GEOTECHNICAL ENGINEERING – II

(FOUNDATION ENGINEERING)

Prepared by:
Mc-Lloyd G. Sarate
Cantilever Sheet Piles
. Pa = γs ( h+ d )
Ka
2
Pp = γs d² Kp
h
2
Pa
Pp Ka = 1 - Sin θ
d h+d
3 1 + Sin θ
A
d/3 Kp = 1 + Sin θ
1 - Sin θ
Cantilever Sheet Piles
ΣMA = 0

Pp d = Pa h + d
3 3

θ = angle of internal friction

Pa = active force
Pp = passive force
Ka = active pressure coefficient
Kp = passive pressure coefficient
A sheet pile acting acting as a cantilever retaining wall, retains a
soil that 2 m. high with an angle of friction of 30 deg and a unit
weight of 18 kN/m3.
1) Determine the required depth of penetration with 20
percent allowance for shear development. Assume that the
pivot is at the foot of the pile.
2) Determine the total active force on the sheet pile.
3) Determine the total passive force on the sheet pile

2m

Pa
Pp (2+d)/3
d
A
d/3
 Solution ΣMA = 0

1 Depth of penetration:
Ka = 1 - Sin θ
1 + Sin θ
Ka = 1/3

Kp = 1 + Sin θ
1 - Sin θ 2
Kp = 3

3
A cantilever sheet pile is 8.2 m. long with a depth of embedment
3.2 m. An angle of friction of the soil supported by the sheet
pile is 34deg and has a unit weight of 1.91 g/cc. There is water
table below the base of the sheet pile. γw = 9.81 kN/cu.m
1. Compute the active force acting on the sheet pile.
2. Compute the passive force acting on the sheet pile
3. Compute the theoretical passive force that must be
mobilized to ensure stability.

γs = 1.91 g/cc θ = 34 deg

θ = 34 deg. 5 γs = 1.91 g/cc
5m γs = 1.91 (9.81)
γs = 18.74 kN/cu.m
8.2m
3.2 Pa
3.2m Pp 8.2m
Solution
1. Active Force
Ka = 1 - Sin 34 Pp = 1 γs h² Ka
2
1 + Sin 34
1 (18.74)(3.2)²(3.53)
Ka = 0.283 2
Pa = 1 γs h² Ka Pp = 338.70 kN/m
2
1 (18.74)(8.2)²(0.283) 3. Theoretical passive force to
2
Pa = 178.3 kN/m ensure stability
ΣMA = 0
2. Passive Force Pp d = Pa h
Kp = 1 + Sin 34 3 3
Pp 3.2 = 178.3 8.2
1 - Sin 34
3 3
Kp = 3.53 Pp = 456.9 kN/m
Anchored Sheet Pile Walls
 Anchored sheet pile walls are held above the driven depth by
anchors provided at suitable level
 The anchors provide forces for the stability of the sheet pile, in
addition to the lateral passive resistance of the soil into which
the sheet piles are driven.
Anchored Sheet Pile Walls
It includes an anchor or tieback at or near the head of the wall.
More than one set of anchors or tiebacks can be used. It
increases wall stability and enables taller walls to be built and
sustained almost a necessity with vinyl, aluminium and
fiberglass sheet piles. It is not exclusive to sheet piling; also used
with other types of in situ wall systems. In case of cantilever
sheet pile walls if the deflection at top point of the sheet pile
wall is very large, then settlement of soil takes place at top just
behind the sheet pile wall. So, to reduce the excessive
deflections the anchors are provided.
Different types of anchored
sheet pile walls:
Types of Anchored Sheet Pile Walls
1. Free earth support piles,
2. Fixed earth support piles
Free earth support piles

An anchored sheet pile is said to have free earth support

when the depth of embedment is small and pile rotates at
its bottom tip. Thus, there is no point of inflection in the
pile. It is assumed that

 The base of the pile is relatively free to move, so passive

resistance is mobilized on one face only.
 The lateral pressure increases linearly with depth.
 Wall friction is negligible.
Free earth support piles
Fixed earth support piles

An anchored sheet pile is said to have free earth support

when the depth of embedment is large and the bottom tip
of the pile is fixed against rotation. Thus, there is change in
curvature of pile, hence inflection point occurs. It is
assumed that

 The base of the pile is relatively fixed, so that there is a

point of contra-flexure above the toe of the pile.
 Passive resistance is mobilized on both faces (similar to
cantilever pile).
 The lateral pressure increases linearly with depth.
 No wall friction.
Fixed earth support piles
Comparison between fixed earth method and free earth
method
• The free earth support method gives a pressure distribution
that would apply when the wall is on the point of failure by
rotation about the anchor.
• The fixed earth support method is unlikely to represent the
true loading at any stage.
• Both methods tend to over-estimate the bending moment in
the pile.
• The free earth support method is simpler.
• In the fixed earth support, depth provided is more, moment
through out the section reduces, so thiner section is to be
provided.
• In the free earth support, depth provided is less, moment
through out the section is more than fixed earth support, so
thicker section is to be provided.
Design of sheet pile wall by free earth support
The figure shows the condition for the free earth support. The
deflection of the bulk head is some what similar to that of a
vertical elastic beam whose lower end B is simply supported and
the other end is fixed. The forces acting on the sheet pile are :
 Active pressure due to soil behind pile,
 Passive pressure due to soil in front of the pile,
 The tension in the anchor rod.
Cohesionless soil ( free earth support )
The forces acting on the wall are shown in the fig. Assuming that
the material above and below dredged level in cohesionless.
From horizontal equilibrium

Where,
T is the tensile force in the anchor
is the resultant earth pressure acting below the dreaged level
for b height of the wall
is the resultant earth pressure acting for (h+a)
heigth of the wall

The depth a to the point of zero pressure can be determined by

equating the earth pressure on both the side of the sheet pile.
Taking moments of all forces about anchor point M,

Where,
a is the distance of the zero earth pressure point below dredged
level

h is height of the sheet pile above the dredged level,

e is the distance of the anchor from the top level of sheet pile,
generally taken as 1 to 1.5 m

Z1 is the distance between point of application force P1

and O point
Substituting the value of P2 in the above equation,
Cohesive soils ( free earth support )
Consider the case, the sheet pile is driven in clay (θ = 0), but has
the backfill of cohesionless soil as shown in fig. The earth
pressure distribution above the dredged line is same as that in
case of cohesionless soil. However the pressure below the
dredge line at any point at a distance of z from dredged level is
given as,

Where:
h is the height of the sheet pile above the dredged level
c is the cohesion
γ is the unit weight of the soil
Cohesive soils ( free earth support )
Taking moments of all the forces about M,

Substituting the value of = 4c – h in the above equation,

Where:
g is the distance of the tendon above dredged level,
f is the distance between the point of application of force
P1 and tendon (M) = g – Z1
Design of sheet pile wall by free earth support

The elastic line changes its curvature at the inflection point I. the
soil into which the soil is driven exerts a large restraint on the
lower part of the pile and causes the change in the curvature.
The distance of the inflection point below dredged level (i) can
be related to the internal friction angle (θ) as given in table 1.
Where

h is the height of the sheet pile wall above the dredged level
As exact analysis of the anchored sheet pile with fixed earth
support is complicated, an approximate method known as
equivalent beam method is generally used. It is assumed that
the sheet pile is a beam which is simply supported at anchor
point M and fixed at the lower end K. Figure shows the bending
moment diagram. The bending moment is zero at the inflection
point I. The beam is divided into two parts as shown in figure.
The following procedure is used for the analysis:
Equivalent beam method
Moment reduction for anchored wall
Rowe (1952) demonstrated that the Free Earth method
overestimates the maximum bending moment in anchored walls
with horizontal tie rods. The sheet piles are relatively flexible
and these deflect considerably. Their flexibility causes a
redistribution of the lateral earth pressure. The net effect is that
the maximum bending moment is considerably reduced below
the value obtained for the free earth supports. It is used to take
into consideration the flexibility of the pile and its effect on
relieving the actual bending moment the wall experiences. The
reduced bending moment for design ( ) is given by
Mdesign = MMAX Rm
Where
Mmax = maximum bending moment predicted by the
Free Earth method,
Rm = reduction factor depending on wall geometry,
wall flexibility, and foundation soil characteristics.
Moment reduction factor for granular foundation soils.
When the soil below the dredge line is granular, the
magnitude of the reduction factor Rm is a function of a
flexibility number given by

where,
H = total length of the sheet piling (ft),
E = modulus of elasticity of the pile material (psi),
I = moment of inertia (in 4 ) per foot of wall.

Curves of Rm are given in fig. for "loose" and "dense"

foundation material and several system geometries
Moment reduction factor for cohesive foundation soils. Moment
reduction factors for piles in homogeneous cohesive soils also
depend on the stability number ( Sn ) given by

where,
c = cohesive strength of the soil
Pv = effective vertical soil pressure on the retained side of the
wall at the elevation of the dredge line.
The curves for Rm are given for various combinations of system
parameters in Figure

Rowe's moment reduction coefficients for

sand (after Bowles, 1982)
Rowe's moment reduction coefficients
for clays (after Bowles, 1982)
Problem: An anchored sheet pile wall supports a mass of soil 7.3
m. high with a horizontal surface. The angle of friction of the soil
is 31deg. with the unit weight of 1.96 g/cu.cm. The total height
of the sheet pile is 10.5 m. which is supported by an anchor bolt
placed 1.2 m. below the ground surface which has a spacing of 3
m. center to center.
1.Compute the active force.
2.Compute the fraction of the 1.2 θ = 31 deg
γs = 1.96g/cucm
theoretical maximum passive
resistance of the total embedded Anchor bolt
10.5
length which must be mobilized
for equilibrium. 7.3

3.Compute the tension in the

anchor bolt.
Solution:
1.Active force:
Ka = 1-sin31
1+sin31
θ = 31 deg
Ka = 0.32 1.2
γs = 1.96g/cucm
P1 = 1 γs h² Ka
A T
2 10.5
γs = 1.96(9.81)(100)3 5.8
7.3
1000 8.23 6.1
P1
γs = 19227.6N/m3
P1 = 1 (19.23)(10.5)²(0.32)
2
P1 = 339.22 kN/m
2.Fraction of the theoretical maximum passive resistance of the
total embedded length which must be mobilized for
equilibrium:
ΣMA = 0 Fraction of theoretical max.
passive resistance
P1(5.8) = P2(8.23)
= 2.43 = 0.78
339.22(5.8) = P2(8.23) 3.12
P2 = 239.06kN
P2 = 1 γs h² Kp 3.Tension on anchor bolts:
2 T = P1 - P2
239.06 = 1 (19.23)(3.2) Kp T = 339.22 – 239.06
T = 100.16 kN/m
2
T = 300.48 kN
Kp = 2.43
Max.value of Kp for θ = 31deg
Kp = 1+sin31
1-sin31
Kp = 3.12
THANK YOU!