PSA Reporting

Operational Power
Control Systems
IMPORTANT TERMS
Chapter 16 deals with operational power control systems. After
studying this chapter, you should have an understanding of the following terms:
• Start-Stop Pushbutton
• Normally Open (NO) Pushbutton
• Normally Closed (NC) Pushbutton
• Overload Protection
• Jogging
• Limit Switch
• High-Low Speed Selection
• Magnetic Contactor
• Full-Voltage Starting
• Primary Resistance Starting
• Primary Reactor Starting
• Wye-Delta Starting
• Autotransformer Starting
• Part-Winding Starting
• Direct Current (DC) Starting Systems
• Forward-Reverse-Stop Control
• Three-phase Alternating Current (AC)
Motors
• Single-phase AC Motors
• DC Motors
• Motor Starting Protection
• Dynamic Braking
• Speed Control Circuits
• Frequency Conversion Systems
• Programmable Logic Controller
BASIC CONTROL SYSTEMS
Electrical power control systems are used with many types of
loads. The most common electrical loads are motors, so our
discussion will deal mainly with electric motor control.
However, many of the basic control systems are also used to
control lighting and heating loads. Generally, the controls for
lighting and heating loads are less complex
MOTOR-STARTING SYSTEMS
Types of Starting Systems
Motor starting, particularly for large motors, can play an important role in the efficient
operation of an electrical power system. There are several systems used to start electric
motors. The motor-starting equipment that is used is placed between the electrical power
source and the motor.
Full-voltage Starting
One method of starting electric motors is called full-voltage starting. This method is the least
expensive and the simplest to install. Since full power-supply voltage is applied to the motor
initially, maximum starting torque and minimum acceleration time result. However, the
power system must be able to handle the starting current drawn by the motor
Primary Resistance Starting

Another motor starting method is called primary resistance starting. This method uses
resistors in series with the power lines to reduce the motor-starting current. Ordinarily, the
resistance connected into the power lines may be reduced in steps until full voltage is applied
to the motor. Thus, starting current is reduced according to the value of series resistance in
the power lines
SPECIALIZED CONTROL
SYSTEMS
Electrical power control is usually desired for some specific
application. In this section, we will discuss some common types of
specialized, electrical power control systems that are used today.
Forward and Reverse Operation of Motors

Most types of electrical motors can be made to rotate in either
forward or reverse direction by some simple modifications of their
connections. Ordinarily, motors require two magnetic contactors to
accomplish forward and reverse operation.
DC Motor Reversing
DC motors can have their direction of rotation reversed by changing
either the armature connections, or the field connections to the power
source
Single-phase Induction Motor Reversing

If we modify the diagram by replacing the shunt field coils with the run
windings, and the armature with the start windings, directional reversal
of a single-phase AC motor can be accomplished. Single-phase
induction motors are reversed by changing the connections of either the
start windings or the run windings, but not of both at the same time.
Three-phase Induction-Motor Reversing

Three-phase motors can have their direction of rotation reversed by
simply changing the connections of any two power input lines
FREQUENCY-CONVERSION
SYSTEMS
The power system frequency used in the United State is 60
hertz, or 60 cycles per second. However, there are specific
applications that require other frequencies in order to
operate properly. Mechanical frequency converters may be
used to change an incoming frequency into some other
frequency. Frequency converters are motor/generator sets
that are connected together, or solid-state variable
frequency drives.
Synchronous units, such as the one shown, are used wherever
precise frequency control is required. It is also possible to design
units that are driven by induction motors, if some frequency
variation can be tolerated. Variable frequency drives are now being
used to control many types of industrial machinery. They are used
because they are not as expensive as variable speed controllers have
been in the past.
PROGRAMMING THE PLC
Instructions for the operation of a programmable logic

controller are given to the PLC through pushbuttons, a
keyboard programmer, magnetic disks, or cassette tape. Each
PLC has a special set of instructions and procedures that
makes it functional. How the PLC performs is based on the
design of its programming procedure. In general, PLCs can
be programmed by relay ladder diagrams or logic diagrams.
These procedures can be expressed as language words or as
symbolic expressions on a CRT display.
Assembly Language
Assembly language is a basic instructional set that is specific to
the type of the microprocessor used in the construction of the PLC. For one type
of microprocessor, the assembly language program is a combination of
mnemonics and labels that the programmer uses to solve a control problem
Relay Language or Logic

The processor of a programmable logic controller dictates the
language and programming procedure to be followed by the system.
Essentially, it is capable of doing arithmetic and logic functions.
Programming Basics Programmable

logic controllers are provided with the capability to program or simulate the
function of relays, timers, and counters. Programming is achieved on a format of
up to 10 elements in each horizontal row or rung of a relay diagram, and up to
seven of these rungs may be connected to form a network.
THANKYOUUUU

PSA Reporting

Uploaded by

Copyright:

Available Formats

PSA Reporting

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

PSA Reporting

Uploaded by

Copyright:

Available Formats

Operational Power

Primary Resistance Starting

Forward and Reverse Operation of Motors

Single-phase Induction Motor Reversing

Three-phase Induction-Motor Reversing

Instructions for the operation of a programmable logic

Relay Language or Logic

Programming Basics Programmable

You might also like