Chiller Carrier

AQUAFORCE
30XA080-500
Air-Cooled Liquid Chillers
Installation Instructions
CONTENTS
SAFETY CONSIDERATIONS
Page
SAFETY CONSIDERATIONS . . . . . . . . . . . . . . . . . . . . . . 1
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-70
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Step 1 Inspect Shipment . . . . . . . . . . . . . . . . . . . . . . 2
Step 2 Place, Mount and Rig Unit. . . . . . . . . . . . . 2
PLACING UNIT
MOUNTING UNIT
RIGGING UNIT
Step 3 Cooler Fluid and Drain Piping
Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
GENERAL
UNITS WITH A HYDRONIC PUMP PACKAGE
UNITS WITHOUT A HYDRONIC PUMP PACKAGE
DUAL CHILLER CONTROL
COOLER FLUID, VENT, AND DRAIN
COOLER PUMP CONTROL
BRINE UNITS
WATER TREATMENT
PREPARATION FOR YEAR-ROUND OPERATION
Step 4 Fill the Chilled Water Loop . . . . . . . . . . . . 48
WATER SYSTEM CLEANING
WATER TREATMENT
SYSTEM PRESSURIZATION
FILLING THE SYSTEM
SET WATER FLOW RATE
PUMP MODIFICATION/TRIMMING
FREEZE PROTECTION
PREPARATION FOR WINTER SHUTDOWN
Step 5 Make Electrical Connections . . . . . . . . . . 54
POWER SUPPLY
FIELD POWER CONNECTIONS
POWER WIRING
FIELD CONTROL POWER CONNECTIONS
CARRIER COMFORT NETWORK
COMMUNICATION BUS WIRING
NON-CCN COMMUNICATION WIRING
FIELD CONTROL OPTION WIRING
DUAL CHILLER LEAVING WATER SENSOR
Step 6 Install Accessories . . . . . . . . . . . . . . . . . . . . 69
ENERGY MANAGEMENT MODULE
REMOTE ENHANCED DISPLAY
LOW AMBIENT TEMPERATURE OPERATION
MINIMUM LOAD ACCESSORY
UNIT SECURITY/PROTECTION ACCESSORIES
COMMUNICATION ACCESSORIES
SERVICE OPTIONS
CONTROL TRANSFORMER
Step 7 Leak Test Unit . . . . . . . . . . . . . . . . . . . . . . . . . 70
Step 8 Refrigerant Charging . . . . . . . . . . . . . . . . . . 70
DEHYDRATION
REFRIGERANT CHARGE
Installing, starting up, and servicing this equipment can be

hazardous due to system pressures, electrical components, and
equipment location. Only trained, qualified installers and service
mechanics should install, start up, and service this equipment.
When working on the equipment, observe precautions in the
literature, and on tags, stickers, and labels attached to the
equipment.
Follow all safety codes.
Wear safety glasses and work gloves.
Use care in handling, rigging, and setting bulky equipment.
Electrical shock can cause personal injury and death. Shut

off all power to this equipment during installation. There
may be more than one disconnect switch. Tag all disconnect locations to alert others not to restore power until work
is completed.
IMPORTANT: This equipment generates, uses, and
can radiate radio frequency energy and if not installed
and used in accordance with these instructions may
cause radio interference. It has been tested and found
to comply with the limits of a Class A computing
device as defined by FCC (Federal Communications
Commission, U.S.A.) regulations, Subpart J of Part 15,
which are designed to provide reasonable protection
against such interference when operated in a commercial environment.
INTRODUCTION
These instructions cover installation of 30XA080-500 aircooled liquid chillers with electronic controls and units with
factory-installed options (FIOPs). See Fig. 1.
Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.
Catalog No. 04-53300008-01
Printed in U.S.A.
Form 30XA-5SI
Pg 1
9-06
Replaces: 30XA-1SI
Book 2
Tab 5c
can be reduced to 3 ft (1 m) without sacrificing performance as

long as the remaining three sides are unrestricted. Acceptable
clearance on the side with a control box can be reduced to 4 ft
(1.3 m) due to NEC regulations, without sacrificing performance
as long as the remaining three sides are unrestricted. Provide ample room for servicing and removing the cooler. See Fig. 2-10 for
required clearances. Local codes for clearances take precedence
over the manufacturers recommendations when local codes call
for greater clearances.
If multiple units are installed at the same site, a separation of
10 ft (3 m) between the sides of the machines is required to
maintain proper airflow and minimize the chances of condenser air recirculation.
MOUNTING UNIT The unit may be mounted on a level
pad directly on the base rails, on a raised mounting rail around
the unit, or on vibration isolation springs. For all units, ensure
placement area is strong enough to support unit operating
weight. See Tables 1A and 1B. Mounting holes are provided
for securing the unit to the pad, mounting rail or vibration
isolation springs. Bolt the unit securely to pad or rails. If vibration isolators (field-supplied) are required for a particular
installation, refer to unit weight distribution in Fig. 11A-11C to
aid in the proper selection of isolators. The 30XA units can be
mounted directly on spring isolators.
INSTALLATION
Storage If the unit is to be stored for a period of time before installation or start-up, be sure to protect the machine
from construction dirt. Keep protective shipping covers in
place until the machine is ready for installation.
Step 1 Inspect Shipment Inspect unit for dam-
age upon arrival. If damage is found, immediately file a claim

with the shipping company, and contact your local Carrier
representative.
Step 2 Place, Mount, and Rig the Unit
When considering a location for the unit, be sure to consult

NEC (National Electrical Code, U.S.A.) and/or local code
requirements. Allow sufficient space for airflow, wiring, piping, and service. See Fig. 2-10.
NOTE: To facilitate refrigerant vent piping, all units have fusible plugs with 1/4 in. SAE (Society of Automotive Engineers)
flares and pressure reliefs with 3/4 in. NPT fittings (if required
by local codes).
PLACING UNIT Locate the unit so that the condenser
airflow is unrestricted both above and on the sides of the unit.
Airflow and service clearances are 6 ft (1.8 m) around the unit.
Acceptable clearance on the sides or ends without control boxes
30XA Air-Cooled AquaForce Chiller
Packaging/Security Options
L Coil Face Shipping Protection (CFSP)
0 CFSP, Skid
1 Skid, Top Crate, Bag
3 CFSP, Coil Trim Panels
4 CFSP, Skid, Coil Trim Panels, Shipping
5 Skid, Top Crate, Bag, Coil Trim Panels
7 CFSP, Coil Trim Panels, Upper & Lower Grilles
8 CFSP, Skid, Coil Trim Panels, Upper & Lower Grilles
9 Skid, Top Crate, Bag, Coil Trim Panels, Upper & Lower Grilles
C CFSP, Trim Panels, Upper & Lower Grilles, Hail Guards
D CFSP, Skid, Coil Trim Panels, Upper & Lower Grilles, Hail Guards
F Skid, Top Crate, Bag, Trim Panels, Upper & Lower Grilles, Hail Guards
Design Series
Unit Sizes
080 140 240
090 160 260
100 180 280
110 200 300
120 220 325
350
400
450
500
Voltage
1 575-3-60
2 380-3-60
4 230-3-60
6 460-3-60
7 200-3-60
Controls/Communication Options
- Navigator Display
0 Navigator Display, EMM
1 Navigator Display, Service Option
2 Navigator Display, EMM, Service Option
3 Touch Pilot Display
4 Touch Pilot Display, EMM
5 Touch Pilot Display, Service Option
6 Touch Pilot Display, EMM, Service Option
7 Navigator Display, BACnet Translator
8 Navigator Display, BACnet Translator, EMM
9 Navigator Display, BACnet Translator, Service Option
B Navigator Display, BACnet Translator, EMM, Service Option
C Touch Pilot Display, BACnet Translator
D Touch Pilot Display, BACnet Translator, EMM
F Touch Pilot Display, BACnet Translator, Service Option
G Touch Pilot Display, BACnet Translator, EMM, Service Option
H Navigator Display, LON Translator
J Navigator Display, LON Translator, EMM
K Navigator Display, LON Translator, Service Option
L Navigator Display, LON Translator, EMM, Service Option
M Touch Pilot Display, LON Translator
N Touch Pilot Display, LON Translator, EMM
P Touch Pilot Display, LON Translator, Service Option
Q Touch Pilot Display, LON Translator, EMM, Service Option
Condenser Coil/Low Sound Options

6 Aluminum Fin/Copper Tube, High Ambient Temperature,
Compressor Enclosures
8 Aluminum Pre-Coat Fin/Copper Tube, High Ambient Temperature,
9 Aluminum E-Coat Fin/Copper Tube, High Ambient Temperature,
F Aluminum Fin/Copper Tube, Standard Ambient Temperature,
H Aluminum Pre-Coat Fin/Copper Tube, Standard Ambient
Temperature, Compressor Enclosures
J Aluminum E-Coated Fin/Copper Tube, Standard Ambient
Temperature, Compressor Enclosures
- Aluminum Fin/Copper Tube, High Ambient Temperature
0 Copper Fin/Copper Tube, High Ambient Temperature
1 Aluminum Pre-Coat Fin/Copper Tube, High Ambient Temperature
2 Aluminum E-Coat Fin/Copper Tube, High Ambient Temperature
3 Copper E-Coat Fin/Copper Tube, High Ambient Temperature
4 Micro Channel Heat Exchanger (MCHX), High Ambient
Temperature
7 Copper Fin/Copper Tube, High Ambient Temperature, Low Sound
B Copper E-Coat Fin/Copper Tube, High Ambient Temperature,
Low Sound
C MCHX, High Ambient Temperature, Low Sound
G Copper Fin/Copper Tube, Standard Ambient Temperature,
Low Sound
K Copper E-Coat Fin/Copper Tube, Standard Ambient Temperature,
Low Sound
L MCHX, Standard Ambient Temperature, Low Sound
N Aluminum Fin/Copper Tube, Standard Ambient Temperature
P Copper Fin/Copper Tube, Standard Ambient Temperature
Q Aluminum Pre-Coat Fin/Copper Tube, Standard Ambient
Temperature
R Aluminum E-Coat Fin/Copper Tube, Standard Ambient
Temperature
S Copper E-Coat Fin/Copper Tube, Standard Ambient Temperature
T MCHX, Standard Ambient Temperature
Electrical Options
- Single Point Power, XL, Terminal Block, No Control Transformer
0 Single Point Power, Wye-Delta, Terminal Block, No Control Transformer
3 Dual Point Power, XL, Terminal Block, No Control Transformer
4 Dual Point Power, Wye-Delta, Terminal Block, No Control Transformer
7 Single Point Power, XL, Disconnect, No Control Transformer
8 Single Point Power, Wye-Delta, Disconnect, No Control Transformer
C Dual Point Power, XL, Disconnect, No Control Transformer
D Dual Point Power, Wye-Delta, Disconnect, No Control Transformer
H Single Point Power, XL, Terminal Block, Control Transformer
J Single Point Power, Wye-Delta, Terminal Block, Control Transformer
M Dual Point Power, XL, Terminal Block, Control Transformer
N Dual Point Power, Wye-Delta, Terminal Block, Control Transformer
R Single Point Power, XL, Disconnect, Control Transformer
S Single Point Power, Wye-Delta, Disconnect, Control Transformer
W Dual Point Power, XL, Disconnect, Control Transformer
X Dual Point Power, Wye-Delta, Disconnect, Control Transformer
Hydronic Pump Package Options

- None
1 Single Pump, 5 HP
2 Single Pump, 7.5 HP
3 Single Pump, 10 HP
4 Single Pump, 15 HP
7 Dual Pump, 5 HP
8 Dual Pump, 7.5 HP
B Dual Pump, 10 HP
C Dual Pump, 15 HP
Refrigeration Circuit Options

- None
1 Suction Service Valves
2 Low Ambient Temperature Head Pressure Control
5 Suction Service Valves, Low Ambient Temperature Head Pressure Control
Cooler/Brine Options
0 Integral Cooler
3 Integral Cooler, Minus One Pass
5 Integral Cooler, Plus One Pass
B Integral Cooler, Brine
F Integral Cooler, Minus One Pass, Brine
H Integral Cooler, Plus One Pass, Brine
EMM
LON
XL
a30-4401
LEGEND
Energy Management Module
Local Operating Network
Across-the-Line Starter
Fig. 1 AquaForce Chiller Model Number Designation
MOUNTING PLATE
0.875 DIA.[22.2]
MOUNTING HOLE
1.50 DIA. [38.1]

RIGGING HOLE
7.88
[200]
3.93
[100]
1.31
[33]
1.75
[44]
DETAIL "A"
5.0
[127]
MOUNTING PLATE
CONTACT SURFACE
TYPICAL 4 PLACES
109.0
[2769]
Cooler Tube
Service Area
5.83 [148]
26.5
[673]
Control Box All Voltages

4.15
[105]
65.73
[1670]
Fig. 2 30XA080 Air-Cooled Liquid Chiller Dimensions
NOTES:
1. Unit must have clearances as follows:
Top Do not restrict
Sides and Ends 6 ft from solid surface.
2. Temperature relief devices are located on liquid line and economizer assemblies and have 1/4-in. flare connection.
3. 3/8-in. NPT vents and drains located in each cooler head at each
end of cooler.
4. Drawing depicts unit with standard two-pass cooler. Refer to the
Packaged Chiller Builder program for other configurations.
5. Dimensions are shown in inches; dimensions in brackets are in
millimeters.
a30-4402
TOP VIEW
121.17
[3078]
141.22
[3587]
7/8" knockouts for main power entry

(7.48" [190mm] hole spacing)
Piping Entrance
43.85
[1114]
68.06
[1729]
88.04
[2236]
22.2
[565]
41.1
[1044]
Display
Location
(380,460,575v)
Control Box
All Voltages
Optional Non-fused
Disconnect Handle
a30-4403
26.51
[673]
88.04
[2236]
Control
power entry
3.35
[85]
16.1
[409]
8.9
[226]
49.85
[1266]
90.55
[2300]
Display
Location
(200,230v)
FRONT VIEW
109.03
121.17 [2769]
[3078] 141.22
[3587]
90.55
[2300]
3/4 NPT Relief

Conn. Female
5" Victaulic
Entering Water
5" Victaulic
Leaving Water
19.06
10.8 [484]
[274]
19.06
[484] 10.8
[274]
5" Victaulic Entering Water
5" Victaulic Leaving Water
Fig. 2 30XA080 Air-Cooled Liquid Chiller Dimensions (cont)
Mounting Holes
Rigging Holes
(See Detail A)
Cooler Drain
3/8 NPT
Cooler Vent
3/8 NPT
LEFT END VIEW
53.92
[1370]

RIGHT END VIEW
88.04
[2236]
68.06
[1729]
90.55
[2300]
1.50 DIA. [38.1]

RIGGING HOLE
MOUNTING
PLATE
0.875 DIA. [22.2]

MOUNTING HOLE
7.88
[200]
3.93
[100]
1.31
[33]
1.75
[44]
DETAIL "A"
5.0
[127]
MOUNTING PLATE
CONTACT SURFACE
TYPICAL 4 PLACES
4.15
[105]
A
44.11 [1120]
44.11 [1120]
44.11 [1120]
44.11 [1120]
5.51 [140]
30XA UNIT
090
100
110
120
109.0
[2769]
Cooler Tube
Service Area
26.51
[673]
134.73
[3422]
B
86.93 [2208]
87.22 [2215]
87.62 [2226]
87.12 [2213]
188.2
[4780]
TOP VIEW
157.54
[4002]

Fig. 3 30XA090-120 Air-Cooled Liquid Chiller Dimensions
NOTES:
Top Do not restrict
2. Temperature relief devices are located on liquid line and economizer assemblies and have 1/4-in. flare connection.
3. 3/8-in. NPT vents and drains located in each cooler head at each end of cooler.
4. Drawing depicts unit with single-point power and standard two-pass cooler.
Refer to the Packaged Chiller Builder program for other configurations.
5. Dimensions are shown in inches; dimensions in brackets are in millimeters.
a30-4404
Piping
Entrance
85.56
[2173]
88.04
[2236]
88.28
[2242]
22.2
[565]
41.1
[1044]
Display
Location
(380,460,575v)
Control Box
All Voltages
Optional Non-fused
Disconnect Handle
a30-4405
26.51
[673]
88.04
[2236]
88.28
[2242]
Control
power entry
10.27
[261]
16.1
[409]
8.9
[226]
157.54
[4002]
78.02
[1982]
134.73
[3422]
78.02
[1982]
FRONT VIEW
188.2
[4780]
19.06
[484]
10.27
[261]
Drain
in
3/4 NPT Relief Conn. Female
Fig. 3 30XA090-120 Air-Cooled Liquid Chiller Dimensions (cont)
Mounting Holes
Rigging Holes
(See Detail A)
Cooler Drain
3/8 NPT
Cooler Vent
3/8 NPT
19.06
[484]
90.55
[2300]
49.85
[1266]
Display
Location
(200,230v)
LEFT END VIEW
85.56
[2173]
53.92
[1370]

85.56
[2173]
19.06
[484]
10.27
[261]
90.55
[2300]
RIGHT END VIEW
88.28
[2242]
88.04
[2236]
90.55
[2300]
A
44.63 [1134]
44.61 [1133]
10.58
[269]
22.02
[559] 21.28
[541]
5" Victaulic
Leaving Water
5" Victaulic
Entering Water
30XA UNIT
140
160
89.36
[2270]
85.61
[2174]
Control Box
23.62
[600]
5.84 [148]
Display Location
109.0
[2769]
135.06
[3431]
TOP VIEW
235.24
[5975]
235.24
[5975]
BACK VIEW
163.87
[4162]

for 380,460,575v (5.55 [141 mm] hole
spacing)
2.83 [72]
7.23 [182]
Control Box, incoming

power supply
(200,230v)
Fig. 4 30XA140,160 Air-Cooled Liquid Chiller Dimensions
90.55
[2300]
Cooler Tube
Service Area
RIGHT END VIEW
88.04
[2236]
B
115.88 [2943]
115.64 [2937]
NOTES:
Top Do not restrict
2. Temperature relief devices are located on liquid line and economizer assemblies and have
1/ -in. flare connection.
4
3. 3/8-in. NPT vents and drains located in each
cooler head at each end of cooler.
4. Drawing depicts unit with standard condenser
fans, and standard two-pass cooler. Refer to
the Packaged Chiller Builder program for
other configurations.
5. Dimensions are shown in inches; dimensions
in brackets are in millimeters.
a30-4406
1.58
[2834]
74
[1880]
Control Box
(200/230V)
28.81
[732]
90.55
[2300]
89.36
[2270]
85.61
[2174]
88.04
[2236]
Piping Entrance
Control power entry (all voltages)
Non-fused
Disconnect Handle
for 380, 460, 575 v
Control Box
(all voltages)
Control Box
a30-4407
22.2
[565]
Control Box
(200,230,380,
460,575v)
7/8" knockouts for

main power entry
(5.55" [141 mm]
hole spacing)
41.1
[1044]
Optional Non-fused
Disconnect Handle
Control Box
(200,230v)
12.7
[3.23]
88.04
[2236] 89.36
[2270]
1.50 DIA. [38.1]

RIGGING HOLE
Mounting Holes
Rigging Holes
(See Detail A)
Cooler Drain
3/8 NPT
Cooler Vent
3/8 NPT
MOUNTING PL ATE
0.875 DIA. [22.2]

MOUNTING HOLE
21.28
[541]
90.55
[2300]
Control Box
incoming power
supply (200,230v)
7.88
[200]
7.2
[182]
2.8 [72]
16.1
[409]
135.03
[3431]
3.93
[100]
1.31
[33]
1.75
[44]
163.87
[4162]
121.49
[3086]
33.96
[863]
out
DETAIL "A"
FRONT VIEW
235.24
[5975]
MOUNTING PLATE
CONTACT SURFACE
TYPICAL 4 PLACES
5.0
[127]
109.03
[2769]
Fig. 4 30XA140,160 Air-Cooled Liquid Chiller Dimensions (cont)
LEFT END VIEW
42.8
[1087]
2.5
[63.5]
8.9
[226]
Drain
58.08
[1475]
21.28 22.02
[541] [559]

in
90.55
[2300]
10
A
46.12 [1171]
46.15 [1172]
22.48
[571]
11.3
[287]
6" Victaulic
Entering Water
6" Victaulic
Leaving Water
30XA UNIT
180
200
12.7
[323]
Cooler Tube
Service Area
RIGHT END VIEW
70.16
[1782]
88.04
[2236]
B
143.04 [3633]
142.97 [3631]
NOTES:
Top Do not restrict
2. Temperature relief devices are located on
liquid line and economizer assemblies and
have 1/4-in. flare connection.
3
3. /8-in. NPT vents and drains located in
each cooler head at each end of cooler.
4. Drawing depicts unit with standard condenser fans, and standard two-pass
cooler. Refer to the Packaged Chiller
Builder program for other configurations.
a30-4408
23.62
[600]
B
177.65
[4512]
BACK VIEW
282.2
[7168]
Control Box
(all voltages)
TOP VIEW
282.22
[7168]
Control Box
(380,460,575v)
90.55
[2300]
7/8" knockouts for main power entry 380, 460, 575v

(5.55" [141 mm] hole spacing)
61.6
109.39 [1565]
[2779]
Control Box, incoming

power supply
(200,230v)
158.6
[4028]
120.73
[3067]
Optional Non-fused
Disconnect Handle
for 380, 400, 575v
Control power entry

(all voltages)
Control Box
Display Location
70.16
[1782]
88.04
[2236]
Control Box
(200,230v incoming
power supply connection)
28.81
[732]
90.55
[2300]
Piping Entrance
22.2
[565]
41.1
[1044]
Optional Non-fused
Disconnect Handle
Control Box
(200,230v)
7/8" knockouts for
main power entry
(5.55" [141 mm]
hole spacing)
Control Box
(200,230,380,
460,575v)
a30-4174
11
12.7
[323]
88.04
[2236]
LEFT END VIEW
42.8
[1087]
2.5
[63.5]
7.88
[200]
18.7
[489]
58.08
[1475]
Cooler Drain
3/8 NPT
3.93
[100]
1.31
[33]
1.75
[44]
177.65
[4512]
DETAIL "A"
FRONT VIEW
282.22
[7168]
78.02
[1982]
MOUNTING PLATE
CONTACT SURFACE
TYPICAL 4 PLACES
5.0
[127]
33.97
[863]
3/4 NPT Relief

Conn. Female
MOUNTING PLATE
0.875 DIA.[22.2]
MOUNTING HOLE
1.50 DIA. [38.1]

RIGGING HOLE
Mounting Holes
Rigging Holes
(See Detail A)
90.55
[2300]
Control Box,
incoming Power
Supply (200,
230v)
Cooler Vent
3/8 NPT
78.02
[1982]
11.3
[287]
22.48
[571]
90.55
[2300]
12
22.48
[571]
11.3
[287]
70.16
[1782]
88.04
[2236]
12.7
[323]
B
171.42 [4354]
170.83 [4339]
RIGHT END VIEW
A
46.17 [1173]
46.23 [1174]
6" Victaulic
Leaving Water
6" Victaulic
Entering Water
30XA UNIT
220
240
NOTES:
Top Do not restrict
1/4-in. flare connection.
4. Drawing depicts unit with standard condenser
fans, and standard two-pass cooler. Refer to
the Packaged Chiller Builder program for other
configurations.
a30-4409
224.65 [5706]
Control Box
(200,230,380,
460,575v)
Incoming power, 380,460,575v
BACK VIEW
329.26 [8363]
167.73 [4260]
70.16
[1782]
Optional Non-fused
Disconnect Handle
88.04
[2236]
Piping Entrance
Control Power Entry (all voltages)
Control Box
(200/230v only)
140.14 [3560]
Control Box
205.6 [5222]
Display Location
TOP VIEW
Incoming power
(200,230v)
329.26 [8363]
Control
Box
28.81 23.62
[732] [600]
90.55
[2300]

108.6 [2758]
Cooler Tube
Service Area
Control Box (200,230v)
90.55
[2300]
Control
Boxes
a30-4176
13
LEFT END VIEW
88.04 [2236]
58.08 [1475]
Cooler Drain
3/8 NPT
1.50 DIA. [38.1]

RIGGING HOLE
18.07
[459]
7.88
[200]
3.93
[100]
1.31
[33]
1.75
[44]
224.65 [5706]
33.97 [863]
5.0
[127]
MOUNTING PLATE
CONTACT SURFACE
TYPICAL 4 PLACES
DETAIL "A"
FRONT VIEW
329.26 [8363]
109.03 [2769]
33.96 [863]
MOUNTING PLATE
0.875 DIA.[22.2]
MOUNTING HOLE
Mounting Holes
Rigging Holes
(See Detail A)
90.55
[2300]
Cooler Vent
3/8 NPT
58.08 [1475]
11.3
[287]
22.48
[571]
90.55
[2300]
14
23.63
[600]
12.21
[310]
8" Victaulic
Entering Water
8" Victaulic
Leaving Water
30XA UNIT
260
280
300
B
216.16 [5490]
215.86 [5483]
216.18 [5491]
RIGHT END VIEW
88.04 [2236]
71.06 [1805]
A
44.22 [1123]
44.30 [1125]
44.32 [1126]
NOTES:
1. Unit must have clearances as
follows:
Top Do not restrict
Sides and Ends 6 ft from solid
surface.
2. Temperature relief devices are
located on liquid line and economizer assemblies and have 1/4-in.
flare connection.
3. 3/8-in. NPT vents and drains
located in each cooler head at
each end of cooler.
4. Drawing depicts unit with standard
condenser
fans
and
standard two-pass cooler. Refer
to the Packaged Chiller Builder
program for other configurations.
5. Dimensions are shown in inches;
dimensions in brackets are in
millimeters.
a30-4177
Control Box
Incoming power
(all voltages)
304.71 [7740]
Display Location
BACK VIEW
199.7 [5072]
245.52 [6236]
71.06
[1805] 88.04
[2236]
Piping Entrance
Control Power Entry (all voltages)
Control Box (all voltages)
Optional Non-fused
Disconnect Handle
376.2 [9555]
TOP VIEW
376.2 [9555]
Fig. 7 30XA260-300 Air-Cooled Liquid Chiller Dimensions
28.81 23.62
[732] [600]
90.55
[2300]

188.35 [4784]
B
Cooler Tube
Service Area
Control Box,
incoming power supply
90.55
[2300]
LEFT END VIEW
88.04 [2236]
Control Box
All Voltages
15.77 [401]
a30-4178
15
Mounting Holes
Rigging Holes
(See Detail A)
90.55
[2300]
0.875 DIA.[22.2]
MOUNTING HOLE
1.50 DIA. [38.1]

RIGGING HOLE
78.02 [1982]
7.88
[200]
376.2 [9555]
31.96 [812]
3.93
[100]
1.31
[33]
78.02 [1982]
5.0
[127]
MOUNTING PLATE
CONTACT SURFACE
TYPICAL 4 PLACES
DETAIL "A"
FRONT VIEW
1.75
[44]
304.71 [7740]
78.02 [1982]
Fig. 7 30XA260-300 Air-Cooled Liquid Chiller Dimensions (cont)
MOUNTING PLATE
16.1
[409]
Cooler Drain
3/8 NPT
Cooler Vent
3/8 NPT
78.02 [1982]
12.21
[310]
23.63
[600]
90.55
[2300]
16
23.63
[600]
12.21
[310]
8" Victaulic
Entering Water
88.04 [2236]
71.06 [1805]
A
42.92 [1090]
42.92 [1090]
Control Box
90.55
[2300]
232.66 [5910]
B
Control Box, incoming power supply
BACK VIEW
246.7 [6267]
292.56 [7431]
Optional Non-fused
Disconnect Handle
Display Location
Control power entry
Control Box
423.24 [10750]
TOP VIEW
423.24 [10750]
349.02 [8865]
Cooler Tube
Service Area
28.81
23.62
[732] [600]

B
246.16 [6252]
246.72 [6267]
RIGHT END VIEW
30XA UNIT
325
350
NOTES:
Top Do not restrict
4. Drawing depicts unit with standard condenser fans and standard two-pass cooler.
Refer to the Packaged Chiller Builder program for other configurations.
8" Victaulic
Leaving Water
a30-4410
71.06
[1805]
88.04
[2236]
Piping Entrance
90.55
[2300]
Control Box
a30-4180
17
LEFT END VIEW
15.77 [401]
88.04 [2236]
90.55
[2300]
1.50 DIA. [38.1]

RIGGING HOLE
Mounting Holes
Rigging Holes
(See Detail A)
109.03
[2769]
7.88
[200]
33.96
[863]
3.93
[100]
1.31
[33]
1.75
[44]
78.02
[1982]
5.0
[127]
MOUNTING PLATE
CONTACT SURFACE
TYPICAL 4 PLACES
DETAIL "A"
FRONT VIEW
33.97
58.08 [1475]
[863]
349.02
[8865]
423.24
[10750]
MOUNTING PLATE
0.875 DIA.[22.2]
MOUNTING HOLE
16.1
[409]
Cooler Drain
3/8 NPT
Cooler Vent
3/8 NPT
78.02
[1982]
12.21
[310]
23.63
[600]
90.55
[2300]
18
17.92
[455]
8" Victaulic
Entering Water
RIGHT END VIEW
88.04 [2236]
72.1 [1831]
Piping Entrance
Control Box #1
Circuit 1
BACK VIEW
470.22 [11944]
Optional Non-fused
Disconnect Handles
TOP VIEW
470.22 [11944]
Piping Entrance
53.29 [1354]
63.35 [1609]
119.07 [3024]
Circuit 2
70.02
[1779]
Cooler Tube
Service Area
105.7 [2684]
151.5 [3848]
28.81
[732]
Control power entry
Display Location
Control Box #2
7/8" Knockouts for Ckt 2 power

(5.55" between holes)
240.69 [6114]
331.58 [8422]
378.95 [9625]
Control Box #2
Fig. 9 30XA400 Air-Cooled Liquid Chiller Dimensions
23.62
[600]
Control Box #1

45.79
[1163]
72.1
88.04 [1831]
[2236]
Control
Box
90.55
[2300]
NOTES:
Top Do not restrict
1/ -in. flare connection.
4
4. Drawing depicts unit with dual-point power
standard condenser fans and standard onepass cooler. Refer to the Packaged Chiller
Builder program for other configurations.
5. Actual cooler consists of two separate coolers
piped in series at the factory. Piping may be
split for rigging.
a30-4181
90.55
[2300]
Control
Boxes
a30-4182
19
LEFT END VIEW
70.02 [1779]
88.04 [2236]
15.77 [401]
78.02 [1982]
78.02 [1982]
3.93
[100]
1.31
[33]
1.75
[44]
5.0
[127]
MOUNTING PLATE
CONTACT SURFACE
TYPICAL 4 PLACES
DETAIL "A"
FRONT VIEW
378.95 [9625]
470.22 [11944]
31.96
[812]
Fig. 9 30XA400 Air-Cooled Liquid Chiller Dimensions (cont)
MOUNTING PLATE
7.88
[200]
16.1
78.02 [1982]
[409]
53.29 [1354]
1.50 DIA. [38.1]

RIGGING HOLE
17.92
[455]
0.875 DIA.[22.2]
MOUNTING HOLE
Mounting Holes
Rigging Holes
(See Detail A)
17.92
[455]
90.55
[2300]
78.02 [1982]
33.93
[862]
58.08 [1475]
17.92
[455]
90.55
[2300]
Cooler Drain 3/8 NPT

located in cooler heads
Cooler Vent 3/8 NPT

20
RIGHT END VIEW
88.04 [2236]
73.0
88.04 [1854]
[2236]
Piping Entrance
Control
Boxes
90.55
[2300]
Control Box #1
Circuit 1
426.0 [10820]
BACK VIEW
517.26 [13138]
Circuit 2
Control power entry
Display Location
Control Box #2

83.62 [2124]
93.68 [2379]
129.1 [3279]
Cooler Tube
Service Area
152.7 [3879]
198.54 [5043]
Piping Entrance
378.62 [9617]
Non-fused Disconnect Handles
TOP VIEW
517.26 [13138]
Control Box #2
23.62
[600]
Control Box #1

B
264.7 [6723]
263.99 [6705]
73.0 [1854]
A
44.71 [1136]
44.78 [1137]
17.92
[455]
8" Victaulic
Entering Water
30XA UNIT
450
500
NOTES:
Top Do not restrict
3
3. /8-in. NPT vents and drains located in
each cooler head at each end of cooler.
4. Drawing depicts unit with dual-point power
standard condenser fans and standard
one-pass cooler. Refer to the Packaged
Chiller Builder program for other configurations.
5. Actual cooler consists of two separate
coolers piped in series at the factory. Piping may be split for rigging.
a30-4183
28.81
[732]
71.06
[1805]
90.55
[2300]
Control
Boxes
a30-4184
21
LEFT END VIEW
71.06 [1805]
88.04 [2236]
15.77 [401]
17.92
[455]
17.92
[455]
1.50 DIA. [38.1]

RIGGING HOLE
58.08
18.07
[1475]
[459]
83.62 [2124]
7.88
[200]
109.03
[2769]
58.08
[1475]
3.93
[100]
1.31
[33]
1.75
[44]
5.0
[127]
MOUNTING PLATE
CONTACT SURFACE
TYPICAL 4 PLACES
DETAIL "A"
FRONT VIEW
426.0 [10820]
517.26 [13138]
33.96
[863]
33.97
[863]
MOUNTING PLATE
33.97
[863]
0.875 DIA.[22.2]
MOUNTING HOLE
90.55
[2300]
Mounting Holes
Rigging Holes
(See Detail A)
78.02
[1982]
78.02
[1982]
17.92
[455]
90.55
[2300]
Cooler Drain 3/8 NPT

Cooler Vent 3/8 NPT

UNITS WITHOUT PUMPS ENGLISH

30XA
UNIT SIZE
080
30XA
UNIT SIZE
090
100
110
120
30XA
UNIT SIZE
140
160
30XA
UNIT SIZE
180
200
30XA
UNIT SIZE
220
240
260
280
300
30XA
UNIT SIZE
325
350
30XA
UNIT SIZE
400
450
500
MOUNTING WEIGHT (lb)

MCHX CONDENSER COILS
A
B
C
D
Total
1947
1673
1670
1943
7234
MOUNTING WEIGHT (lb) MCHX CONDENSER COILS
A
B
C
D
E
F
Total
1201
2043
750
951
1983
1199
8127
1226
2098
780
981
2038
1224
8348
1239
2136
798
1006
2075
1229
8483
1272
2174
800
1007
2106
1263
8622
A
B
C
D
E
F
G
H
Total
1897
1444
864
1181
1217
883
1584
1699 10,768
1949
1469
878
1206
1246
899
1603
1750 11,000
A
B
C
D
E
F
G
H
I
J
Total
905
1484
1164
1849
1187
1224
1868
840
1289
888
12,699
909
1499
1188
1870
1192
1232
1879
848
1299
893
12,810
A
B
C
D
E
F
G
H
I
J
K
L
813
1196
1592
1498
828
1216
1259
848
1363
1064
1237
832
829
1218
1617
1520
830
1218
1261
850
1371
1073
1260
849
495
1431
1630
763
2465
1013
1528
2380
800
1333
1386
495
497
1451
1663
771
2497
1015
1530
2390
803
1358
1406
497
502
1465
1686
786
2568
1027
1557
2454
811
1367
1417
502
A
B
C
D
E
F
G
H
I
J
K
L
742
742
978
1531
783
2546
1067
1563
2334
804
1646
1247
745
745
982
1546
792
2598
1077
1589
2386
808
1651
1249
A
B
C
D
E
F
G
H
I
J
K
L
847
1234
1511
2965
1255
789
2214
1071
1566
2286
747
1265
856
1179
2160
2282
905
1057
2030
2053
2711
1934
1551
1266
843
1236
2207
2334
909
1060
2037
2060
2718
1941
1555
1269
Total
13,748
13,897
15,720
15,878
16,141
M
742
745
N
742
745
Total
17,467
17,659
M
2152
1440
1457
N
991
1385
1401
O
1277
1216
1279
M
337
338
N
337
338
Total
7923
8010
M
976
653
661
N
450
628
635
O
579
551
580
P
868
876
863
Total
23,038
24,901
25,167
P
394
397
391
Total
10 450
11 295
11 416
UNITS WITHOUT PUMPS SI

30XA
UNIT SIZE
080
30XA
UNIT SIZE
090
100
110
120
30XA
UNIT SIZE
140
160
30XA
UNIT SIZE
180
200
30XA
UNIT SIZE
220
240
260
280
300
30XA
UNIT SIZE
325
350
30XA
UNIT SIZE
400
450
500
MOUNTING WEIGHT (kg)

MCHX CONDENSER COILS
A
B
C
D
Total
883
759
758
882
3281
MOUNTING WEIGHT (kg) MCHX CONDENSER COILS
A
B
C
D
E
F
Total
545
927
340
431
899
544
3686
556
952
354
445
924
555
3786
562
969
362
456
941
558
3848
577
986
363
457
955
573
3911
A
B
C
D
E
F
G
H
Total
860
655
392
536
552
401
719
771
4884
884
666
398
547
565
408
727
794
4990
A
B
C
D
E
F
G
H
I
J
Total
410
673
528
839
538
555
847
381
584
403
5760
412
680
539
848
541
559
852
385
589
405
5811
A
B
C
D
E
F
G
H
I
J
K
L
369
542
722
680
376
552
571
385
618
483
561
378
376
552
734
690
377
553
572
386
622
487
572
385
225
649
740
346
1118
460
693
1079
363
605
629
225
225
658
754
350
1133
461
694
1084
364
616
638
225
228
664
765
357
1165
466
706
1113
368
620
643
228
A
B
C
D
E
F
G
H
I
J
K
L
337
337
444
695
355
1155
484
709
1058
365
746
565
338
338
446
701
359
1179
488
721
1082
367
749
567
A
B
C
D
E
F
G
H
I
J
K
L
384
560
685
1345
569
358
1004
486
710
1037
339
574
388
535
980
1035
411
479
921
931
1230
877
704
574
382
561
1001
1059
412
481
924
934
1233
880
705
576
Total
6236
6304
7130
7202
7322
Fig. 11A Unit Mounting Weights (Units with MCHX Condenser Coils)
22
30XA220-300
30XA080
COOLER SIDE
B
COOLER SIDE
D
C
a30-4419
a30-4423
J
K
H
I
COMPRESSOR SIDE
COMPRESSOR SIDE
30XA325-350
30XA090-120
COOLER SIDE
C
COOLER SIDE
E
D
C
a30-4424
a30-4420
E
COMPRESSOR SIDE
J
I
K
L
COMPRESSOR SIDE
30XA400-500
30XA140,160
COOLER SIDE
C
B
COOLER SIDE
E
D
C
a30-4425
a30-4421
COMPRESSOR SIDE
30XA180-200
E
L
M
N
COMPRESSOR SIDE
LEGEND
MCHX Micro-Channel Heat Exchanger
COOLER SIDE
C
a30-4422
COMPRESSOR SIDE
Fig. 11A Unit Mounting Weights (Units with MCHX Condenser Coils) (cont)
23
SINGLE PUMP UNITS ENGLISH

30XA
UNIT SIZE
090
100
110
120
30XA
UNIT SIZE
140
160

A
B
C
D
E
F
Total
1201
2754
1087
900
1944
1199
9085
1226
2814
1123
924
1995
1224
9306
1239
2855
1145
945
2027
1229
9441
1272
2893
1147
947
2059
1263
9580
A
B
C
D
E
F
G
H
1897
1444
1609
1606
1078
810
1584
1699
1949
1469
1626
1635
1103
824
1603
1750
Total
11,726
11,958
SINGLE PUMP UNITS SI

30XA
UNIT SIZE
090
100
110
120
30XA
UNIT SIZE
140
160

A
B
C
D
E
F
Total
545
1249
493
408
882
544
4121
556
1276
510
419
905
555
4221
562
1295
519
429
920
558
4282
577
1312
520
430
934
573
4346
A
B
C
D
E
F
G
H
860
655
730
728
489
367
719
771
884
666
737
742
500
374
727
794
30XA090-120
30XA140,160
COOLER SIDE
C
Total
5319
5424
COOLER SIDE
C
B
a30-4420
a30-4421
MCHX
E
COMPRESSOR SIDE
COMPRESSOR SIDE
LEGEND
Micro-Channel Heat Exchanger
24
DUAL PUMP UNITS ENGLISH

30XA
UNIT SIZE
090
100
110
120
30XA
UNIT SIZE
140
160

A
B
C
D
E
F
Total
1201
2962
1176
900
1944
1199
9382
1226
3022
1212
924
1995
1224
9603
1239
3064
1234
945
2027
1229
9738
1272
3101
1236
947
2059
1263
9877
A
B
C
D
E
F
G
H
1897
1444
1818
1694
1078
810
1584
1699
1949
1469
1834
1724
1103
824
1603
1750
Total
12,023
12,255
DUAL PUMP UNITS SI

30XA
UNIT SIZE
090
100
110
120
30XA
UNIT SIZE
140
160

A
B
C
D
E
F
Total
545
1343
533
408
882
544
4255
556
1371
550
419
905
555
4356
562
1390
560
429
920
558
4417
577
1407
560
430
934
573
4480
A
B
C
D
E
F
G
H
860
655
825
769
489
367
719
771
884
666
832
782
500
374
727
794
30XA090-120
30XA140,160
COOLER SIDE
C
Total
5454
5559
COOLER SIDE
C
B
a30-4420
a30-4421
MCHX
E
COMPRESSOR SIDE
COMPRESSOR SIDE
LEGEND
Micro-Channel Heat Exchanger
25

30XA
UNIT SIZE
080
30XA
UNIT SIZE
090
100
110
120
30XA
UNIT SIZE
140
160
30XA
UNIT SIZE
180
200
30XA
UNIT SIZE
220
240
260
280
300
30XA
UNIT SIZE
325
350
30XA
UNIT SIZE
400
450
500
MOUNTING WEIGHT (lb) Al/Cu*

A
B
C
D
Total
2059
1785
1778
2051
7674
A
B
C
D
E
F
Total
1273
2188
822
1023
2127
1271
8704
1299
2244
853
1054
2184
1297
8931
1312
2284
872
1079
2222
1303
9071
1346
2322
874
1082
2255
1337
9216
A
B
C
D
E
F
G
H
Total
2007
1554
938
1254
1291
957
1695
1809 11,505
2061
1581
953
1281
1321
974
1715
1862 11,748
A
B
C
D
E
F
G
H
I
J
Total
979
1558
1239
1998
1261
1298
2016
915
1363
962
13,590
984
1574
1263
2020
1267
1308
2029
923
1375
968
13,712
A
B
C
D
E
F
G
H
I
J
K
883
1266
1697
1603
898
1286
1329
918
1468
1169
1307
900
1288
1723
1626
901
1289
1331
921
1477
1179
1331
566
1572
1701
834
2607
1084
1599
2521
871
1404
1528
569
1594
1734
843
2640
1087
1601
2533
875
1429
1549
578
1617
1762
862
2720
1103
1633
2607
887
1444
1570
A
B
C
D
E
F
G
H
I
J
K
856
856
1054
1607
859
2697
1143
1639
2485
880
1722
860
860
1059
1623
869
2752
1153
1666
2539
885
1727
A
B
C
D
E
F
G
H
I
J
K
924
1311
1588
3119
1332
866
2368
1148
1643
2440
824
933
1256
2276
2398
982
1134
2184
2207
2866
2089
1629
921
1314
2325
2452
987
1139
2194
2217
2875
2098
1633
L
902
920
566
569
578
Total
14,727
14,887
16,853
17,022
17,362
L
1322
1326
M
856
860
N
856
860
Total
18,834
19,040
L
1342
1343
1348
M
2306
1556
1575
N
1069
1501
1519
O
1354
1293
1357
L
409
417
257
258
262
Total
6680
6753
7644
7721
7876
L
600
601
M
388
390
N
388
390
Total
8543
8636
L
609
609
611
M
1046
706
714
N
485
681
689
O
614
586
616
P
945
953
941
Total
24,578
26,600
26,894
P
428
432
427
Total
11 149
12 066
12 199
*Condenser Coil: Aluminum Fins/Copper Tubing.

30XA
UNIT SIZE
080
30XA
UNIT SIZE
090
100
110
120
30XA
UNIT SIZE
140
160
30XA
UNIT SIZE
180
200
30XA
UNIT SIZE
220
240
260
280
300
30XA
UNIT SIZE
325
350
30XA
UNIT SIZE
400
450
500
MOUNTING WEIGHT (kg) Al/Cu*

A
B
C
D
Total
934
810
807
930
3481
A
B
C
D
E
F
Total
578
992
373
464
965
576
3948
589
1018
387
478
991
588
4051
595
1036
396
489
1008
591
4115
611
1053
397
491
1023
607
4181
A
B
C
D
E
F
G
H
Total
910
705
425
569
585
434
769
821
5219
935
717
432
581
599
442
778
845
5329
A
B
C
D
E
F
G
H
I
J
Total
444
707
562
906
572
589
915
415
618
436
6164
446
714
573
916
575
593
920
419
624
439
6220
A
B
C
D
E
F
G
H
I
J
K
401
574
770
727
407
583
603
416
666
530
593
408
584
782
738
409
585
604
418
670
535
604
257
713
772
378
1182
492
725
1144
395
637
693
258
723
787
382
1197
493
726
1149
397
648
703
262
734
799
391
1234
501
741
1182
402
655
712
A
B
C
D
E
F
G
H
I
J
K
388
388
478
729
390
1224
518
744
1127
399
781
390
390
480
736
394
1248
523
756
1152
401
784
A
B
C
D
E
F
G
H
I
J
K
419
595
720
1415
604
393
1074
521
745
1107
374
423
570
1032
1088
446
514
991
1001
1300
948
739
418
596
1055
1112
448
516
995
1005
1304
952
741
*Condenser Coil: Aluminum Fins/Copper Tubing.
Fig. 11B Unit Mounting Weights (Units with Al/Cu Condenser Coils)
26
30XA220-300
30XA080
COOLER SIDE
B
COOLER SIDE
D
C
a30-4419
a30-4423
J
K
H
I
COMPRESSOR SIDE
COMPRESSOR SIDE
30XA325-350
30XA090-120
COOLER SIDE
C
COOLER SIDE
E
D
C
a30-4424
a30-4420
E
COMPRESSOR SIDE
J
I
K
L
COMPRESSOR SIDE
30XA400-500
30XA140,160
COOLER SIDE
C
B
COOLER SIDE
E
D
C
a30-4425
a30-4421
COMPRESSOR SIDE
L
M
N
COMPRESSOR SIDE
30XA180-200
E
COOLER SIDE
C
a30-4422
COMPRESSOR SIDE
Fig. 11B Unit Mounting Weights (Units with Al/Cu Condenser Coils) (cont)
27

30XA
UNIT SIZE
090
100
110
120
30XA
UNIT SIZE
140
160

B
C
D
E
F
Total
2898
1160
972
2089
1271
9,662
2959
1196
997
2140
1297
9,889
3002
1219
1019
2175
1303 10,029
3041
1221
1021
2208
1337 10,174
B
C
D
E
F
G
1554
1683
1679
1152
883
1695
1581
1701
1710
1178
898
1715
A
1273
1299
1312
1346
A
2007
2061
H
1809
1862
Total
12,463
12,706
H
821
845
Total
5653
5763

30XA
UNIT SIZE
090
100
110
120
30XA
UNIT SIZE
140
160

B
C
D
E
F
Total
1314
526
441
947
576
4383
1342
543
452
971
588
4485
1362
553
462
986
591
4549
1379
554
463
1001
607
4615
B
C
D
E
F
G
705
763
762
523
401
769
717
771
776
534
408
778
A
578
589
595
611
A
910
935
Condenser Coil: Copper Fins/Copper Tubing.
30XA090-120
30XA140,160
COOLER SIDE
C
COOLER SIDE
C
B
a30-4420
a30-4421
E
COMPRESSOR SIDE
COMPRESSOR SIDE
28

30XA
UNIT SIZE
090
100
110
120
30XA
UNIT SIZE
140
160

B
C
D
E
F
Total
3106
1248
972
2089
1271
9,959
3168
1285
997
2140
1297 10,186
3211
1307
1019
2175
1303 10,326
3249
1310
1021
2208
1337 10,471
B
C
D
E
F
G
1554
1891
1768
1152
883
1695
1581
1909
1799
1178
898
1715
A
1273
1299
1312
1346
A
2007
2061
H
1809
1862
Total
12,760
13,003
H
821
845
Total
5788
5898
DUAL PUMP UNITS SI

30XA
UNIT SIZE
090
100
110
120
30XA
UNIT SIZE
140
160

B
C
D
E
F
Total
1409
566
441
947
576
4517
1437
583
452
971
588
4620
1456
593
462
986
591
4684
1474
594
463
1001
607
4750
B
C
D
E
F
G
705
858
802
523
401
769
717
866
816
534
408
778
A
578
589
595
611
A
910
935
30XA090-120
30XA140,160
COOLER SIDE
C
COOLER SIDE
C
B
a30-4420
a30-4421
E
COMPRESSOR SIDE
COMPRESSOR SIDE
29

30XA
UNIT SIZE
080
30XA
UNIT SIZE
090
100
110
120
30XA
UNIT SIZE
140
160
30XA
UNIT SIZE
180
200
30XA
UNIT SIZE
220
240
260
280
300
30XA
UNIT SIZE
325
350
30XA
UNIT SIZE
400
450
500
MOUNTING WEIGHT (lb) Cu/Cu

A
B
C
D
Total
2244
1970
1956
2228
8398
A
B
C
D
E
F
Total
1394
2429
943
1144
2368
1392
9,669
1420
2485
974
1174
2425
1418
9,896
1433
2525
993
1200
2463
1424 10,036
1467
2563
995
1202
2496
1458 10,181
A
B
C
D
E
F
G
H
Total
2188
1735
1058
1375
1411
1078
1876
1990 12,711
2242
1762
1074
1401
1442
1095
1896
2043 12,954
A
B
C
D
E
F
G
H
I
J
Total
1099
1679
1359
2239
1382
1419
2258
1035
1483
1083 15,037
1105
1695
1384
2261
1388
1428
2271
1044
1495
1089 15,159
A
B
C
D
E
F
G
H
I
J
K
995
1378
1865
1771
1010
1398
1441
1030
1636
1337
1419
1012
1400
1891
1794
1013
1401
1443
1033
1645
1347
1443
679
1798
1814
947
2833
1197
1712
2748
984
1517
1754
682
1820
1847
956
2866
1200
1715
2759
988
1542
1775
699
1858
1883
983
2962
1224
1754
2848
1008
1564
1811
A
B
C
D
E
F
G
H
I
J
K
1037
1037
1175
1728
980
2939
1263
1760
2727
1001
1842
1041
1041
1180
1743
990
2993
1274
1786
2780
1006
1848
A
B
C
D
E
F
G
H
I
J
K
1045
1432
1708
3361
1453
987
2609
1269
1764
2681
945
1054
1377
2457
2579
1103
1255
2426
2449
3107
2330
1749
1041
1434
2506
2633
1108
1259
2435
2458
3116
2340
1754
L
1014
1032
679
682
699
Total
16,295
16,455
18,662
18,831
19,292
L
1443
1447
M
1037
1041
N
1037
1041
Total
21,005
21,211
L
1462
1464
1468
M
2547
1738
1756
N
1189
1682
1700
O
1474
1413
1477
L
460
468
308
309
317
Total
7391
7464
8465
8542
8751
L
655
656
M
470
472
N
470
472
Total
9528
9621
L
663
664
666
M
1155
788
797
N
539
763
771
O
669
641
670
P
1065
1073
1061
Total
26,990
29,254
29,547
P
483
487
481
Total
12 243
13 269
13 402

30XA
UNIT SIZE
080
30XA
UNIT SIZE
090
100
110
120
30XA
UNIT SIZE
140
160
30XA
UNIT SIZE
180
200
30XA
UNIT SIZE
220
240
260
280
300
30XA
UNIT SIZE
325
350
30XA
UNIT SIZE
400
450
500
MOUNTING WEIGHT (kg) Cu/Cu

A
B
C
D
Total
1018
893
887
1011
3809
A
B
C
D
E
F
Total
632
1102
428
519
1074
631
4386
644
1127
442
533
1100
643
4489
650
1145
450
544
1117
646
4552
665
1163
451
545
1132
661
4618
A
B
C
D
E
F
G
H
Total
992
787
480
624
640
489
851
903
5766
1017
799
487
636
654
497
860
927
5876
A
B
C
D
E
F
G
H
I
J
Total
499
762
617
1016
627
644
1024
470
673
491
6821
501
769
628
1026
630
648
1030
474
678
494
6876
A
B
C
D
E
F
G
H
I
J
K
451
625
846
804
458
634
653
467
742
607
644
459
635
858
814
460
635
655
469
746
611
654
308
816
823
429
1285
543
777
1246
446
688
796
309
826
838
434
1300
544
778
1252
448
700
805
317
843
854
446
1343
555
796
1292
457
710
821
A
B
C
D
E
F
G
H
I
J
K
470
470
533
784
445
1333
573
798
1237
454
836
472
472
535
791
449
1358
578
810
1261
456
838
A
B
C
D
E
F
G
H
I
J
K
474
649
775
1524
659
447
1183
576
800
1216
428
478
624
1114
1170
500
569
1100
1111
1409
1057
793
472
651
1137
1194
502
571
1105
1115
1413
1061
796
Fig. 11C Unit Mounting Weights (Units with Cu/CU Condenser Coils)
30
30XA220-300
30XA080
COOLER SIDE
B
COOLER SIDE
D
C
a30-4419
a30-4423
J
K
H
I
COMPRESSOR SIDE
COMPRESSOR SIDE
30XA325-350
30XA090-120
COOLER SIDE
C
COOLER SIDE
E
D
C
a30-4424
a30-4420
E
COMPRESSOR SIDE
J
I
K
L
COMPRESSOR SIDE
30XA400-500
30XA140,160
COOLER SIDE
C
B
COOLER SIDE
E
D
C
a30-4421
a30-4425
COMPRESSOR SIDE
L
M
N
COMPRESSOR SIDE
30XA180-200
E
COOLER SIDE
C
a30-4422
COMPRESSOR SIDE
Fig. 11C Unit Mounting Weights (Units with Cu/Cu Condenser Coils) (cont)
31

30XA
UNIT SIZE
090
100
110
120
30XA
UNIT SIZE
140
160

B
C
D
E
F
Total
3139
1280
1093
2330
1392 10,627
3201
1317
1117
2382
1418 10,854
3244
1339
1139
2416
1424 10,994
3282
1342
1142
2449
1458 11,139
B
C
D
E
F
G
1735
1804
1800
1273
1004
1876
1762
1821
1831
1299
1019
1896
A
1394
1420
1433
1467
A
2188
2242
H
1990
2043
Total
13,669
13,912
H
903
927
Total
6200
6310

30XA
UNIT SIZE
090
100
110
120
30XA
UNIT SIZE
140
160

B
C
D
E
F
Total
1424
581
496
1057
631
4820
1452
597
507
1080
643
4923
1471
607
517
1096
646
4987
1489
609
518
1111
661
5053
B
C
D
E
F
G
787
818
816
577
455
851
799
826
830
589
462
860
A
632
644
650
665
A
992
1017
30XA090-120
30XA140,160
COOLER SIDE
C
COOLER SIDE
C
B
a30-4420
a30-4421
E
COMPRESSOR SIDE
COMPRESSOR SIDE
32

30XA
UNIT SIZE
090
100
110
120
30XA
UNIT SIZE
140
160

B
C
D
E
F
Total
3347
1369
1093
2330
1392 10,924
3409
1406
1117
2382
1418 11,151
3452
1428
1139
2416
1424 11,291
3491
1430
1142
2449
1458 11,436
B
C
D
E
F
G
1735
2012
1889
1273
1004
1876
1762
2029
1919
1299
1019
1896
A
1394
1420
1433
1467
A
2188
2242
H
1990
2043
Total
13,966
14,209
H
903
927
Total
6335
6445
DUAL PUMP UNITS SI

30XA
UNIT SIZE
090
100
110
120
30XA
UNIT SIZE
140
160

B
C
D
E
F
Total
1518
621
496
1057
631
4955
1546
638
507
1080
643
5058
1566
648
517
1096
646
5122
1583
649
518
1111
661
5187
B
C
D
E
F
G
787
913
857
577
455
851
799
921
871
589
462
860
A
632
644
650
665
A
992
1017
30XA090-120
30XA140,160
COOLER SIDE
C
COOLER SIDE
C
B
a30-4420
a30-4421
E
COMPRESSOR SIDE
COMPRESSOR SIDE
33
Table 1A Physical Data, 30XA080-500 English

UNIT 30XA
OPERATING WEIGHT (lb)*
Al-Cu Condenser Coils
Cu-Cu Condenser Coils
MCHX Condenser Coils
REFRIGERANT TYPE
Refrigerant Charge (lb) Ckt A/Ckt B/Ckt C
Refrigerant Charge (lb) Ckt A/Ckt B/Ckt C (MCHX)
COMPRESSORS
Quantity
Speed (rpm)
(Qty) Compressor Model Number Ckt A
(Qty) Compressor Model Number Ckt B
(Qty) Compressor Model Number Ckt C
Oil Charge (gal), Ckt A/Ckt B/Ckt C
Minimum Capacity Step (%)
Standard
Optional
COOLER
Net Fluid Volume (gal.)
Maximum Refrigerant Pressure (psig)
Maximum Fluid Side Pressure Without Pumps (psig)
Maximum Fluid Side Pressure With Pumps (psig)
WATER CONNECTIONS
Drain (NPT, in.)
Standard, Inlet and Outlet, Victaulic (in.)
Number of Passes
Minus 1 Pass, Inlet and Outlet, Victaulic (in.)
Number of Passes
Plus 1 Pass, Inlet and Outlet, Victaulic (in.)
Number of Passes
080
090
100
110
120
140
160
180
200
220
7,674
8,398
7,234
9,959
10,924
9,382
10,186
11,151
9,603
10,326
11,291
9,738
10,471
11,436
9,877
12,760
13,966
12,023
13,003
14,209
12,255
13,590
15,037
12,699
13,712
15,159
12,810
14,727
16,295
13,748
86/86/
60/60/
97/97/
62/62/
108/108/
73/73/
135/108/
100/73/
205/205/
141/141/
225/225/
161/161/
270/225/
179/161/
R-134a, EXV Controlled System

135/135/
202/115/
225/135/
100/100/
137/79/
159/100/
Semi-Hermetic Twin Rotary Screws

2
2
2
2
2
2
2
2
3500
(1) 06TS-137 (1) 06TS-137 (1) 06TS-155 (1) 06TS-186 (1) 06TS-186 (1) 06TS-266 (1) 06TT-301 (1) 06TT-266
(1) 06TS-137 (1) 06TS-137 (1) 06TS-155 (1) 06TS-155 (1) 06TS-186 (1) 06TS-155 (1) 06TS-186 (1) 06TT-266
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
5.5/5.5/
5.5/5.5/
5.5/5.5/
5.5/5.5/
5.5/5.5/
6.25/5.5/
6.25/5.5/ 6.25/6.25/
15
9
15
9
15
9
14
8
16.5
220
300
18.5
220
300
150
18.5
220
300
150
20.0
220
300
150
3/
15
10
11
7
Flooded, Shell and Tube Type

23.0
25.5
220
220
300
300
150
150
(1) 06TT-301
(1) 06TT-301
N/A
6.25/6.25/
(1) 06TT-356
(1) 06TT-301
N/A
6.75/6.25/
11
8
15
10
15
10
14
10
27.5
220
300
150
31.5
220
300
34.0
220
300
37.0
220
300
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
5
2
5
1
4
3
5
2
5
1
4
3
5
2
5
1
4
3
5
2
5
1
4
3
5
2
5
1
4
3
5
2
5
1
5
3
5
2
5
1
5
3
6
2
8
1
6
3
6
2
8
1
6
3
6
2
8
1
6
3
CONDENSER FANS
Fan Speed (rpm) Standard/High Ambient**
No. Blades...Diameter (in.)
No. Fans (Ckt A/Ckt B/Ckt C)
Total Airflow (cfm) 850 rpm
850/
9...30
3/3/
55,800
850/
9...30
4/4/
74,400
850/
9...30
4/4/
74,400
Shrouded Axial Type, Vertical Discharge

850/
850/
850/1140
850/1140
9...30
9...30
9...30
9...30
4/4/
4/4/
6/4/
6/4/
74,400
74,400
93,000
93,000
124,000
124,000
850/1140
9...30
6/6/
111,600
148,800
850/1140
9...30
6/6/
111,600
148,800
850/1140
9...30
7/6/
120,900
161,200
CONDENSER COILS
No. Coils (Ckt A/Ckt B/Ckt C)
Total Face Area (sq ft)
3/3/
141
4/4/
188
4/4/
188
4/4/
188
6/6/
281
6/6/
281
7/6/
305
HYDRONIC MODULE (Optional)

Pump
N/A
CHASSIS DIMENSIONS (ft-in.)

Length
Width
Height
UNIT 30XA
OPERATING WEIGHT (lb)
REFRIGERANT TYPE
Refrigerant Charge (lb) Ckt A/Ckt B/Ckt C
Refrigerant Charge (lb) Ckt A/Ckt B/Ckt C (MCHX)
COMPRESSORS
Quantity
Speed (rpm)
Oil Charge (gal), Ckt A/Ckt B/Ckt C
Standard
Optional
COOLER
Net Fluid Volume (gal.)
Maximum Refrigerant Pressure (psig)
Maximum Fluid Side Pressure Without Pumps (psig)
Maximum Fluid Side Pressure With Pumps (psig)
WATER CONNECTIONS
Drain (NPT, in.)
Number of Passes
Number of Passes
Number of Passes
CONDENSER FANS
Fan Speed (rpm) Standard/High Ambient
No. Blades...Diameter (in.)
CONDENSER COILS
Total Face Area (sq ft)
11-10
15-9
6/4/
234
N/A
19-8
23-7
27-6
7-425/32
7-67/16
240
260
280
300
325
350
400
450
500
14,887
16,455
13,897
16,853
18,662
15,720
17,022
18,831
15,878
17,362
19,292
16,141
18,834
21,005
17,467
19,040
21,211
17,659
24,578
26,990
23,038
26,600
29,254
24,901
26,894
29,547
25,167
270/270/
193/193/
375/220/
247/156/
375/270/
260/193/

415/270/
375/375/
415/375/
300/193/
260/260/
300/260/
270/270/375
192/192/258
415/205/415
290/135/290
415/270/415
294/193/294

2
2
2
3500
(1) 06TU-554 (1) 06TU-483 (1) 06TU-554
(1) 06TT-356
(1) 06TU-483 (1) 06TU-483
N/A
N/A
N/A
7.5/6.75/
7.5/7.5/
7.5/7.5/
(1) 06TT-356
(1) 06TT-356
(1) 06TU-483
6.75/6.75/7.5
(1) 06TU-554
(1) 06TT-266
(1) 06TU-554
7.5/6.25/7.5
(1) 06TU-554
(1) 06TT-356
(1) 06TU-554
7.5/6.75/7.5
9
6
6
4
7
5
68.0
220
150
75.0
220
150
83.0
220
150
(1) 06TT-356
(1) 06TT-356
N/A
6.75/6.75/
(1) 06TU-483
(1) 06TT-301
N/A
7.5/6.75/
(1) 06TU-483
(1) 06TT-356
N/A
7.5/6.75/
15
10
11
8
13
9
39.0
220
300
42.0
220
300
44.0
220
300
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
6
2
8
1
6
3
8
2
8
1
8
3
8
2
8
1
8
3
8
2
8
1
8
3
8
2
8
1
8
3
8
2
8
1
8
3
8
1
8
1
8
1
850/1140
9...30
7/6/
120,900
161,200
850/1140
9...30
9/6/
139,500
186,000
850/1140
9...30
10/6/
148,800
198,400
850/1140
9...30
6/6/8
186,000
248,000
850/1140
9...30
8/6/8
204,600
272,800
850/1140
9...30
8/6/8
204,600
272,800
7/6/
305
9/6/
352
10/6/
375
6/6/8
469
8/6/8
516
8/6/8
516
12
7
15
10
15
10

48.5
50.5
53.4
220
220
220
300
300
300

850/1140
850/1140
850/1140
9...30
9...30
9...30
10/6/
9/9/
9/9/
148,800
167,400
167,400
198,400
223,200
223,200
10/6/
375
9/9/
422
9/9/
422
N/A
27-6
31-5
35-4
39-3
43-2
7-43/4
7-67/16
LEGEND
Cu
Al
EXV
MCHX
N/A
6/4/
234
Pump(s) with pressure/temperature taps and combination valve.

Single or Dual, 3600 rpm

Pump
CHASSIS DIMENSIONS (ft-in.)
Length
Width
Height
4/4/
188
* Operating weight includes 2 pumps on models 30XA090-160. No pumps are available on

30XA080 or 30XA180-500. See Fig. 11 for operating weights for units without pumps and units
with single pump packages.
30XA080 unit does not have an economizer.
** The high ambient temperature option is not available on 30XA080-120 units.
Copper
Aluminum
Electronic Expansion Valve
Micro-channel Heat Exchanger
Not Applicable
34
Table 1B Physical Data, 30XA080-500 SI

UNIT 30XA
OPERATING WEIGHT (kg)*
REFRIGERANT TYPE
Refrigerant Charge (kg) Ckt A/Ckt B/Ckt C
Refrigerant Charge (kg) Ckt A/Ckt B/Ckt C (MCHX)
COMPRESSORS
Quantity
Speed (r/s)
Oil Charge (liters), Ckt A/Ckt B/Ckt C
Standard
Optional
COOLER
Net Fluid Volume (liters)
Maximum Refrigerant Pressure (kPa)
Maximum Fluid Side Pressure Without
Pumps (kPa)
Maximum Fluid Side Pressure With Pumps
080
090
100
110
120
140
160
180
200
220
3 481
3 809
3 281
4 517
4 955
4 255
4 620
5 058
4 356
4 684
5 122
4 417
4 750
5 187
4 480
5 788
6 335
5 454
5 898
6 445
5 559
6 164
6 821
5 760
6 220
6 876
5 811
6 680
7 391
6 236
39/39/
27.2/27.2/
44/44/
28.1/28.1/
49/49/
33.1/33.1/
102/61.2/
72.1/45.4/
93/93/
64.0/64.0/
(1) 06TS-137
(1) 06TS-137
N/A
20.8/20.8/
(1) 06TS-137
(1) 06TS-137
N/A
20.8/20.8/
15
9
15
9

49/44/
102/102/
91.6/52.2/
45.4/33.1/ 45.4/45.4/ 62.1/35.8/
102/102 122.5/102/
73.0/73.0/ 81.2/73.0/

2
2
2
2
2
2
2
2
58.3
(1) 06TS-155 (1) 06TS-186 (1) 06TS-186 (1) 06TS-266 (1) 06TT-301 (1) 06TT-266 (1) 06TT-301 (1) 06TT-356
(1) 06TS-155 (1) 06TS-155 (1) 06TS-186 (1) 06TS-155 (1) 06TS-186 (1) 06TT-266 (1) 06TT-301 (1) 06TT-301
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
20.8/20.8/ 20.8/20.8/ 20.8/20.8/ 23.7/20.8/ 23.7/23.7/ 23.7/23.7/ 23.7/23.7/ 25.6/23.7/
15
9
14
8
15
10
11
7

87.1
96.5
1516.8
1516.8
11
8
15
10
15
10
14
10
104.1
1516.8
119.2
1516.8
128.7
1516.8
140.1
1516.8
2 068
62.5
1516.8
70.0
1516.8
70.0
1516.8
75.7
1516.8
2 068
2 068
2 068
2 068
2 068
2 068
2 068
2 068
2 068
1 034
1 034
1 034
1 034
1 034
1 034
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
3/8
5
2
5
1
4
3
5
2
5
1
4
3
5
2
5
1
4
3
5
2
5
1
4
3
5
2
5
1
4
3
5
2
5
1
5
3
5
2
5
1
5
3
6
2
8
1
6
3
6
2
8
1
6
3
6
2
8
1
6
3
CONDENSER FANS
Fan Speed (r/s) Standard/High Ambient**
No. Blades...Diameter (mm)
Total Airflow (L/s) 14.2 r/s
14.2/
9...762
3/3/
26 335
14.2/
9...762
4/4/
35 113
14.2/
9...762
4/4/
35 113

14.2/
14.2/
14.2/19.0
14.2/19.0
9...762
9...762
9...762
9...762
4/4/
4/4/
6/4/
6/4/
35 113
35 113
43 891
43 891
58 522
58 522
14.2/19.0
9...762
6/6/
52 669
70 226
14.2/19.0
9...762
6/6/
52 669
70 226
14.2/19.0
9...762
7/6/
57 059
76 078
CONDENSER COILS
Total Face Area (sq m)
3/3/
13
4/4/
17
4/4/
17
4/4/
17
6/6/
26
6/6/
26
7/6/
28

Pump
N/A
WATER CONNECTIONS
Drain (NPT, in.)
Number of Passes
Number of Passes
Number of Passes
CHASSIS DIMENSIONS (mm)

Length
Width
Height
UNIT 30XA
OPERATING WEIGHT (kg)
REFRIGERANT TYPE
Refrigerant Charge (kg) Ckt A/Ckt B/Ckt C
Refrigerant Charge (kg) Ckt A/Ckt B/Ckt C (MCHX)
COMPRESSORS
Quantity
Speed (r/s)
Oil Charge (liter), Ckt A/Ckt B/Ckt C
Standard
Optional
COOLER
Net Fluid Volume (liters)
Maximum Refrigerant Pressure (kPa)
Maximum Fluid Side Pressure Without
Pumps (kPa)
Maximum Fluid Side Pressure With Pumps
WATER CONNECTIONS
Drain (NPT, in.)
Number of Passes
Number of Passes
Number of Passes
CONDENSER FANS
Fan Speed (r/s) Standard/High Ambient
No. Blades...Diameter (mm)
CONDENSER COILS
Total Face Area (sq m)
3 606
6/4/
22
4 800
N/A
5 994
7 188
8 382
2255
2296.9
240
260
280
300
325
350
400
450
500
6 753
7 464
6 304
7 644
8 465
7 130
7 721
8 542
7 202
7 876
8 751
7 322
8 543
9 528
7 923
8 636
9 621
8 010
11 149
12 243
10 450
12 066
13 269
11 295
12 199
13 402
11 416

122.5/122.5/ 170.1/99.8/ 170.1/122.5/ 188.3/122.5/ 170.1/170.1/ 188.3/170.1/ 122.5/122.5/170.1 188.3/102/188.3 188.3/188.3/122.5
87.5/87.5/ 112.0/71.0/ 118.0/88.0/ 136.1/88.0/ 118.0/118.0/ 136.1/118.0/ 87.1/87.1/117.0 131.5/61.2/131.5 133.3/87.5/133.3
2
(1) 06TT-356
(1) 06TT-356
N/A
25.6/25.6/
(1) 06TU-483
(1) 06TT-301
N/A
28.4/25.6/
(1) 06TU-483
(1) 06TT-356
N/A
28.4/25.6/
15
10
10
8
13
9

2
2
3500
(1) 06TU-554 (1) 06TU-483 (1) 06TU-554
(1) 06TT-356 (1) 06TU-483 (1) 06TU-483
N/A
N/A
N/A
28.4/25.6/
28.4/28.4/
28.4/28.4/
2
12
7
15
10
14
10
(1) 06TT-356
(1) 06TT-356
(1) 06TU-483
25.6/25.6/28.4
(1) 06TU-554
(1) 06TT-266
(1) 06TU-554
28.4/23.7/28.4
(1) 06TU-554
(1) 06TT-356
(1) 06TU-554
28.4/25.6/28.4
9
6
6
4
7
5
147.6
1516.8
159.0
1516.8
166.6
1516.8

183.6
191.2
202.1
1516.8
1516.8
1516.8
257.4
1516.8
283.9
1516.8
314.2
1516.8
2 068
2 068
2 068
2 068
2 068
2 068
1 034
1 034
1 034
3/
3/
3/
3/
3/
3/
3/
3/
3/
6
2
8
1
6
3
8
2
8
1
8
3
8
2
8
1
8
3
14.2/19.0
9...762
7/6/
57 059
76 078
14.2/19.0
9...762
9/6/
65 837
87 782
14.2/19.0
9...762
10/6/
70 226
93 634
7/6/
28
9/6/
33
10/6/
35
8
2
8
1
8
3
8
2
8
1
8
3
8
2
8
1
8
3

14.2/19.0
14.2/19.0
14.2/19.0
9...762
9...762
9...762
10/6/
9/9/
9/9/
70 226
79 004
79 004
93 634
93 634
105 339
10/6/
35
9/9/
39
9/9/
39
8
1
8
1
8
1
14.2/19.0
9...762
6/6/8
87 782
117 043
14.2/19.0
9...762
8/6/8
96 561
128 747
14.2/19.0
9...762
8/6/8
96 561
128 747
6/6/8
44
8/6/8
48
8/6/8
48
N/A
8 382
9 576
10 770
2 255
2 300
LEGEND
Cu
Al
EXV
MCHX
N/A
6/4/
22
Pump(s) with pressure/temperature taps and combination valve. Single or Dual, 58.3 r/s

Pump
CHASSIS DIMENSIONS (mm)
Length
Width
Height
4/4/
17
11 964
13 158
* Operating weight includes 2 pumps on models 30XA090-160. No pumps are available on

30XA080 or 30XA180-500. See Fig. 11 for operating weights for units without pumps and units
with single pump packages.
30XA080 unit does not have an economizer.
** The high ambient temperature option is not available on 30XA080-120 units.
Copper
Aluminum
Electronic Expansion Valve
Micro-channel Heat Exchanger
Not Applicable
35
See Fig. 12-14 for rigging centers of gravity.

For shipping, some domestic units and all export units are
mounted on a wooden skid under entire base of unit. Skid can
be removed before unit is moved to installation site. Lift the
unit from above to remove skid. See Fig. 12-14 for rigging
center of gravity. On export units, the top skid can be used as
the spreader bars. If the unit was shipped with a shipping bag,
the bag must be removed to gain access to the rigging holes in
the base rail.
If overhead rigging is not available, the unit can be moved
on rollers or dragged. When unit is moved on rollers, the unit
skid, if equipped, must be removed. To lift the unit, use jacks at
the rigging points. Use a minimum number of rollers to distribute the load such that the rollers are no more than 6 ft (1.8 m)
apart. If the unit is to be dragged, lift the unit as described
above, and place unit on a pad. Apply moving force to the pad,
and not the unit. When in its final location, raise the unit and
remove the pad. If the unit was shipped with coil protection, it
must be removed before start-up. The shipping bag for export
units must be removed before start-up.
RIGGING UNIT (See Fig. 12-14) The 30XA080-500 units

are designed for overhead rigging and it is important that this
method be used. Holes are provided in frame base channels,
marked for rigging (see rigging label on unit). Field-supplied
shackles are required to facilitate lifting. Secure the shackles
to the base rails at the points noted on the rigging label. See
Table 2 for the number of lifting points for each unit.
Do not use a forklift truck to move the units.
Table 2 Number of Lifting Points for 30XA080-500
30XA UNIT SIZE
080
090-120
140, 160
180, 200
220-400
450, 500
NUMBER OF LIFTING POINTS

4
6
8
10
12
14
Use spreader bars to keep cables or chains clear of unit sides.

As further protection plywood sheets may be placed against
sides of unit, behind cables or chains. Run cables or chains to a
central suspension point so that angle from horizontal is not less
than 45 degrees. Raise and set unit down carefully.
CAUTION - NOTICE TO RIGGERS:

ALL PANELS MUST BE IN PLACE WHEN RIGGING. DO NOT ATTEMPT TO FORK THESE UNITS IF NO SKID IS SUPPLIED.
NOTES:
1. 1.50 dia. (38.1mm) lifting holes provided for field supplied clevis.
2. Rig with a minimum of 25 ft (7620mm) length chains or cables.
3. If central lifting point is used, it must be a minimum of 13 ft. (3962mm) above the top of the unit.
4. Spreader bars made from steel or double nailed, and notched 2x6's approximately 8 ft. (2438mm) long, must
be placed just above the top of the unit (and stacks) to reduce the risk of damage to the top of the unit and
coils.
5. If overhead rigging is not available, the unit can be moved on rollers or dragged. When unit is moved on
rollers, the unit skid, if equipped, must be removed. To lift the unit, use jacks at the rigging points. Use a
minimum of one roller every 6 ft. (1829mm) to distribute the load. If the unit is to be dragged, lift the unit as
described above, and place unit on a pad. Apply moving force to the pad, not the unit. When in its final
location, raise the unit and remove the pad.
9829
4466
8849
4021
4795
10553
9573
4350
10936
4969
9866
4483
5408
11901
10831
4922
11162
5072
10092
4586
5511
12127
11057
5024
5132
11293
10223
4645
5570
12258
11188
5084
5193
11427
10357
4706
5631
12392
11322
5145
6266
13788
12628
5739
6814
14994
13834
6287
6371
14018
5843
12858
6919
15225
6392
14065
7237
15925
6669
14675
7895
17372
7327
16122
7285
16030
6717
14780
7943
17477
7375
16227
SUBSTRACT THESE VALUES FOR UNITS W/O PUMPS
30XA080
30XA080-CU
30XA090
30XA090-CU
30XA100
30XA100-CU
30XA110
30XA110-CU
30XA120
30XA120-CU
30XA140
30XA140-CU
30XA160
30XA160-CU
30XA180
30XA180-CU
30XA200
30XA200-CU
30XA090-160
SINGLE PUMP
LBS
KGS
958
435
a30-4427
DUAL PUMP
LBS
KGS
1255
569
Fig. 12 Unit Rigging Label Detail 30XA080-200

36

NOTES:
coils.
6. Check bill of lading for shipping weight of unit.
a30-4428

The combination valve performs the following functions:
Drip-tight shut-off valve
Spring closure design with a non-slam check valve
Flow-throttling valve
When facing the cooler side of unit, the inlet (return) water
connection is on the bottom. The outlet (supply) water connection is on the top. The inlet is connected to the suction guide/
strainer of the pump via a Victaulic-type connection. The cooler supply has water-side Victaulic-type connections (follow
connection directions as provided by the coupling manufacturer). Provide proper support for the piping. If accessory security
grilles have been added, holes must be cut in the grilles for
field piping and insulation.
There is a factory supplied, insulated 45-degree elbow pipe
and a victaulic coupling shipped with units ordered with a
hydronic pump package. Before starting field piping, use the
victaulic coupling to connect this elbow pipe to the outlet of the
combination valve.
Step 3 Cooler Fluid and Drain Piping Connections See Fig. 15-18 for piping applications.
Remove the chilled water flow switch, entering and leaving

water thermistors before welding connecting piping. Reinstall flow switch and thermistors after welding is complete.
Failure to remove these devices may cause unit damage.
GENERAL The factory-installed victaulic connections allow clamp-on connection of water lines to the coolers in all
30XA units. A flow sensor is factory-installed in the side of the
entering fluid nozzle. See Fig. 19. See Table 3 for 30XA unit
operating range. See Fig. 16 for cooler option dimensions.
UNITS WITH HYDRONIC PUMP PACKAGE The
30XA090-160 units can be equipped with a factory-installed
hydronic pump package consisting of a suction guide/strainer,
pump, combination valve, internal piping and wiring connected at the factory.
37

NOTES:
coils.
6. Check bill of lading for shipping weight of unit.
a30-4428

NOTE: It is required that a 20 mesh field-supplied strainer be
installed in the inlet piping to the cooler on open loop systems.
A 3/4 in. NPT fitting is installed in the inlet piping of the
pump for connection to an expansion tank. Install the tank in
accordance with the manufacturer's instructions.
Figures 20 and 21 illustrate typical single and dual pump
packages.
Three drain connections are provided and are located at
leaving water (supply) end of cooler, pump volute, and the
suction guide. See Fig. 2-10 for connection location. Insulate
the drain piping (in the same manner as the chilled water piping) for at least 12 in. (305 mm) from the cooler.
The suction guide/strainer is shipped from the factory with a

run-in screen. This screen is a temporary device used during
the start-up/clean-up process of the chilled water circuit to
prevent construction debris from damaging the pump or
internal tubes of the cooler. After all debris has been removed
or a maximum of 24 running hours the temporary screen must
be removed. See the Start-Up, Controls, Operation and
Troubleshooting guide for further information.
The suction guide/strainer is shipped from the factory with

a run-in screen. This temporary screen must be removed
after all debris has been removed or a maximum of 24 running hours. Failure to remove the temporary screen may
result in damage to the pump or cooler.
38
POWER
FD
FD
CONTROL
BALANCING VALVE/
SHUT OFF*
VIBRATION
ELIMINATORS*
STRAINER*
GATE VALVE*
PUMP
LEGEND
FD
Fused Disconnect
Airflow Through Condenser
Chilled Water Piping
Power Wiring
*Field-installed.
DRAIN
PRESSURE/
SHUTOFF TEMPERATURE TAPS*
VALVE
a30-4114
NOTES:
1. Chiller must be installed level to maintain proper compressor oil return.
2. Piping shown are general points-of-connection guides only and are not
intended for a specific installation. Wiring and piping shown are for a quick
overview of system and are not in accordance with recognized standards.
3. All wiring must comply with applicable local and national codes.
4. All piping must follow standard piping techniques. Refer to Carrier System
Design Manual or appropriate ASHRAE (American Society of Heating,
Refrigeration, and Air Conditioning Engineers) handbook for details.
Fig. 15A 30XA Typical Piping and Wiring (Units without Hydronic Package)
AIRFLOW
FIELD-SUPPLIED
FUSED DISCONNECT
UNIT POWER
FIELD-SUPPLIED
FUSED DISCONNECT
CONTROL POWER
NOTES:
1. Chiller must be installed level to maintain proper
compressor oil return and hydraulics.
2. Wiring and piping shown are general points-ofconnection guides only and are not intended for a
specific installation. Wiring and piping shown are
for a quick overview of system and are not in
accordance with recognized standards.
3. All wiring must comply with applicable local and
national codes.
4. All piping must follow standard piping techniques.
Refer to Carrier System Design Manual or appropriate ASHRAE (American Society of Heating,
Refrigeration, and Air Conditioning Engineers)
handbook for details.
5. Air separator required as close to chiller as possible (except primary/secondary systems).
6. 20 mesh strainer required for open loop systems.
BALANCING VALVE/
SHUTOFF*
PRESSURE/
TEMPERATURE
TAPS*
VIBRATION
ELIMINATORS*
DRAIN SHUTOFF VALVE
LEGEND
STRAINER*
Airflow Through Condenser

GATE VALVE*
Power Wiring
Chilled Water Piping
PUMP
*Field-installed.
Fig. 15B 30XA Typical Piping and Wiring (Units with Hydronic Package)
39
40
Distance to
Leaving
Water
Connection
(mm)
3077.8
3069.6
3069.6
3069.6
3069.6
3085.8
3085.8
4512.3
4502.4
5706.2
5706.2
7739.6
7739.6
7739.6
8865.1
8865.1
30XA
UNIT
SIZE*
080
090
100
110
120
140
160
180
200
220
240
260
280
300
325
350
SI
Leaving
W ater
Distance to Leaving
Water Connection
Distance to
Leaving/Entering
Water Connection
Fig. 16 Cooler Option Dimensions
Distance to Entering
Water Connection
Cooler
Top View
Height Leaving
Water Connection
Height Entering
Water Connection
Coil
Side View
STANDARD COOLER
PLUS ONE PASS COOLER
MINUS ONE PASS COOLER
Distance to Distance to
Height
Height
Distance
to
Height
Height
Distance
to
Height
Height
Leaving/
Victaulic
Leaving/
Victaulic
Leaving/
Victaulic
Leaving
Entering
Entering
Leaving
Leaving
Entering
Entering
Leaving
Leaving
Entering
Entering
Entering
Connection
Entering
Connection
Entering
Connection
Water
Water
Water
Water
Water
Water
Water
Water
Water
Water
Water
Water
Size
Water
Size
Water
Size
Connection Connection Connection Connection
Connection Connection Connection Connection Connection
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
(mm)
484.0
1728.7
3077.8
274.2
127.0
37.9
497.2
1728.7
3077.8
261.0
101.6
55.1
379.1
1728.7
3170.7
379.1
127.0
484.0
1728.7
3069.6
274.2
127.0
29.7
497.2
1728.7
3069.6
261.0
101.6
63.2
379.1
1728.7
3162.6
379.1
127.0
484.0
1728.7
3069.6
274.2
127.0
29.7
497.2
1728.7
3069.6
261.0
101.6
63.2
379.1
1728.7
3162.6
379.1
127.0
484.0
1728.7
3069.6
274.2
127.0
29.7
497.2
1728.7
3069.6
261.0
101.6
63.2
379.1
1728.7
3162.6
379.1
127.0
484.0
1728.7
3069.6
274.2
127.0
29.7
497.2
1728.7
3069.6
261.0
101.6
63.2
379.1
1728.7
3162.6
379.1
127.0
540.5
1756.2
3085.8
268.7
127.0
30.1
540.5
1756.2
3085.8
268.7
127.0
55.0
404.6
1756.2
3170.8
404.6
152.4
540.5
1756.2
3085.8
268.7
127.0
30.1
540.5
1756.2
3085.8
268.7
127.0
55.0
404.6
1756.2
3170.8
404.6
152.4
571.0
1782.1
4512.3
287.0
152.4
1361.4
569.5
1782.1
4587.2
288.5
152.4
1361.4
336.0
1782.1
4587.2
336.0
203.2
571.0
1782.1
4502.4
287.0
152.4
1351.6
569.5
1782.1
4577.4
288.5
152.4
1351.6
336.0
1782.1
4577.4
336.0
203.2
571.0
1782.1
5706.2
287.0
152.4
2555.3
569.5
1782.1
5781.1
288.5
152.4
2555.3
336.0
1782.1
5781.1
336.0
203.2
571.0
1782.1
5706.2
287.0
152.4
2555.3
569.5
1782.1
5781.1
288.5
152.4
2555.3
336.0
1782.1
5781.1
336.0
203.2
600.2
1804.9
7739.6
310.1
203.2
4580.8
593.9
1804.9
7882.8
316.5
203.2
4580.8
413.3
1804.9
7882.8
413.3
203.2
600.2
1804.9
7739.6
310.1
203.2
4580.8
593.9
1804.9
7882.8
316.5
203.2
4580.8
413.3
1804.9
7882.8
413.3
203.2
600.2
1804.9
7739.6
310.1
203.2
4580.8
593.9
1804.9
7882.8
316.5
203.2
4580.8
413.3
1804.9
7882.8
413.3
203.2
600.2
1804.9
8865.1
310.1
203.2
5706.4
593.9
1804.9
9008.4
316.5
203.2
5706.4
413.3
1804.9
9008.4
413.3
203.2
600.2
1804.9
8865.1
310.1
203.2
5706.4
593.9
1804.9
9008.4
316.5
203.2
5706.4
413.3
1804.9
9008.4
413.3
203.2
*30XA400-500 units are equipped with standard coolers only. Refer to unit dimensional drawings for cooler dimensions.
NOTE: Refer to dimensional drawings for all other unit dimensions.
121.2
120.9
120.9
120.9
120.9
121.5
121.5
177.7
177.3
224.7
224.7
304.7
304.7
304.7
349.0
349.0
080
090
100
110
120
140
160
180
200
220
240
260
280
300
325
350
30XA Distance to
Leaving
UNIT
Water
SIZE*
Connection
(in.)
ENGLISH
STANDARD COOLER
PLUS ONE PASS COOLER
MINUS ONE PASS COOLER
Distance to
Distance
Height
Height
Distance to
Height
Height
Distance to
Height
Height
Leaving/
Victaulic
Leaving/
to
Victaulic
Leaving/
Victaulic
Leaving
Entering
Entering
Leaving
Leaving
Entering
Leaving
Leaving
Entering
Entering
Entering
Connection
Entering
Entering
Connection
Entering
Connection
Water
Water
Water
Water
Water
Water
Water
Water
Water
Water
Water
Size
Water
Water
Size
Water
Size
Connection Connection Connection Connection
(in.)
(in.)
(in.)
(in.)
(in.)
(in.)
(in.)
(in.)
(in.)
(in.)
(in.)
(in.)
(in.)
(in.)
(in.)
(in.)
(in.)
19.1
68.1
121.2
10.8
5.0
1.5
19.6
68.1
121.2
10.3
4.0
2.2
14.9
68.1
124.8
14.9
5.0
19.1
68.1
120.9
10.8
5.0
1.2
19.6
68.1
120.9
10.3
4.0
2.5
14.9
68.1
124.5
14.9
5.0
19.1
68.1
120.9
10.8
5.0
1.2
19.6
68.1
120.9
10.3
4.0
2.5
14.9
68.1
124.5
14.9
5.0
19.1
68.1
120.9
10.8
5.0
1.2
19.6
68.1
120.9
10.3
4.0
2.5
14.9
68.1
124.5
14.9
5.0
19.1
68.1
120.9
10.8
5.0
1.2
19.6
68.1
120.9
10.3
4.0
2.5
14.9
68.1
124.5
14.9
5.0
21.3
69.1
121.5
10.6
5.0
1.2
21.3
69.1
121.5
10.6
5.0
2.2
15.9
69.1
124.8
15.9
6.0
21.3
69.1
121.5
10.6
5.0
1.2
21.3
69.1
121.5
10.6
5.0
2.2
15.9
69.1
124.8
15.9
6.0
22.5
70.2
177.7
11.3
6.0
53.6
22.4
70.2
180.6
11.4
6.0
53.6
13.2
70.2
180.6
13.2
8.0
22.5
70.2
177.3
11.3
6.0
53.2
22.4
70.2
180.2
11.4
6.0
53.2
13.2
70.2
180.2
13.2
8.0
22.5
70.2
224.7
11.3
6.0
100.6
22.4
70.2
227.6
11.4
6.0
100.6
13.2
70.2
227.6
13.2
8.0
22.5
70.2
224.7
11.3
6.0
100.6
22.4
70.2
227.6
11.4
6.0
100.6
13.2
70.2
227.6
13.2
8.0
23.6
71.1
304.7
12.2
8.0
180.3
23.4
71.1
310.3
12.5
8.0
180.3
16.3
71.1
310.3
16.3
8.0
23.6
71.1
304.7
12.2
8.0
180.3
23.4
71.1
310.3
12.5
8.0
180.3
16.3
71.1
310.3
16.3
8.0
23.6
71.1
304.7
12.2
8.0
180.3
23.4
71.1
310.3
12.5
8.0
180.3
16.3
71.1
310.3
16.3
8.0
23.6
71.1
349.0
12.2
8.0
224.7
23.4
71.1
354.7
12.5
8.0
224.7
16.3
71.1
354.7
16.3
8.0
23.6
71.1
349.0
12.2
8.0
224.7
23.4
71.1
354.7
12.5
8.0
224.7
16.3
71.1
354.7
16.3
8.0
a30-4413
CONTROL
BOX
MASTER CHILLER
PUMP & CHECK VALVE
OR ISOLATION VALVE
CONTROL
BOX
SLAVE CHILLER
PUMP & CHECK VALVE
LWT
OR ISOLATION VALVE
DUAL CHILLER
LWT SENSORS
& WELLS
LEGEND
Leaving Water Temperature
Field-Installed Communication Bus (slashes
indicate number of conductor wires)
Field-Installed Wiring
Twisted Pair
a30-4417
Fig. 17 Parallel Dual Chiller Operation
CONTROL
BOX
SLAVE CHILLER
PUMP
CONTROL
BOX
MASTER CHILLER
LEGEND
Field-Installed Communication Bus (slashes
indicate number of conductor wires)
Field-Installed Wiring
a30-4418
Fig. 18 Series Dual Chiller Operation
41
a30-4138
FLOW SWITCH
Fig. 19 Flow Switch
T1 PP
Heater
FS PP T2
PT
INSIDE
UNIT
HYDRONIC PUMP PACKAGE
PT
D
PT
OUTSIDE
UNIT
Chilled
Water Out
PT
PT
Heater
Air Separator with Vent*
D
D
E
FS
PP
PT
T1
T2
V
LEGEND
Drain,3/4-in. NPT
Drain, 1/4-in. NPT
Expansion Tank Connection, 3/4-in. NPT
Flow Switch
Pipe Plug, 1/4-in. NPT
Pressure/Temperature Tap
Leaving Water Thermistor
Entering Water Thermistor
Vent, 1/4-in. NPT
Indicates items provided with the
optional hydronic pump package.
*Field-supplied and installed.

Factory-installed option.
**Required for open loop systems.
Chilled
Water In
Strainer/Suction Guide
Pump
Combination Valve
Pressure Relief*
Isolation Valve*
Flexible Connections*
a30-4414
Pressure Reducing
Fill Valve*
20 Mesh Stainer**
Fig. 20 Typical Piping Diagram on 30XA Units with Hydronic Package Single Pump
42
T1 PP
Heater
FS PP T2
PT HYDRONIC PUMP PACKAGE
D
PT
D
PT
INSIDE
UNIT
OUTSIDE
UNIT
Chilled
Water Out
PT
PT
D
Heater
D
D
E
FS
PP
PT
T1
T2
V
LEGEND
Drain,3/4-in. NPT
Drain, 1/4-in. NPT
Expansion Tank Connection, 3/4-in. NPT
Flow Switch
Pressure/Temperature Tap
Vent, 1/4-in. NPT
Air Separator with Vent*
Chilled
Water In
Strainer/Suction Guide
Reverse Flow Check

Valve/Service Valve
*Field-supplied and installed.

Factory-installed option.
**Required for open loop systems.
Service Valve
Pump
Combination Valve
Pressure Relief*
a30-4415
Flexible Connections*
Isolation Valve*
Pressure Reducing
Fill Valve*
20 Mesh Stainer**
Fig. 21 Typical Piping Diagram on 30XA Units with Hydronic Package Dual Pumps
volume should be increased to 6 to 10 gallons per ton (6.46 to
10.76 liters per kW) of cooling. In order to achieve this
volume, it may be necessary to add a water storage tank to the
water loop. If a storage tank is added to the system, it should be
properly vented so that the tank can be completely filled and all
air eliminated. Failure to do so could cause lack of pump stability and poor system operation. Any storage tank that is placed
in the water loop should have internal baffles to allow thorough
mixing of the fluid. See Fig. 23.
System Piping Proper system design and installation procedures should be followed closely. The system must be
constructed with pressure tight components and thoroughly
tested for installation leaks. Factory-supplied hydronic systems
are available with single or dual (for back-up) pumps. The
factory-installed system includes all of the components above
the line in Fig. 20 and 21.
Installation of water systems should follow sound engineering practice as well as applicable local and industry standards.
Improperly designed or installed systems may cause unsatisfactory operation and/or system failure. Consult a water
treatment specialist or appropriate literature for information
regarding filtration, water treatment, and control devices. Figures 20 and 21 show a typical installation with components that
might be installed with the hydronic package of the 30XA unit.
NOTE: It is recommended for units with the hydronic package
that an inlet isolation (shut-off) valve be placed exterior to the
unit to allow removal and service of the entire pump assembly,
if necessary. The hydronic package is supplied from the factory
UNITS WITHOUT HYDRONIC PUMP PACKAGE When

facing the cooler side of the unit, the inlet (return) water connection is on the bottom. It is required that a field-supplied strainer
with a minimum size of 20 mesh be installed within 10 ft
(3.05 m) of the cooler inlet to prevent debris from damaging internal tubes of the cooler. The outlet (supply) water connection is
on the top. The cooler has water-side victaulic-type connections
(follow connection directions as provided by the coupling manufacturer). Provide proper support for the piping. If accessory security grilles have been added, holes must be cut in the grilles for
field piping and insulation. See Fig. 22 for a typical piping diagram of a 30XA unit without a hydronic pump package.
A drain connection is located at the leaving water (supply)
end of cooler. See Fig. 2-10 for connection location. Insulate
the drain piping (in the same manner as the chilled water
piping) for at least 12 in. (305 mm) from the unit.
Dual Chiller Leaving Water Sensor If the Dual Chiller algorithm is used, and the machines are installed in parallel, a
dual chilled water sensor must be installed for each module. Install the well in the common leaving water header. See Fig. 17.
The series dual chiller application is shown in Fig. 18.
Minimum Loop Volume The preferred minimum loop volume is dependent on the type of application. In order to obtain
leaving water temperature stability for comfort cooling applications, a minimum of 3 gallons per ton (3.25 liters per kW) is
required on all unit sizes. For process cooling applications, applications where high stability is critical, or operation at
ambient temperatures below 32 F (0 C) is expected, the loop
43
with a combination valve for isolation of leaving water. Also, if

the unit is isolated with valves, a properly sized pressure relief
valve is recommended and should be installed in the piping
between the unit and the valves, following all applicable local
codes.
Air Separation For proper system operation, it is essential
that water loops be installed with proper means to manage air
in the system. Free air in the system can cause noise, reduce
terminal output, stop flow, or even cause pump failure due to
pump cavitation. For closed systems, equipment should be
provided to eliminate all air from the system.
The amount of air that water can hold in solution depends
on the pressure and temperature of the water/air mixture. Air is
less soluble at higher temperatures and at lower pressures.
Therefore, separation can best be done at the point of highest
water temperature and lowest pressure. Typically, this point
would be on the suction side of the pump as the water is returning from the system or terminals. This is generally the optimal
place to install an air separator, if possible.
1. Install automatic air vents at all high points in the system.
(If the 30XA unit is located at the high point of the system, a vent can be installed on the piping leaving the heat
exchanger on the 1/4 in. NPT female port.)
2. Install an air separator in the water loop, at the place
where the water is at higher temperatures and lower pressures usually in the chilled water return piping. On a
primary-secondary system, the highest temperature water
is normally in the secondary loop, close to the decoupler.
Preference should be given to that point on the system
(see Fig. 24). In-line or centrifugal air separators are
readily available in the field.
It may not be possible to install air separators at the place of
the highest temperature and lowest pressure. In such cases,
preference should be given to the points of highest temperature.
It is important that the pipe be sized correctly so that free air
can be moved to the point of separation. Generally, a water
velocity of at least 2 feet per second (0.6 m per second) will
keep free air entrained and prevent it from forming air pockets.
Automatic vents should be installed at all physically elevated points in the system so that air can be eliminated during system operation. Provisions should also be made for manual
venting during the water loop fill.
GOOD
BAD
BAD
a30-3185
GOOD
Fig. 23 Tank Baffling

ComfortLink feature requires a communication link between the
2 chillers.
There are several advantages to this type of control:
redundancy (multiple circuits)
better low load control, (lower tonnage capability)
lower rigging lift weights (2 machines rather than 1 large
machine)
chiller lead-lag operation (evens the wear between the
two machines)
Parallel Dual Chiller Operation Parallel chiller operation
is the recommended option for dual chiller control. In this case,
each chiller must control its own dedicated pump or isolation
valve. Balancing valves are recommended to insure proper
flow in each chiller. Two field-supplied and installed dual chiller leaving water temperature sensors are required, one for each
module for this function to operate properly.
Consider adding additional isolation valves to isolate each
chiller to allow for service on a machine, and still allow for partial capacity from the other chiller. See Fig 17.
Series Dual Chiller Operation Series chiller operation is an
alternate control method supported by the ComfortLink
control system. Certain applications might require that the two
chillers be connected in series. For nominal 10 F (5.6 C) cooler ranges, use the Minus 1 Pass cooler arrangements to reduce
the fluid-side pressure drop. Use the standard cooler pass
arrangement for low flow, high cooler temperature rise
applications.
Consider adding additional piping and isolation valves to
isolate each chiller to allow for service on a machine, and still
allow for partial capacity from the other chiller. See Fig. 18.
IMPORTANT: Automatic vents should be located in

accessible locations for maintenance purposes and
protected from freezing.
DUAL CHILLER CONTROL the ComfortLink controller allows 2 chillers (piped in parallel or series) to operate as a
single chilled water plant with standard control functions
coordinated through the master chiller controller. This standard
T1 PP
Chilled Water Out
Heater
D
FS
PP
T1
T2
V
Chilled Water In
LEGEND
Drain, 3/4-in. NPT
Flow Switch
Vent, 1/4-in. NPT
a30-4416
FS PP T2
Fig. 22 Typical Piping Diagram on 30XA Units without Hydronic Package

44
Table 3 30XA Minimum and Maximum Cooler Flow Rates

ITEM
Cooler Leaving Water Temperature*
Cooler Entering Water Temperature
30XA
UNIT SIZE
080
090
100
110
120
140
160
180
200
220
240
260
280
300
325
350
400
450
500
Cooler
Number of
Passes
Standard
Plus one pass
Minus one pass
Standard
Plus one pass
Minus one pass
Standard
Plus one pass
Minus one pass
Standard
Plus one pass
Minus one pass
Standard
Plus one pass
Minus one pass
Standard
Plus one pass
Minus one pass
Standard
Plus one pass
Minus one pass
Standard
Plus one pass
Minus one pass
Standard
Plus one pass
Minus one pass
Standard
Plus one pass
Minus one pass
Standard
Plus one pass
Minus one pass
Standard
Plus one pass
Minus one pass
Standard
Plus one pass
Minus one pass
Standard
Plus one pass
Minus one pass
Standard
Plus one pass
Minus one pass
Standard
Plus one pass
Minus one pass
Standard
Plus one pass
Minus one pass
Standard
Plus one pass
Minus one pass
Standard
Plus one pass
Minus one pass
2
3
1
2
3
1
2
3
1
2
3
1
2
3
1
2
3
1
2
3
1
2
3
1
2
3
1
2
3
1
2
3
1
2
3
1
2
3
1
2
3
1
2
3
1
2
3
1
1
MINIMUM
40 F (4.4 C)
45 F (7.2 C)
Minimum Flow Rate
(gpm)
(L/s)
95
6.0
43
2.7
196
12.4
101
6.4
43
2.7
229
14.4
101
6.4
43
2.7
229
14.4
125
7.9
61
3.8
254
16.0
125
7.9
73
4.6
281
17.7
134
8.5
73
4.6
324
20.4
165
10.4
98
6.2
354
22.3
202
12.7
73
4.6
416
26.2
223
14.1
98
6.2
458
28.9
235
14.8
122
7.7
501
31.6
266
16.8
147
9.3
538
33.9
257
16.2
141
8.9
584
36.8
293
18.5
141
8.9
620
39.1
327
20.6
174
11.0
687
43.3
361
22.8
211
13.3
724
45.7
379
23.9
244
15.4
767
48.4
501
31.6
501
501
* For applications requiring cooler leaving water temperature operation at less than
40 F (4.4 C), the units require the use of antifreeze and application may require
one of the special order brine option. Contact your local Carrier representative for
more information.
For applications requiring cooler entering water temperature operation at less than
45 F (7.2 C), contact your local Carrier representative for unit selection using the
Carrier electronic catalog.
MAXIMUM
60 F (15 C)
70 F (21.1 C)
Maximum Flow Rate
(gpm)
(L/s)
379
23.9
192
12.1
782
49.3
403
25.4
200
12.6
917
57.9
403
25.4
200
12.6
917
57.9
501
31.6
244
15.4
1014
64.0
501
31.6
293
18.5
1124
70.9
538
33.9
293
18.5
1296
81.8
660
41.6
391
24.7
1418
89.5
807
50.9
391
24.7
1662
104.9
892
56.3
391
24.7
1833
115.6
941
59.4
489
30.9
2004
126.4
1063
67.1
587
37.0
2151
135.7
1027
64.8
562
35.5
2334
147.3
1173
74.0
562
35.5
2481
156.5
1308
82.5
697
44.0
2750
173.5
1442
91.0
843
53.2
2897
182.8
1516
95.6
978
61.7
3068
193.6
2004
126.4
2004
2004
NOMINAL
Nominal Flow Rate

(gpm)
(L/s)
180.4
11.4
201.9
12.7
225.5
14.2
244.9
15.5
264.8
16.7
317.8
20.1
365.1
23.0
409.6
25.8
463.9
29.3
505.9
31.9
545.8
34.4
600.3
37.9
642.2
40.5
687.5
43.4
733.4
46.3
775.4
48.9
917.6
57.9
1019.3
64.3
1092.8
68.9
NOTE: Nominal flow rates required at ARI (Air Conditioning and Refrigeration
Institute) conditions 44 F (7 C) leaving fluid temperature, 54 F (12 C) entering
water temperature, 95 F (35 C) ambient. Fouling factor 0.00010 ft2-hr-F/Btu
(0.000018 m2-K/kW).
45
Expansion
Tank(s)
Zone 2
Zone 1
Chiller 2
Chiller 1
Decoupler
Zone 3
a30-4002
Distribution Pump
Air Separator
with Vent
NOTE: Expansion tanks for 30XA hydronic kits must be installed for chillers piped in parallel in the primary water loop.
Fig. 24 Typical Air Separator and Expansion Tank Location on Primary-Secondary Systems
PREPARATION FOR YEAR-ROUND OPERATION In
areas where the piping or unit is exposed to 32 F (0 C) or
lower ambient temperatures, freeze-up protection is required
using inhibited glycol or other suitable corrosion-resistant antifreeze solution and electric heater tapes. Heater tapes on piping
should have a rating for area ambient temperatures and be covered with a suitable thickness of closed-cell insulation. Route
power for the heater tapes from a separately fused disconnect.
Mount the disconnect within sight from the unit per local or
NEC (National Electric Code) codes. Identify disconnect at
heater tape power source with a warning that power must not
be turned off except when servicing unit.
COOLER PUMP CONTROL It is recommended that

cooler pump control be utilized on all chillers unless the
chilled water pump runs continuously or the chilled water system contains a suitable antifreeze solution. Units that are not
supplied with a factory-installed hydronic package require
installation of the External Pump Control accessory package
(Part No. 00EFN900003200A).
If cooler pump control is not utilized it is recommended that
the chiller be electrically interlocked with the chilled water
pump starter to provide additional protection. The interlock
should be wired to terminals TB5-1 and TB5-2. It is also
recommended that the cooler pump output be used as an override to the chilled water pump control circuit to provide additional freeze protection, if required.
Refer the Control and Power Wiring Schematic on page 55
for proper connection of the cooler pump output. The cooler
pump output will remain energized for 30 seconds after all
compressors stop due to an OFF command. In the event a
freeze protection alarm is generated, the cooler pump output
will be energized regardless of the cooler pump control software configuration. The cooler pump output is also energized
anytime a compressor is started and when certain alarms are
generated. A thermal flow sensor is factory installed in the entering fluid nozzle to prevent operation without flow through
the cooler. See Fig. 25. The flow sensor is factory wired.
Proper software configuration of the cooler pump control
parameters is required to prevent possible cooler freeze-up.
Refer to the Controls, Start-Up, Operation, Service and
Troubleshooting guide for more information.
BRINE UNITS Special factory modifications to the units
are required to allow them to operate at fluid temperatures
less than 40 F (4.4 C). Be sure that the fluid has sufficient
inhibited glycol or other suitable corrosion-resistant antifreeze solution to prevent cooler freeze-up.
WATER TREATMENT Untreated or improperly treated
water may result in corrosion, scaling, erosion, or algae. The
services of a qualified water treatment specialist should be
obtained to develop and monitor a treatment program.
IMPORTANT: Adding antifreeze solution is the only

certain means of protecting the unit from freeze-up if
heater fails or electrical power is interrupted or lost
while temperatures are below 32 F (0 C).
IMPORTANT: Before starting the unit, be sure all of
the air has been purged from the system.
A drain connection is located at the bottom of the cooler
head. See Fig. 2-10 for connection location. Install shut-off
valves to the drain line before filling the system with fluid.
Water must be within design flow limits, clean, and treated

to ensure proper chiller performance and reduce the potential of tube damage due to corrosion, scaling, erosion, and
algae. Carrier assumes no responsibility for chiller damage
resulting from untreated or improperly treated water.
a30-3432
NOTE: Do not use automobile anti-freeze, or any other fluid

that is not approved for heat exchanger duty. Only use appropriately inhibited glycols, concentrated to provide adequate
protection for the temperature considered.
Fig. 25 Thermal Flow Sensor
46
Low Ambient Temperature Head Pressure Control If the

unit is equipped with the low ambient temperature head pressure control option, field-fabricated and field-installed wind
baffles are required if the wind velocity is anticipated to be
greater than 5 mph (8 km/h). Two different baffles may be required, facing the control box. Wind baffles should be constructed with minimum 18-gage galvanized sheet metal or other suitable corrosion-resistance material with cross breaks for
strength. See Fig. 26. Use field-supplied screws to attach baffles to the corner posts of the machine. Be sure to hem or turn a
flange on all edges to eliminate sharp edges on the baffles.
To avoid damage to the refrigerant coils and electrical components, use extreme care when drilling screw holes and
screwing in fasteners.
Mount the smaller height baffle on units with a control box
located on the end of the unit. It is recommended that the upper
notches be used for mounting the baffles. This reduces the risk
of damaging the coil while drilling a mounting hole. Loosen
the upper corner post bolts and slide the baffle under the bolt
and washer. Tighten the bolt. Drill holes in the bottom of the
flange of the baffle and mount with two screws to secure the
bottom of the baffle to the corner post. Repeat the process for
the opposite end. See Fig. 26.
To avoid possibility of electrical shock, open all disconnects before installing or servicing this accessory.
Cross break these faces.

Hem these 3 edges both top
and bottom.
305 [12.0]
See Detail A
1880 [74.0]
180 [7.0]
BAFFLE HEIGHT (X)

RIGHT END LEFT END
POSITION
30XA080-120
(Facing the control box end)
30XA140-500
(Facing the control box end)
1040 [41.0]
635 [25.0]
1040 [41.0]
1040 [41.0]
18 [0.75]
NOTES:
1. Material: 18 ga. Corrosion Resistant Sheet Metal.
2. Dimensions are in mm [inches].
18 [0.75]
70 [2.75]
31 [1.25]
21 [0.88]
Detail A
Typical Both Flanges
Fig. 26 Field-Fabricated and Field-Installed Wind Baffles
47
a30-3997
Step 4 Fill the Chilled Water Loop
SYSTEM
IMPORTANT: Before starting unit, be sure all of the

air has been purged from the system.
SIDE
STREAM
FILTER
The chilled water pump (if equipped) is rated for 150 psig
(1034 kPa) duty. The maximum cooler fluidside pressure is
300 psig (2068 kPa). Check the pressure rating for all of the
chilled water devices installed. Do not exceed the lowest pressure rated device.
WATER SYSTEM CLEANING Proper water system
cleaning is of vital importance. Excessive particulates in the
water system can cause excessive pump seal wear, reduce or
stop flow, and cause damage of other components.
1. Install a temporary bypass around the chiller to avoid
circulating dirty water and particulates into the pump
package and chiller during the flush. Use a temporary
circulating pump during the cleaning process. Also, be
sure that there is capability to fully drain the system after
cleaning. See Fig. 27.
2. Be sure to use a cleaning agent that is compatible with
all system materials. Be especially careful if the system
contains any galvanized or aluminum components. Both
detergent-dispersant and alkaline-dispersant cleaning
agents are available.
3. It is recommended to fill the system through a water
meter. This provides a reference point for the future for
loop volume readings, and it also establishes the correct
quantity of cleaner needed in order to reach the required
concentration.
4. Use a feeder/transfer pump to mix the solution and fill the
system. Circulate the cleaning system for the length of
time recommended by the cleaning agent manufacturer.
a. After cleaning, drain the cleaning fluid and flush the
system with fresh water.
b. A slight amount of cleaning residue in the system can
help keep the desired, slightly alkaline, water pH of 8
to 9. Avoid a pH greater than 10, since this will
adversely affect pump seal components.
c. A side stream filter is recommended (see Fig. 28 during the cleaning process. Filter side flow rate should
be enough to filter the entire water volume every 3 to
4 hours. Change filters as often as necessary during
the cleaning process.
d. Remove temporary bypass when cleaning is complete.
A suction guide with an internal strainer is standard on all
30XA units with factory-installed hydronic packages. This
strainer allows removal of particulates from the chilled
water loop. Using the combination valve and the field-installed
isolation valve at the inlet, the strainer can be isolated from the
chilled water loop to be cleaned.
a30-4412
TO DRAIN
The Carrier ComfortLink controls provided have a builtin feature to remind building owners or operators to clean the
strainer at a pre-set time interval. Properly installed, cleaned
and maintained systems will rarely need the strainer cleaned
after the initial fill. This time interval is user-configurable.
Ideally, the chilled water loop will be cleaned before the unit
is connected. If the run-in screen is left in the suction guide/
strainer, it is recommended that the Service Maintenance be set
to alert the operator within 24 hours of start-up to be sure that
the run-in screen in the suction guide/strainer is removed after
24 hours of operation.
NOTE: The suction guide/strainer must be removed after the
first 24 hours of operation.
To set the time for the parameter, go to Time Clock/MCFG/
W.FIL in the handheld Navigator display. To set the time for
the parameter with the Touch Pilot display, go to Main
Menu/Service/MAINTCFG/wfilter_c. Values for this item are
input in days.
WATER TREATMENT Fill the fluid loop with water (or
brine) and a corrosion-resistant inhibitor suitable for the water
of the area. Consult the local water treatment specialist for
characteristics of system water and a recommended inhibitor
for the cooler fluid loop.
SYSTEM PRESSURIZATION A proper initial cold fill
pressure must be established before filling of the unit. The
initial cold fill pressure is the pressure applied at the filling
point to fill a system to its highest point, plus a minimum
pressure at the top of the system (4 psig minimum [27.6 kPa])
to operate air vents and positively pressurize the system. The
expansion tank is very important to system pressurization. The
expansion tank serves several purposes:
1. Provide NPSHR (Net Positive Suction Head Required)
for the pump to operate satisfactorily.
2. Set system pressure.
3. Accommodate expansion/contraction of water due to
temperature changes.
4. Acts as a pressure reference for the pump.
The expansion tank pressure must be set BEFORE the
system is filled. Follow the manufacturers recommendation
for instructions on setting the pressure in the expansion tank.
NPSHR information is provided on the Pump Curves in
Fig. 29-32 for units with factory-installed hydronic kits. See
Table 4 for pump impeller sizes.
Once the system is pressurized, the pressure at the connection point of the expansion tank to water piping will not change
unless the water loop volume changes (either due to addition/
subtraction of water or temperature expansion/contraction).
The pressure at this point remains the same regardless of
whether or not the pump is running.
30XA UNIT
TO DRAIN
TEMPORARY
BYPASS
Fig. 28 Cleaning Using a Side Stream Filter
a30-4411
30XA UNIT
POT FEEDER AND

TRANSFER PUMP
TEMPORARY
PUMP
POT FEEDER AND

TRANSFER PUMP
TEMPORARY
PUMP
SYSTEM
DILUTED
CLEANING
AGENT
DILUTED
CLEANING
AGENT
TEMPORARY
BYPASS
Fig. 27 Typical Set Up for Cleaning Process
48
2. Check to make sure all drain plugs are installed.

Normally, a closed system needs to be filled only once. The
actual filling process is a fairly simple procedure. All air should
be purged or vented from the system. Thorough venting at high
points and circulation at room temperature for several hours is
highly recommended.
NOTE: Local codes concerning backflow devices and other
protection of the city water system should be consulted and
followed to prevent contamination of the public water supply.
This is critical when anti-freeze is used in the system.
SET WATER FLOW RATE Once the system is cleaned,
pressurized, and filled, the flow rate through the chiller needs
to be established. On units with the hydronic package, this can
be accomplished by using the balancing valve. Follow the
manufacturers recommendations for setting the balancing
valve. Local codes may prohibit restricting the amount of water
using the balancing valve for a given motor horsepower. In this
case, use the method listed in the Pump Modification/
Trimming section. See below for the type of combination valve
in 30XA units with the optional hydronic package.
Since the expansion tank acts as a reference point for the

pump, there cannot be two reference points (two expansion
tanks) in a system, unless manifolded together. Where two or
more 30XA chillers with the hydronic option are installed in
parallel, there should not be more than one expansion tank in
the system, unless manifolded together as seen in Fig. 24. It is
permissible to install the expansion tank(s) in a portion of the
return water line that is common to all pumps, providing that
the tank is properly sized for combined system volume.
If the application involves two or more chillers in a primary
secondary system, a common place for mounting the expansion tank is in the chilled water return line, just before the
decoupler. See Fig. 24 for placement of expansion tank in
primary-secondary systems.
If a diaphragm expansion tank is utilized (a flexible
diaphragm physically separates the water/air interface) it is not
recommended to have any air in the water loop. See the section
on air separation on page 44 for instructions on providing air
separation equipment.
FILLING THE SYSTEM The initial fill of the chilled
water system must accomplish three goals:
1. The entire piping system must be filled with water.
2. The pressure at the top of the system must be high enough
to vent air from the system (usually 4 psig [27.6 kPa] is
adequate for most vents).
3. The pressure at all points in the system must be high
enough to prevent flashing in the piping or cavitation in
the pump.
The pressure created by an operating pump affects system
pressure at all points except one the connection of the
expansion tank to the system. This is the only location in the
system where pump operation will not give erroneous pressure
indications during the fill. Therefore, the best location to install
the fill connection is close to the expansion tank. An air vent
should be installed close by to help eliminate air that enters
during the fill procedure.
When filling the system, ensure the following:
1. Remove temporary bypass piping and cleaning/flushing
equipment.
30XA UNIT SIZE

090-160
SINGLE/DUAL PUMP
FTV-5 in.
NOTE: Carrier recommends a differential pressure gage when

measuring pressures across the pumps or balancing valves.
This provides for greater accuracy and reduces error build-up
that often occurs when subtracting pressures made by different
gages.
A rough estimate of water flow can also be obtained from
the pressure gages across the 30XA heat exchanger.
Figure 29 and 30 shows the relationship between gpm and
heat exchanger pressure drop. It should be noted that these
curves are for fresh water and clean heat exchangers; they do
not apply to heat exchangers with fouling. To read the chart,
subtract the readings of the two pressure gages on the hydronic
kit. This number is the pressure drop across the heat exchanger.
Adjust the factory-installed balancing valve or external balancing valve (in units without hydronic package) until the correct
pressure drop is obtained for the required flow.
Table 4 Pump Impeller Sizes

30XA
UNIT SIZE
PUMP
Hp
Option Code*
090-160
5
7.5
10
15
1
2
3
4
SINGLE PUMP
Impeller Dia.
Rpm
(in.)
3450
4.5
3450
5
3450
5.4
3450
6.1
Pump Curve
Option Code*
I
I
I
I
7
8
B
C
DUAL PUMP
Impeller Dia.
Rpm
(in.)
3450
4.5
3450
5
3450
5.4
3450
6.1
*Option Code refers to the Hydronics Option (position 11) in the model number. See Fig. 1 for option identification.
49
Pump Curve
II
II
II
II
30XA140
30XA090,100
160
140
Available Head (Feet)
Ava ilable Head (Feet)
160
120
100
80
60
40
20
0
0
100
200
300
400
140
120
3
100
80
60
40
20
0
500
GPM
100
300
400
500
400
500
GPM
a30-4431
a30-4434
30XA160
30XA110
160
160
140
Available Head (Feet )
Ava ilable Head (Feet)
200
120
100
80
2
1
60
40
20
0
0
100
200
300
400
140
120
3
100
80
60
40
20
0
500
GPM
100
200
300
GPM
a30-4432
a30-4435
30XA120
Selection
1
2
3
4
Ava ila bl e Head (Feet)
160
140
120
100
80
2
1
60
40
20
0
0
100
200
300
400
500
GPM
a30-4433
Fig. 29 30XA090-160 Single Pump Envelope Curves
50
Pump
Single 5HP
Single 7.5HP
Single 10HP
Single 15HP
30XA140
30XA090,100
160
160
140
C
140
120
100
80
60
40
120
B
100
80
60
40
20
20
0
0
100
200
300
400
500
100
200
a30-4436
500
30XA160
160
160
C
140
140
120
100
80
60
40
120
B
100
80
60
40
20
20
0
0
100
200
300
400
500
100
200
300
GPM
GPM
a30-4437
a30-4440
30XA120
Selection
7
8
B
C
160
140
400
a30-4439
30XA110
300
GPM
GPM
120
B
100
80
60
40
20
0
0
100
200
300
400
500
GPM
a30-4438
Fig. 30 30XA090-160 Dual Pump Envelope Curves
51
Pump
Dual 5HP
Dual 7.5HP
Dual 10HP
Dual 15HP
400
500
Head Pressure
(m) ft of Fluid
3450 RPM
(45.7) 150 6.19 in
39
52
62
70
5.75 in
74
77
(36.6) 120 5.50 in
77
77
5.25 in
74
5.00 in
70
(27.4) 90 4.75 in
62
4.50 in
20 hp
(18.3) 60
15 hp
52%
10 hp
(9.1) 30
N
P
S
H
r
(0.0) 0
a30-4441
0
0.00
7.5 hp
5 hp
3 hp
NPSHr
100
6.31
200
12.62
300
18.93
Flow Rate
400
25.24
500
31.54
(gpm)
(l/s)
LEGEND
NPSHr Net Positive Suction Head (Pressure) Required
NOTE: Refer to Fig. 1 for option identification. Refer to Table 4 for more information.
Fig. 31 Pump Curve I for Hydronic Package Single Pump (Fresh Water)
Head Pressure
(m) ft of Fluid
3450 RPM
(45.7) 150 6.19 in
39
52
62
70
5.75 in
74
77
(36.6) 120 5.50 in
77
5.25 in
77
74
5.00 in
70
(27.4) 90 4.75 in
62
4.50 in
20 hp
(18.3) 60
15 hp
52%
10 hp
(9.1) 30
N
P
S
H
r
(0.0) 0
a30-4442
0
0.00
7.5 hp
5 hp
3 hp
NPSHr
100
6.31
200
12.62
300
18.93
400
25.24
500
31.54
Flow Rate
LEGEND
NPSHr Net Positive Suction Head (Pressure) Required
NOTE: Refer to Fig. 1 for option identification. Refer to Table 4 for more information.
Fig. 32 Pump Curve II for Hydronic Package Dual Pump (Fresh Water)
52
(gpm)
(l/s)
NOTE: Do not use automobile anti-freeze, or any other fluid

that is not approved for heat exchanger duty. Only use appropriately inhibited glycols, concentrated to provide adequate
protection for the temperature considered.
Use an electric tape heater for the external piping, if unit
will be exposed to freezing temperatures.
Ensure that power is available to the chiller at all times,
even during the off-season, so that the pump and cooler heaters
have power. Also make sure that the piping tape heaters have
power.
On units with pump packages, a heater is supplied with the
hydronic package that will protect this section from freezing in
outdoor-air temperatures down to 20 F (29 C), except in the
case of a power failure. The Carrier warranty does not cover
damage due to freezing.
Cooler heaters that will protect components down to 20 F
(28.9 C) can be ordered as a factory-installed option. Again, it
should be noted that these heaters will not protect the cooler
from freezing in the event of a power failure. The Carrier
warranty does not cover damage due to freezing.
PREPARATION FOR WINTER SHUTDOWN If the unit
is not operational during the winter months, at the end of cooling
season complete the following steps.
PUMP MODIFICATION/TRIMMING Since the pumps

are constant speed, the only way to obtain greater flow with a
given pump/impeller is to decrease system head. This will
allow the pump to ride its curve to the right, resulting in
increased flow. If greater flow is necessary, consider opening
the combination valve. Also, verify that the strainer is clean,
and that no unnecessary system resistance is present, such as
partially closed isolation valves.
Once the combination valve is set, note the stem position. If
later service work requires the valve to be closed, it will be easier
to re-balance the system, if the original balance point is known.
Increasing system resistance by closing the balancing valve
will force the pump to ride its curve to the left, resulting in
less flow. Although this does reduce power consumption
slightly, it may not be the desirable method of reducing the
flow, especially if a large reduction is needed.
The other method for reducing flow on a constant speed
pump is impeller trimming. The impellers in the pumps provided in the 30XA hydronic kit can be easily removed for this
purpose. Refer to the vendor literature packet supplied with the
hydronic package information on Seal Replacement in the
Service Section, and follow instructions for impeller removal
and trimming. See Fig. 29 and 30 for pump envelope curve information. Trimming should only be done by a qualified machine shop that has experience in this operation. Contact your
local Carrier representative for a recommended machine shop.
Failure to remove power before draining heater equipped

coolers and hydronic packages can result in heater tape and
insulation damage.
After trimming, the impeller MUST be balanced. Failure to

balance trimmed impellers can result in excessive vibration, noise, and premature bearing failure.
1. If the unit has optional heater tapes on the cooler and the
cooler will not be drained, do not shut off power disconnect during off-season shutdown. If the unit has optional
heater tapes on the cooler and the cooler is drained, open
the circuit breaker for the heater, CB-13 or shut off power
during off-season shutdown.
2. Draining the fluid from the system is highly recommended. If the unit is equipped with a hydronic package, there
are additional drains in the pump housing and strainer
that must be opened to allow for all for all of the water to
drain.
3. Isolate the cooler from the rest of the system with water
shutoff valves.
4. Replace the drain plug and completely fill the cooler with
a mixture of water and a suitable corrosion-inhibited antifreeze solution such as propylene glycol. The concentration should be adequate to provide freeze protection to
15 F (8.3 C) below the expected low ambient temperature conditions. Anti-freeze can be added through the
vent on top of the cooler. If the unit has a hydronic pump
package, the pump must be treated in the same manner.
5. Leave the cooler filled with the antifreeze solution for the
winter, or drain if desired. Be sure to deenergize heaters
(if installed) as explained in Step 1 to prevent damage.
Use an approved method of disposal when removing antifreeze solution.
At the beginning of the next cooling season, be sure that
there is refrigerant pressure on each circuit before refilling
cooler, add recommended inhibitor, and reset the CB-HT (circuit breaker heater) (if opened) or restore power.
Impeller trimming has the added benefit of maximum bhp

(brake horsepower) savings, which can recover the cost
incurred by performing the impeller trimming.
FREEZE PROTECTION The 30XA units are provided
with a flow switch to protect against freezing situations that
occur from no water flow. While the flow switch is helpful in
preventing freezing during no-flow situations, it does not
protect the chiller in case of power failure during sub-freezing
ambient temperatures, or in other cases where water temperature falls below the freezing mark. Appropriate concentrations
of inhibited propylene or ethylene glycol or other suitable
inhibited antifreeze solution should be considered for chiller
protection where ambient temperatures are expected to fall
below 32 F (0 C). Consult local water treatment specialist on
characteristics of the system water and add a recommended
inhibitor to the chilled water. The Carrier warranty does not
cover damage due to freezing.
If the pump will be subjected to freezing temperatures, steps
must be taken to prevent freeze damage. If the pump will not
be used during this time, it is recommended to drain the pump
and hydronic package and these components are back-flushed
with inhibited glycol. Otherwise, a glycol-water solution
should be considered as the heat transfer fluid. Drains are located on the pump(s) and suction guide/strainer for units with hydronic kits. Units without hydronic kits have a drain plug
mounted on the bottom of the cooler head at each end of the
cooler.
53
The 30XA units require 1 or 2 power supplies, depending

on the unit and circuit voltage. See Tables 5-8 for chiller electrical data. Cooler and pump heaters, if factory-installed, are
wired in the control circuit. Heaters on chillers with the optional control transformer will be capable of operation only when
the main power supply to the chiller is on. On chillers with separate control power, the heaters are capable of operation whenever the control power is supplied.
FIELD CONTROL POWER CONNECTIONS (See
Fig. 33) All units require 115-1-60 control circuit power,
unless the control transformer option is installed.
Terminals TB5-1 and TB5-2 are provided for field installation of a chilled water (fluid) pump interlock (CWPI). The
chilled water (fluid) flow sensor (CWFS) is factory installed.
These devices are to be installed in series. Contacts must be
rated for dry-circuit applications capable of handling a 24-vac
at 50 mA load.
An accessory remote on-off switch can be wired into TB5-9
and TB5-10. Contacts must be rated for dry-circuit applications
capable of handling a 24-vac at 50 mA load.
Step 5 Make Electrical Connections
Electrical shock can cause personal injury and death. Shut

off all power to this equipment during installation. There
may be more than one disconnect switch. Tag all disconnect locations to alert others not to restore power until work
is completed.
POWER SUPPLY The electrical characteristics of the
available power supply must agree with the unit nameplate
rating. Supply voltage must be within the limits shown. See
Tables 5-11 for electrical and configuration data.
FIELD POWER CONNECTIONS (See Fig. 33) All power
wiring must comply with applicable local and national codes.
Install field-supplied, branch circuit fused disconnect(s) of a
type that can be locked off or open. Disconnect(s) must be located within sight and readily accessible from the unit in compliance with NEC Article 440-14 (U.S.A.). See Tables 5-11 for
unit electrical data.
IMPORTANT: The 30XA units have a factory-installed
option available for a non-fused disconnect for unit power
supply. If the unit is equipped with this option, all field
power wiring should be made to the non-fused disconnect
since no terminal blocks are supplied.
Do not use interlocks or other safety device contacts

connected between TB5-9 and TB5-10 as remote on-off.
Connection of safeties or other interlocks between these
2 terminals will result in an electrical bypass if the
ENABLE-OFF-REMOTE contact switch is in the
ENABLE position. If remote on-off unit control is required,
a field-supplied relay must be installed in the unit control
box and wired as shown in Fig. 33. Failure to wire the
remote on-off as recommended may result in tube freeze
damage.
Maximum wire size that the unit terminal block or nonfused disconnect will accept is 500 kcmil.
POWER WIRING All power wiring must comply with applicable local and national codes. Install field-supplied branch
circuit fused disconnect per NEC of a type that can be locked
OFF or OPEN. Disconnect must be within sight and readily accessible from the unit in compliance with NEC Article 440-14.
In the power box, 7/8 in. holes are provided for power entry.
The holes will need to bee enlarged to accept the appropriate
conduit. NEC also requires all conduits from a conditioned
space to the power box(es) be sealed to prevent airflow and
moisture into the control box.
Terminals 11 and 13 of TB5 are for control of the chilled

water pump 1 (PMP1) starter. Terminals 13 and 15 of TB5 are
for control of the chilled water pump 2 (PMP2) starter.
54
a30-4443
55
Fig. 33 Control and Power Wiring Schematic
Table 5 30XA080-350* Electrical Data, Single Point (Standard Condenser Fan Motors)
UNIT
30XA
080
090
100
110
120
140
160
180
200
220
240
260
280
300
325
350
UNIT VOLTAGE
Supplied
V-Hz
(3 Ph)
NUMBER
OF
COND
Min Max
REQD
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
460-60
575-60
380-60
460-60
575-60
380-60
460-60
575-60
380-60
460-60
575-60
380-60
460-60
575-60
380-60
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
414
518
342
414
518
342
414
518
342
414
518
342
414
518
342
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
506
633
418
506
633
418
506
633
418
506
633
418
506
633
418
6
6
6
6
6
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
10
10
10
10
10
10
10
10
10
10
12
12
12
12
12
12
12
12
12
12
13
13
13
13
13
13
13
13
13
13
15
15
15
16
16
16
16
16
16
18
18
18
18
18
18
NO HYDRONIC PACKAGE
ICF
Rec
MCA MOCP
Fuse
WD
XL
Size
315.5
400
484.2 1170.2
350
347.6
450
549.6 1338.6
400
157.7
200
242.1
585.1
175
121.2
150
191.9
465.9
150
183.5
250
289.7
704.7
225
334.0
450
499.1 1185.1
400
368.0
500
566.0 1355.0
450
167.0
225
249.6
592.6
200
128.5
175
197.8
471.8
150
194.5
250
298.6
713.6
225
364.6
500
536.7 1278.7
400
401.3
500
607.8 1461.8
450
182.3
250
268.4
639.4
200
139.5
175
211.7
508.7
175
212.7
250
321.7
770.7
250
405.7
500
536.7
450
446.2
600
607.8
500
202.4
250
268.4
639.4
225
155.5
200
211.7
508.7
175
236.4
300
321.7
770.7
300
438.6
600
569.6
500
482.2
600
643.8
600
218.4
300
284.4
655.4
250
168.4
225
224.5
521.5
200
255.3
350
340.6
789.6
300
534.7
800
796.7
700
588.5
800
906.1
700
267.3
400
398.4 1030.4
350
205.0
300
315.5
821.5
250
311.2
450
478.9 1243.9
350
621.1
800
997.6
700
682.8 1000 1136.1
800
309.7
450
498.4 1306.4
350
238.1
350
396.3 1042.3
300
361.1
500
598.9 1577.9
450
673.2
800
935.2
800
740.9 1000 1058.5
1000
336.6
450
467.6 1099.6
400
258.3
350
368.8
874.8
300
391.5
500
559.2 1324.2
450
769.6 1000 1146.0
1000
846.0 1000 1299.2
1000
383.9
500
572.6 1380.6
450
294.8
400
453.0 1099.0
350
447.2
600
685.0 1664.0
500
850.2 1200 1152.0
1000
935.1 1200 1305.9
1200
424.7
600
575.6 1383.6
500
326.3
450
455.4 1101.4
400
494.5
700
688.6 1667.6
600
910.0 1200 1211.8
1200
1001.1 1200 1371.8
1200
455.0
600
605.9 1413.9
600
349.6
450
478.7 1124.7
400
529.5
700
723.5 1702.5
600
516.5
700
777.6 1999.6
600
396.4
500
616.2 1594.2
450
600.2
800
933.9 2412.9
700
549.7
800
810.9 2032.9
700
422.1
600
641.9 1619.9
500
638.7
800
972.4 2451.4
800
610.9
800
810.9 2032.9
700
468.7
600
641.9 1619.9
600
710.3 1000
972.4 2451.4
800
624.3
800
885.5 2107.5
700
479.1
600
698.9 1676.9
600
724.7 1000 1058.4 2537.4
800
685.5
800
885.5 2107.5
800
525.7
700
698.9 1676.9
600
796.3 1000 1058.4 2537.4 1000
5 HP PUMP, 3450 RPM

ICF
MCA MOCP
WD
XL
350.0
385.7
175.0
134.9
204.2
380.6
419.0
190.3
145.9
222.4
421.7
463.9
210.4
161.9
246.1
454.6
499.9
226.4
174.8
265.0
550.7
606.2
275.3
211.4
320.9
637.1
700.5
317.7
244.5
370.8
450
500
225
175
250
500
500
250
175
300
500
600
250
225
300
600
600
300
225
350
800
800
400
300
450
800
1000
450
350
500
LEGEND
ICF
Instantaneous Current Flow
MCA Minimum Circuit Amps
MOCP Maximum Overcurrent Protection
WD
Wye-Delta
XL
Across-the-Line
*30XA400-500 units are not available with single point power.
NOTES:
1. Units are suitable for use on electrical systems where voltage supplied to the unit
terminals is not below or above the listed minimum and maximum limits. Maximum
allowable phase imbalance is: voltage, 2%; amps 10%.
2. Cooler heater is wired into the control circuit so it is always operable as long as the
control power supply disconnect is on, even if any safety device is open.
515.1
583.7
257.6
204.2
308.3
552.7
625.5
276.4
218.1
331.3
552.7
625.5
276.4
218.1
331.3
585.6
661.5
292.4
230.9
350.3
812.7
923.8
406.4
321.9
488.6
1013.6
1153.8
506.4
402.7
608.6
1201.1
1372.7
600.6
478.2
723.3
1294.7
1479.5
647.4
515.1
780.3
647.4
515.1
780.3
663.4
527.9
799.3
1038.4
827.9
1253.6
1314.4
1048.7
1587.6
Rec
Fuse
Size
400
450
200
150
225
450
500
225
175
250
500
600
250
200
300
500
600
250
200
300
700
700
350
250
400
800
800
400
300
450
7.5 HP PUMP, 3450 RPM

ICF
Rec
MCA MOCP
Fuse
WD
XL
Size
357.2
450
522.3 1208.3 400
393.6
500
591.7 1380.7 450
178.6
225
261.2
604.2 200
137.7
175
207.0
481.0 150
208.6
250
312.6
727.6 250
387.8
500
559.9 1301.9 450
427.0
500
633.5 1487.5 500
193.9
250
280.0
651.0 225
148.8
200
220.9
517.9 175
226.7
300
335.7
784.7 250
428.9
600
559.9
500
471.9
600
633.5
600
214.0
300
280.0
651.0 250
164.8
225
220.9
517.9 200
250.4
350
335.7
784.7 300
461.8
600
592.8
600
507.8
600
669.4
600
230.0
300
296.0
667.0 300
177.7
225
233.8
530.8 200
269.4
350
354.7
803.7 300
557.9
800
819.9
700
614.1
800
931.8
700
278.9
400
410.0 1042.0 350
214.3
300
324.7
830.7 250
325.3
450
493.0 1258.0 400
644.3
800 1020.8
800
708.5 1000 1161.7
800
321.3
450
510.0 1318.0 400
247.4
350
405.6 1051.6 300
375.2
500
612.9 1591.9 450
CONTROL CIRCUIT
Voltage
MCA
1 PH,
and
60 Hz
MOCP
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
3. For MCA that is less than or equal to 380 amps, 3 conductors are required.
For MCA between 381-760 amps, 6 conductors are required.
Calculation of conductors required is based on 75 C copper wire.
4. Wiring for main field supply must be rated 75 C minimum. Use copper for all units.
a. Incoming wire size range for the terminal block is no. 4 AWG (American Wire Gage)
to 500 kcmil.
b. Incoming wire size range of non-fused disconnect with MCA up to 599.9 amps is
3/0 to 500 kcmil.
c. Incoming wire size range of non-fused disconnect with MCA from 600 to 799.9 amps
is 1/0 to 500 kcmil.
d. Incoming wire size range of non-fused disconnect with MCA from 800 to 1199.9 amps
is 250 kcmil to 500 kcmil.
5. Data provided circuit 1/circuit 2 where there are two circuits.
56
Table 5 30XA080-350* Electrical Data, Single Point (Standard Condenser Fan Motors) (cont)
UNIT
30XA
080
090
100
110
120
140
160
180
200
220
240
260
280
300
325
350
UNIT VOLTAGE
Supplied
V-Hz
(3 Ph)
Min
Max
NUMBER
OF
COND
REQD
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
460-60
575-60
380-60
460-60
575-60
380-60
460-60
575-60
380-60
460-60
575-60
380-60
460-60
575-60
380-60
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
414
518
342
414
518
342
414
518
342
414
518
342
414
518
342
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
506
633
418
506
633
418
506
633
418
506
633
418
506
633
418
6
6
6
6
6
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
10
10
10
10
10
10
10
10
10
10
12
12
12
12
12
12
12
12
12
12
13
13
13
13
13
13
13
13
13
13
15
15
15
16
16
16
16
16
16
18
18
18
18
18
18
MCA
364.4
401.6
182.2
140.6
212.9
395.0
434.9
197.5
151.7
231.1
436.1
479.9
217.6
167.7
254.8
469.0
515.8
233.6
180.5
273.7
565.1
622.1
282.5
217.1
329.6
651.5
716.4
324.9
250.2
379.5
10 HP PUMP, 3450 RPM

ICF
MOCP
WD
XL
450
500
225
175
250
500
500
250
200
300
600
600
300
225
350
600
700
300
225
350
800
800
400
300
450
800
1000
450
350
500
529.5
599.6
264.8
209.9
317.0
567.1
641.5
283.6
223.8
340.1
567.1
641.5
283.6
223.8
340.1
600.0
677.4
299.6
236.7
359.0
827.1
939.7
413.6
327.6
497.3
1028.0
1169.7
513.6
408.5
617.3
1215.5
1388.6
607.8
483.9
732.0
1309.1
1495.5
654.6
520.8
789.1
654.6
520.8
789.1
670.6
533.7
808.0
1045.6
833.6
1262.3
1321.6
1054.5
1596.3
Rec
Fuse
Size
400
450
200
175
250
450
500
225
175
300
500
600
250
200
300
600
600
300
200
300
700
700
350
250
400
800
1000
400
300
450
MCA
379.0
417.7
189.5
146.5
221.8
409.6
451.1
204.8
157.5
239.9
450.7
496.0
224.9
173.5
263.6
483.6
531.9
240.9
186.4
282.6
579.7
638.2
289.8
223.0
338.5
666.1
732.6
332.2
256.1
388.4

ICF
MOCP
WD
XL
500
500
250
175
250
500
600
250
200
300
600
600
300
225
350
600
700
300
250
350
800
800
400
300
450
800
1000
450
350
500
544.1
615.8
272.1
215.8
325.8
581.7
657.6
290.9
229.7
348.9
581.7
657.6
290.9
229.7
348.9
614.6
693.5
306.9
242.5
367.9
841.7
955.9
420.9
333.5
506.2
1042.6
1185.8
520.9
414.3
626.1
1230.1
1404.8
615.1
489.8
740.8
1323.7
1511.6
661.9
526.7
797.9
661.9
526.7
797.9
677.9
539.5
816.9
1052.9
839.5
1271.2
1328.9
1060.3
1605.1
Rec
Fuse
Size
450
500
225
175
250
450
500
225
175
300
500
600
250
200
300
600
600
300
225
350
700
800
350
250
400
800
1000
400
300
450
CONTROL CIRCUIT
Voltage
MCA
1 PH,
and
60 Hz
MOCP
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40

to 500 kcmil.
3/0 to 500 kcmil.
LEGEND
ICF
MCA Minimum Circuit Amps
MOCP Maximum Overcurrent Protection
WD
Wye-Delta
XL
Across-the-Line
*30XA400-500 units are not available with single point power.
NOTES:
57
Table 6 30XA080-500 Electrical Data, Dual Point (Standard Condenser Fan Motors)
UNIT
30XA
080
090
100
110
120
140
160
180
200
220
240
260
280
300
325
350
400
450
500
ICF
MCA
MOCP
WD
XL
UNIT VOLTAGE NUMBER

OF
V-Hz Supplied
COND
(3 Ph) Min Max REQD
NO HYDRONIC PACKAGE
ICF
MOCP
WD
XL
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
460-60
575-60
380-60
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
414
518
342
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
506
633
418
3/3
3/3
3/3
3/3
3/3
4/4
4/4
4/4
4/4
4/4
4/4
4/4
4/4
4/4
4/4
4/4
4/4
4/4
4/4
4/4
4/4
4/4
4/4
4/4
4/4
6/4
6/4
6/4
6/4
6/4
6/4
6/4
6/4
6/4
6/4
6/6
6/6
6/6
6/6
6/6
6/6
6/6
6/6
6/6
6/6
7/6
7/6
7/6
7/6
7/6
7/6
7/6
7/6
7/6
7/6
9/6
9/6
9/6
173.3/173.3
190.9/190.9
86.6/ 86.6
66.5/ 66.5
100.7/100.7
182.9/182.9
201.5/201.5
91.4/ 91.4
70.3/ 70.3
106.5/106.5
199.9/199.9
220.0/220.0
99.9/ 99.9
76.4/ 76.4
116.5/116.5
241.0/199.9
264.9/220.0
120.0/ 99.9
92.5/ 76.4
140.2/116.5
241.0/241.0
264.9/264.9
120.0/120.0
92.5/ 92.5
140.2/140.2
370.0/199.9
407.2/220.0
185.0/ 99.9
141.9/ 76.4
215.1/116.5
423.5/241.0
465.6/264.9
211.3/120.0
162.2/ 92.5
246.0/140.2
370.0/370.0
407.2/407.2
185.0/185.0
141.9/141.9
215.1/215.1
423.5/423.5
465.6/465.6
211.3/211.3
162.2/162.2
246.0/246.0
504.2/423.5
554.7/465.6
252.1/211.3
193.7/162.2
293.3/246.0
504.2/498.2
554.7/548.0
252.1/249.1
193.7/191.3
293.3/289.7
343.9/211.3
263.8/162.2
399.0/246.0
250/
300/
125/
110/
150/
300/
300/
150/
110/
175/
300/
350/
150/
125/
175/
400/
450/
200/
150/
225/
400/
450/
200/
150/
225/
600/
700/
300/
225/
350/
700/
800/
350/
250/
400/
600/
700/
300/
225/
350/
700/
800/
350/
250/
400/
800/
800/
400/
300/
500/
800/
800/
400/
300/
500/
500/
450/
600/
250
300
125
110
150
300
300
150
110
175
300
350
150
125
175
300
350
150
125
175
400
450
200
150
225
300
350
150
125
175
400
450
200
150
225
600
700
300
225
350
700
800
350
250
400
700
800
350
250
400
800
800
400
300
500
350
250
400
342.0/342.0
392.9/392.9
171.0/171.0
137.2/137.2
206.9/206.9
348.0/348.0
399.5/399.5
174.0/174.0
139.6/139.6
210.5/210.5
372.0/372.0
426.5/426.5
186.0/186.0
148.6/148.6
225.5/225.5
372.0/372.0
426.5/426.5
186.0/186.0
148.6/148.6
225.5/225.5
372.0/372.0
426.5/426.5
186.0/186.0
148.6/148.6
225.5/225.5
632.0/372.0
724.8/426.5
316.0/186.0
252.4/148.6
382.8/225.5
800.0/372.0
918.8/426.5
400.0/186.0
320.4/148.6
483.8/225.5
632.0/632.0
724.8/724.8
316.0/316.0
252.4/252.4
382.8/382.8
800.0/800.0
918.8/918.8
400.0/400.0
320.4/320.4
483.8/483.8
806.0/800.0
925.4/918.8
403.0/400.0
322.8/320.4
487.4/483.8
806.0/800.0
925.4/918.8
403.0/400.0
322.8/320.4
487.4/483.8
605.0/400.0
483.6/320.4
732.7/483.8
1028.0/1028.0
1181.9/1181.9
514.0/ 514.0
411.2/ 411.2
621.9/ 621.9
1034.0/1034.0
1188.5/1188.5
517.0/ 517.0
413.6/ 413.6
625.5/ 625.5
1114.0/1114.0
1280.5/1280.5
557.0/ 557.0
445.6/ 445.6
674.5/ 674.5
557.0/557.0
445.6/445.6
674.5/674.5
557.0/557.0
445.6/445.6
674.5/674.5
948.0/557.0
758.4/445.6
1147.8/674.5
1208.0/557.0
966.4/445.6
1462.8/674.5
948.0/ 948.0
758.4/ 758.4
1147.8/1147.8
1208.0/1208.0
966.4/ 966.4
1462.8/1462.8
1211.0/1208.0
968.8/ 966.4
1466.4/1462.8
1211.0/1208.0
968.8/ 966.4
1466.4/1462.8
1827.0/1208.0
1461.6/ 966.4
2211.7/1462.8
Rec
Fuse
Size
225/225
250/250
110/110
80/ 80
125/125
225/225
250/250
110/110
90/ 90
125/125
250/250
300/300
125/125
90/ 90
150/150
300/250
350/300
150/125
110/ 90
175/150
300/300
350/350
150/150
110/110
175/175
450/250
500/300
225/125
175/ 90
300/150
600/300
600/350
250/150
200/110
300/175
450/450
500/500
225/225
175/175
300/300
600/600
600/600
250/250
200/200
300/300
600/600
700/600
300/250
250/200
350/300
600/600
700/700
300/300
250/250
350/350
450/250
350/200
500/300
460-60
575-60
380-60
460-60
575-60
380-60
460-60
575-60
380-60
460-60
575-60
380-60
460-60
575-60
380-60
460-60
575-60
380-60
460-60
575-60
380-60
414
518
342
414
518
342
414
518
342
414
518
342
414
518
342
414
518
342
414
518
342
506
633
418
506
633
418
506
633
418
506
633
418
506
633
418
506
633
418
506
633
418
9/7
9/7
9/7
10/6
10/6
10/6
9/9
9/9
9/9
9/9
9/9
9/9
8/12
8/12
8/12
8/14
8/14
8/14
8/14
8/14
8/14
343.9/252.1
263.8/193.7
399.0/293.3
408.0/249.1
312.8/191.3
474.2/289.7
343.9/343.9
263.8/263.8
399.0/399.0
405.0/343.9
310.4/263.8
470.5/399.0
340.9/452.0
261.4/347.2
395.4/525.8
402.0/553.6
308.0/424.4
466.9/643.3
402.0/604.9
308.0/463.9
466.9/703.0
500/ 400
450/ 300
600/ 500
700/ 400
500/ 300
800/ 500
500/ 500
450/ 450
600/ 600
700/ 500
500/ 450
800/ 600
500/ 600
450/ 450
600/ 700
700/ 800
500/ 600
800/ 800
700/ 800
500/ 600
800/1000
605.0/403.0
483.6/322.8
732.7/487.4
608.0/400.0
486.0/320.4
736.3/483.8
605.0/605.0
483.6/483.6
732.7/732.7
605.0/605.0
483.6/483.6
732.7/732.7
602.0/602.9
481.2/476.3
729.1/719.9
602.0/753.6
481.2/597.6
729.1/905.5
602.0/804.9
481.2/637.1
729.1/965.2
1827.0/1211.0
1461.6/ 968.8
2211.7/1466.4
1830.0/1208.0
1464.0/ 966.4
2215.3/1462.8
1827.0/1827.0
1461.6/1461.6
2211.7/2211.7
1827.0/1827.0
1461.6/1461.6
2211.7/2211.7
1824.0/1410.9
1459.2/1122.3
2208.1/1698.9
1824.0/1975.6
1459.2/1575.6
2208.1/2384.5
1824.0/2026.9
1459.2/1615.1
2208.1/2444.2
450/300
350/250
500/350
500/300
400/250
600/350
450/450
350/350
500/500
500/450
400/350
600/500
450/500
350/400
500/600
500/700
400/500
600/800
500/700
400/600
600/800
MCA
LEGEND
Minimum Circuit Amps
Maximum Overcurrent Protection
Wye-Delta
Across-the-Line
5 HP PUMP, 3450 RPM

ICF
MOCP
WD
XL
182.9/198.9
201.5/219.2
91.4/ 99.4
70.3/ 76.7
106.5/116.1
199.9/215.9
220.0/237.7
99.9/107.9
76.4/ 82.8
116.5/126.2
241.0/215.9
264.9/237.7
120.0/107.9
92.5/ 82.8
140.2/126.2
241.0/257.0
264.9/282.6
120.0/128.0
92.5/ 98.9
140.2/149.9
370.0/215.9
407.2/237.7
185.0/107.9
141.9/ 82.8
215.1/126.2
423.5/257.0
465.6/282.6
211.3/128.0
162.2/ 98.9
246.0/149.9
300/300
300/350
150/150
110/125
175/175
300/350
350/350
150/175
125/125
175/200
400/350
450/350
200/175
150/125
225/200
400/400
450/450
200/200
150/150
225/250
600/350
700/350
300/175
225/125
350/200
700/400
800/450
350/200
250/150
400/250
348.0/364.0
399.5/417.2
174.0/182.0
139.6/146.0
210.5/220.2
372.0/388.0
426.5/444.2
186.0/194.0
148.6/155.0
225.5/235.2
372.0 /388.0
426.5/444.2
186.0/194.0
148.6/155.0
225.5/235.2
372.0/388.0
426.5/444.2
186.0/194.0
148.6/155.0
225.5/235.2
632.0/388.0
724.8/444.2
316.0/194.0
252.4/155.0
382.8/235.2
800.0/388.0
918.8/444.2
400.0/194.0
320.4/155.0
483.8/235.2
1034.0/1050.0
1188.5/1206.2
517.0/ 525.0
413.6/ 420.0
625.5/ 635.2
1114.0/1130.0
1280.5/1298.2
557.0/ 565.0
445.6/ 452.0
674.5/ 684.2
557.0/ 565.0
445.6/ 452.0
674.5/ 684.2
557.0/ 565.0
445.6/ 452.0
674.5/ 684.2
948.0/ 565.0
758.4/ 452.0
1147.8/ 684.2
1208.0/ 565.0
966.4/ 452.0
1462.8/ 684.2
Rec
Fuse
Size
225/250
250/300
110/125
90/ 90
125/150
250/300
300/300
125/150
90/100
150/150
300/300
350/300
150/150
110/100
175/150
300/350
350/350
150/150
110/125
175/200
450/300
500/300
225/150
175/100
300/150
600/350
600/350
250/150
200/125
300/200
MCA
CONTROL CIRCUIT
Voltage
MCA
1 PH,
and
60 Hz
MOCP
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
40
40
40
40
40
40
40
40
40
40
40
40
50
50
50
50
50
50
50
50
50

to 500 kcmil.
3/0 to 500 kcmil.
NOTES:
58
Table 6 30XA080-500 Electrical Data, Dual Point (Standard Condenser Fan Motors) (cont)
UNIT
30XA
080
090
100
110
120
140
160
180
200
220
240
260
280
300
325
350
400
450
500
ICF
MCA
MOCP
WD
XL
UNIT VOLTAGE
Supplied

ICF
MOCP
WD
XL
V-Hz
(3 Ph)
NUMBER
OF
COND
Min Max
REQD
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
460-60
575-60
380-60
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
414
518
342
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
506
633
418
3/3
3/3
3/3
3/3
3/3
4/4
4/4
4/4
4/4
4/4
4/4
4/4
4/4
4/4
4/4
4/4
4/4
4/4
4/4
4/4
4/4
4/4
4/4
4/4
4/4
6/4
6/4
6/4
6/4
6/4
6/4
6/4
6/4
6/4
6/4
6/6
6/6
6/6
6/6
6/6
6/6
6/6
6/6
6/6
6/6
7/6
7/6
7/6
7/6
7/6
7/6
7/6
7/6
7/6
7/6
9/6
9/6
9/6
182.9/206.1
201.5/227.1
91.4/103.0
70.3/ 79.6
106.5/120.5
199.9/223.1
220.0/245.7
99.9/111.5
76.4/ 85.7
116.5/130.6
241.0/223.1
264.9/245.7
120.0/111.5
92.5/ 85.7
140.2/130.6
241.0/264.2
264.9/290.6
120.0/131.6
92.5/101.8
140.2/154.3
370.0/223.1
407.2/245.7
185.0/111.5
141.9/ 85.7
215.1/130.6
423.5/264.2
465.6/290.6
211.3/131.6
162.2/101.8
246.0/154.3
300/300
300/350
150/150
110/125
175/175
300/350
350/400
150/175
125/125
175/200
400/350
450/400
200/175
150/125
225/200
400/400
450/450
200/200
150/150
225/250
600/350
700/400
300/175
225/125
350/200
700/400
800/450
350/200
250/150
400/250
348.0/371.2
399.5/425.2
174.0/185.6
139.6/148.9
210.5/224.6
372.0/395.2
426.5/452.2
186.0/197.6
148.6/157.9
225.5/239.6
372.0/395.2
426.5/452.2
186.0/197.6
148.6/157.9
225.5/239.6
372.0/395.2
426.5/452.2
186.0/197.6
148.6/157.9
225.5/239.6
632.0/395.2
724.8/452.2
316.0/197.6
252.4/157.9
382.8/239.6
800.0/395.2
918.8/452.2
400.0/197.6
320.4/157.9
483.8/239.6
460-60
575-60
380-60
460-60
575-60
380-60
460-60
575-60
380-60
460-60
575-60
380-60
460-60
575-60
380-60
460-60
575-60
380-60
460-60
575-60
380-60
414
518
342
414
518
342
414
518
342
414
518
342
414
518
342
414
518
342
414
518
342
506
633
418
506
633
418
506
633
418
506
633
418
506
633
418
506
633
418
506
633
418
9/7
9/7
9/7
10/6
10/6
10/6
9/9
9/9
9/9
9/9
9/9
9/9
8/12
8/12
8/12
8/14
8/14
8/14
8/14
8/14
8/14
MCA

ICF
MOCP
WD
XL
1034.0/1057.2
1188.5/1214.2
517.0/ 528.6
413.6/ 422.9
625.5/ 639.6
1114.0/1137.2
1280.5/1306.2
557.0/ 568.6
445.6/ 454.9
674.5/ 688.6
557.0/ 568.6
445.6/ 454.9
674.5/ 688.6
557.0/ 568.6
445.6/ 454.9
674.5/ 688.6
948.0/ 568.6
758.4/ 454.9
1147.8/ 688.6
1208.0/ 568.6
966.4/ 454.9
1462.8/ 688.6
Rec
Fuse
Size
225/250
250/300
110/125
90/100
125/150
250/300
300/300
125/150
90/100
150/175
300/300
350/300
150/150
110/100
175/175
300/350
350/350
150/175
110/125
175/200
450/300
500/300
225/150
175/100
300/175
600/350
600/350
250/175
200/125
300/200
182.9/213.3
201.5/235.1
91.4/106.6
70.3/ 82.5
106.5/124.9
199.9/230.3
220.0/253.6
99.9/115.1
76.4/ 88.6
116.5/134.9
241.0/230.3
264.9/253.6
120.0/115.1
92.5/ 88.6
140.2/134.9
241.0/271.4
264.9/298.5
120.0/135.2
92.5/104.6
140.2/158.6
370.0/230.3
407.2/253.6
185.0/115.1
141.9/ 88.6
215.1/134.9
423.5/271.4
465.6/298.5
211.3/135.2
162.2/104.6
246.0/158.6
300/300
300/350
150/150
110/125
175/175
300/350
350/400
150/175
125/125
175/200
400/350
450/400
200/175
150/125
225/200
400/400
450/450
200/200
150/150
225/250
600/350
700/400
300/175
225/125
350/200
700/400
800/450
350/200
250/150
400/250
348.0/378.4
399.5/433.2
174.0/189.2
139.6/151.8
210.5/228.9
372.0/402.4
426.5/460.2
186.0/201.2
148.6/160.8
225.5/243.9
372.0/402.4
426.5/460.2
186.0/201.2
148.6/160.8
225.5/243.9
372.0/402.4
426.5/460.2
186.0/201.2
148.6/160.8
225.5/243.9
632.0/402.4
724.8/460.2
316.0/201.2
252.4/160.8
382.8/243.9
800.0/402.4
918.8/460.2
400.0/201.2
320.4/160.8
483.8/243.9
1034.0/1064.4
1188.5/1222.2
517.0/ 532.2
413.6/ 425.8
625.5/ 643.9
1114.0/1144.4
1280.5/1314.2
557.0/ 572.2
445.6/ 457.8
674.5/ 692.9
557.0/ 572.2
445.6/ 457.8
674.5/ 692.9
557.0/ 572.2
445.6/ 457.8
674.5/ 692.9
948.0/ 572.2
758.4/ 457.8
1147.8/ 692.9
1208.0/ 572.2
966.4/ 457.8
1462.8/ 692.9
Rec
Fuse
Size
225/250
250/300
110/125
90/100
125/150
250/300
300/300
125/150
90/110
150/175
300/300
350/300
150/150
110/110
175/175
300/350
350/350
150/175
110/125
175/200
450/300
500/300
225/150
175/110
300/175
600/350
600/350
250/175
200/125
300/200
LEGEND
Wye-Delta
Across-the-Line
MCA
CONTROL CIRCUIT
Voltage
MCA
1 PH,
and
60 Hz
MOCP
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
40
40
40
40
40
40
40
40
40
40
40
40
50
50
50
50
50
50
50
50
50

to 500 kcmil.
3/0 to 500 kcmil.
NOTES:
59
Table 6 30XA080-500 Electrical Data, Dual Point (Standard Condenser Fan Motors) (cont)
UNIT
30XA
080
090
100
110
120
140
160
180
200
220
240
260
280
300
325
350
400
450
500
ICF
MCA
MOCP
WD
XL
UNIT VOLTAGE
Supplied
V-Hz
(3 Ph)
Min
Max
NUMBER
OF
COND
REQD
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
460-60
575-60
380-60
460-60
575-60
380-60
460-60
575-60
380-60
460-60
575-60
380-60
460-60
575-60
380-60
460-60
575-60
380-60
460-60
575-60
380-60
460-60
575-60
380-60
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
414
518
342
414
518
342
414
518
342
414
518
342
414
518
342
414
518
342
414
518
342
414
518
342
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
506
633
418
506
633
418
506
633
418
506
633
418
506
633
418
506
633
418
506
633
418
506
633
418
3/3
3/3
3/3
3/3
3/3
4/4
4/4
4/4
4/4
4/4
4/4
4/4
4/4
4/4
4/4
4/4
4/4
4/4
4/4
4/4
4/4
4/4
4/4
4/4
4/4
6/4
6/4
6/4
6/4
6/4
6/4
6/4
6/4
6/4
6/4
6/6
6/6
6/6
6/6
6/6
6/6
6/6
6/6
6/6
6/6
7/6
7/6
7/6
7/6
7/6
7/6
7/6
7/6
7/6
7/6
9/6
9/6
9/6
9/7
9/7
9/7
10/6
10/6
10/6
9/9
9/9
9/9
9/9
9/9
9/9
8/12
8/12
8/12
8/14
8/14
8/14
8/14
8/14
8/14

ICF
MCA
MOCP
182.9/227.9
201.5/251.2
91.4/113.9
70.3/ 88.3
106.5/133.7
199.9/244.9
220.0/269.8
99.9/122.4
76.4/ 94.4
116.5/143.8
241.0/244.9
264.9/269.8
120.0/122.4
92.5/ 94.4
140.2/143.8
241.0/286.0
264.9/314.7
120.0/142.5
92.5/110.5
140.2/167.5
370.0/244.9
407.2/269.8
185.0/122.4
141.9/ 94.4
215.1/143.8
423.5/286.0
465.6/314.7
211.3/142.5
162.2/110.5
246.0/167.5
300/350
300/350
150/175
110/125
175/200
300/350
350/400
150/175
125/125
175/225
400/350
450/400
200/175
150/125
225/225
400/450
450/500
200/225
150/175
225/250
600/350
700/400
300/175
225/125
350/225
700/450
800/500
350/225
250/175
400/250
LEGEND
Wye-Delta
Across-the-Line
WD
XL
348.0/393.0
399.5/449.3
174.0/196.5
139.6/157.6
210.5/237.8
372.0/417.0
426.5/476.3
186.0/208.5
148.6/166.6
225.5/252.8
372.0/417.0
426.5/476.3
186.0/208.5
148.6/166.6
225.5/252.8
372.0/417.0
426.5/476.3
186.0/208.5
148.6/166.6
225.5/252.8
632.0/417.0
724.8/476.3
316.0/208.5
252.4/166.6
382.8/252.8
800.0/417.0
918.8/476.3
400.0/208.5
320.4/166.6
483.8/252.8
1034.0/1079.0
1188.5/1238.3
517.0/ 539.5
413.6/ 431.6
625.5/ 652.8
1114.0/1159.0
1280.5/1330.3
557.0/ 579.5
445.6/ 463.6
674.5/ 701.8
557.0/ 579.5
445.6/ 463.6
674.5/ 701.8
557.0/ 579.5
445.6/ 463.6
674.5/ 701.8
948.0/ 579.5
758.4/ 463.6
1147.8/ 701.8
1208.0/ 579.5
966.4/ 463.6
1462.8/ 701.8
Rec
Fuse
Size
225/300
250/300
110/150
90/110
125/175
250/300
300/350
125/150
90/110
150/175
300/300
350/350
150/150
110/110
175/175
300/350
350/400
150/175
110/150
175/200
450/300
500/350
225/150
175/110
300/175
600/350
600/400
250/175
200/150
300/200
CONTROL CIRCUIT
Voltage
MCA
1 PH,
and
60 Hz
MOCP
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
50
115
50
115
50
115
50
115
50
115
50
115
50
115
50
115
50

to 500 kcmil.
3/0 to 500 kcmil.
NOTES:
60
Table 7 30XA140-500 Electrical Data, Single Point (High Ambient Option)

UNIT
30XA
140
160
180
200
220
240
260
280
300
325
350
ICF
MCA
MOCP
WD
XL
UNIT VOLTAGE
Supplied
V-Hz
(3 Ph)
Min Max
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
460-60
575-60
380-60
460-60
575-60
380-60
460-60
575-60
380-60
460-60
575-60
380-60
460-60
575-60
380-60
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
414
518
342
414
518
342
414
518
342
414
518
342
414
518
342
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
506
633
418
506
633
418
506
633
418
506
633
418
506
633
418
NUMBER
OF
COND
REQD
10
10
10
10
10
10
10
10
10
10
12
12
12
12
12
12
12
12
12
12
13
13
13
13
13
13
13
13
13
13
15
15
15
16
16
16
16
16
16
18
18
18
18
18
18
NO HYDRONIC PACKAGE
ICF
Rec
MCA MOCP
Fuse
WD
XL
Size
562.0
800
838.9
700
618.8
800
952.8
700
281.0
400
419.5 1051.5
350
216.3
300
332.5
838.5
250
328.3
450
504.6 1269.6
400
642.7
800 1036.7
800
706.9 1000 1179.4
800
320.5
450
518.0 1326.0
400
247.2
350
412.1 1058.1
300
374.9
500
622.8 1601.8
450
703.9
800
980.8
800
775.0 1000 1109.1
1000
351.9
450
490.4 1122.4
400
271.1
350
387.3
893.3
300
410.8
500
587.2 1352.2
450
795.6 1000 1189.6
1000
875.0 1200 1347.5
1000
396.9
500
594.4 1402.4
450
305.8
400
470.7 1116.7
350
463.8
600
711.7 1690.7
600
876.7 1200 1200.4
1000
964.6 1200 1359.4
1200
438.0
600
599.8 1407.8
500
337.6
450
475.0 1121.0
400
511.5
700
718.3 1697.3
600
933.0 1200 1256.7
1200
1026.7 1200 1421.6
1200
466.5
600
628.3 1436.3
600
359.5
450
497.0 1143.0
400
544.4
700
751.2 1730.2
600
529.1
700
806.6 2028.6
600
407.4
500
639.7 1617.7
500
616.7
800
969.3 2448.3
700
563.0
800
840.5 2062.5
700
433.6
600
665.9 1643.9
500
656.2
800 1008.8 2487.8
800
619.6
800
840.5 2062.5
700
476.7
600
665.9 1643.9
600
722.3 1000 1008.8 2487.8 1000
638.1
800
915.6 2137.6
700
491.2
600
723.5 1701.5
600
743.0 1000 1095.6 2574.6 1000
694.6
800
915.6 2137.6
800
534.2
700
723.5 1701.5
600
809.1 1000 1095.6 2574.6 1000
5 HP PUMP, 3450 RPM

ICF
MCA MOCP
WD
XL
578.0
636.5
289.0
222.7
338.0
658.7
724.5
328.5
253.6
384.6
800
800
400
300
450
800
1000
450
350
500
LEGEND
Wye-Delta
Across-the-Line
854.9
970.5
427.5
338.9
514.3
1052.7
1197.1
526.0
418.5
632.5
1059.5
844.9
1279.3
1334.0
1064.5
1611.5
Rec
Fuse
Size
700
800
350
250
400
800
1000
400
300
450

ICF
Rec
MCA MOCP
Fuse
WD
XL
Size
585.2
800
862.1
700
644.4
800
978.5
800
292.6
400
431.1 1063.1
350
225.6
300
341.8
847.8
250
342.3
450
518.7 1283.7
400
665.9
800 1059.9
800
732.5 1000 1205.0
1000
332.1
450
529.6 1337.6
400
256.5
350
421.4 1067.4
300
388.9
500
636.8 1615.8
450
CONTROL CIRCUIT
Voltage
MCA
1 PH,
and
60 Hz
MOCP
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40

to 500 kcmil.
3/0 to 500 kcmil.
NOTES:
61
Table 7 30XA140-500 Electrical Data, Single Point (High Ambient Option) (cont)
UNIT VOLTAGE
Supplied
UNIT
30XA
140
160
180
200
220
240
260
280
300
325
350
ICF
MCA
MOCP
WD
XL
V-Hz
(3 Ph)
Min
Max
NUMBER
OF
COND
REQD
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
460-60
575-60
380-60
460-60
575-60
380-60
460-60
575-60
380-60
460-60
575-60
380-60
460-60
575-60
380-60
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
414
518
342
414
518
342
414
518
342
414
518
342
414
518
342
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
506
633
418
506
633
418
506
633
418
506
633
418
506
633
418
10
10
10
10
10
10
10
10
10
10
12
12
12
12
12
12
12
12
12
12
13
13
13
13
13
13
13
13
13
13
15
15
15
16
16
16
16
16
16
18
18
18
18
18
18
MCA
592.4
652.4
296.2
228.4
346.7
673.1
740.5
335.7
259.4
393.3

ICF
MOCP
WD
XL
800
800
400
300
450
800
1000
450
350
500
869.3
986.5
434.7
344.6
523.0
1067.1
1213.0
533.2
424.3
641.2
1066.7
850.6
1288.0
1341.2
1070.3
1620.2
LEGEND
Wye-Delta
Across-the-Line
Rec
Fuse
Size
700
800
350
300
400
800
1000
400
300
450
MCA
607.0
668.6
303.5
234.3
355.5
687.7
756.6
343.0
265.2
402.1

ICF
MOCP
WD
XL
800
800
400
300
500
800
1000
450
350
500
883.9
1002.6
442.0
350.5
531.9
1081.7
1229.1
540.5
430.1
650.0
1074.0
856.5
1296.9
1348.5
1076.1
1629.0
Rec
Fuse
Size
700
800
350
300
400
800
1000
400
300
450
CONTROL CIRCUIT
Voltage
MCA
1 PH,
and
60 Hz
MOCP
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40

to 500 kcmil.
3/0 to 500 kcmil.
NOTES:
62
Table 8 30XA140-500 Electrical Data, Dual Point (High Ambient Option)

UNIT
30XA
140
160
180
200
220
240
260
280
300
325
350
400
450
500
ICF
MCA
MOCP
WD
XL
UNIT VOLTAGE
Supplied
V-Hz
(3 Ph)
NUMBER
OF
COND
Min Max REQD
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
460-60
575-60
380-60
460-60
575-60
380-60
460-60
575-60
380-60
460-60
575-60
380-60
460-60
575-60
380-60
460-60
575-60
380-60
460-60
575-60
380-60
460-60
575-60
380-60
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
414
518
342
414
518
342
414
518
342
414
518
342
414
518
342
414
518
342
414
518
342
414
518
342
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
506
633
418
506
633
418
506
633
418
506
633
418
506
633
418
506
633
418
506
633
418
506
633
418
6/4
6/4
6/4
6/4
6/4
6/4
6/4
6/4
6/4
6/4
6/6
6/6
6/6
6/6
6/6
6/6
6/6
6/6
6/6
6/6
7/6
7/6
7/6
7/6
7/6
7/6
7/6
7/6
7/6
7/6
9/6
9/6
9/6
9/7
9/7
9/7
10/6
10/6
10/6
9/9
9/9
9/9
9/9
9/9
9/9
8/12
8/12
8/12
8/14
8/14
8/14
8/14
8/14
8/14
MCA
383.8/211.9
422.6/233.3
191.9/105.9
147.7/ 81.4
223.9/124.0
434.8/249.1
478.1/273.9
216.9/124.1
167.0/ 95.9
253.3/145.4
383.8/383.8
422.6/422.6
191.9/191.9
147.7/147.7
223.9/223.9
434.8/434.8
478.1/478.1
216.9/216.9
167.0/167.0
253.3/253.3
515.9/434.8
567.8/478.1
258.0/216.9
198.8/167.0
301.0/253.3
515.9/505.1
567.8/555.8
258.0/252.6
198.8/194.5
301.0/294.5
349.1/216.9
268.6/167.0
406.2/253.3
349.1/258.0
268.6/198.8
406.2/301.0
411.0/252.6
315.9/194.5
478.9/294.5
349.1/349.1
268.6/268.6
406.2/406.2
405.6/349.1
311.6/268.6
472.4/406.2
343.7/461.1
264.2/355.2
399.7/537.9
400.2/560.2
307.3/430.7
465.8/652.8
400.2/608.8
307.3/468.0
465.8/709.3
NO HYDRONIC PACKAGE
ICF
MOCP
WD
XL
600/ 300
700/ 350
300/ 150
225/ 125
350/ 200
700/ 400
800/ 450
350/ 200
250/ 150
400/ 225
600/ 600
700/ 700
300/ 300
225/ 225
350/ 350
700/ 700
800/ 800
350/ 350
250/ 250
400/ 400
800/ 700
800/ 800
400/ 350
300/ 250
500/ 400
800/ 800
800/ 800
400/ 400
300/ 300
500/ 450
500/ 350
450/ 250
600/ 400
500/ 400
450/ 300
600/ 500
600/ 400
500/ 300
800/ 450
500/ 500
450/ 450
600/ 600
600/ 500
500/ 450
800/ 600
500/ 600
400/ 450
600/ 700
600/ 800
500/ 600
700/ 800
600/ 800
500/ 600
700/1000
660.8/391.2
756.7/447.8
330.4/195.6
263.9/156.3
400.2/237.1
828.8/391.2
950.7/447.8
414.4/195.6
331.9/156.3
501.2/237.1
660.8/660.8
756.7/756.7
330.4/330.4
263.9/263.9
400.2/400.2
828.8/828.8
950.7/950.7
414.4/414.4
331.9/331.9
501.2/501.2
839.6/828.8
962.6/950.7
419.8/414.4
336.2/331.9
507.8/501.2
839.6/828.8
962.6/950.7
419.8/414.4
336.2/331.9
507.8/501.2
626.6/414.4
500.9/331.9
758.8/501.2
626.6/419.8
500.9/336.2
758.8/507.8
632.0/414.4
505.2/331.9
765.4/501.2
626.6/626.6
500.9/500.9
758.8/758.8
626.6/626.6
500.9/500.9
758.8/758.8
621.2/622.9
496.6/492.7
752.3/744.6
621.2/781.2
496.6/619.9
752.3/939.2
621.2/829.7
496.6/657.3
752.3/995.7
962.4/ 566.6
769.9/ 453.3
1165.2/ 686.1
1222.4/ 566.6
977.9/ 453.3
1480.2/ 686.1
962.4/ 962.4
769.9/ 769.9
1165.2/1165.2
1222.4/1222.4
977.9/ 977.9
1480.2/1480.2
1227.8/1222.4
982.2/ 977.9
1486.8/1480.2
1227.8/1222.4
982.2/ 977.9
1486.8/1480.2
1848.6/1222.4
1478.9/ 977.9
2237.8/1480.2
1848.6/1227.8
1478.9/ 982.2
2237.8/1486.8
1854.0/1222.4
1483.2/ 977.9
2244.4/1480.2
1848.6/1848.6
1478.9/1478.9
2237.8/2237.8
1848.6/1848.6
1478.9/1478.9
2237.8/2237.8
1843.2/1430.9
1474.6/1138.7
2231.3/1723.6
1843.2/2003.2
1474.6/1597.9
2231.3/2418.2
1843.2/2051.7
1474.6/1635.3
2231.3/2474.7
Rec
Fuse
Size
450/250
500/300
225/125
175/100
300/150
600/300
600/350
300/150
200/125
300/175
450/450
500/500
225/225
175/175
300/300
600/600
600/600
300/300
200/200
300/300
700/600
700/600
350/300
250/200
400/300
700/600
700/700
350/300
250/250
400/350
450/300
350/200
500/300
450/350
350/250
500/400
500/300
400/250
600/350
450/450
350/350
500/500
500/450
400/350
600/500
450/600
350/400
500/600
500/700
400/500
600/800
500/700
400/600
600/800
LEGEND
Wye-Delta
Across-the-Line
MCA
383.8/227.9
422.6/251.0
191.9/113.9
147.7/ 87.8
223.9/133.7
434.8/265.1
478.1/291.6
216.9/132.1
167.0/102.3
253.3/155.1
5 HP PUMP, 3450 RPM

ICF
MOCP
WD
XL
600/350
700/350
300/175
225/125
350/200
700/400
800/450
350/200
250/150
400/250
660.8/407.2
756.7/465.5
330.4/203.6
962.4/574.6
263.9/162.7
769.9/459.7
400.2/246.8 1165.2/695.8
828.8/407.2
950.7/465.5
414.4/203.6 1222.4/574.6
331.9/162.7
977.9/459.7
501.2/246.8 1480.2/695.8
Rec
Fuse
Size
450/300
500/300
225/150
175/110
300/175
600/350
600/350
300/175
200/125
300/200
CONTROL CIRCUIT
Voltage
MCA
1 PH,
and
60 Hz
MOCP
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
50
115
50
115
50
115
50
115
50
115
50
115
50
115
50
115
50

to 500 kcmil.
3/0 to 500 kcmil.
NOTES:
63
Table 8 30XA140-500 Electrical Data, Dual Point (High Ambient Option) (cont)
UNIT
30XA
140
160
180
200
220
240
260
280
300
325
350
400
450
500
ICF
MCA
MOCP
WD
XL
UNIT VOLTAGE
Supplied
V-Hz
(3 Ph)
NUMBER
OF
COND
Min Max
REQD
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
460-60
575-60
380-60
460-60
575-60
380-60
460-60
575-60
380-60
460-60
575-60
380-60
460-60
575-60
380-60
460-60
575-60
380-60
460-60
575-60
380-60
460-60
575-60
380-60
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
414
518
342
414
518
342
414
518
342
414
518
342
414
518
342
414
518
342
414
518
342
414
518
342
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
506
633
418
506
633
418
506
633
418
506
633
418
506
633
418
506
633
418
506
633
418
506
633
418
6/4
6/4
6/4
6/4
6/4
6/4
6/4
6/4
6/4
6/4
6/6
6/6
6/6
6/6
6/6
6/6
6/6
6/6
6/6
6/6
7/6
7/6
7/6
7/6
7/6
7/6
7/6
7/6
7/6
7/6
9/6
9/6
9/6
9/7
9/7
9/7
10/6
10/6
10/6
9/9
9/9
9/9
9/9
9/9
9/9
8/12
8/12
8/12
8/14
8/14
8/14
8/14
8/14
8/14
MCA
383.8/235.1
422.6/259.0
191.9/117.5
147.7/ 90.7
223.9/138.0
434.8/272.3
478.1/299.6
216.9/135.7
167.0/105.2
253.3/159.5

ICF
MOCP
WD
XL
600/350
700/400
300/175
225/125
350/200
700/400
800/450
350/200
250/150
400/250
660.8/414.4
756.7/473.4
330.4/207.2
263.9/165.6
400.2/251.2
828.8/414.4
950.7/473.4
414.4/207.2
331.9/165.6
501.2/251.2
Rec
Fuse
Size
450/300
500/300
962.4/578.2 225/150
769.9 /462.6 175/110
1165.2/700.2 300/175
600/350
600/350
1222.4/578.2 300/175
977.9/462.6 200/125
1480.2/700.2 300/200
LEGEND
Wye-Delta
Across-the-Line
MCA
383.8/242.3
422.6/266.9
191.9/121.1
147.7/ 93.5
223.9/142.4
434.8/279.5
478.1/307.6
216.9/139.3
167.0/108.1
253.3/163.8

ICF
MOCP
WD
XL
600/350
700/400
300/175
225/125
350/200
700/400
800/450
350/200
250/150
400/250
660.8/421.6
756.7/481.4
330.4/210.8
263.9/168.4
400.2/255.5
828.8/421.6
950.7/481.4
414.4/210.8
331.9/168.4
501.2/255.5
962.4/581.8
769.9/465.4
1165.2/704.5
1222.4/581.8
977.9/465.4
1480.2/704.5
Rec
Fuse
Size
450/300
500/350
225/150
175/110
300/175
600/350
600/400
300/175
200/125
300/200
CONTROL CIRCUIT
Voltage
MCA
1 PH,
and
60 Hz
MOCP
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
50
115
50
115
50
115
50
115
50
115
50
115
50
115
50
115
50

to 500 kcmil.
3/0 to 500 kcmil.
NOTES:
64
Table 8 30XA140-500 Electrical Data, Dual Point (High Ambient Option) (cont)
UNIT
30XA
140
160
180
200
220
240
260
280
300
325
350
400
450
500
ICF
MCA
MOCP
WD
XL
UNIT VOLTAGE
Supplied
V-Hz
(3 Ph)
Min
Max
NUMBER
OF
COND
REQD
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
230-60
200-60
460-60
575-60
380-60
460-60
575-60
380-60
460-60
575-60
380-60
460-60
575-60
380-60
460-60
575-60
380-60
460-60
575-60
380-60
460-60
575-60
380-60
460-60
575-60
380-60
460-60
575-60
380-60
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
207
187
414
518
342
414
518
342
414
518
342
414
518
342
414
518
342
414
518
342
414
518
342
414
518
342
414
518
342
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
253
220
506
633
418
506
633
418
506
633
418
506
633
418
506
633
418
506
633
418
506
633
418
506
633
418
506
633
418
6/4
6/4
6/4
6/4
6/4
6/4
6/4
6/4
6/4
6/4
6/6
6/6
6/6
6/6
6/6
6/6
6/6
6/6
6/6
6/6
7/6
7/6
7/6
7/6
7/6
7/6
7/6
7/6
7/6
7/6
9/6
9/6
9/6
9/7
9/7
9/7
10/6
10/6
10/6
9/9
9/9
9/9
9/9
9/9
9/9
8/12
8/12
8/12
8/14
8/14
8/14
8/14
8/14
8/14

ICF
MCA
MOCP
383.8/256.9
422.6/283.1
191.9/128.4
147.7/ 99.4
223.9/151.2
434.8/294.1
478.1/323.7
216.9/146.6
167.0/113.9
253.3/172.7
600/350
700/400
300/175
225/150
350/225
700/450
800/500
350/225
250/175
400/250
LEGEND
Wye-Delta
Across-the-Line
WD
XL
660.8/436.2
756.7/497.5
330.4/218.1
263.9/174.3
400.2/264.4
828.8/436.2
950.7/497.5
414.4/218.1
331.9/174.3
501.2/264.4
962.4/589.1
769.9/471.3
1165.2/713.4
1222.4/589.1
977.9/471.3
1480.2/713.4
Rec
Fuse
Size
450/300
500/350
225/150
175/125
300/175
600/350
600/400
300/175
200/150
300/200
CONTROL CIRCUIT
Voltage
MCA
1 PH,
and
60 Hz
MOCP
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
40
115
50
115
50
115
50
115
50
115
50
115
50
115
50
115
50
115
50

to 500 kcmil.
3/0 to 500 kcmil.
NOTES:
65
Table 9 Power and Control Connections

30XA
080
090
100
110
120
140
160
180
200
220
240
260
280
300
325
350
400
450
500
VOLTAGE
3 PH
60 Hz
200
230
380
460
575
200
230
380
460
575
200
230
380
460
575
200
230
380
460
575
200
230
380
460
575
COMBI*
Power
Circuit 1 (& 2)**
Circuit 1 (& 2)
Circuit 1 (& 2)
Circuit 1 (& 2)
Circuit 1 (& 2)
Circuit 1 (& 2)
Circuit 1 (& 2)
Control
Yes
Yes
Yes
Yes
Yes
No
No
POWER AND CONTROL CONNECTIONS

PEB1
Power
Control
Circuit 1 (& 2)
Circuit 1 (& 2)
Circuit 1 (& 2)
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Circuit 1 (& 2)
Circuit 1 (& 2)
Circuit 1 (& 2)
Yes
Yes
Yes
Circuit 1
Circuit 1
Circuit 1
No
No
No
Circuit 1 (& 2)
Circuit 1 (& 2)
Circuit 1 (& 2)
PEB2
Power
Control
Circuit 1 (& 2)
Circuit 1 (& 2)
No
No
Circuit 2
Circuit 2
Circuit 2
Yes
Yes
Yes
*COMBI box is located at the end of the unit.

PEB1 and PEB2 boxes are located on the side of the unit. If both boxes are used, the one on the left (viewing from the front of the boxes) is PEB1.
**For dual incoming power.
Shaded area means that box is not used on this model.
NOTE: Shaded portions of Table indicate that the power and control connection is not available.
66
Table 10 Compressor and Fan Electrical Data

UNIT
30XA VOLTAGE NUMBER
UNIT
V-Hz
OF COND
SIZE
(3 Ph,
FANS*
60 Hz)
CONDENSER
FANS
COMPRESSOR
B
LRA (All Units)
RLA
A
LRA (All Units)
FLA
High
Ambient
Standard
XL
Temp
Cond. Fans
Cond. Fans (850 rpm)
(1140 rpm)
200
3/3
11.9
6.6
1081.0
230
3/3
10.8
6.0
940.0
080
380
3/3
6.5
3.6
569.0
460
3/3
5.5
3.0
470.0
575
3/3
4.3
2.4
376.0
200
4/4
11.9
6.6
1081.0
230
4/4
10.8
6.0
940.0
090
380
4/4
6.5
3.6
569.0
460
4/4
5.5
3.0
470.0
575
4/4
4.3
2.4
376.0
200
4/4
11.9
6.6
1357.0
230
4/4
10.8
6.0
1180.0
100
380
4/4
6.5
3.6
714.0
460
4/4
5.5
3.0
590.0
575
4/4
4.3
2.4
472.0
200
4/4
11.9
6.6
1357.0
230
4/4
10.8
6.0
1180.0
110
380
4/4
6.5
3.6
714.0
460
4/4
5.5
3.0
590.0
575
4/4
4.3
2.4
472.0
200
4/4
11.9
6.6
1357.0
230
4/4
10.8
6.0
1180.0
120
380
4/4
6.5
3.6
714.0
460
4/4
5.5
3.0
590.0
575
4/4
4.3
2.4
472.0
200
6/4
11.9
6.6
2162.0
230
6/4
10.8
6.0
1880.0
140
380
6/4
6.5
3.6
1138.0
460
6/4
5.5
3.0
940.0
575
6/4
4.3
2.4
752.0
200
6/4
11.9
6.6
2714.0
230
6/4
10.8
6.0
2360.0
160
380
6/4
6.5
3.6
1428.0
460
6/4
5.5
3.0
1180.0
575
6/4
4.3
2.4
944.0
200
6/6
11.9
6.6
2162.0
230
6/6
10.8
6.0
1880.0
180
380
6/6
6.5
3.6
1138.0
460
6/6
5.5
3.0
940.0
575
6/6
4.3
2.4
752.0
200
6/6
11.9
6.6
2714.0
230
6/6
10.8
6.0
2360.0
200
380
6/6
6.5
3.6
1428.0
460
6/6
5.5
3.0
1180.0
575
6/6
4.3
2.4
944.0
200
7/6
11.9
6.6
2714.0
230
7/6
10.8
6.0
2360.0
220
380
7/6
6.5
3.6
1428.0
460
7/6
5.5
3.0
1180.0
575
7/6
4.3
2.4
944.0
200
7/6
11.9
6.6
2714.0
230
7/6
10.8
6.0
2360.0
240
380
7/6
6.5
3.6
1428.0
460
7/6
5.5
3.0
1180.0
575
7/6
4.3
2.4
944.0
380
9/6
6.5
3.6
2143.0
260
460
9/6
5.5
3.0
1770.0
575
9/6
4.3
2.4
1416.0
380
9/7
6.5
3.6
2143.0
280
460
9/7
5.5
3.0
1770.0
575
9/7
4.3
2.4
1416.0
380
9/7
6.5
3.6
2143.0
300
460
9/7
5.5
3.0
1770.0
575
9/7
4.3
2.4
1416.0
380
9/9
6.5
3.6
2143.0
325
460
9/9
5.5
3.0
1770.0
575
9/9
4.3
2.4
1416.0
380
9/9
6.5
3.6
2143.0
350
460
9/9
5.5
3.0
1770.0
575
9/9
4.3
2.4
1416.0
380
8/12
6.5
3.6
1428.0
400
460
8/12
5.5
3.0
1180.0
575
8/12
4.3
2.4
944.0
380
8/14
6.5
3.6
1138.0
450
460
8/14
5.5
3.0
940.0
575
8/14
4.3
2.4
752.0
380
8/14
6.5
3.6
1428.0
500
460
8/14
5.5
3.0
1180.0
575
8/14
4.3
2.4
944.0
LEGEND
LRA Locked Rotor Amps
WD Wye Delta
RLA Rated Load Amps
XL Across-the-Line
WD
345.0
300.0
182.0
150.0
120.0
345.0
300.0
182.0
150.0
120.0
437.0
380.0
230.0
190.0
152.0
437.0
380.0
230.0
190.0
152.0
437.0
380.0
230.0
190.0
152.0
690.0
600.0
363.0
300.0
240.0
863.0
750.0
454.0
375.0
300.0
690.0
600.0
363.0
300.0
240.0
863.0
750.0
454.0
375.0
300.0
863.0
750.0
454.0
375.0
300.0
863.0
750.0
454.0
375.0
300.0
684.0
565.0
452.0
684.0
565.0
452.0
684.0
565.0
452.0
684.0
565.0
452.0
684.0
565.0
452.0
454.0
375.0
300.0
363.0
300.0
240.0
454.0
375.0
300.0
RLA
High
Ambient
Standard
Temp
Cond. Fans
(1140 rpm)
130.9
118.9
68.8
59.4
45.4
134.3
122.0
70.6
61.0
46.6
148.4
134.9
78.3
67.5
51.3
180.9
164.7
95.4
82.0
62.9
180.9
164.7
95.4
82.0
62.9
280.8
255.2
147.7
127.6
97.5
325.2
296.0
171.3
147.6
112.9
280.8
255.2
147.7
127.6
97.5
325.2
296.0
171.3
147.6
112.9
387.3
352.3
204.2
176.1
134.8
387.3
352.3
204.2
176.1
134.8
277.9
240.4
183.7
277.9
240.4
183.7
330.8
285.6
218.2
277.9
240.4
183.7
330.8
285.6
218.2
204.2
176.1
134.8
147.7
127.6
97.5
204.2
176.1
134.8
136.8
124.2
71.9
62.1
47.5
140.0
127.1
73.5
63.6
48.6
154.8
140.7
81.6
70.4
53.5
190.7
173.6
100.6
86.4
66.3
190.7
173.6
100.6
86.4
66.3
293.9
267.2
154.6
133.6
102.0
340.6
310.0
179.4
154.6
118.2
293.9
267.2
154.6
133.6
102.0
340.6
310.0
179.4
154.6
118.2
406.6
369.8
214.3
184.9
141.5
406.6
369.8
214.3
184.9
141.5
293.0
253.5
193.7
293.0
253.5
193.7
350.3
302.4
231.0
293.0
253.5
193.7
350.3
302.4
231.0
214.3
184.9
141.5
154.6
133.6
102.0
214.3
184.9
141.5
*Quantity of fan motors for incoming power supply Circuit 1/Circuit 2.
67
XL
WD
High
Ambient
Standard
Temp
Cond. Fans
(1140 rpm)
C
LRA (All Units)
XL
WD
RLA
High
Ambient
Standard
Temp
Cond. Fans
(1140 rpm)
1081.0 345.0
130.9
136.8
940.0 300.0
118.9
124.2
569.0 182.0
68.8
71.9
470.0 150.0
59.4
62.1
376.0 120.0
45.4
47.5
1081.0 345.0
134.3
140.0
940.0 300.0
122.0
127.1
569.0 182.0
70.6
73.5
470.0 150.0
61.0
63.6
376.0 120.0
46.6
48.6
1357.0 437.0
148.4
154.8
1180.0 380.0
134.9
140.7
714.0 230.0
78.3
81.6
590.0 190.0
67.5
70.4
472.0 152.0
51.3
53.5
1357.0 437.0
148.4
154.8
1180.0 380.0
134.9
140.7
714.0 230.0
78.3
81.6
590.0 190.0
67.5
70.4
472.0 152.0
51.3
53.5
1357.0 437.0
180.9
190.7
1180.0 380.0
164.7
173.6
714.0 230.0
95.4
100.6
590.0 190.0
82.0
86.4
472.0 152.0
62.9
66.3
1357.0 437.0
148.4
154.8
1180.0 380.0
134.9
140.7
714.0 230.0
78.3
81.6
590.0 190.0
67.5
70.4
472.0 152.0
51.3
53.5
1357.0 437.0
180.9
190.7
1180.0 380.0
164.7
173.6
714.0 230.0
95.4
100.6
590.0 190.0
82.0
86.4
472.0 152.0
62.9
66.3
2162.0 690.0
280.8
293.9
1880.0 600.0
255.2
267.2
1138.0 363.0
147.7
154.6
940.0 300.0
127.6
133.6
752.0 240.0
97.5
102.0
2714.0 863.0
325.2
340.6
2360.0 750.0
296.0
310.0
1428.0 454.0
171.3
179.4
1180.0 375.0
147.6
154.6
944.0 300.0
112.9
118.2
2714.0 863.0
325.2
340.6
2360.0 750.0
296.0
310.0
1428.0 454.0
171.3
179.4
1180.0 375.0
147.6
154.6
944.0 300.0
112.9
118.2
2714.0 863.0
387.3
406.6
2360.0 750.0
352.3
369.8
1428.0 454.0
204.2
214.3
1180.0 375.0
176.1
184.9
944.0 300.0
134.8
141.5
1428.0 454.0
171.3
179.4
1180.0 375.0
147.6
154.6
944.0 300.0
112.9
118.2
1428.0 454.0
204.2
214.3
1180.0 375.0
176.1
184.9
944.0 300.0
134.8
141.5
1428.0 454.0
204.2
214.3
1180.0 375.0
176.1
184.9
944.0 300.0
134.8
141.5
2143.0 684.0
277.9
293.0
1770.0 565.0
240.4
253.5
1416.0 452.0
183.7
193.7
2143.0 684.0
277.9
293.0
1770.0 565.0
240.4
253.5
1416.0 452.0
183.7
193.7
1428.0 454.0
204.2
214.3
293.0 2143.0
277.9
293.0
1180.0 375.0
176.1
184.9
253.5 1770.0
240.4
253.5
944.0 300.0
134.8
141.5
193.7 1416.0
183.7
193.7
2143.0 684.0
330.8
350.3
2143.0 684.0
330.8
350.3
1770.0 565.0
285.6
302.4
1770.0 565.0
285.6
302.4
1416.0 452.0
218.2
231.0
1416.0 452.0
218.2
231.0
2143.0 684.0
330.8
350.3
2143.0 684.0
330.8
350.3
1770.0 565.0
285.6
302.4
1770.0 565.0
285.6
302.4
1416.0 452.0
218.2
231.0
1416.0 452.0
218.2
231.0
NOTES:
1. For 30XA080-350 units with dual power supply, main power supply 1 uses refrigerant
circuit A components to calculate MCA and MOCP. Main power supply 2 uses refrigerant circuit B components to calculate MCA and MOCP.
2. 30XA400-500 units have dual power supply. Main power supply 1 uses refrigerant circuit C components to calculate MCA and MOCP. Main power supply 2 uses refrigerant
circuit A and B components to calculate MCA and MOCP.
Table 11 Pump Electrical Data

PUMP
HP
5
7.5
10
15
UNIT VOLTAGE
V-Hz (3 Ph)
230-60
208-60
460-60
575-60
380-60
230-60
208-60
460-60
575-60
380-60
230-60
208-60
460-60
575-60
380-60
230-60
208-60
460-60
575-60
380-60
HYDRONIC SYSTEM (SINGLE OR DUAL)

FLA (Each)
11.6
12.6
5.8
4.6
7.0
17.4
18.5
8.7
7.0
10.4
23.0
25.0
11.5
9.2
14.0
34.0
36.7
17.0
14.0
21.0
30XA
UNIT SIZE
090-160
090-160
090-160
090-160
FLA Full Load Amps
2. Cut the CCN wire and strip the ends of the red (+), white
(ground), and black () conductors. Substitute appropriate colors for different colored cables.
3. Connect the red wire to (+) terminal on TB3 of the plug,
the white wire to COM terminal, and the black wire to the
() terminal.
4. The RJ14 CCN connector on TB3 can also be used, but is
only intended for temporary connection (for example, a
laptop computer running service tool).
CARRIER COMFORT NETWORK COMMUNICATION

BUS WIRING (See Fig. 34) The communication bus wiring
is a shielded, 3-conductor cable with drain wire and is field
supplied and installed in the field.
The system elements are connected to the communication
bus in a daisy chain arrangement. The positive pin of each
system element communication connector must be wired to the
positive pins of the system elements on either side of it. This is
also required for the negative and signal ground pins of
each system element. Wiring connections for CCN (Carrier
Comfort Network) should be made at TB (terminal block) 3.
Consult the CCN Contractors Manual for further information.
See Fig. 34.
NOTE: Conductors and drain wire must be 20 AWG
(American Wire Gage) minimum stranded, tinned copper.
Individual conductors must be insulated with PVC, PVC/
nylon, vinyl, Teflon, or polyethylene. An aluminum/polyester
100% foil shield and an outer jacket of PVC, PVC/nylon,
chrome vinyl, or Teflon with a minimum operating temperature range of 4 F (20 C) to 140 F (60 C) is required. See
Table 12 for a list of manufacturers that produce CCN bus
wiring that meet these requirements.
IMPORTANT: A shorted CCN bus cable will prevent

some routines from running and may prevent the unit
from starting. If abnormal conditions occur, disconnect
the machine from the CCN. If conditions return to
normal, check the CCN connector and cable. Run new
cable if necessary. A short in one section of the bus
can cause problems with all system elements on the
bus.
NON-CCN COMMUNICATION WIRING The 30XA units
offer several non-CCN translators. Refer to the separate installation instructions for additional wiring steps.
FIELD CONTROL OPTION WIRING Install field control
wiring options. Some options, such as 4 to 20 mA demand
limit that requires the Energy Management Module, may
require that accessories be installed first (if not factory
installed) for terminal connections.
DUAL CHILLER LEAVING WATER SENSOR If the dual
chiller algorithm is used and the machines are installed in parallel, an additional chilled water sensor must be installed for
each chiller. Install the wells in the common leaving water
header. See Fig 35. DO NOT relocate the chillers leaving
water thermistors. They must remain in place for the unit to
operate properly.
The thermistor well is a 1/4 in. NPT fitting for securing the
well in the piping. The piping must be drilled and tapped for
the well. Select a location that will allow for removal of the
thermistor without any restrictions.
Once the well is inserted, install the thermistors. Insert the
thermistor into the well until the o-ring reaches the well body.
Use the nut on the thermistor to secure the thermistor in place.
Once the thermistor is in place, it is recommended that a
thermistor wire loop be made and secured with a wire tie to the
chilled water pipe. See Fig. 36.
For dual chiller control a CCN bus must be connected
between the two modules. See the Carrier Comfort Network
Communication Bus Wiring section for additional information.
Table 12 CCN Communication Bus Wiring

MANUFACTURER
Alpha
American
Belden
Columbia
Manhatten
Quabik
PART NUMBER
Regular Wiring
Plenum Wiring
1895
A21451
A48301
8205
884421
D6451
M13402
M64430
6130
It is important when connecting to a CCN communication

bus that a color coding scheme be used for the entire network
to simplify the installation. It is recommended that red be used
for the signal positive, black for the signal negative, and white
for the signal ground. Use a similar scheme for cables containing different colored wires. At each system element, the shields
of its communication bus cables must be tied together. If the
communication bus is entirely within one building, the resulting continuous shield must be connected to a ground at one
point only. If the communication bus cable exits from one
building and enters another, the shields must be connected to
grounds at the lightning suppressor in each building where the
cable enters or exits the building (one point per building only).
To connect the unit to the network:
1. Turn off power to the control box.
68
(+) (COM) (-) SHIELD
BLK
CCN
CCN
RED
LEN
WHT
CCN
CCN
SHIELD
BLK
LEN
RED
RED
BLK
CCN
CCN
WHT
LEN
WHT
TO NEXT
DEVICE
a30-4001
CCN
LEN
LEGEND
Carrier Comfort Network
Local Equipment Network
Fig. 34 TB3 CCN Wiring
5/8 in. HEX
1/4-18 NPT
6" MINIMUM
CLEARANCE FOR
THERMISTOR
REMOVAL
1.188 in.
2.315 in.
a30-3999
Fig. 35 Dual Leaving Water Thermistor Well (Part No. OOPPG000008000A)

requires field-supplied dry contacts), remote lockout switch
and ice done switch (requires field-supplied dry contacts).
REMOTE ENHANCED DISPLAY (OR TOUCH PILOT
DISPLAY) For applications where remote monitoring of
the equipment is required; the remote enhanced display (or
Touch Pilot display) provides an indoor display, capable of
monitoring any equipment on the Carrier Comfort Network
(CCN) bus. A CCN bus is required.
LOW AMBIENT TEMPERATURE OPERATION If outdoor ambient operating temperatures below 32 F (0 C) are
expected, refer to separate installation instructions for lowambient operation using the low ambient temperature head
pressure control accessory.
MINIMUM LOAD ACCESSORY Contact a local Carrier
representative for more details if a minimum load accessory is
required for a specific application. For installation details, refer
to separate installation instructions supplied with the accessory
package.
UNIT SECURITY/PROTECTION ACCESSORIES For
applications with unique security and/or protection requirements, several options are available for unit protection.
Security grilles and hail guards are available. Contact a local
Carrier representative for more details. For installation details,
refer to separate installation instructions supplied with the
accessory package.
COMMUNICATION ACCESSORIES A number of communication options are available to meet any requirement.
Contact a local Carrier representative for more details. For
installation details, refer to separate installation instructions
supplied with the accessory package.
SERVICE OPTIONS Two accessories are available to aid
in servicing 30XA units: a ground fault convenience outlet
(GFI-CO) and a remote service port.
The GFI-CO is a convenience outlet with a 4-amp GFI
receptacle.
The remote service port is housed in a weather-proof enclosure with a communication port to plug in the Navigator
device.
INSERT THERMISTOR UNTIL

O-RING MEETS THE
THERMISTOR WELL BODY.
WIRE TIE
LOOP
THERMISTOR WIRE
AND SECURE
TO CHILLED WATER PIPE
a30-4000
Fig. 36 Dual Leaving Water Thermistor

(Part No. OOPPG000008105A)
Step 6 Install Accessories A number of acces-
sories are available to provide the following optional features

(for details, refer to the Controls and Troubleshooting guide
shipped with the unit).
ENERGY MANAGEMENT MODULE The Energy Management Module is used for any of the following types of
temperature reset, demand limit and ice features:
4 to 20 mA inputs for cooling set point reset and capacity
limit (requires field-supplied 4 to 20 mA generator)
0 to 10 v output for percentage total capacity running
24 v discrete outputs for shutdown and running relays
10k space temperature input
Discrete inputs for occupancy override, demand limit
switch 2 (step 1 demand limit is wired to the base board,
69
Contact your local Carrier representative for more details.

For installation details, refer to separate installation instructions
supplied with each accessory package.
CONTROL TRANSFORMER The control transformer
accessory eliminates the need for a separate power supply.
REFRIGERANT CHARGE
Step 7 Leak Test Unit The 30XA units are

shipped with a complete operating charge of R-134a (see
Tables 1A and 1B) and should be under sufficient pressure to
conduct a leak test.
The liquid charging method is recommended for complete

charging or when additional charge is required.
IMPORTANT: These units are designed for use with

R-134a only. DO NOT USE ANY OTHER refrigerant in these units.
When charging, circulate water through the cooler at all

times to prevent freezing. Freezing damage is considered
abuse and may void the Carrier warranty.
Perform a leak test to ensure that leaks have not developed

during unit shipment. Dehydration of the system is not required
unless the entire refrigerant charge has been lost. There are
several O-ring face seal fittings utilized in the oil line piping. If
a leak is detected at any of these fittings, open the system and
inspect the O-ring surface for foreign matter or damage. Do not
reuse O-rings. Repair any leak found following good refrigeration practice.
DO NOT OVERTIGHTEN THESE FITTINGS. Overtightening will result in O-ring damage.
IMPORTANT: These units are designed for use with

R-134a only. DO NOT USE ANY OTHER refrigerant in
these units.
DO NOT OVERCHARGE system. Overcharging results in

higher discharge pressure with higher cooling fluid consumption, possible compressor damage, and higher power
consumption.
The 30XA units are shipped from the factory with a full
charge of R-134a. The unit should not need to be charged at
installation unless a leak was detected in Step 6 Leak Test
Unit section. If dehydration and recharging is necessary, use
industry standard practices or refer to Carrier Standard Service
Techniques Manual as required.
Step 8 Refrigerant Charging

DEHYDRATION Refer to Carrier Standard Service Techniques Manual, Chapter 1, Refrigerants, Sections 6 and 7 for
details. Do not use compressor to evacuate system.
Copyright 2006 Carrier Corporation

Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.
Catalog No. 04-53300008-01
Printed in U.S.A.
Form 30XA-5SI
Pg 70
9-06
Replaces: 30XA-1SI
Book 2
Tab 5c

Chiller Carrier

Uploaded by

Copyright:

Available Formats

Chiller Carrier

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Chiller Carrier

Uploaded by

Copyright:

Available Formats

AQUAFORCE

Installing, starting up, and servicing this equipment can be

Electrical shock can cause personal injury and death. Shut

can be reduced to 3 ft (1 m) without sacrificing performance as

age upon arrival. If damage is found, immediately file a claim

Step 2 Place, Mount, and Rig the Unit

When considering a location for the unit, be sure to consult

30XA Air-Cooled AquaForce Chiller

Condenser Coil/Low Sound Options

Hydronic Pump Package Options

Refrigeration Circuit Options

Fig. 1 AquaForce Chiller Model Number Designation

1.50 DIA. [38.1]

Control Box All Voltages

Fig. 2 30XA080 Air-Cooled Liquid Chiller Dimensions

7/8" knockouts for main power entry

3/4 NPT Relief

5" Victaulic Entering Water

5" Victaulic Leaving Water

Fig. 2 30XA080 Air-Cooled Liquid Chiller Dimensions (cont)

Control Box All Voltages

LEFT END VIEW

7/8" knockouts for main power entry

RIGHT END VIEW

1.50 DIA. [38.1]

0.875 DIA. [22.2]

Control Box All Voltages

7/8" knockouts for main power entry

Fig. 3 30XA090-120 Air-Cooled Liquid Chiller Dimensions

5" Victaulic Entering Water

3/4 NPT Relief Conn. Female

5" Victaulic Entering Water

5" Victaulic Leaving Water

Fig. 3 30XA090-120 Air-Cooled Liquid Chiller Dimensions (cont)

5" Victaulic Leaving Water

Control Box All Voltages

LEFT END VIEW

7/8" knockouts for main power entry

5" Victaulic Leaving Water

5" Victaulic Entering Water

RIGHT END VIEW

7/8" knockouts for main power entry

Control Box, incoming

Fig. 4 30XA140,160 Air-Cooled Liquid Chiller Dimensions

RIGHT END VIEW

Control power entry (all voltages)

7/8" knockouts for

1.50 DIA. [38.1]

0.875 DIA. [22.2]

5" Victaulic Leaving Water

Fig. 4 30XA140,160 Air-Cooled Liquid Chiller Dimensions (cont)

LEFT END VIEW

3/4 NPT Relief Conn. Female

5" Victaulic Entering Water

RIGHT END VIEW

Fig. 5 30XA180,200 Air-Cooled Liquid Chiller Dimensions

7/8" knockouts for main power entry 380, 460, 575v

Control Box, incoming

Control power entry

LEFT END VIEW