Introduction to Diodes Tutorial

Diodes are polarised, which means that they must be inserted into the PCB the correct way round.
This is because an electric current will only flow through them in one direction (like air will only flow
one way through a tyre valve).
Diodes have two connections, an anode and a cathode.
The cathode is always identified by a dot, ring or some other mark.

The pcb is often marked with a + sign for the cathode end.
Diodes come in all shapes and sizes.
They are often marked with a type number.
Detailed characteristics of a diode can be found by looking up the type number in a data book.
If you know how to measure resistance with a meter then test some diodes. A good one has low
resistance in one direction and high in the other.
There are specialised types of diode available such as the zener and light emitting diode (LED).

Barrier Tutorial
 Diode Characteristic Curves Tutorial

An electronic gate opens to let part of a signal through, and then shuts to reject the remainder.
It's like separating sheep from goats, using a real gate.
In the circuit, the cathodes of the diodes are more positive than the anodes.
They are reverse biased and non conducting.
The output of the circuit is isolated from the input.
When the negative gating pulse comes along, the cathodes become more negative than the
anodes.
The diodes are forward biased and conduct.
The output is connected to the input.
During the duration of the gating pulse, the input signal appears at the output. as shown by the
lowest waveform.

The cathode end of the diode is usually marked in some manner.

Diode Voltages Tutorial

To forward bias a diode, the anode must be more positive than the cathode or LESS NEGATIVE.
To reverse bias a diode, the anode must be less positive than the cathode or MORE NEGATIVE.
A conducting diode has about 0.6 volts across if silicon, 0.3 volts if germanium.

Forward Biased Junction Tutorial

 Half Wave Rectifier Tutorial

The voltage at point A does the opposite of that at point B.

When A is increasing in a positive direction, B is increasing in a negative direction.
It is rather like the two ends of a see-saw.
During the first half cycle of the waveform shown on the left, A is positive and B is negative.
The diode is forward biased and current flows around the circuit formed by the diode, the transformer
winding and the load.
Since the current through the load, and the voltage across the load are in the same proportions, then the
voltage across the load is as shown in the right hand diagram, during the first half cycle.
During the second half cycle, A and the anode are negative, B and the cathode are positive.
The diode is reverse biased and no current flows.
This is indicated by the horizontal line in the right hand diagram.
The diode only conducts on every other half cycle.
There is one pulse for every cycle in. i.e 50 pulses per second (in the UK)
The diode only conducts during half the cycle.
Hence, HALF-WAVE RECTIFICATION.
The rectified voltage is DC (it is always positive in value).
However, it is not a steady DC but PULSATING DC.
It needs to be smoothed before it becomes useful.
If the diode is reversed then the output voltage is negative.

Reservoir Capacitor Tutorial

The pulsating DC from the half wave rectifier needs to be smoothed to be useful.
This is done using a RESERVOIR capacitor.
It is not called this because of its construction but because of its application.
In the UK the weather is very variable. Sometimes we have periods of drought and sometimes
periods of prolonged rain. April is very showery and occasionally we have snow in Winter.
However, when I turn on the shower, the water always comes out at the same steady rate.
This is because it has been stored in a reservoir and is released as required.
It is the same with the reservoir capacitor.
The capacitor is charged up by the pulses.
It stores the pulses of voltage and the load is able to use this stored power as if it were a steady
supply available from a battery.

Looking at the first waveform, the red line indicates the voltage across the capacitor.
When the first pulse arrives the capacitor charges up to the peak voltage.
When this pulse has ended, the capacitor voltage starts to fall as the load takes energy from the
capacitor.
However, the voltage falls only slightly before the next pulse arrives to recharge the capacitor to
the peak voltage.
The result is a DC voltage with a superimposed 50 Hz (in the UK) ripple.
This is shown in the second waveform.
At low frequencies the capacitor is usually an electrolytic type, but at higher frequencies, where
smaller values are required, other types can be used.
 Semiconductor Materials Tutorial
The two most common materials used in the making of semiconductors are silicon and
germanium.
Sand on the beach is silicon and they say that germanium can be obtained from chimney soot.
So you can see that the raw materials are extremely common.
However they do have to be purified to an extraordinary degree.
When purified they have a crystalline construction like salt and sugar.
The atoms which make up the materials are rigidly locked together in a pattern (a LATTICE) in
which the electrons, in the atoms, are unable to move.
This means that pure silicon and germanium are good insulators.
After purification, precise amounts of impurities are added (the materials are DOPED).
These impurities fit into the lattice but have associated electrons which are free to move about and
produce a flow of electric current.
There is therefore a surplus of negative electrons and the material is called N-type semiconductor.
Other types of impurities can be added to pure silicon and germanium. These produce a shortage
of electrons in the lattice.
Therefore there are HOLES in the lattice.
Electrons can jump into these holes, producing a flow of holes.
It's like sitting in a row of chairs in the doctor's waiting room.
When someone gets up and goes into the surgery there is an empty chair (a hole).
People (electrons) move along nearer to the surgery and a hole travels in the opposite direction.
Since there is a shortage of negative electrons there is an overall positive charge and the material
is called P-type semiconductor.
The resistance of semiconductors is about half way between conductors and insulators.
Hence the name, semiconductors.
Semiconductors are used in semiconductor devices such as diodes, transistors, integrated circuits
etc.
Steering Diode Tutorial
If the AC supply fails then the equipment is automatically powered by the standby battery.
While the AC supply is present, D1 has +15 volts on its anode, and is forward biased.
Since there is 0.6 volts across the diode, there is +14.4 volts on its cathode.
This voltage powers the equipment.
D2 is reverse biased since its anode is less positive than its cathode.
D2 is non conducting and the battery is isolated.
If the supply fails then the +15 volts disappears, and D2 becomes forward biased and conducts, to power
the equipment.
The diodes STEER the voltages.

Varicap Diode Tutorial

When the junction diode is reverse biased, the insulating barrier widens.
The higher the reverse voltage the wider the barrier becomes.
The barrier forms the dielectric, of variable width, of a capacitor.
The N and P type cathode and anode are the two plates of the capacitor.
In the diagram, the diode and coil form a resonant circuit.
The capacitance of the diode, and thereby the resonant frequency, is varied by means of the
potentiometer controlling the reverse voltage across the varicap.
The capacitor prevents the coil shorting out the voltage across the potentiometer.

Zener Diode Tutorial

The Zener diode is operated in reverse bias mode (positive on its cathode).
It relies on the reverse breakdown voltage occurring at a specified value.
This value is printed on it.
It has two main applications.
1. as a reference source, where the voltage across it is compared with another voltage.
2. as a voltage regulator, smoothing out any voltages variations occurring in the supply voltage
across the load.
When being used a voltage regulator, if the voltage across the load tries to rise then the Zener
takes more current.
The increase in current through the resistor causes an increase in voltage dropped across the
resistor.
This increase in voltage across the resistor causes the voltage across the load to remain at its
correct value.
In a similar manner, if the voltage across the load tries to fall, then the Zener takes less current.
The current through the resistor and the voltage across the resistor both fall.
The voltage across the load remains at its correct value.
Diode Puzzle Tutorial
 Which lamps are alight?
Some may not be full brightness

An electronic gate opens to let part of a signal through, and then shuts to reject the remainder.
It's like separating sheep from goats, using a real gate.
In the circuit, the cathodes of the diodes are more positive than the anodes.
They are reverse biased and non conducting.
The output of the circuit is isolated from the input.
When the negative gating pulse comes along, the cathodes become more negative than the anodes.
The diodes are forward biased and conduct.
The output is connected to the input.
During the duration of the gating pulse, the input signal appears at the output. as shown by the lowest
waveform.

Diode Clippers and Limiters Tutorial

Clipping removes part of the positive or negative peaks of a signal or both.

Silicon diodes do not conduct until the applied voltage exceeds about 0.6 volts and only when the
anode is positive with respect to the cathode.
The circuit is like a potential divider with the diode part being high resistance for voltages below
0.6 volts and low resistance above.
Fig. 1 shows the waveform into the clipper.
Fig. 2 is the output of a positive clipper and fig. 3 the output of a negative clipper.
Fig. 4 has both peaks clipped and is often used as a LIMITER where the output must not exceed
1.2 volts.

Diode Protection Circuits Tutorial

Diagram A
This circuit consists of a relay coil being switched by a transistor.
When a coil is switched off, a large BACK EMF appears across the coil.
This back emf may be several thousand volts in value, enough to destroy the transistor.
The diode, which is normally reverse biased, is forward biased by the back emf, and conducts, its
low resistance short circuiting the back emf and protecting the transistor.
Diagram B
This circuit consists a meter movement with two germanium diodes across it.
Typical movements require only 100 mV for full scale deflection of the pointer.
If a voltage, exceeding about 0.3 volts, appears across the circuit then one of the diodes will
conduct and protect the movement from excessive voltage.

Forward and Reverse Biased Diodes

Tutorial
The left hand diagram shows reverse bias, with positive on the cathode and negative on the anode
(via the lamp). No current flows.
The other diagram shows forward bias, with positive on the anode and negative on the cathode,
and current flowing from cathode to anode.

Full Wave Rectifier Tutorial

 P-N Junction Tutorial

The P-N junction is made from a single crystal with the impurities diffused into it.
The N end has a surplus of negative electrons.
The P end has a surplus of holes.

Reverse Biased Junction Tutorial