Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 10 views

    JOST KDL-9006w

    Uploaded by

    Nicolas Wang
    casatraileros.com, heavy duty truck & trailer spare parts.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    JOST KDL-9006w

    Uploaded by

    Nicolas Wang
    10 views2 pages
    casatraileros.com, heavy duty truck & trailer spare parts.

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    casatraileros.com, heavy duty truck & trailer spare parts.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    10 views2 pages

    JOST KDL-9006w

    Uploaded by

    Nicolas Wang
    casatraileros.com, heavy duty truck & trailer spare parts.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    You are on page 1of 2

    Ball Bearing Turntables and Slewing rings

    Slewing ring – Series KDL9006W


    Low Profile Ballrace Models

    CB ∅ H

    ∅B
    Model
    ∅F KDL9006W Supplied Pre-Drilled
    Typical applications: Fridge Vans Stock Crate
    ∅D D-Value Rating*: 240kN

    12 • Slewing rings are supplied primed for corrosion


    protection.
    56 • Material C45.
    • Ball race hardened.
    12
    • 8 conical lubrication nipples AM 8 × 1
    according to DIN 71412.
    ca. ∅ G
    ∅C *As tested in a JOST assembly
    ∅E
    The below axial loads are applicable if the slewing ring is
    ∅A mounted to the front axle of a trailer at speeds of up to
    105 km/h (65 m.p.h.). If it is to be used in self steering systems
    = shaped profile or above a fifth wheel please contact us for the maximum
    permissible loads by submitting construction data.

    ∅A ∅B ∅C ∅D ∅E ∅F ∅G ∅H Weight Axial load


    Type mm mm mm mm mm mm approx. mm approx. mm approx. kg kN
    KDL9001 520 409 412 302 490 332 371 451 25 40
    KDL9002 650 539 542 432 620 462 501 581 32 80
    KDL9003 750 639 642 532 720 562 601 681 38 120
    KDL9004 850 739 742 632 820 662 701 781 44 150
    KDL9005 950 839 842 732 920 762 801 881 50 180
    *KDL9006W 1050 939 942 832 1020 862 901 981 56 210
    KDL9007 1200 1089 1092 982 1170 1012 1051 1131 65 250

    The measurements are subject to our standard tolerances.

    17
    Ball Bearing Turntables and Slewing rings

    Fitting and Maintenance Instructions for Slewing Rings KDL900/6W

    Direction
    of travel
    Frame A-Frame
    Hexagon bold DIN 960
    M 16 x 1,5 – 8.8 tightened to 225 Nm;
    alternatively M16 – 8.8, tightened to 210 Nm,
    according to DIN 931
    ca. 4
    5°
    Ball insertion
    hole (inner ring) Type plate
    (outer ring) X

    Alternative mounting with


    head bolt underneath,
    Upper Lower counter nut also admissible.
    construction construction

    Hexagon nut DIN 980


    M 16 x 1,5 – 8 resp. M 16 – 8

    Welded stops above and below

    1. The slewing ring must be mounted on a completely flat lubricating the slewing ring should be turned so that the
    (max. unevenness 1mm) and rigid base with at least 50% grease is evenly distributed. If a central lubrication system is
    of the circumference adequately supported. Particular to be used we recommend increasing the number of grease
    attention must be paid to the support of the web section nipples (please state on order) and using a high quality
    area containing the slewing ring races. Any unevenness lithium saponified ball bearing grease of at least NLGI class
    under the flanges can be corrected with metal strips or by 1.
    filling in with plastic metal.
    5. The slewing ring must be lubricated according to use but
    2. Each flange must be attached with at least 12 high tensile at least once every 3 months or 25,000 km, using a high
    bolts M 16 × 1,5 of at least grade 8.8. Do not drill in the quality ball bearing grease (lithium saponified, NLGI CLASS
    area of the ball insertion hole, which should be at less 2). Whilst lubricating the A-frame should be turned so that
    than 45° to the direction of travel. The thickness of paint the grease is evenly distributed.
    between slewing ring and mounting should not exceed 50
    microns to guarantee the fit to be friction-tight. The tightness of the mounting bolts should also be checked
    at regular service intervals.
    3. To ease the shear load on the mounting bolts in the case
    of horizontal force at least 4 blocks should be welded on 6. Slewing rings are subject to wear. The limit of wear is
    immediately adjoining each flange. The slewing ring must reached when the axial play is 3.5 mm. This is at the latest
    not be mounted by means of welding. the case when the distance X < 8 mm at any point on the
    circumference.
    4. JOST slewing rings are initially lubricated before they leave
    the factory. Before they are put into operation for the first Wear Limits
    time however they must be adequately re-lubricated with Radial play - max. 3.0mm
    ball bearing grease (lithium saponified, NLGI class 2). Whilst Axial play - max. 2.5mm

    18

    You might also like