Prismic A30

PRISMIC A30
Excitation Controller
Introduction
The PRISMIC A30 excitation controller is designed to control the excitation of a brushless generator. Incorporating a wide range of features, the A30 is housed in a 19 rack assembly requiring only external instruments and control switches to provide the complete excitation system as shown in Fig. 1 below. For commissioning of the A30, a PC is required. PC based software and two serial communications cables are provided.
PRODUCT SPECIFICATION
Features
Pilot Exciter Brushless Synchronous AC Generator Voltage Transformer Instrument Current Transformer
Complete System Housed in a Single 19 6U rack. The rack incorporates: Power supply transformers Power semiconductors Control circuits Excitation changeover contactor Field suppression contactor and resistor
Isolator
Exciter Exciter Field FSR

EXTERNAL CONTROLS: Excite/Suppress
Independent Main and Hot Standby Excitation Channels. The unit contains two power semiconductor circuits, one acting as a hot standby to the other. Each circuit is controlled by an independent control card with automatic tracking to enable smooth transfer from one to the other. Transfer to the standby system is initiated by a separate monitor module in the following circumstances: Voltage monitoring (over/under voltage on generator terminals) Excitation monitoring (over/under excitation with time delays) The settings for the monitor module are selected to enable the normal limiter settings to operate first. (see Fig.2, Generator Capability Diagram, overleaf). PC-based Setup and Maintenance Software. The unit is provided with PC based setup and maintenance software and cable for connection to a standard PC 9-pin COM port. A PC is required to set up the A30.
FSC
Main Channel
ECC
Main/Standby Selector Set Voltage Datum Set PF/VAr Datum Select PF/VAr/VAr Shed
Standby Channel
Set Voltage Datum
Communication Ports for Commissioning & Diagnostics
Monitor
Monitor Inhibit EXTERNAL CONNECTIONS: Null Balance Meter (Standby & Auto Matched) RELAY CONTACTS: Diode Failure Alarm Limiter Operating Monitor Tripped Field Contactor Closed Main/Standby Selected Auxiliary DC Supply Healthy General Alarm
PRINCIPAL INDICATIONS: Power Supplies Healthy Individual Monitor Status Individual Limiter Status Diode Failure Alarm PF/VAr/VAr Shed Selected Standby at Minimum Auto/Standby High/Low Main Channel Watchdog Monitor Watchdog
Fig 1. A30 Excitation Controller Scheme
Soft Start Facility Under normal operation, as the generator approaches rated speed, the line voltage is increased at an adjustable, controlled rate to the required setpoint. Fast Acting Field Current Limiter Limits excitation current to prevent excessive line current during power system faults. Over Excitation Limiter Using inverse time delay and temperature compensation if required, this facility is provided to prevent overheating of the generator rotor.
Fig. 2 Generator Capability Diagram
Features (continued)
Communication Port #1 for Setup and Maintenance. Provided for connection to an RS232 port on a standard PC for commissioning. Communication Port #2 for SCADA Communications. Provided to allow plant supervision computers to adjust setpoints and inspect generator and excitation system data. Implemented using Modbus protocol. Choice of Setpoint Adjustment Method. Either external raise/lower contacts or SCADA communications may be used.
Operating Modes Line Voltage Control In line voltage control mode, line voltage is controlled to a constant adjustable setpoint. In this mode, parallel running capability is provided using quadrature current compensation (QCC) with an adjustable droop setting. Power Factor Control Available when parallel running. VAr Control Available when parallel running. Also incorporates VAr shed facility.
Under Excitation Limiter This facility enables operation of the generator at maximum capability with a leading power factor whilst avoiding the risk of the rotor pole slipping. Over Flux Limiter Excitation is controlled to ensure that, with low frequency, generator line voltage is limited to a preset adjustable voltage/frequency ratio to avoid over fluxing of the generator. Selectable Standby System Control Mode The standby system may be set up to operate in either generator voltage or exciter field current control mode. Rotating Diode Failure Alarm Detection of a failed rotating diode or fuse is achieved by monitoring the exciter field current. Adjustable Step Response This facility enables an adjustable step change in setpoint to be applied to evaluate the stability settings of the excitation system. The PID parameters of the excitation controller may then be adjusted accordingly. The rise time and overshoot values are recorded to help with commissioning. Event Recorder A log of major events, such as limiter operations, field suppression and transfers, is maintained within the unit. The events may be displayed using a PC connected to the commissioning port.
Ratings
Maximum continuous output current Maximum 10 second output current Excitation supply voltage Excitation supply frequency Nominal sensing voltage Control power supply Voltage sensing phases Nominal generator frequency Current transformer input nominal Current transformer input burden Load taken by sensing inputs Maximum field voltage for forcing Voltage adjustment range Accuracy of control Operating temperature range Storage temperature range Dimensions Weight 20A 30A Single phase 110V to 330V 50Hz to 480Hz 100V to 120V selectable in 5V steps 24V dc, alternatively 110V dc Three phase with single phase option 50Hz or 60Hz 5A or 1A selectable Less than 1VA Less than 2VA 75% of the available single phase rms supply voltage Selectable from +/-10% to +/-25% +/- 0.5% 0C to +55C -40C to +100C Width 483mm, height 266mm, depth 400mm 14.5kg
Certificate No 21024
BRUSH ELECTRICAL MACHINES Ltd Falcon Works, Nottingham Road, Loughborough, Leics. LE11 1EX England Tel: +44 (0)1509 611511 Fax: +44 (0)1509 610440 E-mail: salesuk@brush.eu Web: www.brush.eu
SM0000191P
BRUSH HMA b.v. PO Box 3007, 2980 DA Ridderkerk The Netherlands Tel: +31 180 445500 Fax: +31 180 445566 Email: salesnl@brush.eu Web: www.brush.eu
BRUSH SEM s.r.o. Edvarda Benese 39, 301 00 Plze Czech Republic Tel: +420 37 8210111 Fax: +420 37 8210214 Email: salescz@brush.eu Web: www.brush.eu
BRUSH TURBOGENERATORS Inc. 15110 Northwest Freeway, Suite 150, Houston, Texas 77040, USA Tel: +1 (281) 580 1314 Fax: +1 (281) 580 5801 Email: salesus@brush.eu Web: www.brush.eu
11/2008

Prismic A30

Uploaded by

Copyright:

Available Formats

Prismic A30

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Prismic A30

Uploaded by

Copyright:

Available Formats

PRISMIC A30

Exciter Exciter Field FSR

Set Voltage Datum

Communication Ports for Commissioning & Diagnostics

Fig 1. A30 Excitation Controller Scheme

You might also like