Sa5150 750adv

Axis AX UL Multicriteria Detector
The Axis AX UL Multicriteria Detector (Smoke/Heat) is our most

advanced detector offering suitable for a wide range of
applications. It uses Purelight® high-tech smoke sensing
technology to detect smoke particles entering the
chamber and is fitted with two thermistors for detecting heat. It
can be switched to detect smoke, heat or a combination of both,
offering greater flexibility, fast detection and advanced false
alarm management.
Operation
The low profile design of the Axis AX UL Multicriteria Detector

(Smoke/Heat) is sleek and evolutionary, with a 360º LED
indicator which illuminates red when in alarm.
At the heart of the smoke smoke sensor is Purelight®

Sensing Technology which incorporates:
Cone technology combined with a high-intensity infrared
LED to provide stability and accurate sensitivity to
smoke. Features
A sophisticated dynamic algorithm, providing transient
rejection and compensation for drift whilst maintaining Built-in isolator
accurate sensitivity.
Purelight® optical technology for enhanced smoke detection
Signals from the smoke smoke chamber and and false alarm management
temperature sensors are independent and represent the smoke Drift compensation
level and air temperature respectively in the vicinity of the
Backwards compatible with Discovery
detector; the detector's micro-controller processes both signals.
The temperature signal processing extracts only Base locking mechanism (grub screw)
rate-of-rise information for combination with the smoke signal.
In-built self test
The optical sensor will trigger an alarm at 1.2 %/ft and the heat XPERT card addressing
sensor at 69.8 ºF (21 ºC) rise. Minimum time to alarm is ten
seconds. Dual heat sensors
The detector will not respond to slow increases in temperature,

but a large, sudden change can cause an alarm without the
presence of smoke. Listings and Approvals
The sensor will respond to smoke or heat, or a combination of Approved to UL268 7th edition, UL 521, ULC S529, ULC
both. S530, FM 3210
System compatibility
Axis AX detectors have been designed to operate on Discovery

protocol loops. This allows for Axis AX detectors and bases to
operate on existing systems. Operating modes
Maintenance and service Axis AX multisensor detectors give the choice of five operating
modes which respond as follows:
Axis AX detectors have been designed with a comprehensive
set of features to support maintenance and service, from Modes 1, 3 and 4 - multicriteria response
self-test capabilities to drift compensation warnings on dirty
Mode 2 - optical response only
detectors.
Mode 5 - heat response only
Version [1.00] Page 1 of 2

www.advancedco.com
Specification
Digital communication protocol Discovery
Supply wiring Two wire supply, polarity sensitive
Sensitivity 1.2-2.1%/ft
Supply voltage (Vmin-Vmax) 17-28 Vdc
Sampling frequency Once per second
Modulation voltage 5-9V peak to peak
Supervisory current 500 μA
Switch-on surge current 1.0 mA
Alarm/operated current, LED on 4.0 mA
Status indicator
Alarm - Red
Fault - Flashing yellow
Isolate - Yellow
Poll - Flashing green
Additional remote LED current 5mA maximum

Product operating temperature 32° F to 131° F (0° C to 55° C)
Heat element rating (Mode 5 only) 115 ° F (47° C)
Effect of atmospheric pressure None
Air velocity 0-300 fpm
Humidity 0% to 95% RH (no condensation or icing)
IP rating IP44
Weight 2.93 ounces (83g)
Mzximum spacing (Mode 5 only) 50 ft (15.24m)
Dimensions
4" (100mm) diameter x 1.51" (38.5mm height)
1.98" (50.5 mm) height with XPERT8 Intelligent Mounting Base
Materials
Housing: White flame-retardant polycarbonate.
Terminals: Tin-plated stainless steel
All data is supplied subject to change without notice. Specifications are typical at 24 V, 73 ° F and 50% RH unless otherwise stated.
Isolated detector data
Maximum loop current (1c max; L1 in/out) 1A

Maximum series resistance (Z c max; L1 in/out) 100 mΩ
Order Codes and Options

SA5150-750ADV Axis AX UL Multicriteria Detector
SA5000-210ADV Axis AX UL Base - 4"
SA5000-230ADV Axis AX UL Base - 6"
Check if this document is up to date | Give us feedback
Advanced, The Bridges, Balliol Business Park, Newcastle upon Tyne, NE12 8EW, UK T: +44 (0)345 894 7000, E: enquiries@advancedco.com,
W: www.advancedco.com
As our policy is one of constant product improvement the right is therefore reserved to modify product specifications without prior notice.
Version [1.00] Page 2 of 2

Sa5150 750adv

Uploaded by

Copyright:

Available Formats

Sa5150 750adv

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Sa5150 750adv

Uploaded by

Copyright:

Available Formats

Axis AX UL Multicriteria Detector

The Axis AX UL Multicriteria Detector (Smoke/Heat) is our most

The low profile design of the Axis AX UL Multicriteria Detector

At the heart of the smoke smoke sensor is Purelight®

The detector will not respond to slow increases in temperature,

Axis AX detectors have been designed to operate on Discovery

Version [1.00] Page 1 of 2

Additional remote LED current 5mA maximum

Isolated detector data

Maximum loop current (1c max; L1 in/out) 1A

Order Codes and Options

Check if this document is up to date | Give us feedback

Version [1.00] Page 2 of 2

You might also like