Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 39 views

    Emcp Ii

    Uploaded by

    Aziz Arrahal
    The document discusses an EMCP control panel used for engine and generator protection. The EMCP uses a microprocessor to perform the functions of relays and timers in previous control panels. It monitors engine parameters and controls start/stop, and has features like fault codes and programming modes.

    Copyright:

    © All Rights Reserved
    Download as PPT, PDF, TXT or read online from Scribd

    Emcp Ii

    Uploaded by

    Aziz Arrahal
    39 views14 pages
    The document discusses an EMCP control panel used for engine and generator protection. The EMCP uses a microprocessor to perform the functions of relays and timers in previous control panels. It monitors engine parameters and controls start/stop, and has features like fault codes and programming modes.

    Original Title

    174526413-EMCP-II

    Copyright

    © © All Rights Reserved

    Available Formats

    PPT, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document discusses an EMCP control panel used for engine and generator protection. The EMCP uses a microprocessor to perform the functions of relays and timers in previous control panels. It monitors engine parameters and controls start/stop, and has features like fault codes and programming modes.

    Copyright:

    © All Rights Reserved
    Download as PPT, PDF, TXT or read online from Scribd
    Download as ppt, pdf, or txt
    39 views14 pages

    Emcp Ii

    Uploaded by

    Aziz Arrahal
    The document discusses an EMCP control panel used for engine and generator protection. The EMCP uses a microprocessor to perform the functions of relays and timers in previous control panels. It monitors engine parameters and controls start/stop, and has features like fault codes and programming modes.

    Copyright:

    © All Rights Reserved
    Download as PPT, PDF, TXT or read online from Scribd
    Download as ppt, pdf, or txt
    of 14

    EMCP II

    Control panel
    In previous generator control panels, relay are used in
    conjunction with switches to make a logic panel to protect
    the engine and generator.
    T0 T1 T2 T3

    Actuator
    MP

    Engine Diode

    The typical logic, uses a signal to start the engine


    and a magnetic pickup that feed the ESS
    EMCP
    The EMCP uses a similar type of logic but a microprocessor GSC
    performs the functions of all the relays and timers used before.
    They are : EMCP I , EMCPII, EMCPII +, EMCPII + P

    GSC
    Engine monitoring :
    System DC voltage
    Engine RPM
    Oil pressure
    EMCP Features
    Engine hour meter
    Coolant temperature Cooldown timer

    Optional: System diagnostics


    Coolant loss
    Exhaust temperature Diesel and gas engine functionality

    Start/Stop control Various system fault codes

    Cycle cranking Engine set point programming

    AC monitoring Engine set point verification


    AC voltage
    AC current
    Frequency
    Fault Indicators
    • Fault alarm indicator
    • Fault shutdown indicator
    • Dedicated shutdown indicator
    -Low Oil Pressure
    -Emergency Stop
    -High Water Temp
    -Engine Overspeed
    -Low Coolant Level
    -Overcrank
    Relays
    • K1-Electronic Governor Relay.
    • K2-Generator Fault Relay.
    • K3-Crank Termination Relay.
    • K4-Starting Motor Relay.
    • K5-Run Relay.
    • K6-Air Shutoff Relay.
    • K7-Fuel Control Relay.
    Modes of Operation
    • Normal Mode
    • Alarm Mode
    • Shutdown Mode
    • Service Mode
    Engine Starting Sequence
    Check sys for faults,
    engine is not already
    running, not in service
    mode

    Activate
    SMR, FCR

    Activate EG relay
    – oil press=set point Deactivate
    for low oil press. SMR
    Start or remote signal -rpm=400
    & Activate CTR
    Note: -FCR energize to run (K4, K5, K7) or to stop (K4, K5)
    -The relay status on the relay status indicators of the lower display.
    K1, K3, K5, K7 for ETR ; K1, K3, K5 for ETS
    Engine Stopping Sequence
    Check sys for faults,
    begin the cool down
    time, and activate
    the spare output (if
    programmed)
    Deactivate
    RR & EGR
    oil press<set point
    for low oil press.

    *
    Deactivate 0r activate
    Deactivate
    FCR
    Stop or remote signal CTR
    (RPM = 0)

    * Note: The relay status on the relay status indicators of the lower display.
    all relays are Off except on ETS K7 indicator remain On for 70 sec after 0 rpm
    and oil press is also 0
    Service Mode
    • Assist with troubleshooting
    • Satisfy special applications
    • Satisfy customer needs
    • Verify or calibrate or adjust genset functions
    OP1 PHASE ENGINE LAMP ALARM
    EXIT
    SERVICE
    SELECT METER TEST CODE MODE

    SCROLL SCROLL SCROLL SELECT ENTER


    RIGHT UP DOWN

    OP1 FAULT LOG VIEWING


    Service mode
    OP4 Fault log programming
    OP2 SETPOINT VIEWING
    OP5 Set point programming
    OP3 PASSWORD ENTRY
    OP6 Spare Input/Output programming

    OP7 Hourmeter programming

    PE: 13231 OP8 Voltmeter/Ammeter programming

    OP9 Engine setpoint verification

    OP10 AC calibration

    You might also like