Le03 Pi FR Fa20

Process Instrumentation
CHE426
Dr. Fahad Rehman
Department of Chemical Engineering
CUI, Lahore Campus
CLOs covered in this lecture
• CLO1: Describe the fundamentals of Process Instrumentation
• Contents
• We will talk about some fundamentals definitions used in measurements,
data types, sampling method and Transducers
Some fundamental definitions
• Accuracy
The quality or state of being correct
Or
The degree to which the result of a measurement, calculation, or
specification conforms to the correct value or a standard.
• It depends on linearity, hysteresis, offset, and sensitivity. The resulting

discrepancy is stated as a plus-or-minus deviation from true reading, and
is normally specified as a percentage of reading, span, or of full-scale
reading or deflection (% FSD), and can be expressed as an absolute value.
Accuracy
• A pressure sensor has a span of 25 to 150 psi. Specify the error when
measuring 107 psi, if the accuracy of the gauge is (a) ±1.5% of span,
(b)±2% FSD, and (c) ±1.3% of reading.
• a. Error =±0.015 (150 −25) psi=±1.88 psi.
• b. Error =±0.02 × 150 psi=±3 psi.
• c. Error =±0.013 × 107 psi=±1.391 psi.
• Sometimes accuracy vaires with the reading !!!

Some fundamental definitions
• Precision
The quality or state of being Precise: Exactness
or
The degree of refinement with which an operation is performed or a
measurement stated
Accuracy vs Precision
Data types and Sampling
• Variables, hence the data, are analog in nature.
• Before the digital processing evolved, sensor signals were processed
using analog circuits and techniques which still exists. However, most
modern systems now use digital techniques for signal processing.
• An analog signal is a continuous signal that represents physical
measurements such as reading on pressure gauge or speed meter on
a motor bike.
• Digital signals are time separated signals which are generated using
digital modulation. It uses a continuous range of values that help you
to represent information. Digital signal uses discrete 0 and 1 to
represent information.
Analoge vs Digital
• Pneumatic Data
• Pneumatic Signal is pressure of a gas (or air) in a pipe, instead of electrical
current.
• Pressure is used for data transmission before the use of electrical signals.
• Used in conditions where high electrical noise could affect electrical signals
• Or hazardous conditions where an electrical spark could cause an explosion
or fire hazard.
• The most common range for pneumatic data transmission is 3 to 15 psi (20
to100 kPa in SI units), where 0 psi is a fault condition.
• Pneumatic Data
• It is difficult to control very low pressures accurately with a simple
regulator
• Provide vacuum to allow for calibration and measurement hysteresis
& repeatability errors
Sampling
• Discrete Sampling/measurement
• Carried out at a fixed time interval
• When the requirements are flexible or not a safety risk
• Continuous sampling measurement

• When the measured variable is absolutely crucial for product quality
or plant safety
• The data is usually transferred continuously electrically to the control
room
Calibration
• How would know you instruments/sensor are providing the accurate
reading?
• How would you determine the temperature shown by thermocouple is

accurate or your pressure differential cell is indicating the right pressure.
• You calibrate them with standard devices such as Thermometer
• Such as DO probe or TDS probe…….

Transducers
• Transducer is defined as a device, which converts physical quantity
such as pressure or temperature to into electrical signal.
• These are widely used and essential in measurements because not all
quantities that need to be measured can be displayed as easily as
others.
Continued….
• For example, How does a
thermocouple work ?
• Does it really measure
Temperature?
• Mercury thermometer converts variations in
temperature into variations in the length of a
column of mercury.
• Since the variation in the length of the mercury
column is rather simple to measure, the mercury
thermometer becomes a convenient device for
measuring temperature.
Continued….
• On the other hand, the actual temperature variation is not as easy to
display directly.
• Another example is manometer, which detects pressure and indicates
it directly on a scale calibrated in actual units of pressure.
Let’s take a slight detour!!!

Continued….
• How do we know the temperature
and or a pressure of a system in the
first place? When no transducer or
instrument was invented???
• The answer is we Don’t!!!
• We only know the reference points
such as melting point and boiling
point. And we have divided these
points in several different intervals.
• I would like to know how do we
make reference points for pressure
??? Lets discuss in our online
interactive session.
Continued….
• Moral: Thus the transducer is a device, which provides a usable
output in response to specific input measured, which may be physical
or mechanical quantity, property or condition.
• The transducer may be mechanical, electrical, magnetic, optical,

chemical, acoustic, thermal nuclear, or a combination of any two or
more of these.
Next Lecture
• We will continue with Transducers, their classification, working,
characteristics and selection criteria and Assignment 1.

Le03 Pi FR Fa20

Uploaded by

Copyright:

Available Formats

Le03 Pi FR Fa20

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Le03 Pi FR Fa20

Uploaded by

Copyright:

Available Formats

Process Instrumentation

• It depends on linearity, hysteresis, offset, and sensitivity. The resulting

• Sometimes accuracy vaires with the reading !!!

• Continuous sampling measurement

• How would you determine the temperature shown by thermocouple is

• You calibrate them with standard devices such as Thermometer

• Such as DO probe or TDS probe…….

Let’s take a slight detour!!!

• The transducer may be mechanical, electrical, magnetic, optical,

You might also like