Operating Instructions: Pt-Lm1U

R
LCD Projector Commercial Use
Operating Instructions
Model No.
PT-LM1U
POWER
INPUT
VIDEO
RGB
AUTO SETUP
MENU
ENTER
FREEZE
SHUTTER
STD VOLUME INDEX WINDOW D.ZOOM
PROJECTOR
Before operating this product, please read the instructions carefully and save this manual for future use.
TQBJ 0137-1
ENGLISH
Dear Panasonic Customer:

WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC CAUTION: To assure continued compliance, use only shielded interface cables when connecting to computers or peripheral devices. Any unauthorized changes or modifications to this equipment will void the users authority to operate. WARNING: B Not for use in a computer room as defined in the Standard for the Protection of Electronic Computer/Data Processing Equipment, ANSI/NFPA 75. B For permanently connected equipment, a readily accessible disconnect device shall be incorporated in the building installation wiring; B For pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily accessible. Declaration of Conformity Model Number: PT-LM1U Trade Name: Panasonic Responsible party: Matsushita Electric Corporation of America. Address: One Panasonic Way Secaucus New Jersey 07094 Telephone number: 1-800-528-8601 or 1-800-222-0741 Email: pbtsservice@panasonic.com This device complies with Part 15 of the FCC Rules, Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Model number: PT-LM1U Serial number:
IMPORTANT SAFETY NOTICE

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. Power Supply: This LCD Projector is designed to operate on 100 V 240 V, 50 Hz/60 Hz AC, house current only. CAUTION: The AC power cord which is supplied with the projector as an accessory can only be used for power supplies up to 125 V, 7 A. If you need to use higher voltages or currents than this, you will need to obtain a separate 250 V power cord. If you use the accessory cord in such situations, fire may result.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. CAUTION: This equipment is equipped with a three-pin grounding-type power plug. Do not remove the grounding pin on the power plug. This plug will only fit a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact an electrician. Do not defeat the purpose of the grounding plug.
Do not remove
2-ENGLISH
ENGLISH-3
Preparation
This instruction booklet provides all the necessary operating information that you might require. We hope it will help you to get the most out of your new product, and that you will be pleased with your Panasonic LCD projector. The serial number of your product may be found on its bottom. You should note it in the space provided below and retain this booklet in case service is required.
Contents
Preparation
IMPORTANT SAFETY NOTICE ...2 Precautions with regard to safety .........................................5 Accessories .................................9 Before use ..................................10 Location and function of each part...........................................12 SIGNAL MODE, Projecting sRGBcompatible pictures Adjusting the position...............38 POSITION, DOT CLOCK, CLOCK PHASE, ASPECT, RESIZING, FRAME LOCK Changing the display language..................................41 Option settings ..........................42 OSD, AUTO SIGNAL, AUTO KEYSTN, RGB/YPBPR, VGA60/525P, SXGA MODE, BACK COLOR, FRONT/REAR, DESK/CEILING, FAN CONTROL, LAMP POWER, LAMP RUNTIME, FUNC 1, CONTROL KEY, AUTO POW.OFF, POWER MEMORY Setting up the security function ...................................45 INPUT/AMEND PASSWD, TEXT DISPLAY/CHANGE
Precautions with regard to safety

If you notice smoke, strange smells or noise coming from the projector, disconnect the power cord plug from the wall outlet. B Do not continue to use the projector in such cases, otherwise fire or electric shocks could result. B Check that no more smoke is coming out, and then contact an Authorized Service Center for repairs. B Do not attempt to repair the projector yourself, as this can be dangerous. Do not install this projector in a place which is not strong enough to take the full weight of the projector. B If the installation location is not strong enough, it may fall down or tip over, and severe injury or damage could result. Installation work (such as ceiling suspension) should only be carried out by a qualified technician. B If installation is not carried out correctly, there is the danger that injury or electric shocks may occur. If foreign objects or water get inside the projector, or if the projector is dropped or the cabinet is broken, turn off the power and disconnect the power cord from the wall outlet. B Continued use of the projector in this condition may result in fire or electric shocks. B Contact an Authorized Service Center for repairs. Do not overload the wall outlet. B If the power supply is overloaded (for example, by using too many adapters), overheating may occur and fire may result. Do not remove the cover or modify it in any way. B High voltages can cause fire or electric shocks. B For any inspection, adjustment and repair work, please contact an Authorized Service Center. Clean the power cord plug regularly to prevent it from becoming covered in dust. B If dust builds up on the power cord plug, the resulting humidity can damage the insulation, which could result in fire. Pull the power cord out from the wall outlet and wipe it with a dry cloth. B If not using the projector for an extended period of time, pull the power cord plug out from the wall outlet.
Getting started
Setting-up...................................17 Projection methods, Projector position, Projection distances Connections...............................19 Connecting to computer, Connecting to video equipment Preparation for the remote control unit..............................21
Basic Operation
Turning on the power................22 Turning off the power................24
Care and maintenance

When the TEMP indicator and the LAMP indicator are illuminated...............................47 Cleaning and replacing the air filter ..............................49 Replacing the lamp unit ............50 Before calling for service..........53 Cleaning and maintenance .......55
Useful functions
Correcting keystone distortion and automatic positioning.....26 Turning off the picture and sound momentarily ............................27 Pausing a picture.......................27 Enlarging the picture.................28 Adjusting the volume ................28 Displaying two screens.............29
Others
Specifications ............................56 Appendix ....................................58 List of compatible signals, Connector pin wiring, Projection dimensions calculation methods Dimensions ................................60 Trademark acknowledgements ................60 NOTES IMPORTANTES CONCERNANT LA SCURIT...61 Prcautions de scurit..............62 Avant lutilisation...............................66 Remplacement du bloc de lampe...68
Adjustments and settings

On-screen menus ......................30 Menu screens, Menu operation guide, Returning a setting to the factory default Correcting keystone distortion .................................34 Adjusting the picture.................35 PICTURE MODE, CONTRAST, BRIGHT, COLOR, TINT, SHARPNESS, COLOR TEMP., White balance R/G/B, AI, TV-SYSTEM, STILL MODE,
4-ENGLISH
ENGLISH-5
Preparation
WARNING
Do not do anything that might damage the power cord or the power cord plug. B Do not damage the power cord, make any modifications to it, place it near any hot objects, bend it excessively, twist it, pull it, place heavy objects on top of it or wrap it into a bundle. B If the power cord is used while damaged, electric shocks, short-circuits or fire may result. B Ask an Authorized Service Center to carry out any repairs to the power cord that might be necessary. Do not handle the power cord plug with wet hands. B Failure to observe this may result in electric shocks. Insert the power cord plug securely into the wall outlet. B If the plug is not inserted correctly, electric shocks or overheating could result. B Do not use plugs which are damaged or wall outlets which are coming loose from the wall. Do not place the projector on top of surfaces which are unstable. B If the projector is placed on top of a surface which is sloped or unstable, it may fall down or tip over, and injury or damage could result. Do not place the projector into water or let it become wet. B Failure to observe this may result in fire or electric shocks. Do not place liquid containers on top of the projector. B If water spills onto the projector or gets inside it, fire or electric shocks could result. B If any water gets inside the projector, contact an Authorized Service Center. Do not insert any foreign objects into the projector. B Do not insert any metal objects or flammable objects into the projector or drop them onto the projector, as doing so can result in fire or electric shocks. Keep the batteries out of the reach of infants. B If the batteries are swallowed, death by suffocation may result. If you believe that the batteries may have been swallowed, seek medical advice immediately. Do not allow the + and - terminals of the batteries to come into contact with metallic objects such as necklaces or hairpins. B Failure to observe this may cause the batteries to leak, overheat, explode or catch fire. B Store the batteries in a plastic bag and keep them away from metallic objects. During a thunderstorm, do not touch the projector or the cable. B Electric shocks can result.
Do not use the projector in a bath or shower. B Fire or electric shocks can result. Do not look into the lens while the projector is being used. B Strong light is emitted from the projectors lens. If you look directly into this light, it can hurt and damage your eyes. B Be especially careful not to let young children look into the lens. In addition, disconnect the power cord when you are away from the projector. Do not place your hands or other objects close to the air outlet port. B Heated air comes out of the air outlet port. Do not place your hands or face, or objects which cannot withstand heat close to this port, otherwise burns or damage could result. Replacement of the lamp unit should only be carried out by a qualified technician. B The lamp unit has high internal pressure. If improperly handled, explosion might result. B The lamp unit can easily become damaged if struck against hard objects or dropped, and injury or malfunctions may result. When replacing the lamp, allow it to cool for at least one hour before handling it. B The lamp cover gets very hot, and contact with it can cause burns. Before replacing the lamp, be sure to disconnect the power cord from the wall outlet. B Electric shocks or explosions can result if this is not done.
Caution
Do not cover the air inlet or the air outlet. B Doing so may cause the projector to overheat, which can cause fire or damage to the projector. B Do not place the projector in narrow, badly ventilated places such as closets or bookshelves. B Do not place the projector on cloth or papers, as these materials could be drawn into the air inlet port. Do not set up the projector in humid or dusty places or in places where the projector may come into contact with smoke or steam. B Using the projector under such conditions may result in fire or electric shocks. When disconnecting the power cord, hold the plug, not the cord. B If the power cord itself is pulled, the cord will become damaged, and fire, short-circuits or serious electric shocks may result. Always disconnect all cables before moving the projector. B Moving the projector with cables still attached can damage the cables, which could cause fire or electric shocks to occur.
6-ENGLISH
ENGLISH-7
Preparation
Do not place any heavy objects on top of the projector. B Failure to observe this may cause the projector to become unbalanced and fall, which could result in damage or injury. Do not short-circuit, heat or disassemble the batteries or place them into water or fire. B Failure to observe this may cause the batteries to overheat, leak, explode or catch fire, and burns or other injury may result. When inserting the batteries, make sure the polarities (+ and -) are correct. B If the batteries are inserted incorrectly, they may explode or leak, and fire, injury or contamination of the battery compartment and surrounding area may result. Use only the specified batteries. B If incorrect batteries are used, they may explode or leak, and fire, injury or contamination of the battery compartment and surrounding area may result. Insulate the battery using tape or similar before disposal. B If the battery comes into contact with metallic objects or other batteries, it may catch fire or explode. Do not put your weight on this projector. B You could fall or the projector could break, and injury may result. B Be especially careful not to let young children climb onto the projector. If not using the projector for an extended period of time, disconnect the power cord plug from the wall outlet. B If dust builds up on the power cord plug, the resulting humidity may damage the insulation, which could result in fire. B This projector continues to draw approximately 5 W of power even when the power is turned off. Disconnect the power cord plug from the wall outlet as a safety precaution before carrying out any cleaning. B Electric shocks can result if this is not done. Ask an Authorized Service Center to clean inside the projector at least once a year. B If dust is left to build up inside the projector without being cleaned out, it can result in fire or problems with operation. B It is a good idea to clean the inside of the projector before the season for humid weather arrives. Ask your nearest Authorized Service Center to clean the projector when required. Please discuss with the Authorized Service Center regarding cleaning costs. We are constantly making efforts to preserve and maintain a clean environment. Please take non repairable units back to your dealer or a recycling company.
Accessories
Check that all of the accessories shown below have been included with your projector. Card remote control unit Lithium battery for (TNQE239 x1) remote control unit (CR2025 x1)
POWER INPUT VIDEO RGB
RGB signal cable [1.8 m (510), K1HA15DA0002 x1]
AUTO SETUP
MENU
ENTER
FREEZE
SHUTTER
Power cord (K2CG3DR00005 x 1)
Softcase (TPEP012 x 1)
PROJECTOR
8-ENGLISH
ENGLISH-9
Preparation
NOTICE: B This product has a High Intensity Discharge (HID) lamp that contains a small amount of mercury. It also contains lead in some components. Disposal of these materials may be regulated in your community due to environmental considerations. For disposal or recycling information please contact your local authorities, or the Electronics Industries Alliance: <http://www.eiae.org.>
Before use
Be sure to attach the lens cover before moving the projector. The projection lens is extremely susceptible to vibration and shocks. When moving the projector, use the accessory softcase. When placing the projector inside the softcase, position it so that the lens is facing upward. In order to get the best picture quality Draw curtains or blinds over any windows and turn off any fluorescent lights near the screen to prevent outside light or light from indoor lamps from shining onto the screen. Do not touch the surfaces of the lens with your bare hands. If the surface of the lens becomes dirty from fingerprints or anything else, this will be magnified and projected onto the screen. Moreover, when not using the projector, retract the lens and then cover it with the lens cover. Screen Do not apply any volatile substances which may cause discoloration to the screen, and do not let it become dirty or damaged. Lamp The lamp may need to be replaced earlier due to variables such as individual lamp characteristics, usage conditions and the installation environment, especially when the projector is subjected to continuous use for more than 10 hours or the power is frequently turned on and off. Liquid crystal panel The liquid crystal panel of the projector is built with very high precision technology to provide fine picture details. Occasionally, a few non-active pixels may appear on the screen as fixed points of blue, green or red. Please note that this does not affect the performance of your LCD.
Attach the lens cover so that the direction of the Panasonic logo becomes as shown in the figure above.
Cautions regarding setting-up

Avoid setting up in places which are subject to vibration or shocks. The internal parts can be damaged, which may cause malfunctions or accidents. Do not set up the projector near high-voltage power lines or near motors. The projector may be subject to electromagnetic interference. If installing the projector to the ceiling, ask a qualified technician to carry out all installation work. You will need to purchase the separate installation kit (Model No.ET-PKM1). Furthermore, all installation work should only be carried out by a qualified technician. If using this projector at high elevations (above 1 400 m), set the FAN CONTROL to HIGH. (Refer to page 43.) Failure to observe this may result in malfunctions.
10-ENGLISH
ENGLISH-11
Preparation
Caution when moving the projector
Notes on use
Location and function of each part

Projector <Top, right and front> # $ % & Projector <Back and bottom> # $ %
Preparation
&
IN PU T RG B ME NU
VI DE O
PO W ER
SH UT TE R
AU SE TO TU
ST D
FR EE ZE
IN WI DE ND X OW
D. ZO OM
EN TE R
, + * ) (
VO LU ME
PR OJ EC TO R
'
( '
# Connector panel (page 16) $ Air outlet port Do not cover this port. % Air inlet port Do not cover this port. & Lamp unit holder (page 50) ' Front adjustable legs (L/R) (page 23) ( Air inlet port, Air filter (page 49) Do not cover this port. NOTE: B During projection of an image, the cooling fan will operate, emitting a small noise as it operates. Turning the lamp on or off will cause this noise to increase a little. B By using the OPTION2 menu to set LAMP POWER to LOW, the operating sound of the fan can be reduced. (Refer to page 43.)
# Focus ring (page 23) $ Zoom ring (page 23) % Speaker & Projector control panel (Top) (page 14) ' Remote control unit holder Store the remote control unit as shown in the figure above. ( Leg adjuster buttons (L/R) (page 23) These buttons are used to unlock the front adjustable legs. Press to adjust the angle of tilt of the projector. ) Lens cover * Projection lens + Remote control signal receptor (page 21) , Air inlet port Do not cover this port.
WARNING
Do not place your hands or other objects close to the air outlet port. B Heated air comes out of the air outlet port. Do not place your hands or face, or objects which cannot withstand heat close to this port, otherwise burns or damage could result.
12-ENGLISH
ENGLISH-13
Projector control panel <Top> # ' ( $ )
Menu operation
<on connector panel:page 16>
% & Remote control unit ' ) +

AUTO SETUP MENU POWER INPUT
+,
(
RGB
VIDEO
* ,
ENTER
/
FREEZE SHUTTER STD VOLUME INDEX WINDOW D.ZOOM
. 0
PROJECTOR
# Power indicator (pages 22, 24 and 25) This indicator illuminates red when the projector is in standby mode, and it illuminates green when a picture starts to be projected. $ TEMP indicator (page 47) This indicator illuminates if an abnormally high temperature is detected inside the projector or around it. If the temperature rises above a certain level, the power supply will be turned off automatically and the indicator will flash. % LAMP indicator (page 48) This indicator illuminates when it is time to replace the lamp unit. It flashes if a circuit abnormality is detected. & RGB INPUT indicator This indicator illuminates when a signal is being input to the RGB IN connector. ' POWER button (pages 22 and 24) ( INPUT buttons (page 23) These buttons are used to switch the input signals from the connected equipment. ) AUTO SETUP button (pages 23 and 26) If this button is pressed while a picture is being projected, the projection settings will be adjusted automatically in accordance with the signal being input. In addition, the angle of tilt of the projector will be automatically detected and adjusted in order to correct any keystone distortion. * MENU button (pages 30 and 32) This button is used to display the MAIN MENU. When a menu screen is being displayed, this button can be used to return to a previous screen or to clear the screen. + Arrow (FGI and H) buttons (page 32) These buttons are used to select and adjust items in the on-screen menus. , ENTER button (page 32) This button is used to accept and to activate items selected in the on-screen menus. - FREEZE button (page 27) This button is used to momentarily freeze projection so that a still picture is displayed. . SHUTTER button (page 27) This button is used to momentarily turn off the picture and sound. / VOLUME +/- buttons (page 28) These buttons are used to adjust the volume of the sound output from the projectors built-in speaker. Refer to page 31 for details on how to adjust the volume using the buttons on the projector control panel. 0 STD (standard) button (page 33) This button is used to reset the projector adjustment values to the factory default settings. 1 INDEX WINDOW button (page 29) This button can be used to split the image projection area into a still picture and a moving picture. 2 D.ZOOM +/- buttons (page 28) These buttons are used to enlarge the projected image.
14-ENGLISH
ENGLISH-15
Preparation
Setting-up
Connector panel # $ Projection methods % & '
In way of installing projector, any one of the following four projection methods are used. Select whichever projection method matches the setting-up method. (The projection method can be set from the OPTION2 menu. Refer to page 43 for details.) BFront-desk projection BFront-ceiling projection
Menu items
Setting FRONT DESK
Menu items FRONT/REAR DESK/CEILING
Setting FRONT CEILING
FRONT/REAR DESK/CEILING
# Menu operation (on connector panel) (page 14) $ RGB IN connector (pages 19 and 20) This connector is used to input RGB signals and YPBPR signals. % S-VIDEO IN connector (pages 20 and 39) This connector is used to input signals from a S-VIDEO-compatible equipment such as a video deck. The connector is S1 signal compatible, and it automatically switches between 16:9 and 4:3 aspect ratios in accordance with the type of signal being input. & VIDEO IN jack (page 20) This jack is used to input video signals from a video equipment such as a video deck. ' AUDIO IN L-R jacks (pages 19 and 20) ( Power input socket (AC IN) (page 22) The accessory power cord is connected here. Do not use any power cord other than the accessory power cord. ) Security lock This can be used to connect a commercially-available theft-prevention cable (manufactured by Kensington). This security lock is compatible with the Microsaver Security System from Kensington.
BRear-desk projection (Using a translucent screen)
BRear-ceiling projection (Using a translucent screen)
Setting REAR DESK
Setting REAR CEILING
NOTE: B You will need to purchase the separate ceiling bracket (ET-PKM1) when using the ceiling installation method. B If you set up the projector vertically, it may cause to damage the projector. B It is recommended that you set up the projector in a place that is tilted at less than 30. Setting
up the projector in places that are tilted at more than 30 may cause malfunctions.
16-ENGLISH
ENGLISH-17
Getting started
Projector position
Top edge of screen SH <Units: mm (inch)> L: Projection distance SH: Image height SW:Image width H1: Distance from center of lens to bottom edge of projected image
Connections
Notes on connections
B Read the instruction manual for each peripheral device carefully before connecting it. B Turn off the power supply for all peripheral devices before making any connections. B If the cables necessary for connection are not included with the peripheral device or available as an option, you may need to prepare a proper cable for the device concerned. B If there is a lot of jitter in the video signal, the projected image may flicker. In such cases, it will be necessary to connect a TBC (time base corrector). B Refer to the list on page 58 for details on compatible signals which can be input to the projector. B Only one audio system circuit is available for the AUDIO IN L-R jacks, so if you change the audio input source, you will need to remove and insert the appropriate plugs.
Screen
L
H1 Bottom edge of screen
SW
Screen
Projection distances
Screen size (4:3) Diagonal length
0.84 m(33) 1.01 m(40) 1.27 m(50) 1.52 m(60) 1.77 m(70) 2.03 m(80) 2.28 m(90) 2.54 m(100) 3.81 m(150) 5.08 m(200) 6.35 m(250) 7.62 m(300)
Connecting to computer
Projection distance (L) Wide (LW)
1.2 m(311) 1.5 m(411) 1.9 m(62) 2.2 m(72) 2.5 m(82) 2.8 m(92) 3.1 m(102) 4.6 m(151) 6.2 m(204) 7.7 m(253) 9.3 m(306)
Height (SH)
0.50 m(17) 0.61 m(2) 0.76 m(26) 0.91 m(3) 1.07 m(36) 1.22 m(4) 1.37 m(46) 1.52 m(5) 2.29 m(76) 3.05 m(10) 3.81 m(126) 4.57 m(15)
Width (SW)
0.67 m(22) 0.81 m(28) 1.02 m(34) 1.22 m(4) 1.42 m(48) 1.63 m(54) 1.83 m(6) 2.03 m(68) 3.05 m(10) 4.06 m(134) 5.08 m(168) 6.10 m(20)
Telephoto (LT)
Height position (H1)
1.2 m(311) 0.07 m(2-3/4) 1.4 m(47) 0.09 m(3-17/32) 1.8 m(510) 0.11 m(4-5/16) 2.1 m(610) 0.13 m(5-3/32) 2.5 m(82) 0.15 m(5-7/8) 2.9 m(96) 0.17 m(6-11/16) 3.2 m(105) 0.20 m(7-27/32) 3.6 m(119) 0.22 m(8-21/32) 5.4 m(178) 0.33 m(12-31/32) 7.3 m(2311) 0.44 m(17-5/16) 9.1 m(2910) 0.54 m(21-1/4) 10.9 m(359) 0.65 m(25-9/16)
RGB signal cable (accessory)
NOTE: B The dimensions in the table above are approximate. B If you use the projection distance for the 16:9 screen, the 4:3 projection image overflows the screen at the top and bottom. B For details about projected image distances, refer to page 59.
Computer
18-ENGLISH
ENGLISH-19
Getting started
63.5 (2-1/2)
Preparation for the remote control unit

Connecting to video equipment
Insert the accessory lithium battery while making sure that the polarities are correct. # While pushing the battery holder tab to the right, pull out the battery holder. Back side Push the tab
Pull out $ Insert the battery into the battery holder so that the + side is facing upward. Match the + surface of the battery with the + marked side of the battery holder. % Insert the battery holder.
DVD player (with component video jack)
BNC/RCA adapter
DVD player
Video deck
NOTE: B If the signal cables are disconnected or if the power supply for the computer or video deck is turned off while D.ZOOM(digital zoom) or INDEX WINDOW is being used, these functions will be cancelled.
NOTE: B Do not drop the remote control unit. B Keep the remote control unit away from liquids. B Remove the battery if not using the remote control unit for long periods. B Use only CR2025 batteries as replacement batteries. B If the remote control unit is held so that it is facing directly in front of the remote control signal receptor, the operating range is within approximately 7 m (23) from the surfaces of the receptor. Furthermore, the remote control unit can be operated from an angle of 30 to the left or right and 15 above or below the receptors. B If there are any obstacles in between the remote control unit and the receptor, the remote control unit may not operate correctly. B If strong light is allowed to shine onto the remote control signal receptor, correct projector operation may not be possible. Place the projector as far away from light sources as possible. B If facing the remote control unit toward the screen to operate the projector, the operating range of the remote control unit will be limited by the amount of light reflection loss caused by the characteristics of the screen used.
20-ENGLISH
ENGLISH-21
Getting started
D-sub15-pin (male) - BNCx5 (male) adapter cable Red (connect to PR signal connector) Blue (connect to PB signal connector) Green (connect to Y signal connector)
Turning on the power

Before turning on the power 1, Ensure that all peripheral devices are connected properly. 2, Remove the lens cover.
POWER
# Power cord
the input select button to select the & Press input signal.
Input select buttons Changing signals
VIDEO
RGB
INPUT
$
RGB
RGB
VIDEO S-VIDEO
VIDEO RGB S-VIDEO

Basic Operation
VIDEO
AUTO SETUP
&
MENU ENTER
(
SHUTTER
FREEZE
) *
BA picture will be projected in accordance with the selected input signal. BWhen a YPBPR signal is being input, YPBPR will be displayed instead of RGB. Follow the procedure below when you set the projector up first, and when you change the setup place.
the angle ' Adjusting BWhile pressing the adjuster buttons,

Lens cover
PROJECTOR
'
Power indicator
adjust the forward/back angle of tilt of the projector. Adjust so that the projector is as vertical to the screen as possible.
the accessory power cord to the AC IN # Connect socket.

BThe power indicator on the projector will illuminate red.
the AUTO SETUP button to initiate ( Press automatic positioning.

BThe tilt of the projector and the input signal will be detected and keystone distortion and the position of the image will be corrected. (Refer to page 26 for details.)
$ BThe power indicator on the projector will flash green. After a short
period, the indicator will illuminate green, and a picture will be projected.
Press the POWER button.
AUTO SETUP
on the power of all connected devices. % Turn BStart the play function of a device such as a DVD player.
NOTE: B If the power cord was disconnected during projection when the projector was used the last time, projection will start after the power cord is connected (when POWER MEMORY in the OPTION2 menu is set to ON). Refer to page 44 for details. B A tinkling sound may be heard when the lamp unit is turned on, but this is not a sign of a malfunction.
the size ) Adjusting BTurn the zoom ring to adjust the size of the projected image. the focus * Adjusting BTurn the focus ring to adjust the focus of the projected image.
ENGLISH-23
22-ENGLISH
Turning off the power

Power indicator
#
POWER INPUT VIDEO RGB
AUTO SETUP
MENU
ENTER
FREEZE
SHUTTER
PROJECTOR
You can disconnect the power cord during projection or immediately after use and move the projector. The cooling fan will operate by the internal power supply to cool down the lamp. B When this function is used, it may take more time for the lamp to turn back on again compared to when the lamp cools down with the power cord connected. B Do not put the projector in a bag while the cooling fan is operating.
% Power cord
the POWER button. # Press BPOWER OFF is displayed on the
screen.
CAUTION
If not using the projector for an extended period of time, disconnect the power cord plug from the wall outlet. B If dust builds up on the power cord plug, the resulting humidity may damage the insulation, which could result in fire. B This projector continues to draw approximately 5 W of power even when the power is turned off. Power indicator Power indicator status Red
Illuminated
POWER OFF OK CANCEL
the I or H button to select OK, and $ Press then press the ENTER button.
BThe lamp unit will switch off and the picture will stop being projected. (The power indicator on the projector will illuminate orange while the cooling fan is still operating.)
the power cord after the power % Disconnect indicator on the projector illuminates red.
NOTE: B You can also turn off the power by pressing the POWER button twice or by holding it down for at least 0.5 seconds. B When the projector is in standby mode (the power indicator on the projector is illuminated red), the projector continues to draw approximately 5 W of power even when the cooling fan has stopped.
Green
Flashing
Illuminated Illuminated
Orange Flashing
Projector status The projector is in standby mode and image projection is possible by pressing the POWER button. The projector is preparing for projection after the power is turned on while the power indicator is illuminated red. (After a short period, a picture will be projected.) A picture is being projected. The lamp is cooling down after the power is turned off. (The cooling fan is operating.) The projector is preparing for projection after the power is turned on while the power indicator is illuminated orange. (After a short period, a picture will be projected.)
24-ENGLISH
ENGLISH-25
Basic Operation
Direct power off function
Correcting keystone distortion and automatic positioning (AUTO SETUP)

This projector detects its degree of tilt and the input signal. Keystone distortion and the position of the image can then be corrected automatically in accordance with the input signal.
POWER INPUT
Turning off the picture and sound momentarily (SHUTTER)

The SHUTTER function can be used to momentarily turn off the picture and sound from the projector when the projector is not being used for short periods of time, such as during breaks in meetings or when carrying out preparation. The projector uses less power in SHUTTER mode than it does in normal projection mode.
POWER INPUT
Press the AUTO SETUP button. (When the projected image has caused keystone distortion)
RGB
VIDEO
AUTO SETUP
MENU
Screen
AUTO SETUP
VIDEO
RGB
ENTER
MENU
FREEZE
SHUTTER
Projected image B Automatic positioning will be carried out.
Press the SHUTTER button. B The picture and sound will be turned off. B Press any button on either the projector or remote control unit to return to normal operating mode. NOTE: B SHUTTER on the MAIN MENU is the same function.
ENTER
FREEZE
SHUTTER
PROJECTOR
Projector control panel
PROJECTOR
Pausing a picture (FREEZE)

POWER INPUT
Press the FREEZE button.

RGB
VIDEO
NOTE: B When RGB signals are being input, DOT CLOCK, and CLOCK PHASE will be adjusted automatically in addition to keystone distortion and the position of the image being corrected (except when the dot clock frequency is 100 MHz or higher). Refer to page 38 for details. B If the edges of the projected image are indistinct, or if a dark picture is being projected, the automatic setup processing may stop automatically before it is complete. If this happens, project a different picture and then press the AUTO SETUP button again. B Set AUTO KEYSTN in the OPTION1 menu to OFF to prevent any deterioration of the picture as a result of keystone correction. (Refer to page 42.)
AUTO SETUP
MENU
Still picture
ENTER
FREEZE
SHUTTER
B The picture being projected will be paused. B Press the FREEZE button again to cancel the still picture.
PROJECTOR
26-ENGLISH
ENGLISH-27
Useful functions
Enlarging the picture (D.ZOOM)

POWER INPUT
Displaying two screens (INDEX WINDOW)

This function lets you store a picture which is being projected into memory, so that you can display a still picture and a moving picture on the screen.
AUTO SETUP MENU
Press the D.ZOOM +/- button.

RGB
VIDEO
AUTO SETUP
MENU
ENTER ENTER
FREEZE FREEZE SHUTTER
SHUTTER
B The picture will then be enlarged to 1.5 times the normal size.
Press the INDEX WINDOW button. B The aspect ratio of the screen changes and the image is vertically elongated in comparison to a normal image.
Still picture
Moving picture
PROJECTOR PROJECTOR
The remote control unit functions during INDEX WINDOW Press the F or G button to select a screen size. It can switch to three stages.
The remote control unit functions during D.ZOOM (digital zoom) Press the F,G,IandHbuttons to move the enlarged area which you want to project. Press the D.ZOOM +/- buttons to change the enlargement ratio. Press the MENU button to return to the normal screen. NOTE: B The enlargement ratio can be changed within the range of x1 to x2, in steps of 0.1. When RGB signals are being input, the enlargement ratio can be changed within the range of x1 to x3, except when the FRAME LOCK is set to ON. B If the type of signal being input changes while the digital zoom function is being used, the digital zoom function will be cancelled.
Still picture
Moving picture
Still picture
Moving picture
Still Moving picture picture
Press the I or H button to switch between the still picture screen and moving picture screen.
Still picture
Moving picture
Moving picture
Still picture
Adjusting the volume (VOLUME)

Press the VOLUME +/- button. B Press the + button to raise the volume. B Press the - button to lower the volume. NOTE: B You can also select VOLUME from the MAIN MENU to adjust the volume.
Press the ENTER button to capture the present moving picture in a still window. Press the MENU button to return to the previous screen. NOTE: B When the screen size is changed, the pictures aspect ratio will also change. Make sure that you fully understand the notes on ASPECT on page 40 before using the INDEX WINDOW function. B INDEX WINDOW on the MAIN MENU is the same function.
PROJECTOR
28-ENGLISH
ENGLISH-29
Useful functions
On-screen menus
Menu screens
The various settings and adjustments for this projector can be carried out by selecting the operations from on-screen menus. The general arrangement of these menus is shown below. MAIN MENU PICTURE menu (page 35) When an RGB signal is being input POSITION menu (page 38) When an RGB/YPBPR signal is being input OPTION1 menu (page 42)
MENU KEYSTONE PICTURE POSITION INDEX WINDOW SHUTTER VOLUME LANGUAGE OPTION1 OPTION2 SECURITY SELECT ENTER
EXIT
PICTURE PICTURE MODE DYNAMIC CONTRAST 32 BRIGHT 32 SHARPNESS 0 COLOR TEMP. STANDARD W-BAL R 32 W-BAL G 32 W-BAL B 32 AI ON SIGNAL MODE XGA STANDARD SELECT ADJ RETRN
When a YPBPR signal is being input
POSITION POSITION DOT CLOCK 32 CLOCK PHASE 16 ASPECT 4:3 RESIZING ON FRAME LOCK OFF STANDARD SELECT ENTER RETRN
When an S-VIDEO/VIDEO signal is being input
OPTION1 OSD ON AUTO SIGNAL ON AUTO KEYSTN ON AUTO RGB/YPB PR VGA60/525P VGA60 SXGA MODE SXGA SELECT ADJ RETRN
OPTION2 menu (page 42)
INDEX WINDOW function (page 29) SHUTTER function (page 27) VOLUME adjustment Press the ENTER button, and then press the I or H button to adjust the volume. LANGUAGE menu (page 41)
KEYSTONE correction (page 34)
SECURITY menu (page 45)
KEYSTONE
0
B Keystone distortion of the on-screen display will not be corrected.
PICTURE PICTURE MODE STANDARD CONTRAST 32 BRIGHT 32 COLOR 32 TINT 32 SHARPNESS 2 COLOR TEMP. STANDARD AI ON TV-SYSTEM AUTO STILL MODE OFF STANDARD SELECT ADJ RETRN
SECURITY INPUT PASSWD OFF AMEND PASSWD TEXT DISPLAY ON TEXT CHANGE SELECT ADJ RETRN
LANGUAGE ENGLISH DEUTSCH FRANAIS ESPAOL ITALIANO
ENGLISH
SELECT
ENTER
RETRN
30-ENGLISH
ENGLISH-31
B Press the MENU button to display the MAIN MENU. Refer to page 32 for details on how to operate the on-screen menus.
PICTURE PICTURE MODE STANDARD CONTRAST 32 BRIGHT 32 COLOR 32 TINT 32 SHARPNESS 2 COLOR TEMP. STANDARD AI ON SIGNAL MODE 525P STANDARD SELECT ADJ RETRN
POSITION POSITION ASPECT 4:3 RESIZING ON STANDARD SELECT ENTER RETRN
OPTION2 BACK COLOR BLUE FRONT/REAR FRONT DESK/CEILING DESK FAN CONTROL STANDARD LAMP POWER HIGH LAMP RUNTIME 100H FUNC 1 INDEX CONTROL KEY ON AUTO POW.OFF DISABLE POWER MEMORY ON SELECT ADJ RETRN
Menu operation guide

# Press the MENU button. The MAIN MENU MENU will be displayed. KEYSTONE
POWER
INPUT
VIDEO
RGB
AUTO SETUP
MENU
ENTER
FREEZE
SHUTTER
PICTURE POSITION INDEX WINDOW SHUTTER VOLUME LANGUAGE OPTION1 OPTION2 SECURITY SELECT ENTER
& Press the F or G button to select an item, and then press the I or H button to change or adjust the setting. An individual adjustment screen such as the one shown below will be displayed for bar-scale items.
Unavailable on-screen menu items

This projector has unadjustable items and unusable functions depending on the signal being input. When an item cannot be adjusted or a function cannot be used, the corresponding on-screen menu display does not appear, and the item or function will not work even if the ENTER button is pressed.
BRIGHT
32
The bar scale will turn green when any adjustment changes the setting from the factory set value.
EXIT
Returning a setting to the factory default

If you press the STD (standard) button on the remote control unit, you can return settings to the factory default settings. However, the operation of this function varies depending on which screen is being displayed. B When a menu screen is being displayed B When an individual adjustment screen is being displayed
PROJECTOR
Menu operation (on connector panel)
$ Press the F or G button to select an item. Selected item will MENU be displayed in KEYSTONE blue. PICTURE
EXIT
% Press the ENTER button to accept the selection. PICTURE The selected P I C T U R E MODE STANDARD menu screen or C O N T R A S T 32 adjustment BRIGHT 32 screen will then C O L O R 32 be displayed. TINT 32 (Example: SHARPNESS 2 PICTURE COLOR TEMP. STANDARD menu) AI ON NOTE: B Press the MENU button to return to the previous screen.
TV-SYSTEM STILL MODE STANDARD SELECT ADJ
AUTO OFF RETRN
All items displayed will be returned to their factory default settings, STD will be displayed in the topright screen and the bar scale will appear white. NOTE: B You can also select STANDARD from the menu screen and then press the ENTER button.
NOTE: B Triangle symbols above and below the bar scale indicate the factory default setting. Items which do not have these triangle symbols cannot be returned to the factory default setting. Indicates the standard factory default setting
Indicates the current adjustment value B The positions of triangle symbols vary depending on the type of signal being input.
32-ENGLISH
ENGLISH-33
POSITION INDEX WINDOW SHUTTER VOLUME LANGUAGE OPTION1 OPTION2 SECURITY SELECT ENTER
PICTURE STD PICTURE MODE STANDARD CONTRAST 32 BRIGHT 32 COLOR 32 TINT 32 SHARPNESS 2 COLOR TEMP. STANDARD AI ON TV-SYSTEM AUTO STILL MODE OFF STANDARD SELECT ENTER RETRN
BRIGHT
32
Only the item displayed will be returned to the factory default setting, and the bar scale will appear white.
Correcting keystone distortion

Keystone distortion is corrected automatically when the projectors automatic setup function is used, but this correction will not apply if the screen itself is tilted. In such cases, you can correct the keystone distortion manually with the following procedure. Vertical keystone distortion correction only.
Adjusting the picture

Press the F or G button on the projector or remote control unit to select an item, and then press the I or H button to change the setting. For items with bar scales, press the ENTER button or the I or H button to display the adjustment screen, and then press the I or H button to make the adjustment. When an S-VIDEO/VIDEO signal is being input
KEYSTONE
Vertical keystone distortion correction Operation
Press the H button.
Press the I button.
When an RGB signal is being input
When an YPBPR signal is being input
PICTURE PICTURE MODE STANDARD CONTRAST 32 BRIGHT 32 COLOR 32 TINT 32 SHARPNESS 2 COLOR TEMP. STANDARD AI ON SIGNAL MODE 525P STANDARD SELECT ADJ RETRN
CONTRAST
This adjusts the contrast of the picture. (Adjust the BRIGHT setting first if required before adjusting the CONTRAST setting.) The picture is bright: I button The picture is dark: H button
34-ENGLISH
ENGLISH-35
NOTE: B If you press the AUTO SETUP button after correcting the keystone distortion manually, the automatic keystone correction function will operate and the corrected picture will return to its previous incorrect condition. To prevent this from happening, you can set AUTO KEYSTN in the OPTION1 menu to OFF. (Refer to page 42.) B Vertical keystone distortion can be corrected to 30 of the angle of tilt. However, the greater the correction amount, the more the picture quality will deteriorate, and the harder it will become to achieve a good level of focus. To obtain the best picture quality, set up the projector and screen in such a way that the amount of keystone correction required is as minimal as possible. B The picture size will also change when correction of keystone distortion is carried out.
PICTURE PICTURE MODE DYNAMIC CONTRAST 32 BRIGHT 32 SHARPNESS 0 COLOR TEMP. STANDARD W-BAL R 32 W-BAL G 32 W-BAL B 32 AI ON SIGNAL MODE XGA STANDARD SELECT ADJ RETRN
PICTURE PICTURE MODE STANDARD CONTRAST 32 BRIGHT 32 COLOR 32 TINT 32 SHARPNESS 2 COLOR TEMP. STANDARD AI ON TV-SYSTEM AUTO STILL MODE OFF STANDARD SELECT ADJ RETRN
PICTURE MODE
PICTURE MODE NATURAL
[
STANDARD
[
DYNAMIC
Select the picture mode that best matches the image source and room conditions. The mode best used in dark rooms is NATURAL. For rooms having regular lighting conditions in use, select STANDARD. For exceptionally bright rooms, use DYNAMIC.
BRIGHT
This adjusts the darker areas (black areas) in the picture. Black areas are too light: I button Dark areas are too solid: H button
AI
AI ON
[
STILL MODE
STILL MODE OFF
[
OFF
ON The lamp is controlled according to the input signals to project images with the best quality. OFF AI is disabled. NOTE: B AI is disabled when LAMP POWER is set to LOW. (Refer to page 43.)
COLOR
(S-VIDEO/VIDEO/YPBPR only) The color is too deep: I button The color is too pale: H button
ON To reduce flickering of still images (vertical flicker), set STILL MODE to ON.
NOTE: B Do not set STILL MODE to ON when playing back moving images.
TINT
(NTSC/NTSC 4.43/YPBPR only) This adjusts the flesh tones in the picture. The flesh tones are greenish: I button The flesh tones are reddish: H button
SIGNAL MODE
(RGB/YPBPR only) This displays the type of signal which is currently being projected. Refer to the table on page 58 for details on each type of signal.
SHARPNESS
To soften the picture details: I button To sharpen the picture details: H button
TV-SYSTEM
(S-VIDEO/VIDEO only) TV-SYSTEM AUTO
[
COLOR TEMP.
COLOR TEMP. STANDARD
[
NTSC
[
NTSC4.43
[
HIGH
[
PAL
[
LOW
This is used to adjust the white areas of the picture if they appear bluish or reddish.
PAL-M
[
PAL-N
[
SECAM
This should normally be set to AUTO. If the signal is of such poor quality that the correct format cannot be automatically distinguished, change the setting manually to the required TV system. NOTE: B When set to AUTO, the projector automatically distinguishes between NTSC/NTSC 4.43/PAL/PAL60/ PAL-M/PAL-N/SECAM signals.
White balance R/G/B (W-BAL R/G/B)

(RGB only) This is used to adjust the white areas of the picture if they appear colorised. To make the selected color lighter : I button To make the selected color stronger : H button
sRGB is an international color reproduction standard (IEC61966-2-1) established by the International Electrotechnical Commission (IEC). If you would like the colors in sRGBcompatible pictures to be reproduced more faithfully, make the following settings. # Press the F or G button to select PICTURE MODE, and then press the I or H button to select NATURAL. $ Press the STD (standard) button on the remote control unit. % Press the F or G button to select COLOR TEMP., and then press the I or H button to select STANDARD. NOTE: B sRGB is only enabled when RGB signals are being input (when LAMP POWER is set to HIGH).
36-ENGLISH
ENGLISH-37
Projecting sRGB-compatible pictures
Adjusting the position

When an RGB signal is being input, press the AUTO SETUP button first to initiate automatic positioning. If the optimum setting is not obtained when AUTO SETUP is carried out, adjust by the following procedure. Press the F or G button on the projector or remote control unit to select an item, and then press the I or H button to change the setting. For items with bar scales, press the ENTER button or the I or H button to display the adjustment screen, and then press the I or H button to make the adjustment. When an RGB/YPBPR signal is being input
POSITION
Moves the picture position. Press the ENTER button to display the POSITION screen. Press the I or H button to move the picture horizontally. Press the F or G button to move the picture vertically.
ASPECT
(S-VIDEO/VIDEO/525i, 525p, 625i and 625p YPBPR signals only)
ASPECT
AUTO
[
4:3
[
S4:3 The size of the input signal is compressed to 75% and projected. (This is useful for projecting a picture with a 4:3 aspect ratio onto a 16:9 screen.)
16:9
[
POSITION
H V
64 32
S4:3
AUTO (S-VIDEO only) When an S1 video signal is being input, the aspect ratio is changed automatically to project a 16:9 picture. 4:3 The input signal is projected without change. 16:9 The picture is compressed to a ratio of 16:9 and projected.
DOT CLOCK
(RGB only) Periodic striped pattern interference (noise) may occur when a striped pattern such as the one below is projected. If this happens, press the I or H button to adjust so that any such noise is minimised.
When a 4:3 signal is being input.

[
CLOCK PHASE
[RGB/YPBPR (except for 525i, 525p, 625i and 625p YPBPR signals) only] Adjust the DOT CLOCK setting first before carrying out this adjustment. Press the I or H button to adjust so that the noise level is least noticeable. NOTE: B If signals with a dot clock frequency of 100 MHz or higher are being input, interference may not be completely eliminated when the DOT CLOCK and CLOCK PHASE adjustments are carried out. When using the 16:9 screen When a horizontally squeezed signal is being input.
[
POSITION POSITION ASPECT 4:3 RESIZING ON STANDARD SELECT ENTER RETRN
S1 video signals B S1 video signals are a type of video signal with an aspect ratio of 16:9 which include a detector signal. This detector signal is output by some sources such as wide-vision video decks. B When ASPECT is set to AUTO, the projector recognizes the detector signal and automatically switches the aspect ratio to 16:9.
38-ENGLISH
ENGLISH-39
POSITION POSITION DOT CLOCK 32 CLOCK PHASE 16 ASPECT 4:3 RESIZING ON FRAME LOCK OFF STANDARD SELECT ENTER RETRN
Changing the display language

NOTE: B If a selected mode does not match the aspect ratio of the input signal, it may affect the quality of viewing of the original picture. Keep this in mind when selecting the aspect ratio. B If using this projector in places such as cafes or hotels to display programs for a commercial purpose or for public presentation, note that if the aspect ratio (16:9) selection function is used to change the aspect ratio of the screen picture, you may be infringing the rights of the original copyright owner for that program under copyright protection laws. B If a normal (4:3) picture which was not originally intended for wide-screen viewing is projected onto a wide screen, distortion may occur around the edges of the picture, or part of the picture may not be visible. Such programs should be viewed in 4:3 mode to give proper consideration to the aims and intentions of the original programs creator.
RESIZING
This should normally be set to ON. (This setting is only for signals which have lower resolutions than the LCD panels. Refer to page 58 for details.) ON The pixel resolution of the input signal is converted to the same resolution as the LCD panels before being projected. For signals with lower resolutions, gaps in the pixels are automatically interpolated into the picture before it is projected. This may sometimes cause problems with the quality of the picture. OFF The input signal is projected at its original resolution, with no pixel conversion. The projected picture will be smaller than normal, so adjust the zoom setting or move the projector forwards or backwards to adjust the picture size if necessary. If set to OFF, some features, such as D.ZOOM (digital zoom), KEYSTONE or INDEX WINDOW will not function.
Press the F or G button on the projector or remote control unit to select a language, then press the ENTER button to accept the setting.
LANGUAGE ENGLISH DEUTSCH FRANAIS ESPAOL ITALIANO
ENGLISH
Indicates the language which is currently set.
SELECT
ENTER
RETRN
FRAME LOCK
If the pictures condition is bad while a RGB moving picture is projected, set FRAME LOCK to ON. Refer to page 58 for compatible RGB signals.
40-ENGLISH
ENGLISH-41
Option settings
Press the F or G button on the projector or remote control unit to select an item, then press the I or H button to change the setting.
AUTO SIGNAL
This should normally be set to ON. ON AUTO SETUP will be carried out automatically when the input signal is changed. OFF AUTO SETUP will not function when the input signal is changed.
VGA60/525P
VGA60/525P 525P
[
DESK/CEILING
DESK/CEILING DESK
[
VGA60
When a VGA60 or 525p RGB signal is being input, select the signal in accordance with the input signal.
OPTION1 OSD ON AUTO SIGNAL ON AUTO KEYSTN ON AUTO RGB/YPB PR VGA60/525P VGA60 SXGA MODE SXGA SELECT ADJ RETRN
SXGA MODE
SXGA MODE SXGA
[
AUTO KEYSTN
This should normally be set to ON. ON During AUTO SETUP, the angle of tilt of the projector is detected and keystone distortion is corrected automatically. OFF Use this setting when you do not want automatic keystone correction to be carried out during AUTO SETUP, such as when the screen itself is at an angle.
BACK COLOR
BLUE
[
LAMP POWER
LAMP POWER HIGH
[
RGB/YPBPR
RGB/YPB PR AUTO RGB
[ [
OSD
ON The signal name is displayed in the top-right corner of the screen when the input signal is changed. OFF Use this setting when you do not want the signal name to be displayed. NOTE: B The setting for TV-SYSTEM will also be displayed when an S-VIDEO/VIDEO signal is being input.
BLACK This sets the color which is projected onto the screen when no signal is being input to the projector.
YPB PR
This should normally be set to AUTO. RGB or YPBPR is selected automatically depending on the synchronising signal status. When HDTV, 525p, 525i, 625p, 625i, 750p, and some VGA480 signals are being input, select RGB or YPBPR in accordance with the input signal.
FRONT/REAR
FRONT/REAR FRONT
[
REAR This setting should be changed in accordance with the projector setting-up method. (Refer to page 17.) FRONT When the projector is placed in front of a screen. REAR When using a translucent screen.
LOW This setting changes the lamp brightness. When set to LOW, the luminance of the lamp is reduced, but the projector uses less power, and the operating noise is also reduced. This can help to extend the lamps operating life. If using the projector in small rooms where high luminance is not required, it is recommended that you set the LAMP POWER to LOW.
42-ENGLISH
ENGLISH-43
OPTION2 BACK COLOR BLUE FRONT/REAR FRONT DESK/CEILING DESK FAN CONTROL STANDARD LAMP POWER HIGH LAMP RUNTIME 100H FUNC 1 INDEX CONTROL KEY ON AUTO POW.OFF DISABLE POWER MEMORY ON SELECT ADJ RETRN
SXGA+ This setting is only for an SXGA signal. SXGA Select this item normally. SXGA+ When the edges of the projected image are not visible, select this item.
CEILING This setting should be changed in accordance with the projector setting-up method. (Refer to page 17.) DESK When the projector is placed on a desk or similar. CEILING When the projector is suspended from a ceiling using the ceiling bracket (sold separately).
FAN CONTROL
FAN CONTROL STANDARD
[
BACK COLOR
HIGH Set FAN CONTROL to HIGH, when using this projector at high elevations (above 1 400 m) only.
Setting up the security function

LAMP RUNTIME
This setting displays the usage time for the lamp unit which is currently being used. When replacing the lamp unit, follow the instructions on page 51, and reset LAMP RUNTIME to 0. NOTE: B The lamps operating life varies depending on the usage conditions (such as the LAMP POWER setting and the number of times the power is turned on and off).
CONTROL KEY
CONTROL KEY ON
[
This projector is equipped with a security function. A password input screen can be displayed, or a company URL can be set up and displayed at the bottom of the projected image. Press the F or G button on the projector or remote control unit to select SECURITY, then press the ENTER button.
OFF To disable the buttons on the projector, set CONTROL KEY to OFF. A confirmation screen will then be displayed. Select OK by using I or H button. To use the buttons on the projector, set to ON by using the remote control unit.
INPUT PASSWD
The password input screen can be displayed when the power is turned on. All of the controls other than the POWER button are disabled unless the password is entered correctly. ON INPUT PASSWD is enabled. OFF INPUT PASSWD is disabled. The password input screen will not be displayed when the power is turned on.
AUTO POW.OFF
If no signal is input to the projector for the duration of the period you set, the projector will return to standby mode. The period can be set from 15 minutes to 60 minutes in 5 minute intervals. If you don't use this feature, set it to DISABLE. This feature will not function when using the FREEZE function.
FUNC 1
FUNC1 INDEX
[
EXIT
KEYSTONE This assigns a function to the FUNC1 button of the ET-RM200 wireless remote control unit (sold separately). INDEX Functions in the same way as the INDEX WINDOW button on the accessory card remote control unit. (page 29) KEYSTONE Functions in the same way as when KEYSTONE is selected from the MAIN MENU. (page 34)
AMEND PASSWD
PASSWORD OK RETURN NEW
(When you use the SECURITY function for the first time) Press the F, H, G, I, F, H, G and I buttons in order, then press the ENTER button. (When a password change has been made before) Type in the changed password, then press the ENTER button.
POWER MEMORY
POWER MEMORY ON
[
AMEND PASSWD CONFIRM OK RETURN
OFF
This sets the projectors start up status for when the power cord is connected. ON The projector will start from the same status as when the power cord was disconnected. If the power cord was disconnected during projection when the projector was used the last time, projection will start after the power cord is connected. OFF The projector will be in standby mode.
SECURITY INPUT PASSWD OFF AMEND PASSWD TEXT DISPLAY ON TEXT CHANGE SELECT ADJ RETRN
# Set a password by pressing the F,G,I, and H buttons. (A maximum of 8 buttons can be set.) $ Press the ENTER button. % Enter the password again for confirmation. & Press the ENTER button. Password change will be completed.
44-ENGLISH
ENGLISH-45
Passwords can be changed. Press the ENTER button to display the AMEND PASSWD screen.
NOTE: B The entered password will appear as . It will not be displayed on the screen. B If you enter the wrong password, the letters PASSWORD and NEW will become red. Enter the correct password again.
TEXT DISPLAY
The setup letters can be displayed at the bottom of the projected image while an image is projected. ON TEXT DISPLAY is enabled. OFF TEXT DISPLAY is disabled.
When the TEMP indicator and the LAMP indicator are illuminated
There are two indicators on the control panel of the projector which give information about the operating condition of the projector. These indicators illuminate or flash to warn you about problems that have occurred inside the projector, so if you notice that one of the indicators is on, turn off the power and check the table below for the cause of the problem. TEMP indicator
TEXT CHANGE
The setup letters which will be displayed when TEXT DISPLAY is set to ON can be changed. Press the ENTER button to display the TEXT CHANGE screen. LAMP indicator
TEXT CHANGE ABCDEFGHIJKLMNO PQRSTUVWXYZ0123 456789 @.:;/+BS OK Cancel
TEMP indicator Indicator display Illuminated (red) (Lamp unit on) The surrounding temperature or the temperature inside the projector has Problem become unusually high. Flashing (red) (Lamp unit on) The temperature inside the projector has become dangerously high, or the temperature has suddenly changed. Flashing (red) (Lamp unit off) The surrounding temperature or the temperature inside the projector has become dangerously high, causing the lamp unit to automatically shut off.
B The ventilation holes may be covered. Possible B The ambient temperature in the place of use may be too high. cause B The air filter may be blocked. B Uncover the ventilation holes. B Set up the projector in a place where the temperature is between 0 C (32 F) and 40 C (104 F) and the humidity is between 20% and 80% (with no condensation). [If you set the FAN CONTROL to HIGH (page 43), set up the projector in a Remedy place where the temperature is between 0 C (32 F) and 35 C (95 F) and the humidity is between 20% and 80% (with no condensation).] B Disconnect the power cord by following the procedure on page 24, and then clean the air filter. (Refer to page 49)
46-ENGLISH
ENGLISH-47
# Press the F, G, I and H buttons to select the characters, then press the ENTER button. (You can enter 22 characters continuously.) C Select BS to delete a character. $ Press the F, G, I and H buttons to select OK, then press the ENTER button. C Select Cancel to cancel the change.
Cleaning and replacing the air filter

LAMP indicator Indicator display Illuminated (red) Flashing (red) An abnormality has been detected in the lamp circuit. If the air filter becomes clogged with dust, the internal temperature of the projector will rise, the TEMP indicator will flash and the projector power will turn off. The air filter should be cleaned every 100 hours of use.
Cleaning
Use a vacuum cleaner to clean off any accumulated dust.
Replacement procedure
# Turn off the power and disconnect the power cord. Be sure to disconnect the power cord by following the procedure given on page 24. $ Gently turn the projector upside down, and then remove the air filter cover.
It is nearly time to Problem replace the lamp unit.
B Does REPLACE B The power may B There may be an LAMP appear on have been turned abnormality in the Possible the screen after on straight away lamp circuit. cause the projector is after it was turned turned on? off. B This occurs when B Wait for a while B Disconnect the the operation time until the lamp unit power cord by for the lamp unit is cools down before following the nearing 1 800 turning the power procedure on hours (when back on again. page 24, and then LAMP POWER contact an has been set to Authorized Remedy HIGH). Ask your Service Center. dealer or an Authorized Service Center to replace the lamp unit. NOTE: B Be sure to disconnect the power cord by following the procedure given in Turning off the power on page 24 before carrying out any of the procedures in the Remedy column. B If the power turns off after the TEMP indicator starts flashing, it means an abnormality has occurred. Please contact an Authorized Service Center so that the necessary repairs can be made.
Air filter cover NOTE: B If the dust cannot be cleaned by a vacuum cleaner, remove the air filter and soak it in water, and then wash out the dust by hand. Be sure to install the air filter after it has dried. B Do not use detergent when washing the air filter. B If the dust cannot be removed by cleaning, it is time to replace the air filter. Please consult your dealer. Furthermore, if the lamp unit is being replaced, replace the air filter at this time also. Air filter cover % Replace the air filter, and then install the air filter cover.
Air filter NOTE: B Be sure to install the air filter before using the projector. If the projector is used without the air filter installed, dust and other foreign particles will be drawn into the projector, and malfunctions will result.
48-ENGLISH
ENGLISH-49
Replacing the lamp unit

Warning
The lamp unit should only be replaced by a qualified technician. When replacing the lamp, allow it to cool for at least one hour before handling it. B The lamp cover gets very hot, and contact with it can cause burns.
On-screen display
LAMP indicator
Lamp unit replacement period

The lamp is a consumable product. Even when the full life of the bulb has not been exhausted, the brightness of the light will gradually decline. Therefore periodic replacement of the lamp is necessary. The intended lamp replacement interval is 2 000 hours, but it is possible that the lamp may need to be replaced earlier due to variables such as a particular lamps characteristics, usage conditions and the installation environment. Early preparation for lamp replacement is encouraged. The lamp will automatically shut off after approximately 10 minutes when 2 000 hours of use have been reached because of a much greater chance of it exploding after this time. NOTE: B The usage hours explained above are for use when the HIGH setting has been selected for LAMP POWER in the OPTION2 menu. If the LOW setting is selected, the brightness of the lamp will be less and life of the lamp can be extended. B While 2 000 hours is the intended replacement interval, it is not a period of time covered by warranty. Displayed for 30 seconds. Pressing any More than 1 800 hours button will clear the display. More than 2 000 hours Remains displayed until any button is pressed.
Illuminates red during image projection and standby mode.
Notes on replacing the lamp unit

B The light generating lamp is made of glass, so dropping it or allowing it to hit hard objects may cause it to burst. Be careful when handling the lamp. B Dispose of the removed old lamp with the same care that would be taken with a fluorescent light. B A Phillips screwdriver is necessary for removing the lamp unit. NOTE: B The projector is not supplied with a replacement lamp unit. Please ask your dealer for details. Lamp unit product no.: ET-LAM1 CAUTION: B Do not use any lamp unit other than the one with the product number indicated above.
Lamp unit replacement procedure

NOTE: B If the lamp usage time has passed 2 000 hours (when LAMP POWER has been set to HIGH), the projector will switch to standby mode after approximately 10 minutes of operation. The steps ) to - on the next page should thus be completed within 10 minutes. # Disconnect the power cord from the projector by following the procedure on page 24, and check that the area around the lamp unit has cooled down. $ Use a Phillips screwdriver to turn the lamp unit cover fixing screws at the bottom of the projector, and then remove the lamp unit cover. Lamp unit cover % Use a Phillips screwdriver to loosen the two lamp unit fixing screws until the screws turn freely. Then hold the handle of the lamp unit and gently pull it out from the projector. Handle
Lamp unit fixing screws & Insert the new lamp unit while making sure that the direction of insertion is correct, and then use a Phillips screwdriver to securely tighten the lamp unit fixing screws.
Lamp unit cover fixing screws
50-ENGLISH
ENGLISH-51
' Install the lamp unit cover, and then use a Phillips screwdriver to securely tighten the lamp unit cover fixing screws. NOTE: B Be sure to install the lamp unit and the lamp unit cover securely. If they are not securely installed, it may cause the protection circuit to operate so that the power cannot be turned on. ( Connect the power cord. ) Press the POWER button so that a picture is projected onto the screen. NOTE: B If the power cord was disconnected during projection when the projector was used the last time, projection will start after the power cord is connected (when POWER MEMORY in the OPTION2 menu is set to ON). Refer to page 44 for details. * Press the MENU button to display the MAIN MENU, and then press the F or G button to select OPTION2.
+ Press the ENTER button to display the OPTION2 menu, and then press the F or G button to select LAMP RUNTIME.
Before calling for service

Before calling for service, check the following points. Problem Possible cause Power does not B The power cord may not be connected. turn on. B The main power supply is not being supplied to the wall outlet. B TEMP indicator is illuminated or flashing. B LAMP indicator is illuminated or flashing. B The lamp unit cover has not been securely installed. No picture B The video signal input source may not be appears. connected properly. B The input selection setting may not be correct. B The BRIGHT adjustment setting may be at the minimum possible setting. B The SHUTTER function may be in use. The picture is B The lens cover may still be attached to the lens. fuzzy. B The lens focus may not have been set correctly. B The projector may not be at the correct distance from the screen. B The lens may be dirty. B The projector may be tilted too much. The color is pale B COLOR or TINT adjustment may be incorrect. or grayish. B The input source which is connected to the projector may not be adjusted correctly. No sound can B The audio signal source may not be connected be heard. properly. B The volume adjustment may be at the lowest possible setting. The remote B The battery may be weak. control unit B The battery may not be inserted correctly. does not B The remote control signal receptor on the projector operate. may be obstructed. B The remote control unit may be out of the operation range. The buttons on B The CONTROL KEY may be set to OFF. the projector do In order to set the CONTROL KEY to ON not function. without using the remote control unit, keep holding down the ENTER button on the projector and press the MENU button for more than 2 seconds. Page 47 48 23 36 27 23 18 18 36
OPTION2 BACK COLOR BLUE FRONT/REAR FRONT DESK/CEILING DESK FAN CONTROL STANDARD LAMP POWER HIGH LAMP RUNTIME 1820H FUNC 1 INDEX CONTROL KEY ON AUTO POW.OFF DISABLE POWER MEMORY ON SELECT RETRN
, Press and hold the ENTER button for approximately 3 seconds.
The LAMP RUNTIME will change to TIME RESET [POWER OFF]. NOTE: B If the MENU button is pressed, the lamp time resetting screen will be cancelled.
21 21 21 44
EXIT
- Turn off the power. This will reset the cumulative usage time for the lamp unit to 0. Refer to page 24 for details on how to turn off the power.
52-ENGLISH
ENGLISH-53
OPTION2 BACK COLOR BLUE FRONT/REAR FRONT DESK/CEILING DESK FAN CONTROL STANDARD LAMP POWER HIGH TIME RESET [POWER OFF] FUNC 1 INDEX CONTROL KEY ON AUTO POW.OFF DISABLE POWER MEMORY ON SELECT RETRN
28, 31
Cleaning and maintenance

Problem Possible cause Page The picture does B The signal format (TV-SYSTEM) may not be set 36 not display correctly. correctly. B There may be a problem with the video tape or other signal source. B A signal which is not compatible with the projector 58 may be being input. Picture from B The cable may be too long. computer does B The external video output for the laptop computer not appear. may not be set correctly. (You may be able to change the external output settings by pressing the [Fn]+[F3] or [Fn]+[F10] keys simultaneously. The actual method varies depending on the type of computer, so refer to the documentation provided with your computer for further details.) B If an RGB INPUT indicator is turned off, the video 14 signals may not be output from the computer.
Before carrying out cleaning and maintenance, be sure to disconnect the power cord plug from the wall outlet.
Wipe the cabinet with a soft, dry cloth. If the cabinet is particularly dirty, soak the cloth in water with a small amount of neutral detergent in it, squeeze the cloth very well, and then wipe the cabinet. After cleaning, wipe the cabinet dry with a dry cloth. If using a chemically-treated cloth, read the instructions supplied with the cloth before use. Do not wipe the lens with a cloth that is dusty or which produces lint. If any dust or lint gets onto the lens, such dust or lint will be magnified and projected onto the screen. Use a blower to clean any dust and lint from the lens surface, or use a soft cloth to wipe off any dust or lint.
54-ENGLISH
ENGLISH-55
Specifications
Power supply: Power consumption: Amps: LCD panel: Panel size (diagonal): Aspect ratio: Display method: Drive method: Pixels: Lens: 100 V 240 V ~, 50 Hz/60 Hz 180 W [During standby (when fan is stopped): Approx. 5 W] 2.2 A 1.0 A VIDEO IN: S-VIDEO IN: AUDIO IN: Cabinet: Dimensions: Width: Height: Length: Weight: Operating environment: Temperature: Humidity: Certifications: <Remote control unit> Power supply: Operating range: Weight: Dimensions: Width: Length: Height: <Options> Ceiling bracket Wireless remote control unit Single-line, RCA pin jack 1.0 V [p-p], 75 Single-line, Mini DIN 4-pin Y 1.0 V [p-p], C 0.286 V [p-p], 75 Single-line, RCA pin jack x 2 (L-R) 0.5 V [rms] Moulded plastic (PC/ASA) 257 mm (10-3/32) 69 mm (2-11/16) 209 mm (8-7/32) (without lens cover) 1.6 kg (3.5 lbs.) 0 C 40 C (32 F 104 F) [When the FAN CONTROL is set to HIGH (page 43); 0 C 35 C (32 F 95 F)] 20% 80% (no condensation) UL60950, C-UL FCC Class B 3 V DC (Lithium CR2025 battery x1) Approx. 7 m (23) (when operated directly in front of signal receptor) 18 g (0.6 ozs.) (including battery) 40 mm (1-9/16) 6.5 mm (-1/4) 86 mm (3-3/8) ET-PKM1 ET-RM200
0.55 type (13.97 mm) 4:3 3 transparent LCD panels (RGB) Active matrix method 480 000 (800 x 600) x 3 panels Manual zoom (1 - 1.2) / Manual focus F 1.8 - 1.9, f 17.0 mm - 20.4 mm Lamp: UHM lamp (130 W) Luminosity: 1 200 lm Scanning frequency (for RGB signals): Horizontal scanning frequency: 15 kHz 91 kHz Vertical scanning frequency: 50 Hz 85 Hz Dot clock frequency: Less than 100 MHz YPBPR signals: 525i (480i), 525p (480p), 625i (576i), 625p (576p), 750p (720p), 1 125i (1 080i) Color system: 7 (NTSC/NTSC 4.43/PAL/PAL-M/PAL-N/ PAL60/SECAM) Projection size: 838.2 mm - 7 620 mm (33 - 300) Throw distance: 1.2 m - 10.9 m (311 - 359) Optical axis shift: 6:1 (fixed) Screen aspect ratio: 4:3 Installation: Front/Rear/Ceiling/Desk (Menu selection method) Speaker: 2.8 cm round x 1 Max. useable volume output: 1 W (mono) Connectors RGB IN: Single-line, D-SUB HD 15-pin (female) During YPBPR input: Y: 1.0 V [p-p] (Including sync), 75 PB, PR : 0.7 V [p-p], 75 During RGB input: R.G.B.: 0.7 V [p-p], 75 G.SYNC: 1.0 V [p-p], 75 HD/SYNC: TTL, automatic plus/minus polarity compatible VD: TTL, automatic plus/minus polarity compatible
56-ENGLISH
ENGLISH-57
Others
Appendix
List of compatible signals
Mode
NTSC/NTSC4.43/ PAL-M/PAL60 PAL/PAL-N/SECAM 525i 625i 525p 625p HDTV60 HDTV50 750p VGA400 VGA480
Connector pin wiring

Scanning frequency H V (kHz) (Hz)
15.734 15.625 15.734 15.625 31.469 31.250 33.750 28.125 45.000 31.469 37.861 31.469 35.000 37.861 37.500 43.269 35.156 37.879 48.077 46.875 53.674 49.725 48.363 56.476 60.023 68.678 35.520 63.995 67.500 76.705 68.681 60.000 63.981 79.977 91.146 63.981 75.000 59.940 50.000 59.940 50.000 59.940 50.000 60.000 50.000 60.000 70.086 85.081 59.940 66.667 72.809 75.000 85.008 56.250 60.317 72.188 75.000 85.061 74.550 60.004 70.069 75.029 84.997 86.952 71.184 74.917 85.038 75.062 60.000 60.020 75.025 85.024 60.020 60.000 13.500 13.500 27.000 27.000 74.250 74.250 74.250 25.175 31.500 25.175 30.240 31.500 31.500 36.000 36.000 40.000 50.000 49.500 56.250 57.283 65.000 75.000 78.750 94.500 44.897 94.200 108.000 121.500 100.000 108.000 108.000 135.001 157.500 108.000 162.000
Display resolution (dots)*1

720 x 480i 720 x 576i 720 x 480i 720 x 576i 720 x 483 720 x 576 1 920 x 1 080i 1 920 x 1 080i 1 280 x 720 640 x 400 640 x 400 640 x 480 640 x 480 640 x 480 640 x 480 640 x 480 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 832 x 624 1 024 x 768 1 024 x 768 1 024 x 768 1 024 x 768 1 024 x 768i 1 152 x 864 1 152 x 864 1 152 x 864 1 152 x 870 1 280 x 960 1 280 x 1 024 1 280 x 1 024 1 280 x 1 024 1 400 x 1 050 1 600 x 1 200
Dot clock Picture frequency RESIZING*3 quality*2 (MHz)

A A A A A A A A A A A A A A A A AA AA AA AA AA A A A A A A A B B B B B B B B B OK OK OK OK OK OK
Format
Video/S-Video Video/S-Video YPBPR/RGB YPBPR/RGB YPBPR/RGB YPBPR/RGB YPBPR/RGB YPBPR/RGB YPBPR/RGB RGB RGB RGB RGB RGB RGB RGB RGB RGB RGB RGB RGB RGB RGB RGB RGB RGB RGB RGB RGB RGB RGB RGB RGB RGB RGB RGB RGB
B The pin layout and signal names for the S-VIDEO IN connector are shown below. Pin No. Signal # $ Earth (Luminance signal) # Earth (Color signal) $ Luminance signal % % & External view Color signal & B The pin layout and signal names for the RGB IN connector are shown below. Pin No. Signal 1 R/PR # G/GSYNC/Y $ ( , B/PB % SDA . # ' HD/SYNC / VD 0 External view SCL 1 Pin & and + are spare. Pins ' *, , and - are for earth. Pins . and 1 functions are only valid when supported by the computer.
*4
OK OK OK OK OK OK OK
SVGA
*4
MAC16 XGA
Projection dimensions calculation methods

If the screen size (diagonal) is SD (m), then the following formula is used to calculate the projection distance for the wide lens position (LW) and the projection distance for the telephoto lens position (LT).
4:3
SD
*4
MXGA MAC21 MSXGA SXGA
For 16:9 aspect ratios, the following formula can be used to calculate the projection distance. Minimum Projection Distance (mm) LW=33.902xSD/0.0254-42.524 Maximum Projection Distance (mm) LT=40.359xSD/0.0254-42.519 *The values obtained from the formulas above are approximate.
*3 *4
58-ENGLISH
ENGLISH-59
Others
*1 *2
*4 *4 The i appearing after the resolution indicates an interlaced signal. The following symbols are used to indicate picture quality. AA Maximum picture quality can be obtained. A Signals are converted by the image processing circuit before picture is projected. B Some loss of data occurs to make projection easier. Signals with OK in the RESIZING column can be set using the RESIZING command in the POSITION menu. (page 40) Signals that are compatible with the FRAME LOCK function. (page 40)
UXGA
LW/LT
H1
*4 *
SH
SW
Minimum Projection Distance (mm) LW=30.919xSD/0.0254-42.514 Maximum Projection Distance (mm) LT=36.766xSD/0.0254-42.233
Dimensions
<Units: mm (inch)>
NOTES IMPORTANTES CONCERNANT LA SCURIT

AVERTISSEMENT: POUR REDUIRE LES RISQUES DE FEU OU DE CHOC
LECTRIQUE, NE PAS EXPOSER CE PRODUIT LEAU OU LHUMIDIT
209 (8-7/32)
257(10-3/32)
10(-3/8)
63.5(2-1/2)
40(1-9/16)
69(2-11/16)
Alimentation: Ce projecteur LCD est conu pour fonctionner sur secteur de 100 V - 240 V, 50 Hz/60 Hz seulement. ATTENTION: Le cordon dalimentation secteur fourni avec le projecteur peut tre utilis uniquement pour une alimentation lectrique de 125 V, 7 A maximum. Si on veut lutiliser avec une tension ou un courant plus forts, on doit se procurer un autre cordon dalimentation de 250 V. Si on utilise le cordon fourni sous ces conditions, risque de provoquer un incendie.
Trademark acknowledgements
B VGA and XGA are trademarks of International Business Machines Corporation. B Macintosh is a registered trademark of Apple Computer, Inc. B S-VGA is a registered trademark of the Video Electronics Standards Association. All other trademarks are the property of the various trademark owners.
Le symbole de la flche en forme dclair, dans un triangle, avertit lusager de la prsence de tensions dangereuses lintrieur du produit qui peuvent tre de force suffisante pour constituer un risque de choc lectrique aux personnes. Le point dexclamation dans un triangle avertit lusager de la prsence dinstructions importantes concernant lutilisation et lentretien (rparation) dans la littrature accompagnant le produit.
These Operating Instructions are printed on recycled paper.
ATTENTION: Cet appareil est quip dune fiche de courant trois broches avec mise la terre. Ne pas retirer la broche de mise la masse de la Ne pas retirer fiche. Cette fiche ne pourra tre utilise que dans une prise avec mise la terre. Ceci est une prcaution scuritaire. Sil est impossible dinsrer la fiche dans la prise, sadresser un lectricien. Ne pas annuler la protection de la fiche mise la terre.
60-ENGLISH
FRANAIS-61
Others
AVERTISSEMENT: B Ne peut tre utilis dans une salle dordinateurs telle que dfinie dans la norme ANSI/NFPA 75 Standard for Protection of Electronic Computer/Data Processing Equipment. B Pour lquipement branch en permanence, un dispositif de disconnexion daccs facile doit tre incorpor dans le cble dinstallation du btiment; B Pour lquipement branchable, une prise secteur daccs facile doit tre installe prs de lquipement.
Prcautions de scurit
AVERTISSEMENT
Si lon remarque une mission de fume, dodeurs suspectes ou de bruits provenant du projecteur, dbrancher la fiche du cordon dalimentation de la prise de courant. B Ne pas continuer dutiliser le projecteur dans ces cas, autrement cela peut entraner un incendie ou des chocs lectriques. B Aprs stre assur que de la fume ne se dgage plus, sadresser un centre technique agr et demander que les rparations ncessaires soient faites. B Le fait de rparer le projecteur soi-mme est trs dangereux, et ne doit jamais tre fait. Ne pas installer ce projecteur dans un endroit qui nest pas assez rsistant pour supporter le poids du projecteur. B Si lemplacement dinstallation nest pas assez rsistant, le projecteur risque de tomber et causer de graves blessures et (ou) des dommages. Demander un technicien qualifi dinstaller le projecteur par exemple sil est install au plafond. B Si linstallation nest pas faite correctement, cela peut entraner des blessures ou des chocs lectriques. Si de leau ou des objets trangers entrent dans le projecteur, si le projecteur tombe, ou si le botier est endommag, teindre lappareil et dbrancher immdiatement la fiche dalimentation de la prise de courant. B Si lon continue dutiliser le projecteur dans cette condition, cela peut entraner un incendie ou des chocs lectriques. B Sadresser un centre technique agr pour que les rparations ncessaires puissent tre faites. Ne pas surcharger la prise de courant. B Si lalimentation est surcharge (par exemple, par lutilisation de trop dadaptateurs), cela risque de faire surchauffer le projecteur et peut entraner un incendie. Ne pas retirer le capot ou le modifier. B Des hautes tensions qui peuvent causer de graves blessures sont prsentes lintrieur du projecteur.
B Pour toute inspection, rglage ou rparation, sadresser un centre technique agr. Nettoyer la fiche du cordon dalimentation rgulirement afin dviter toute accumulation de poussire. B Si de la poussire saccumule sur la fiche du cordon dalimentation, lhumidit peut endommager lisolant et entraner un incendie. Dbrancher le cordon dalimentation de la prise de courant et lessuyer avec un tissu sec. B Si le projecteur nest pas utilis pendant une priode prolonge, dbrancher le cordon dalimentation de la prise de courant. Faire attention ne pas endommager le cordon dalimentation. B Ne pas endommager le cordon dalimentation, ne pas le modifier, ne pas le placer sous des objets lourds, ne pas le chauffer, ne pas le placer prs dobjets chauffants, ne pas le tordre, ne pas le plier ou le tirer excessivement et ne pas le rouler en boule. B Si le cordon dalimentation est endommag, cela peut entraner un incendie et des chocs lectriques. B Si le cordon dalimentation est endommag, le faire rparer par un centre technique agr. Ne pas manipuler le cordon dalimentation avec les mains mouilles. B Cela peut entraner des chocs lectriques. Brancher la fiche du cordon dalimentation fermement dans la prise de courant. B Si la fiche nest pas compltement insre, cela peut entraner des chocs lectriques ou la faire surchauffer. B Si la fiche est endommage ou la plaque de la prise est desserre, elles ne devraient pas tre utilises. Ne pas placer le projecteur sur des surfaces instables. B Si le projecteur est plac sur une surface qui est incline ou instable, il risque de tomber ou de se renverser et cela peut causer des blessures ou des dommages. Ne pas placer le projecteur dans leau ou ne pas le laisser se mouiller. B Sinon cela peut causer un incendie ou des chocs lectriques. Ne pas placer des rcipients de liquide sur le projecteur. B Si de leau se renverse sur le projecteur ou pntre dans celui-ci, il y aura risque dincendie ou dlectrocution. B Si de leau entre lintrieur du projecteur, entrer en contact avec un centre technique agr. Ne pas mettre dobjets trangers dans le projecteur. B Ne pas insrer dobjets mtalliques ou inflammables dans les orifices de ventilation ou les faire tomber sur le projecteur, car cela peut causer un incendie ou des chocs lectriques. Garder les piles hors de porte des enfants. B Si les piles sont ingres, il y aura risque de dcs par touffement. En cas dingestion des piles, consulter immdiatement un mdecin.
62-FRANAIS
FRANAIS-63
Others
Veiller ce que les bornes + et - des piles nentrent pas en contact avec des objets mtalliques tels que colliers ou pingles cheveux. B Sinon, les piles risqueront de fuir, de surchauffer, dexploser ou de prendre feu. B Ranger les piles dans un sac en plastique, et ne pas les ranger proximit dobjets mtalliques. Pendant un orage, ne pas toucher le projecteur ou le cble. B Il y a risque dlectrocution. Ne pas utiliser lappareil dans un bain ou une douche. BIl y a risque dincendie ou dlectrocution. Ne pas regarder directement dans lobjectif pendant que le projecteur fonctionne. B Une lumire intense est mise par lobjectif du projecteur. Si lon regarde directement dans cette lumire, elle risque de causer des blessures et de graves lsions aux yeux. B Veiller particulirement ne pas laisser les jeunes enfants regarder dans lobjectif. En outre, dbrancher le cordon dalimentation secteur lorsquon laisse le projecteur sans surveillance. Ne pas placer les mains ou autres objets prs de lorifice de sortie dair. B De lair chaud sort par lorifice de sortie dair. Ne pas placer les mains, le visage, ou dautres objets qui ne peuvent rsister la chaleur prs de cette sortie dair, sinon des brlures ou des dommages risqueraient de sensuivre. Le remplacement de lunit de lampe ne devrait tre effectu que par un technicien qualifi. B Le bloc de lampe a une haute pression interne. Sil est mal manipul, une explosion peut sensuivre B Le bloc de lampe peut tre facilement endommag sil est cogn contre des objets durs ou si on le laisse tomber, pouvant entraner des blessures ou des mauvais fonctionnements. Lors du remplacement de la lampe, la laisser refroidir pendant au moins une heure avant de la manipuler. B Le couvercle de la lampe devient trs chaud, et on risque de se brler si on le touche. Avant de remplacer la lampe, veiller dbrancher le cordon dalimentation de la prise de courant. B Il y a risque dlectrocution ou dexplosion.
Attention
Ne pas obstruer les orifices dentre et de sortie dair. B Cela risque de faire surchauffer le projecteur, et causer un incendie ou endommager le projecteur. B Ne pas installer le projecteur dans des endroits troits, mal ventils tels que des placards ou des rayons livres.
B Ne pas placer le projecteur sur des tissus ou du papier, ces matriaux peuvent tre aspirs dans lorifice dentre dair. Ne pas installer le projecteur dans des endroits humides ou poussireux ou dans des endroits o le projecteur peut entrer en contact avec de la fume ou la vapeur. B Lutilisation du projecteur dans de telles conditions peut causer un incendie ou des chocs lectriques. Pour dbrancher le cordon dalimentation, tenir la fiche et non pas le cordon. B Si le cordon dalimentation est tir, le cordon sera endommag et cela peut causer un incendie, des courts-circuits ou des chocs lectriques srieux. Dbrancher toujours tous les cbles avant de dplacer le projecteur. B Le fait de dplacer le projecteur avec des cbles branchs peut endommager les cbles, ce qui pourrait causer un incendie ou des chocs lectriques. Ne pas placer dobjets lourds sur le projecteur. B Cela peut dsquilibrer le projecteur et le faire tomber, ce qui peut entraner des dommages ou des blessures. Ne pas court-circuiter, chauffer ou dmonter les piles, et ne pas les mettre dans leau ou dans le feu. B Sinon, les piles risqueront de surchauffer, de fuir, dexploser ou de prendre feu, et donc de causer des brlures ou dautres blessures. Lorsquon insre les piles, veiller ce que les polarits (+ et -) soient bien respectes. B Si lon insre les piles incorrectement, elles risqueront dexploser ou de fuir, ce qui peut causer un incendie, des blessures ou une contamination du logement des piles et de la zone environnante. Utiliser uniquement les piles spcifies. B Si lon utilise des piles incorrectes, elles risqueront dexploser ou de fuir, ce qui peut causer un incendie, des blessures ou une contamination du logement des piles et de la zone environnante. Isoler la pile laide dadhsif ou autre avant de la mettre au rebut. B Si la pile entre en contact avec des objets mtalliques ou dautres piles, elle peut prendre feu ou clater. Ne pas peser de tout son poids sur ce projecteur. B On risque de tomber ou de casser lappareil, ce qui peut causer des blessures. B Veiller tout particulirement ce que des enfants ne montent pas sur lappareil. Si lon nutilise pas le projecteur pendant une priode prolonge, dbrancher la fiche du cordon dalimentation de la prise de courant. B Si de la poussire saccumule sur la fiche du cordon dalimentation, lhumidit ainsi cre risquera dendommager lisolation, ce qui peut provoquer un incendie. B Ce projecteur continue de consommer environ 5 W de courant, mme lorsque lalimentation lectrique est coupe.
64-FRANAIS
FRANAIS-65
Others
Dbrancher la fiche du cordon dalimentation de la prise de courant comme mesure de scurit avant deffectuer tout nettoyage. B Sinon cela peut causer des chocs lectriques. Demander un centre technique agr de nettoyer lintrieur du projecteur au moins une fois par an. B Sil nest pas nettoy et que de la poussire saccumule lintrieur du projecteur, cela peut causer un incendie ou des problmes de fonctionnement. B Il est recommand de nettoyer lintrieur du projecteur avant que la saison humide narrive. Demander au centre technique agr le plus proche de nettoyer le projecteur lorsque cela est requis. Se renseigner auprs du centre technique agr pour le cot du nettoyage. Nous faisons tous les efforts possibles afin de prserver lenvironnement. Prire dapporter lappareil, sil nest pas rparable, votre revendeur ou un centre de recyclage.
Ne pas installer le projecteur prs de lignes dalimentation lectrique haute tension ou de moteurs. Le projecteur peut tre soumis des interfrences lectromagntiques. Si le projecteur est install au plafond, demander un technicien qualifi de faire tous les travaux dinstallation. Il faut acheter le kit dinstallation spar (numro de modle: ET-PKM1). En outre, tous les travaux dinstallation doivent tre excuts uniquement par un technicien qualifi. Si lon utilise ce projecteur un endroit lev (au-dessus de 1 400 m), rgler le VENTILATEUR sur FORT (se rfrer la page 43). Sinon, des anomalies pourront se produire.
Notes sur lutilisation

Afin dobtenir la meilleure qualit dimage Fermer les rideaux ou les volets de toutes les fentres et teindre les lampes fluorescentes situes proximit de lcran afin que la lumire extrieure ou la lumire des lampes intrieures nclaire pas lcran. Ne pas toucher aux surfaces de lobjectif avec les mains nues. Si la surface de lobjectif est salie par des empreintes digitales ou autre, ceci sera agrandi et projet sur lcran. Dailleurs, lorsque le projecteur nest pas utilis, rtracter lobjectif, puis la couvrir laide du capuchon dobjectif. propos de lcran Nappliquer aucun produit volatil qui risque de dcolorer lcran, et veiller ce que lcran ne soit pas sale ou endommag. A propos de la lampe Il est possible quil faille remplacer la lampe plus tt en raison de facteurs variables comme les caractristiques de la lampe, des conditions dutilisation et un environnement dinstallation particuliers, en particulier si elle est utilise de faon continue pendant plus de 10 heures ou si lalimentation est frquemment mise en et hors circuit.
Avant lutilisation
Prcaution prendre lors du dplacement du projecteur
Veiller fixer le capuchon dobjectif avant de dplacer le projecteur. Lobjectif de projection est trs sensible aux vibrations et aux chocs. Lorsquon dplace le projecteur, utiliser la housse fournie. Lorsquon place le projecteur dans la housse, le placer de faon que lobjectif soit orient vers le haut.
Avertissements concernant linstallation

viter de linstaller dans les endroits sujets des vibrations ou des chocs. Les pices internes peuvent tre endommages, ce qui peut causer des pannes ou des accidents.
66-FRANAIS
FRANAIS-67
Others
Fixer le capuchon dobjectif de faon que le logo Panasonic soit dans le sens indiqu sur lillustration ci-dessus.
propos de laffichage cristaux liquides Laffichage cristaux liquides du projecteur est fabriqu en utilisant une technologie de trs haute prcision permettant dobtenir des images trs dtailles. Parfois, il est possible que des pixels non actifs apparaissent sur lcran sous forme de points fixes bleus, verts ou rouges. Bien noter que ceci naffecte pas le fonctionnement du LCD.
Remplacement du bloc de lampe

AVERTISSEMENT
Le bloc de lampe ne devrait tre remplac que par un technicien qualifi. Lors du remplacement de la lampe, la laisser refroidir pendant au moins une heure avant de la manipuler. B Le couvercle de la lampe devient trs chaud, et on risque de se brler si on le touche.
Affichage lcran
Indicateur LAMP
Priode de remplacement du bloc de lampe

La lampe est un produit qui doit tre remplac. Mme si la dure de vie complte de lampoule nest pas encore puise, la luminosit de la lampe diminuera progressivement. Il faut donc remplacer priodiquement la lampe. Lintervalle de remplacement de la lampe prvu est de 2 000 heures; il est toutefois possible quil faille remplacer la lampe avant ce dlai en raison dlments variables comme les caractristiques particulires de la lampe, les conditions dutilisation et lenvironnement dinstallation. Il est recommand de toujours avoir un bloc de lampe de rechange prt lemploi. La lampe steindra automatiquement aprs environ 10 minutes lorsque la limite de 2 000 heures dutilisation est atteinte, car le risque dexplosion de la lampe devient beaucoup plus grand pass cette limite. REMARQUE: B Les heures dutilisation expliques ci-dessus concernent lutilisation lorsque le rglage FORTE a t slectionn pour PUIS.LAMPE dans le menu OPTION2. Si le rglage FAIBLE est slectionn, la luminosit de la lampe sera moindre et la dure de vie de la lampe sera allonge. B Bien que le dlai de 2 000 heures soit lintervalle de remplacement prvu, lobtention de cette dure nest pas couverte par la garantie. Plus de 1 800 heures Affich pendant 30 secondes. Laffichage disparat si lon appuie sur Sallume en rouge nimporte quelle touche. pendant que limage est Reste affich jusqu ce projete et en mode dattente. quune touche quelconque soit presse.
Plus de 2 000 heures
Notes sur le remplacement du bloc de lampe

B La lampe produisant la lumire est en verre; il ne faut donc pas la laisser tomber ou la cogner contre des objets rigides, car elle risquerait dclater. Faire bien attention lorsquon manipule la lampe. B Jeter la lampe usage de la mme manire quune lampe fluorescente. B Il faut utiliser un tournevis Phillips pour dposer le bloc de lampe. REMARQUE: B Le projecteur nest pas fourni avec un bloc de lampe de rechange. Demander les dtails au revendeur. Numro de produit du bloc de lampe: ET-LAM1 ATTENTION: B Ne pas utiliser un bloc de lampe avec un numro de pice autre que celui indiqu ci-dessus.
Mthode de remplacement du bloc de lampe

REMARQUE: B Si le temps dutilisation de la lampe a dpass 2 000 heures (lorsque PUIS.LAMPE a t mis sur FORTE), le projecteur passe en mode dattente aprs environ dix minutes de fonctionnement. Ds lors, faire les tapes ) - la page suivante dans les 10 minutes. # Dbrancher le cordon dalimentation du projecteur en procdant comme indiqu la page 24, puis vrifier si la zone environnant le bloc de lampe sest bien refroidie. $ Utiliser un tournevis Phillips pour desserrer les vis de fixation du couvercle du bloc de lampe sur le fond du projecteur, puis enlever le couvercle du bloc de lampe. Couvercle du bloc de lampe % Utiliser un tournevis Phillips pour desserrer les deux vis de fixation du bloc de lampe jusqu ce que les vis tournent librement. Tenir la poigne du bloc de lampe et tirer doucement pour le sortir du projecteur. Poigne
Vis de fixation du couvercle du bloc de lampe
& Insrer le nouveau bloc de lampe tout en sassurant que le sens dinsertion est correct, puis utiliser un tournevis Phillips pour resserrer fermement les vis de fixation du bloc de lampe.
68-FRANAIS
FRANAIS-69
Others
Vis de fixation du bloc de lampe
' Installer le couvercle du bloc de lampe, puis utiliser un tournevis Phillips pour resserrer fermement les vis de fixation du couvercle du bloc de lampe. REMARQUE: B Sassurer de bien installer le bloc de lampe et le couvercle du bloc de lampe. Sils ne sont pas bien installs, cela peut dclencher le circuit de protection et le projecteur ne pourra pas tre allum. ( Brancher le cordon dalimentation. ) Appuyer sur la touche POWER pour projeter une image sur lcran. REMARQUE: B Si le cordon dalimentation a t dbranch pendant la projection lorsque le projecteur a t utilis la fois prcdente, la projection senclenchera aprs quon ait branch le cordon dalimentation (lorsque MEMOIRE ALIM dans le menu OPTION2 est rgl sur OUI). Pour plus de dtails, se reporter la page 44. * Appuyer sur la touche MENU pour faire apparatre le MENU PRINCIPAL, puis appuyer sur la touche F ou G pour slectionner OPTION2.
+ Appuyer sur la touche ENTER pour faire apparatre le menu OPTION2, puis appuyer sur la touche F ou G pour slectionner DURE LAMPE.
OPTION2 COULEUR FOND BLEU INSTALLATION FAADE SOL/PLAFOND SOL VENTILATEUR STANDARD PUIS.LAMPE FORTE DURE LAMPE 1820H FONCTION 1 RGL TOUCHE CTRL OUI ARRET AUTO INACTIF MEMOIRE ALIM OUI SL. ESC
, Maintenir la touche ENTER enfonce pendant environ 3 secondes.
OPTION2 COULEUR FOND BLEU INSTALLATION FAADE SOL/PLAFOND SOL VENTILATEUR STANDARD PUIS.LAMPE FORTE INIT COMPT [POWER OFF] FONCTION 1 RGL TOUCHE CTRL OUI ARRET AUTO INACTIF MEMOIRE ALIM OUI SL. ESC
DURE LAMPE changera INIT COMPT [POWER OFF]. REMARQUE: B Si la touche MENU est presse, lcran de remise zro de la dure de lampe sera annul. - Couper lalimentation lectrique. Le temps dutilisation total du bloc de lampe est alors remis zro. Pour plus de dtails concernant la mise hors tension, se reporter la page 24.
MENU COR TRAP IMAGE POSITION RGL FENETRE OBTURATEUR VOLUME LANGAGE OPTION1 OPTION2 SECURITE SL. VALID
SORT.
70-FRANAIS

Operating Instructions: Pt-Lm1U

Uploaded by

Copyright:

Available Formats

Operating Instructions: Pt-Lm1U

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Operating Instructions: Pt-Lm1U

Uploaded by

Copyright:

Available Formats

R

LCD Projector Commercial Use

STD VOLUME INDEX WINDOW D.ZOOM

Dear Panasonic Customer:

Model number: PT-LM1U Serial number:

IMPORTANT SAFETY NOTICE

Precautions with regard to safety

Care and maintenance

Adjustments and settings

RGB signal cable [1.8 m (510), K1HA15DA0002 x1]

Power cord (K2CG3DR00005 x 1)

STD VOLUME INDEX WINDOW D.ZOOM

Cautions regarding setting-up

Caution when moving the projector

Location and function of each part

Projector control panel <Top> # ' ( $ )

% & Remote control unit ' ) +

Setting FRONT DESK

Menu items FRONT/REAR DESK/CEILING

Setting FRONT CEILING

BRear-desk projection (Using a translucent screen)

BRear-ceiling projection (Using a translucent screen)

Menu items FRONT/REAR DESK/CEILING

Setting REAR DESK

Menu items FRONT/REAR DESK/CEILING

Setting REAR CEILING

H1 Bottom edge of screen

Height position (H1)

RGB signal cable (accessory)

Preparation for the remote control unit

DVD player (with component video jack)

Turning on the power

VIDEO RGB S-VIDEO

STD VOLUME INDEX WINDOW D.ZOOM

the angle ' Adjusting BWhile pressing the adjuster buttons,

the accessory power cord to the AC IN # Connect socket.

the AUTO SETUP button to initiate ( Press automatic positioning.

Press the POWER button.

Turning off the power

STD VOLUME INDEX WINDOW D.ZOOM

POWER OFF OK CANCEL

Direct power off function

Correcting keystone distortion and automatic positioning (AUTO SETUP)

Turning off the picture and sound momentarily (SHUTTER)

Projected image B Automatic positioning will be carried out.

STD VOLUME INDEX WINDOW D.ZOOM

STD VOLUME INDEX WINDOW D.ZOOM

Projector control panel

Pausing a picture (FREEZE)

Press the FREEZE button.

STD VOLUME INDEX WINDOW D.ZOOM

Enlarging the picture (D.ZOOM)

Displaying two screens (INDEX WINDOW)

Press the D.ZOOM +/- button.

FREEZE FREEZE SHUTTER

STD VOLUME INDEX WINDOW D.ZOOM

STD VOLUME INDEX WINDOW D.ZOOM

Still Moving picture picture

Adjusting the volume (VOLUME)

Dot clock Picture frequency RESIZING3 quality2 (MHz)