Heodolite Ntroduction: Presented at Civil

THEODOLITE: INTRODUCTION
Presented @ Civil
INTRODUCTION
 Theodolite is used to measure the horizontal and
vertical angles.
 Theodolite is more precise than magnetic compass.
 Magnetic compass measures the angle up to as

accuracy of 30’. However a vernier theodolite
measures the angles up to and accuracy of 10’’, 20”.
 There are variety of theodolite vernier, optic,

electronic etc.
TYPE OF THEODOLITE
Vertical axis
VERNIER THEODOLITE
Traverse/horizontal axis
Vertical circle rigidly fixed to
the telescope
Line of Sight
Alidade assembly
 Vernier theodolite is
also known and
transit.
Horizontal circle
assembly
 A transit theodolite is
one in which the
Levelling head assembly
telescope can be
rotated in a vertical
plane.
Three assemblies of Theodolite
 Main parts of a theodolite
 Levelling head (7): Levelling
head is used to attach the
instrument to tripod and attach
the plumb bob along the vertical
axis of the instrument.
MAIN PARTS-2
 Lower plate/circle plate (18): an annular
horizontal plate with the graduations
provided all around, from 0 to 360°, in a
clockwise direction. The graduations are in
degree divided in to 3 parts so that each
division equals to 20 min.
 Horizontal angles are measured with this

plate.
 The size of the theodolite is defined by the

diameter of horizontal circle.
 Upper plate (17): Horizontal plate of

smaller diameter provided with two verniers.
on diametrically opposite parts of its
circumference. These verniers are designated
as A and B. They are used to read fractions
of the horizontal circle plate graduations.
The verniers are graduated in 20 min and
each minute is divided in 3 to 5 parts making
least count 20” or 10”.
MAIN PARTS-3
 Clamps and tangent screws (15, 19):
 There are two clamps and associated
tangent screws with the plate. These screws
facilitate the motion of the instruments in
horizontal plane.
 Lower clamp screw locks or releases the

lower plate. When this screw is unlocked
both upper and lower plates move together.
The associated lower tangent screw allows
small motion of the plate in locked position.
 The upper clamp screw locks or releases the

upper vernier plate. When this clamp is
released the lower plate does not move but
the upper vernier plate moves with the
instrument. This causes the change in the
reading. The upper tangent screw allows
the fine adjustment.
MAIN PARTS-4
 Plate level (5):

 Spirit level with the bubble and
graduation on glass cover.
 A single level or two levels fixed in
perpendicular direction may be
provided.
 The spirit level can be adjusted with
the foot screw (21) of the levelling
head (7).
 Telescope (10): The essential parts of

the telescopes are eye-piece, diaphragm
with cross hairs, object lens and
arrangements to focus the telescope.
MAIN PARTS-5
 Vertical circle (1): circular plate

supported on horizontal axis of the
instrument between the A-frames.
Vertical circle has graduation 0-90 in
four quadrants. Vertical circle moves
with the telescope when it is rotated
in the vertical plane.
 Vertical circle clamp and tangent

screw (11): Clamping the vertical
circle restrict the movement of
telescope in vertical plane.
 Altitude level (2): A highly sensitive

bubble is used for levelling
particularly when taking the vertical
angle observations.
Reading a
theodolite
Vernier scale graduation

Important Definition
Changing face
 Revolving the telescope by 180° in vertical plane
about horizontal axis
 Again revolving the telescope in horizontal plane
about vertical axis.
Adjustment of the theodolite
 Temporary Adjustment
 Setting up the theodolite

Measurement of horizontal angle
 Measurement of Angle ABC
 The instrument is set over B.
 The lower clamp is kept fixed and upper clamp is
loosened.
 Turn the telescope clockwise set vernier A to 0° and
vernier B to approximately 180°.
 Upper clamp is tightened and using the upper tangent
screw the vernier A and B are exactly set to 0° and
180°.
 Upper clamp is tightly fixed, lower one is loosened and
telescope is directed towards A and bisect the ranging
rod at A.
 Tightened the lower clamp and turn the lower tangent
screw to perfectly bisect ranging rod at A.
 Loose the upper clamp and turn the telescope clockwise
to bisect the ranging rod at C tightened the upper clamp
and do the fine adjustment with upper tangent screw.
 The reading on vernier A and B are noted. Vernier A
gives the angle directly and vernier B gives the reading
by subtracting the initial reading (180°) from final
 Read these two method
 Repetition method
 Reiteration method
Vertical angle measurement-1
Vertical angle measurement-2
 Measurements of
 Deflection angle
P
 magnetic bearing
B

N
B C
A
 Read assignment (N. N. Basak, S. K. Duggal)
 Ranging and extending a line
 Method of traversing
 Included angle method
 Deflection angle method
 Fast angle (or magnetic bearing method)
Computation of latitude and departure
 Latitude of a line is the distances measured
parallel to the north south of the North-South
direction
 Departure of the line is the distance measured
parallel to the east-west direction
Computing latitude and departure
PROBLEM-1
 While making survey through the woods, a surveyor with the hand
compass started from point A and walked a thousand steps in the direction
S67⁰W and reached a point B. then he changed his direction and walked
512 steps in the direction N10⁰E and reached a point C then again he
changed his direction and walked 15 04 steps in the direction S65⁰E and
reached a point D as shown in Figure Now the surveyor wants to return to
the starting point A. In which direction should he move and how many
steps should he take.
Sources of errors in theodolite
 Instrumental errors
 Non adjustment of plate bubble
 Line of collimation not being perpendicular to
horizontal axis
 Horizontal axis not being perpendicular to vertical
axis
 Line of collimation not being parallel to axis of
telescope
 Eccentricity of inner and outer axes
 Graduation not being uniform
 Verniers being eccentric
 . Personal errors
 Natural errors
 High temperature causes error due to irregular refraction.
 High winds cause vibration in the instrument, and this may
lead to wrong readings on verniers
 Closing error
Balancing of traverse
 Bowditch’s rule:
 Total error is distributed in proportion to the lengths of the
traverse legs.
Calculation of traverse area
PROBLEM
 Calculate the latitudes, departures and closing
error for the following traverse conducted at
allahabad. Adjust also the traverse using
Bowditch’s rule.
Line Length WCB
AB 89.31 45⁰ 10’
BC 219.76 72⁰ 05’
CD 151.18 161⁰ 52’
DE 159.10 228⁰ 43’
EA 232.26 300⁰ 42’

Heodolite Ntroduction: Presented at Civil

Uploaded by

Copyright:

Available Formats

Heodolite Ntroduction: Presented at Civil

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Heodolite Ntroduction: Presented at Civil

Uploaded by

Copyright:

Available Formats

THEODOLITE: INTRODUCTION

 Theodolite is more precise than magnetic compass.

 Magnetic compass measures the angle up to as

 There are variety of theodolite vernier, optic,

 Horizontal angles are measured with this

 The size of the theodolite is defined by the

 Upper plate (17): Horizontal plate of

 Lower clamp screw locks or releases the

 The upper clamp screw locks or releases the

 Plate level (5):

 Telescope (10): The essential parts of

 Vertical circle (1): circular plate

 Vertical circle clamp and tangent

 Altitude level (2): A highly sensitive

Vernier scale graduation

 Setting up the theodolite

You might also like