2200 W

16 Ω bridged 860 W 1040 W 1640 W 2600 W 2500 W

8 Ω bridged 1660 W 2000 W 3200 W 4600 W 4400 W

4 Ω bridged 3400 W 4800, 6100 5800 2), 6400 5000 W

Max output voltage

8 ohms load 62 Vrms 70 Vrms 85 Vrms 104 Vrms

Peak voltage, no load 88 V 101 V 121 V 149 V

and 1W to full power 0,1 %

THD @ 1kHZ and –1dB

under clip 0,04 %

DIM 30 at –3dB under 0,06 %

Hum and Noise <-110 dB

Slew Rate 20 V/µs

Gain, selectable [dB] 20, 23, 26, 29,

Common mode rejection 50 dB

Gain controls (2) channel A, B 31 pos detent

Clip Indicator (2) red LEDs

Output headroom indicators (10) green Fast peak –slow release

Temp Indicator (2) yellow LEDs 80°C at heatsink

VHF indicator (2) yellow LEDs <12kHz at full power

On Indicator (2) green LEDs DC rail voltage for channel A and

AC Indicator (1) green LED AC power present

AFS Indicator (1) green LED Fuse saver activated

Link connector (2) XLR type, 3 pin male

Output connectors (2) Neutrik 4-pole Speakon connectors

Clip limiter A and B On-Off (switchable)

MLS switch 0, -2, -4, -5dB

Power 230 V version 115 V version

Operation voltage 130 V-265 V AC 65 V – 135 V AC

Minimum start voltage 175 V 95 V AC

Full output power at 4ohms 180 V-265 V AC 90 V – 130 V AC

Peak inrush current (Soft start 5A 5A

Current Draw @ 4ohms & 230V

Quiescent power (no load) 1 Arms 2 Arms

1/8 of full power (-9dB) 6 Arms 12 Arms

1/3 of full power (-5dB) 14 Arms 28 Arms

At full power (0 dB) @1 kHz 1% 20 Arms (AFS 40 Arms (AFS limited)

Net Dimensions mm (inch) 483 (19”) W x 88 (3,5”) H x 347 (13,7”) D

Shipping Dimensions mm (inch) 560 (22”) W x 180 (7.1”) H x 500 (19.7”) D

Net Weight 10 kg (22lbs)

Shipping Weight 11.6 kg (25.6lbs)

Approvals CE Emission EN 55 103-1, E3

• Specifications measured with 230 VAC

Adamson Systems Engineering Inc.

Specifications Are Subject To Change Without Notice

You might also like