FL Tool Catalog

Back to Catalog Index
Quick Change Tapered Toolholders

Quick-change tapered toolholders are designed and
built to increase product quality by accurately posi-
tioning cutting tools on production and non-pro-
duction machines. They feature improved cutting
tool centerline accuracy, positive drive ofthe cutting
tool and thru-coolant capability.
Each patented tapered toolholder also features a
compact design which minimizes spindle to spindle
center distance as well as overhang from the bear-
ing diameters to the spindle end, mak ing the system
ideal for single and mUltiple spindle stub drilling
applications without the use of costly bushing plates.
Six separate body sizes are available to accommo-
date a wide variety of tool shank diameters begin-
ning at V16-inch (1.5mm) diameter. Each tapered
tool holder assembly features a guaranteed accuracy
of 0.0005 T.I.R. runout 2-in. from the collet face
measured by a zero spindle and class XX gage pin.
Special holders, such as extended lengths and solid
soft blank nosepieces for cutter inserts, can also be
designed and manufactured to customer specifica-
tions.
Quick Change Tapholders
51 Series quick change tapholders are especially
designed for applications in which machine feed
does not exactly match that produced by t he tap
pitch . Parallel float compensates for misal ignment
conditions between the hole to be tapped and the
machine spindle.
51 Series tapholders offer:
• Quick chang e- a finger operated sleeve enab les
fast tool change to reduce machine downtime.
• Close center tooling- the sma ll overall toolhold -
er diameter allows too ling on close center dis-
tances.
• Sensitive pressure compensation-a compression
spring neutralizes feed rate variations to ensure
that ideal pressure is applied to the tool at the
beginning of the cut.
• Built-in protection-if the drilling operation has
been omitted, tool holders collapse within them-
selves to prevent tool breakage. All tapholder
models are available w ith or without compres-
sion and tension features.
Hydraulic Chucks
Hydraulic expansion chucks guarantee a maximum
runout of 0.00012-inches at two times the tool
shank diameter. This provides a balanced chip load
and increased part quality. Reduced wear pro longs
tool life as much as 300 percent.
Hydraulic expansion chucks can be operated at
very high speeds. Additional balancing is recom-
mended for speeds above 15,000 RPM. The special
resilient sleeve design enab les hydraulic expansion
chucks to clamp cylindrica l shanks up to 1.250-i nch
diameter and Weldon flats shanks up to 0.75-inch.
The slimmer design of all hydrau lic chucks per-
mits operation in difficult working situations. In-
terchangeabl e collet types can be inserted with
variable shank diameters using one hydrauli c ex-
pansion chuck. The radial runout ofthese hydraulic
chucks with collets is less than 0.0002-inch.
The complete line of hydraulic chucks incl udes
CAT, BT, HSK and flange-mounted models. Each
chuck style is available with thru -coolant capacity.
Quick-Change Straight ShankToolholders
Straight shank tool holders and automotive collet-
type holders can be used in existing automotive
spindles with over-the-spindle adapters to trans-
form any spindle, regardless of original manufac-
turer, into a qu ick-change design . Benefits of the
system include increased machining efficiency, high
accuracy repeatability and quick-change ability .
Each straight shank toolholder assembly includes
a body, collet, collet nut and snap ring, positive
drive and preset screw assembly as well as a rubber
washer for thru -coolant applications. In operation,
the tool holder is locked into the spindle by rotat-
ing the spind le mounted collar against the Acme
left hand thread on the tool holder body.
Three different body sizes are available in each
model to accommodate tools ranging from 7/ 64
(2 .7788 mm) to 3J4-inch (19.0500 mm) in diameter.
Each straight shank holder series features a guaran-
teed accuracy within 0.001 T.I.R. runout 2-inches
from the collet face . This is measured by a zero
spindle and a class XX gage pin.
Over.:rhe-Spindle Adapter AsselDblies

Over-the-spindle adapters transform standard high (standard or stub model) forces chips away from
production machine spindles into quick-change ad- the spindle face . Details are hardened and ground
justable tool adapters. They can be used with for consistent accuracy and are available to f it every
straight shank holders, automotive collet type hold- machine builder's standard spindles.
ers or existing automotive shank tool -
holders by using a standard spindle
collar and adapter nut assembly.
Located directly onto the spindle
outside diameter and securely fastened
by a locking set screw, the over-the-
spindle adapter assemblies feature a
left-hand threaded collar that forces
an Acme left hand threaded adapter
nut to seat directly against the spindle
fa ce. This enables the sp indle to take
the thrust generated by the tool, el im i-
nating any thrust being directed to the
set screw .
When loosened, the mechanically
activated over-the -spindle adapter
Collets
Precision collets feature a single angle
design D .D. with a ground and lapped
I.D. manufactured to within 0.0001-
inches ofthe required tool shank diam-
eter. A single split through the collet
allows tool clamping without losing
accuarcy, unlike other collets with mul -
tiple splits which lose accuracy while
allowing wider tool shank ranges. Six
individual col let sizes are available to
accommodate tools ranging from 1/16-
inch to Pis-inches in diameter.
These collets can be used in conjunc-
tion with tapered and stra ight shank
tool holders or w ith other tool holder
designs where clamping accuracy is es-
sential.
Precision Spindles
In addition to quick-change • Ford Motor Company:
tool holders and accessories, FL- Engine block, cylinder head,
Tool Holders has years of experi - crankshaft, camshaft; transmis-
ence with the very close toler- sion carrier, stator support,
ance work required for sp indle va lve bod ies.
manufacturing today. • General Motors Corporation:
When existing spindle designs Cylinder head, cam carrier and
are available, FL-Tool Holders can rear axle bolt holes.
assist clients in determin ing the • Chrysler Corporation :
operations needed to complete Cylinder head retoo l, exhaust
the spindle and to manufacture manifold and transmission
comp lete spindles to meet spe- case .
cific customer requirements. • Litton Industrial Automation:
Spindles and toolholders are Lamb Technicon Division
used in many manufacturing • Giddings & Lewis
plants throughout North • Ann Arbor Machine
America . Among the companies • R&B Machine
that benefit from using FL-Tool • Standard Machine
Holders are : • Western Machine
Gun DrilllReamer Toolholders
Gun drill/reamer holders provide a guaranteed accuracy
of 0.0001 T.I.R., two inches from the front face of the
collet. This toolholder is available in four separate sizes to
accommodate tool shank sizes of V4, 5/16, 3/8, 7/16, V2, 9/16, 5/8 ,
1V16 and 3f4-inches.
The basic construction of the holder assembly includes
a Jacobs type beveled tooth nosepiece, a precision ta-
pered collet and nut assembly that securely clamps and
unclamps the tool from the holder and an internal flat
that provides positive drive for the tool. Each tool holder
also features thru-coolant capability and radial position-
ing for diamond tipped tools.
Toolsetting Fixtures
FL-Tool Holders manufactures and stocks
various kinds of toolsetting fixtures.
Among the systems available are turret
type, flange type, slide type, electronic
and indicator. SOV tapered adapters,
replaceable bushings and special appli-
cations can be designed and built to
accommodate specific customer re-
quirements.
36010 Industrial Road - Livonia, Michigan 48150

Telephone 734-591-0134 - FAX 734-591-7866
www.fltoolholders.com
AGC-377/94 Litho In USA

FL-Tool Holders
Quick-Change Tapered Tool Holders
Increase Positioning Accuracy to
Improve Product Quality
Quick-change tapered Positive drive of the tool is Capability is provided for in each
Tool holder Assemblies are de- achieved by a non-rotating tool holder body size.
signed and built to increase square drive that accepts the These features make tapered
product quality by positioning tool tang as well as an adjust- tool holders ideally suited to
cutting tools accurately on pro- able preset screw for adjusting meet the demands of today's
duction and non-production ma- tool height. manufacturing specifications for
chines . The tapered tool holder Mounted to the spindle , the col- multiple spindle applications .
assembly is available in six lar is rotated in a clockwise di- Additional services include train-
separate body sizes to accom- rection to mate with the Acme ing, designing and building spe-
modate a wide variety of tool left hand thread on the tool cials , modification of standards
shank diameters beginning at holder body seating the taper and spindle manufacturing .
1/16-inch (1.5 mm) diameter. into the spindle. (See photo il-
Each patented tool holder fea- lustration on page 3.)
tures a precision full length ta- The tapered tool holder's com-
pered 0 .0 . shank (3.500 inches/ pact design minimizes spindle-
foot on diameter) and I. O. ta- to-spindle center distance as
pered collet seat (10° included) well as overhang from the spin-
to locate the cutting tool center- dle end to the bearing journal
line accurately. diameters. Thru-coolant
Tapered tool holder assemblies feature a guaranteed accuracy of .0005 TI.R. runout 2-inches our from the collet face .
2-------------------------------------------------------------------------
36010 INDUSTRIAL ROAD. LIVONIA, MI48150
Tapered Tool Holders
System Operation
1. 3.
To load the quick·change tapered tool holder ,simply inert the holder into the Rotate the spindle mounted collar in a clockwise direction until tapers are
corresponding machine tool spindle. seated. Tighten securely with spindle collar wrench.
2.
Table of Contents
Tool Holder and Spindle Collar Assembly ......... .. ... 4
Collet and Nut Assembly .. .. ........ .......... ............ . 4
Tapered Tool Holder Assembly with Collet. ... ..... .. .. 5
Tapered Tool Holder Assem bly without Collet.. .. .. ... 6
Tapered Tool Holder with Collet Nut ........ .... .. ........ 7
Tapered Tool Holder Blank...... .......... .... . .... ...... .. 7
Tapered Tool Holder Components ....... .. .. .. .. ......... 8
Keep advancing the tapered shank holder into the spindle until it comes to
a stop. At this point, the Acme left hand thread will be positioned against Quick Change Tapered Body ............... .. .......... .... 8
the spindle collar. Tool Holder Seal and Snap Ring .... ... .. .. . .. .. .......... 8
Collet Nut .. . ... ... .. .. ...... ...... ...... .. .... .......... . ......... 9
Collet Snap Ring .. .. ..... ...... .. .... ..... ......... ...... .. .. . 9
Collets ............ ... ... . ........... ... .... ... .. ... ............ .. . 9
Positive Drive and Pre-Set Screw Assembly ...... .. ... 10
Rubber Washer ... ......... ... ............ .. ... ' " ... ... ... .. .. 11
Spindle Components ............. ....... .. .... ... .. ... .. .. .. .. 12
Spindle Collar and Retaining Ring ....... ..... ... ... ... .. 12
Open End Spindle Wrench ........ . ........ ... . .... .. ...... . 12
Open End Spindle Collar Wrench ...... ...... ... ...... .... 12
Socket Spindle Collar Wrench... ... .. . ... ...... ... ... .... 13
Holding Adapter for Tool Change .. . ... ........... ........ . 13
Spindle Cleaning Swab ........ .... """ ............. .. ..... 13
Tool Setting Fixture Assembly .. .... ..... ...... .... .. .. .... 14
. Tool Setting Fixture ........................................... 14
Screwdriver Adapter .. .. .. .... .... . ..... .. ... .... . .. . .. ... .... 14
Tool Setting Fixture ...... .............. ....... .. .. ...... ...... 14
Toque Wrench (3/8" Drive) .. .. ..... ... ... .. ............ ..... 15
Crowsfoot for Collet Nut. .. ........ . ........... .......... .... . 15
Snap Ring Pliers ...... .............. .. ......................... 15
Toolsetting Fixtures .. . .. .......... .................... ...... .. 16
This is measured by a zero spindle and a class XX gage pin.
------------~----~----------~----~~--------------------------------------3
PHONE: 734·591·0134· FAX: 734-591·7866
FL-Tool Holders
Tool Holder and Spindle Collar Assembly

~---H---~ NOTE: Full scale drawing templates of tool
-- holder assemblies and components

TOOL SET RANGE
E REF. are available for assistance in tool layouts,
t<tSPINDLE alterations or new designs.
IMiN~UM
D REF. FL- Tool Holders will supply CAD
C
disks upon request.
I :'LEAR. SPINDLE
TO SPINDLE
I M~N. CENTER
~ISTANCE
B
SPDL. -
/,---
~ - -
__ J
DIA. 'ii. ___ r-"1:I.._ _lJ
TOOL
RANGE
GAGE LINE
SPINDLE END
A·TOOL SIZE A·TOOL SIZE B·MIN. C·MIN. 0 E F G H

SERIES MAX
INCHES MM SPOL. CENTER REF . REF. REF . REF. MIN.
1002 .0625 - .2500 1.5875 - 6.3500 .940 1.375 1.10 1.20 1.27 1.06 1.12 1.85
2002 .0625 - .3750 1.5875 - 9.5250 1.315 1.750 1.37 1.47 1.65 1.06 1.20 2.60
3002 .1094 - .5000 2.7788 - 12.7000 1.565 2.000 1.53 1.63 1.90 1.06 1.50 3.10
4002 .1094 - .7500 2.7788 - 19.0500 2.065 2.500 1.57 1.74 2.40 1.06 2.30 4.00
5002 .2500 - 1.0000 6.3500 - 25.4000 2.565 3.00 1.90 2.10 2.88 1.18 3.00 4.80
6002 .3750 - 1.3750 9.5250 - 34.925 3.06 3.50 2.06 2.26 3.38 1.18 2.70 5.30
Collet and Nut Assembly
GAGE LINE
COLLET NUT~ MINIMUM
CLEARANCE
CO~ff _~I
TOOL SIZE TOOL SIZE
SERIES A B C 0 E F
~ ~
INCHES MM
F
.75
COLLET 1002 .0625 - .2500 1.5875 - 6.3500 .22 .12 .48 .438 .87
SNAP RING
HEX
1.06
2002 .0625 - .3750 1.5875 - 9.5250 .22 .12 .57 .563 1.23
HEX
1.25
3002 .1094 - .5000 2.7788 - 12.7000 .26 .16 .64 .720 1.44
HEX
1.75
4002 .1094 - .7500 2.7788 -19.0500 .30 .19 .70 1.131 2.02
HEX
NOTE: The collet and nut are not sold as 2.50
5002 .2500 - 1.0000 6.3500 - 25.4000 .42 .21 .84 1.446 2.50
an assembly. See individual components OIA
for part numbers.
3.00
6002 .3750 - 1.3750 9.525 - 34.925 .47 .21 .84 1.910 3.00
DIA
4---------------------------------------------------------------------------------
Tapered Tool Holder Assembly with Collet
NOTE:
Tool Holder assembly includes Body,
Collet, Collet Nut, Collet Snap Ring,
Tool Holder Seal, Tool Holder Snap
Ring, Positive Drive and Pre-Set Screw
Assembly. Ordering Information
A·TOOL SIZE A·TOOL SIZE A·TOOL SIZE A·TOOL SIZE
SERIES PART NUMBER SERIES PART NUMBER
INCHES MM INCHES MM
.0625 - .1249 1.5875 - 3.1725 l oo2·ooo·E/MXXXX·K .3750 - .4687 9.5250 - 11.9050 4oo2·oo5·E/MXXXX·K
1002 .1250- .1874 3.1750 - 4.7600 l oo2·oo1·E/MXXXX·K .4688 - .5624 11.9075 - 14.2850 4oo2·oo6·E/MXXXX·K
4002
.1 87 5- .2500 4.7625 - 6.3500 l O02·o02·E/MXXX X·K .5625 - .6561 14.2875 - 16.6649 4oo2·oo7·E/MXXXX·K
.0625 - .1249 1.5875 - 3.1725 2oo2·ooo·E/MXXXX·K .6562 - .7500 16.6675 - 19.0500 4oo2·ooB·E/MXXXX·K
.1250- .1 874 3.1 750 - 4.7600 2002·00 l ·E/MXXXX·K .2500 - .3124 6.3500 - 7.9350 5oo2·oo3·E/MXXXX·K
2002 .1875 - .2499 4.7625 - 6.3475 2oo 2·oo 2·E/MXXXX·K .3125- .3749 7.93 75 - 9.5225 5oo2·oo4·E/MXXXX·K
.2500- .3124 7.93 75 - 95250 2oo2·oo3·E/MXXXX·K .3750 - .4687 9.5250 - 11 .9050 5oo2·oo5·E/MXXXX·K
.3125 - .3750 6.3500 - 7. 9350 2oo2·oo4·E/MXXXX·K .4688 - .5624 11.9075 - 14.2850 5oo2·oo6·E/MXXXX·K
500 2
.1094 - .1249 2.77 88 - 3.1725 3oo2·2oo·E/MXXXX·K .5625 - 6561 14.2875 16.6649 5oo2·007·E/MXXXX·K
.1250 - .1 874 3.1750 - 4.7600 Jo02·oo1 ·E/MXXXX·K .6562 - .7499 16.6675 - 19.0475 5oo2·ooB·E/MXXXX·K
.1875 - .2499 4.7625 - 6.3475 3002·o02·E/MXXXX·K .7500 - .8749 19.0500 - 22.2225 5oo2·oo9·E/MXXXX·K
3002 .2500 - .3124 6.3500 - 7.9350 Jo02·ooJ·E/MXXXX·K .8750 - 1.000" 22.2250 - 25.4000 5oo2·010·E/MXXXX·K
.3125 - .3749 7.9375 - 9. 5225 Jo02·oo4·E/MXXXX·K .3750 - .4687 9.5250·11 .9050 6oo2·oo5·E/MXXXX·K
.3750 - .4687 9.5250 - 11.9050 Jo02·oo5·E/MXXXX·K .4688 - .5624 11 .9075 - 14.2850 6oo2·oo6·E/MXXXX·K
.4688 - .5000 11 .9075 - 12.7000 3oo2·oo6·E/MXXXX·K .5625 - 6561 14.2875 -1 6.6649 6oo2·oo7·E/MXXXX·K
.1094 - .1249 2.7788 - 3.1725 4002·ooo·E/MXXXX·K .6562 - .7499 16.6675 - 19.0475 6oo2·0oB·E/MXXXX·K
6002
.1250 - .1874 3.1750 - 4.7600 4oo2·oo1 ·E/MXXXX·K .7500 - .8749 19.0500·22.2225 6002·009·E/MXXXX·K
4002 .1875 - .2499 4.7625 - 6.3475 4oo2·oo2·E/MXXXX·K .8750 - 9999 22.2250 - 25.3975 6oo2·010·E/MXXXX·K
.2500 - .31 24 6.3500 - 7.9350 4oo2·oo3·E/MXXXX·K 1.0000 - 1.1 874 25.4000 - 30.1600 6oo2·o11 ·E/MXXXX·K
.31 25 - .3749 7.9375 - 9.5225 4oo2·oo4·E/MXXXX·K 1.1875 - 1.3750 30.1625 - 34.9250 6002·o12·E/MXXXX·K
To order a complete tool holder assembly (with NOTES: 1. It is re commended that all tools have tang drives.
collet) . you must have the following information:
1. Tool holder series
2. Pre-set screw size (see tables above using tool
size to determine part number)
3. Specify English (E) or Metric (M)
4. Tool Shank size for collet 1.0. (See page 7 for
proper collet ordering information).
5. Specify (K) if Thru-Coolant application is required .
Example: _002 - 00_- _ _ -K
~ ~ ~ ~ ~
(1) (2) (3) (4) (5)
------------------------------------------------------------------------------------5
PHONE: 734·591·0134· FAX: 734·591·7866
FL-Tool Holders
Tapered Tool Holder Assembly without Collet
NOTE:
Tool Holder assembly includes Body,
Collet Nut, Tool Holder Seal, Tool
Holder Snap Ring, Positive Drive and
Pre-Set Scre w Assembly.
Ordering Information
SERIES A·TOOL SIZE A·TOOL SIZE PART NUMBER SERIES A·TOOL SIZE A·TOOL SIZE PART NUMBER
.0625 - .1249 1.5875 - 3.1725 1002·000 .3750 - .4687 9.5250 - 11 .9050 4002 ·005
1002 .1250 - .1874 3.1750 - 4.7600 1002·001 .4688 - .5624 11 .9075 - 14.2850 4002·006
4002
.1 875 - .2500 4.7625 - 6.3500 1002·002 .5625 - .6561 14.2875 - 16.6649 4002·007
.0625 - .1249 1.5875 - 3.1725 2002·000 .6562 - .7500 16.6675 - 19.0500 4002·008
.1250 - .1 874 3.1750 - 4.7600 2002·001 .2500 - .3124 6.3500 - 7.9350 5002·003
2002 .1875 - .2499 4.7625 - 6.3475 2002·002 .3125 - .3749 7.9375 - 9.5225 5002·004
.2500 - .3124 6.3500 - 7.9350 2002·003 .3750 - .4687 9.5250 - 11 .9050 5002·005
.3125 - .3750 7.9375 - 95250 2002·004 .4688 - .5624 11 .9075 - 14.2850 5002·006
5002
.1094 - .1249 2. 7788- 3.1725 3002·200 .5625 - 6561 14.2875 16.6649 5002·007
.1250 - .1874 3.1750 - 4.7600 3002·001 .6562 - .7499 16.6675 - 19.0475 5002·008
.1875 - .2499 4.7625 - 6.3475 3002·002 .7500 - .8749 19.0500 - 22.2225 5002·009
300 2 .2500 - .31 24 6.3500 - 7.9350 3002·003 .8750 - 1.000 " 22.2250 - 25.4000 5002·010
.3125 - .3749 7.9375 - 9.5225 3002·004 .3750 - .4687 9.5250·11 .9050 6002·005
.3750 - .4687 9.5250 - 11 .9050 3002·004 .4688 - .5624 11 .9075 - 14.2850 6002·006
.4688 - .5000 11.9075 - 12.7000 3002·006 .5625 - 6561 14.2875 - 16.6649 6002·007
.1094 - .1 249 2. 7788 - 3. 1725 4002·000 .6562 - .7499 16.6675 - 19.0475 6002·008
6002
.1250 - .1874 3. 1750 - 4.7600 4002·001 .7500 - .8749 19.0500·22.222 5 6002·009
4002 .1875 - .2499 4.7625 - 6.3475 4002·002 .8750 - 9999 22.2250 - 25.3975 6002·010
.2500 - .3124 6.3500 - 7.9350 4002·003 1.0000 - 1.1874 25.4000 - 30.1600 6002·011
.3125 - .3749 7.9375 - 9.5225 4002·004 1.1875 - 1.3750 30.1625 - 34.9250 6002·012
To order a complete tool holder assembly (without NOTES: 1. It is recommended that all tools have
collet), you must have the followi ng information: tang drives.
1. Tool holder series
2. Positive drive size (see tables above using tool
size to determi ne part number)
Example: _002 - 00_
~ ~
(1) (2)
6------------------------------------------------------------------------------
36010 INDUSTRIAL ROAD • LIVONIA, MI 48150
Tapered Tool Holder with Collet Nut
NOTE:
Tool Holder includes Tool Holder Body,
Tool Holder Seal, Tool Holder Snap
Ring and Collet Nut.
SERIES PART NUMBER
1002 1002·BN
2002 2002·BN
3002 3002·BN
1. Locate desired Series number.
2. Order by Part Number listed . 4002 4002·BN
5002 5002·BN
6002 6002·BN
Tapered Tool Holder Blank (Solid)
NOTE:
Tool Holder includes Tool Holder Seal
I BDIA.
and Snap Ring. These solid holders are
to plug spindles when not being used.
~ SERIES PART NUMBER A B
1002 1002·BLANK 1.00 .62
2002 2002·BLANK 1.25 .88
3002 3002·BLANK 1.38 1.06
4002 4002·BLANK 1.38 1.56
5002 5002·BLANK 1.50 2.12
1. Locate desired Series number. 6002 6002·BLANK 1.50 2.50
2. Order by Part Number listed .
------------------------------------------------------------------------------------ 7
PHONE: 734-591-0134· FAX: 734-591-7866
FL-Tool Holders
Tapered Tool Holder Components
TOOL HOLDER
SEAL
SPINDLE COLLAR (See page 8) COLLET
(See page 11) SNAP RING
TOOL HOLDER BODY TOOL HOLDER (See page 9)
(See page 8) SNAP RING
(See page 8) COLLET
(See page 9)
SPINDLE POSITIVE DRIVE and

RETAINING PRE-SET SCREW
ASSEMBLY RUBBER WASHER COLLET NUT
RING
(See page 11) (See page 10) (Thru-coolant only) (See page 9)
(See page II)
Quick-Change Tapered Body

1. Locate desired Series number. SERIES PART NUMBER A B C 0
2. Order by Part Number listed.
1002 1002·B .6875 7/8 -12 1.005 2.27
GAGE
DIA. r B
2002 2002·B 1.000 11/4- 12 1.245 2.93
3002 3002·B 1.250 11/2-12 1.375 3.56
4002 4002·B 1.750 2 -12 1.375 4.16

'.
5002 5002·B 2.250 21/2 - 12 1.685 5.03
6002 6002·B 2.750 3 -12 1.850 5.85
Tool Holder Seal and Snap Ring

SERIES PART NUMBER SERIES PART NUMBER
1000 1002·TS 1000 1002·TSR

2000 2002·TS 2000 2002·TSR
3000 3002·TS 3000 3002·TSR

4000 4002·TS 4000 4002·TSR
5000 5002·TS 5000 5002·TSR
6000 6002·TS 6000 6002·TSR
2. Order by Part Number listed. NOTE: Snap rings are manufactured by
Spir%x Company.
8 ------------------------------------------------------------------------------------
36010 INDUSTRIAL ROAD. LIVONIA, MI 48150
Collet Nut
---. A .--
D.A.l. SPANNER NUT
tB
MINIMUM SERIES PART NUMBER A B C 0
CLEARANCE
DIAMETER 1002 1002·N .477 .87 9/16 - 28 3/4
+-0_
WRENCH
• 2002
3002
2002·N
3002·N
.571
.644
1.23
1.44
13/16-12
1 - 12
11/16
11/4
SIZE 4002 4002·N .696 2.02 11/2 - 12 1 3/4

Ordering Information 5002 5002·N .840 2.50 2.0 -12 SPANNER
1. l.ocate desired Series number.
2. Order by Part Number listed . 6002 6002·N .840 3.00 25/16-12 SPANNER
Collet Snap Ring

Ordering Information SERIES PART NUMBER
1. Locate desired Series number. 1002 1002·SR
2002 2002·SR
3002 3002·SR
4002 4002·SR NOTE: Snap rings
are manufactured by
5002 5002·SR Tru-Arc Company.
6002 6002·SR
Collets
SNAP RING
REFERENCE
SERIES PART NUMBER A·TOOL SIZE A·TOOL SIZE B C

(
GAGE 1002 1002·E/M (KI .0625 - .2500 1.5875 - 6.3500 1.005 .4390
DIAMETER
2002 2002·E/M (K) .0625 - .3750 1.5875 - 9.5250 1.035 .5630
1. Order by Part Number. 3002 J002·E/M (K) .1094 - .5000 2.7788 - 12.7000 1.185 .7200
2. Specify English or Metric
4002 4002·E/M (K) .1094 - .7500 2.7788 - 19.0500 1.770 1.1310
3. To determine proper collet ID size, use the high
tolerance limit on the tool shank. 5002 500H/M (K) .2500 - 1.0000 6.350 - 25.4000 2.200 1.4460
Example: A 4000 Series collet used with a .7500 +.0000/-
6002 6002·E/M (K) .3750 - 1.3750 9.5250 - 34.9250 2.700 1.9100
.0005 diameter tool shank requires collet Part Number
4002 - E7500.
NOTE: These are precision collets, manufactured within ±.0001-
Add 'K' at end of part number if Thru-Coolant is required inch of specified tool shank size. FL- Tool Holders recommends a
(a rubber washer will be supplied). + .0000/ - .0005 tolerance on the tool shank to ensure maximum
A snap ring is supplied with each collet item ordered. accuracy and clamping performance (up to - .0015 tolerance is
acceptable if necessary.) Shank taper should no exceed .0002.
------------------------------------------------------------------------------------9
PHONE: 734·591·0134· FAX: 734·591·7866
FL-Tool Holders
Positive Drive and Pre-Set Screw Assembly
Ordering Information B~ III( ..
1. Locate desired Series number. O.A.L. I
2 Use Tool Shank Size to determine HEX FOR --.. D '-.1 1001 SERIES ONLY
correct Part Number. ALLEN WRENCH T
NOTE: It is recommended that all tools

have tang drives.
LEFT HAND
THREAD
SERIES PART NUMBER A·TOOL SIZE A·TOOL SIZE A B C D E TANG
1002·0 .0625 - .1249 1.5875 - 3.1725 NO SLOT 5/64 --

1002 1002·1 .1250 - .1874 3.1750 - 4.7600 5/16 - 24 .31 .096 .18 5/64 .094 - .090
1002·2 .1875 - .2500 4.7625 - 6.3500 .125 .18 5/64 .122 -. 118
2002·0 .0625 - .1249 1.5875 - 3.1725 NO SLOT 7/64 --
2002·1 .1250- .1874 3.1750 - 4.7600 .096 .18 7/64 .094 - .090
2002 2002·2 .1875 - .2499 4.7625 - 6.3475 7/16 - 20 .70 .125 .18 7/64 .122 - .118
2002·3 .2500 - .3124 6.3500 - 7.9350 .172 .22 7/64 .162 - .158
2002·4 .3125 - .3750 7.9375 - 9.5250 .213 .22 7/64 .203 - .199
3002·0 .0625 - .1249 1.5875 - 3.1725 NO SLOT 7/32 --
3002·1 .1250- .1874 3.1750 - 4.7600 .096 .18 7/32 .094 - .090
3002·2 .1875 - .2499 4.7625 - 6.3475 .125 .18 7/32 .122 - .118
3002 3002·3 .2500 - .3124 6.3500 - 7.9350 9/16 - 24 .80 .172 .22 7/32 .162 - .158
3002·4 .3125 - .3749 7.9375 - 9.5225 .213 .25 7/32 .203 - .199
3002·5 .3750 - .4687 9.5250 -11 .9050 .253 .25 7/32 .243 - .239
3002·6 .4687 - .5000 119050 - 12.7000 .313 .25 7/32 .303 - .297
4002·0 .1094- .1249 2.7788- 3.1725 NO SLOT 5/16 --
4002·1 .1250 - .1874 3.1750 - 4.7600 .096 .25 5/16 .094 - .090
4002·2 .1875 - .2499 4.7625 - 6.3475 .125 .25 5/16 .122- .118
4002·3 .2500 - .3124 6.3500 - 7.9350 .172 . .31 5/16 .162 - .158
4002 4002·4 .3125 - .3749 7.9375 - 9.5225 13/16 - 20 .85 .213 .31 5/16 .203 - .199
4002·5 .3750 - .4687 9.5250 - 119050 .253 .31 5/16 .243 - .239
4002·6 .4687 - .5624 119050 -14.2850 .313 .31 5/16 .303 - .297
4002·7 .5625 - .6561 14.2875 - 16.6649 .383 .31 5/16 .373 - .367
4002·8 .6562 - .7500 16.6675 - 19.0500 .453 .31 5/16 .443 - 4.37
5002·3 .2500 - .3124 6.3500 -7.9350 .172 .31 7/16 .162- .158
5002·4 .3125 - .3749 7.9375 - 9.5225 .213 .31 7/16 .203- .199
5002·5 .3750 - .4687 9.5250 - 11 .9050 .253 .31 7/16 .243 - .239
5002·6 .4687 - .5624 119050 - 14.2850 .313 .31 7/16 .303 - .297
5002 1 1/8 -..20 1.00
5002·7 .5625 - 6561 14.2875 -16.6650 .383 .31 7/16 .373 - .367
5002·8 .6562 - .7499 16.6675 - 19.0475 .453 .38 7/16 .443 - .437
5002·9 .7500 - .8749 19.0500 - 22.2225 .524 .38 7/16 .514 - .508
5002·10 .8750 - 1.000 22.2250 - 25.4000 .620 .38 7/16 .609 - .601
6002·5 .3750 - .4687 9.5250 - 11.9050 .253 .31 1/2 .243 - .239
6002·6 .4687 - .5624 11 .9050- 14.2850 .313 .31 1/2 .303 - .297
6002·7 .5625 - .656 1 14.2875 - 16.6650 .383 .31 1/2 .373 - .367
6002·8 .6562 - .7499 16.6675 - 19.0475 .453 .38 1/2 .443 - .437
6002 11/2 - 2,0 1.25
6002·9 .7500 - .8749 19.0500 - 22.2225 .524 .38 1/2 .514 - .508
6002·10 .8750 - .9999 22.2250 - 25.3975 .620 .38 1/2 .609 - .601
6002·11 1.0000 -1.1874 25.4000 - 30.1600 .710 .44 1/2 .700 - .692
6002·12 1.1875 - 1.3750 30.1625 - 34.9250 .827 .44 li2 .817 - .809
10---------------------------------------------------------------------------------
Rubber Washer
2. Use Tool Shank Size to determine
correct Part Number
10 PART TOOL SIZE TOOL SIZE
PART TOOL SIZE TOOL SIZE SERIES
SERIES MM NUMBER INCHES MM
NUMBER INCHES
1002·RWO .180·.200 4.57·5.08 5002·RWI .250·.260 6.35·6.60
1002·RWOA .201 ·.220 5.10·5.59 5002·RW2 .261·.300 6.63·7.62

1002
1002·RW1 .221·.240 5.61·6.10 5002·RW3 .301 ·.340 7.64·8.64
1002·RW1A .24 1·.250 6.12·6.35 5002·RW4 .341·.380 8.66·9.65
2002·RWO .180·.200 4.57·5.08 5002·RW5 .381 ·.420 9.68· 10.67

2002·RWOA .201 ·.220 5.10·5.59 5002·RW6 .421·.460 10.69·11.68
2002·RW1 .22 1·.240 5.61 ·6.10 5002·RW7 .461·.500 11.71·12.70
2002·RW1A .241·.260 6.12·6.60 5002·RW8 .501 ·.540 12.72-13.72
2002·RW2 .261 ·.280 6.63·7.11 5002·RW9 .541 ·.580 13.74·1 4.73
2002 2002·RW2A .281 ·.300 7.14-7.62 5002·RW10 .581 ·.620 14.75·15.75
5002
2002·RW3 .301 ·.320 7.64·8.13 5002·RW11 .621·.660 15.77- 16.76
2002·RW3A .32 1·.340 8.15·8.64 5002·RW12 .661 ·.700 16.79·17.78
2002·RW4 .341 ·.360 8.66·9.14 5002·RW13 .701-.740 17.80·18.80
2002·RW4A .361 ·370 9.17·9.40 5002·RW14 .741 ·.780 18.82·19.81
2002·RW5 .371 ·.375 9.42·9.53 5002·RW15 .781·.820 19.83·20.83
3002·RWO .180·.200 4.57·5.08 5002·RW16 .821 ·.860 20.85·21.84
3002·RWOA .201 ·.220 5.10·5.59 5002·RW17 .861 ·.900 21 .87·22.86
3002·RWI .221·.240 5.61 ·6.10 5002·RW18 .901·.940 22.88·23.88
3002·RWIA .241 ·.260 6.12·6.60 5002·RW19 .941·.980 23.90·24.89
3002·RW2 .261 ·.280 6.63·7.11 5002·RW20 .98 1·1.00 24.92·25.40
3002·RW2A .281·.300 7.14·7.62 6002·RW4 .375·.380 9.53·9.65
3002·RW3 .301·.320 7.64·8.13 6002·RW5 .381 ·.420 9.68·10.67
3002·RW3A .321 ·.340 8.15·8.64 6002·RW6 .421·.460 10.69·11.68
3002
3002·RW4 .341 ·.360 8.66·9.14 6002·RW7 .461·.500 11.71 ·12.70
3002·RW4A .361 ·.380 9.17·9.65 .6002·RW8 .501 ·.540 12.72- 13.72
3002·RW5 .381 ·.400 9.68·10.16 6002·RW9 .541 ·.580 13.74·14.73
3002·RW5A .401 ·.420 10.18·10.67 6002·RW10 .581 ·.620 14.75·15.75
3002·RW6 .421·.440 10.69·11.18 6002·RWll .621 ·.660 15.77- 16.76
3002·RW6A .441·.460 11 .20·11 .68 6002·RW12 .661 ·.700 16.79·17.78
3002·RW7 .461 ·.480 11.71·12.19 6002·RW13 .701 ·.740 17.80·18.80
3002·RW7A .481 ·.500 12.22·12.70 6002·RW14 .741 ·.780 18.82·19.81
4002·RWO .180·.220 4.57·5.59 6002·RW15 .781 ·.820 19.83-20.83
4002·RWI .221·.260 5.61 ·6.60 6002·RW16 .821·.860 20.85·21.84
6002
4002·RW2 .261 ·.300 6.63·7.62 6002·RW17 .861 ·.900 21.87·22.85
4002·RW3 .301·.340 7.64·8.64 6002·RW18 .901 ·.940 22.88·23.88
4002·RW4 .341 ·.380 8.66·9.65 6002·RW19 .941 ·.980 23.90·24.89
4002·RW5 .381 ·.420 9.68·10.67 6002·RW20 .981-1.020 24.92·25.91
4002·RW6 .421 ·.460 10.69·11.68 6002·RW21 1.021-1.060 25.93·26.92
4002 4002·RW7 .461 ·.500 11.71·12.70 6002·RW22 1.061 ·1.1 00 26.95·27.94
4002·RW8 .501·.540 12.72-13.72 6002·RW23 1. 101 ·1.140 27.96·28.96
4002·RW9 .541 ·.580 13.74·14.73 6002·RW24 1.141 ·1.180 28.98·29.97
4002·RW10 .581 ·.620 14.75·15.75 6002·RW25 1.1 81-1.220 30.00·30.99
4002·RW11 .621 ·.660 15.77-16.76 6002·RW26 1.221-1.260 31 .01 ·32.00
4002·RW12 .661 ·.700 16.79·17.78 6002·RW27 1.261·1.300 32.03-33.02
4002·RW13 .701 ·.740 17.80·18.80 6002·RW28 1.301-1.340 33.04·34.04
4002·RW14 .741 ·.750 18.82·1 9.05 6002·RW29 1.341-1.375 34.06·34.93
11
PHONE: 734-591-0134· FAX: 734-591-7866
FL-Tool Holders
Spindle Components
TAPERED TOOL HOLDER SERIES PART NUMBER
BLY 1002 1002·CR
2002 2002·CR
3002 3002·CR
4002 4002·CR
5002 5002·CR
Ordering Information 6002 6002·CR
NOTE: Spindle components consist of a collar
and retaining ring. They may be purchased
Individually or as an assembly.
Spindle Collar and Retaining Ring

SERIES PART NUMBER A SERIES PART NUMBER
1002 1002·C 7/8 - 12 1002 1002·R
2002 2002·C 11/4 - 12 2002 2002·R
3002 3002·C 1 1/2 - 12 3002 3002·R
4002 4002·C 2 -1 2 4002 4002·R
5002 5002·C 2.5 -1 2 5002 5002·R
1. Locate desired Series number. 6002 6002·C 3 - 12 6002 6002·R
Open End Spindle Wrench

I. A "I
SERIES
100i .
2002
PART NUMBER
100Z·WSP·S
ZOOZ·WSP·S
ADIM
10.00
10.00
B DIM
.82
1.20
3002 300Z-WSP·S 12.00 1.44
4002 400Z·WSP·S 12.00 1.94
5002 5002·WSP·S 12.00 2.38
Ordering Information 6002 600Z-WSP·S 12.00 2.86

1. Locate desired Series number. NOTE: This wrench is used to retain the spindle
2. Order by Part Number listed . when loosening or tightening the spindle collar if
necessary.
Open End Spindle Collar Wrench

SERIES PART NUMBER A DIM B DIM
1002 100Z·WSP 8.00 1.16
2002 ZOO2·WSP 8.00 1.53
3002 300Z·WSP 9.50 1.78
4002 400Z-WSP 9.50 2.28
5002 500Z·WSP 9.50 2. 62
Ordering Information 6002 600Z·WSP 9.50 3.1 2

1. Locate desired Series number. NOTE: It is recommended that this wrench be used
2. Order by Part Number listed. to loosen or tighten the spindle collar.
12---------------------------------------------------------------------------------
Socket Spindle Collar Wrench

I
SERIES PART NUMBER ADIA. B LENGTH
1002 1002·W 1.50 4.00
B 2002 2002·W 1.88 4.50
~
3002 3DD2·W 2.12 4.50
4002 4D02·W 2.62 4.50
5002 5002·W 3.12 4.50
Ordering Information 6002 6002·W 3.62 4.50
2. Order by Part Number listed . NOTE: It is recommended that this
wrench be used to loosen or tighten the
spindle collar.
Holding Adapter for Tool Change

SERIES PART NUMBER A LENGTH B FLATS
1002 IOD2·A 1.62 1.25
2002 2D02·A 2.12 1.50
3002 3002·A 2.62 2.00
4002 4002·A 3.25 2.50
5002 5002·A 3.90 3.00
6002 6D02·A 4.50 3.50
1. Locate desired Series number. NOTE: The holding adapter is designed to be used in a vise
2. Order by Part Number listed. to loosen or tighten the collet nut. This prevents
damage to the tool holder body.
Spindle Cleaning Swab

SERIES PART NUMBER
1002 1002·S
2002 2002·S
3002 3002·S
4002 4002·S
5002 5002·S
6002 6002·S
NOTE: These cleaning

swabs are designed for
easy cleaning of the
spindle taper.
I . Locate desired Series number.
------------------------------------------------------------------------------13
PHONE: 734-591-0134· FAX: 734-591-7866
FL-Tool Holders
Tool Setting Fixture Assembly
TAPERED TOOL HOLDER
/ SERIES AS REQUIRED
GAGE LINE
Tool Setting Fixture ---.. CERTIFIED

DIM.
SERIES PART NUMBER
1002 1002-RTF
2002 2002-RTF
3002 3002 -RTF

4002 4002·RTF
5002 5002-RTF
Ordering Information 6002 6002-RTF
1. Locate desired Series number. NOTE: These holders have
2. Order by Part Number listed . an ANSI 50V 0 _0. taper
with Series required I.D.
Screwdriver Adapter
SERIES PART NUMBER
1002 & 2002 1002 & 2002 - RTA
3002 & 4002 3002 & 4002 - RTA
5002 5002-RTA
1. Locate desired Series number. 6002 6002·RTA
2. Order by Part Number listed _ NOTE: These spring loaded adapters are used with
3. Specify Screwdriver or Hex style. tool setting fixtures instead of a screwdriver or Allen
wrench. Ends are replaceable .
Tool Setting Fixture

r
TOOL
SET
l/AGELINE SERIES
1002
PART NUMBER
1002-TSF
2002 2002-TSF
r
3002 3002·TSF
4002 4002·TSF
CERTIFIED 5002 5002·TSF

DIM. GRANITE 6002 6002·TSF
j EPLATE
1
_ .- -_ . _ . _. _. - . - . _ . -. _.
This gage is designed to be used on a granite base
plate with an indicator stand to set tool height.
14 ---------------------------------------------------------------------------------
Torque Wrench (3/8" Drive)

1. Order by Part Number.
PART NUMBER
752·MF
Crowsfoot for Collet Nut

SERIES PART NUMBER PART NUMBER PART NUMBER A
1002 752·1 752·1A N/A 3/4

2002 752·2 752·2A N/A 11/16
300 2 752·3 752·3 N/A 11/4
4002 752·4 752·4 N/A 13/4
5002 N/A N/A 752·5 2 1/2
6002 N/A N/A 752·6 3
XXXO & XXX1 SERIES USES A OCTAGON NUT

XXX2 SERIES USES A HEX NUT
*5000 & 6000 SERIES ARE SPANNER NUT ONLY
Snap Ring Pliers

PART NUMBER
B52·SRP
_________________________________________________________________________________ 15
PHONE: 734-591-0134· FAX: 734-591-7866

FL-Tool Holders
Toolsetting Fixtures
FL-Tool Holders manufactures and
stocks various kinds of toolsetting fixtures .
Among the systems available are turret
type , flange type, slide type , electronic and
indicator. 50V tapered adapters, replace-
able bushings and special applications can
be designed and built to accommodate
specific customer requirements .
16-----------------------------------------------------------------------------
36010 INDUSTRIAL ROAD • LIVONIA, MI48150
FL-Tool Holders'"
Straight Shank and Collet-Type Toolholders and

Straight shank and collet-type
tool holders can be used in exist-
ing automotive spindles with
over-the-spindle adapters to
transform any spindle, regard-
less of original manufacturer,
into a quick-change design. Ben-
efits of the systems include in-
creased machining efficiency,
high accuracy repeatability and
quick-change ability.
Three different body sizes are
available in each model to ac-
commodate tools ranging from
%4 (2.7788 mm) to %-inch
(19.0500 mm) in diameter.
Straight shank tool holders fea-
ture a guaranteed accuracy with-
in 0.001 T.LR. runout 2-inches
from the collet face. This is mea-
sured by a zero spindle and a
class XX gage pin.
Each straight shank and collet-
type tool holder assembly in-
cludes a body, collet, collet nut
and snap ring, tool holder seal
and snap ring, positive drive and
a preset screw assembly as well
as a rubber washer and rear cool-
ant seal for thru-coolant appli-
cations.
OPERATION
The close fit of the toolholder
O.D. to the spindle LD. enables
accurate and secure positioning
of the over-the-spindle adapter
collar. Mounted over an existing
spindle, the collar is rotated in a vides tool height adjustment
clockwise direction to mate with and positive drive to the tool. Features and Benefits
the Acme left-hand thread on The compact design minimizes
the toolholder body, retaining spindle-to-spindle center dis- • Increased Machining Efficiency
the holder intothespindle. Coun- tance and overhang from the
terclockwise rotation of the col- spindle end to the bearing jour- • High Accuracy Repeatability
lar forces the toolholder body nal diameters.
out of the spindle. A complete line of optional • Quitk Changeability
Each patented toolholder se- accessories complements the
ries features an automotive straight shank holder and collet • Thru-Coolant Capability
straight shank and an LD. ta- type toolholder. They include
pered collet seat that accurately toolsetting fixtures, holding
locates the cutting tool center- adapters for tool change, spin- can provide full scale drawing
line, and adjustable preset screw dle cleaning swabs and spindle templates or CAD disks for every
and drive assembly which pro- collar wrenches. FL:Tool Holders product upon request.
2 ______________________________________________________________________________
Straight Shank, Collet Type Toolholders and Over-The-Spindle Adapters
Over-The-Spindle Adapter Assemblies
Table of Contents
Adapter Assemblies ........ .. ..... 4
Adapters ............ .... ..... .. ..... ... 5
Adapter Nut .... ...... .. ...... ....... . 5
Lockscrew ......... ...... .... ..... ..... 5
Toolholder Seal .. ... ..... ... ... .. .... 5
Toolholder Snap Ring .. .... ....... 5
Straight Shank Assembly .... ... . 6
Straight Shank Components .. 7
Straight Shank Body ..... .. .... ... 7
Collet-Type Assembly ......... .. .. 8
Collet-Type Components ... .. .. 9
Collet-Type Body .. ... ..... .. ....... 9
Collet .. ... .... .. .... .. .... .. ....... ... . 10
Collet Nut ...... ... ........ ... .... .... 10
Collet Snap Ring ... ... .. .. ..... ... 10
Rubber Washer ..... ... .... ........ 10
Positive Drive and Pre-Set
Screw Assembly ........... .... 11
Rear Coolant Seals .. .... ... ..... . 11
Spindle Dimensions ..... ... ... ... 12
Socket Spindle Collar
Wrench .... .... ... .. ....... .... .... 12
Open End Spindle Collar
Wrench ..... ...... ......... .... ... . 12
Over-the-spindle adapters trans- Located directly onto the spin- thrust from being directed to
form standard high production dle outside diameter and secure- the set screw.
machine spindles into quickly fastened with a locking set When loosened, the mechani-
change adjustable tool adapt- screw, the over-the-spindle adap- cally activated over-the-spindle
ers. They can be used with ter assemblies feature a left-hand adapter (standard or stub mod-
straight shank tool holders, au- threaded collar that forces an el) forces chips away from the
tomotive collet type tool holders Acme left-hand threaded adapt- spindle face. Details are hard-
or existing automotive shank er nutto seat directly againstthe ened and ground for consistent
toolholders by using a standard spindle face . This enables the accuracy and are available to fit
spindle collar and adapter nut spindle to take the thrust gener- every machine builder'sstandard
assembly. ated by the tool, eliminating any spindles.
____________________________________________________________________________ 3
FL-Tool Holders""
Over-The-Spindle Adapter Assembly

SPINDLE END
LOCKSCREW-
-..
ADAPTER NUT NOTE: FOR RETAINING O.S.A. ONTO SPINDLE
V4-28 UNF FOR 1;2 ADAPTERS
ADAPTER SIZE 5116-24 UNF FOR REMAINING ADAPTERS
~
+.000
- .002
-r --------· E F
SPINDLE DIA.
NOTE: Assembly includes sleeve,
collar, retaining ring assembly,
adapter nut and lock screw, face seal
G and snap ring.
SPINDLE TO
SPINDLE
C~~~ER SNAP RING O.S.A .
SERIES ADAPTER
SIZE
A SSEMBLY
PART
A B C D E F G
DISTANCE FACE SEAL - lNCHES NUMBER
SLEEVE
-~----------------------------------------------
10500 112 10500AN .64 1.250 .93 1.910 1.15 .735 1.25
10625 &8 10625AN .64 1.250 .96 1.910 1.40 .985 1.50
10750 314 10750AN .64 1.250 1.01 1.910 1.65 1.235 1.75
1. Locate desired adapter size. 10875 7Al 10875AN .64 1.56 1.01 2.220 1.77 1.360 1.87
11000 1 11000AN .64 1.56 1.01 2.220 1.90 1.484 2.00
11063 1-111 6 11063AN .64 1.56 1.01 2.220 2.02 1.610 2.12
11375 1-3-8 11375AN .64 1.810 1.01 2.470 2.40 1.985 2.50
11875 1-7Al 11875AN .75 2.31 0 1.10 3.090 3.02 2.610 3.1 2
Over-The-Spindle Adapter Assembly IL--_------'

(Stub Model)
SPINDLE END ~ LOCKSCREW-
NOTE: FOR RETAINING
ADAPTER NUT\ O.S.A. ONTO SPINDLE
516-24UNF
ADAPTER SIZE
-r ---- ----D DIA.-
G NOTE: Assembly includes sleeve,

SPINDLE TO
SPINDLE collar, retaining ring assembly,
MIN. adapter nut and lock screw, face seal
CENTER ADAPTER ASSEMBLY
and snap ring.
DISTANCE
-~---------------------------------------------- SERIES ADAPTER

SIZE
-lNCHES
ASSEMBLY
PART
NUMBER
A B C D E F
Ordering Information 10750 314 10750SAN .64 1.01 1.20 1.65 1.235 1.75
1. Locate desired adapter size.
10875 7Al 10875SAN .64 1.01 1.20 1.77 1.360 1.87
11000 1 11000SAN .64 1.01 1.20 1.90 1.484 2.00
11063 1-1116 11063SAN .64 1.01 1.20 2.02 1.610 2.1 2
11375 1-3-8 11375SAN .64 1.01 1.20 2.40 1.985 2.50
11875 1-7Al 11875SAN .75 1.10 1.20 3.02 2.610 3.12
4 _________________________________________________________________________
Over-The-Spindle Adapter SIZE

SERIES INCHES PART NUMBER
10500 112 l0500A

10625 &8 10625A
10750 :¥4 10750A
10875 718 10875A
11000 1 11000A
11063 1-111 6 11063A
Ordering Information 11375 1-3-8 11375A
1. locate desired adapter size.
11875 1-718 11875A
Over-The-Spindle Adapter L
I -_ _ _ _ _ _- - - '
(Stub Model)
SERIES SIZE PART NUMBER
INCHES
10750 :¥4 10750SA
10875 718 l0875SA
11000 1 11000sA
11063 1-111 6 11063SA
Ordering Information 11375 1-3-8 11375SA
1. locate desired adapter size. 11875 1-718 11875SA
Adapter Nut and Lockscrew I,--_ _ _ _ __

SERIES SIZE PART NUMBER SERIES SIZE PART NUMBER
INCHES INCHES
10500 112 10500N 10500 112 l0500L
10625 &8 10625N 10625 &8 l0625L
10750 :¥4 10750N 10750 :¥4 10750L
10875 718 10875N 10875 718 10875L
11000 1 ll000N 11000 1 11000L
11063 1-111 6 11063N 11063 1-111 6 11063L
Ordering Information 11375 1-3-8 11375N Ordering Information 11375 1-3-8 11375L
1. locate desired adapter size. 1. locate desired adapter size.
11875 1-718 11875N 11875 1-718 11875L
2. Order by Part Number. 2. Order by Part Number.
Toolholder Seal and Snap Ring , - I_ _ _ _- - - - '
SERIES PART SERIES PART

NUMBER NUMBER
NOTE:
10750 107~TS 10750 3002-TSR Snap rings are
Ordering Information 11063 11063-TS Ordering Information 11063 4002-TSR manufactured
1. locate desired Series number 1. locate desired Series number by Spir%x
11375 4002-TS 11375 4002-TSR
2. Order by Part Number listed 2. Order by Part Number listed Company.
______________________________________________________________________________ 5
FL-Tool Holders'"
Straight Shank Toolholder Assembly

NOTE: Toolholder assembly includes body,
collet, collet nut, snap ring, positive drive,
pre-set screw assembly, face seal and snap
ring. For thru-coolant applications a rear
coolant seal and rubber washer are re-
quired.
F
SERIES A B C D F G
HOLDER TOOL SIZE TOOL SIZE E
SHANK -INCHES ~ MIN. MAX.
10750 314 .0625-.4375 1.5875-11 .1120 1.65 1.75 1.50 3.62 1.44 112--32
11063 1-1116 .1094-.7500 2.7788-19.0500 2 .00 2.18 2.30 5.24 2.02 13'16- 20
11375 1-3-8 .1094-.7500 2.7788-19.0500 1.70 1.88 2.30 4.80 2.02 13'16-20
SERIES TOOL SIZE TOOL SIZE PART NUMBER

-INCHES ~ Ordering Information (With Collet)
.0625-.1249 1.5875--3.1725 10750-SS-000 To order a complete toolholder assembly (with collet), you
must have the following information :
.1250-.1874 3.1750-4.7600 10750-5S-001
1. Series to be used,
.1875-.2499 4 . 7625~ . 3475 10750-5S-002 2. Positive drive size (see tables above using tool size to de-
10750 termine Part Number).
.2500-.3124 6.3500-7.9350 10750-55-003
3. Specify English (E) or Metric (M).
.3125-.3749 7.9375-9.5225 10750-55-004 4. Tool shank size for collet I.D.-4 place decimal.
.3750-.4375 9.5250-11 .1120 10750-S5-o05 (See page 8 for collet ordering information .)
11063-55-000 5. Specify K if thru-coolant application is required.
.1094-.1249 2.7788--3.1725
11375-S5-o00
11063-SS-001
EXAMPLE:
.1250-. 1874 3.1750-4.7600
11375-SS-001 -55-00 - - -K
-~- -~-~-~ ~
11063-55-002
.1875- .2499 4 . 7625~ . 3475 (1) (2)(3) (4) (5)
11375-55-002
11063-S5-o03
.2500-.3124 6.3500-7.9350
11375-SS-003 Ordering Information (Without Collet)
11063
To order a complete tool holder assembly (without collet),
11 063-5S-004
OR .3125-.3749 7.9375-9.5225
11375-5S-004
you must have the following information :
1. Series to be used .
11375 11063-55-005
.3750-.4687 9.5250-11 .9050 2. Positive drive size (see tables above using tool size to de-
11375-5S-005
termine Part Number).
11 063-5S-006
.4688-.5624 11 .9075-14.2850
11375-55-006 EXAMPLE:
.5625-.6561 14.2875-16.6649
11063-S5-007 _---,__-55-00
11375-S5-007
~ ~
11063-S5-o08 (1) (2)
.6562-.7500 16.6675-19.0500
11375-5S-008
NOTE: Tang drives are recommended for all tools.
6 _________________________________________________________________________
Straight Shank, Collet Type Toolholders and Over- The-Spindle Adapters
Individual Components
SPINDLE OVER-THE- STRAIGHT SHANK TOOLHOLDER COLLET COLLET
(Page 12) SPINDLE TOOLHOLDER SNAP RING (Page 10) SNAP RING
ADAPTER (This page) (Page 5) (Page 10)
(Page 5)
LOCK POSITIVE DRIVE & TOOLHOLDER RUBBER WASHER COLLET

SCREW PRE-SET SCREW SEAL - THRU-COOLANT NUT
(Page 5) ASSEMBLY (Page 5) ONLY (Page 10)
(Page 11 ) (Page 10)
NOTE: Toolholder assembly is retained in
the spindle by a FL-Tool Holders Quick-
Change over-the-spindle adapter.
NOTE: All straight shank components are
interchangeable with tapered toolhold-
ers except for the positive drive and set
screw assembly for Part Number 10750.
NOTE: For Thru-coolant applications, a
rubber washer (page 10) and rear coolant
seal (page 11) are required.
Straight Shank Toolholder BO~Y II-_ _ __
~-------- A- - - - - - - - - . j
E
DIA. 1 - - - - - B ---.j
D- ACME THREAD (LEFT HAND)

~ C-ACME THREAD
SERIES SHANK A B C 0 E
SIZE PART
~NCHES NUMBER
Ordering Information 10750 314 1075~558 4.00 1.50 1-124G 1-3-8-12 .75001.7499
1. Locate desired Series Number.
11063 1-1116 11063-558 4.92 1.80 l -V2- 124G 1-314-12 1.0626/1 .0625
11375 1-3-8 11375-558 5.52 1.50 1-V2-124G 2- 12 1.3751 /1.3750
_________________________________________________________________________ 7
FL-Tool Holders™
Collet Type Toolholder Assembly

NOTE: Toolholder assembly includes
body, collet, collet nut, snap ring,
E positive drive pre-set screw assembly,
~---- TOOL SET RANGE -----,~
COOLANT PLUG MAX. DIM .) adjuster nut, face seal and snap ring.
For thru-coolant applications a rear
coolant seal and rubber washer are
G
required.
F
SERIES A-TOOL C 0 F G
SIZE B-TOOLSIZE B-TOOLSIZE E
~NCHES ~NCHES -MM MAX.
10750 314 .0625-.4375 1.5875-1 1.1120 1.68 1.78 1.50 3.70 1.44 112-32
11063 1-V16 .1094-.7500 2.7788-19.0500 2.06 2.24 2.30 4.56 2.02 13116-20
11375 1-36 .1094- .7500 2.7788-1 9.0500 1.68 1.86 2.30 5.20 2.02 13116-20
SERIES TOOL SIZE TOOL SIZE PART NUMBER

Ordering Information (With Collet)
~NCHES -MM To order a complete toolholder assembly (with collet), you
.0625-.1249 1.5875-3.1725 107SD-OH-OOO must have the following information:
.1250-.1874 3.1750--4.7600 1075D-OH-D01
1. Series to be used .
2. Positive drive size (see tables above using tool size to de-
.1875-.2499 4 . 7625~. 3475 1075D-OH-D02 termine Part Number).
10750
.2500-.3124 6.3500-7.9350 1075D-OH-003 3. Specify English (E) or Metric (M).
4. Tool shank size for collet I.D.-4 place decimal.
.3125-.3749 7.9375-9.5225 107SD-OH-004
(See page 8 for collet ordering information.)
.3750-.4375 9.5250-11.1120 1075D-OH-DOS 5. Specify K if thru-coolant application is required .
11063-0H-OOO
.1094-.1249 2.7788-3.1725
11375-0H-OOO EXAMPLE:
.1250-.1874 3.1750--4.7600
1',~-_ --.11 -DH-OO _ - _ - _ _-K
11375-0H-D01
~ ~ ~ ~ ~
1',_y-_ ~ .•_
.1875-.2499 4 . 7625~ . 3475
(1) (2) (3) (4) (5)
11375-0H-D02
11063-0H-003
.2500-.3124 6.3500-7.9350 Ordering Information (Without Collet)
11063 11375-0H-003
11063-0H-004 To order a complete toolholder assembly (without collet),
OR .3125-.3749 7.9375-9.5225 you must have the following information:
11375-0H-004
11375 11063-0H-005 1. Series to be used .
.3750-.4687 9.5250-11 .9050 2. Positive drive size (see tables above using tool size to de-
11375-0H-005
11063-DH-D06 termine Part Number) .
.4688-.5624 11 .9075-14.2850
11375-0H-D06
111 7 EXAMPLE:
.5625-.6561 14.2875-16.6649
11375-0H-D07 _ _ _ -DH-OO
11063-DH-008 ~ ~
.6562-.7500 16.6675-19.0500
11375-0H-008 (1) (2)
8 ______________________________________________________________________________
Individual Components
SPINDLE OVER-THE- TOOLHOLDER STRAIGHT SHANK COLLET COLLET
(Page 12) SPINDLE SNAP RING TOOLHOLDER (Page 10) SNAP RING
ADAPTER (Page 5) (This page) (Page 10)
( 5)
ADAPTER NUT
(Page 5)
LOCK TOOLHOLDER POSITIVE DRIVE & RUBBER WASHER COLLET

SCREW SEAL PRE-SET SCREW - THRU-COOLANT NUT
(Page 5) (Page 5) ASSEMBLY ONLY (Page 10)
(Page 11) (Page 10)
NOTE: Toolholder assembly is retained
in the spindle by a FL-Tool Holders
Quick-Change over-the-spindle
adapter.
NOTE: All straight shank components
are interchangeable with tapered
toolholders except for the positive
drive and set screw assembly for Part
Number 10750.
NOTE: For Thru-coolant applications, a
rubber washer (page 10) and rear
coolant seal (page 11) are required.
Collet Type Toolholder Body IL--_ _ _ _---'
D-ACME THREAD (LEFT HAND) ~ ~ C- ACME THREAD
SHANK PART
SERIES SIZE- A B C 0
NUMBER
INCHES
10750 314 10750-DHB 3.81 1.00 1- 124G 314-12

Ordering Information 11063 1-1 /16 11063-DHB 4.88 1.38 1-1;2-124G 1-1/1 6- 12
1. locate desired Series Number.
11375 1-3-8 11375-DHB 5.38 1.00 1-1;2-124G 1-3-8--12
_________________________________________________________________________ 9
FL-Tool Holders'"
Collet
TOOL SIZE
RANGE
o
SNAP RING
REFERENCE
2. Specify English (E) or Metric (M) .
3. Determine proper collet I.D. size, use NOTE: These are precision collets manufactured within ±.0001
C inch of specified tool shank size. FL-Tool Holders recommends a
the high limit on the tool shank. GAGE
4. Add K at end of Part Number if thru- +.0000/-.0005 inch tolerance on tool shank to ensure maximum
DIAMETER accuracy and clamping performance (up to -.0015 inch tolerance
coolant is required (a rubber washer
will be supplied). is acceptable if necessary). Shank taper should not exceed .0002
inch.
EXAMPLE: Series 11375 collet used
A·TOOLSIZE A·TOOLSIZE
with a .7500 +.0000/-.0005 diameter SERIES PART NUMBER
-INCHES -MM B C
tool shank requires collet part number
4000-El500. 10750 3002--£IM (I<) .1094-.5000 2.7788-12.7000 1.185 .7200
A snap ring is supplied with each collet 11063 or 11375 4002--£IM (I<) .1094-.7500 2.7788-19.0500 1.770 1. 1310
item ordered.
Collet Nut and Snap Ring L

I . . -_ _ _ _ _ _- - - - '
1
O.~Lr
+
o
B
MINIMUM
CLEARANCE
DIAMETER
D
WRENCH t
SIZE / I
C
THREAD SIZE
/\
--
SERIES PART NUMBER A B C 0 SERIES PART NUMBER
10750 3002-N .644 1.44 1- 12 1·V4 Ordering Information 10750 3002-5R
11063 or 11375
4002-N .696 2.02 1·112-12 1':314 11063 or 11375 4002-5R
RubberVVasher ~
1 ____________________~
o
PART NUMBER
RW-1
~
A·TOOLSIZE
-INCHES
.180-.220
.220-.260
.260-.300
.300-.340
A·TOOLSIZE
-MM
4.57-5.60
5 . 6~ . 60
6.60-7.60
7 .6Q-8.60
PART NUMBER
RW~
RW---e
RW-10
RW-11
A·TOOLSIZE
-INCHES
.500-.540
.540-.580
.580- .620
.620-.660
A·TOOLSIZE
-MM
12.70-13.70
13.70-14.70
14.70-15.70
15.70- 16.80
2. Use Tool Shank size to determine
RW-4 .340-.380 8.60-9.60 RW-12 .660-.700 16.80-17.80
Part Number.
SERIES PART NUMBER RW-6 .380- .420 9.60- 10.60 RW-13 .700-.740 17.80-18.80
10750 3002-RW_ RW-6 .420-.460 10.60-11 .70 RW-14 .740-.780 18.80-19.80

11063 or 11375 4002-RW_ RW-7 .460-.500 11 .70-12.70
10 ____________________________________________________________________________
Positive Drive and Pre-Set Screw Assembly

E
HEX FOR
ALLEN WRENCH r~~ ~
SCREW DRIVER A
SLOT REF. LEFT HAND
THREAD
Ordering Information A-TOOL SIZE A-TOOL SIZE A B C 0 E TANG WIDTH

SERIES PART NUMBER -INCHES -NM REFERENCE
2. Use Tool Shank size to deter- 1075G-O .0625-.1249 1.5875-3.1725 NO SLOT 3'16 - --
mine Part Number. 10750-1 .1250- .1874 3.1750-4.7600 .096 .18 3'16 .094- .090
10750-2 .1875-.2499 4 . 7625~ . 3475 .125 .18 3'16 .122- .118
10750 112-32 .70
10750-3 .2500-.3124 6.3500-7.9350 .172 .22 3'16 .162- .158
10750-4 .3125-.3749 7 .9375-9.5250 .213 .22 3'16 .203-.199
10750-5 .3750-.4375 9.5250-11 .1120 .253 .25 3'16 .243-.239

4OO2---{) .0625- .1249 1.5875-3.1725 NO SLOT 5116 ---
4002-1 .1250-.1874 3.1750-4.7600 .096 .25 5116 .094- .090
4002-2 .1875-.2499 4 . 7625~ . 3475 .125 .25 5116 .122- .118

11063 4002-3 .2500-.3124 6.3500-7.9350 .172 .31 5116 .162- .158
OR 4002-4 .3125-.3749 7.9375-9.5225 13'16- 20 .88 .213 .31 5116 .203- .199
11375 4002-5 .3750- .4686 9.5250- 12.4104 .253 .31 5116 .243-.239
4oo2~ .4687-.5624 12.4130-14.2850 .313 .31 5116 .303- .297
4002-7 .5625-.6561 14.2875-16.6649 .383 .31 5116 .373-.367

4002-8 .6562-.7500 16.6675-19.0500 .453 .31 5116 .443- .437
Rear Coolant Seals L

I - -_ _ _ _ _ _ _ _ _- - - - '
ORING
GROOVE REF.
o
COOLANT
HOLE A PLUG 0 .0.
B SPINDLE 1.0.
t SERIES PART ±O.OO5 A +0.002 C 0

C NUMBER ~.OOOB
Ordering Information 10750 10750-RCS .740 .750 1/2-32 .31

11063 11063-RCS .740 .750 13/16- 20 .50
2. Use Tool Shank size to determine
Part Number. 11375 11375-RCS .990 1.000 13/16-20 .50
Note: a ring supplied with plugs
11
FL-Tool Holders'"
FACE MUST BE SQUARE --,--_
Recommended M
WITH BORE WITHIN 0.0002 T.I.R. 90.
~\ L* P DRILL G
Spindle ~~K~~ 30.l
Dimensions ~I - A* E -- - --
~dJ
NOTE: Diameters marked
with an asterisk (*) must be
concentric within.ODDS T.I.R. (Long O.S.A.)
1------- H
J
..IUNI03 ..0.005 +0.005 ..0.000 +0.000 ..0.002 .. 0.000

SERIES E G H J K -G.OOO L
M
-G.OOS N
P
-G.OOOO A -G.OOO B -G.OOO C -G.DOS D -G.002 F
10750 .7503 .162 .830 1.250 .81 1.235 2.50 2.62 3.62 .81 .750 .78 .500 .250
11063 1.0629 .193 1.158 1.562 1.12 1.610 3.12 3.25 4.25 1.12 .750 .78 .500 .312
11375 1.3754 .256 1.499 1.812 1.44 1.985 4.12 4.25 5.25 1.44 1.000 1.03 .500 .375
Socket Spindle Collar Wrench 1 ' - - - - - - - - - - '

PART A B
A B
·1 SERIES
10500
NUMBER
l0500-W
DIAMETER
1.38
LENGTH
4.00
10625 l0625-W 1.62 4.50
10750 1075G-W 1.88 4.50
10875 10875-W 2.00 4.50
11000 11~W 2.12 4.50
NOTE: It is recommended 11063 11063-W 2.23 4.50

Ordering Information that this wrench be used to
1. Locate desired Series Number. loosen or tighten the 11375 11375-W 2.62 4.50
2. Order by Part Number. spindle collar.
11875 11875-W 3.25 4.50
Open End Spindle Collar Wrench L - - I_ _ _- - - '
~B
j SERIES PART NUMBER
A B
A~J
DIM. DIM.
10750 2002-WSP 7.81 1.54

11063 l1063-WSP 8.62 1.91
11375 4002-WSP 8.62 2.28
1 1 + - - - - - - - . . .-
NOTE: It is recommended
that this wrench be used to
Ordering Information loosen or tighten the
1. Locate desired Series Number. spindle collar.
A Member of the 36010 Industrial Road

Air Gage Family of Companies Livonia , Michigan 48150
Telephone 313/591-0134
One Step Ahead in Quality Control
FAX 313-591 -7866
12 __________________________________________________________________________
AGC-311/94 LITHO IN USA
FL-TOOL HOLDERS
3601 0 Industrial Road • Livonia, Michigan 48150
Phone: 734-591-0134· Fax: 734-591-7866
3/4" STRAIGHT SHANK TOOL HOLDERS

WITH ER 16 COLLET NUT SYSTEM
• Increased Machining Efficiency
• High Accuracy Repeatability
• Quick Changeability
• Thru Coolant Capability
• Patented
Straight shank tool holders can be used in existing Clockwise direction to mate with the Acme left-
automotive spindles with over-the-spindle adapters hand thread on the tool holder body, retaining the
to transform any spindle, regardless of original holder securely against the spindle face, This
manufacturer, into a quick-change design, Bene- eliminates the rocking condition seen is short taper
fits of the system include increased machining effi- designs, Counterclockwise rotation of the collar
ciency, high accuracy repeatability and quick- forces the tool holder body out of the spindle ,
change ability,
Each patented tool holder assembly features a
The 3/4" body size will accommodate tools rang- straight shank with an 1.0, tapered collet seat that
ing from 1/16" (1 ,588 mm) to 7/16" (11 ,112 mm) in accurately locates the cutting tool centerline and
diameter, Straight shank tool holders feature a an adjustable preset screw and drive assembly
guaranteed accuracy within 0,0001 T,I.R , runout which provides tool height adjustment and positive
two inches from the collet face , This is measured drive to the tool. A sealed collet and rear coolant
by a zero spindle and a class XX gage pin , seal for thru-coolant applications are available,
,The compact design minimizes spindle to spindle
The close fit of the tool holder 0.0, to the spindle I. center distance and overhang from the spindle
D, enables accurate and secure positioning of the end to the bearing journal diameters ,
over-the-spindle adapter collar , Mounted over an
existing spindle, the collar is rotated in a
STRAIGHT SHANK TOOL HOLDER WITH ER 16 COLLET NUT SYSTEM
1.60 MIN.
-----f-NOTE: SUBTRACT .50 ON
3.20 MAX.
THE MAX. toOL
AOJUSTMENT IF A
f - - - - 1.9 1
COOLANT PLUG 'is
(STANDARD) USED.
~r
1.20
(STUB)
1.01
AOAPTER ASSEMBLY REF.
STANDARD PT.# 107S0-A
STUB PT# 10750-SA
-.--- -----
+ .000
-.002
1.10 DIA.RET.
1.235 DI A.
SPINDLE REF.
LOCKSCREW _ ~SPINDLE
5/16-24 UNF ~ END REF.
PT.# 10750-L
INCLUDED IN ASS 'Y 1.25 1.80
(STA NDARD)
ASSEMBLY ORDERING OPTIONS

ASSEMBL Y WITH
SHANK TOOL SHANK ASSEMBLY ASSEMBLY REAR
BODY & COLLET OSA
DIAMETER RANGE WITH COLLET LESS COLLET COOLANT SEAL
NUT
.0625-.1249 10750·ER·000·EIMXXXX 10750·ER·000
.1250-.1874 10750·ER·001 ·EIMXXXX 10750·ER·00 1

10750·A
.1875-.2499 10750·ER·002·EIMXXXX 10750·ER·002 (STANDARD)
314 10750·ERBN OR 10750·RCS
.2500-.3124 10750·ER·003·EIMXXXX 10750·ER·003 10750·SA
(STUB)
.3125-.3749 10750·ER·004·EIMXXXX 10750·ER·004
.3750-.4375 10750·ER·005·EIMXXXX 10750·ER·005
INDIVIDUAL COMPONENT ORDERING OPTIONS

SHANK TOOL SHANK TOOL HOLDER REAR
POSITIVE DRIVE COLLET NUT OSA
DIAMETER RANGE BODY COOLANT SEAL
.0625-. 1249 10750·0
.1250-.1874 10750·1
10750·A
.1875-.2499 10750·2 (STANDARD)
314 10750·ERB SA·20·5A OR 10750·RCS
.2500-.3124 10750·3 10750·SA
(STUB)
.3125-.3749 10750·4
.3750-.4375 10750·5
Thru-coolant applications require a rear coolant seal (-RCS) and sealed collet (-S) (order separately)
Tool holders must be used with the FL-Tool Holder (OSA) Over-the Spindle Adapter (order separately)
Unless ordered with complete assembly, collets must be ordered separately (see collet dat sheet)
Full scale drawing templates are available for assistance in tool layouts, alterations or new designs,
Cad disk available upon request.
FL-TOOL HOLDERS
3601 0 Industrial Road • Livonia, Michigan 481 50
Phone: 734-591-0134· Fax: 734-591-7866
1 3/8" STRAIGHT SHANK TOOL HOLDERS

• Patented
to transform any spindle, regardless of original holder sec urely against the spindle face . This
manufacturer, into a quick-change design. Bene- eliminates the rocking condition seen is short taper
fits of the system include increased machining effi- designs . Counte rclockwise rotation of the coliar
ciency, high accuracy repeatability and quick- forces the tool holder body out of the spindle .
change ability.
Eac h patented tool holder assembly features a
The 1 3/8" body size will accommodate tools rang - straight shank with an 1.0. tapered collet seat that
ing from 7/64" (2.778 mm) to 3/4" (19.05 mm) in accurately locates the c utting tool cente rline and
diameter. Straight shank tool holders feature a an adjustable preset screw and drive assembly
guaranteed accuracy within 0.0001 T.I .R. runout which provides tool height adjustment and positive
two inches from the collet face. This is measured drive to the tool. A sealed collet and rear coolant
by a zero spindle and a class XX gage pin . seal for thru-coolant applications are available .
. The compact design minimizes spindle to spindle
The close fit of the tool holder 0.0 . to the spindle I. center distance and overhang from the spindle
D. enables accurate and secure positioning of the end to the bearing journal diameters.
over-the-spindle adapter collar. Mounted over an
2. 12 MIN.
- - - - - t - N O T E ; SUBTRACT .50 ON
4.70 MAX.
THE MAX. TOOL
ADJUSTMEN T IF A
- - 2.47 COOLA NT PLUG IS
(STANDARD)
USED.
ADAP TER ASSEMBL Y

STA NDARD PT.# l1J 75-A .38
STUB PT# l 1J75-SA REF.
+.000
-. 002 ·
1.97 DIA.REF.
1.985 DIA.
SPINDLE REF.
-L--_ - - - - - - -:s~===~~t:5r-E::::: + - - - - ' -

LOCKSCRE W _ ~SPINDLE
5/16-2 4 UNF ~ END REF.
PT.# 1I 375~L
INCLUDED IN ASS'Y 1.810 1.75
(STANDARD)

ASSEMBLY WITH
BODY & OSA
COLLET NUT
.1094-.1249 11375·ER·000·E/MXXXX 11375·ER·000

.1250-.1874 11375·ER·00 l·E/MXXXX 11375·ER·00 1
.1875-.2499 11375·ER·002·E/MXXXX 11375·ER·002
11375·A
.2500-.3124 11375·ER·003·E/MXXXX 11375·ER·003 (STANDARD)
1·3/8 .3125- .3749 11375·ER·00H/MXXXX 11375·ER·004 11375·ERBN OR 11375·RCS
11375·SA
.3750- .4687 11375·ER·005·E/MXXXX 11375·ER·005
(STUB)
.4688-.5624 11375·ER·006·E/MXXXX 11375·ER·006
.5625-.6561 11375·ER·007 ·E/MXXXX 11375·ER·007
.6562-.7500 11375·ER·008·E/MXXXX 11375·ER·008

.1094- .1249 4002·0

.1250 - .1874 4002·1
.1875-.2499 4002·2
11375·A
.2500- .3124 4002·3 (STANDARD)
1·3/8 .3125- .3749 4002-4 11375·ERB SA·32·5A OR 11375·RCS
11375·SA
.3750-.4687 4002·5
(STUB)
.4688- .5624 4002·6
.5625-.6561 4002·7
.6562-.7500 4002·8
Full scale drawing templates are available for assistance in tool layouts, alterations or new designs ,
FL-TOOL HOLDERS
3601 0 Industrial Road • Livonia, Michigan 48150
Phone : 734-591 -0134 · Fax: 734-591-7866
www.fltoolholders .com
1 1/16" STRAIGHT SHANK TOOL HOLDERS

• Patented
to transform any spindle, rega rd less of orig inal holder sec urely aga inst the spindle face. This
manufacturer, into a quick-change design. Bene- e limina tes the rocking condition seen is short taper
fits of the system include increased machining effi- designs. Counterc lockwise rota tion of the collar
ciency, high accu racy repeatability and quick- forces the tool holder body o ut of the spindle.
c hange ability.
Eac h patented tool holder a ssembly features a
The 1 1/l 6" body size wi ll accommodate tools stra ight sha nk with an 1.0. ta pe red collet seat that
ranging from 7/64" (2 .788 mm) to 3/4" (19.05 mm) acc urately locates the c utting tool centerli ne and
in diameter . Straight shank tool holders feature a an adjustable preset screw a nd drive assembly
guaranteed acc urac y within 0.000 1 T.I.R. runout whic h p rovi des tool height adjustment a nd positive
two inches from the collet face . This is measured d rive to the tool. A sealed collet and rear coolant
by a zero spindle and a c lass XX gage pin . seal for thru-coolant applications are avai lable .
The compact design minim izes spindle to spindle
The close fit of the tool holder 0.0 . to the spindle I. cente r distance and overha ng from the spindle
D. enables ac curate and secure positioning of the end to the bearing journa l diameters.
over-the-spindle adapter collar. Mounted over an
2. 12 MIN .
- - --t-NOT[: SUBTRA CT .50 ON
3.70 MA X. TH[ MAX. TOOL
ADJUSTM[NT IF A
f--- 2.22 COOLANT PLUG IS
(STANDARD) USED.
~r
1. 20
(STUB)
1.01
ADAPT[R ASS[MBLY RET
.2362 MIN. _
STANDARD PT. # 11063- A .38 . 7500 MAX.
STUB PT# II 063 -SA R[F. TOOL RANG[
+ .000
-.002 .
I.6 10DIA
SPINDL[ R[F.
LOCKSCR[W _ ~ SP I NDL[
5/16 - 2 4 UNF ~ [NO R[F..
PT.# 11 063 - L
INCLUDED IN ASS'Y 1. 56 1.75
(S TANDARD)

ASSEMBLY WITH
BODY & oSA
COLLET NUT
.1094-. 1249 11063·ER·000·E/MXXXX 11063·ER·000

.1250 -.1874 11063·ER·001 ·E/MXXXX 11063·ER·001
.1875-.2499 11063·ER·002·E/MXXXX 11063·ER·002
11063·A
.2500- .3124 11063·ER·003·E/MXXXX 11063·ER·003 (STANDARD)
1·1/16 .3125-.3749 11063·ER·004·E/MXXXX 11063·ER·004 11063·ERBN OR 11063·RCS
11063-SA
.3750- .4687 11063·ER·005·E/MXXXX 11063·ER·005
(STUB)
.4688-.5624 11063·ER·006·E/MXXXX 11063·ER·006
.5625-.6561 11063·ER·007·E/MXXXX 11063·ER·007
.6562-.7500 11063·ER·008·E/MXXXX 11063·ER·008

POSITIVE DRIVE COLLET NUT oSA
.1094-.1249 4002·0
.1250 -. 1874 4002·1
.1875-.2499 4002·2
11063·A
.2500- .3124 4002·3
(STANDARO)
1·1/16 .3125-.3749 4002·4 11063·ERB SA·32·5A OR 11063·RCS
11063·SA
.3750-.4687 4002·5 (STUB)
.4688-.5624 4002·6
.5625- .6561 4002·7
.6562-.7500 4002·8
Full scale drawing templates are available for assistance in tool layouts, alterations or new designs.
Cad disk available upon request .
FL-TOOL HOLDERS
Phone: 734-591-0134· Fax: 734-591-7866
'N'NW. fltoolholders.com
1 1/1 6" STRAIGHT SHANK TOOL HOLDERS

• Patented
to transform any spindle, regardless of original holder securely against the spindle face , This
manufacturer, into a quick-change design , Bene- eliminates the rocking condition seen is short taper
fits of the system include increased machining effi- designs, Counterclockwise rotation of the collar
ciency, high accuracy repeatability and quick- forces the tool holder body out of the spindle,
change ability,
Each patented tool holder assembly features a
The 1 1/16" body size will accommodate tools straight shank with an 1.0, tapered collet seat that
ranging from 7/64" (2.788 mm) to 3/8" (9 ,525 mm) accurately locates the cutting tool centerline and
in diameter, Straight shank tool holders feature a an adjustable preset screw and drive assembly
guaranteed accuracy within 0,0001 T,I.R , runout which provides tool height adjustment and positive
two inches from the collet face , This is measured drive to the tool , A sealed collet and rear coolant
by a zero spindle and a class XX gage pin, seal for thru-coolant applications are available ,
The compact design minimizes spindle to spindle
The close fit of the tool holder 0.0, to the spindle I. center distance and overhang from the spindle
D, enables accurate and secure positioning of the end to the bearing journal diameters ,
over-the-spindle adapter collar , Mounted over an
1.60 MIN .
- - - - t - N O T f : SUBTRACT .50 ON
3 .80 MAX.
THE MAX. TOOL
ADJUSTMENT IF A
1 - - - - 2.22
COOLANT PLUG IS
(STANDARD)
USED.
1.20
(STUB)
- 1.0 1
ADAPTER ASSEMBLY REF.
STANDARD prj 11 0 63- A 4.000 mm MIN.
.38 9.525 mm MA X.
STUB P T# 11 0 63-SA REF. TOOL RANGE
-,---- - ----
+ .000
-. 002
1.610 DIA .
SPINDLE REF.
- - L . . - - -_ ___ _ _ _ ~===~~
LOCKSCREW _ ~ SPINDLE
5/ 16 - 24 UNF ~ END REF.
prj 11063 - L
INCLUDED IN ASS'Y 1.56 - - - - - 1.80
( STANDARD)

ASSEMBt. Y WITH
BOOY & OSA
COLLET NUT
.1094-.1249 11063·ER·000·E/MXXXX 11063·ER·000

11063·A
.1250 -. 1874 11 063·ER·00 l ·E/MXXXX 11063·ER·001 (STANDARD)
1·1/16 .1875-.2499 11063·ER·002·E/MXXXX 11063·ER·002 11063·ERBN OR 11063·RCS
11063·SA
.2500-.3124 11063·ER·003·E/MXXXX 11063·ER·003
(STUB)
.3125-.3750 11063·ER·00H/MXXXX 11063·ER·004

.1094- .1249 4002·0

11063·A
.1250-.1874 4002·1 (STANDARD)
1·1/16 .1875-.2499 4002·2 11063·ERB SA·32·5A OR 11063·RCS
11063·SA
.2500-.3124 4002·3
(STUB)
.3125-.3750 4002·4
Full scale drawing templates are available for assistance in tool layouts, alterations or new designs,
FL-Yap and Reamer Holders Increase
Positioning Accuracy to Improve Quality
FL floating tool holders Our standard 'line of tap
are designed and built to Features and Benefits
reamer holding
compensate for components include tap
• Automatically compensates
misalignment between the adapters,SA collets, tap
for misalignment
spindle and work piece on collets, reamer collets,
• Armorclad surface coating
previous drilled holes. Morse taper and dedicated for corrosion resistance
Our standard holders size. Each component • Coolant thru available
feature various styles of within our holders is • Close Center distance
shanks including acme engineered and • Adjustable tension and self
threaded, straight, Morse manufactured to ensure centering
taper and Cat "V". Special maximum wear and • Collet system and quick
designs can also be durability. change
manufactured to satisfy • Specials and custom design
your spindle requirements. available
• Repair Facility on premises
FL-Tool Holders
I Table of Contents I
TAR Series Quick Change Non-Floating Acme TAEA Series Quick Change Tap Adapters Axial
Shank Tap Holders - - - - - - - - - - - - - - - - - - - - - Page 3 Length Adjustment-Extended - - - - - - - - - - - - - Page 14
TAR Series Quick Change Non-Floating Straight DSA Series Quick Change Dedicated Size Radial
Shank Tap Holders - - - - - - - - - - - - - - - - - - - Page 3 Floating Acme Shank Tap Holders - - - -- - - - - Pages 15-20
TAR Series Quick Change Non-Floating Morse SM Series Collet Type Radial Floating Acme
Taper Shank Tap Holders - - - - - - - - - - - - - - - Page 4 Shank Reamer Holders - - - - - - - - - - - - - - - - - Page 21
TATC Series Quick Change Non-Floating Straight SM Series Collet Type Radial Floating Straight
Shank Tension and Compression Tap Holders - -Page 4 Shank Reamer Holders - - - - - - - - - - - - - - - - - Page 22
TM Series Quick Change Radial Floating Acme SAC Series Collet Type Radial Floating Cat "V"
Shank Tap Holders - - - - - - - - - - - - - - - - - - - - Page 5 Flange Reamer Holders - - - - - - - - - - - - - - - - Page 22
TAS Series Quick Change Radial Floating Straight SA 16 Series Single Angle Collets - - - - - - - - - Page 23
Shank Tap Holders - - - - - - - - - - - - - - - - - - - - Page 5
SA 20 Series Single Angle Collets - - - - - - - - - . Page 23
TAM Series Quick Change Radial Floating Morse
Taper Shank Tap Holders - - - - - - - - - - - - - - - - - Page 6 SA 25 Series Single Angle Collets - - - - - - - - - - Page 24
TATC Series Quick Change Radial Floating Acme SA 32 Series Single Angle Collets - - - - - - - - - Page 24
Shank Tension-Compression Tap Holders - - - Page 7
SAX Series Tap Collets with Internal Square Drive-Page 25
TATC Series Quick Change Radial Floating Straight
Shank Tension-Compression Tap Holders - - - - Page 8 SA Series Single Angle Collet Accuracy and
Installation and Removal Diagram - - - - - - - Page 26
THA Series Quick Change Radial Floating Acme
Shank Tap Holders (Standard) - - - - - - - - - - - Page 9 TCA Series Collet Type Radial Floating Acme
Shank Tap and Reamer Holders - - - - - - - - - - - - Page 27
THS Series Quick Change Radial Floating Straight
Shank Tap Holders ( Standard) - - - - - - - - - - - -Page 9 TCA Series Collet Type Radial Floating Straight
Shank Tap and Reamer Holders - - - - - - - - - - - Page 28
THJ Series Quick Change Radial Floating Jacobs
Shank Tap Holders ( Standard) - - - - - - - - - - - Page 10 TC Series Tap Collets - - - - - - - - - - - - - - - - - - Page 29
CAT Series Quick Change Radial Floating Cat "V" TC Series Reamer Collet - - - - - - - - - - - - - - - - Page 29
Flange Tap Holders - - - - - - - - - - - - - - - - - - - - - Page 10
MTA Series Morse Taper Radial Floating Acme
TA & TAP Series Quick Change Fixed Length Tap Shank Tap and Reamer Holders A, B - - - - - - Page 30
Adapters - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 11
MTB Series Morse Taper Radial Floating Acme
TSA Series Quick Change Collet Type Tap Shank Tap and Reamer Holders - - - - - - - - - - Page 30
Adapters - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page 12
MTA Series Morse Taper Radial Floating Acme
TC Series Quick Change Torque Adapters - - Page 12 Shank Tap and Reamer Holders C - - - - - - - - Page 31
TALA Series Quick Change Tap Adapters Axial FL Series Adjustable Acme Nuts --------- Page 31
Length Adjustment - - - - - - - - - - - - - - - - - - - Page 13
------------------------------------------------------------------------2
PHONE: 734-591-0134 • FAX: 734-591-7866 36010 INDUSTRIAL ROAD. LIVONIA, MI 48150
FL-Tool Holders
Quick Change Non-Floating

Acme Shank Tap Holders
ORDERING INFORMATION
1. Locate desired Tap and
Holder size in table.
2. Order by Part Number

See Pages 11-14
shown.
For Tap Adapters
HOLDER TAP A L
PART NUMBER D SHANK
SIZE SIZES DIAMETER LENGTH
TAR·0·7001 5/8·16
0 0101/4 0.875 1.890 3.00
TAR·0·7002 3/4·12
TAR·l ·7005 3.00 5/8·16
TAR·l ·7006 1 010 1/2 1.250 2.043 3.00 3/4·12
TAR· l ·7009 3.625 11/16·12
TAR·2·7013 3.625 11/16·12
2 5/16107/8 1.970 2.913
TAR·2·7014 4.625 1 3/8·12
TAR·3·7018 3 13/16101 3/8 2.835 3.993 4.625 13/8·12

Straight Shank Tap Holders
rLnt,
r-
2. Order by Part Number - I A See Pages 11-14

I
u
shown . For Tap Adapters
~I-~---- D ------~I
'-- /
HOLDER TAP A L
PART NUMBER D SHANK
TAR·0·7055 1/2
0 0101/4 0.875 1.450
TAR·0·7056 3/4
4.00
TAR·l ·7057 3/4
1 010 1/2 1.250 1.650
TAR·l·7058 1
TAR·2·7060 4.00 1
2 5/16107/8 1.970 2.475
TAR·2·7061 5.00 1 1/2
TAR·3·7062 3 13/161013/8 2.835 3.555 5.00 2
3---------------------------------------------------------------------------------
Floating Tap and Reamer

Morse Taper Shank Tap Holders
See Pages 11-14
2. Order by Part Number For Tap Adapters
shown .
HOLDER TAP A L MORSE TAPER

PART NUMBER
SIZE SIZES DIAMETER LENGTH SHANK
TAR·0·7021 1.575 lMT

TAR·0·7022
#0 oto 1/4 0.875
1.637 2MT
TAR·l ·7031 1.730 1MT

TAR·l·7032 #1 oto 1/2 1.250 1.793 2MT
TAR·l·7033 1.793 3MT
TAR·2·7042 2.663 2MT

TAR·2·7043 #2 5/16 to 7/8 1.980 2.663 3MT
TAR·2·7044 2.723 4MT
TAR·3·7053 3.743 3MT

#3 13/16 to 1 3/8 2.835
TAR·3·7054 3.805 4MT
Quick Change Non-Floating Straight

Shank Tension and Compression Tap Holders
~r------ A --------~
Fie COMPRESSION T
TENSION
cC3m_~~t
2. Order by Part Number See Pages 11-14
HOLDER COMPENSATION
PART NUMBER A D E B F
SIZE Ten. Compo
TATC·1-70lO #1 3.15 1.42 0.75 0.75 1.57 0.30 0.30
TATC·2·7071 #2 4.06 2.18 1.22 0.75 1.57 0.49 0.49
TATC·l ·7072 #1 3.58 1.42 0.75 1.00 2.01 0.30 0.30
TATC·2·7073 #2 4.49 2.16 1.22 1.00 2.01 0.49 0.49
TATC·3·7074 #3 6.50 3.07 2.36 1.50 3.00 0.79 0.79
------_______________________________________________________________________ 4
PHONE: 734-591-0134 • FAX: 734-591-7866

FL-Tool Holders
Quick Change Radial Floating

Acme Shank Tap Holders
ORDERING INFORMAT ION 1= MtN. "I
g:----::-----~ [J()~~r;
Holder size in table .
See Pages 11-14
shown .
HOLDER TAP A L
PART NUMBER FLOAT 0 SHANK
TAA·O·7101 5/8·16
TAA·0·7102
0 oto 1/4 .010 .875 2.448 3.000
3/4·12
TAA·l ·7105 3.000 5/8·16

TAA·l ·7106 3.000 3/4·12
TAA·l ·7107 1 oto 1/2 .020 1.250 2.730 3.625 7/8·12
TAA·l ·7108 3.625 1·12
TAA·l ·7109 3.625 11/16·12
TAA·2·7111 3.625 7/8·12
TAA·2·7112 3.625 1·12
2 5/16 to 7/8 .040 1.980 3.863
TAA·2·7113 3.625 1 1/16·12
TAA·2·7114 4.625 13/8·12
TAA·3·7118 5.343 4.625 13/8·12
3 13/16 to 1 318 .060 2.835
TAA·3·7119 5.530 5.625 1 7/8·12

Straight Shank Tap Holders
I" L .. ,
~'--------if [I]~~ri
See Pages 11-14
~D-~"I
shown .
HOLDER TAP A L
PART NUMBER FLOAT 0 SHANK
TAS·0·7161 0 oto 1/4 .010 0.875 2.011 4.00 3/4
TAS·l·7170 3/4
TAS·l·7171
1 oto 1/2 .020 1.250 2.293 4.00
1
TAS·2·7181 4.00 1
2 5/16 to 7/8 .040 1.980 3.426
TAS·2·7184 5.00 11/2
TAS·3·7192 11/2
3 13/16 to 1 318 .060 2.835 4.906 5.00
TAS·3·7194 2
5-----------------------------------------------------------------------------

Morse Taper Shank Tap Holders

shown .
E(___ A See Pages 11 -14

For Tap Adapters
HOLDER TAP A L MORSE TAPER

PART NUMBER FLOAT
SIZE SIZES DIAMETER LENGTH SHANK
TAM·O·7121 2.136 lMT

TAM·0·7122
0 oto 1/4 .0lD .875
2.199 2MT
TAM·l ·7131 2.418 lMT

TAM·l·7132 1 oto 1/2 .020 1.250 2.481 2MT
TAM·l ·7133 2.481 3MT
TAM·2·7142 3.613 2MT

TAM·2·7143 2 5/16 to 7/8 .040 1.980 3.613 3MT
TAM·2·7144 3.671 4MT
TAM·3·7153 5.093 3MT

3 13/16 to 1 3/8 .060 2.835
TAM·3·7154 5.156 4MT
\
FL-Tool Holders Offers a Complete

Line of Complementary Products
Tapered Sha~k Tool Holders

Straight Shank Tool Holders
Hydraulic Chucks
Gun Drill and Reamer Holders
Spindles and Tool Setting Accessories
------------------------------------------------------------------6
PHONE: 734-591-0134 • FAX: 734-591-7866
FL-Tool Holders
Quick Change Radial Floating Acme

Shank (Tension-Compression) Tap Holders
L
ORDERING INFORMATION II-- - - - - - - - - MIN - - - - - - - - - 1
[[--~~ :--:BJ - ]~-

. --»--~~
A
shown .
I
HOLDER TAP A C T L
PART NUMBER FLOAT SHANK
SIZE SIZES DIAMETER COMPo TENSION LENGTH
TAC·l ·7205 5/8·16
TAC·1·7206 3/4·12
TAC·1·7207 1.170 - 6.782 7/8·12
TAC·1·7208 1·12
TAC·1·7209 11/16·12
TAC·1·7210 5/8·16
TAC·1·7211 3/4·12
TAC·1·7212 1.560 - 6.980 7/8·12
TAC·l·7213 1·12
TAC·1·7214 11/16·12
TAC·1·7215 5/8·16
TAC·l ·7216 3/4·12
TAC·1·7217 1 oto 1/2 .020 1.375 1.166 0.396 6.587 7/8·12
TAC·1·7218 1·12
TAC·1·7219 11/16·12
TATC·l ·7220 5/8·16
TATC·1·7221 3/4·12
TATC·l ·7222 0.781 0.781 6.200 7/8·12
TATC·l ·7223 1·12
TATC·l ·7224 1 1/16·12
TAT·l·7225 5/8·16
TAT·l·7226 3/4·12
TAT·1·7227 - 1.562 5.420 7/8·12
TAT·1·7228 1·12
TAT·1·7229 11/16·12
TAC·2·7230 7/8·12
TAC·2·7231 1·12
TAC·2·7232 1.090 - 7.853
11/16 · 12
TAC ·2·7233 13/8·12
TAC·2·7234 7/8·12
TAC·2·7235 1·12
TAC·2·7236 1.560 - 8.098
11/16·12
TAC·2·7237 13/8·12
TATC·2·7238 7/8·12
TATC·2·7239 1·12
2 5/16 to 7/8 .040 1.980 1.1116 0.396 7.704
TATC·2·7240 11/16·12
TATC 2·7241 13/8·12
TATC·2·7242 7/8·12
TATC·2·7243 1·12
TATC·2·7244 0.781 0.781 7.319
11/16·12
TATC·2·7245 13/8·12
TAT·2·7246 7/8·12
TAT·2·7247 1·12
TAT·2·7248 - 1.562 6.538
11/16·12
TAT·2·7250 13/8·12
7------------------------------___________________________________________________
Quick Change Radial Floating Straight

Shank (Tension-Compression) Tap Holders
11-.-------- L
MIN - - - - - - - - - - - 4 - 1
EJ _ .
shown .
-++----1 ~~------L-A
~<-------t.:------j+----*L~~~~~_---.J~I-' _---' ,
See Pages 11-14
For Tap Adapters
HOLOER TAP A C T L
PART NUMBER FLOAT SHANK
SIZE SIZES OIAMETER COMPo TENSION LENGTH
TAC·l ·7261 3/4

TAC-l ·7262 1.170 - 6.345 1
TAC ·l ·7263 11/4
TAC·l·7264 3/4
TAC·l ·7265 1.560 - 6.543 1
TAC·l·7266 1 1/4
TATC·l·7267 3/4
TATC-1-7268 1 oto 1/2 .020 1.250 1.166 0.396 6.150 1
TATC-l·7269 1 1/4
TATC·l ·7270 3/4
TATC·l·7271 0.781 0.781 5.763 1
TATC·l ·7272 11/4
TAT-1-7273 3/4
TAT-' ·7274 - 1.562 4.983 1
TAT-1-7275 1 1/4
TAC·2·7276 1
TAC-2-7277 1.090 - 7.416 1.1/4
TAC-2·7278 11/2
TAC-2·7279 1
TAC·2-7280 1.560 - 7.661 1 1/4
TAC·2·7281 1 1/2
TATC·2·7282 1
TATC·2-7283 2 5/16 to 7/8 .040 1.980 0.166 0.396 7.267 11/4
TATC-2·7284 1 1/2
TATC·2·7285 1
TATC·2·7286 0.781 0.781 6.882 1 1/4
TATC·2-7287 1 1/2
TAT·2·7288 1
TAT·2·7289 - 1.562 6.100 11/4
TAT:2-7290 1 1/2
-----------------------------------------------------------------------------8
PHONE: 734·591·0134 • FAX: 734·591·7866
FL Tool Holders

Acme Shank Tap Holders (Standard)
1. Locate desired Shank and
I'
See Pages 11 -14
shown .
~----~--~
- -~--=--=---=--C=---~--=--~-HR
-
#0 & #1 Holder size

1----- - D
02S0~ E
, -
take #1 size Tap Adapters
TAP PART HOLDER

B C D F N
SIZE NUMBER SIZE A
THA·0·7301 5/8·16 3.000

THA·0·7302 3/4·12 3.000
#0
THA·0·7303 1·12 3.625
1.500
Tap THA·0·7304 1 1/16·12 3.625
Range THA·0·7305 13/8·12 1.187 4.625 1.400 3.14
0·9/16 THA·l ·7308 3/4·12 3.000
THA·l ·7309 #1 1/12 3.625
THA·l· 7310 1.81 2 1 1/16·12 3.625
THA·l ·7311 13/8·1 2 4.625

Straight Shank Tap Holders (Standard)
ORDERING INFORMATION OP T IONAL
1. Locate desired Shank and COOLANT SE AL
2. Order by Part Number See Pages 11-14

I.
#0 & #1 Holder size
take #1 size Tap Adapters
TAP PART HOLDER

B C D F N
SIZE NUMBER SIZE A
THS·0·7401 3/4
#0
THS·0·7402 1
Tap 1.500
THS·0·7403 1 1/2
Range 1.187 4.000 1.406 2.47
0·9/16 THS·l ·7404 3/4
#1
THS·l·7405 1
1.812
THS·l ·7406 1
9---------------------------------------------------------------------------------
36010 INDUSTRIAL ROAD • LIVONIA, MI 48150

Jacobs Shank Tap Holders (Standard)
1. Locate desired Jacobs Taper
and Holder size in table.

shown.
r- --
\" DI A. Jo\COBS T ~ -
I· r-
A -
N-"h ~ I' See Pages 11-14

--
SHANK SIZ( • ..-I .984
For Tap Adapters
c~
~
L ,--t---
.I. c .1.
TAP PART HOLDER SIZE JACOB
C 0 F N
SIZE NUMBER A TAPER
THJ-1-9400 #1
THJ-2-9401 #1 #2
1.406
THJ-3-9402 1_500 #3
Tap THJ-33-9404 #33
Range 1.187 4_00 2.593
0-9/16 THJ-1-9410 #1
THJ-2-9411 #2 #2
2.200
THJ-3-9412 1.812 #3
THJ -33-9414 #33

Cat V Flange Tap Holders
1. Locate desired V Flange and "S " - V
CAT FL ANGE

shown . See Pages 11-14
For Tap Adapters
RETfNTlON KN OBS AVAILA BL E

UPO N REOUES T
ADAPTER PART HOLDER

B C E F N
SERIES NUMBER SIZE A
#1 CAT-40-1 #1 40 1.175
1.187 3_87
0-9/16 CAT-50-1 1.812 50 1_375
1_00
#2 CAT-40-2 #2 40 2.125
1.502 5_37
0-7/8 CAT-50-2 2.750 50 1.125
10
PHONE: 734-591-0134 • FAX: 734-591-7866
FL-Tool Holders
Quick Change Fixed Length Tap Adapters

L~--r-
TANG
ORDERING INFORMATION DRIVE
1. Locate desired Tap
and Adapter size in table.
=it f
2a. Order by Part Number
shown for Tang Drive.
~~ ~ I
11-*++----+-'"1" j Available in
Tang Drive or Ball Drive
2b. Add (-b) to end of Part Number
BALL ~c-~----'-
DRIVE
ADAPTER TAP A B D C L
PART NUMBER SHANK SQUARE
SIZE SIZES DIA. DIA. DIA. LENGTH LENGTH
TA·l·6 0·6 .141 .110 .85

TA·l·8 8 .168 .131 .92
TA·l ·l0 10 .194 .152 .92
TA·l ·12 12 .220 .165 .95
TA·l·l/4 14 & 1/4 .255 .191 .95
1 .73 1.18 .747 .270
TA·l·5/16 5/16 .318 .238 .98
TA·l ·7/16 7/16 .323 .242 1.08
TA·l ·l/2 1/2 .367 .275 1.11
TA·l ·3/8 3/8 .381 .286 1.05
TA·l ·9/16 9/16 .429 .322 1.17
TA·2·5/16 5/16 .318 .238 1.49

TA·2·7/16 7/16 .323 .242 1.59
TA·2·1/2 1/2 .367 .275 1.62
TA·2·3/8 3/8 .381 .286 1.56
TA·2·9/16 9/16 .429 .322 1.68
2 1.18 1.90 1.219 .310
TA·2·5/8 5/8 .480 .360 1.74
TA·2·11/16 11/16 .542 .406 1.81
TA·2·3/4 3/4 .590 .442 1.87
TA·2·13/16 13/16 .652 .489 1.87
TA·2·7/8 7/8 .697 .523 1.93
TA·3·13/16 13/16 .652 .489 2.42

TA·3·7/8 7/8 .697 .523 2.48
TA·3·15/16 15/16 .760 .570 2.48
TA·3·1 3 1 .800 .600 1.75 2.75 1.889 .405 2.54
TA·3·1·1/8 1 1/8 .896 .672 2.61
TA·3·1·1/4 11/4 1.021 .766 2.73
TA·3·1·3/8 13/8 1.108 .831 2.79
ADAPTER TAP A , B D C L
SIZE SIZES DIA. DIA. DIA. LENGTH LENGTH
TAP·l ·l/8 SSP 1/8 SSP .3125 .234 1.05

1 .73 1.18 .747 .270
TAp·l ·l/8 LSP 1/8 LSP .4375 . 32~ 1.05
TAp·2·1/8 NPT 1/8 NPT .4375 .328 1.05

TAp·2·1/4 NPT 2 1/4 NPT .5625 .421 1.18 1.90 1.219 .310 1.18
TAp·2·1/2 NPT 1/2 NPT .6875 .515 1.37
TAp·3·1/4 NPT 1/2 NPT .6875 .515 1.41

TAp·3·1/2 NPT 3/8 NPT .7000 .531 1.32
3 1.75 2.75 1.889 .405
TAp·3·3/8 NPT 3/4 NPT .9063 .812 1.55
TAp·3·3/4 NPT 1 NPT 1.125 1.68
11
Quick Change Collet Type Tap Adapters

1. Locate desired Collet series
and Adapter size in table . rA
ITc
shown . L
A B C
PART NUMBER ADAPTER SIZE COLLET SERIES TAP RANGE
(mm.) (in .) (mm.) (in.) (mm.) (in.)
TSA·16 #1 16 #0·6 - 1/2 19 0.75 25 0.98 28 1.10
TSA-25 #2 25 #0-6 - 3/4 31 1.22 34 1.34 42 1.65
TSA-32 #3 32 #0-6 - 15/16 48 1.89 48 1.89 50 1.97
Quick Change Torque Adapters

1. Locate desired Tap
and Adapter size in table.

shown .
PIPE TAP
A SIZE #1 SIZE #2 A SIZE #1 SIZE#2 A SIZE #1 SIZE #2
TAP SIZE PART # PART # TAP SIZE PART# PART # TAP SIZE PART # PART #
0- 6 TC-1 -6 TC-2-6 1/2 TC -1-1/2 TC-2-1/2 1/8 LSP TP-2-1/8 LSP TP-2-1/8 LSP
#8 TC-1-8 TC-2-8 9/16 TC -1-9/16 TC-2-9/16 1/4 NPT TP-2-1/4 NPT
#10 TC-l-l0 TC-2-10 5/8 TC-2-5/8 3/8 NPT TP -2-3/8 NPT
#12 TC-1 -12 TC-2-12 11/16 TC-2-11/16
1/4 TC-1 -1 /4 TC-2-1/4 3/4 TC -2-3/4
5/16 TC-1-5/16 TC -2-5/16 13{1 6 TC -2-13/16
3/8 TC-1-3/8 TC -2-3/8 7/8 TC-2-7/8
7/16 TC -1-7/16 TC -2-7/16
--------------------------------------------------------------------------------12
PHONE: 734-591-0134. FAX: 734-591-7866
FL-Tool Holders
Quick Change Tap Adapters

Axial Length Adjustment
Adapter size in table.
2a. Order by Part Number Available in

shown for Tang Drive. Tang Drive or Ball Drive

for Ball Drive.
BALL
DRIVE
I--- c
ADAPTER TAP A B D ADUST C L

SIZE SIZES DlA. DlA. DlA. LENGTH LENGTH LENGTH
TALA·l·6 0·6 .141 .110 .75

TALA·l·8 8 .168 .131 .82
TALA·l ·1 0 10 .194 .152 .82
TALA·l·12 12 .220 .1 65 .85
TALA·l ·1/4 14 & 1/4 .255 .191 .85
1 .74 1.18 .747 .394 1.28
TALA·l·5/16 5/16 .318 .238 .96
TALA·l·7/16 7/16 .323 .242 1.05
TALA·l·1/2 1/2 .367 .275 1.08
TALA·l ·3/8 3/8 .381 .286 1.02
TALA·l·9116 9/16 .429 .322 1.15
TALA·2·5/16 5/16 .318 .238' 1.03

TALA·2·7/16 7/16 .323 .242 1.12
TALA·2·1/2 1/2 .367 .275 1.15
TALA·2·3/8 3/8 .381 .286 1.09
TALA·2·9/16 9/16 .429 .322 1.22
2 1.18 1.90 1.219 .610 2.24
TALA·2·5/8 5/8 .480 .360 1.68
TALA·2·11116 11/16 .542 .406 1.74
TALA·2·3/4 3/4 .590 .442 1.81
TALA·2·13/16 13/16 .652 .489 1.81
TALA·2·7/8 7/8 .697 .523 1.87
TALA·3·5/8 5/8 .480 .360 1.56

TALA·3·11/16 11/16 .542 .460 2.10
TALA·3·3/4 3/4 .590 .442 2.16
TALA·3·13/16 13/16 .652 .489 2.17
TALA·3·7/8 7/8 .697 .523 2.23
3 1.88 2.75 1.889 .980 2.98
TALA·3·15/16 15/16 .760 .570 2.23
TALA·3·1 1 .800 .600 2.30
TALA·3·1· 1/8 11/8 .896 .672 2.36
TALA·3·1 1/4 11/4 1.021 .766 2.48
TALA·3·1 3/8 13/8 1.1 08 .831 2.55
TALA·2·1/8 SSP 1/8 SSP .3125 .234 1.02

1 .74 1.18 .747 .394 1.28
TALA·2·1/8 LSP 1/8LSP .4375 . 3~8 1.02
TALA·2·1/8 NPT 1/8 NPT .4375 .328 1.08

TALA·2·1/4 NPT 1/4 NPT .5625 .421 1.19
2 1.18 1.90 1.219 .610 2.24
TALA·2·1/2 NPT 1/2 NPT .6875 .515 1.37
TALA·2·3/8 NPT 3/8 NPT .7000 .531 1.25
TALA·3·1/4 NPT 1/4 NPT .5620 .421 1.21

TALA·3·1/2 NPT 1/2 NPT .6875 .515 1.41
TALA·3·3/8 NPT 3 3/8 NPT .7000 .531 1.88 2.75 1.889 .980 2.98 1.27
TALA·3·3/4 NPT 3/4 NPT .9063 .812 1.46
TALA·3·1 NPT 1 NPT 1.125 .843 1.58
13--------------------------------------------------------------------------------
Quick Change Tap Adapters

Axial Length Adjustment-Extended
Adapter size in table. ",", _ _ _ I_.~L~ _ _---.
2a. Order by Part Number __ -- ----=l-r t
'" /1 SHANK A B Available in
'F't---'lJ:)If--A_I.C.,--~ -=r~
shown for Tang Drive.
-----.J- t Tang Drive or Ball Drive

for Ball Drive. BALL
DRIVE
I-----C .1. ··ADJUSTMENT
ADAPTER TAP A B D ADJUST C L

SIZE SIZES DlA. DlA. DIA. LENGTH LENGTH LENGTH
TAEA·l·6 0·6 .141 .1 10 .75

TAEA·l ·8 8 .1 68 .1 31 .82
TAEA·l·l0 10 .194 .152 .82
TAEA·l· 12 12 .220 .165 .85
TAEA·l·1/4 14 & 1/4 .255 .191 .85
1 .74 1.18 .747 .394
TAEA·l·5/16 5/16 .318 .238 .96
TAEA·l·7/16 7/16 .323 .242 1.05
TAEA·l ·1 /2 1/2 .367 .275 1.08
TAEA·l ·3/8 3/8 .381 .286 1.02
TAEA·l·9/16 9/16 .429 .322 1.15
TAEA·2·5/16 5/16 .318 .238 1.03

TAEA·2·7/16 7/16 .323 .242 1.12
TAEA·2·1/2 1/2 .367 .275 1.15
TAEA·2·3/8 3/8 .381 .286 1.09
TAEA·2·9/16 9/16 .429 .322 1.22
2 1.18 1.90 1.219 .610
TAEA·2·5/8 5/8 .480 .360 1.68
TAEA·2·11/16 11/16 .542 .406 1.74
TAEA·2·3/4 3/4 .590 .442 1.81
TAEA·2·13/16 13/16 .652 .489 1.81
TAEA·2·7/8 7/8 .697 .523 1.87
TAEA·3·5/8 5/8 .480 .360 1.56

TAEA·3·1 1/16 11/16 .542 .460 2.10
TAEA·J.3/4 3/4 .590 .442 2.16
TAEA·3·13/16 13/16 .652 .489 2.17
TAEA·3·7/8 7/8 .697 .523 2.23
3 1.88 2.75 1.889 .980
TAEA·3·15/16 15/16 .760 .570 2.23
TAEA·3·1 1 .800 .600 2.30
TAEA·3·1 1/8 11/8 .896 .672 2.36
TAEA·3·1 1/4 11/4 1.021 .766 2.48
TAEA·J.l 3/8 13/8 1.108 .831 2.55
TAEA·l·1/8 SSP 1/8 SSP .3125 .234 1.02

1 .74 1.18 .747 .394 1.28
TAEA·l· 1/8 LSP 1/8 LSP .4375 .328 1.02
TAEA·2·1/8 NPT 1/8 NPT .4375 .328 1.08

TAEA·2·1/4 NPT 1/4 NPT .5625 .421 1.19
2 1.18 1.90 1.219 .6 10 2.24
TAEA·2·1/2 NPT 1/2 NPT .6875 .515 1.37
TAEA·2·3/8 NPT 3/8 NPT .7000 .531 1.25
TAEA·3·1/4 NPT 1/4 NPT .5620 .421 1.21

TAEA·3·1/2 NPT 1/2 NPT .6875 .515 1.41
TAEA·J.3/8 NPT 3 3/8 NPT .7000 .531 1.88 2.75 1.889 .980 2.98 1.27
TAEA·J.3/4 NPT 3/4 NPT .9063 .812 1.46
TAEA·3·1 NPT 1 NPT 1.125 .843 1.58
14
PHONE: 734-591-0134 • FAX: 734-591-7866
FL-Tool Holders
Quick Change Dedicated Size Radial

Floating Acme Shank Tap Holders
1. Locate desired Tap, Shank TAP DEPTH TAP
SIZE ENTERS
and Holder Series in table.
#10 1.125
#12 1.125
shown.
•
N
""""'""~
I'
KEY
"
OPTIONAL -A
COOLANT SEA~ -
----- ----------------- --- -
t \ r-
B
ACME THREAD
rn
lli - - I
L 1
T ~
:v
Radial Float
.032 Per Side
t -- ----- ----- --- - '-
0250~ E~
~I.
~ G
D .. C F-
I: E M
TAP B A
PART NUMBER C 0 E F G N M
SIZE SHANK SERIES
DSA-0-8000 1/2-16 3.000 5_562

#6 DSA-0-8001 5/8-1 6 3.000 5.562
DSA-0-8002 3/4-12 3.000 5.562
4.187 1
.141 DSA-0-8003 7/8-12 3_625 6_187
SHANK DSA-0-8004 1-12 3.625 6.187
DSA-0-8005 1 1/16-12 3_625 6_187
DSA-0-8008 1/2-16 3.000 5.562

#8 DSA-0-8009 5/8-16 3_000 5.562
DSA-0-8010 3/4-12 3_000 5.562
4.250 11/16
.168 DSA-0-8011 7/8-12 3.625 6.187
SHANK DSA-0-8012 1-12 3.625 6.187
DSA-0-8013 1 1/16-12 #0 3.625 6.187
SERIES 1.187 1.375 1.00
DSA-0-8016 1/2-16 1.500 3.000 5.562
#10 DSA-0-8017 5/8-16 3.000 5.562
DSA-0-8018 3/4-12 3.000 5.562
4.437 11/4
.195 DSA-0-8019 7/8-12 3.625 6.187
SHANK DSA-0-8020 1-12 3.625 6.187
DSA-0-8021 1 1/16-12 3.625 6.187
DSA-0-8024 1/2-16 3.000 5.562

#12 DSA-0-8025 5/8-16 3.000 5_562
DSA-0-8026 3/4-12 3_000 5.562
4.437 1 1/4
.220 DSA-0-8027 7/8-12 3.625 6.187
SHANK DSA-0-8028 1-12 3.625 6.187
DSA-0-8029 1 1/16-12 3.625 6.187
15--------------------------------------------------------------------------------

TAP DEPTH TAP
ORDERING INFORMATION SIZE ENTERS
1. Locate desired Tap, Shank y.. 1.250
5/16 1250
2. Order by Part Number 3/8 1.375
shown .
1/8 LSP 1.187
V""~""
KEY ~ I~
N
OP TIONAL -A
COOLANT SEAL\
r-
---------------- --------- - ,
t
B
ACME THREAD
~
lli--1 l- i
-.l
J:
J, j) Radial Float
.032 Per Side
! ----- -------- -------- - I-
t== .F-
0.250 ~ ~ G
D C
.1* F-
.
E M
TAP B A
PART NUMBER C D E F G N M
SIZE SHANK SERIES
DSA-D-8D32 1/2-16 3.000 5.562

1/4 DSA-0-8033 5/8-16 3.000 5_562
DSA-0-8034 3/4-12 3_DOO 5_562
4.437 1 1/4
_255 DSA-0-8035 7/8-2 3.625 6.187
SHANK DSA-0-8036 1-12 3.625 6.187
DSA-0-8037 1 1/16-12 3.625 6.187
1_00
DSA-0-8040 1/2-16 3.000 5.562
5/16 DSA-0-8041 5/8-16 3_000 5_562
DSA-0-8042 3/4-12 3.000 5.562
4.710 115/32
.318 DSA-0-8043 7/8-12 3.625 6.187
SHANK DSA-0-8044 1-12 #0 3.625 6_187
DSA-0-8045 1 1/16-12 SERIES 1.187 3.625 6.187 1.375
1.500
DSA-0-8048 1/2-16 3.000 5.562
3/8 DSA-0-8049 5/8-16 3.000 5.562
DSA-0-8050 3/4-12 3.000 5.562
4_750 19/16
.381 DSA-0-8051 7/8-12 3.625 6_187
SHANK DSA-0-8052 1-12 3.625 6.187
DSA-0-8053 1 1/16-12 3.625 6.187 1.125
1/8 LSP DSA-0-8500 1/2-16 3_000 5.562

DSA-0-8501 5/8-16 3_000 5_562
4.125 15/16
.437 DSA-0-8502 3/4-12 3.000 5.562
SHANK DSA-0-8503 7/8-12 3.625 6_187
-----------------------------------------------------------------------------16
PHONE: 734-591-0134 • FAX: 734-591-7866
FL-Tool Holders

iAP DEPTH TAP
SIZE ENTERS
ORDERING INFORMATION y.. 1.250
1. Locate desired Tap, Shank
5/16 1.250
3/8 1.375
2. Order by Part Number 7/16 1.375
shown. ~ 1.375
N ...
w""'cc,~
I'
KE Y
OPTIONAL - A
COOLAN T SE AL\ ~ ~ ~
-- -------- --------------- -
~
r-
t I T l" Radial Float
B
ACME THREAD U1L-J - L -L ..1/ .032 Per Side
! ------- - ---- ~ - - -- -- -- -
'--
0.250 ~
.E .\. - G
I: D
E
C 'F -
TAP B A
PART NUMBER C 0 E F G N M
SIZE SHANK SERIES
DSA·l ·8134 3/4·12 3.000 5.562

1/4
DSA·l ·8135 7/8·12 3.625 6.187
DSA·l ·8136 1·12 3.625 6.187 4.437 11/4
.255
DSA·l ·8137 1 1/16·12 3.625 6.187
SHANK
DSA·l ·8138 1 3/8·12 4.625 7.187
1.00
DSA·l·8142 3/4·12 3.000 5.562
5/16
DSA·l ·8143 7/8·12 3.625 6.187
DSA·l ·8144 1·12 3.625 6.187 4.710 1 15/32
.318
DSA·l ·8145 1 1/16·12 3.625 6.187
SHANK
DSA·l ·8146 13/8·12 4.625 7.187
DSA·l ·8150 3/4·12 3.000 5.562

3/8 #1
DSA·l ·8151 7/8·12 3.625 6.187
DSA·l ·8152 1·12 SERIES 1.187 3.625 6.187 1.375 4.750 19/16
.381 1.812
DSA·l ·8153 1 1/16·12 3.625 6.187
SHANK
DSA·l·8154 13/8·12 4.625 7.187
DSA·l·8157 3/4·12 3.000 5.562

7/16
DSA·l ·8158 7/8·12 3.625 6.187
DSA·l·8159 1·12 3.625 6.187 1.1 25 4.968 125/32
.323
DSA·l·8160 1 1/16·12 3.625 6.187
SHANK ,
DSA·l·8161 13/8·12 4.625 7.187
DSA·l·8164 3/4·12 3.000 5.562
1/2
DSA·l ·8165 7/8· 12 3.625 6.187
DSA·l·8166 1·12 3.625 6.187 5.187 2
.367
DSA·l ·8167 1 1/16·12 3.625 6.187
SHANK
DSA·l ·8168 13/8·12 4.625 7.187
17 -----------------------------------------------------------------------------

TAP DEPTH TAP
ORDERING INFORMATION SIZE ENTERS
1. Locate desired Tap, Shank 9/16 1.500

and Holder Series in table. 1.187
1/8 LSP
"'i
" DODR FF ~
2. Order by Part N umber 'KEY N
sh own.
OPT IDNAL IL\
COOLANT SEAL I' r- A
r-
Radial Float
------------------------- -
t \ .0 32 Per Side
B
ACME THREAD
rn
lli - f-
L
r T 1"1
~ Y
t ----- ------- -------- -
~
0250 ~
.E .1. - G
I: D
E
C F -
TAP B A
SIZE SHANK SERIES
DSA·l·8172 3/4·12 3.000 5.562

9/16
DSA·l·8173 7/8·12 3.625 6.187
DSA·l·8174 1·12 3.625 6.187 1.125 5.281 23/32
.429
DSA·l·8175 11/16·12 3.625 6.187
SHANK #1
DSA·l ·8176 1 3/8·12 4.625 7.187
SERIES 1.187 1.375
DSA·l ·8510 3/4·12 1.812 3.000 5.562
1/8lSP
DSA·l ·8511 7/8·12 3.625 6.187
DSA·l·8512 1·12 3.625 6.187 1.250 4.125 15/16
.437
DSA·l·8513 1 1/16·12 3.625 6.187
SHANK
DSA·l·8514 13/8·12 4.625 7.187
I FEATURES AND BENEFITS I

• ALLOWS FOR 1 /32 RADIAL FLOAT
• ADJUSTABLE FOR VERTICAL OR
HORIZONTAL MACHINING
• DURABLE THREE PIECE DESIGN
• ARMORCLAD®SURFACE COATING FOR
CORROSION RESISTANCE
• AUTOMATICALLY COMPENSATES
OPERATING PROCEDURE
FOR MISALIGNMENT
• POSITIVE DRIVE (2) Pull the operating
sleeve down.
o Push Tap into the

Holder.
CD Release the
Operating Sleeve
18
PHONE: 734-591-0134 • FAX: 734-591 -7866
FL-Tool Holders

Floating Acme Shank Tap Holders TAP DEPTH TAP
SIZE ENTERS
ORDERING INFORMATION 7/16 1.375
1. Locate desired Tap, Shank 1.375
and Holder Series in table. 9/16 1.500

1/8 PLG 1.187
11, PLG 1.312
VO""'~c~
I~
N
shown. KE Y
OPTIONAL
COOLANT SEAL\ ~
-A
-.. ~
·1
Radial Float
------ ------------------- -
t m\ r T "'1"-
032 Per Side
B
ACME THREAD W---1 - -
l 1- .v
i --- ---- ------ -------- - l-
D
0.250 ~
.E c l F-
- G
I: E M
TAP B A
SIZE SHANK SERIES
7/16 DSA·2·8259 1·12 3.625 6.593

.323 DSA·2·8260 11/16·12 3.625 6.593 5.125 1 25/32
SHANK DSA·2·8261 13/8·12 4.625 7.593
1/2 DSA·2·8266 1·12 3.625 6.593

.367 DSA·2·8267 11/16·12 3.625 6.593 1.125 5.343 2
SHANK DSA·2·8268 13/8·12 4.625 7.593
9/1 6 DSA·2·8274 1·12 3.625 6.593

.429 DSA·2·8275 11/16·12 3.625 6.593 5.437 23/32
SHANK DSA·2·8276 13/8·12 4.625 7.593
5/8 DSA·2·8278 1·12 3.625 6.593

.480 DSA·2·8279 11/16·12 3.625 6.593 5.656 25/16
SHANK DSA·2·8280 1 3/8·12 4.625 7.593
1.250
3/4 DSA·2·8282 1·12 #2 3,625 6.593
.590 DSA·2·8283 1 1/16·12 SERIES 1.468 3.625 6.593 1.500 5.843 21/2
SHANK DSA·2·8284 13/8·12 2.187 4.625 7.593
7/8 DSA·2·8286 1·12 3.625 6.593

.697 DSA·2·8287 1 1/16·12 3.625 6.593 1.500 6.281 215/16
SHANK DSA·2·8288 1 3/8·12 4.625 7.593
1/8lSP DSA·2·8520 1·12 , 3.625 6.593

.437 DSA·2·8521 11/16·12 3.625 6.593 1.125 4.28 15/16
SHANK DSA·2·8522 13/8·12 4.625 7.593
1/4 NPT DSA·2·8528 1·12 3.625 6.593

.562 DSA·2·8529 1 1/16·12 3.625 6.593 1.250 4.468 1 1/8
SHANK DSA·2·8530 13/8·12 4.625 7.593
3/8 NPT DSA·2·8536 1·12 3.625 6.593

.700 DSA·2·8537 11/16·12 3.625 6.593 1.375 4.53 13/16
SHANK DSA·2·8538 13/8·1 2 4.625 7.593
19 -----------------------------------------------------------------------------

Floating Acme Shank Tap Holders TAP OEPTH TAP
SIZE ENTERS
ORDERING INFORMATION SIB 1.500

1. Locate desired Tap Shank 0/. 1.750
7/B 1.750
3/B PT 1.375
2. Order by Part Number N
1
WOODRUFF
'~
KEY
shown .
OPT IONAL 'L\
COOLANT SEAL 1 ~
r-A
h ~
Radial Float
------- -------- -- ---- - -
t m\ .0 32 Per Side
B I I l'
ACME THREAD lli - f-
L 1 1/
i - - - - --- - -
'--
-
D
0.250 ~
.E C .1. F-
'- G
I: E M
TAP B A
SIZE SHANK SERIES
5/8 OSA·3·8379 1 1/16·12 3.625 6.687

.480 OSA·3·8380 1 3/8·12 4.625 7.687 1.250 6.06 25/16
SHANK OSA·3·8381 1 7/8·12 5.625 8.687
3/4 OSA·3·8383 11/16·12 3.625 6.687

.590 OSA·3·8384 1 3/8·12 4.625 7.687 1.375 6.25 21/2
SHANK OSA·3·8385 1 7/8·12 5.625 8.687
7/8 OSA·3·8386 1 1/16·12 #3 3.625 6.687

.697 OSA·3·8387 1 3/8·12 SERIES 1.562 4.625 7.687 1.500 1.500 6.68 215/16
SHANK OSA·3·8388 1 7/8·12 2.750 5.625 8.687
1" OSA,3·8389 1 1/16·12 3.625 6.687
.800 OSA·3·8390 1 3/8·12 4.625 7.687 1.625 7.06 35/16
SHANK OSA·3·8391 1 7/8·12 5.625 8.687
1 1/8 OSA·3·8392 11/16·12 3.625 6.687
.896 OSA·3·8393 1 3/8·12 4.625 7.687 1.750 7.31 39/16
SHANK OSA·3 ·8394 1 7/8·12 5.625 8.687
TAP B A
SIZE SHANK SERIES
3/8 NPT OSA·3·8545 1 1/16·12 3.625 6.687

.700 OSA·3·8546 1 3/8·12 4.625 7.687 4.93 1 3/16
SHANK OSA·3·8547 1 7/8·12 5.625 8.687
1.375
1/2 NPT OSA·3·8553 11/16·12 #3 3.625 6.687
.687 OSA·3·8554 1 3/8·12 SERIES 1.562 4.625 7.687 1.500 5.25 11/2
SHANK OSA·3·8555 1 7/8·12 2.750 5.625 8.687
3/4 NPT OSA·3·8560 1 1/16·12 3.625 6.687

.906 OSA·3·8561 1 3/8·12 4.625 7.687 1.625 5.50 13/4
SHANK OSA·3·8562 1 7/8·12 5.625 8.687
---------------------------------------------------------------------------20
PHONE: 734-591-0134 • FAX: 734-591-7866
FL-Tool Holders
CO'l let Type Radial Floating Acme

Shank Reamer Holders
1. Locate desired Collet, Shank .42
OPTIONAL
and Holder Series in table. POSITIVE DRIVE
1-+_ __ _ REF. ---f--~
N
shown. H ------~+-------~
A
-L--- t:t:.=----=------=----c-===--
:.=:- -----~-
HlEI[It-!
~
Radial Float
.032 Per Side
I. O. 2 50~ E - I ~I F
D • c -t--- REF---l
COLLET B A REF REF

PART NUMBER C D G H
SERIES SHANK SERIES F N
SAA·O·9100 1/2·1 2 3.00
SAA·O·9l0l 5/8·12 3.00
#0
SAA·0·9102 3/4·12 3.00
16 SERIES 1.670 1.10 3.50 1.800
SAA·Q·9104 1"·12 3.625
1.5
SAA·O·9105 1·1/16· 12 3.625
SAA·0·9106 1·3/8 ·12 1.187 4.625
SAA·1·91 07 5/8·12 3.00
SAA·1·91 08 3/4·12 #1 3.00
20 SAA·l ·9ll0 1"·12 SERIES 3.625 1.430 1.34 3.29 1.450
SAA· 1·91" 1·1/16· 12 1.812 3.625
SAA·1·91 12 1·3/8·12 4.625
SAA·2·9115 3/4·1 2 3.00

#2
SAA·2·9117 1"·12 3.625
25 SERIES 1.468 2.060 1.65 4.20 1.812
SAA·2·9118 1·1/16· 12 3.625
2.187
SAA·2·9119 1·3/8·12 4.625
SAA·3·9125 1·1/16 #3 3.625

32 SAA·3·91 26 1·3/8 SERIES 1.562 4.625 2.30 2.00 4.53 2.125
SAA·3·9127 1·7/8 2.750 5.625
* See page 32 for Positive drive Information

* See pages 23-26 for Collet Information
All SA Collet Holders are

Available with Positive drive
Call for Detail Information
/.1--------------------------------------------------------------------------------
Collet Type Radial Floating Straight

Shank Reamer Holders OP TI ONAL
COOLANT SEAL
ORDE~NGINFORMAnON
1. Locate desired Collet, Shank
B Radial Float
shown .
i .032 Per Side
L-n .1.
COllET B A REF REF
PART NUMBER C 0 G
SERIES SHAN.K SERIES F N
SAA·0·9201 3/4·12 #0
16 SAA·0·9202 1·12 SERIES 1.100 2.812
SAA·0·9203 11 /2·1 2 1.5
1.187 4.00 1.600
SAA·0·9206 3/4·12 #1
20 SAA·1·9207 1·12 SERIES 1.340 2.562
SAA·1·9208 1 1/2·12 1.812
#2
SAA·2·9211 1·12
25
SAA·2·9212 1 1/2·12
SERIES 1.468 1.375 1.650 2.844
2. 187
5.00
#3
SAA·3·9216 1 1/2·12
32 SERIES 1.562 1.660 2.000 3.219
SAA·3·9217 13/4·12
2.750
Collet Type Radial Floating Cat V

Flange Reamer Holders 'B'-V
CAT FLANGE
A
1. Locate desired V-Flange,
collet series and Holder size
in table. GAGE LINE Radial Float
,032 Per Side
RUENTION KNOBS AVAILA BLE
UPON REQUEST
COLLET B A
PART NUMBER C F G
SERIES SHANK , SERIES
SAC·0·40·16 40
16 1.500 1.093 1.375 1.100
SAC·0·50·16 50
SAC·1·40·20 40
20 1.812 1.125 1.625 1.340
SAC·1·50·20 50
SAC·2·40·25 40
25 2.187 1.625 1.625 1.650
SAC·2·50·25 50
SAC·3·40·32 40
32 2.750 1.937 1.937 2.000
SAC·3·50·32 50
22
PHONE: 734-591-0134 • FAX: 734-591-7866
FL-Tool Holders
Single Angle Collets (Series 16)

INCH METRIC
1. Locate desired Shank Size
in table. PART PART CLAMPING RANGE
CLAMPING RANGE
NUMBER NUMBER MM INCH.
2. Order by Part Number SA-16-1/16 .062-_047 SA-16-Ml 1-.05 .039·.019
shown .
SA-16-3/32 .093-078 SA-16-M2 2·1 .079·.039
SA·16·1/8 .125·. 110 SA-16-M3 3·2 .118-.079
SA-16-5/32 .156·.141 SA·16·M4 4-3 .157·. 118

SA-16-M5 5·4 .197·.157
SA-16·3/16 187'. 172
SA·16·M6 6-5 .236-. 197
SA·16·7/32 .218-.203
SA-16-M7 7-6 .276-.236
SA- 16-1/4 250'.235
SA·16·M8 8-7 .315-.276
SA·16-9/32 .280-.266
SA-16-M9 9·8 .354·.315
SA·16-5/16 .312-.297
SA-16-Ml0 10·9 .394-.354
SA-16-11 /32 .344-.328
SA·16·3/8 .375·.360
SA- 16·13/32 .406-.391

in table. INCH METRIC
PART CLAMPING PART CLAMPING RANGE
NUMBER RANGE NUMBER MM INCH
shown .
SA-20·1 /16 .062·.047 SA·20-M2 2-1 .079·.039
SA-20-3/32 .093·.078 SA·20·M3 3·2 .118-.079
SA-20-1/8 .125·.110 SA-20·M4 4·3 .157·. 118

SA-20-5/32 .1 56·. 141 SA·20·M5 5-4 .197-.157
SA.·20·3/16 .187·.172 SA-20-M6 6·5 .236-.197
SA-20-7I32 .218·.203 SA-20-M7 7·6 .276·.236
SA·20·1/4 .250·.235 SA·20-M8 8·7 .315·.276
SA-20-9/32 .281 ·.203 SA-20·M9 9-8 .354-.315
SA·20-5/16 .312-.297 SA·20·Ml0 10·9 .394·.354
SA-20-11/32 .343·.328 SA-20·Mll 11 -10 .433,.394
SA-20-3/8 .375·.360 SA-20-M12 12-11 .472-.433
SA-20·13/32 .406-.391 SA·20·M13 13·12 .512·472
SA-20·7/16 .437'.422
SA-20-15/32 .468·.453
SA-20-1/2 500-.485
23 -----------------------------------------------------------------------------
ORDERING INFORMATION INCH METRIC
1. Locate desired Shan k Size
PART CLAMPING PART CLAMPING
in table. NUMBER NUMBER
RANGE MM INCH
SA·251/16 .062·.047 SA·25 M2 2·1 .079·.039
SA·253/32 :093·.078
shown . SA·25 M3 3·2 .118·.079
SA·25 1/8 .125·.110
SA·25 M4 4·3 .157·. 118
SA·255/32 .156·.141
SA·253/16 .187·.172 SA·25 M5 5-4 .197·. 157
SA·257/32 .218·.203 SA·25 M6 6·5 .236·.197
SA·251 /4 .250·.235
SA·25 M7 7·6 .276·.236
SA·259/32 .281·.266
SA·25 M8 8·7 .315·.276
SA·255/16 .31 2·.297
SA·2511/32 .343·.328 SA·25 M9 9·8 .354·. 315
SA·253/8 .375·.360 SA·25 Ml0 10·9 .394·.354
SA·2513/32 .406,.39 1
SA·25 Mll 11 ·10 .433·.394
SA·257/16 .437·.422
SA·25 M12 12·11 .472-.433
SA·2515/32 .468·.453
SA·251/2 .500·.485 SA·25 M13 13·12 .512·.472
SA·25 17/32 .531 ·.516 SA·25 M14 14·13 .551'.5 12
SA·259/16 .562·.547
SA·25M15 15·14 .591 ·.551
SA·2519/32 .593·. 578
SA·25 M16 16·15 .630·.591
SA·255/8 .625·.610

INCH METRIC
in table. PART CLAMPING PART CLAMPING RANGE
NUMBER RANGE NUMBER MM INCH
2. Order by Part Number SA·32·3132 .093·.078 SA·32·M3 3·2 .1 18·.079
shown. SA·32·1/8 .125·. 110 SA·32·M4 4·3 .157·. 118
SA·32·5132 .156·.141 SA·32·M5 5-4 .197'. 157
SA·32·3/16 .187·.172 SA·32·M6 6·5 .236·. 197
SA·32·7132 .2 18·.203 .276·.236
SA·32·M7 7·6
SA·32·1/4 .250·.235
SA·32·M8 8·7 .315·.276
SA·32·9132 .281 ·.266
SA·32·M9 9·8 .354·.315
SA·32·5/16 .312·.297
SA·32·M l 0 10·9 .394·.354
SA·32·11/32 .343·.328
SA·32·3/8 .375·.360 SA·32·Mll 11·10 .433· .394
SA·32·13/32 .406,.391 SA·32·M12 12·11 .472-.433
SA·32·7I16 .437·.422 SA·32·M13 13 - 12 .512·.472
SA·32·15/32 .468·.453 SA·32·M14 14·13 .551 ·.512
SA·32·1/2 .500·.485 SA·32·M15 15· 14 .591 ·.551
SA·32·1 7/32 .531 ·.516 SA·32·M16 16·15 .630·. 591
SA·32·9/16 .562·.547 SA·32·M17 17·16 .669·.630
SA·32·19/32 .593·.578 SA·32·M18 18·17 .709·.669
SA·32·5/8 .625·.610
SA·32·M19 19·18 .748·.709
SA·32·21/32 .656·.641
SA·32·M20 20·19 .787·.748
SA·32·11/16 .687·.672
SA·32·23/32 .718·.703
SA·32·3/4 .750·.735
-------------------=================~~----------------------24
PHONE: 734·591·0134. FAX: 734·591·7866
FL-Tool Holders
SAX Tap Collets With Internal

Square Drive
1. Locate desired Tap Size and
Collet Series in table.

shown.
TAP SAX 16 SAX 20 SAX 25 SAX 32

SIZE PART # PART# PART # PART #
#8 SAX ·16·168 SAX· 20-168 SAX· 25·168 SAX· 32·168
#10 SAX ·16·194 SAX ·20·194 SAX ·25·194 SAX ·32·194
#12 SAX ·16·220 SAX ·20·220 SAX ·25·220 SAX ·32·220
1/4 SAX ·16·255 SAX ·20·255 SAX ·25·255 SAX ·32·255
5/16 SAX ·20·318 SAX ·25·318 SAX ·32·318
3/8 SAX ·20·381 SAX ·25·381 SAX ·32·381
7/16 SAX ·20·323 SAX ·25·323 SAX ·32·323
1/2 SAX ·20·367 SAX ·25·367 SAX ·32·367
9/16 SAX ·25-429 SAX ·32-429
5/8 SAX ·25·480 SAX ·32-480
11/16 SAX ·32·542
3/4 SAX ·32·590
13/16 SAX ·32·652
ALSO AVAILABLE IN METRIC SIZE TAP SHANKS UPON REQUEST
DIMENSIONAL INFORMATION
TAP SIZE B
A
RANGE SA 16 SA 20 SA 25 SA 32
#8 -1/4 0.709 0.374 0.531 0.630 0.866
5/16 - 1/2 0.866 0.374 0.472 0.709
9/16 - 7/8 0.984 0.374 0.591
* THE TAP LOCATES OFF THE ID OF THE COLLET AND DRIVES OFF THE SQUARE OF THE COLLET
* POSITIVE DRIVE GIVES ACCURACY AND RIGIDABILITY
25-----------------------------------------------------------------------------
Single Angle Collet Accuracy
INCH METRIC
CLAMPING RANGE CLAMPING RANGE
MAXIMUM HR. MAXIMUM HR.
D D
L L
PRECISION HIGH PRECISION PRECISION HIGH PRECISION
MIN. MAX. MIN. MAX.
DIN 6499 · DIN 6499 DIN 6499 DIN 6499
0.039 0.063 0.236 1.0 1.6 6
0.063 0.118 0.394 1.6 3.0 10
0.0006 0.0003 0.015 0.008
0.118 0.236 0.630 3.0 6.0 16
0.236 0.394 0.984 6.0 10.0 25
0.394 0.709 1.575 10.0 18.0 40
0.0008 0.0004 0.020 0.010
0.709 1.024 1.969 18.0 26.0 50
1.024 1.339 2.362 0.0010 26.0 34.0 60 0.025
INSERTING AND REMOVING SA COLLETS
INSERTING REMOVING
INSERT COLLET INTO NUT AT AN ANGLE TO 1 LOOSEN THE COLLET NUT ASS 'Y WITH WRENCH
ENGAGE CLIP IN NUT TO SEAT INTO THE 2 REMOVE THE TOOL AND UNSCREW THE NUT
GROOVE OF THE COLLET FROM HOLDER
2 SCREW NUT ONTO THE COLLET HOLDER 3 HOLDING ONTO THE NUT BY PUSH SIDEWARD ON
PARTWAY DOWN THE END OF THE COLLET, THUS UNSNAPPING IT
3 INSERT THE TOOL AND TIGHTEN DOWN WITH OUT OF THE ECCENTRIC RING LOCATED IN THE
WRENCH COLLET NUT
GROOVE IN COLLET
INSTALLATION ANGLE SHOWN

ECCENTRIC RING OF NUT
IMPORTANT NOTE:
NEVER SCREW THE NUT DOWN WITH OUT FIRST CHECKING THAT THE COLLET IS PROPERLY INSTALLED.
-----------------------------------------------------------------------------26
PHONE: 734-591-0134. FAX: 734-591-7866
FL-Tool Holders
Collet Type Radial Floating

Acme Shank Tap and Reamer Holders
1. Locate desired Collet, Shank
I.tOODRUFF
'~
and Holder series size in table . KEY N

I- ~A
r-
shown . ---------- ---- ----------- - ~
3. See Page 29 for Collet B - -I-

~
, I H1 t
G Radial Float
~
Information . ACME THREAD .032 Per Side
~
~
L - ------------ --- -- -- -
L..-
l-
.25
~.E lr--
I: D
E
C
COLLET B A
PART NUMBER C 0 F G N
SERIES SHANK SERIES
TCA·0·9501 1/2·16 3.000

TCA·0·9502 5/8·16 3.000
l ·TCA
TCA·0·9503 3/4·12 #0 3.000
RANGE 1.125 1.125 213/16
TCA·0·9504 1·12 1.5 3.625
0·1/2
TCA·0·9505 1 1/16·12 3.625
TCA·0·9506 13/8·12 1.187 3.625
TCA·l ·9509 3/4·12 3.000

l·TCA
TCA·l ·9510 112 #1 3.625
RANGE 1.125 1.125 213/16
TCA·l ·9511 11/16·12 1.812 3.625
0·1/2
TCA·l ·9512 13/8·12 4.625
2·TCA TCA·2·9516 112 3.625

#2
RANGE TCA·2·9517 1 1/16·12 1.468 3.625 1.156 1.343 3.125
2.187
9/16·3/4 TCA·2·9518 13/8·12 4.625
3·TCA TCA·3·9524 1 1/16·12 3.625 3.750

#3
RANGE TCA·3·9525 13/8·12 1.562 4.625 1.687 2.125 3.750
2.750
7{8·11/4 TCA·3·9526 1 7{8·12 5.625 4.000
TCA·49528 1 1/16·12 3.625 4.750

4·TCA
TCA·49529 13/8·12 #4 1.750 4.625 2.343 2.750 4.750
RANGE
TCA·49530 17/812 5.625 4.970
5·TCA TCA·5·9531 13/8·12 4.625 5.970

#5 2.125 3.187 3.750
RANGE TCA·5·9532 1 7/8·12 5.625 6.187
* HOLDERS SERIES #4TCA AND #5TCA

ARE NON STOCKED ITEMS
27-----------------------------------------------------------------------------
Collet Type Radial Floating Straight

Shank Tap and Reamer Holders
1. Locate desired Collet, Shan k
~N
and Holder series in table.
2. Order by Part Number r-

shown.
I
-
B - -I-
-
Hi t G
Radial Float
~ ~
.032 Per Side
L '---'-----.
-
-
I: D .1.
E
elF-
COLLET PART B A
C D F G N
SERIES NUMBER SHANK SERIES
l ·TC TCA·O·9552 3/4

#0
RANGE TCA·0·9553 7/8 3.00
1.5
0·1/2 TCA·0·9554 1
TCA·l ·9559 3/4 1.187 1.125 1.125 2.312

l·TC TCA·l ·9560 7/8
#1
RANGE TCA·l ·9561 1 3.50
1.812
0·1/2 TCA·l ·9562 1 1/4
TCA·l ·9563 11/2
TCA·l ·9566 1
2TC
TCA·l·9567 11/4 #2
RANGE 1.468 4.00 1.156 1.687 2.625
TCA·2·9568 1 1/2 2.187
9/16·3/4
TCA·2·9569 13/4
TCA·3·9571 11/4
3·TC
TCA·3·9572 11/2 #3
RANGE 1.562 5.00 1.687 2.125 3.25
TCA·3·9573 13/4 2.75
7/8·1 1/4
TCA·3·9574 2
* See page 29 for Collet Information
---------------------------------------------------------------------------- 28
PHONE: 734-591-0134 • FAX: 734-591-7866
FL-Tool Holders
Tap Collets r-
ITr,;;~-+f--- E-
c::-.....
E
=-1
ORO ERING INFORMATION
Holder series size in table .
Shown .
@ U - __
D A I--
~ 'c
I
f-
~H-
FL·TOOL D DEPTH
TAP SHANK FORD
PART A B C HOLDER E F TAP ENTERS
SIZE DIA REF#
NUMBER SERIES (HI
0·6 .141 1·TC·141 TA3·141C .1415 .115 .19 .63
8 .168 1·TC·168 TA3·168C .1685 .136 .25 .69
10 .194 1·TC·194 TA3·194C .1945 .157 .25 .69
12 .220 1·TC·220 TA3·220C .2205 .170 .28 .72
1/4 .255 1·TC·255 TA3·255C .2555 .197 .28 #1 .72
1.00 .44
5/16 .318 1·TC·318 TA3·318C .3185 .244 .31 .625 .75
3/8 .381 1·TC·381 TA3·381C .3815 .292 .56 .81
7/16 .323 1·TC·323 TA3·323C .3235 .249 .38 .85
1/2 .367 1·TC·367 TA3·367C .3675 .282 .56 .87
9/16 .429 2·TC·429 TA3·429C .4295 .330 .44 1.00
#2
5/8 .480 2·TC·480 TAJ.480C .4805 .369 .44 1.19 .50 1.06
1.000
3/4 .590 2·TC·590 TA3·590C .5905 .452 .69 1.18
7/8 .697 3·TC·697 TA3·697C .6975 .533 .50 1.38
1 .800 3·TC·800 TA3·800C .8005 .611 .50 #3 1.43
1.44 .62
1·1/8 .896 3·TC·896 TA3·896C .8965 .684 .81 1.375 1.50
1.1/4 1.021 3·TC·l021 TA3·1021C 1.0215 .781 .81 1.62
#1 .81
1/8 SSP .312 1·TC·312 TA3·312C .3125 .240 .38 1.00 .44
.625 .81
1/8 LSP .437 2·TC·437 TA3·437C .4375 .335 .38 #2 .88

1.19 .50
1/4P .562 2·TC·562 TA3·562C .5625 .430 .69 1.000 .94
3/8P .700 3·TC·700 TA3·700C .7005 .541 .38 1.12
#3
1/2P .687 3·TC·687 TA3·687C .6875 .525 .50 1.44 .62 1.25
1.375
3/4P .906 3·TC·906 TA3·906C .9065 .691 .81 1.31
Reamer Collets
1. Locate desired Reamer and 2. Order by Part Number
Holder series size in table. Shown .
- L-
FL·TOOL A B C F H L M
REAM SHANK HOLDER +.000 +.000
PART # ± ±.002 ± ±
SIZE DIA .010
NUMBER .0005 ·.001 .010 SERIES ·.001 ·.002
1/8 .1190 1·TC·119R .1 195 -
5/32 .1510 1·TC·151R .1515 .098
3/16 .1805 1·TC·181R .1810 .098
7/32 .2075 1·TC·208R .2080 .126
#1
1/4 .2405 1·TC·241 R .2410 .126 .69 .499 .396 1.00
.625
9/32 .2485 1·TC·249R .2490 .126
5/16 - 11/32 .2807 1·TC·281R .2812 .166
3/8 -13/32 .3120 1·TC·312R .3125 .166
7/16-15/32 .3745 HC·375R .3750 .207 #2

.81 .874 .626 1.19
1.000
1/2 - 19/32 .4370 2·TC·437R .4375 .247
5/8 - 23/32 .5620 3·TC·562R .5625 .307
#3
3/4 - 27/32 .6245 3·TC·625R .6250 .377 .94 1.249 .935 1.44
1.375
7/8 - 31/32 .7495 J.TC·750R .7500 .477
29 -----------------------------------------------------------------------------
Morse Taper Radial Floating Acme

Shank Tap and Reamer Holders A, B,
1. Locate desired Morse Taper
IJDDDR UFF
KE Y r:~
N A-t---r
shown . B Radial Float
ACME THREAD
.032 Per Side
Type A
PART A B F
C D K N
NUMBER SIZE SHANK MT
MTA-1-9830 7/8-12
MTA-1-9831 1.812 1-12 1.187 3_625 lMT .968 3.968
MTA-1-9832 11/16-12
MTA-2-9833 11/16-12 3.625

2.187 1.468 2MT .156 4.281
MTA-2-9834 1 3/8-12 4.625
MTA-3-9838
13/8-12
MTA-3-9839 2.750 1.562 4.625 3MT .187 5.281
1 7/8-12
MTA·3-9840
shown.
., - - - - ~=r------jr=IN~

B
ACME THREAD t-+--ttt--
---- f
- G
Radial Float
_ ___ ~ .032 Per Side
Type B -: 5j .E cl,J
PART A B F
C D J K N
MTA·1 -9810 7/8-12

MTA-1-9811 1.81 2 1-12 1.187 3.625 lMT .812 .968 2.625
MTA·l ·9812 11/16-12
MTA-1-9813 1 1/16-12 3.625

2.1 87 1.468 2MT 1.125 1_031 3.00
MTA-2-98 14 13/8-1 2 4.625
MTA-3-9815 2.750 13/8· 12 4.625 3MT 3.625

1.562 1.437 1.562
MTA-3-9816 2.750 1 7/8-12 5.625 3MT 3.875
30
PHONE: 734-591-0134 • FAX: 734-591-7866
FI-Tool Holders
Morse Taper Radial Floating Acme

Shank Tap and Reamer Holders C
'~
1. Locate desired Morse Taper I.'OO DR A
and Holder size in table. KEY UF F \ I
r-
-
-
shown .
AC ME
!
~HREAD
T - -
,...
..,.,
---<-:
.......
-I- 1-1-- - -- t
G
Radial Float
.032 Per Side
L -
-I- 1- 1- - --- - ~
J
~
-
Type C 1---1
. - D - ----.--+--1. --l-, c
PART A B F
C 0 J K N
MTA·'·9819 7{8·12
MTA·'·9820 1.812 1·12 1.187 3.625 lMT .812 .968 2.625
MTA·l ·9821 11{16·12
MTA·'·9823 1 1/16·12 3.625

2.187 1.468 2MT 1.125 1.031 3.00
MTA·2·9824 13{8·12 4.625
MTA·3·9826 2.750 13{8·12 4.625 3MT 3.625

1.562 1.437 1.562
MTA·3·9828 2.750 1 7{8·12 5.625 3MT 3.875
C-NAT'L ACME THREAD

D- SET SCRE'w' SIZE
Adjustable Acme Nuts

shown .
f--- A -~-l
PART ACME A B 0
NUMBER HREAO 00 SIZE WIDTH SET SCREW
Fl·622 1{2·16 .875 .406 1{4·28

Fl·623 5{8·16 1.00 .406 1{4·28
Fl·624 3{4·12 1.250 .406 1{4·28
Fl·625 7{8·12 1.250 .406 1{4·28
Fl·626 1"·12 1.500 .406 1{4·28
Fl·627 1 1{16·12 1.562 .406 1{4·28
Fl·628 13{8·12 1.875 .406 1{4·28
Fl·629 1 7{8·12 2.625 .625 5/16·24
31----------------------------------------------------------------------------
FL-Tool Holders
Tap Shank Information for U.S.

Standard Taps
sauAR~I1~---r=-=-:::~:
::::::::==-::-,..:
::::::
SQUARE A/ F SHANK DIAM .
MACHINE SCREW NOM. METRIC DIAM. SHANK SQUARE SQUARE

NOM. FRACT. DIAM. INCHES
SIZE NO. MILLIMETERS DIAMETER A/F LENGTH
0 1/16 M1.6 .141 .110 .187
1 Ml .8 .141 .110 .187
2 M2. M2.2 .141 .110 .1 87
3 3/32 M2.5 .141 .110 .187
4 .141 .110 .187
5 1/8 M3. M3.15 .141 .110 .187
6 M3.5 .141 .110 .187
8 5/32 M4 .168 .131 .250
10 3/16 M4.5. M5 .194 .152 .250
12 7/32 .220 .165 .281
14 1/4 M6. M6.3 .255 .191 .312
5/16 M7. M8 .318 .238 .375
3/8 Ml0 .381 .286 .437
7/16 .323 .242 .406
1/2 M12. M12.5 .367 .275 .437
9/16 M14 .429 .322 .500
5/8 M16 .480 .360 .562
11/16 M18 .542 .406 .625
3/4 .590 .442 .687
13/16 M20 .652 .489 .687
7/8 M22 .697 .523 .750
15/16 M24 .760 .570 .750
1 M25 .800 .600 .81 2
1·1/16 M27 .896 .672 .875
1·1/8 .896 .672 .875
1·3/16 M30 1.021 .766 1.000
1·1/4 1.021 .766 1.000
1·5/16 M33 1.108 .831 1.062
1·3/8 1.108 .831 1.062
1·7/16 M36 1.233 .925 1.125
1·1/2 1.233 .925 1.125
1·5/8 M39 1.305 .979 1.1 25
1·3/4 M42 1.430 1.072 1.250
1·7/8 1.519 1.139 1.250
2 M48 1.644 1.233 1.375
2·1/8 1.769 1.327 1.375
2·1/4 M56 1.894 1.420 1.437
2·3/8 2.019 1.514 1.437
2·1/2 2.100 1.575 1.500
2·5/8 M64 2.225 1.669 1.500
2·3/4 2.350 1.762 1.562
2·7/8 M72 2.475 1.856 1.562
3 2.543 1.907 1.625
3-1 /8 2.668 2.001 1.625
3·1/4 M80 2.793 2.095 1.750
3·3/8 2.883 2.162 1.750
3·1/2 3.008 2.256 2.000
3-5/8 M90 3.133 2.350 2.000
3·3/4 3.217 2.413 2.125
3·7/8 3.342 2.506 2.125
4 Ml00 3.467 2.600 2.250
PHONE: 734·591·0134 • FAX.: 734·591·7866

FL-TOOL HOLDERS
Phone: 734-591-0134 · Fax: 734-591-7866
VVVI/W, fltoolholders, com
PRECISION TOOLHOLDERS FOR

GUN DRILLS AND REAMERS
• Guaranteed Accuracy
• Easy Operation
• Compact Size
• Pilot Type Flange Mounted
• Patented
FL quick-change gun drill/reamer holders, designed and built by FL-Tool Holders, are available in
four different pilot type models.
The pilot model holder is used where radial positioning of the tool is required and provides a
guaranteed accuracy of .000050 T.I.R., one inch from the front face of the collet. The basic construction of
the gun drill/reamer assembly includes a Jacobs type beveled tooth nosepiece, a tapered collet and nut
assembly that securely clamps and unclamps the tool from the holder, and an internal flat that provides
positive drive for the tool.
In operation , counterclockwise rotation of a chU9k key wrench causes the beveled tooth nosepiece
to rotate in a counterclockwise direction. As the nosepiece turns, the internal collet and nut assembly
moves downward into the tapered end of the tool holder causing the collet to constrict and the tool to be
tightened along the entire length of the clamping surface. To unlock the chuck and remove the tool , a
simple clockwise rotation of the key wrench against the nosepiece is required .

FL-TOOL HOLDERS
Phone: 734-591-0134· Fax: 734-591-7866
SHRINK FIT STRAIGHT SHANK TOOL HOLDERS

• Patented
Shrink-Fit straight-shank tool holders can be used in The 10 of the shrink-fit straight-shank holder is slightly
existing automotive spindles where rigidity and smaller than the cutting tool shank diameter. A
concentricity are critical. Three separate sizes are heat induction unit is used to quickly heat the
available to accommodate tool shank diameters holder end of the shrinker, expanding the bore's
from .2500 (6 .35 mm) to .7500 (19 .05 mm) . All inside diameter. The tool shank then slips easily
tool shank diameters under .5000 (12 .70 mm) into the holder and as the holder cools, the result-
must be solid carbide . ing thermal contraction exerts tremendous, uni-
form pressure around the entire surface of the tool
The close fit of the holder 00 to the spindle 10 en- shank. No moving parts, no accessories, just total
ables accurate and sec ure positioning of the over- concentric gripping strength .
the-spindle adapter collar . Mounted over and ex-
isting spindle, the collar is rotated in a clockwise The average gripping force. imposed on the cut-
direction to mate with the Acme left-hand thread ting tool shank is 10,000 pounds, many times
on the collar, retaining the holder securely against greater than that of a collet, milling or hydraulic
the spindle face . This eliminates the rocking con- chuck . Concentricity of the straight-shank shrink-fit
d ition seen in all short taper designs . Counter- holder is .0003 with the cutting tool set in the
clockwise rotation of the collar forces the tool shrunk condition, extending tool life by up to 100%
holder body out of the spindle . or more.

SHRINK FIT STRAIGHT SHANK TOOL HOLDER SYSTEM
(C) MIN. CENTER DISTANCE
DIA . TOOL SHANK (MA X.) REF.
+.000
-. 002
(8) DIA. SPINDLE REF.
r .J8 TI1'. REF
SPINDLE
FACE REF. (E) DIA. REF.
LDCKSCR[W
5/'6 - 24 UNF
pr I 1I06 J - (
- 1.56 R[F.
S TANDARD
-
± .OO I
(0) R[F. --I
INCLUDED IN ASS'Y 1--_ (G) MIN,/ MAX, TOOL SET RANG[ _
DESIGN INFORMATION
A·TOOL SIZE A·TOOL SIZE B·MIN. C·MIN. CTR. G
SERIES
INCHES MILLIMETERS SPDL. DIA. DISTANCE
o REF . E REF. F REF.
MIN. MAX
10750 .2500 - .3750 6.350-9.525 1.315 1750 1.450 1.12 1.65 1.12 2.90
11063 .2500-.5000 6.350- 12.700 1.565 2.000 1.620 1.25 1.90 1.12 3.50
11375 .2500-. 7500 6.350- 19.050 2.065 2.500 1.750 1.50 2.40 1.12 4.10
Note: Full scale drawing templates are available for assistance in tool layouts, alterations or new
designs. Cad disk available upon request.
SPIN STRAIGHT SHANK

TOOL OLDER
PART NO.
SERIES OVER THE SPINDLE ADAPTER
TOOL HOLDER BODY
10750 10750·SF·E/MXXXX 10750·A

11063 11063·SF·E/MXXXX 11063·A
11375 11375·SF·E/MXXXX 11375·A
Tool Holder Ordering Information: Collar and Retaining Ring Ordering Information :
1) Locate desired tool holder series 1) Locate desired tool holder series
2) Specify English (E) or Metric (M) 2) Order by part number
3) Specify tool shank size (maximum)
Note: A +. 0000 / -. 0002 tolerance is recommended for
Example: 11063-SF-E.5000
tool shank dias. Shank taper should not exceed .0001 .
11 063-SF-M 12.70
FL-TOOL HOLDERS
36010 Industrial Road • Livonia, Michigan 481 50
Phone: 734-591-0134· Fax: 734-591-7866
SHRINK FIT TAPERED SHANK TOOL HOLDERS

• High Accuracy .Repeatabili1y
• Quick Changeabili1y
• Thru Coolant Capabili1y
• Patented
Shrink-Fit tapered tool holders are designed and The ID of the shrink-fit holder is slightly smaller than
built to improve product quality and tool life on the cutting tool shank diameter. A heat induction
production and non-production machines. The unit is used to quickly heat the holder end expand-
holders are available in five separate body sizes to ing the bore's inside diameter. The tool shank then
accommodate tool shank diameters from .2500 slips easily into the holder and as the holder cools,
(6 .35 mm) to 1.375 (34.92 mm). All tool shank di- the resulting thermal contraction exerts tremen-
ameters under .5000 (12.70 mm) must be solid dous, uniform pressure around the entire surface
carbide . of the tool shank. No moving parts, no accesso"
ries, just total concentric gripping strength .
Each patented shrink-fit holder features a precision
full-length tapered OD shank and a compact de-
sign to minimize spindle-to-spindle center distance The average gripping force imposed on the cut-
as well as overhang from the spindle end to the ting tool shank is 10,000 pounds, many times
bearing journal diameters. These features make , greater than that of a collet, milling or hydraulic
the shrink-fit tapered tool holder ideal for multiple chuck. Concentricity of the shrink-fit tapered
spindle applications where rigidity and concentric- holder is .0003 with the cutting tool set in the
ity are critical. shrunk condition, extending tool life by up to 100%
or more.
SHRINK FIT TAPERED TOOL HOLDER SYSTEM
(c) MIN . CENTER DISTAN CE
DIA. TOOL SHANK (MA X.) REF.
rJ8 ryP REF
r.---=~~--+---L--.
.1 '" , ------ --- -+----'----,
--4, - .;-- -
,
.;
'- - . -
'-<L .. --",,~_
± .OO I (E) DIA. REF.

( B) MIN. (D) REF.
SPINDLE DIA.
( H) MIN./MA X. TOOL
SET RANGE
DESIGN INFORMATION
A·TOOL SIZE A·TOOL SIZE B·MIN. C·MIN. CTR. H
SERIES
INCHES MILLIMETERS SPDL. DIA. DISTANCE
o REF. E REF. F REF. G REF.
MIN. MAX
2002 .2500 - .3750 6.350- 9.525 1.315 1750 1.450 1.12 1.65 1.06 1.12 2.90
3002 .2500-.5000 6.350-12.700 1.565 2.000 1.620 1.25 1.90 1.06 1.12 3.50
4002 .2500-.7500 6.350- 19.050 2.065 2.500 1.750 1.50 2.40 1.06 1.12 4.10
5002 .2500-1 .0000 6.350- 25.400 2.565 3.000 2.100 1.75 2.88 1.18 1.62 5.00
6002 .3750-1.3750 9.525- 34.925 3.060 3.500 2.260 2.12 3.38 1.18 1.62 5.80
Note: Full scale drawing templates are available for assistance in tool layouts, alterations or new
designs, Cad disk available upon request.
PART NO. SPINDLE COLLAR & RING
SERIES SPINDLE COLLAR
TOOL HOLDER BODY RETAIN. RING ASSEMBLY
2002 2002 ·SF·E/MXXXX 2002·C 2002·R 2002·CR

3002 3002·SF·E/MXXXX 3002·C 3002·R 3002·CR
4002 4002·SF·E/MXXXX 4002·C 4002·R 4002·CR
5002 5002·SF·E/MXXXX 500z.c 5002·R 5002·CR
6002 600t-SF·E/MXXXX 600z.c 6002·R 6002·CR
Tool Holder Ordering Information: Collar and Retaining Ring Ordering Information :
1) Locate desired tool holder series 1) Locate desired too l holde r series
2) Specify English (E) or Metric (M) 2) Order by part num ber
3) Specify tool shank size (maximum)
Example: 4002-SF-E ,5000 Note: A + .0000 / -.0002 tolerance is recommended for
tool shank dias. Shank taper should not exceed .0001 .
4002-SF-M 12,70

FL Tool Catalog

Uploaded by

Copyright:

Available Formats

FL Tool Catalog

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

FL Tool Catalog

Uploaded by

Copyright:

Available Formats

Back to Catalog Index

Quick Change Tapered Toolholders

Over.:rhe-Spindle Adapter AsselDblies

36010 Industrial Road - Livonia, Michigan 48150

AGC-377/94 Litho In USA

Tool Holder and Spindle Collar Assembly

-- holder assemblies and components

A·TOOL SIZE A·TOOL SIZE B·MIN. C·MIN. 0 E F G H

Collet and Nut Assembly

Tapered Tool Holder Assembly with Collet

SERIES PART NUMBER

Tapered Tool Holder Blank (Solid)

~ SERIES PART NUMBER A B

1002 1002·BLANK 1.00 .62

2002 2002·BLANK 1.25 .88

3002 3002·BLANK 1.38 1.06

4002 4002·BLANK 1.38 1.56

5002 5002·BLANK 1.50 2.12

SPINDLE POSITIVE DRIVE and

Quick-Change Tapered Body

3002 3002·B 1.250 11/2-12 1.375 3.56

4002 4002·B 1.750 2 -12 1.375 4.16

5002 5002·B 2.250 21/2 - 12 1.685 5.03

6002 6002·B 2.750 3 -12 1.850 5.85

Tool Holder Seal and Snap Ring

1000 1002·TS 1000 1002·TSR

3000 3002·TS 3000 3002·TSR

SIZE 4002 4002·N .696 2.02 11/2 - 12 1 3/4

Collet Snap Ring

SERIES PART NUMBER A·TOOL SIZE A·TOOL SIZE B C

NOTE: It is recommended that all tools

SERIES PART NUMBER A·TOOL SIZE A·TOOL SIZE A B C D E TANG

1002·0 .0625 - .1249 1.5875 - 3.1725 NO SLOT 5/64 --

1002·RWO .180·.200 4.57·5.08 5002·RWI .250·.260 6.35·6.60

1002·RWOA .201 ·.220 5.10·5.59 5002·RW2 .261·.300 6.63·7.62

2002·RWO .180·.200 4.57·5.08 5002·RW5 .381 ·.420 9.68· 10.67

Spindle Collar and Retaining Ring

Open End Spindle Wrench

Ordering Information 6002 600Z-WSP·S 12.00 2.86

Open End Spindle Collar Wrench

Ordering Information 6002 600Z·WSP 9.50 3.1 2

Socket Spindle Collar Wrench

Holding Adapter for Tool Change

Spindle Cleaning Swab

NOTE: These cleaning

Tool Setting Fixture ---.. CERTIFIED

3002 3002 -RTF

Tool Setting Fixture

CERTIFIED 5002 5002·TSF

Torque Wrench (3/8" Drive)

Crowsfoot for Collet Nut

SERIES PART NUMBER PART NUMBER PART NUMBER A

1002 752·1 752·1A N/A 3/4

XXXO & XXX1 SERIES USES A OCTAGON NUT

Snap Ring Pliers

PHONE: 734-591-0134· FAX: 734-591-7866

Straight Shank and Collet-Type Toolholders and

Over-The-Spindle Adapter Assemblies

Over-The-Spindle Adapter Assembly

Over-The-Spindle Adapter Assembly IL--_------'