Wall
Wall
Wall
construction iii
WALL SYSTEMS
1. INTRODUCTION
A wall is a continuous, usually vertical structure of brick, stone,
block, concrete, timber, or metal thin in proportion to its height and
length.
2
WALL SYSTEMS
1. INTRODUCTION (cont...)
The functional requirements of a wall are:
Strength and stability
Resistance to weather
Durability and freedom from maintenance
Fire resistance
Resistance to passage of heat
Resistance to passage of sound
3
2. TYPES OF WALLS
A distinction between various types of wall can be made in two different
ways:
4
2. TYPES OF WALLS (CONT...)
Foundation walls
The function of foundation wall is to transmit loads coming
from the super structure.
Basement walls
The function of basement wall is to:
• Support vertical loads (if load bearing)
• Resist lateral loads, and
• Protect the building from dampness.
5
2. TYPES OF WALLS (CONT...)
External walls:
Must provide protection against wind and rain, should insulate heat
Be water repellent, fire resisting and capable of sound insulation.
Internal walls:
Internal walls are basically required to separate rooms.
They should have sufficient sound and heat insulating capacity and should
be water repellent.
6
Load bearing walls:
The strength must be sufficient to carry the loads placed on
it.
The loads are calculated from the live and dead loads on the
structure supported by the wall
wind pressure must also be taken into
account.
3.2 TYPES OF EXTERNAL WALLS
External walls can be classified in different groups according to their
structural functions and physical nature.
nature
8
3.2.1 WALLS OF BLOCK CONSTRUCTION
Walls composed of stones, bricks or HCB are of block
construction.
They are formed from fairly small units set in matrix of cement
mortar.
9
A) BRICK WALLS
Brick walls are widely used both as load bearing and as non-load
bearing walls.
Brick is a very old building material.
10
A) BRICK WALLS (CONT...)
Brick masonry
Brick masonry is sometimes preferred over other types of masonry for the
following reasons:
Bricks are of uniform size and shape, and hence they can be
laid in any definite pattern.
Bricks are light in weight and small in size. Hence they can be
easily handled.
Brick do not need any dressing.
The art of brick laying can be understood easily.
Ornamental works can be easily done with bricks.
Light partition walls can be easily constructed in brick
masonry.
11
A) BRICK WALLS (CONT...)
Types of brick bonds
Bond is the system of laying bricks in such a manner that there is no
vertical joint in any row or course immediately above or below the one
considered.
i. Stretcher bond
Is the one in which all the bricks are laid as stretchers on the faces of the
wall.
This pattern is used only for those walls which have thickness of half
brick. Used as partition walls, sleeper walls, chimney stacks, etc
12
A) BRICK WALLS (CONT...)
Types of brick bonds (cont...)
ii. Header bond
Is the one in which all the bricks are laid as headers on the faces of walls.
The width of the brick is along the direction of the wall.
The pattern is used only when the thickness of the wall is equal to one
brick.
This bond does not transmit pressure in the direction of the length of the
wall. Thus it is unsuitable for load bearing walls.
13
A) BRICK WALLS (CONT...)
Types of brick bonds (cont...)
iii. English bond
This is the most commonly used bond, for all wall thickness. And it is
considered to be the strongest.
The bond consists of alternate courses of headers and stretchers.
The vertical joints of the header courses come over each other, the same
goes for stretcher courses.
14
B) STONE WALLS
The stones used for masonry should be hard,
hard durable,
durable tough and sound
and free from weathering, decay or defects like cavities, cracks, sand holes,
injurious veins, patches of loose or soft materials etc.
Rocks from which building stones are obtained, are divided into three
groups:
i. Igneous rock:
rock the chief building stones in this class are trachyte,
basalt, granite, etc.
ii. Sedimentary rocks:
rocks The principal building stones in this group are
lime stones and sand stones. These are used in floors, steps, facing
works, columns, walls etc.
iii. Metamorphic rocks:
rocks the common building stones are slate and
marble. Since marble is costly it is not used for masonry but used
for flooring, facing work, steps, ornamental works etc.
15
DRESSING OF STONES
The surface of stones obtained from quarry are rough. The blocks are
irregular in shape and non uniform in size. Hence their dressing is
essential.
It serves the following purposes:
i. It gives desired aesthetic appearance.
ii. It makes transport easy and economical.
iii. It suits the desired requirements.
iv. It helps taking advantage of locally available skilled labour
16
DETERIORATION OF STONES
Various environmental and external agencies play an important role
to deteriorate the stones:
i. Alternate heating and cooling:
cooling Repeated contraction and
expansion cause cracking of stones due to internal stresses.
ii. Alternate wetting and drying:
drying repeated wetting and drying
result in wearing it out quickly.
iii. Thawing and freezing:
freezing it results in entrapping of moisture
which expand on freezing resulting in splitting of stones.
iv. Nature of mortar:
mortar The mortar may react chemically with
constituents of stone and leads to the disintegration of stones
v. Rain water:
water
vi. Vegetable growth:
growth
17
C) CONCRETE BLOCK WALLS
One of the most common masonry units.
It consists of hardened cement and may be completely solid or contain
single or multiple hollows.
It is made from conventional cement mixes and various types of
aggregates. These include: sand, gravel, crushed stone, expanded shale or
clay, volcanic ciders (Pozzolana), scoria, pumice, etc.
Various types of blocks are manufactured to be used for wall construction.
18
Thank you!!!