Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 261 views

    Fem 9 511

    Uploaded by

    Emilio Jose Andia Abregi
    249510431-FEM-9-511

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Fem 9 511

    Uploaded by

    Emilio Jose Andia Abregi
    261 views2 pages
    249510431-FEM-9-511

    Original Title

    249510431-FEM-9-511

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    249510431-FEM-9-511

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    261 views2 pages

    Fem 9 511

    Uploaded by

    Emilio Jose Andia Abregi
    249510431-FEM-9-511

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    You are on page 1of 2

    RailLok™ Series

    WELDABLE CLIPS - W15

    Adjustment range

    Patented

    New features :

    • Double wedge with patented


    self-contact design of
    inclined bolt
    • Bolts incorporate a
    “Square Shank Base”

    CLIPS C max Lateral Bolt torque Maximum resistance Estimated


    adjustment to lateral forces (*) weight
    mm mm Nm kN kg
    W15/AN 30 12 200 120 0.880
    W15/BN 34 12 200 120 0.880
    W15/CN 41 12 200 120 0.912
    W15/DN 45 12 200 120 0.922

    N: nose height, not compressed, adapted to the rail type (see table overleaf).
    (*) Higher side loads can be accepted depending on application, duty cycle and other external factors.
    Contact Gantrex for confirmation of side load in your application.

    Full designation Notes overleaf

    W15/AN • Clip Specification


    or W15/BN • Clip Selection Table
    or W15/CN Upper component and nose height (N)
    or W15/DN according to rail type and foot size (F).
    Components • Components Materials
    1x Sp M16 Cl8 GAL • Installation and Welding Instructions
    - Recommended weld throat size :
    1 xFull designation
    W15/28N 5 mm; weld leg size being then 7 mm.
    or 1 x W15/29N
    - Any low hydrogen rod suitable for use with
    or 1 x W15/35N structural steel may be used.
    or 1 x W15/39N
    1 x SSB M16x35 8.8 GAL

    1 x W15/23

    GXHQ-EN 2017-09 R2.0

    www.gantrex.com
    GANTREX Group – info@gantrex.com
    RailLok™ Series
    WELDABLE CLIPS - W15

    CLIP SPECIFICATION
    The RailLok™ patented clips are specifically designed to facilitate correct mounting of crane rails :
    • The patented design with inclined bolt ensures tight and full self-contact with the rail foot.
    • Bolts with “Square Shank Base” allow the use of impact-wrenches.
    • Easier installation because of the wider adjustment range.
    • Compact design : fits narrow girders and soleplates, avoid interference with guide rollers.
    Once installed, the clips are self-locking and self-tightening.

    CLIP SELECTION TABLE


    Mounting
    F K H Weight with without
    mm mm mm kg/m
    7 mm RailLok™ pad
    A65 175.0 65.0 75.0 43.10 W15/BJ W15/AM
    A75 200.0 75.0 85.0 56.20 W15/BI W15/AM
    A100 200.0 100.0 95.0 74.30 W15/BH W15/AJ
    A120 220.0 120.0 105.0 100.00 W15/CJ W15/BM
    CR73 140.0 100.0 135.0 73.30 W15/CJ W15/BJ
    CR100 155.0 120.0 150.0 100.20 W15/CH W15/BH
    MRS52 (105 CR) 131.8 65.1 131.8 52.09 W15/BH W15/AJ
    MRS67 (135 CR) 131.8 79.4 146.1 66.97 W15/CM W15/BM
    MRS85 (171 CR) 152.4 101.6 152.4 84.83 W15/CI W15/BJ
    MRS87A (PRI 85R) 152.4 101.6 152.4 86.80 W15/CI W15/BJ
    MRS87B (175 CR) 152.4 102.4 152.4 86.80 W15/CJ W15/AI
    QU80 130.0 80.0 130.0 63.69 W15/BI W15/AJ
    QU100 150.0 100.0 150.0 88.96 W15/CM W15/AI
    49E1 125.0 67.0 149.0 49.39 W15/BI W15/AM
    S49 125.0 67.0 149.0 49.43 W15/BI W15/AM
    54E1 (UIC 54) 140.0 70.0 159.0 54.77 W15/BI W15/AJ
    60E1 (UIC 60) 150.0 72.0 172.0 60.21 W15/BI W15/AJ
    Note : All dimensions are rounded off to serve as general guidelines only. Contact Gantrex for rail sizes not shown above and for help
    selecting rail pads.

    COMPONENTS MATERIALS

    The RailLok™ W15 is standard with a weldable forged steel lower component, a ductile cast iron upper component and vulcanize-bonded
    rubber nose. As standard, the bolts and nuts are hot dip galvanized. The upper component can also be hot dip galvanized on request.
    Contact Gantrex for other options.

    INSTALLATION AND SUGGESTED WELD INSTRUCTIONS

    The lower component is welded on the support parallel to the axis of the rail and the upper component is fastened to it by means of one
    bolt and nut. The recommended torque is 200 Nm. Electrical and pneumatic torque wrenches are allowed as long as the minimum torque
    of 150 Nm is met and the torque does not exceed 250 Nm. It is recommended the torque is regularly controlled with a calibrated torque
    wrench. It is recommended the torque is regularly controlled with a calibrated torque wrench.
    For most applications, the recommended weld throat size is 5 mm; the weld leg size is then 7 mm. If the pad is not used, the weld along
    the foot of the rail must be adapted. Use any low hydrogen rod suitable for use with structural steel: ISO2560 type E 42 5 B 32 H5, E7018
    or equivalent. For full instructions on weld size and electrodes, refer to the data sheet “Installation and suggested weld instructions”.
    Do not apply protective coating on the contact surface between upper and lower components unless accepted by Gantrex. Do not use sol-
    vents as they may seriously damage the rubber nose.

    We reserve the right to discontinue or change specifications or design at any time without prior notice and without
    incurring any obligation whatsoever.

    GXHQ-EN 2017-09 R2.0

    www.gantrex.com
    GANTREX Group – info@gantrex.com

    You might also like