Chapter 21

Alternating Current Circuits

and Electromagnetic Waves
AC Circuit
 An AC circuit consists of a combination of
circuit elements and an AC generator or
source
 The output of an AC generator is sinusoidal
and varies with time according to the
following equation
 Δv = ΔVmax sin 2ƒt
 Δv is the instantaneous voltage
 ΔVmax is the maximum voltage of the generator
 ƒ is the frequency at which the voltage changes, in Hz
Resistor in an AC Circuit
 Consider a circuit
consisting of an AC source
and a resistor
 The graph shows the
current through and the
voltage across the resistor
 The current and the
voltage reach their
maximum values at the
same time
 The current and the
voltage are said to be in
phase
More About Resistors in an AC
Circuit
 The direction of the current has no effect on
the behavior of the resistor
 The rate at which electrical energy is
dissipated in the circuit is given by
 P = i2 R
 where i is the instantaneous current
 the heating effect produced by an AC current with a
maximum value of Imax is not the same as that of a DC
current of the same value
 The maximum current occurs for a small amount of time
rms Current and Voltage
 The rms current is the direct current
that would dissipate the same amount
of energy in a resistor as is actually
dissipated by the AC current
Imax
Irms   0.707 Imax
2
 Alternating voltages can also be
discussed in terms of rms values
Vmax
Vrms   0.707 Vmax
2
Ohm’s Law in an AC Circuit
 rms values will be used when discussing
AC currents and voltages
 AC ammeters and voltmeters are designed
to read rms values
 Many of the equations will be in the same
form as in DC circuits
 Ohm’s Law for a resistor, R, in an AC
circuit
 ΔVrms = Irms R
 Also applies to the maximum values of v and i
Capacitors in an AC Circuit
 Consider a circuit containing a capacitor and
an AC source
 The current starts out at a large value and
charges the plates of the capacitor
 There is initially no resistance to hinder the flow of
the current while the plates are not charged
 As the charge on the plates increases, the
voltage across the plates increases and the
current flowing in the circuit decreases
More About Capacitors in an
AC Circuit
 The current reverses
direction
 The voltage across
the plates decreases
as the plates lose
the charge they had
accumulated
 The voltage across
the capacitor lags
behind the current
by 90°
Capacitive Reactance and
Ohm’s Law
 The impeding effect of a capacitor on the
current in an AC circuit is called the capacitive
reactance and is given by
1
XC 
2 ƒC
 When ƒ is in Hz and C is in F, XC will be in ohms
 Ohm’s Law for a capacitor in an AC circuit
 ΔVrms = Irms XC
Inductors in an AC Circuit
 Consider an AC circuit
with a source and an
inductor
 The current in the
circuit is impeded by
the back emf of the
inductor
 The voltage across the
inductor always leads
the current by 90°
Inductive Reactance and
Ohm’s Law
 The effective resistance of a coil in an
AC circuit is called its inductive
reactance and is given by
 XL = 2ƒL
 When ƒ is in Hz and L is in H, XL will be in
ohms
 Ohm’s Law for the inductor
 ΔVrms = Irms XL
The RLC Series Circuit
 The resistor,
inductor, and
capacitor can be
combined in a circuit
 The current in the
circuit is the same at
any time and varies
sinusoidally with
time
Current and Voltage
Relationships in an RLC Circuit
 The instantaneous
voltage across the
resistor is in phase with
the current
 The instantaneous
voltage across the
inductor leads the
current by 90°
 The instantaneous
voltage across the
capacitor lags the
current by 90°
Phasor Diagrams
 To account for the
different phases of the
voltage drops, vector
techniques are used
 Represent the voltage
across each element as
a rotating vector, called
a phasor
 The diagram is called a
phasor diagram
Phasor Diagram for RLC
Series Circuit
 The voltage across the
resistor is on the +x
axis since it is in phase
with the current
 The voltage across the
inductor is on the +y
since it leads the
current by 90°
 The voltage across the
capacitor is on the –y
axis since it lags behind
the current by 90°
Phasor Diagram, cont
 The phasors are
added as vectors to
account for the
phase differences in
the voltages
 ΔVL and ΔVC are on
the same line and so
the net y component
is ΔVL - ΔVC
ΔVmax From the Phasor
Diagram
 The voltages are not in phase, so they cannot
simply be added to get the voltage across the
combination of the elements or the voltage
source
Vmax  VR  ( VL  VC )2
2

VL  VC
tan  
VR
  is the phase angle between the current and
the maximum voltage
Impedance of a Circuit
 The impedance, Z,
can also be
represented in a
phasor diagram

Z  R 2  ( XL  X C ) 2
XL  X C
tan  
R
Impedance and Ohm’s Law
 Ohm’s Law can be applied to the
impedance
 ΔVmax = Imax Z
Summary of Circuit Elements,
Impedance and Phase Angles
Problem Solving for AC
Circuits
 Calculate as many unknown quantities
as possible
 For example, find XL and XC
 Be careful of units -- use F, H, Ω

 Apply Ohm’s Law to the portion of the

circuit that is of interest
 Determine all the unknowns asked for
in the problem
Power in an AC Circuit
 No power losses are associated with
capacitors and pure inductors in an AC circuit
 In a capacitor, during one-half of a cycle energy is
stored and during the other half the energy is
returned to the circuit
 In an inductor, the source does work against the
back emf of the inductor and energy is stored in
the inductor, but when the current begins to
decrease in the circuit, the energy is returned to
the circuit
Power in an AC Circuit, cont
 The average power delivered by the
generator is converted to internal
energy in the resistor
 Pav = IrmsΔVR = IrmsΔVrms cos 
 cos  is called the power factor of the
circuit
 Phase shifts can be used to maximize
power outputs
Resonance in an AC Circuit
 Resonance occurs at
the frequency, ƒo,
where the current has
its maximum value
 To achieve maximum
current, the impedance
must have a minimum
value
 This occurs when XL = XC
1
ƒo 
2 LC
Resonance, cont
 Theoretically, if R = 0 the current would be
infinite at resonance
 Real circuits always have some resistance
 Tuning a radio
 A varying capacitor changes the resonance frequency
of the tuning circuit in your radio to match the station
to be received
 Metal Detector
 The portal is an inductor, and the frequency is set to a
condition with no metal present
 When metal is present, it changes the effective
inductance, which changes the current which is
detected and an alarm sounds
Transformers
 An AC transformer
consists of two coils
of wire wound
around a core of
soft iron
 The side connected
to the input AC
voltage source is
called the primary
and has N1 turns
Transformers, 2
 The other side, called the secondary, is
connected to a resistor and has N2 turns
 The core is used to increase the
magnetic flux and to provide a medium
for the flux to pass from one coil to the
other
 The rate of change of the flux is the
same for both coils
Transformers, 3
 The voltages are related by
N2
V2  V1
N1
 When N2 > N1, the transformer is
referred to as a step up transformer
 When N2 < N1, the transformer is
referred to as a step down transformer
Transformer, final
 The power input into the primary equals
the power output at the secondary
 I1ΔV1 = I2ΔV2
 You don’t get something for nothing
 This assumes an ideal transformer
 In real transformers, power efficiencies typically
range from 90% to 99%
Electrical Power Transmission
 When transmitting electric power over long
distances, it is most economical to use high
voltage and low current
 Minimizes I2R power losses
 In practice, voltage is stepped up to about
230 000 V at the generating station and
stepped down to 20 000 V at the distribution
station and finally to 120 V at the customer’s
utility pole
James Clerk Maxwell
 Electricity and
magnetism were
originally thought to be
unrelated
 in 1865, James Clerk
Maxwell provided a
mathematical theory
that showed a close
relationship between all
electric and magnetic
phenomena
Maxwell’s Starting Points
 Electric field lines originate on positive
charges and terminate on negative charges
 Magnetic field lines always form closed loops
– they do not begin or end anywhere
 A varying magnetic field induces an emf and
hence an electric field (Faraday’s Law)
 Magnetic fields are generated by moving
charges or currents (Ampère’s Law)
Maxwell’s Predictions
 Maxwell used these starting points and a
corresponding mathematical framework to prove
that electric and magnetic fields play symmetric
roles in nature
 He hypothesized that a changing electric field
would produce a magnetic field
 Maxwell calculated the speed of light to be 3x108
m/s
 He concluded that visible light and all other
electromagnetic waves consist of fluctuating
electric and magnetic fields, with each varying
field inducing the other
Hertz’s Confirmation of
Maxwell’s Predictions
 Heinrich Hertz was
the first to generate
and detect
electromagnetic
waves in a
laboratory setting
Hertz’s Basic LC Circuit
 When the switch is
closed, oscillations
occur in the current and
in the charge on the
capacitor
 When the capacitor is
fully charged, the total
energy of the circuit is
stored in the electric
field of the capacitor
 At this time, the current
is zero and no energy is
stored in the inductor
LC Circuit, cont
 As the capacitor discharges, the energy stored in
the electric field decreases
 At the same time, the current increases and the
energy stored in the magnetic field increases
 When the capacitor is fully discharged, there is
no energy stored in its electric field
 The current is at a maximum and all the energy is
stored in the magnetic field in the inductor
 The process repeats in the opposite direction
 There is a continuous transfer of energy between
the inductor and the capacitor
Hertz’s Experimental
Apparatus
 An induction coil is
connected to two
large spheres
forming a capacitor
 Oscillations are
initiated by short
voltage pulses
 The inductor and
capacitor form the
transmitter
Hertz’s Experiment
 Several meters away from the
transmitter is the receiver
 This consisted of a single loop of wire
connected to two spheres
 It had its own inductance and capacitance

 When the resonance frequencies of the

transmitter and receiver matched,
energy transfer occurred between them
Hertz’s Conclusions
 Hertz hypothesized the energy transfer
was in the form of waves
 These are now known to be
electromagnetic waves
 Hertz confirmed Maxwell’s theory by
showing the waves existed and had all
the properties of light waves
 They had different frequencies and
wavelengths
Hertz’s Measure of the Speed
of the Waves
 Hertz measured the speed of the waves from
the transmitter
 He used the waves to form an interference pattern
and calculated the wavelength
 From v = f λ, v was found
 v was very close to 3 x 108 m/s, the known speed
of light
 This provided evidence in support of
Maxwell’s theory
Electromagnetic Waves
Produced by an Antenna
 When a charged particle undergoes an
acceleration, it must radiate energy
 If currents in an ac circuit change rapidly, some
energy is lost in the form of em waves
 EM waves are radiated by any circuit carrying
alternating current
 An alternating voltage applied to the wires of
an antenna forces the electric charge in the
antenna to oscillate
EM Waves by an Antenna,
cont

 Two rods are connected to an ac source, charges oscillate

between the rods (a)
 As oscillations continue, the rods become less charged,
the field near the charges decreases and the field
produced at t = 0 moves away from the rod (b)
 The charges and field reverse (c)
 The oscillations continue (d)
EM Waves by an Antenna,
final
 Because the
oscillating charges in
the rod produce a
current, there is also
a magnetic field
generated
 As the current
changes, the
magnetic field
spreads out from
the antenna
Charges and Fields, Summary
 Stationary charges produce only electric
fields
 Charges in uniform motion (constant
velocity) produce electric and magnetic
fields
 Charges that are accelerated produce
electric and magnetic fields and
electromagnetic waves
Electromagnetic Waves,
Summary
 A changing magnetic field produces an
electric field
 A changing electric field produces a
magnetic field
 These fields are in phase
 At any point, both fields reach their
maximum value at the same time
Electromagnetic Waves are
Transverse Waves
 The E and B fields
are perpendicular to
each other
 Both fields are
perpendicular to the
direction of motion
 Therefore, em
waves are
transverse waves
Properties of EM Waves
 Electromagnetic waves are transverse waves
 Electromagnetic waves travel at the speed of
light
1
c
oo
 Because em waves travel at a speed that is
precisely the speed of light, light is an
electromagnetic wave
Properties of EM Waves, 2
 The ratio of the electric field to the magnetic
field is equal to the speed of light

E
c
B
 Electromagnetic waves carry energy as they
travel through space, and this energy can be
transferred to objects placed in their path
Properties of EM Waves, 3
 Energy carried by em waves is shared
equally by the electric and magnetic
fields
Average power per unit area 
2 2
EmaxBmax Emax c Bmax
 
2 o 2 oc 2 o
Properties of EM Waves, final
 Electromagnetic waves transport linear
momentum as well as energy
 For complete absorption of energy U,
p=U/c
 For complete reflection of energy U,
p=(2U)/c
 Radiation pressures can be determined
experimentally
Determining Radiation
Pressure
 This is an apparatus
for measuring
radiation pressure
 In practice, the
system is contained
in a vacuum
 The pressure is
determined by the
angle at which
equilibrium occurs
The Spectrum of EM Waves
 Forms of electromagnetic waves exist
that are distinguished by their
frequencies and wavelengths
 c = ƒλ
 Wavelengths for visible light range from
400 nm to 700 nm
 There is no sharp division between one
kind of em wave and the next
The EM
Spectrum
 Note the overlap
between types of
waves
 Visible light is a
small portion of
the spectrum
 Types are
distinguished by
frequency or
wavelength
Notes on The EM Spectrum
 Radio Waves
 Used in radio and television communication
systems
 Microwaves
 Wavelengths from about 1 mm to 30 cm
 Well suited for radar systems

 Microwave ovens are an application

Notes on the EM Spectrum, 2
 Infrared waves
 Incorrectly called “heat waves”
 Produced by hot objects and molecules
 Readily absorbed by most materials

 Visible light
 Part of the spectrum detected by the
human eye
 Most sensitive at about 560 nm (yellow-
green)
Notes on the EM Spectrum, 3
 Ultraviolet light
 Covers about 400 nm to 0.6 nm
 Sun is an important source of uv light
 Most uv light from the sun is absorbed in the
stratosphere by ozone
 X-rays
 Most common source is acceleration of high-
energy electrons striking a metal target
 Used as a diagnostic tool in medicine
Notes on the EM Spectrum,
final
 Gamma rays
 Emitted by radioactive nuclei
 Highly penetrating and cause serious
damage when absorbed by living tissue
 Looking at objects in different portions
of the spectrum can produce different
information
Doppler Effect and EM Waves
 A Doppler Effect occurs for em waves, but
differs from that of sound waves
 For sound waves, motion relative to a medium is
most important
 For light waves, the medium plays no role since the light
waves do not require a medium for propagation
 The speed of sound depends on its frame of
reference
 The speed of em waves is the same in all coordinate
systems that are at rest or moving with a constant
velocity with respect to each other
Doppler Equation for EM
Waves
 The Doppler effect for em waves
 u
f '  f 1  
 c
 f’ is the observed frequency
 f is the frequency emitted by the source
 u is the relative speed between the source and the
observer
 The equation is valid only when u is much smaller
than c
Doppler Equation, cont
 The positive sign is used when the object
and source are moving toward each other
 The negative sign is used when the object
and source are moving away from each
other
 Astronomers refer to a red shift when
objects are moving away from the earth
since the wavelengths are shifted toward
the red end of the spectrum