Casing Scraper

Contents
Logan Casing Scraper Overview.................................................................... 2 Uses........................................................................... 2 Construction............................................................... 2 Operation. .................................................................. 2 . Maintenance............................................................... 2 Disassembly............................................................... 2 Assembly.................................................................... 3 Tool.Illustration........................................................... 3 Parts.List.................................................................... 5 Recommended.Tightening.Torques. .......................... 5 .

1. Logan Casing Scraper

Logan Casing Scraper

OVERVIEW Obstruction-free casing is critical for the efficient operation of many downhole tools during drilling, fishing, completion, or wireline jobs. The Logan Casing Scraper removes rust, scale, cement, mud, bullets, paraffin, perforation burrs and other obstructions or foreign material from the inside walls of casing. Logan Casing Scrapers are available to condition pipe ranging from 4-1/2 to 13-3/8 inches O.D. USES Maintaining a clean casing I.D. is important when operating drilling, fishing or wireline tools. Likewise, packers, patches, spears, and similar tools require clean surfaces to grip. Obstructions on casing walls frequently cause these tools to fail or become difficult to operate. The Logan Casing Scraper removes deposits, burrs, and irregularities from casing that might cause trouble during the operation of packers or other closetolerance equipment. Some of the main uses of the Logan Casing Scraper are to: 1. Clean out paraffin, hardened cement, and mud. 2. Remove burrs from perforations. 3. Remove imbedded bullets from casing. 4. Remove burrs and nicks caused by bits or fishing tools. 5. Remove tight spots in casing caused by dents from tool mishandling. CONSTRUCTION All Logan Casing scrapers are constructed with a single (1) scraper body, a (1) blade retainer, six (6) scraper blades with springs, two (2) retainer rings, a top and bottom retainer ring nut, and two (2) retainer ring set screws. The one-piece scraper body is rugged and easy to maintain. The splined body locks each blade into an integral part of the body to insure absolute safety and security. The Logan Casing Scraper has two (2) sets of three (3) blades. Each blade is constructed from high quality cast steel for excellent scraping characteristics and long-lasting durability. These six (6) scraper blades are designed to scrape over 360 of surface area. The scraper blades are designed with a long taper for passing through casing connections with minimal chance of hanging up. Each blade has a recessed pocket that holds the springs between the blade and the scraper body. These springs keep the blades firmly pressed against the pipe and allow the blades to compress and depress during scraping operations. The blades and springs are held in place on the scraper body with the blade retainer and two (2) retainer rings. A top and bottom retainer ring nut secures the retainer rings in position. Two (2) retainer nut set screws are used as a safety precaution to keep the top and bottom retainer rings locked in position. The top retainer ring nut is left-hand to prevent back off downhole during right-hand rotation should the set screws loosen during operation. OPERATION The Logan Casing Scraper is normally made up to the work string with a drill bit attached to the bottom connection. Simply run the scraper into the casing or tubing using rotation or spudding to clean the inside wall of the pipe. MAINTENANCE Good maintenance will ensure maximum life of the Logan Casing Scraper and prevent misruns. The tool should be completely disassembled and thoroughly cleaned after each use. Worn or damaged parts should be replaced during disassembly/assembly. DISASSEMBLY All disassembly and repairs should be conducted in a clean, well-equipped shop. 1. Place the Casing Scraper in a suitable vise. Clamp on either the box or pin end fishing neck. 2. With a suitable wrench, remove the two (2) set screws from the top and bottom retainer ring nuts.

CAUTION: The top retainer ring nut has a left-hand thread.

3. Remove the top retainer ring nut with a suitable wrench. NOTE: The top retainer ring nut is the nut that is on the pin end of the Casing Scraper. Stenciling on the nut indicates that it has a left-hand thread.

Logan Casing Scraper 2

Logan Casing Scraper

4. Arrange the Casing Scraper so two (2) of the blades are located on the bottom of the tool. With the aid of a looped strap and a suitable lifting device, such as an overhead crane or the arm of a forklift, pick up the strap to compress the blades and springs located on the bottom. Place a hand on the remaining top blade and slide the retainer ring back away from the blades. 5. Remove the top blade being careful not to lose the springs under the blade. Carefully lower the looped strap that is holding the two (2) bottom blades in place. Be careful not to lose the springs as the bottom blades are removed. 6. Remove the bottom retainer ring nut from the body. NOTE: The bottom retainer ring nut has right-hand threads. 7. Repeat steps 4 and 5 to remove the other three (3) blades. Thoroughly clean and inspect all parts. Replace any collapsed springs or those that have a weak recoil. Replace any blades that are chipped or severely worn. Tong and wrench marks should be filed smooth. ASSEMBLY The Logan Casing Scraper is easily assembled using standard shop tools. No special tools are required. Make sure all parts have been thoroughly cleaned and inspected prior to assembly. Have high quality thread compound and thick grease on hand. 1. Place the Casing Scraper body in a vise. Position the body so that two of the pockets for the blades are on the bottom. Clamp near one end. 2. Apply grease to the springs. NOTE: The grease will help the springs stay in place when they are inserted into the blades. 3. Place a blade with springs into the pocket on the body by slipping the lip of the blade under the blade retainer. 4. Slip a second blade with springs into the other pocket on the bottom. Tension on the looped strap may need to be adjusted to accomplish this. Pull tension on the looped strap with the lifting device until the blades and springs are compressed. 5. Place the third blade with spring in the pocket on top. 6. Grease the inside of the retainer ring and slide it over the end of the scraper blades. The top blade may have to be compressed slightly to position the ring in place. 7. Dope the threads on the body for the retainer ring nut with thread compound. Install the retainer ring nut and tighten sufficiently. NOTE: Remember, the top retainer ring nut has left-hand threads and the bottom retainer ring nut has right-hand threads. 8. Repeat steps 2 through 7 for the other end of the Casing Scraper body. 9. Install the two (2) set screws with thread compound and tighten. The Logan Casing Scraper is now ready for use.

3 Logan Casing Scraper

Logan Casing Scraper

Scraper Body

Top Retainer Ring Nut Top Retainer Ring Nut Set Screw Retainer Ring 2 required

Blades 6 required

Blade Retainer (Welded)

Bottom Retainer Ring Nut Set Screw Bottom Retainer Ring Nut

Logan Casing Scraper 4

Logan Casing Scraper

SIZE TO SCRAPE (O.D.) WEIGHT (LBS) 4-1/2 9.5 to 15.1 5 13.0 to 26.7 2-3/8 API Reg 3-5/8 508-361 AX800 AX2000 6 AX802 18 AX7000 AX8000 AX9000 2 P12004 2 5-1/2 14.0 to 23.0 7 17.0 to 38.0 9-5/8 32.2 to 64.9 10-3/4 13-3/8 32.75 to 73.2 48.0 to 98.0

CONNECTION TOOL O.D. COMPLETE ASSEMBLY Logan Part No. MANDREL BLADE SPRING TOP RETAINER RING NUT (LEFT-HAND THREAD) BOTTOM RETAINER RING NUT (RIGHT-HAND THREAD) RETAINER RING SET SCREW Logan Part No. Logan Part No. No. Reqd Logan Part No. No. Reqd Logan Part No. Logan Part No. Logan Part No. No. Req'd Logan Part No. No. Req'd

2-7/8 API Reg 4-1/2 508-450 AX10011 AX2001 6 AX40011 18 AX7001 AX8001 AX9001 2 P12004 2

3-1/2 API Reg 5-3/8 508-538 AX1002 AX2002 6 AX4000 30 AX7002 AX8002 AX9002 2 AX10002 2

4-1/2 API Reg 7-1/2 508-750 AX1003 AX2003 6 AX4003 30 AX7003 AX8003 AX9003 2 AX10002 2

6-5/8 API Reg 8-3/4 508-875 AX1004 AX2004 8 AX40013 24 AX7004 AX8004 AX9004 2 AX10002 2

6-5/8 API Reg 11 508-1100 AX1005 AX2005 6 AX4005 30 AX7005 AX8005 AX9005 2 AX10004 2

OPTIONAL DRESS FOR SIZE (O.D.) WEIGHT (LBS) BLADE Logan Part No. No. Reqd SPRING Logan Part No. No. Reqd

5-3/4 14 to 24.4 AX30012 6 AX40012 18

7-5/8 24 to 47.1 AX3002 6 AX4000 30

OPTIONAL DRESS FOR SIZE (O.D.) WEIGHT (LBS) BLADE Logan Part No. No. Reqd SPRING Logan Part No. No. Reqd

6-5/8 17 to 24 AX30013 6 AX40013 18

Logan Oil Tools reserves the right to change or discontinue designs and/or prices without notice. When ordering, please specify: (1) Name and number of assembly or part (2) Size and weight of casing Recommended Spare Parts: (1) 1 set of Blades for each size casing

RECOMMENDED TIGHTENING TORQUES COMPLETE ASSEMBLY Logan Part No. TOOL O.D. (IN) CASING SIZE (IN) TORQUE (FT-LBS) 508-361 3-5/8 4-1/2 to 5 350 508-450 508-538 508-750 7-1/2 9-5/8 750 508-875 8-3/4 ... 875 508-1100 11 13-3/8 1,100 4-1/2 5-3/8 5-1/2 to 6-5/8 7 to 7-5/8 450 550

5 Logan Casing Scraper

notes

Logan Casing Scraper. 6

HeadquarterS 11006 Lucerne Street Houston, TX 77016 Tel: (281) 219-6613 Fax: (281) 219-6638 sales@loganoiltools.com united StateS California 3155 Pegasus Bakersfield, CA 93308 Tel: (661) 387-1449 Fax: (661) 387-1624 Louisiana 103 Bluffwood Drive Broussard, LA 70518 Tel: (337) 839-2331 Fax: (337) 839-2334 118 Common Court Houma, LA 70360 Tel: (985) 868-7333 Fax: (985) 868-7007 Oklahoma 424 South Eagle Lane Oklahoma City, OK 73128 Tel: (405) 782-0625 Fax: (405) 782-0760 Mississippi 6 Donald Drive Laurel, MS 39440 Tel: (601) 649-0636 Fax: (601) 649-6909 texas 101 Commerce Street Alice, TX 78332 Tel: (361) 396-0139 Fax: (361) 396-0112 1305 Energy Drive Kilgore, TX 75662 Tel: (903) 984-6700 Fax: (903) 984-6755 1617 South Viceroy Odessa, TX 79763 Tel: (432) 580-7414 Fax: (432) 580-7656 utah 1369 South 1100 East Vernal, UT 84078 Tel: (435) 781-2856 Fax: (435) 781-2858 StOCking diStributOrS Canada Lee Oilfield Fishing Tools Ltd. 4604 Eleniak Road NW Edmonton, AB T6B2S1 Canada Tel: (780) 440-6705 Fax: (780) 463-5570 dubai Woodhouse International P.O. Box 23724 Dubai, UAE Tel: 971-4-347-2300 Fax: 971-4-347-4642 Scotland Smith Services, HE Group Howe Moss Avenue Dyce, Aberdeen Scotland AB21 OGP Tel: 44-1224-770707 Fax: 44-1224-724182

www.loganoiltools.com

2008 Logan Oil Tools 1M Rev. 0/0408