Seminar On " ": Pre Engineered Buildings

SEMINAR ON
PRE ENGINEERED BUILDINGS
Concept , Design
&
Construction
By
Prasad Bishetti
INTRODUCTION
Pre-determined inventory of raw materials that can satisfy a
wide range of structural and aesthetic design requirements.
Pre-Engineered Buildings can be adapted to suit a wide

variety of structural applications, the greatest economy will
be realized when utilizing standard details. An efficiently
designed Pre-Engineered Building can be lighter that the
conventional steel buildings by up to 30%.
These are the structures basically produced at the factory
with high tensile steel material by collecting complete
information of the shed/building (viz; Length, Width,
Height etc,).
The entire design of column, rafters and other accessories
is based on International structural standards and involve
high technical welding and quality production.
BUILDING COMPONENTS
1. Prime Steel Framing Systems
2. Secondary Systems
Secondary structural steel framing system refers to purlins,
girts, eave struts, wind bracing, flange bracing, base angles,
clips and other miscellaneous structural parts.
3. Coated Steel Sheet Products
Colour coated sheets provide excellent resistance to

corrosion and hence has become the most preferred material
for a wide range of construction uses, particularly roofing
and walling.
4. Decking Sheets
Flordec Sheets (Corrugated Sheet for Composite Floor)
Flordec decking sheets are composite floor systems,

constructed with cold-rolled corrugated steel decking
covered with concrete.
Insulation (PEBI)
Uniformly textured inorganic glass fibers bonded together
by a non-water soluble and fire-retardant thermosetting
resin. It is free from coarse fibers and shot due to its
mineral composition.
PEBI is non-toxic and not hazardous to health.
DESIGN OF PRE ENGINEERED
BUILDINGS
The main framing of PEB systems is analyzed by the
stiffness matrix method.
The frame data is assembled based on number of frame
members, number of joints, number of degrees of freedom,
the conditions of restraint and the elastic properties of the
members.
The overall joint stiffness matrix is obtained based on the
above frame data by summation of individual stiffness
matrices considering all possible displacements.
The load vector is then generated based on the loading data
and the unknown displacements are obtained by inverting
the overall joint stiffness matrix and multiplying with the
load vector.
Design Codes
AISC: American institute of steel construction manual
AISI: American iron and steel institute specifications
MBMA: Metal building manufacturers code
ANSI: American national standards institute specifications
ASCE: American society of civil engineers
UBC: Uniform building code
IS: Indian standards

Latest International Codes & Deflection
Design Criteria
DESIGN METHOD: Allowable stress design method is
used as per the AISC specifications.
DEFLECTIONS: Unless otherwise specified, the

deflections will go to MBMA, AISC criteria and standard
industry practices.
PRIMARY FRAMING: Moment resisting frames with

pinned or fixed bases.
SECONDARY FRAMING: Cold formed Z sections or C
sections for purlins or girts designed as continuous beams
spanning over rafters and columns with laps.
LONGITUDANAL STABILITY: Wind load on building

end walls is transferred through roof purlins to braced bays
and carried to the foundations through diagonal bracing.
DESIGN SOFTWARE
The latest software that is used for design is STAAD 2007.

ERECTION SYSTEM
Preparation for Erection

1. Pre Erection checks
2. Receiving Materials at site
3. Unloading Containers
Erection of the Framing

1. Preparation of the First Bay
2. Main frames
3. Mezzanine floors
4. Crane Beams
Sheeting & Trimming
Sheeting preparation
Sheeting the walls
Sheeting the roofs
Miscellaneous trimmings
Fascia
Self weight Self weight
30% lighter More heavy
Primary Member is Primary members are
tapered section Hot rolled I section
Secondary members Secondary members are
are light weight rolled I or C section
framed Z and C which are heavy in
section weight.
Delivery average 6 to 8 Delivery- average 20 to
weeks 26 weeks
Foundation-simple design, Foundation- expensive,
easy to construct & light heavy foundation
wt. required.
Erection cost and time- Erection cost and time-
accurately known 20% more than PEB
Overall price - Higher
Overall price -30%lower
price per square meter.
Architecture-achieved at
Architecture- achieved at
low cost
higher cost
Erection process is easy,
Erection process is slow
fast, step by step
and extensive field labor
is required.
PRE ENGINEERED BUILDING vs
CONCRETE BUILDINGS
APPLICATIONS
Industrial Buildings
Warehouses
Commercial Complexes
Showrooms
Offices
Schools
Indoor Stadiums
Outdoor Stadiums with canopies
Gas Stations
Metro Stations, Bus Terminals, Parking Lots
Primary Health Centers, Angan wadis
And many more
Industrial Indoor Stadiums
Building
Parking lots Railway Station

Aircraft Hangars Metro Station
Wear house High rise Building

ADVANTAGES
Aesthetic Appeal
Faster Completion
Economical
Seismic Resistance
Ease of Expansion
Maintenance Free
Large Clear Spans
Controlled Quality
CONCLUSION
PEB concept has been very successful and well established

in North America, Australia and is presently expanding in
U.K and European countries. PEB construction is 30 to
40% faster than masonary construction. PEB buildings
provide good insulation effect and would be highly suitable
for a tropical country like India.
The pre-engineered building calls for very fast construction

of buildings and with good aesthetic looks and quality
construction. Pre-engineered Buildings can be used
extensively for construction of industrial and residential
buildings.
REFERENCES
KIRBY Building System KUWAIT.

KARTHIK FABRICATORS India P Ltd.
MULTCOLOR PROJECTS India Ltd.
LLOYD INSULATIONS India Ltd
MABANI STEEL LLC, U.A.E
STRUCTURAL ENGINEERING at WSP Asia Limited
Philippines
ZAMIL STEEL Building India Pvt.Ltd

Seminar On " ": Pre Engineered Buildings

Uploaded by

Copyright:

Available Formats

Seminar On " ": Pre Engineered Buildings

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Seminar On " ": Pre Engineered Buildings

Uploaded by

Copyright:

Available Formats

What are the main components of pre-engineered buildings?

What are the main components of pre-engineered buildings?

How are pre-engineered buildings designed and analyzed?

How are pre-engineered buildings designed and analyzed?

SEMINAR ON

PRE ENGINEERED BUILDINGS

Pre-Engineered Buildings can be adapted to suit a wide

Colour coated sheets provide excellent resistance to

Flordec decking sheets are composite floor systems,

AISC: American institute of steel construction manual

AISI: American iron and steel institute specifications

MBMA: Metal building manufacturers code

ANSI: American national standards institute specifications

ASCE: American society of civil engineers

UBC: Uniform building code

IS: Indian standards

DEFLECTIONS: Unless otherwise specified, the

PRIMARY FRAMING: Moment resisting frames with

LONGITUDANAL STABILITY: Wind load on building

The latest software that is used for design is STAAD 2007.

Preparation for Erection

Erection of the Framing

Sheeting the walls

Sheeting the roofs

Parking lots Railway Station

Wear house High rise Building

PEB concept has been very successful and well established

The pre-engineered building calls for very fast construction

KIRBY Building System KUWAIT.

You might also like