DATA SHEET

Operational amplifiers
Order code Manufacturer code Description
82-0258 LM358 LM358 LOW POWER OP AMPLIFIER (RC)

Operational amplifiers Page 1 of 12

The enclosed information is believed to be correct, Information may change ‘without notice’ due to Revision A
product improvement. Users should ensure that the product is suitable for their use. E. & O. E. 20/02/2007

Sales: 01206 751166 Technical: 01206 835555 Fax: 01206 751188

Sales@rapidelec.co.uk Tech@rapidelec.co.uk www.rapidonline.com
 LM158,A-LM258,A
LM358,A

LOW POWER DUAL OPERATIONAL AMPLIFIERS

.. INTERNALLY FREQUENCY COMPENSATED

. LARGE DC VOLTAGE GAIN : 100dB

WIDE BANDWIDTH (unity gain) : 1.1MHz

. (temperature compensated)
VERY LOW SUPPLY CURRENT/AMPLI
(500µA) - ESSENTIALLY INDEPENDENT OF

. SUPPLY VOLTAGE
LOW INPUT BIAS CURRENT : 20nA

.. (temperature compensated)
LOW INPUT OFFSET VOLTAGE : 2mV

. LOW INPUT OFFSET CURRENT : 2nA

INPUT COMMON-MODE VOLTAGE RANGE

. INCLUDES GROUND
DIFFERENTIAL INPUT VOLTAGE RANGE
N
DIP8
(Plastic Package)
D
SO8
(Plastic Micropackage)

. EQUAL TO THE POWER SUPPLY VOLTAGE

LARGE OUTPUT VOLTAGE SWING 0V TO
(VCC – 1.5V)

ORDER CODES
Part Temperature Package
Number Range N D
DESCRIPTION LM158,A –55oC, +125oC • •
These circuits consist oftwo independent,high gain, LM258,A
o
–40 C, +105 C
o
• •
internally frequency compensated which were

158-01.TBL
LM358,A o o
0 C, +70 C • •
designed specifically to operate from a single power
Example : LM258N
supply over a wide range of voltages.The low power
supply drain is independent of the magnitude of the
power supply voltage. PIN CONNECTIONS (top view)
Application areas include transducer amplifiers, dc
gain blocks and all the conventionalop-amp circuits
which now can be more easily implemented in single 1 8
power supply systems. For example, these circuits
can be directly operated off the standard + 5V power 2 - 7
supply voltage which is used in logic systems and
will easily provide the required interface electronics 3 + - 6
without requiring any additional power supply.
4 + 5
In the linear mode the input common-mode voltage
range includes ground and the output voltage can
also swing to ground, even though operated from
1 - Output 1 5 - Non-inverting input 2
only a single power supply voltage. 2 - Inverting input 1 6 - Inverting input 2
The gain-bandwidth product is temperature 3 - Non-inverting input 1 7 - Ouput 2
- +
compensated. 4 - VCC 8 - VCC

August 1996 1/11

LM158,A - LM258,A - LM358,A

SCHEMATIC DIAGRAM (1/2 LM158)

V CC

6µA
4µA 100µA
Q5
Q6
CC

Q2 Q3
Inverting Q7
input Q1 Q4
R SC

Non-inverting Q11
Output
input

Q13

Q10 Q12

Q8 Q9
50µA

GND

158-02.EPS

ABSOLUTE MAXIMUM RATINGS

Symbol Parameter LM158,A LM258,A LM358,A Unit
VCC Supply Voltage +32 +32 +32 V
Vi Input Voltage –0.3 to +32 –0.3 to +32 –0.3 to +32 V
Vid Differential Input Voltage +32 +32 +32 V
Output Short-circuit Duration - (note 2) Infinite
Ptot Power Dissipation 500 500 500 mW
Iin Input Current - (note 1) 50 50 50 mA
o
158-02.TBL

Toper Operating Free-air Temperature Range –55 to +125 –40 to +105 0 to +70 C
o
Tstg Storage Temperature Range –65 to +150 –65 to +150 –65 to +150 C

2/11
 LM158,A - LM258,A - LM358,A

ELECTRICAL CHARACTERISTICS
VCC+ = +5V, VCC– = Ground, VO = 1.4V, Tamb = 25oC (unless otherwise specified)
LM158A-LM258A LM158-LM258
Symbol Parameter LM358A LM358 Unit
Min. Typ. Max. Min. Typ. Max.
Vio Input Offset Voltage - (note 3) mV
Tamb = 25oC 1 3 2 7
LM158, LM258 5
LM158A 2
Tmin. ≤ Tamb ≤ Tmax. 4 9
LM158, LM258 7
Iio Input Offset Current nA
o
Tamb = 25 C 2 10 2 30
Tmin. ≤ Tamb ≤ Tmax. 30 40
Iib Input Bias Current - (note 4) nA
o
Tamb = 25 C 20 50 20 150
Tmin. ≤ Tamb ≤ Tmax. 100 200
Avd Large Signal Voltage Gain V/mV
(VCC = +15V, RL = 2kΩ, VO = 1.4V to 11.4V)
Tamb = 25oC 50 100 50 100
Tmin. ≤ Tamb ≤ Tmax. 25 25
SVR Supply Voltage Rejection Ratio (RS = 10kΩ) dB
+
(VCC = 5 to 30V)
o
Tamb = 25 C 65 100 65 100
Tmin. ≤ Tamb ≤ Tmax. 65 65
ICC Supply Current, all Amp, no Load mA
VCC = +5V, Tmin. ≤ Tamb ≤ Tmax. 0.7 1.2 0.7 1.2
VCC = +30V, Tmin. ≤ Tamb ≤ Tmax. 2 2
Vicm Input Common Mode Voltage Range V
(VCC = +30V) - (note 6)
o + +
Tamb = 25 C 0 VCC –1.5 0 VCC –1.5
+ +
Tmin. ≤ Tamb ≤ Tmax. 0 VCC –2 0 VCC –2
CMR Common-mode Rejection Ratio (RS = 10kΩ) dB
o
Tamb = 25 C 70 85 70 85
Tmin. ≤ Tamb ≤ Tmax. 60 60
Isource Output Current Source mA
(VCC = +15V, Vo = 2V, Vid = +1V) 20 40 20 40
IO Short Circuit to Ground (VCC = +15V) 40 60 40 60 mA
Isink Output Current Sink (Vid = -1V)
VCC = +15V, VO = 2V 10 20 10 20 mA
VCC = +15V, VO = +0.2V 12 50 12 50 µA
VOPP Output Voltage Swing (RL = 2kΩ) V
o + +
Tamb = 25 C 0 VCC –1.5 0 VCC –1.5
+ +
Tmin. ≤ Tamb ≤ Tmax. 0 VCC –2 0 VCC –2
+
VOH High Level Output Voltage (V CC = 30V) V
o
Tamb = 25 C RL = 2kΩ 26 27 26 27
Tmin. ≤ Tamb ≤ Tmax. 26 26
o
Tamb = 25 C RL = 10kΩ 27 28 27 28
Tmin. ≤ Tamb ≤ Tmax. 27 27
VOL Low Level Output Voltage (R L = 10kΩ) mV
o
Tamb = 25 C 5 20 5 20
Tmin. ≤ Tamb ≤ Tmax. 20 20
SR Slew Rate (VCC = 15V, VI = 0.5 to 3V, RL = V/µs
o
2kΩ, C L = 100pF, Tamb = 25 C, unity gain) 0.3 0.6 0.3 0.6
GBP Gain Bandwidth Product MHz
o
(VCC = 30V, f = 100kHz, Tamb = 25 C,
Vin = 10mV, R L = 2kΩ, C L = 100pF) 0.7 1.1 0.7 1.1
THD Total Harmonic Distortion %
(f = 1kHz, Av = 20dB, RL = 2kΩ, VCC = 30V, 0.02 0.02
CL = 100pF, Tamb = 25oC, VO = 2 PP)
158-03.TBL

en Equivalent Input Noise voltage nV

(f = 1kHz, Rs = 100Ω, VCC = 30V) 55 55 √
 Hz

3/11
LM158,A - LM258,A - LM358,A

ELECTRICAL CHARACTERISTICS (continued)

LM158A LM158
LM258A LM258
Symbol Parameter LM358A LM358 Unit
Min. Typ. Max. Min. Typ. Max.
DVio Input Offset Voltage Drift 7 15 7 30 µV/oC
DIio Input Offset Current Drift 10 200 10 300 pA/oC

158-04.TBL
VO1/VO2 Channel Separation (note 5) dB
1kHz ≤ f ≤ 20kHz 120 120
N otes : 1. This input current only exist when the voltage at any of the input leads is driven negative. It is due to the collec-
tor-base junction of the input PNP transistor becoming forward biased and thereby acting as input diode clamps.
In additi on to this diode action, there is also NPN parasitic action on the IC chip. This transistor action can cause
the output voltages of the Op-amps to go to the VCC voltage level (or to ground for a large overdrive) for the time
duration that an input is driven negative.
This is not destructive and normal output will set up again for input voltage higher than –0.3V.
2. Short-circuits from the output to VCC can cause excessive heating if VCC + > 15V. The maximum output current is
approximatively 40mA independent of the magnitude of VCC . Destructive dissipation can result from simultaneous
short-circuits on all amplifiers.
3. VO = 1.4V, RS = 0Ω, 5V < VCC+ < 30V, 0 < Vic < VCC + – 1.5V.
4. The direction of the input current is out of the IC. This current is essentially constant, independent of the state of
the output so no loading change exists on the input lines.
5. Due to the proximity of external components insure that coupling is not originating via stray capacitance between
these external parts. This typically can be detected as this type of capacitance increases at higher frequences.
6. The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than
0.3V. The upper end of the common-mode voltage range is VCC+ – 1.5V.
But either or both inputs can go to +32V without damage.

OP EN LOO P FREQ UENCY RES P ONS E (NOTE 3) LARGE S IGNAL FREQUENCY RES PONS E
140 20
100k Ω
10M Ω
120 0.1 µF 1k Ω +15V
OUTPUT SWING (Vpp)

-
VCC
VOLTAGE GAIN (dB)

- VO
100 VI VO 15 VI
VCC /2 + 2k Ω
+ +7V
80
VCC = 30V &
-55 C Tamb +125 C 10
60

40
5
20 VCC = +10 to + 15V &
-55 C Tamb +125 C
0 0
1.0 10 100 1k 10k 100k 1M 10M 1k 10k 100k 1M

FREQUENCY (Hz) FR EQUENCY (Hz)

VOLAGE FOLLOWER P ULSE R ES PONSE OUTP UT CHARACTER ISTICS
4 10
VCC = +5V
VOLTAGE (V)

RL 2 k Ω
OUTPUT

3 VCC = +15V VCC = +15V

OUTPUT VOLTAGE (V)

VCC = +30V
2
1
1
v cc
0
v cc /2
-
3 0.1 IO
VOLTAGE (V)

2 + VO
INPUT

1 Ta mb = +25 C
0.01
0 10 20 30 40 0,001 0,01 0,1 1 10 100

TIME (µs ) OUTP UT S INK C URRENT (mA)

4/11
 LM158,A - LM258,A - LM358,A

VOLTAGE FOLLOWER PULSS E RESP ONS E OUTP UT CHARACTERISTICS

(S MALLS IGNAL)

OUTPUT VOLTAGE REFERENCED

8
500 VCC
OUTPUT VOLTAGE (mV)

7
+
450 eO 6 V CC /2 + VO
el -

TO VCC+ (V)
50pF
400 5 - IO

Inpu t 4
350
Independent of V CC
Outpu t 3
300 T a mb = +25 C
2
Tamb = +2 5 C
VCC = 3 0 V
250 1
0 1 2 3 4 5 6 7 8 0,001 0,0 1 0,1 1 10 100

TIME (µs ) OUTP UT S OURCE CURRENT (mA)

INPUT CURRENT (No te 1) CURRENT LIMITING (Note 1)
90 90
-
80 VI = 0 V OUTPUT CURRENT (mA) 80 IO
INPUT CURRENT (mA)

70 70
VCC = +30 V 60
60 +

50 50
VCC = +15 V 40
40

30 30

20 VCC = +5 V 20

10 10

0 0
-55 -35 -15 5 25 45 65 85 105 125
-55 -35 -15 5 25 45 65 85 105 125

TEMPERATURE ( C) TEMPERATURE ( C)
INPUT VOLTAGE RANGE S UPP LY CURRENT
4
15
VCC
SUPPLY CURRENT (mA)
INPUT VOLTAGE (V)

mA ID
3
10 -
NØga tive
2
+

5 P os itive
Ta mb = 0 C to +125 C
1

Ta mb = -55 C

0 5 10 15 0 10 20 30

P OWER S UPP LY VOLTAGE (–V) P OSITIVE S UPP LY VOLTAGE (V)

5/11
LM158,A - LM258,A - LM358,A

160 100
R L = 20k Ω

INPUT CURRENT (nA)

VOLTAGE GAIN (dB)

120 75

80 R L = 2k Ω 50

40 25
Tamb= +25 C

0 10 20 30 40 0 10 20 30

158-06.EPS
158-05.EPS

P OS ITIVE S UP P LY VOLTAGE (V) P OS ITIVE S UP P LY VOLTAGE (V)

160 GAIN BANDWIDTH PRODUCT (MHz)

1.5
R L = 20k Ω 1.35
VOLTAGE GAIN (dB)

120 1.2
1.05

80 R L = 2k Ω 0.9
0.75 VCC = 15V
0.6
40 0.45
0.3
0.15
0
0 10 20 30 -55-35-15 5 25 45 65 85 105 125

158-08.EPS
158-07.EPS

P OS ITIVE S UP P LY VOLTAGE (V) TEMPERATURE ( C)

POWER SUPPLY REJECTION RATIO (dB)

COMMON MODE REJECTION RATIO (dB)

115 115
110 110
105 SVR 105
100 100
95 95
90 90
85 85
80 80
75 75
70 70
65 65
60-55-35-15 5 25 45 65 85 105 125 60-55-35-15 5 25 45 65 85 105 125
158-09.EPS

158-10.EPS

TEMPERATURE ( C) TEMPERATURE ( C)

6/11
 LM158,A - LM258,A - LM358,A

TYPICAL APPLICATIONS (single supply voltage) VCC = +5V DC

AC COUPLED INVERTING AMPLIFIER AC COUPLED NON-INVERTING AMPLIFIER

Rf R1 R2
100kΩ Rf
100k Ω 1MΩ
A V =- AV = 1 + R2
R1 R1
R1 (as shown AV = -10)
CI (as shown AV = 11)
10kΩ C1
0.1µF
Co Co
1/2 0 2VPP 1/2 2VPP
0
LM158 eo CI LM158 eo

RB RL RB RL
6.2kΩ 10kΩ 6.2kΩ
eI ~ 10kΩ
R2 R3
R3
VCC 100kΩ 100kΩ eI ~
1MΩ
R4
100kΩ

VCC
C1
C2 R5
10µF
10µF 100kΩ
158-11.EPS

158-12.EPS
NON-INVERTING DC AMPLIFIER DC SUMMING AMPLIFIER

e1 100kΩ

R2
AV = 1 +
R1
10k Ω (As shown A V = 101)
1/2 eO
1/2 eO +5V 100kΩ
LM158 LM158
e2 100kΩ
e O (V)

R2
R1
1MΩ e3 100kΩ
10kΩ

100kΩ
0
e I (mV)

e4 100kΩ

eo = e 1 + e2 - e3 - e4
where (e1 + e2) ≥ (e 3 + e4)
158-13.EPS

158-14.EPS

to keep eo ≥ 0V

7/11
LM158,A - LM258,A - LM358,A

HIGH INPUT Z, DC DIFFERENTIAL USING SYMMETRICAL AMPLIFIERS TO

AMPLIFIER REDUCE INPUT CURRENT

1/2
I I B LM158 eo
I

eI
IB
R2 R4 2N 929
100kΩ 100kΩ
R1
0.001 µ F
100kΩ R3
1/2 100kΩ IB
LM158 1/2 IB
+V1 LM158 Vo 1/2
3MΩ
+V2 LM158

Input current compensation

IB
if R1 = R 5 and R 3 = R 4 = R 6 = R7 1.5MΩ
2R1
eo = [ 1+ ] (e2 − e1)
R2
As shown eo = 101 (e2 - e1).

158-16.EPS
158-15.EPS

HIGH INPUT Z ADJUSTABLE GAIN DC LOW DRIFT PEAK DETECTOR

INSTRUMENTATION AMPLIFIER

R1
100kΩ
IB

R3 R4 1/2
100kΩ 100k Ω I B LM158 eo
1/2 1/2
e1 LM158
LM158 C Zo
eI 2IB
1/2 eO 1µF

Gain adjust
LM158 ZI
R2
2N 929 0.001 µF
2k Ω R5
100k Ω
2IB IB

R6 R7 R 3R 1/2
1/2 100k Ω 100k Ω 1MΩ 3MΩ LM158
LM158 Input current
e2 IB compensation

if R 1 = R 5 and R 3 = R 4 = R 6 = R 7
2R1
e o = [ 1+ ] (e2 − e 1)
R2
158-18.EPS
158-17.EPS

As shown eo = 101 (e2 - e 1)

8/11
 LM158,A - LM258,A - LM358,A

ACTIVE BAND-PASS FILTER

R1
100kΩ
C1
330pF
R2 1/2
R5
100kΩ LM158
+V1 470kΩ
R4
10MΩ 1/2
LM158
C2
330pF R6
R3 470kΩ
100kΩ Vo
1/2 R7
LM158 100kΩ
VCC
C3
R8
10µF
Fo = 1kHz 100k Ω
Q = 50

158-19.EPS
AV = 100 (40dB)

9/11
LM158,A - LM258,A - LM358,A

PACKAGE MECHANICAL DATA

8 PINS - PLASTIC DIP

PM-DIP8.EPS
Millimeters Inches
Dim.
Min. Typ. Max. Min. Typ. Max.
A 3.32 0.131
a1 0.51 0.020
B 1.15 1.65 0.045 0.065
b 0.356 0.55 0.014 0.022
b1 0.204 0.304 0.008 0.012
D 10.92 0.430
E 7.95 9.75 0.313 0.384
e 2.54 0.100
e3 7.62 0.300
e4 7.62 0.300
F 6.6 0260
i 5.08 0.200
L 3.18 3.81 0.125 0.150
DIP8.TBL

Z 1.52 0.060

10/11
 LM158,A - LM258,A - LM358,A

PACKAGE MECHANICAL DATA

8 PINS - PLASTIC MICROPACKAGE (SO)

PM-SO8.EPS
Millimeters Inches
Dim.
Min. Typ. Max. Min. Typ. Max.
A 1.75 0.069
a1 0.1 0.25 0.004 0.010
a2 1.65 0.065
a3 0.65 0.85 0.026 0.033
b 0.35 0.48 0.014 0.019
b1 0.19 0.25 0.007 0.010
C 0.25 0.5 0.010 0.020
o
c1 45 (typ.)
D 4.8 5.0 0.189 0.197
E 5.8 6.2 0.228 0.244
e 1.27 0.050
e3 3.81 0.150
F 3.8 4.0 0.150 0.157
L 0.4 1.27 0.016 0.050
M 0.6 0.024
SO8.TBL

o
S 8 (max.)

Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsi-
bility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which
may result from its use. No license is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON
Microelectronics. Specification mentioned in this publi cation are subject to change without notice. This publication supersedes
and replaces all information previously supplied. SGS-THOMSON Microelectronics products are not authorized for use as critical
components in life support devices or systems without express written approval of SGS-THOMSON Microelectronics.

 1996 SGS-THOMSON Microelectronics – Printed in Italy – All Rights Reserved

ORDER CODE :

SGS-THOMSON Microelectronics GROUP OF COMPANIES

Australia - Brazil - Canada - China - France - Germany - Hong Kong - Italy - Japan - Korea - Malaysia - Malta - Morocco
The Netherlands - Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A.

11/11