CI/SfB

(52.3)

In6

PRODUCT GUIDE

JANUARY 2001

Above Ground Drainage Systems

SOIL & VENT STACK

SOIL & VENT STACK

Push-Fit Pipes & Fittings

Material: PVC-U
Description Nom Cat

Push-Fit Pipes & Fittings continued

Kitemarked to B.S.4514
Description Nom Cat

(Frame Quantity 50)

3.0m 4.0m 2.5m 3.0m 4.0m 4.0m Pipe Single Socketed 2.0m 3.0m 4.0m 2.0m 2.5m 3.0m 4.0m 2.0m 3.0m 4.0m Double Socket Repair

Dia mm 82 82 110 110 110 160 82 82 82 110 110 110 110 160 160 160 82 110 110 160

No SP3PE/3 SP4PE/3 SP25PE SP3PE SP4PE SP4PE/6 SP2SS/3 SP3SS/3 SP4SS/3 SP2SS SP25SS SP3SS SP4SS SP2SS/6 SP3SS/6 SP4SS/6 S1/3 S1 S1A S1/6

Pack

Colour

2 2 2 2 2 1 2 2 2 2 2 2 2 2 2 2 10 10 10 1 10

Gr Gr Gr Bl Br Gr Bl Br Wh Gr Bl Br Wh Gr Gr Bl Gr Bl Gr Gr Bl Br Gr Bl Br Gr Bl Br Wh Gr Bl Br Wh Gr Gr Gr Gr Bl Gr Bl Br Wh Gr Bl Br Wh Gr Gr Bl Br Wh

Dia No mm Barrel Clip for use with 82 S11/3 drive-in spike (RP10) for xing soil pipe to masonry, brickwork or rendered buildings Barrel Clip 4 " 110 S11

Pack

Colour

10

Gr Bl

1 0

Gr Bl Br Wh

Barrel Clip Back Plate

(Frame Quantity 50)

Barrel Clip Back Plate Spacer Bend Solvent Socket Tail 871/2 671/2 45 871/2 671/2 45 Bend Spigot Tail 871/2 671/2 45 871/2 871/2 Tight radius 76 671/2 45 871/2 671/2 45

NEW NEW NEW

S115

1 0

Gr Bl Br Wh

S116

1 0

Gr Bl Br Wh

Double Socket Solvent 110 S121

82 82 82 110 110 110 82 82 82 110 110 110 110 110 160 160 160

S12/3STs S14/3STs S15/3STs S12STs S14STs S15STs S12/3 S14/3 S15/3 S12 S12TR S13 S14 S15 S12/6 S14/6 S15/6

5 5 5 5 5 5 10 10 10 10 10 10 10 10 1 1 1 10

Gr Gr Gr Gr Gr Gr Gr Gr Gr Gr Bl Br Wh Gr Bl Br Wh Gr Bl Br Gr Bl Br Gr Bl Br Wh Gr Gr Gr Gr Bl Br

Single Socket

82 S2/3 110 S2 160 S2/6 110 S4

10 10 1 10

Gr Bl Gr Bl Br Wh Gr Gr Bl Br

Drain Connector to clay socket Drain Connector to cast iron socket Shrink on Connector to cast iron and asbestos Seal rings for use with this tting Code No. S360/3, S360 and S360/6 Level Invert Reducer to 50mm to 82mm (Rubber) to 82mm to 110mm Reducers to 40mm Waste to 32mm Waste to 40mm Waste to 50mm Waste To Round downpipe To Square downpipe Pipe Fixing Bracket Quick Fix Quick Fix Pipe Fixing Bracket c/w Nut and Bolt Socket Fixing Bracket c/w Nut and Bolt Pipe or Socket Fixing Bracket Rust Protected

110 S4/A

10

Gr

82 S483 110 S484 160 S205/6

5 5 1

Gr Gr Gr

Access Bend Spigot Tail 110 S83 871/2

Top Offset Bend 45 82 110 110 160 82 110 110 110 110 110 82 110 160 110 S94/3 S93 S94 S94/6x4 S451s S440 S441 S442 S446 S448 S5/3 S5 S5/6 S7 10 5 5 1 5 5 5 5 5 5 10 10 10 10 Gr Gr Gr Gr Gr Gr Gr Gr Gr Bl Br Wh Bl Br Wh Gr Bl Gr Bl Br Wh Gr Gr Bl Br

82 S15A/3 110 S15A 160 S15A/6 82 S15B/3 110 S15B 160 S15B/6

10 10 1 10 10 1

Gr Gr Bl Br Wh Gr Gr Gr Bl Br Wh Gr

Bottom Offset Bend 45

Single Branch Solvent Socket Tail 871/2 - 2 Boss 871/2 - 4 Boss 671/2 - 2 Boss 45

82 110 110 110

S24/3STs S24AST S26STs S27STs S24/3 S26/3 S27/3 S24 S24A S25 S26 S27 S476 s S24/6 S24/6x4

5 5 5 5 5 5 5 5 5 5 5 5 5 1 1

Gr Gr Gr Gr Gr Gr Gr Gr Bl Br Wh Gr Bl Br Gr Bl Br Gr Bl Br Gr Bl Gr Gr Gr

110 S6

10

Gr Bl Br Wh

82 S8/3 110 S8 160 S8/6

10 10 10

Single Branch Spigot Tail 871/2 - 2 Boss 82 671/2 - 2 Boss 82 45 82 871/2 - 2 Boss 110 871/2 - 4 Boss 110 76 - 2 Boss 110 671/2 - 2 Boss 110 45 110 871/2 - with access to rear 110 871/2 - 2 Boss 160 871/2 - 2 Boss unequal 160 to 110mm

s not available ex-stock

Gr = Grey

Bl = Black

Br = Brown

Wh = White

SOIL & VENT STACK

SOIL & VENT STACK

Push-Fit Pipes & Fittings continued

Description Nom Cat

Push-Fit Pipes & Fittings continued

Colour Description Nom Cat

Dia mm

No

Pack

Single Branch 8 1 2- Top Boss 7/ ad2sd Bs n ie os

NEW

Access Pipe 110 S28 1 Gr

Dia No mm 82 S80/3 110 S80 160 S80/6 82 S81/3 110 S81 160 S81/6 110 S84

Pack

Colour

5 5 1 10 10 1 5

Gr Bl Gr Bl Br Wh Gr Gr Bl Gr Bl Br Wh Gr Gr

Double Branch Spigot Tail 871/2 - 2 Boss 45 871/2 - 2 Boss unequal to 110mm Double Corner Branch Spigot Tail 871/2

110 S40 110 S43 160 S40/6 110 S470

1 1 1 1

Gr Bl Br Wh Gr Gr Gr

Socket Plug Spigot Tail

Screwed Access Cap Spigot Tail Access Saddle Solvent

110 S82

Gr Bl Br

Single Boss Pipe Solvent Socket Tail for Push-Fit or Solvent Waste to 32mm 110 to 40mm 110 to 50mm 110 Single Boss Pipe Spigot Tail for Push-Fit or Solvent Waste to 32mm 82 to 40mm 82 to 50mm 82 to 32mm 110 to 40mm 110 to 50mm 110 Three Way Boss Pipe 82 Solvent Socket Tail 110 All bosses moulded solid

Weathering Collar S32STs S31STs S30STs 5 5 5 Gr Gr Gr Balloon Grating S32/3 S31/3 S30/3 S32 S31 S30 S33/3STs S33STs 5 5 5 5 5 5 5 5 Gr Gr Gr Gr Bl Br Wh Gr Bl Br Wh Gr Bl Br Wh Gr Gr

82 S85/3 110 S85

10 10

Gr Gr Bl Br Wh

82 S86/3 110 S86

10 10

Gr Gr Bl Br Wh

Extract Cowl

110 S87

Gr Bl

Air Admittance Valve 110 S203 * Solvent Socket for 110mm Pipe * Agrment Certicate No. 93/2916 Air Admittance Valve Spigot for 110mm or 82mm Pipe 110 S204 * for 110mm, 82mm or 50mm Pipe 110 S204/2 * * Agrment Certicate No. 86/1778 Flexible Vent Pipe Connects to ridge tile adaptor/110mm spigot Multipitch Roof Weathering Slate for 82mm & 110mm Soil Pipe 450mm square 450mm x 600mm 110 S206

Gr

Three Way Boss Pipe 82 S33/3 Spigot Tail 110 S33 All bosses moulded solid

5 5

Gr Bl Gr Bl Br Wh

1 1 1

Gr Gr Bl

Short Boss Pipe Solvent Sockets use with S420, S421, S422 Boss Adaptors Short Boss Pipe wt acs ih ces use with S420, S421, S422 Boss Adaptors

110 S35

Gr Bl Br Wh

110 S36

Gr Bl Br Wh

NEW

Boss Adaptor Rubber For Push-Fit or Solvent Waste Use with S35, S410, S412 32mm 110 S420 40mm 110 S421 50mm 110 S422 Six Way Boss Pipe Spigot Tail All bosses moulded solid 110 S34

S195 S196

5 5 1 1 1 50 Gr Bl Br Gr Gr

10 10 10 5

Bl Bl Bl Gr

Patch Boss For Push-Fit or Solvent Waste 32mm 82 40mm 82 50mm 82 50mm 110 50mm 160 Solvent Boss Adaptor For Push-Fit or Solvent Waste 32mm 110 40mm 110 50mm 110

Soil Manifold All inlets 32/40mm 110 S300/A* For 50mm connections use Inlet 1=50mm 2 & 3=32/40mm 110 S300/B* Inlet 3=50mm 1 & 2=32/40mm 110 S300/C* Inlet grommet 50 S352 Other inlet combinations available to special order * Agrment Certicate No. 86/1733 Floor Gully c/w stainless steel tile and grid for tiled oors 50mm Outlet 82mm Outlet Ancillary Items Stainless Steel Tile and Grid Trap Funnel Bowl Trap Extension Bowl Gully Extension Piece Gully Funnel Use Boss adaptors S420, S421, S422 Fire Protection Seal 50 82 110 160

S97/3 S96/3 S95/3 S95 S95/6 S101 S102 S103

10 10 10 10 1 10 10 10

Gr Gr Gr Gr Wh Gr Gr Bl Br Wh Gr Bl Br Wh Gr Bl Br Wh

S410 S412 S414 S415 S416 S417 S418

1 1 1 1 1 1 1

Gr Gr Gr Gr Gr Gr Gr

Clip Boss For Push-Fit or Solvent Waste 32mm 110 S105 40mm 110 S106 Strap Boss Use with S101, S102, S103 Boss Adaptors s not available ex-stock Gr = Grey Bl = Black

10 10 1 0

Gr Bl Br Wh Gr Bl Br Wh Gr Bl Br Wh

NEW
Br = Brown

110 S110

S500/2 S500/3 S500/4 S500/6

1 1 1 1

Red Red Red Red

Wh = White

SOIL & VENT STACK

SOIL & VENT STACK

Solvent-Weld Pipes & Fittings

Material: PVC-U
Description Nom Cat

Push-Fit W.C. Pan Connectors

Kitemarked to B.S.4514 Material: PVC-U
Description Nom

Kitemarked to B.S.4514
Pack Dia No mm 110 SP06PE/W 1 Cat Colour

Dia mm 82 82 82 110 110 110 110 160 160 160

No

Pack

Colour

(Frame Quantity 50)

Pipe Single Socketed 2.0m 3.0m 4.0m 2.0m 2.5m 3.0m 4.0m 2.0m 3.0m 4.0m Double Socket

SWP2SS/3 SWP3SS/3 SWP4SS/3 SWP2SS SWP25SS SWP3SS SWP4SS SWP2SS/6 SWP3SS/6 SWP4SS/6

2 2 2 2 2 2 2 2 2 2 10 10

Gr Bl Gr Bl Gr Gr Bl Gr Bl Gr Bl Gr Bl Gr Gr Gr Gr Bl Gr Bl

Pipe Plain Ended 0.6m Straight W.C. Connectors 150mm Projection 300mm Projection 450mm Projection 600mm Projection Straight Connector Solvent Socket

Wh

110 110 110 110

S61 s S63 S65 s S67 s

1 1 1 1 5

Wh Wh Wh Wh Wh

82 SW1/3 110 SW1

110 S210

Single Socket

82 SW2/3 110 SW2 160 SW2/6

10 10 1

Gr Bl Gr Bl Gr

Bent W.C. Connector Solvent Socket

110 S211

Wh

Level Invert Reducer to 82mm to 110mm Bend Spigot Tail 871/2 671/2 45 871/2 76 671/2 45 871/2 45

110 160

SW94 SW94/6x4

5 1

Gr Gr

Standard W.C. Dry Fixing Gasket to W.C. Spigot 102mm to 117mm Syphonic W.C. Dry Fixing Gasket to W.C. Spigot 89mm to 102mm Straight Polyex W.C. Connector to W.C. Spigot 95mm to 102mm 150mm Spigot 300mm Spigot 450mm Spigot 600mm Spigot 108mm to 117mm 300mm Spigot Bent Polyex W.C. Connector to W.C. Spigot 95mm to 102mm 871/2 150mm Spigot 871/2 600mm Spigot Straight Polyex Sleeve to W.C. Spigot 95mm - 102mm to W.C. Spigot 108mm - 117mm

110 S79

10

Wh

110 S79S

10

Wh

82 82 82 110 110 110 110 160 160

SW12/3 SW14/3 SW15/3 SW12 SW13 SW14 SW15 SW12/6 SW15/6 SW83

10 10 10 10 10 10 10 1 1 10

Gr Gr Gr Gr Bl Gr Bl Gr Bl Gr Bl Gr Gr Gr Bl

Access Bend Spigot Tail 110 871/2

110 110 110 110

WCA3S61P WCA3S63P WCA3S65P WCA3S67P

1 1 1 1 1

Wh Wh Wh Wh Wh

110 WCA1S63P

Top Offset Bend 45

82 110

SW15A/3 SW15A

10 10

Gr Gr Bl

110 WCA3S70P 110 WCA3S76P

1 1

Wh Wh

Single Branch Spigot Tail 871/2 - 2 Boss 671/2 - 2 Boss 871/2 - 2 Boss 76 - 2 Boss 671/2 - 2 Boss 45 871/2 - 2 Boss Double Branch Spigot Tail 871/2 - 2 Boss 45

110 WCA3 110 WCA1

20 20

Wh Wh

82 82 110 110 110 110 160

SW24/3 SW26/3 SW24 SW25 SW26 SW27 SW24/6

5 5 5 5 5 5 1

Gr Gr Gr Bl Gr Bl Gr Bl Gr Gr

Bent Horizontal Outlet W.C. Connector Spigot Tail for close coupled suite 90 110mm Spigot 110 S140 160mm Spigot 110 S140E Bent Horizontal Outlet W.C. Connector Double Socket 871/2 Bent Horizontal Outlet W.C. Connector to Cast Iron, Pitch Fibre and Asbestos Pipe 14 Straight Horizontal Outlet W.C. Connector Spigot Tail 21/2 Offset Straight Horizontal Outlet W.C. Connector Double Socket Fastfit Straight Connector 110 S150

1 1 1

Wh Wh Wh

110 110

SW40 s SW43 s SW33/3 SW33

1 1 5 5

Gr Gr Gr Bl Gr Bl

Three Way Boss Pipe 82 Spigot Tail 110 All bosses moulded solid Six Way Boss Pipe Spigot Tail All bosses moulded solid Access Pipe 110

110 S120

Wh

110 S130

Wh

SW34 s

Gr

110 S134

Wh

82 110 160

SW80/3 SW80 SW80/6

5 5 1

Gr Bl Gr Bl Gr

110 SPC101

10

Wh

Fastfit Offset Connector For standard items, clips, plain ended pipe etc. see Push-Fit Soil section pages 1 to 3. Expansion joints are catered for by the Hepworth Push-Fit Soil Range pages 1 to 3.

110 SPC102

10

Wh

s not available ex-stock

Gr = Grey

Bl = Black

Br = Brown

Wh = White 3

SOIL & VENT STACK

WASTE BRANCH

Push-Fit W.C. Pan Connectors continued

Material: PVC-U
Description Nom

Rigid Push-Fit Pipes & Fittings continued

Description Nom Cat

Kitemarked to B.S.4514
Cat Pack Colour

Dia No mm Fastfit 90 Bent Connector 110 SPC103

Bend 45

Dia mm 32 40 50

No BW10 CW10 DW10

Pack

Colour

10 10 10

Gr Bl Br Wh Gr Bl Br Wh Gr

Wh Spigot Bend 30 32 40 50 BW51 CW51 DW51 10 10 10 Gr Bl Br Wh Gr Bl Br Wh Gr

Fastfit Extension 250mm (10")

110 SPC104

10

Wh Knuckle Bend 90 32 40 50 32 40 50 BW11 CW11 DW11 BW12 CW12 DW12 10 10 10 10 10 10 Gr Bl Br Wh Gr Bl Br Wh Gr Gr Bl Br Wh Gr Bl Br Wh Gr

Fastfit Extension 450mm (18")

110 SPC105

10

Wh Bend 871/2

Fastfit Straight Connector 31/2" Spigot WC Manifold Connectors 88 Connector 13 Connector 18 Connector 23 Connector 28 Connector 32 Connector 37 Connector

110 SPC106

10

Wh

110 110 110 110 110 110 110

S160 S161 S162 S163 S164 S165 S166

1 1 1 1 1 1 1

Wh Wh Wh Wh Wh Wh Wh

Spigot Bend 871/2 Varix Socket

32 40 50 32 40 50

BW50 CW50 DW50 BW15 CW15 DW15

10 10 10 10 10 10

Gr Bl Br Wh Gr Bl Br Wh Gr Gr Bl Br Wh Gr Bl Br Wh Gr

Tee 871/2

The kitemark appears on products which have been endorsed as complying with the relevant British Standard. Full details of products carrying the Kitemark are available on request.

Access Plug

32 40 50 32 40 50

BW16 CW16 DW16 BW17 CW17 DW17

10 10 10 50 50 50

Gr Bl Br Wh Gr Bl Br Wh Gr Gr Bl Br Wh Gr Bl Br Wh Gr

Pipe Clip

WASTE BRANCH

Rigid Push-Fit Pipes & Fittings

Material: Polypropylene
Description Nom Cat

Kitemarked to B.S.5254 Dia mm 32 40 50 32 40 50 32 40 50 No BP3 CP3 DP3 BW1 CW1 DW1 BW1/V CW1/V DW1/V
Pack Colour

Anti-Syphon Valve Universal outlet Accepts imperial and metric copper, Push-Fit and Solvent-Weld plastics pipework

32 40

BW20 CW20

10 10

Gr Gr

Solvent-Weld Pipes & Fittings ABS

Material: ABS
Description Nom Cat

Pipe Plain Ended 3m

10 10 10 10 10 10 10 10 10

Gr Bl Br Wh Gr Bl Br Wh Gr Gr Bl Br Wh Gr Bl Br Wh Gr Gr Wh Gr Wh Gr

Kitemarked to B.S.5255 Dia mm 32 40 50 32 40 50 40 50 50 32 40 32 40 50 32 40 50 32 40 No SBP3 SCP3 SDP3 SBW1 SCW1 SDW1

Pack Colour

Straight Connector Double Varix Connector Accepts imperial and metric copper, Push-Fit and solvent weld plastics pipework Socket Reducer to overow ABS to overow ABS Socket Reducer 40mm to 32mm 50mm to 32mm 50mm to 40mm Tank Connector

Pipe Plain Ended 3m Straight Connector

10 10 10 10 10 10

Gr Bl Br Wh Gr Bl Br Wh Gr Bl Br Wh Gr Bl Br Wh Gr Bl Br Wh Gr Bl Br Wh

NEW

32 40

AO8 AO9

10 10

Gr Gr

Socket Reducer 40mm to 32mm 50mm to 32mm 50mm to 40mm Cap and Lining

SCBW2 10 Gr Bl Br Wh SDBW2 10 Gr Bl Br Wh SDCW2 10 Gr Bl Br Wh SBW5 SCW5 SBW6 SCW6 SDW6 SBW8 SCW8 SDW8 SBW19 SCW19 10 Wh 10 Wh 10 Gr Bl Br Wh 10 Gr Bl Br Wh 10 Gr Bl Br Wh 10 Gr Bl Br Wh Gg 10 Gr Bl Br Wh 10 Gr Bl Br Wh Gg 10 Gr Bl Br Wh 10 Gr Bl Br Wh

40 50 50 32 40 32 40

CBW2 DBW2 DCW2 BW4 CW4 BW5 CW5

10 10 10 10 10 10 10

Gr Bl Br Wh Gr Gr Gr Bl Gr Bl Wh Wh

Coupling Male Iron Tail Expansion Coupling Solvent Socket

Cap and Lining Socket

Cap and Lining Spigot

32 40

BW6 CW6

10 10

Wh Wh

Straight Adaptor Push-Fit to Solvent

Gr = Grey 4

Bl = Black

Br = Brown

Wh = White

Gg = Grey/Green

WASTE BRANCH

WASTE BRANCH

Solvent-Weld Pipes & Fittings ABS cont.

Material: ABS
Description Nom Cat

Solvent-Weld Pipes & Fittings MUPVC cont.

Material: MUPVC
Description Nom Cat Pack Colour

Kitemarked to B.S.5255 Dia mm 32 40 50 32 40 50 32 40 50 32 40 50 32 40 50 32 40 50 40 50 No SBW10 SCW10 SDW10 SBW11 SCW11 SDW11 SBW9 SCW9 SDW9 SBW12 SCW12 SDW12 SBW15 SCW15 SDW15 SBW13 SCW13 SDW13 SCW31 SDW31
Pack Colour

Bend 45

10 Gr Bl Br Wh 10 Gr Bl Br Wh 10 Gr Bl Br Wh 10 Gr Bl Br Wh 10 Gr Bl Br Wh 10 Gr Bl Br Wh 10 Gr Bl Br Wh 10 Gr Bl Br Wh 10 Gr Bl Br Wh 10 Gr Bl Br Wh 10 Gr Bl Br Wh 10 Gr Bl Br Wh 10 Gr Bl Br Wh 10 Gr Bl Br Wh 10 Gr Bl Br Wh

Bend 871/2

Dia mm 32 40 50 32 40 50 32 40 50

No

MBW12 10 Gr Bl Br Wh Gg MCW12 10 Gr Bl Br Wh Gg MDW12 10 Gr Wh Gg MBW15 10 Gr Bl Br Wh Gg MCW15 10 Gr Bl Br Wh Gg MDW15 10 Gr Wh Gg MBW13 10 Gr Wh Gg MCW13 10 Gr Wh Gg MDW13 10 Gr Wh Gg

Knuckle Bend 90

Tee 871/2

Spigot Bend 90

Tee 45

Bend 871/2

Cross Tee 871/2

40 50

MCW31 10 Gr Wh Gg MDW31 10 Gr Wh Gg

Tee 871/2

Overow Pipes & Fittings

Tee 45 10 Gr Bl Br Wh 10 Gr Bl Br Wh 10 Gr Bl Br Wh 10 Gr Bl Br Wh 10 Gr Bl Br Wh Material: Polypropylene (Push-Fit) and ABS (Solvent-Weld)
Description Nom Cat

Cross Tee 871/2

Dia mm 21.5 21.5

No

Pack

Colour

Pipe Plain Ended 3m Push-Fit Solvent Straight Connector Push-Fit Solvent Straight Tank Connector Push-Fit Solvent Bent Tank Connector Push-Fit 90 Solvent 90

AP3 SAP3

50 50

Gr Bl Br Wh Gr Bl Br Wh

Access Plug

32 40 50 50

SBW16 SCW16 SDW16 SDW30

10 Gr Bl Br Wh Gg 10 Gr Bl Br Wh Gg 10 Gr Bl Br Wh Gg 10 Gr Bl Br Wh

Caulking Bush

21.5 21.5

AO1 SAO1

50 50

Gr Wh Gr Wh

Pipe Clip

32 40 50

SBW17 SCW17 SDW17

50 Gr Bl Br Wh Gg 50 Gr Bl Br Wh Gg 50 Gr Bl Br Wh Gg

21.5 21.5 21.5 21.5

AO4 SAO4 AO5 SAO5

20 20 20 20

Gr Wh Gr Wh Gr Wh Gr Wh

Solvent-Weld Pipes & Fittings MUPVC

Material: MUPVC
Description Nom Cat

Pipe Plain Ended 3m

Dia mm 32 40 50 32 40 50 40 50 50 32 40 50 32 40 50 32 40 50

No MBP3 MCP3 MDP3 MBW1 MCW1 MDW1

Pack

Colour

Cap and Lining Push-Fit Solvent Reducer - ABS From 32mm Ps-i o Slet uhFt r ovn Weld Waste From 40mm Ps-i o Slet uhFt r ovn Weld Waste

21.5 21.5

AO6 SAO6

20 20

Gr Wh Gr Wh

10 Gr Bl Br Wh Gg 10 Gr Bl Br Wh Gg 10 Gr Wh Gg 10 Gr Bl Br Wh Gg 10 Gr Bl Br Wh Gg 10 Gr Wh Gg

Straight Connector

NEW

2. 15

AO8

1 0

Gr

2. 15 21.5 21.5

AO9 AO11 SAO11

1 0 50 50

Gr Gr Wh Gr Wh

Socket Reducer 40mm to 32mm 50mm to 32mm 50mm to 40mm Bend 45

MCBW2 10 Gr Bl Br Wh Gg MDBW2 10 Gr Bl Br Wh Gg MDCW2 10 Gr Wh Gg MBW10 10 Gr Bl Br Wh Gg MCW10 10 Gr Bl Br Wh Gg MDW10 10 Gr Wh Gg MBW11 10 Gr Bl Br Wh Gg MCW11 10 Gr Bl Br Wh Gg MDW11 10 Gr Wh Gg MBW9 MCW9 MDW9 10 Gr Bl Br Wh Gg 10 Gr Bl Br Wh Gg 10 Gr Wh Gg

Knuckle Bend 90 Push-Fit Solvent Bend 25 Push-Fit Solvent

21.5 21.5

AO12 SAO12

20 20

Gr Wh Gr Wh

Knuckle Bend 90

Tee 90 Push-Fit Solvent

21.5 21.5

AO15 SAO15

50 50

Gr Wh Gr Wh

Spigot Bend 90

Pipe Clip Push-Fit and Solvent

21.5

AO17

50

Gr Wh

Gr = Grey

Bl = Black

Br = Brown

Wh = White

Gg = Grey/Green 5

WASTE VALVES & WASTE TRAPS

WASTE VALVES & WASTE TRAPS

Water Seal Traps Push-Fit Varix Outlets

Material: Polypropylene
Description Nom Cat

Kitemarked to B.S.3943 Dia mm 32 40 32 40 40 No BS36 CS36 BT24 CT24 CT44

Pack Colour

Water Seal Traps Universal Compression Outlets cont.

Material: Polypropylene
Description Nom Cat

Tubular P Outlet Fixed 19mm shallow seal Tubular P Outlet Swivel 76mm seal Tubular P Outlet Swivel 76mm seal c/w cleaning eye Tubular P Outlet Swivel 76mm seal telescopic max 40mm extension Tubular Running Swivel 76mm seal

10 10 10 10 10

Wh Wh Wh Wh Wh

Dia mm Tubular P Outlet Swivel 40 76mm Seal Telescopic max. 40mm extension Tubular Running Swivel 76mm seal Tubular S Outlet Swivel 76mm seal Pedestal Trap F x d ie 76mm seal 40 50 32 40 3 2

No CT66

Pack

Colour

10

Wh

CT67 DT67 BT65 CT65 BT80

10 10 10 10 1 0

Wh Wh Wh Wh Wh

40

CT26

10

Wh

40

CT27

10

Wh

NEW

Tubular S Outlet Swivel 76mm seal Bottle P Outlet 38mm seal 76mm seal 38mm seal 76mm seal Bottle P Anti Syphon Barvac 76mm seal Washing Machine 76mm seal c/w 0.6m pipe Washing Machine Half Trap Swivel 76mm seal Plumbing Kit. 1 To Suit: Plumbing Kit. 1 11/2 or Plumbing Kit. 1 2 bowl Plumbing Kit. 2 To Suit: Plumbing Kit. 1 21/2 or Plumbing Kit. 1 3 bowl

32 40 32 32 40 40 32 40 40

BT25 CT25 BB30 BB31 CB30 CB31 BB35 CB35 CT50

10 10 10 10 10 10 10 10 5

Wh Wh Wh Wh Wh Wh Wh Wh Wh

Bottle P Outlet 38mm seal NEW 76mm seal 38mm seal NEW 76mm seal Bottle P Outlet 76mm seal Telescopic max 100mm extension Bottle P Anti-Syphon 76mm seal

3 2 4 0 3 2 4 0 40

BB70 BB71 CB70 CB71 CB72

1 0 1 0 1 0 1 0 10

Wh Wh Wh Wh Wh

40

CT51

10

Wh

Washing Machine Trap Kit 76mm seal c/w 0.6m pipe Washing Machine Half Trap Swivel 76mm seal

NEW

3 2 4 0

BB75 CB75

1 0 1 0

Wh Wh

40

CT60

Wh

40

FWK 1

Wh

40

CT61

10

Wh

40

FWK 2

Wh

Traps Ancillaries
Material: Polypropylene
Nom Cat

Kitemarked to B.S.5254 Dia mm 40 No CT40

Pack Colour

Water Seal Traps Universal Compression Outlets

Material: Polypropylene
Description Nom Cat

Description

Washing Machine Tee

10

Wh

Tubular P Outlet Fixed 19mm shallow seal Tubular P Outlet Lowline bath 30mm seal Bottle P Outlet Top entry shower Chrome waste 50mm seal Tubular P Outlet Swivel 76mm seal Tubular P Outlet Swivel 76mm seal c/w cleaning eye

Dia mm 32 40 4 0

No BS76 CS76 CS77

Pack

Colour

10 10 1 0

Wh Wh Wh

NEW NEW

Cap & Lining BSP Male Iron Tail Equal Ends 11/4"-32mm to 11/4"-32mm 32 Unequal Ends 11/4"-32mm to 11/2"-40mm 32 Equal Ends 11/2"-40mm to 11/2"-40mm 40 Unequal Ends 11/2"-40mm to 11/4"-32mm 40 Cap and Lining Socket 32 40 32 40 32 40

BW3/W 10 BW7/W 10 CW3/W 10 CW7/W 10 BW5 CW5 BW6 CW6 BW50 CW50 B/CC42 10 10 10 10 10 10 10

Wh Wh Wh Wh Wh Wh Wh Wh Wh Wh Wh

4 0

CB78

1 0

Wh Cap and Lining Spigot

32 40 40

BT64 CT64 CT84

10 10 10

Wh Wh Wh

Spigot Bend 871/2 Varifix Socket to convert P to S outlet Overow Rose & Hose c/w Chrome Face for connection to 1" BSP Cleaning Eyes

See Ancillary section page 7 for cement, cleaning uid and lubricant. Gr = Grey 6 Bl = Black Br = Brown Wh = White

Flexible Couplings, Adaptors & Fittings

Description

SOIL & WASTE PROBLEM SOLVERS

Nom Dia mm

Cat No

Colour

Hygienic Self Sealing Waste Valves

Material: P l p o y e e oyrpln
Description

Flexible Straight Coupling PVC

Colour: White

Universal Compression Outlet

Nom Dia Cat No Pack Colour

NEW NEW NEW

41-38 49-44 59-54 62-56

112-101 162-152

CF1 DF1 DF1A DF1B

SF1B S16 F/

B l B l B l B l
B l B l

WIMLAS Certicate No. 042/97 Hygienic Self Sealing Waste Valve

mm 3 2 4 0 BV1 CV1 1 0 1 0 Wh Wh

Flexible Adaptor Coupling PVC

49-44/41-38

DCF2
DF2A SF2 SF2A S26 F/ SF2B CF15 DF15 SF15

B l
B l B l B l B l B l B l B l B l

871/ Knuckle 2 Adaptor

3 2 4 0

BV11 CV11 BV3 CV3

1 0 1 0 1 0 1 0

Wh Wh Wh Wh

59-54/48-44 123-114/111-101 133-114/112-104 163-155/111/101 187-177/111-101 Flexible Tee PVC 48-41 63-54 116-105

3 2 Running Adaptor 4 0 Frisaln o ntlig i app rn n ie u

Flexible Elbow PVC

Rigid Push-Fit Pipes & Fittings

Description Nom Dia mm Cat No Pack Colour

Flexible Bush PVC Flexible Adaptor Coupling PVC

NEW NEW

48-41 63-54 116-105

CF12 DF12 SF12

B l B l B l

60-48 112-85 50-44/40-32 63-54/40-32 40-32 38-32/32-22

DCF9A SF9 DBF2 DF2A CBF2 BF2A

B l B l Gr Gr Gr Gr

Internal Drain Connector to waste pipe to 32/40mm waste pipe to 50mm waste pipe internal blanking plug Internal Drain Connector to 110mm soil

110 110 110 110

S460 S462 S89 S464

10 10 10 10

Bl Bl Bl Gr Bl

NEW
Soil & Waste
Description Replacement Soil Ring 82mm 110mm 160mm

SOIL & VENTILATING STACK

Nom

Cat

Dia mm
82 110 160

No

Pack

Colour

Vinyl Floor Gully c/w Grid and Clamp for vinyl sheet flooring 50mm Outlet 82mm Outlet

S360/3 S360 S360/6 SC03 SC04 SC05

20 20 20 50 50 50 50 50 50 1 1 1 1 1 1 1 Gr Bl Br Wh Gr Bl Br Wh Gr Bl Br Wh

S409 S411

1 1

Gr Be Gr Be

Retaining Clips 82 Retaining Clips 110 Retaining Clips 160 Manifold Seal 110 50

HepFlex Soil
Material: P l p o y e e oyrpln
Description

SC06 SC07 S352 S241 S242 S243 S247 S254 S256 S257

Colour: White

Universal Compression Outlet

N o m Cat Dia N o mm Pack Colour

Manifold Grommets Manifold Grommets Solvent Cement - 250ml can Solvent Cement - 75gm tube Solvent Cleaning Fluid - 250ml can Gap Filling Cement - 140gm tube Silicone Lubricant Grease - 125gm tub with screwed top Silicone Lubricant Applicator - 100gm concentrated silicone with sponge applicator Silicone Aerosol Lubricant - 400ml can

Flexible Pan Connector Long Flexible Pan Connector Sot hr

110

S170

Wh

110

S171

Wh

HepFlex Waste
Description Effective N o m Length Dia mm mm Cat No Pack Colour

WASTE BRANCH

Soil & Waste

Material: Polypropylene Kitemarked to B.S.5254
Nom Cat

Flexible Waste Pipe Smooth Bore

3 2 4 0 3 2 4 0

FBP3 FCP3 FBP6 FCP6

3m 3m 6m 6m

W W W W

h h h h

Description O Ring O Ring O Ring Retaining Clip Retaining Clip Retaining Clip O Ring - Varix O Ring - Varix Retaining Clip - Varix Retaining Clip - Varix Top Trap Washer Top Trap Washer Bottle Trap Bowl Washer (for BB30/31... CB30/31) (for Barvac) Back Nuts Back Nuts Compression Nut Back Nut

Dia mm
32 40 50 32 40 50 32 40 32 40 32 40 50 50 32 40 21.5 21.5

No
WA01 WA02 WA03 WA04 WA05 WA06 SC01 SC02 WA07 WA08 TA01 TA02 TA03 TA04 WA09 WA10 WA12 WA13

Pack 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50

Colour Wh Wh Wh Wh Wh Wh Wh Wh Wh Wh Wh Wh Wh Wh Wh Wh Wh Wh

Flexible Waste Connector Sio :Sio pgt pgt Fbiae lnt t arctd egh o 315 Push-Fit Waste 365 Fbiae lnt t arctd egh o 315 Solvent Weld Waste 365

3 2 4 0 3 2 4 0

FBW30 FCW30 FSBW30 FSCW30

1 1 1 1

W W W W

h h h h

Spigot Connectors To Push-Fit Waste To Solvent Weld Waste

3 2 4 0 3 2 4 0

FBW6 FCW6 FSBW6 FSCW6

1 0 1 0 1 0 1 0

W W W W

h h h h

Gr = Grey

Bl = Black

Be = Beige

Br = Brown

Wh = White 7

DOMESTIC

DOMESTIC

Clickt Half-Round Gutter & Fittings

Material: PVC-U
Description Nom Cat

Clickt Half-Round Downpipe & Fittings

Material: PVC-U
Description Nom Cat

Kitemarked to B.S.4576 Dia mm 76 112 112 No TG2 RG2 RG4

Pack Colour

Kitemarked to B.S.4576 Dia mm 50 50 68 68 68 68 110 No

Pack Colour

Gutter 2m 2m 4m

10 10 10

Gr Bl Gr Bl Br Wh Gr Bl Br Wh

Pipe Plain Ended 2m 3m 2m 2.5m 4m 5.5m Internal Drain Connector to round downpipe 68mm Pipe Connector

TP2 TP3 RP2 RP25 RP4 RP55 4A06B

5 5 5 5 5 5 10

Gr Bl Gr Bl Gr Bl Br Gr Bl Br Wh Gr Bl Br Wh Gr Bl Br Wh Bl

Floating Union

76 112

TG12 RG12

10 10

Gr Bl Gr Bl Br Wh

Gutter Support Bracket

76 112

TG13 RG13/3

10 10

Gr Bl Gr Bl Br Wh

50 68

TP22 RP22

10 10

Gr Bl Gr Bl Br Wh

Gutter Spacer Bracket

RG40

10

Bl Adaptor to Cast Iron and Asbestos Spigot to 68mm to 82mm

68 68

RP30 RP31

5 5

Gr Bl Br Wh Gr Bl Br Wh

Union Bracket

112

RG14

10

Gr Bl Br Wh Saddle Bracket For Pipe and Fittings 50 68 TP20 RP20 10 10 Gr Bl Gr Bl Br Wh

Stopend Outlet

76

TG15

10

Gr Bl

Running Outlet

76 112

TG16 RG16

10 10

Gr Bl Gr Bl Br Wh

Bend 671/2 671/2 871/2

50 68 68

TP16 RP16 RP16A

10 10 10

Gr Bl Gr Bl Br Wh Gr Bl Br Wh

Stopend - External

76 112

TG17 RG17

10 10

Gr Bl Gr Bl Br Wh

Single Branch - 671/2 68 RP21 10 Gr Bl Br Wh

Stopend - Internal Converts RG16 to stopend Outlet Angle 90 90 60 45

112

RG22

10

Gr Bl Br Wh Access Pipe 68 RP80 5 Gr Bl Br Wh

76 112 112 112 112

TG18 RG18 RG20 RG21

10 10 10 10

Gr Bl Gr Bl Br Wh Gr Bl Br Wh Gr Bl Br Wh Shoe 50 68 TP23 RP23 10 10 Gr Bl Gr Bl Br Wh

Captive Seal (New type) Adaptor to metal (half-round) to ogee Left Hand to ogee Right Hand to square HepRain Rise and Fall Rust protected

RG30/N 50

112 112 112 112

RG24 RG25 RG26 RG37 RG47

5 5 5 1 10

Gr Bl Br Gr Bl Br Gr Bl Br Bl Br Wh

Barrel Clip for use with drive-in spike (RP10) for xing downpipe to masonry, brickwork or rendered buildings Barrel Clip Back Plate

68

RP11 S115

10 1 0

Gr Bl Br Wh Gr Bl Br Wh

Top Rafter Bracket Rust protected Side Rafter Bracket Rust protected Top Rafter Bracket Rust protected Side Rafter Bracket Rust protected 112 112

RG48 RG49

10 10

Barrel Clip Back Plate Spacer

RG28 RG29

10 10

NEW NEW

S116

1 0

Gr Bl Br Wh

Drive-in Spike c/w nut & bolt Rust protected. Enables a variable stand-off between downpipe and wall

RP10

10

Gr = Grey 8

Bl = Black

Br = Brown

Wh = White

DOMESTIC

DOMESTIC

Clickt Square Gutter & Fittings

Material: PVC-U
Description Nom Cat Pack Colour

Clickt Square Downpipe & Fittings cont.

Material: PVC-U
Description Nom Cat Pack Colour

Dia mm 112 112

No

Dia mm 65 65 65

No

Gutter 2m 4m

SG2 SG4

5 5

Bl Br Wh Bl Br Wh

Pipe Plain Ended 2.5m 4.0m 5.5m

SP25 SP4 SP55

6 6 6

Bl Br Wh Bl Br Wh Bl Br Wh

Floating Union

112

SG12

10

Bl Br Wh

Internal Drain Connector to 65mm square downpipe

110

4A06C

10

Bl

Pipe Connector Gutter Support Bracket 112 SG13/3 10 Bl Br Wh Stand-off Bracket enables a 30mm stand-off between downpipe and wall Pipe Fixing Bracket

65

SP15

10

Bl Br Wh

65

SP20

10

Bl Br Wh

Gutter Spacer Bracket

RG40

10

Bl

65

SP14

10

Bl Br Wh

Union Bracket

112

SG14

10

Bl Br Wh Square to Round Adaptor 65 SP19 10 Bl Br Wh

Running Outlet

112

SG16

10

Bl Br Wh Bend 671/2 871/2 NEW 65 65 SP16 SP16A 10 10 Bl Br Wh Bl Br Wh

Stopend External

112

SG17

10

Bl Br Wh Mini Offset Eaves/Drain Connection 44mm projection 65 SP22 10 Bl Br Wh

Stopend Internal Converts SG16 to Stopend Outlet Angle 90 60 45

112

SG22

10

Bl Br Wh Single Branch 671/2 65 SP21 10 Bl Br Wh

112 112 112

SG18 SG20 SG21

10 5 5

Bl Br Wh Bl Br Wh Bl Br Wh Access Pipe 65 SP80 5 Bl Br Wh

Captive Seal Square-Section Rise and Fall Rust protected For use with gutter support bracket or union bracket

112

SG30/N

50

RG47

10

Shoe

65

SP17

10

Bl Br Wh

Top Rafter Bracket Rust protected Side Rafter Bracket Rust protected

RG48 RG49

10 10

Barrel Clip for use with drive-in spike (RP10) for xing downpipe to masonry, brickwork or rendered buildings Drive-in Spike c/w nut and bolt Rust protected. Enables a variable stand-off between downpipe and wall

65

SP11

10

Bl Br Wh

RP10

10

Top Rafter Bracket Rust protected Side Rafter Bracket Rust protected

112 112

SG28 SG29

10 10

The kitemark appears on products which have been endorsed as complying with the relevant British Standard. Full details of products carrying the Kitemark are available on request.

Gr = Grey

Bl = Black

Br = Brown

Wh = White 9

DOMESTIC

COMMERCIAL

Ogee Gutter & Fittings

Material: PVC-U
Description Nom Cat Pack Colour

Clickt High Capacity Gutter & Fittings

Material: PVC-U
Description Nom Cat Pack Colour

Dia mm 115

No

Dia mm

No

Gutter 4m

OG4

Bl Br Wh

Gutter 4m

75mm deep DG4

Gr Bl Br Wh

Gutter Support Bracket

115

OG13

10

Bl Br Wh Gutter Support Bracket 115mm wide DG13 75mm deep 10 Gr Bl Br Wh

Union Bracket

115

OG14

10

Bl Br Wh

Gutter Spacer Bracket

RG40

10

Bl

Running Outlet Square Downpipe

115

OG16

10

Bl Br Wh Union Bracket 115mm wide DG14 75mm deep 10 Gr Bl Br Wh

Stopend - Internal Right-hand Left-hand

115 115

OG22R OG22L

10 10

Bl Br Wh Bl Br Wh

Running Outlet

115mm wide DG16 75mm deep

10

Gr Bl Br Wh

Stopend - External Right-hand Left-hand Angle - Internal 90

115 115

OG17R OG17L

10 10

Bl Br Wh Bl Br Wh

Stopend External

115mm wide DG17 75mm deep

10

Gr Bl Br Wh

115

OG50

10

Bl Br Wh

Angle 90 45

115mm wide DG18 75mm deep DG21

10 10

Gr Bl Br Wh Gr Bl Br Wh

Angle - Internal 45

115

OG51

10

Bl Br Wh Captive Seal High Capacity DG30

Angle - External 90

115

OG20

10

Bl Br Wh Stopend Internal Converts DG16 to Stopend Outlet 115mm wide DG22 75mm deep 68mm to 65mm DP19 10 Bl Br Wh 10 Gr Bl Br Wh

Angle - External 45

115

OG21

10

Bl Br Wh Round to Square Adaptor Converts outlet to square rainwater pipe.

Adaptor to Ogee Half Round Gutter Right-hand Lf-ad ethn

115 115

OG25R OG25L

1 0 1 0

Bl Br Wh Bl Br Wh Rise and Fall Rust protected For use with gutter support bracket or union bracket RG47 10

Top Rafter Bracket Rust protected

RG48

10

Top Rafter Bracket Rust protected Side Rafter Bracket Rust protected Side Rafter Bracket Rust protected RG49 10 Top Rafter Bracket Rust protected Side Rafter Bracket Rust protected NOTE: Ogee gutter tting seals must be lubricated with silicone lubricant (S254, S256 or S257) prior to assembly.

RG48 RG49

10 10

DG28 DG29

10 10

For pipe and ttings 68mm Round and 65mm Square pages 8 and 9. Gr = Grey 10 Bl = Black Br = Brown Wh = White

COMMERCIAL

COMMERCIAL

Clickt Half-Round Gutter & Fittings

Material: PVC-U
Description Nom Cat

Roof Outlets & Hopper Heads

Description Nom Cat

Kitemarked to B.S.4576 Dia mm 150 No LG4

Pack Colour

Dia mm
82 110

No
S200/3 S200

Pack

Colour

Flat Roof Outlet Spigot Tail

1 1

Gr Gr

Gutter 4m

10

Gr Bl

Rainwater Hopper For: 68mm round down pipe 68 110mm round down pipe 110 160mm round down pipe 160 Rainwater Hopper For: 65mm square downpipe 65

RG19 LG19 LG19/6 s SG19

1 1 1 1

Gr Bl Br Wh Gr Bl Gr Bl Br Wh

Gutter Support Bracket

150

LG13

10

Gr Bl

Union Bracket

150

LG14

10

Gr Bl

SPECIALS
Stopend Outlet 150 LG15 10 Gr Bl

Half-Round Gutter Angles

Material: PVC-U Kitemarked to B.S.4576
Nom Cat

Running Outlet

150

LG16

10

Gr Bl

Description

Fabricated angles to order * Stopend - External 150 LG17 10 Gr Bl

Dia mm 112

No RGSPEC

Pack

Colour

Gr Bl Br Wh

Half-Round Downpipe Bends

Fabricated angles to order * Angle 90 150 LG18 10 Gr Bl 68 Gr Bl Br Wh

Square Gutter Angles

Shoe 110 S14A 10 Gr Material: PVC-U
Description Nom Cat

Fabricated angles to order * Rise and Fall Rust protected 150 LG27 10

Dia mm 112

No SGSPEC

Pack

Colour

Bl Br Wh

Square Downpipe Bends

Fabricated angles to order * Top Rafter Bracket Rust protected 150 LG28 10 65 Bl Br Wh

High Capacity Gutter Angles

Side Rafter Bracket Rust protected For use with gutter support bracket or union bracket 150 LG29 10 Material: PVC-U
Description

Fabricated angles to order *

Dia No Pack mm 115mm x 75mm DGSPEC

Nom

Cat

Colour

Bl Br Wh

Ogee Gutter Angles

Fabricated angles to order * 115mm OGSPEC Bl Br Wh

Gr = Grey Bl = Black s not available ex-stock

Br = Brown

Wh = White

* To order telephone Technical Support: 01709 856406

11

Product Data
Description Hepworth Plumbing Waste Systems are manufactured in 32mm, 40mm and 50mm nominal sizes in polypropylene (PP), acrylonitrile butadiene styrene (ABS) and modified unplasticised PVC (MUPVC). A significant feature of the Hepworth System is the patented Push-Fit jointing method. An O ring seal is retained in a moulded housing by a snap-in end clip. This gives a simple, positive Push-Fit sealing action and incorporates an allowance for thermal movement of the pipework at each joint. This joint is also available in a Push-Fit Varix form. The Push-Fit Varix socket accepts Push-Fit Solvent-Weld pipework, metric and imperial copper pipe. Alternatively the solvent jointing method makes these systems particularly suited to prefabrication. Socket Detail
P/P Pipe

Dimensions
Nominal size mm Wall thickness (min) Length Mean Weight 32mm pipe = 40mm pipe = 50mm pipe = 32 1.80 3m Push-Fit (P/P) 0.185 Kg/m: 0.232 Kg/m: 0.326 Kg/m: 40 1.90 50 2.00

3m 3m Solvent Weld (ABS) (MUPVC) 0.227 Kg/m 0.300 Kg/m 0.277 Kg/m 0.386 Kg/m 0.400 Kg/m 0.540 Kg/m

Thermal Movement
Push-Fit (P/P) Linear Expansion Coefficient 10-4/C 1.2 (ABS) 0.5 Solvent-Weld (MUPVC) 0.5

P/P Retaining Clip O Ring Seal P/P Pipe Socket

Effect of Solar Radiation Polypropylene is affected by ultra-violet light and the painting of external pipework only is recommended. The performance of ABS and MUPVC waste systems is unaffected by solar radiation. The painting of external pipework, however, is recommended to give protection against the discolouring effects of strong sunlight. Effect of Frost Frost does not affect the operation of the systems; sub-zero temperatures, however, reduce the impact strength. Flammability Test method BS 2782 Method 508A.
Push-Fit (P/P) 1.0''/min (ABS) 1.3''/min Solvent-Weld (MUPVC) Self Extinguishing

Application To provide an efficient means of drainage of waste water, to either a gully or soil stack, from single or multi-storey buildings. Standards Hepworth Building Products Waste Systems, where applicable, conform to the standards laid down by BS 5254 and BS 5255 and are entitled to carry the Kitemark. Ring seals comply with BS 2494. Quality Assurance All products manufactured by Hepworth have to pass our stringent quality control procedures. A substantial majority also satisfy continuous assessment schemes operated by the British Standards Institution and are entitled to carry the Kitemark. Products which bear a British Standard number have been made in accordance with the appropriate specifications. Where no relevant British Standards exist products are manufactured to our own high standards. Composition and Manufacture Push-Fit Waste pipe is extruded in polypropylene, pipe fittings are injection moulded in polypropylene. O ring seals are moulded from specially formulated synthetic rubber. Solvent-Weld Waste pipe is extruded in ABS (Acrylonitrile Butadiene Styrene), pipe fittings are injection moulded in ABS, or waste pipe is extruded in MUPVC, pipe fittings are injection moulded in MUPVC. Effect of Chemicals Polypropylene has a high chemical resistance and is unaffected by boiling water. It is resistant to most organic acids, alkalis and aqueous solutions though subject to attack by oxidising acids and concentrates. ABS is resistant to most organic acids, alkalis and aqueous solutions although subject to attack by some inorganic acids and concentrates. MUPVC is specifically formulated to be resistant to boiling water and is also resistant to the majority of inorganic acids and alkalis. MUPVC will not support combustion. For specialised applications, consult our Technical Support Hotline: Tel: 01709 856406 Fax: 01709 856407. Colour Push-Fit (32 and 40mm) and ABS Solvent-Weld available in white, grey, black and brown. Push-Fit 50mm available in grey only. MUPVC Solvent-Weld available in white and grey.

Maintenance Designers should provide adequate access for periodic cleaning. It is advisable to paint pipes fixed externally for protection against the effects of strong sunlight. Traps Description Traps are manufactured in white polypropylene in 32mm and 40mm nominal sizes, for connection to 32mm and 40mm BSP standard waste outlets. The range includes tubular bottle, swivel neck, and anti-syphon types. Traps are supplied with washers to BS 2494. Trap Outlets A choice of either Push-Fit Varifix outlet or universal compression outlet is available. Both will accept Push-Fit or Solvent-Weld plastics pipe work to BS 5254 or BS 5255 and imperial or British metric copper. Varifix traps can be supplied with outlets for connection to 40mm ISO metric pipe. Performance The traps are manufactured to meet all the requirements of BS 3943 and carry the kitemark where applicable. All Hepworth traps have seals to the requirements of BS 2494. Barvac Trap Anti-syphon trap for automatic protection from syphonage problems associated with waste discharge systems. The trap is self-cleaning, has no moving parts and has a flow rate in excess of that required by BS 3943. Special design features give high flow rates and the bowl is removable for easy access and cleaning. 32mm: 50 litres/minute. 40mm: 67 litres/minute. Normal deep seal: 85mm. Minimum seal possible after syphonage (extreme conditions): 40mm.

12

Product Data
Description Hepworth Plumbing Soil and Ventilation Systems are manufactured in 82mm, 110mm and 160mm sizes in PVC-U (unplasticised polyvinyl chloride). The systems are available with either push-t or solvent-weld joints. Application To provide an efficient means of drainage of waste water and foul discharge from appliances in single and multi-storey buildings. Push-Fit Soil The Push-Fit joints allow for the expansion of pipes and incorporate a unique, patented purpose designed sealing method with double location lock. A sealing ring is contained in a moulded housing designed to prevent displacement either during installation or as a result of the action of expansion and contraction. Soil Socket Detail Patented clip Captive ring seal Expansion allowance 10mm for lengths up to 4m Ring seals are manufactured from SBR synthetic rubber to BS 2494. Thermal Movement Coefficient of linear expansion for PVC-U is 0.5 x 10 -4/C temperature rise ie: 1mm per 2m length for a temperature rise of 10C. Push-Fit Jointing An allowance is made for the expansion of pipes and ttings in each socket. Solvent-Weld Jointing Expansion is allowed for by the use of push-t ttings at relevant points in the system, in accordance with BS 5572, Code of Practice for Sanitary Pipework. Effect of Solar Radiation Prolonged exposure to sunlight will cause the colours to fade. It may also result in the slight loss of impact strength. It is not expected that this would affect the performance of the system. Protection may be gained by painting. Most exterior gloss paints are suitable for this purpose. Effect of Frost Frost does not affect the performance of PVC-U. However, impact strength is reduced at sub-zero temperatures. Care should be taken when installations are undertaken at these temperatures. Flammability PVC-U is self-extinguishing as dened by BS 2782: Method 508A. Chemical Resistance PVC-U is resistant to most acids, alkalis and oils. BS code of practice 312 Part 1, gives comprehensive information on the chemical resistance of PVC-U and should be consulted in case of doubt. Additional information can be obtained from: Technical Support Hotline Tel: 01709 856406 Fax: 01709 856407. Maintenance Designers should provide adequate access for periodic cleaning. Access pipes and bosses are available within both ranges. Adaptation to 40mm and 50mm ISO Metric OD Pipe All Hepworth nominal 40mm and 50mm bossed ttings and solvent boss adaptors can be supplied to accept 40mm or 50mm ISO metric waste pipes. Special Fabrications For particular installations that require special products, a fabrication service is available. Information on this service is available through the Technical Support Hotline Tel: 01709 856406 Fax: 01709 856407. Colours Push-Fit Soil
Nominal size mm Grey Black Brown White * Selected Items Only 82mm * 110mm * * 160mm

Solvent-Weld Soil
Nominal size mm Grey Black * Selected Items Only 82mm * 110mm * 160mm

Solvent-Weld Soil The use of Solvent-Weld joints enables on-site construction, or prefabrication, which may be undertaken on or off site. Solvent-Weld soil is available in a variety of colours to complement its surroundings. Both these lightweight soil systems are simple to install and are maintenance free. Composition and Manufacture Soil pipe is extruded in PVC-U. Both Push-Fit and Solvent-Weld soil ttings are injection moulded in PVC-U. Pipe Dimensions
Nominal size mm Actual minimum O.D. Lengths - metres Single Socket pipe 82mm 82.40 2.0 3.0 4.0 Plain Ended pipe 3.0 4.0 110mm 110.0 2.0 2.5 3.0 4.0 2.5 3.0 4.0 160mm 160.0 2.0 3.0 4.0

4.0

Weight
82mm pipe 110mm pipe 160mm pipe = 1.3 Kg/m: (mean) = 1.59 Kg/m: (mean) = 2.40 Kg/m: (mean)

13

Design
Design Recommendations for Single Stack Plumbing
Trap Depth of Seal Height of Appliance Height of Trap Outlet Angle of Outlet Pipe Minimum size Maximum Length Recommended Fall Connection to Main Stack Notes Bath P Minimum 75mm 0.622m 140mm 21/2 40mm 3m Between 1 and 5 No connection within area 200mm below intersection of centre lines of branch Flat bottom tends to trickle ll trap Wash basin P Minimum 75mm 0.787m 521mm 21/2 32mm 1.7m Between 1 and 5 Sink P Minimum 75mm 0.900m 546mm 21/2 40mm 3m Between 1 and 5 Preferably via Boss Pipe with expansion joint With exception of heights this data can be used for bidet Flat bottom tends to trickle fill trap W.C. S or P Minimum 50mm 0.406m 190mm 75mm & 102mm 6m Minimum 1 Branch should have a swept entry 75mm usual syphonic

Discharge unit values and ow rates for common appliances

Type of appliance W.C. (9 litres) Frequency of use minimum 20 10 5 20 10 5 Spray tap basin* Bath Shower Washing machine (automatic) Sink Add 0.06 litre/s per tap 75 (domestic) 30 (commercial and congested) Add 0.1litre/s per spray 250 20 10 5 20 (commercial and congested) Discharge units 7 14 28 1 3 6

Maximum number of discharge units allowed on branch discharge pipes

Discharge Units Size mm 32 40 50 65 75 90 100 125 150 Gradient 1/2 (9mm/m) 120 230 780 2000 11/4 (22mm/m) 1 2 10 35 100 230 430 1500 3500 21/2 (45mm/m) 1 8 26 95 230 460 1050 3000 7500

Wash basin

7 18 4 6 14 27 0.3

Note 1: Maximum number of discharge units permitted on a 150mm vertical stack is 5500. Note 2: Discharge pipes sized in this way give minimum size necessary to carry expected flow load. Note 3: Ventilating pipes may be required and sizes are shown below.

Urinal (per person) One group consisting of one W.C., one bath, one or two basins and one sink

14

* Some proportion of total may be assumed to be in simultaneous operation if considered appropriate. Frequency of flushing of automatic flushing cistern. Note: Unless otherwise stated, frequencies given above represent: 20 min corresponds to peak domestic use. 10 min corresponds to peak commercial use. 05 min corresponds to congested use in public toilets, schools, etc.

General guide for sizes of ventilating pipes and stacks

Size of branch discharge pipe or discharge stack (D) Smaller than 75mm 75mm and above Size of branch ventilating pipe or stack 2/3 D (25mm min.) 1/2 D

Maximum capacity and number of discharge units for vertical stacks

Size mm 50 65 75 90 100 125 150 Approximate capacity of stack, l/s 1.2 2.1 3.4 5.3 7.2 13.3 22.7 Approximate number of discharge units 10 * 60 * 200 350 750 2500 5500

Table of Pipe Dimensions

Nom. size 21.5 21.5 32 40 50 32 40 50 82 110 160 Systems Overflow Push-Fit Overflow Solvent Push-Fit Waste Push-Fit Waste Push-Fit Waste Solvent Waste Solvent Waste Solvent Waste Soil Soil Soil Mean O.D. mm 21.56 21.56 34.6 41.0 54.1 36.3 42.9 55.9 82.6 110.2 160.3 Mean I.D. mm 19.2 19.2 30.6 36.8 49.7 32.2 38.7 51.5 76.0 103.6 153.5

* No W.C.s. Not more than one siphonic W.C. with a 75mm outlet. Note: Ventilating stacks may be required and sizes are shown opposite.

14

Sitework
Jointing Push-Fit Systems Ensure the pipe is cut square and chamfered prior to assembly with fittings. Lubricate the pipe and fitting with Silicone Lubricant S254 and push-t to the full socket depth. Withdraw the pipe 5mm on the waste system and 10mm on the soil system to allow for expansion. Soil fittings with spigot ends should be inserted into the sockets to depth marks engraved on the spigot. This procedure automatically allows for expansion. Anchor fittings with a socket bracket to maintain expansion allowance. No expansion need be allowed for on the Push-Fit overflow system. Solvent-Weld Systems Ensure the pipe is cut square before assembly with fittings. Use Cleaning Fluid S243 on both surfaces to be joined. This removes all dirt and machine release agents and softens the surface ready for the chemical solvent-weld. Failure to do this can result in joint failure. Apply Solvent Cement S241/2 evenly over mating surfaces of both pipe and socket. Insert the pipe into the socket with a slight twisting action to the full socket depth. Surplus cement should be removed with a cloth. The joint should be firm enough to handle in 5 minutes. Please observe the safety precautions detailed on each can of solvent cement. Note: There is a small gap between the O.D. of the pipe and the I.D. of the fitting. This is to allow sufficient solvent cement into the joint to make a good weld. Expansion of the pipework should be allowed for by incorporating expansion couplings at predetermined lengths in long pipe runs. The pipe run should be clipped adjacent to the expansion couplings. No expansion need be allowed for on the Solvent-Weld overflow system. Traps When jointing traps to waste outlets, use the washer supplied, do not over tighten the nut (hand tight plus 1/8 turn). No other jointing compound or materials should be used. P traps can be converted to S pattern by means of BW50 and CW50 conversion bends. Traps are available with either Push-Fit or compression outlets as previously described. All traps are provided with a means of access where required. Support of pipework The table below shows the recommended maximum centres for support of pipework.
Soil Horizontal Vertical 1.00m 2.00m Waste 0.75m 1.50m Overflow 0.75m 1.50m

Drain Connections
From 100mm SuperSleve Internal External 82mm Soil 110mm Soil 32mm Waste 40mm Waste 50mm Waste 68mm Round Downpipe 65mm Square Downpipe S464# S460# S460# S462# 4A06B# 4A06C# SA8* 4A18A or SA9* SA4* SA5* SA6* SA7* or SA11* SA11* To 110mm PlastiDrain Internal External S464P# S460P# S460P# S462P# 4A06R# 4A06S# 4P11A Sl or 4P02A 4A03A 4A04A 4A05A 4A06A 4A07U

* = SuperSleve Code # = Will t inside any nominal 100mm pipe

Waste Pipe Connection A range of solvent-on bosses with Push-Fit joints allow connections of the waste pipe systems to the stack. (a) Soil Bosses S101, S102 and S103: Soil fittings are provided with shoulders to accept soil bosses. Drill out the centre of the shoulder and attach using solvent cement. (b) Clip Bosses and Patch Bosses S105, S106 and S95: Allows waste pipe connection to soil pipe. Drill the pipe where required and solventweld the boss in position. (c) Boss Adaptors, S420, S421, S422: Are for use with the S35 solvent three way short boss pipe, or the S410, S412 deep seal floor gully only. Recommended Hole Cutter Diameter
Cat. No. S101 S102 S103 S105 S106 S95 S95/3 S96/3 S97/3 S420 S421 S422 Cutter Dia. 60 60 60 38 45 67 57 57 57 60 60 60

Metric W.C. Connection A range of horizontal outlet pan connectors is available for fixing to metric pans as specified in BS 5503. These are supplied with an integral sealing diaphragm which allows for up to 5 misalignment in any direction. Imperial W.C. Connection A range of pan connectors is available to meet the varying pan spigot outside diameters. These are Push-Fit connections, allowing easy removal in the event of the W.C. pan becoming defective at a later date. The polyflex pan connector is particularly adaptable because it allows for up to 5 misalignment in any direction. Shrink-on Connection Fit a replacement soil ring (S360/3 or S360) onto the cast iron pipe spigot i.e. flat edge towards the pipe. Fit the blown socket of the shrink-on connector over the seal and apply gentle heat until the socket shrinks onto the cast iron pipe. This will compress the ring and form a watertight seal. The cast iron spigot should have a relatively smooth surface before making the joint. Roof Weathering The Multipitch Roof Weathering Slate has been designed to provide an easy and effective seal between either 82.4mm or 110mm soil pipes. It is suitable for use on a variety of roof pitches from 10 to 55 and is capable of being utilised on the most severe roof-tile profiles.

Fix clips and brackets using rust-proofed countersunk screws. Use No. 8s on waste and overflow systems and No. 10s on soil system. Soil System Installation Mark the position of brackets, drill and screw fix prior to erecting the stack. Start from the base of the stack and work up. Use S5 or S7 pipe brackets in conjunction with S6 socket brackets. On multi-storey installations, use S8 rust protected metal brackets on both the pipe and sockets. Drain Connection (a) Connections to Salt Glazed and Unjointed Clay The S4 is used to connect to old clay underground drainage systems. Using a sand and cement compound, cement S4 into the clay collar ensuring that the top of the connector is above floor level to allow expansion of the pipework. (b) Connections to Cast Iron The S4A is designed to connect to cast iron underground drainage systems. Use gaskin in the bottom third of the cast iron socket and make the joint using cold caulking compound such as PC4.

15

Clickt Half-Round Rainwater - Clickt Square Rainwater Clickt High Capacity Rainwater - Ogee Rainwater

Product Data - Design - Sitework

Description Hepworth Plumbing Rainwater Systems are available in three profiles; Half Round, Square and High Capacity. The systems are manufactured from PVC-U, and incorporate synthetic rubber seals for maximum joint security. Clickfit Half Round Rainwater is a domestic rainwater system with nominal half round gutters of 112mm and 50mm and 68mm circular downpipes. Clickfit Square Rainwater is a more aesthetically appealing domestic profile with 112mm gutters and 65mm square downpipes. High Capacity Rainwater has been designed for large roofed domestic buildings and small commercial units where aesthetic appearance is important. High Capacity has approximately half-elliptical gutter 115mm nominal diameter by 75mm deep. It can be used with 68mm round or 65mm square downpipe. Ogee Rainwater is a decorative profile, with a high flow capacity. It is suitable for new build and refurbishment projects, where a more aesthetically appealing profile is required. It can be used with Square downpipe, or Round downpipe with an adaptor. Application To provide an efficient means of collection and drainage of rainwater from pitched roofs into the below ground drainage system. Standards Clickfit Half Round Rainwater is manufactured to BS 4576: Part 1: 1989 Specification for Unplasticised PVC Rainwater Goods and is kitemarked accordingly. There is no British Standard for Square Section Rainwater Systems. Hepworth Plumbing manufacture Clickfit Square Rainwater at a site certified to BS 5750 and ISO 9002. Colour Clickfit Half Round is available in grey, black, brown and white. Clickt Square Rainwater is available in black, brown and white. High Capacity Rainwater is available in grey, black and brown. Ogee Rainwater is available in black, brown and white. Maintenance Hepworth Plumbing Rainwater Systems are resistant to the effects of exposure to sunlight and to the corrosive atmospheres found in industrial and coastal areas. Low temperatures will not affect the performance of the system, but the systems resistance to impact loading will be reduced at sub-zero temperatures, and additional care in handling is recommended. The effects of expansion and contraction can result in gutter noise under certain conditions. This can be alleviated by the application of silicone lubricant to the gutter seals. Special Fabrications For particular installations that require special products a fabrication service is available. Information on this is available through the Technical Support Hotline: Tel: 01709 856406 Fax: 01709 856407. Recommended Gutter Size Requirements To specify the gutter size, two factors must be taken into consideration: 1. The effective maximum roof area to be drained. 2. The gutter flow capacity. Effective Roof Area The effective roof area can be calculated by using the following formula: effective roof B + C x length of roof = 2 area in m2 Gutter Flow Capacity Gutter flow capacity is dependent upon three factors: 1. System type. 2. Outlet position. 3. Whether gutter is laid level or to a specified fall. The information in Table No. 1 calculates the correct gutter flow capacity for a specified system profile, outlet position and fall. This information has been based on a rainfall intensity of 75mm per hour and recommendations from BS 6367: 1983. Recommended Gutter Support Spacings Gutter support brackets for Half Round and Square section systems should be fixed at maximum 1000mm centres in normal weather conditions. In abnormal weather conditions such as regular heavy snowfall, BS 6367: 1983 recommends the use of snow boards to avoid gutters becoming blocked or over-laden. As a precautionary measure against the weight of snow the maximum spacings should be reduced to 750mm. High Capacity brackets and fittings with integral screw mountings (i.e. union bracket and running outlet) can be fixed at maximum 1200mm centres in normal weather conditions or at 900mm centres as a precaution against the weight of snow. Table No.1 Gutter Flow Capacity Outlet at end of gutter run
Gutter Flow Capacity (litres per second) System Profile 76mm Half Round 112mm Half Round - Clickfit 112mm Square Section 150mm Half Round 115mm High Capacity Ogee Gutter level 0.27 0.83 1.08 1.83 2.05 2.34 1: 600 Fall 0.38 1.17 1.52 2.56 2.87 2.50 Maximum Roof Area (square metres) Gutter level 16 40 52 88 98 112 1: 600 Fall 23 56 72 123 137 122

Outlet at centre of gutter run

76mm Half Round 112mm Half Round 112mm Square Section 150mm Half Round 115mm High Capacity Ogee 0.54 1.67 2.17 3.67 3.97 4.58 0.75 2.34 3.04 5.13 5.56 4.84 32 80 104 176 190 217 46 112 144 246 266 236

These values can be used except in the following circumstances: If sharp cornered 90 angle fixed within:a) 2 metres of outlet then increase roof area which can be drained by 20%. b) 2 to 4 metres of outlet then increase roof area which can be drained by 10%. If round cornered 90 angle fixed within:a) 2 metres of outlet then increase roof area which can be drained by 10%. b) 2 to 4 metres of outlet then increase roof area which can be drained by 5%.

C B

h Lengt

For further information refer to BS 6367: 1983 Drainage of Roofs and Paved areas. In the case of flat roofs, the roof plan area should be used. 16

Product Data - Design - Sitework continued

Jointing Clickfit Half Round and Square Rainwater

q Check gutter is correct length. q End must be in line with marks in fitting. q To take joint apart, apply pressure as shown to lever nib and gutter.

q Insert back of gutter fully under clip lip at back of fitting. q Pull gutter down slide until it clicks into position under front lever nib.

q Completed joint provides a slim streamlined profile which is strong and leakproof.

Fixing

q Use 1 inch No. 8 rust protected roundhead wood screws to fix brackets and outlets to fascia board. q Rise and fall brackets are used where there is no fascia board and as an alternative to rafter brackets.

q Rafter brackets are used where there is no fascia board and as an alternative to rise and fall brackets. q Top rafter brackets must be fixed before roof is tiled whereas side rafter brackets may be fixed after roof has been tiled.

q Downpipe should be supported by use of appropriate fixing bracket. q Square downpipe can be fixed completely flush with wall or standing off for future maintenance. Round downpipe stands clear of wall.

Expansion

Cutting

q All gutter fittings are pre-marked with gutter fixing marks to allow for recommended expansion. q Join subsequent downpipe lengths using pipe connectors leaving an expansion gap of 10mm at each joint. q Always connect downpipe to running outlet or offset spigot leaving 10mm gap for expansion.

q When gutter needs to be cut, use a fine-toothed hand saw and ensure that cut is clean and square and thoroughly deburred before gutter is fixed.

17

SOIL

Description The Vinyl Floor Gully is available in nominal 50mm and 82mm outlets with a three part heavy duty grid and clamp to accommodate vinyl ooring. The gully body (S409) will connect to 50mm waste pipe to BS 5254 and BS 5255. The gully body (S411) will connect to 82mm PVC-U soil and drainage pipe to BS 4514 or BS 4660. Material The Vinyl Floor Gully grid and clamp is manufactured from High impact PVC-U. The gully body is manufactured from PVC-U. All seals are EPDM. The clamp xing screws are stainless steel. Benets q Unique design allows for complete versatility and compatibility for all drainage situations. q Self locating six point clamp means a quick and easy installation. q Self locating twist & lock grid can be removed for cleaning and rodding. q Gully body allows for up to three waste pipe connections of sizes 32mm, 40mm or 50mm using boss adaptors S420, S421 or S422. q Gully grid has a textured surface and is particularly suitable for wheelchairs and heavily trafcked areas. q Material compatibility with vinyl ooring and vinyl oor adhesive provides an integrated solution to surface area drainage. Specication - Showing 50mm Outlet

Solid Concrete Floor (Fig. No. 1).

Alternative Gully Applications (1) Suspended Floor using the funnel bowl (Fig. No. 2)

Gully Extension Piece 110mm Pipe Funnel Bowl O-Ring Seals

(2) Suspended Floor extending the funnel (Fig. No. 3)

Self Locating Clamp
Gully Extension Piece

(3) Solid Ground Floor (Fig. No. 4)

Twist Lock Grid

110mm Pipe

40mm Pipe 82mm Pipe

Funnel Clamp Base O-Ring Seal

40mm Pipe

Trap Extension Bowl O-Ring Seals

Floor Gully Body

(4) Ground Floor Connection Direct to Drain (Fig. No. 5) Fixing The method of xing is dependant on the type of oor construction. In solid concrete oors, the gully can be installed within the oor itself (Fig. No. 1). In timber or concreted suspended oors, the gully body may require additional support by strapping or boxing in. In solid oors, the clamp base can be solvent welded directly to the gully body. In suspended oors an intermediate length of 110mm soil or PlastiDrain pipe will position the outlet clear of joists or beams (Fig. No. 2). When the gully is in position in the oor, the vinyl oor covering can be laid over the gully. Care should be taken to record the position of the gully prior to the vinyl oor covering being laid. The vinyl oor covering is cut and trimmed to the line indicated on the clamp base. The ooring is glued into the clamp base, taking care that there is no glue below the line. The self locating clamp is positioned in the clamp base, and xed with the self tapping screws supplied. Care should be taken to ensure that the screws at opposite sides of the clamp are tightened together so that unequal pressure is not placed upon the clamp base. Care should also be taken not to over tighten the screws. When the vinyl ooring is xed tightly in the clamp, the self locating grid can be tted using the twist lock action. To clean or rod the gully, remove the gully grid and take out the funnel and O-ring. When replacing the funnel, ensure that the O-ring is tted correctly.
SuperSleve Low Back P-Trap O-Ring Seal Gully Extension Piece SuperSleve Pipe 110mm Plastics Pipe

(5) Ground Floor Connection to Drain Using Low Back P Trap 100mm PlastiDrain (Fig. No. 6)

110mm Plastics Pipe

SuperSleve to 110mm Plastics Adaptor

Gully Extension Piece

Funnel Bowl

PlastiDrain Low back P Trap

(6) 100mm SuperSleve (Fig. No. 7)

HepSleve to SuperSleve Adaptor SuperSleve Pipe SuperSleve Coupling

18

Hygienic Self Sealing Waste Valve

Prevents the escape of foul sewer air from waste discharge systems. Actively maintaining a pressure equilibrium in soil and waste installations. is a self sealing valve designed to close the waste connection below a sanitary appliance to prevent the escape of foul sewer air into the dwelling and thereby complies with the requirements of BS 5572: 1994 Code of practice for Sanitary pipework and Document H of the Building Regulations 1985 Drainage and Waste Disposal. Where there is a waste branch which enters the stack above the WC branch, will provide an air inlet and no air admittance valve is required. Note: Care should be taken to ensure that the underground drainage system is not completely sealed. Natural open ventilation is required at the head of each main drain run and/or at every tenth dwelling. Extensive testing has shown that the valve performs under everyday conditions in which traditional water sealed traps are prone to failure. The valve will perform under back pressures which are 10 times greater than those experienced in a typical soil and waste system.

functions without the use of water, and complies with all other relevant functional requirements of BS 3943: Specication for plastics waste traps. is certied by WIMLAS; certicate number 042/97, to be a satisfactory means of excluding foul air from a building within a single stack drainage system. BBA Certication is applied for.

The

Range - Product Selector

valve can be installed vertically or horizontally (with an adaptor) and is available in 32mm and 40mm. Material: Polypropylene Colour: White Certication: WIMLAS Certicate Number 042/97 - Revision 1, June 1998.

Universal Compression Outlet

Nominal Diameter mm Waste Valve
Hygenic Self Sealing Waste Valve

32

40

Nominal Diameter mm 871/2

32

40

Nominal Diameter mm Running Adaptor

32

40

Knuckle Adaptor

Use with valve for horizontal applications

Use with waste valve when installing in a pipe run

- Sitework
Inlet The inlet is provided with a screwed cap, anged tail and sealing ring, which are designed to connect to waste ttings conforming to BS EN 274, or BS 3380, or to a Fixing When xed horizontally to an appliance outlet or to a sloping pipe, in order to prevent standing water and to provide a continuous fall, installed with the ribs underneath - Fig. No. 1. must be inlet adaptor. Offer up the inlet to the threaded tail of the waste pipe and tighten the threaded cap by hand (check that the cap screws on square and does not cross-thread), hand tight should be adequate. When the screwed cap is tight, proper seating should be obtained, and the Outlet The outlet is provided with a universal compression connection which is designed for use with BS 5254 Polypropylene pipe, BS 5255 ABS, MUPVC or polypropylene pipe, BS 2871: Part 1: Table X copper pipe, or equivalent imperial size copper pipe to BS 659. body should be secure.

Fig. No. 1

Orientation when installed horizontally

RIGHT
Flow


WRONG
Side Elevation

When installed horizontally the ribs must be at the bottom to ensure correct operation.

19

- Sitework - continued
Fixing 1 Cut the pipe to length, allowing for the full compression socket depth, (preferably using an appropriate pipe cutter). 2 Remove any swarf from the end of the plastic pipe. Ream the copper pipe end to remove any burr, and le if necessary to remove any external sharp edges. Mark the socket depth on the pipe, and check that the pipe section to be jointed is free of any surface damage which may affect the joint seal. Unscrew the cap from the seal onto the pipe. Fig. No. 2. outlet, and slide the cap and rubber
Counter Top Basin Pedestal Basin 1 No. 32mm 1 No. 32mm 1 No. 40mm 1 No. 40mm Knuckle Adaptor 1 No. 40mm 1 No. 40mm Spigot Bend Knuckle Adaptor 1 No. 32mm 1 No. 32mm 1 No. 32mm Knuckle Bend 1 No. 32mm 1 No. 32mm running Adaptor 1 No. 32mm Cap & Lining 2 No. 32mm Bends

within pedestal

3 4 5

Insert the pipe end fully into the socket. Slide the rubber seal and screwed cap up against the face of the socket, and tighten the cap by hand, (check that the cap is square to the body and does not cross-thread), hand tight should be adequate to form a proper seal. N.B DO NOT USE ANY JOINTING COMPOUND OR SEALANT ON THE CONNECTIONS. INLET OR OUTLET

Bath or Shower

Urinal

Fig. No. 2

Outlet Connection
1 No. 40mm 1 No. 40mm 2 No. 40mm Bends Knuckle Adaptor

Capnut and sealing cone on pipe end ready for insertion of pipe into compression socket.

Knuckle Adaptor used to angle back to wall

Fig. No. 3 Dimensional Data Principal Dimensions Size 32mm 40mm C 8 5 E 171 171 L 208 208 W 211 213 Z 40 40
Sink Washing Machine

Application can be used on any waste appliance, the installation arrangement will depend on the dimensional design of the appliance and site constraints. Fig. No. 4 shows some of the mounting options for . can be xed directly to the waste outlet of an appliance, or by using the appropriate adaptor, mounted in the horizontal position either at the appliance or on the pipe. may be installed at any angle between vertical and horizontal. Fig. No. 4 Mounting Options

End of appliance screwed outlet

End of appliance screwed outlet Flow Z C W

L

Flow

C a) Fixed vertically directly to appliance outlet b) Fixed on a pipe at any sloping angle using inlet adaptor Cat. No. BV3 or CV3 (available separately) c) Fixed horizontally to appliance outlet using inlet bend adaptor Cat. No. BV11 or CV11 (available separately)

20

;;
Notes

;; ; ; ; ; ; ;

Ducted Basin

Bidet

1 No. 40mm 1 No. 32mm running Adaptor 1 No. 40mm Bend

1 Dimensions are nominal and may vary slightly due to compression of the rubber seals. 2 When xed to a pipe, it is recommended that should remain accessible.

w Flo

- Sitework - continued
Waste pipes should have sufcient slope to convey the likely ow, but should not be less than 18mm/metre in accordance with BS 5572. When using , there is no maximum slope limitation which is often a restriction applicable to single stack waste systems. As is unaffected by siphonage or compression, combined waste piping can be used to connect more than one appliance to the stack. Fig. No. 5 shows how can be used to simplify the plumbing to the typical bathroom. Any branch discharge pipes serving appliances not tted with (eg. a range of W.Cs) should be designed and installed in accordance with BS 5572. Discharge stacks should continue to be sized, and vented where appropriate, in accordance with BS 5572.

;;;;; ;;;;; ;; ; ;;;;; ;; ;; ;; ;; ;;;;

Fig. No. 5 Installation in a Typical Bathroom
32mm within pedestal, at base of drop pipe bends back to tee on branch Short Boss Pipe and Boss Adaptor 40mm Spigot Bend and other Bends as required 40mm Tee and 40mm x 32mm Socket Reducer 40mm (with Knuckle Adaptor) mounted horizontally to route pipe back to wall

HepFlex Soil
HepFlex Soil - Flexible Pan Connector (Long)
Description Nom. Dia. 110mm Nom. Length 310mm Cat. No. S170 Nom. Extended Length 925mm q The multiple finned pipe spigot seal ensures a reliable flexible sealing area in a wide variety of pipes. q Facilitates conversion of a low-level bathroom suite to a close-coupled pan where the drain connection is fitted closer to the wall. q Lightweight, easy to handle, remaining compact until installation. q Provides a larger offset within a shorter distance thereby eliminating the number of fittings required and reducing installation time and cost. When fully extended the Flexible Pan Connectors should be suitably supported to avoid the possibility of sagging. Flexible Pan Connectors require push-fit installation, wetting of the seals with water is recommended. Any resistance can be eased by use of a watersoluble lubricant. Greases should not be used.

Flexible Pan Connector - Long

HepFlex Soil - Flexible Pan Connector (Short)

Description Nom. Dia. 110mm Nom. Length 250mm Cat. No. S171 Nom. Extended Length 675mm

Flexible Pan Connector Short

Installation Connection to 110mm (4in) single branch - 871/2 soil pipe which is offset

Application To offset pipe

Connector S171 or S170

The HepFlex Soil Flexible Pan Connectors provide the perfect solution when connecting horizontal pan outlets to rigid soil systems. Where the length of the W.C. connection is non-standard, the HepFlex Soil Flexible Pan Connectors can be extended to provide the required length. Description Flexible Pan Connectors are designed for horizontal outlet W.C. pans to BS 5503 and will fit 110mm PVC-U soil pipe to BS 4514/BS EN 1329-1, 110mm PVC-U underground drainage pipe to BS 4660/BS EN 1401-1, 100mm clay underground drainage pipe to BS EN 295, BS 65 and 102mm cast iron to BS 416. Flexible Pan Connectors are manufactured in white polypropylene with EPDM seals. Pending WIMLAS Certificate. Installation Benefits q The flexible nature of these products provides an inexpensive on-site solution to awkward connections in confined spaces. q Flexible stay-put pipe retains its profile once installed. q Push-fit joint, therefore no mastics or jointing compounds are required.

Connection to 110mm (4in) single branch - 871/2 soil pipe which is very close to the pan itself Connection to 110mm (4in) soil pipe via a 90 bend which can be horizontal or vertical

Question mark profile

S170

To 90 pipework

S171 or S170

Connection to 110mm (4in) soil pipe via a double 90 bend which can be horizontal or vertical

Double 90 bend

S170

21

HepFlex Waste
The HepFlex Waste range provides the professional installer with an efcient means to connect to appliances and existing waste in difcult situations. It is designed to complement rigid waste systems by providing an alternative method of connecting the appliance valve or trap to rigid waste. It can also be used to facilitate the connection of two xed points within a waste system. The concise range allows connection to push t and solvent weld systems with either factory assembled xed lengths or made to measure lengths cut from coils and assembled on site. The HepFlex Waste range has been designed to use in conjunction with the hygienic self sealing valve from Hepworth Plumbing as well as conventional water seal traps.

HepFlex Waste - Product Selector

Certication: WIMLAS Certicate Number 065/99 September 1999
Description Nom Dia Type Cat No Pack Description Nom Dia Type Cat No Pack Description Nom Dia Type Cat No Pack

Material: PVC Colour: White Smooth Bore Flexible Waste Pipe 3 metre coil

mm

Material: ABS Colour: White Fabricated Lengths Effective 315mm Length Effective 365mm Length

mm 32 32 40 40 PF SW PF SW FBW30 FSBW30 FCW30 FSCW30 1 1 1 1

Material: ABS Colour: White Spigot Connector

mm 32 32 40 40 32 40 PF FBW6 10 SW FSBW6 10 PF FCW6 10 SW FSCW6 10 BW17 50 CW17 50

32 40

N/A N/A

FBP3 FCP3

1 1

} }

Accessories Pipe Clip

6 metre coil

32 40

N/A N/A

FBP6 FCP6

1 1

Pipe Cutter up to 42mm Solvent Cement 250mm can 75g tube

HD77

S241 S242

1 1

HepFlex Waste - Sitework

Jointing
Connection of HepFlex Waste ttings and HepFlex exible waste pipe 1 Check you have the correct HepFlex Waste ttings for the type of waste system you are connecting to FBW6 or FCW6 for push t waste to BS 5254 and FSBW6 or FSCW6 for solvent weld waste to BS 5255. 2 Cut the HepFlex Waste pipe square using the recommended cutters (HD77). 3 Ensure the inner surface of the HepFlex Waste pipe and the tapered spigot of the HepFlex Waste ttings are clean and dry. 4 Apply solvent cement (S242) evenly over mating surfaces of both pipe and tapered spigot. Insert the tapered spigot into the pipe with a slight twisting action to the full spigot depth. 5 Surplus cement should be removed with a cloth. The joint should be rm enough to handle within 5 minutes. Please observe the safety precautions detailed on each can of solvent cement. Note: There is a small gap between the I.D. of the pipe and the O.D. of the tapered spigot. This is to allow sufcient solvent cement into the joint to make a good weld. Push Fit Systems to BS 5254 Perform steps 1 to 5 as detailed overleaf using either FBW6 for 32mm waste or FCW6 for 40mm waste. If a prefabricated HepFlex Waste unit is being used then ensure you have the correct unit for the type of waste system you are connecting to (FBW30 or FCW30 for push t waste) and proceed with step 6.

6 Lubricate the HepFlex parallel (not tapered) spigot and the socket of the push t waste tting with Silicon Lubricant (S254) and push t to the full socket depth. Withdraw the pipe 5mm on the waste system to allow for expansion. Solvent Weld Systems to BS 5255 Perform steps 1 to 5 as detailed overleaf using either FSBW6 for 32mm waste or FSCW6 for 40mm waste. If a prefabricated HepFlex Waste unit is being used then ensure you have the correct unit for the type of waste system you are connecting to (FSBW30 or FSCW30 for solvent weld waste) and proceed with step 7. 7 Use cleaning uid (S243) on the HepFlex parallel (not tapered) spigot and the inner surface of the solvent weld tting. 8 Apply solvent cement (S242) evenly over mating surfaces of both the spigot and socket and insert the spigot into the socket with a twisting action to the full socket depth. 9 Surplus cement should be removed with a cloth. The joint should be rm enough to handle within 5 minutes. Please observe the safety precautions detailed on each can of solvent cement. Connection to or Water Seal Traps hygienic self sealing waste valves and most water seal traps will accept both push t waste to BS 5254 and solvent weld waste to BS 5255 and so will accept HepFlex Waste ttings. Bend Lengths It is recommended that HepFlex Waste pipe is not bent tighter than four times diameter.

22

HepFlex Waste - Sitework - continued

Factory made lengths in 32mm are 315mm long which is sufcient for a 90 bend or a 75mm offset. The 40mm assembled lengths are 365mm long which is also sufcient for a 90 bend and a 100mm offset. All lengths of HepFlex Waste should be clipped or suitably supported to ensure compliance with the Building Regulations. Pipe clips BW17 (32mm) or CW17 (40mm) can be used. Lengths fitted horizontally should be fully supported. Horizontal lengths greater than 200mm should be supported every 150mm for a minimum distance of 15mm. When connecting HepFlex Waste to short lengths of rigid pipe, the rigid pipe needs to be supported using a minimum of 2 clips. The location of the clips should be not more than 100mm from the ends of the rigid pipe to accommodate ttings and positional adjustment. For longer runs, the rigid pipe should be clipped in the conventional manner as follows: Horizontal installation 0.75m centres Vertical installation 1.5m centres
W

To avoid the possibility of sagging, the width (W) should never exceed height (H).
H

Soil Manifold
The Hepworth Soil Manifold is designed to t neatly into the corner of the bathroom and will allow for a quicker and easier connection of all soil and waste pipes above oor level. The three Manifold inlets are push t requiring no extra boss adaptors or solvent weld jointing to make connections. The inlets hold a universal single seal which will accept 32 and 40mm waste pipes to BS 5254, BS 5255 and Imperial and metric copper sizes. 50mm inlets are also supplied in addition to a combination of inlet sizes.
3 2 1 All inlets = 32/40mm Inlet 1 = 50mm 2 & 3 = 32/40mm Inlet 3 = 50mm 1 & 2 = 32/40mm Other inlet combinations are available to special order. S300/A S300/B S300/C

Air Admittance Valve

Hepworth Plumbing Air Admittance valves are recommended for use in above ground drainage systems installed in domestic and non-domestic buildings in accordance with BS 5572: 1994. 1. The valves provide a means of ventilation to the drainage system to prevent the loss of water seals in traps and consequent release of foul air into the building. 2. The valves are for internal use only, and should preferably be installed in a non-habitable space, such as a duct or roof where it is easily accessible but not subject to interference. The insulating polystyrene cover should be left in place when there is a possibility of condensation forming within the valve. 3. The S204 valves are for use on soil stacks serving buildings up to ve storeys high. The S204 can be connected directly to 110mm pipe by pushing the pipe over the rubber seal. For connection to 82mm pipe the pipe should be pushed into the rubber seal. 4. The S204/2 valves are for use on soil stacks serving buildings up to three storeys high. The S204/2 is also suitable for connection to waste pipes to prevent water loss from the trap seals by self and induced syphonage arising from water ow in small diameter branch discharge pipes. The S204/2 can be connected directly to 110mm pipe by pushing the pipe over the rubber seal. For connection to 82mm pipe, the pipe should be pushed into the rubber seal. For connection to 50mm pipe, the 110/82mm adaptor should be discarded, and the valve connected directly to the pipe using the 50mm compression outlet.

Benets q Easy installation of pipes above oor level. q Simple Push-Fit connections for all waste pipes. q No additional bosses or solvent jointing. q Waste connectors can be horizontal using swivel elbows or vertical as required. q Complete with universal seals, blanking plugs, integral pipe stops and manifold template. q Any combination of 32mm, 40mm and 50mm inlets supplied. q Self cleansing with wash down action. q Protection from induced syphonage on connecting runs. q No need for oor channels or pipe runs in cavity oors. q Allows design freedom to eliminate unsightly runs of waste pipe on external walls. q Can be used as a gully when tted at foot of external stack. q Complies with current Codes of Practice. q Carries agrment certicate no. 86/1733.

Application Guidance 1. The head of any drain should be vented to atmosphere. 2. Any branch longer than 6m to a single appliance, or 12m to a group of appliances. 3. No more than nine consecutive branch drains should be vented with air admittance valves. 4. Valves should be installed within the building, preferably in a non-habitable space where there is limited risk of freezing. 5. Valves should be tted above the overspill level of the highest appliance. 23

PLUMBING HOTLINES
ABOVE GROUND PLASTICS AND Hep2O ORDERS & ENQUIRIES TECHNICAL SUPPORT LITERATURE SERVICE Tel: 01709 856400 Tel: 01709 856406 Tel: 01709 856408 Fax: 01709 856401 Fax: 01709 856407 Fax: 01709 856409

PRESSURE PIPE AND DUCT ORDERS & ENQUIRIES OFFICE HOURS For all orders and enquiries: 8.30am-5.00pm. Answerphones operate outside these times. Tel: 01709 856402 Fax: 01709 856403

Edlington Lane Edlington Doncaster DN12 1BY UK Tel: +44 (0)1709 856300 Fax: +44 (0)1709 856301
www.hepworthplumbing.co.uk e-mail: info@hepworthplumbing.co.uk Copyright Hepworth Building Products Limited Hep2O, HepvO, HepFlex are registered trademarks of Hepworth Building Products. Our policy is one of constant development. Whilst this publication is accurate at the date of printing, specification/approvals may be changed in the interest of continued improvement.
AGPG/1/?M/01/01 - 1122