GRISWOLD

ANSI

CENTRIFUGAL
PUMPS FOR THE
PROCESSING
INDUSTRY

P E R F O R M A N C E
D A R E

T O

C O M P A R E

GRISWOLD

M O V E

WHAT DRIVES YOUR PUMP

SELECTION PROCESS?

GRISWOLD:
ANYTHING BUT
STANDARD
The Griswold Pump Company is no newcomer to
pumps. With product lines
dating back over 70 years,
youll find a wealth of
industry knowledge and
experience behind every
Griswold product. At our
facility in Thomasville,
Georgia, we manufacture
a variety of pumps, including ANSI, end suction
centrifugals, self-priming
and submersible/vertical
turbines. With hundreds of
thousands of pump installations worldwide and our
international distribution
network, Griswold serves a
broad range of chemical
process, industrial and
municipal applications,
including:
Pulp and paper
Chemical
Petrochemical
Oil and gas
Textile
Breweries

ARE ALL ANSI

PUMPS THE SAME?
In 1977, the American National
Standards Institute (ANSI) established manufacturing criteria for
centrifugal pumps to ensure that
dimensional, material composition
and safety specifications meet the
demanding needs of the chemical
processing industry. Mandatory
design features, such as self-ventilation, foot mounting, centerline
discharge and back pullout,
became the industrys assurance
that complying pumps met production and safety needs.
Even though ANSI compliance
would seem to level the playing
field for pump specification, your
choices are actually far more complex. The fact is that many brands
just meet the minimal requirements
of this standard. And while other
brands may offer similar features
and performance, you may experience inflated cost, delayed delivery,
and deflated service. In a market
where all ANSI pumps seem the
same, dare to compare.

Grain processing
Food processing
Poultry processing
Automotive
Pharmaceutical
Steel
food processing

Semiconductor
Water treatment
Power generation

chemical

Y O U R

In a rapidly changing world market, theres no longer room for

making business decisions based on convention or costly old
relationships. Every angle must be scrutinized to give your
production process the edge needed to survive economic
volatility and polarized competition.
Maximizing production and minimizing costs are as much functions of equipment performance as initial and long-term costs
of operating and maintaining equipment. Most importantly,
you must minimize the time and financial losses caused by production failures. As a result, pump specification must meet
even more demanding criteria than ANSI compliance:

1
2
3
4

Proven track record

of performance
Extended equipment life
Reduced initial cost and
total cost of ownership
Speed and ease of
repair or replacement

Dare to compare your ANSI pump. In a world where you need

every advantagewere confident youll choose Griswold.

ANSI PUMPS
H I G H E R

EXTENDED
EQUIPMENT LIFE:

PROVEN TRACK

RECORD OF
PERFORMANCE:

COMPARE

oil & gas

The Griswold 811 ANSI line

offers the best pumps youll find
on the market. Engineered for
exceptional performance and
maximum flexibility, our 811
models go the mile in the harshest and most difficult fluid processing applications. Griswolds
811 centrifugal pump not only
meets ANSI standards for chemical processing, it was among the
first pump designs to comply
with these standards in the
1970s. Almost 30 years of
proven performance has enabled
Griswold to focus on enhancing
our ANSI pump features and
support offerings to surpass the
industry standard and exceed
our customers expectations.

semiconductor

page 47

811
other
brands

S T A N D A R D

page 8 11

811

other
brands

Exceeding standard ANSI construction requirements, the Model

811 includes several additions
that are critical to long-term reliable function.To start,our superior
open impeller and seal chambers
are designed to facilitate corrosive and erosive substance transport, heat regulation and routine
maintenance. The 811s range of
enhanced power frames and
rigid base plates combine the latest technology with the highest
quality construction to minimize
the effects of work forces and
shaft deflection, optimize cooling and further simplify the
installation and maintenance
process. All told, you can expect
the 811 pump series to continue
performing long after other
ANSIs wear out or break down.

REDUCED INITIAL
& TOTAL COST
OF OWNERSHIP:

You may have heard that the initial cost of your pump and parts
plays a minor role in your total
cost of ownership. NOT TRUE!
With Griswolds 811, you get
identical quality and longevity as
the best-known brandsat a
lower initial price. Factor in our
low cost on parts, and your longterm savings are even greater!
This translates into your LOWEST
total cost of ownership.

SPEED AND EASE

OF REPLACEMENT:

COMPARE

COMPARE

T O

COMPARE

P R O C E S S

page 413

811

other
brands

When meeting your production

quota is compromised, each day
waiting for repairs can mean
significant losses in revenue
(another factor in your true cost
of ownership). The Griswold
811 and our extensive inventory
of parts are 100% interchangeable with hundreds
of thousands of other ANSI
pumps currently in use. With
stocking distributors from coastto-coast and throughout the
world, backed by Griswolds 36hour ship commitment (same
day on parts), and NO premium
charge for expedited shipment,
you can be up and going before
you may even get a response
call from our competition!

page 413

811
other
brands

And with our dedication to customer service, reduced response

times and engineering support,
Griswold stands ready to help
improve your process, increase
your productivity, lower your
costs and reduce your stress.

pharmaceutical
textile

GRISWOLD
F E A T U R E

ENGINEERED
FOR FLEXIBILITY
& DURABILITY
The Model 811 is available in a wide
range of sizes, capacities and materials to fit virtually any process fluid
application. With over 30 selections
and multiple design options, weve
got your application coveredfor
abrasive and corrosive substances, and
capacities ranging from 4 through
4000 gallons per minute.
Griswold maintains strict quality
assurance programs to ensure that
our entire product line is manufactured to the highest standard for
engineered tolerances:
Our American-produced investment
and no-bake casting processes
produce smooth, superior surface
finishes for consistent and reliable
performance.
A metallurgist-controlled annealing
process assures the maximum durability and product life available on
the market.
CNC (computer numerically controlled) machining equipment
guarantees consistency for all parts.
All power frames are assembled and
inventoried in our Clean Room to
keep sensitive bearings and internal
components contaminant-free.

F O R

F E A T U R E

LABYRINTH SEALS STANDARD:

INPRO oil seals keep outside contaminants
from lubrication media, significantly extending
bearing life. Standard in bronze. Carbon-filled
Teflon and magnetic face seals optional.

MOUNTING FRAME FLANGE:

Machined to accommodate C-face motor adapters.

C H A L L E N

DUCTILE IRON
FRAME ADAPTERS:
Ductile Iron construction provides
strength and safety. Precisionmachined fits accurately align the
liquid end to the power end. Large
openings simplify installation and
maintenance. Includes jacking
bolts to facilitate disassembly.

EXTRA LARGE CAPACITY

POWDER-COATED OIL SUMP:
Maximized oil capacity delivers improved
heat transfer and oil temperature, greatly
extending bearing life. Designed to
accommodate optional fin coolers
for higher temperature applications.
Impenetrable fusion bonded
epoxy coating on interior
surface extends quality,
cleanliness and longevity
of the lubricating oil.

EXTERNAL CLEARANCE
ADJUSTMENT:
For maintaining original flow, pressure
and efficiency, minimizing energy consumption and repairs, and extending
mean-time-between-failures (MTBF).

HEAVY-DUTY SHAFT & BEARINGS:

Engineered to minimize vibration and shaft deflection, less than 0.002 inch per ANSI B73.1, optimizing
pump life. Sleeved and solid shaft available in a variety of materials. Bearings sized for 10-year life under
tough operating conditions.

OVERSIZED SIGHT GLASS:

One-inch bulls eye reflective sight glass facilitates monitoring oil level and condition,
critical to bearing life. Bottle oiler optional.
P

MAGNETIC
DRAIN PLUG:
Collects damaging metallic
contaminants away from
the bearings.

ODELDESIGN
A N Y

C O M P E T I T I V E

B R A N D

EXTRA-HEAVY CASINGS:
Class 150 pumps incorporate Class 300 wall thickness as standard, extending reliability and casing life under severe corrosive/erosive conditions:
Top centerline, self-venting discharge for air handling
Back pull-out to simplify maintenance
Rigid casing feet prevent pipe load misalignment and promote
seal /casing life
Discharge connection for pressure gauge or seal bypass
flush connection standard on Ductile Iron and Stainless
Steel casings
Class 150 FF standard for positive sealing. Optional Class
150 RF 300 FF/RF available
Casing drain standard in Ductile Iron and Stainless
Steel for simplified maintenance.

FULLY OPEN IMPELLER:

Challenge your existing equipment quality, delivery and

costs with Griswolds ready-toship inventory of 811 pumps
and parts. Our high-quality,
ANSI-compliant pumps and
wearing parts will interchange
quickly and seamlessly with a
variety of ANSI pump models
and brands without piping,
baseplate or coupling changes.
All at a significant cost savings!
Factor in our NO PREMIUM
36-HR SHIP COMMITMENT
on pumps and SAME-DAY
SHIPPING on parts, and you'll
save money, simplify ordering, reduce inventory and
expedite line repair.

W I T H :

With double the wear area of enclosed

models, the 811 impeller offers superior
handling of solids, corrosives and abrasives.
Back pump-out vanes reduce hydraulic
loads and seal chamber pressure.

OPTIMIZE
YOUR PUMP
REPLACEMENT
PROCESS

SEALING FLEXIBILITY:
Wide range of sealing options coupled
with seal chambers and stuffing boxes
selected for service condition to improve
lubrication and heat dissipation of seal
faces, maximizing pump uptime.

CONTAINED
CASING GASKET:
Provides positive sealing at casing
joint to prevent blow out of liquids
and to facilitate disassembly.

I N T E R C H A N G E A B I L I T Y

G U I D E

I N T E R C H A N G E A B L E

G E S

PUMPS:

 Ductile Iron
pumps

 Stainless Steel
pumps

 Alloy 20 pumps
 CD4MCu pumps
PARTS:

 Bearings & seals

 Cases
 Impellers
 Power frames
 Shafts & sleeves
 Stuffing boxes
 all other parts for
ANSI pumps

All 811 parts, from end to end, are 100% interchangeable with many ANSI
pumps. Ask for our 56-page Parts Guideyour tool for cross-referencing
Griswold 811 to comparable pumps by size and part number!
P

GRISWOLD
A N S I

P R O C E S S

P U M P S

INCREASED CAPABILITY
FOR REDUCED VOLUMES
Standard ANSI pumps (with expanding
style volute casing) are not designed for
low flow, high head applications: the
excessive radial loads and shaft vibration
experienced can shorten bearing and seal
life. Griswolds Model 811LF series is
designed with a circular concentric casing in conjunction with a radial vane
impeller to reduce those excessive radial
loads and minimize shaft deflection, thus
extending MTBPM.

CIRCULAR CONCENTRIC
VOLUTE CASING:
The fully machined concentric volute reduces excessive radial loads experienced in low flow, high head
applications. Shaft vibration and deflection is minimized, extending bearing and mechanical seal life.
Class 150 raised face flanges are standard
with the Model 811LF series for positive sealing. Class 300 raised face flanges are available
as an option.

LOW FLOW RADIAL

VANE IMPELLER:
Griswolds radial vane impellers are specially
designed to reduce the thrust load and seal
chamber pressure normally associated with
low flow applications. When operating in
reduced volume conditions, the low flow
impellers vanes provide better hydraulic control than traditional ANSI impellers. Balance
holes reduce both axial thrust and seal chamber pressure, extending bearing and seal life.

LF
D E S I G N E D

F O R

FOR LOW FLOWS

L O W

F L O W

S E R V I C E S.
Ft.

1000
300
900
270

811LF PERFORMANCE:

Griswold 811LF pumps feature flow capacities as low

as 4 GPM, and heads as high as 920'low flow/high
head performance you can count on to further extend
your MTBPM.

total head (60Hz)

With a traditional ANSI pump, throttling or recirculating flow to attain low flow conditions causes excessive
radial load and shaft deflectionall of which can result
in premature failure to bearings and mechanical seals.

LF 3x11 /2 13
@3560 RPM

800
240

700
210

600
180

500
150

LF 2x1 10
@3560 RPM
120

90

400

300

60

200

30

100

LF 11 /2 x1 8
@3560 RPM
LF 3x11 /2 13
@1750 RPM
LF 2x1 10
@1750 RPM
LF 11/2 x1 8
@1750
RPM

petrochemical

0 GPM
0

25

3/ 5
h

50
10

75
15

100
20

125
25

150

30

175

35

200

40

45

225
50

250
55

capacity (60Hz)

SIX 811LF MODELS

LF 1 1/2 x 1 8 @ 1750 RPM
LF 1 1/2 x 1 8 @ 3500 RPM
LF 2 x 1 10 @ 1750 RPM
LF 2 x 1 10 @ 3500 RPM
LF 3 x 11/2 13 @ 1750 RPM
LF 3 x 11/2 13 @ 3500 RPM
811LF CAPACITIES

4 GPM
Heads

to
to

210 GPM
920'

RETROFITTING:
Griswold Model 811LF pumps are ANSI dimensional,
so they can be installed without piping or base changes
to existing equipment. In fact, since all other parts and
features are identical/interchangeable within the entire
811 ANSI line, the 811LF case and impeller can be
easily retrofitted to an existing Griswold pump as well
as 100,000s of other ANSI pumps already in service!
P

GRISWOLD
1

FO

HEAVY-DUTY
AMERICAN-MADE
CASTINGS:

C O M P A R E

S U P E R I O R C O N S T R U C T I O N. E X T R A O R D I N A R Y P E R F O

Increases
Performance
Increases
Longevity




Simplifies
Maintenance

Wide Choice of Materials. Your choice of

standard stocked materials for Model 811
centrifugal pumps includes Ductile Iron, 316
Stainless Steel, CD4MCu and Alloy 20. Other
alloys available.
Superior Casting Finishes. Investment and
no-bake casting processes ensure smooth, precise, superior finishes that guarantee consistent,
reliable performance.
Controlled Solution Annealing. Metallurgists
strictly supervise all heat-treating operations
to assure maximum corrosion-resistance for
all alloys.

C O M P A R E

FULLY OPEN IMPELLER:

Increases
Performance
Increases
Longevity




Simplifies
Maintenance

Ideally Suited for Chemical Process Industry Applications. Because it

has two times the area in the critical casing and stuffing box/seal chamber
clearances, Griswolds Open Impeller is far superior to its typical enclosed
counterpart. Our open design minimizes concentrated wear by balancing
hydraulic axial thrust load and reducing stuffing box pressure. This not only
facilitates corrosive, abrasive, solid and stringy fiber handling, but also simplifies maintenance, extends life and reduces repair costs.
Self-Tightening to Reduce Leaks and Failures. Our impeller design is further enhanced
by threading on the shaft and sealing through a controlled squeeze contained o-ring to eliminate bolt loosening with system changes or high temperatures. Metal-to-metal contact
ensures optimal running and transmittal of torque and alignment. Because we eliminate
the impeller bolt, we also eliminate corrosion or gasket leakage, ensuring that smooth
entrance contour and lower NPSH requirements are realized.
External Clearance Adjustment. Peak efficiency is ensured through simple maintenance to account for wear area loss. Adjustment is quick and easy to set at the site with
an ordinary open-end wrenchno shims or shop maintenance needed, as with enclosed
impellers. The external clearance adjustment moves the impeller forward to reestablish original clearance and hydraulic pressure without disassembly or replacement
of wear rings.
Back Pump-Out Vanes reduce pressure on the shaft seal and axial thrust on
the bearings. Maintenance is further simplifiedextending bearing life, seal life
and performance.
Investment Cast Impellers. Ultra-smooth, consistently cast investment impellers are
standard on Stainless Steel, CD4MCu and Alloy 20, and optional on Ductile Iron pumps.
This feature improves hydraulic and mechanical balance, maximizes seal and bearing life
and improves efficiency.

RTHELONGRUN
R M A N C E . E X C E P T I O N A L E N D U R A N C E.

SEAL CHAMBERS
& SEALING FLEXIBILITY:
Our quality seal chambers are engineered to provide optimum seal environment for
heat dissipation, solids, entrapped air and vapor. Oversized seal chambers increase radial
clearance between the mechanical seal and seal chamber, as well as provide better circulation of liquid to and from the seal faces, preventing failure of the shaft seal. A
variety of flush plans are available for additional lubrication and cooling of the seal faces.

Standard Bore

Large Bore

Tapered Bore

3-YEAR
Whole Pump
Warranty.
All 811 pumps are
backed by a 3-YEAR
unconditional
guarantee against
defects in material
and workmanship.


Most services including those
with solids greater than 10%.
Increased radial clearance
between seal & chamber for
improved liquid circulation,
lubrication & cooling.

Services up to 10% solids or

those containing entrained air
or vapors. For lower seal face
temperatures, self venting &
draining. Circulates solids &
vapors away from seal faces.

Services

Services utilizing packing or

mechanical seals. For mild
fluid at ambient temperatures.

Packing

Most Services

Not Available

Not Available

Single Seal/ No Flush

Not Recommended

Not Recommended

Services with Solids up to 10%

Single Seal/ With

Flush

Mild,
Clear Fluids

Most Services including

Solids above 10%

All Services with

Solids up to 10%

Conventional Double
Seal with Seal Plan

Zero Leakage
Applications

Zero Leakage
Applications

Not
Available

Cartridge Double
Seal with Seal Plan

Zero Leakage
Applications

Zero Leakage
Applications

Zero Leakage
Applications

Sealing Flexibility

SEAL SELECTION

 Single Inside Seal:

For non to moderately corrosive liquids, moderate abrasives

and liquids with good lubrication qualities.

 Conventional
Double Seal:

SEALS TO FIT
ANY APPLICATION:

Cartridge Seals, Component Seals & Conventional

Packing. With Griswolds broad selection of seals, you
can accommodate most any fluid and temperature for
demanding chemical, petroleum, pharmaceutical and
general industry applications. Our engineers can recommend the best seal to maximize your application
and system lifeincluding cartridge or component, single or double, inside or outside, balance or unbalanced
seals or conventional packing.

For liquids that are incompatible with single seals, cavitation

or low flow situations. Meets
environmental regulations for
toxic, hazardous, abrasive and
corrosive substances.

Cartridge Seal:
 Single
For same applications as con-

Single
Inside Seal

Conventional
Double Seal
Single
Cartridge Seal
Double
Cartridge Seal
Double Gas
Barrier Seal

ventional single seals, allowing

simplified seal setting and
maintenance.

Cartridge Seal:
 Double
For same applications as conventional double seals, allowing simplified seal setting and
maintenance.

Gas Barrier Seal:

 Double
Meets environmental regulations for toxic or hazardous
materials. For use when seal
pot or external flush is not
desirable or when compatible
seal flush liquid is not available.

GRISWOLD

FO

ENHANCED
POWER FRAMES:
INPRO Labyrinth Oil Seals. Our
high-quality oil seals keep outside
environmental contaminants from
entering your lubrication media,
greatly extending bearing life
available standard in bronze, and
optional in Carbon-filled Teflon or
magnetic seal face.
Large Sight Glass. Our one-inch
bulls eye sight glass simplifies oil
level and conditions monitoring,
critical to bearing life.
Large Oil Sump & Oversized Fill
Plug. Increased oil capacity maximizes heat transfer for reduced oil
temperature. Our extra large 1/ 2"
NPT oil fill plug further simplifies the
lubrication process. Designed to
accommodate optional fin coolers
for higher temperature applications.
Powder Coated Oil Sump Lining.
Griswold utilizes a Fusion Bonded
Epoxy Coating on the interior surface of the power frame to provide
an impenetrable barrier between
the iron frame and oil, enhancing
the long-term quality and cleanliness of the lubricating oil.

C O M P A R E

S U P E R I O R C O N S T R U C T I O N. E X T R A O R D I N A R Y P E R F O

Increases
Performance
Increases
Longevity




Simplifies
Maintenance

Improved Strength & Rigidity.

The superior tensile strength of
both our cast and ductile iron
makes Griswold power frames not
only stronger than the competitions (as much as 33%), but also
more rigidand better equipped
to withstand forces and moments
experienced in todays process
applications. (see chart next page)
Heavy-Duty Shaft & Bearings.
Our shaft is engineered for heavyduty loads and for minimum vibration and deflection at seal faces (less
than 0.002 inches per ANSI B73.1),
extending bearing and seal life.
Using only the highest-quality bearings further optimizes the 811s performance and reliability. Both shaft
and bearings are rated for 10-year
average life under tough operating
conditions. Standard hook-type
sleeved design meets ANSI shaft
deflection standards and provides
ease of maintenance. Solid shaft
design available for more demanding applications. Both are available
in a variety of materials.
Hook-Type Replaceable Shaft
Sleeve. The 811s hook-type shaft
sleeve is free to expand with temperature changes and promotes
renewal of the sealing surface without bearing and shaft disassembly.

1 0

Magnetic Drain Plug. Our drain

plug is designed to magnetically collect damaging metallic contaminants away from the bearings.
Monitoring Locations. Each
power frame is machined with 4
condition-monitoring sites to facilitate consistent checking of vibration and temperature.
Clean Room Assembly. All sizes
of our power frames are assembled
in Griswolds climate controlled,
sealed, clean room which filters out
airborne dirt and debris that might
otherwise contaminate sensitive
bearings and internal components.
We also inventory all finished power
frames and associated components
in this ultra clean environment to
ensure the most reliable power
frame you can buy.

RTHELONGRUN
R M A N C E . E X C E P T I O N A L E N D U R A N C E.

HEAVY DUTY
C-FACE MOTOR
ADAPTER:

Increases
Performance
Increases
Longevity




Simplifies
Maintenance

STACK
UP!

Competition

Increases
Longevity

Magnetic
Drain Plug

YES

No

INPRO
Lab Seals

YES

No

Epoxy Coated
Interior

YES

No

Clean Room
Assembly

YES

No

30000
lbs

20000
lbs

65000
lbs

60000
lbs

Simplifies
Maintenance

811 L. The 811 is offered in a larger frame that is ideal

in high-load applications or when conditions push the
power frame beyond ANSI limits. The 811 L features an
oversized rotating assembly and higher radial and thrust
load carrying bearings. Duplex angular contact bearings
insure zero end play for improved sealing and maximum
mechanical seal life. Whether pumping viscous liquids
or high specific gravity liquids, fluctuating process conditions, or pumping high heads or low flows, our 811 L
power frame guarantees maximum pump life in your
toughest applications.

C O M P A R E

pulp & paper

Increases
Performance

Griswold

POWER FRAME
UPGRADE:

C O M P A R E

GRISWOLDS
STANDARD
FEATURES

Power Frame
Standard
Feature
Comparison:

Cast Iron
Tensile
Strength
MTX, LTX &
XLTX Frames

Ductile Iron
Tensile
Strength
STX Frames

Optional C-Face Adapter.

Our C-Face motor adapter bolts directly
to the precision machined fit on the
power frame. Register fits on both
ends of the adapter lock in a standard
C-Face motor, guaranteeing both
parallel and angular alignment. This
quick, yet precision installation
minimizes time spent aligning shaft
couplings, and eliminates seal and
bearing replacements caused by
misalignment. Best of all, our C-Face
adapterslike the rest of our parts
are directly interchangeable with most
ANSI pumps!

1 1

GRISWOLD
At Griswold, our commitment
to your success extends way
beyond our top-of-the-line
products. Weve structured our
staff, systems and inventory to
deliver consistent high-level
solutions for meeting your most
critical equipment and emergency delivery needs. We pride
ourselves in providing WHAT
you need, WHEN you need it,
and the CONFIDENCE and RELIABILITY to make your job easier.

ENGINEERING &
CUSTOMER SUPPORT

Equipment Selection: Our

application engineers utilize
the latest software to identify
the optimum pump for your
application, as well as component and seal specifications.
Technical Support: Our engineering staff stands ready to
answer any questions regarding performance and repair.
Our state-of-the-art test center is available for a number
of certified performance
tests, either witnessed or nonwitnessed, and conforms to
Hydraulic Institute Standards.

Extensive

W E V E

OPTIONS

Griswold offers a broad range of options and upgrades to

tailor the 811s handling and performance to meet virtually
any fluid processing application. You can rely on our engineering staff to assist you in configuring pump size, material and components to best suit your specific plant and
processing requirements.

BASEPLATE
MOUNTING
SYSTEMS

811

other
brands

Griswold offers a complete

range of pre-engineered rigid
baseplates designed to reduce
stress and vibration as well as
extend MTBPM, thus ensuring
long-term durability. Our wide
selection of metallic and nonmetallic baseplates provides flexibility in selecting the best base
to fit your operating needs and
budget. Bases include a fully
enclosed steel coupling guard as
standard, with optional nonsparking coupling guard available.
Fabricated
Steel Base
(enhanced fabricated
steel base also
available)

HIGH & LOW

TEMPERATURE
CAPABILITY

C O M PA R E

SUPPORT

C O M PA R E

Comprehensive

SU

811
other
brands

Heat Jacket: Clamps on to the

casing to manage heat transfer. Easy to install or remove for
servicing.
Jacketed Seal Chamber:
Maintains temperature control
for heating or cooling of sealing environment.
Bearing Frame Finned Cooler:
Directly cools oil to lower
bearing temperature. Recommended for temperatures over
350 degrees.

certified
testing

Composite
Base

engineering
support

Composite
Foundation Base

1 2

PERIORSOLUTIONS
G O T

Y O U

Comprehensive
C O M PA R E

LUBRICATION
OPTIONS

SUPPORT
811

other
brands

The Griswold staff, along with

our stocking distributors, can
review your pumps and parts
usage to recommend upgrades
and optimize your on-site
inventory, minimizing stocking
hassles and your long-term
operating costs. Because we
offer identical features, interchangeability and quality as
hundreds of thousands of
pumps and parts worldwide, at
30-40% savings, we can improve
your existing process and reduce
your total cost of ownership.

SEAL FLUSH
PLANS

other
brands

We offer all ANSI B73.1 seal

flush and cooling plans to control emission levels, improve
lubrication and cooling of the
seal faces, and reduce downtime. Ask us to assist you in
selecting the best plan.

EXPEDITED
DELIVERY

36-Hour Ship Commitment

on Entire Pumps, Same-Day
Shipping on Parts:

SPECIAL SURFACE
PREPARATION
Griswold offers a variety of
optional surface preparation
processes for extended corrosion
protection and contaminantfree pumping:
Electro Polishing
Passivation
Hard Metal Coatings
Fusion Bonded, Epoxy
Coated Power End
Special Paint Systems

C O M PA R E

C O M PA R E

811 power ends accommodate

all lubrication systems, including
flood oil, oil mist and grease lubrication. Our power ends are predrilled for all lubrication methods
and can be easily converted in the
field without modification.

811

INVENTORY
OPTIMIZATION

811

other
brands

Griswold offers the quickest

delivery response in the industry.
When your production quota is
on the line, each day of downtime waiting on a repair can
mean several hundred thousand
dollars of revenue, unfulfilled
critical shipments, and lost jobs.
Factor those statistics into your
total costs of ownership! Maintaining an extensive inventory
at our headquarters and stocking distributors, we can make
this commitmentor better
without the additional premiums our competitors charge.

3 6-H O U R S H I P P I N G C O M M I T M E N T !
(SAME

D AY

ON

PARTS)
P

1 3

PERFORMANCE &
capacity 2850 RPM (50Hz)
3/
h

20

40

0 GPM 100

180

400

140

500

160

600

180

700

200

800

220

900

240

1000

260

280

1100

1200

300
1300

Ft.
210

600

180

800

500

160

400

120

700

LF 3x1 13
1/
2

600

3x11/2 13

400

LF 11/2 x1 8

200

300
80

2x
110
200

3x

11/2 x1 8 11/2 3x28

40

3/ 20
h

4x38G

3x11/2
6

0 GPM 100

6x4 10G

4x313

4x310

3x210

11/2 x1
6

100

3x213

3x11/2 10

300

20

1750
1450
RPM
PERFORMANCE
CURVE

120

700

500

60

300

100

900

140

100

200

80

Ft.
1000

LF 2x110

300
280
260
240
220

60

100

3x26

200

300

40

60

400

80

500

100

600

120

700

140

800

160

180

900

200

1000

220

1100

240

1200

260

1300

1400

300

320

280

1500

340

1600

360

capacity 3500 RPM (60Hz)

capacity 1450 RPM (50Hz)

3/
h

20

Ft. 0 GPM
240

40

100

60

200

100
300

150

400

600

200
800

300
1000 1200

400

500

1600

2000

2400

Ft.
160

70
210

180

50
45

120
35

150

100

120

LF 2x1 10

30

40

10x815G

40
35

140

8x615

100

3x11/2 13

LF 11/2 x1 8

40

8x613

80

25

20

2x
110

60

3x11/2
10

60

6x413

10x8 13

80
20

4x313

3x213

30

3x210

4x310

6x4 10H
6x4 10G

1 x1 8
1/
2

3x1
8

1/
2

H
10
3
4x

4x3 8

3x28

40
10

4x38G

11/2 x1 3x11/2
6
6

20

0
0 GPM
0

1 4

20

3x26

3/
h

100
20

200
40

50

300
75

400
100

600
150

800
200

1000

1200
250

300

capacity 1750 RPM (60Hz)

1600
400

2000

2400
500

2800
600

3200
700

3600
800

total head 1450 RPM (50Hz)

total head 1750 RPM (60Hz)

60
55

45

LF 3x11/2 13

65

10

total head 2850 RPM (50Hz)

total head 3500 RPM (60Hz)

3500
2850
RPM
PERFORMANCE
CURVE

CONSTRUCTION DETAILS
constructiondetails
Griswold811 Model

Model 811 S

Model 811 M

Model 811 L

Volute

Model 811 XL

single

Nominal Case Thickness (in.)

Corrosive Allowance @ Max.

3/8

1/2 (6x413A80 = 5/8)

1/8

Working Pressure
Max. Working PSIG

Limits set by ANSI B16.5

See Pressure/Temp. charts on following page

Hydro Test PSIG @ 100F

Max. Liquid Temp. (F)
At Coupling (in.)

Shaft
Diameter

Sleeve Dia. Under Seal (in.)

Under Impeller (in.)
Under Sleeve (in.)
Overhang (in.)
Radial

Bearings

Thrust
Bearing Span
Mechanical Seal Size (in.)
Stuffing Box I.D. (in.)
Standard Bore Depth (in.)
Distance End of Box
to Nearest Obstruction

Stuffing Box I.D. (in.)

Large Bore

Depth (in.)

Distance End of Box

to Nearest Obstruction
Lantern Ring Width (in.)

9/16

150% of working pressure at 100F (38C)

350F without Cooling / 500F with Cooling
1 1/8
1 7/8

7/8

2 3/8

1 3/8
3/4

1 3/4
1

2 1/8
1 1/4

2 1/2
1 1/2

1 1/8
6 1/8
SKF 6207

1 1/2
8 3/8
SKF 6309

1 7/8
8 3/8
SKF 6311

2
9 31/32
SKF 6313

SKF 5306 A/C3

4 1/8
1 3/8
2
2 1/8

SKF 5309 A/C3

6 3/4
1 3/4
2 1/2

SKF 7310 BECBM

6 7/8
2 1/8
2 7/8
2 5/8

SKF 5313 A/C3

9 1/4
2 1/2
3 3/8
3

2 13/16

2 15/16

2 1/2
2 7/8
2 1/8

3 1/2
2 5/8

3 7/8

4 1/2
3

2 3/16

2 13/16

2.85

7/16

5/8

5/8

component interchangeability
shaft & bearing frame

adapter

stuffing box

impeller

casing

casing size
11/2 x 16
3 x 11/2 6
3 x 26
LF 11/2 x 1 8
11/2 x 1 8
3 x 11/2 8
3 x 2 8
4 x 3 8
4 x 3 8G
LF2 x 110
2 x 110
3 x 11/2 10
3 x 210
4 x 310
6 x 410G
6 x 410H
3 x 11/2 13
3 x 213
4 x 313
6 x 413
LF2 x 110
2 x 110
3 x 11/2 10
3 x 210
4 x 310
6 x 410G
6 x 410H
LF 3 x 11/2 13
3 x 11/2 13
3 x 213
4 x 313
6 x 413
8 x 613
10 x 813
8 x 615
10 x 815
10 x 815G

Model 811S

1 3/8: shaft diameter

max. BHP-40 HP

Model 811M

1 3/4: shaft diameter

max. BHP-122 HP

Model 811L

2 1/8: shaft diameter

max. BHP-200 HP

Model 811XL

2 1/2: shaft diameter

max. BHP-249 HP
P

1 5

PARTS,MATERIAL
partslist key

100
184
126
333A

250

108
360
122

101

112

496A

134

370

332A

136

107

228
496

319

355
353

241

105

469B
168

351
418

1 6

106

358A

& MISC. SPECIFICATIONS

ITEM REQ'D
NO.
PER
PUMP

PART
NAME

ALL
DUCTILE
IRON

ALL
316SS

ALL
ALLOY
20

ALL
ALL
CD4MCu MONEL

HASTELLOY
B&C

100

Casing

DI

316SS

Alloy 20

CD4MCu

Monel

B&C

101

Impeller

DI

316SS

Alloy 20

CD4MCu

Monel

B&C

105

Lantern Ring

106

Packing

107

Packing Gland

Monel

B&C

108

Frame Adapter

112

Outboard (Thrust) Bearing

122

Shaft - Less Sleeve (Optional)

122

Shaft - With Sleeve

126

Shaft Sleeve

134

Bearing Housing

136

Lock Nut / Lock Washer

Steel

168

Inboard (Radial) Bearing

Single Row Deep Groove

184

Stuffing Box

228

Frame

241

Frame Foot

250

Gland

319

Sight Oil Gauge

332A

Labyrinth Oil Seal (Outboard)

Bronze (Optional Carbon Filled Teflon)

333A

Labyrinth Oil Seal (Inboard)

Bronze (Optional Carbon Filled Teflon)

351

Casing Gasket

353

Gland Stud

355

Gland Nut

304SS

357K

Hex Nut

304SS

358A

Casing Drain Plug (Optional)

360

Gasket, Frame-to-Adapter

360A

Gasket, Bearing End Cover

370

Brg. Hsg.Hex Bolt

Steel

418

Cas. Jack Screw

Steel

parts&
material

composition

Glass Filled TFE

SIL C-8201 Acid Rest.

TFE

316SS

Alloy 20
Ductile Iron

Double Row Angular Contact**

316SS
SAE4140

316SS

316SS

Alloy 20

Monel

B&C

Monel

B&C

Cast Iron

DI

316SS

Alloy 20

CD4MCu

Cast Iron (Ductile for Small Frame)

Cast Iron
316SS

Alloy 20
Cad. Plated

Aramid Fiber with EPDM Rubber

316SS

Steel

316SS

Alloy 20

316SS

Monel

Hastelloy

Vellumoid
Vellumoid (811XL Only)

469B

Dowel Pin

496

Brg. Hsg. O-Ring

Buna Rubber

Steel

496A

Impeller O-Ring

Glass Filled TFE

** 811L Power End features Duplex Angular Contact

pressure&
temperature

HASTELLOY B & C
DUCTILE
316

250

MINIMUM TEMPERATURE DUCTILE IRON ONLY

max. case working pressure PSIG

300

200
150
100
50
0
-400

-300

-200

W-20
MONEL

400
350

DUCTILE IRON, TYPE 316, W-20, MONEL, NICKEL, HASTELLOY B & C

NICKEL

200
100
0
-400

-300

-200

capability

DUCTILE IRON ONLY

Maximum Working Pressure Limits

models 811S, 811M, 811L; Class 150 Flanges

MINIMUM TEMPERATURE

max. case working pressure PSIG

Maximum Working Pressure Limits

models 811S, 811M, 811L; Class 300 Flanges

-100
0
100 200 300 400
temperaturedegrees fahrenheit

500

600

NICKEL

-100
0
100 200 300 400
temperaturedegrees fahrenheit

500

600

Note: Final selections must be based on

temperature and pressure limits
given in general data section.

1 7

ROTATION

DIMENSIONAL,B

PUMP END DIMENSIONS

small
PUMP END
BASEPLATE&

SMALL

Pump
Size

ANSI

Discharge

Designation

1 1/2 x 1 - 6
3 x 1 1/2 - 6
3x2-6
1 1/2 x 1 - 8
LF 1 1/2 x 1 - 8
3 x 1 1/2 - 8

AA
AB
AC
AA
AA
AB

Suction

CP

1
1 1/2
5 1/4 6 1/2 17 1/2
1 1/2
3
5 1/4 6 1/2 17 1/2
2
3
5 1/4 6 1/2 17 1/2
1
1 1/2
5 1/4 6 1/2 17 1/2
1
1 1/2
5 1/4 6 1/2 17 1/2
1 1/2
3
5 1/4 6 1/2 17 1/2
BASEPLATE DIMENSIONS

E1

E2

3
3
3
3
3
3

0
0
0
0
0
0

7 1/4
7 1/4
7 1/4
7 1/4
7 1/4
7 1/4

Impeller Max.Diam
Eye (sq in) Solids

3.1
7.1
6.5
3.5
3.1
4.4

11/32
7/16
3/8
11/32
3/16
7/16

Max
NEMA
Frame

Baseplate
number

HA**

HB

HT Min

HD

HE

HF

HG Max

HH

HL

HP

184T
256T
326TS

139
148
153

12/15
15/18
18/21

39
48
53

3.5
3.5
3.5

9
10.5
12.88

4.5
6
7.5

36.5
45.5
50.5

3.75
4.13
4.75

0.75
0.75
0.75

4.5
4.5
4.5

1 1/4
1 1/4
1 1/4

PUMP END DIMENSIONS

MEDIUM

medium
& large
PUMP END
BASEPLATE&

MEDIUM
OR

LARGE
(LF 3 x1-1/2 -13
available with large
frame only)

1 8

Pump
Size

ANSI

Discharge Suction

Designation

3x2-8
4x3-8
4 x 3 - 8G
2 x 1 - 10
LF 2 x 1 - 10
3 x 1-1/2 - 10
3 x 2 - 10
4 x 3 - 10
6 x 4 - 10G
6 x 4 - 10H
3 x 1-1/2 - 13
LF 3 x1-1/2 - 13
3 x 2 - 13
4 x 3 - 13
6 x 4 - 13

A60
A70
A70
A05
A05
A50
A60
A70
A80
A80
A20
A20
A30
A40
A80

CP

2
3
8 1/4 9 1/2 23 1/2
3
4
8 1/4
11
23 1/2
3
4
8 1/4
11
23 1/2
1
2
8 1/4 8 1/2 23 1/2
1
2
8 1/4 8 1/2 23 1/2
1 1/2
3
8 1/4 8 1/2 23 1/2
2
3
8 1/4 9 1/2 23 1/2
3
4
8 1/4
11
23 1/2
4
6
10
13 1/2 23 1/2
4
6
10
13 1/2 23 1/2
1 1/2
3
10
10 1/2 23 1/2
1 1/2
3
10
10 1/2 23 1/2
2
3
10
11 1/2 23 1/2
3
4
10
12 1/2 23 1/2
4
6
10
13 1/2 23 1/2
BASEPLATE DIMENSIONS

E1

E2

4 7/8
4 7/8
4 7/8
4 7/8
4 7/8
4 7/8
4 7/8
4 7/8
4 7/8
4 7/8
4 7/8
4 7/8
4 7/8
4 7/8
4 7/8

3 5/8
3 5/8
3 5/8
3 5/8
3 5/8
3 5/8
3 5/8
3 5/8
3 5/8
3 5/8
3 5/8
3 5/8
3 5/8
3 5/8
3 5/8

12 1/2
12 1/2
12 1/2
12 1/2
12 1/2
12 1/2
12 1/2
12 1/2
12 1/2
12 1/2
12 1/2
12 1/2
12 1/2
12 1/2
12 1/2

Impeller Max.Diam
Eye (sq in) Solids

5.4
12.5
11.0
4.9
4.9
6.5
3.1
12.5
25.9
27.1
4.9
8.3
3.1
14.2
28.0

1/2
1 1/8
11/16
7/16
3/16
7/32
3/8
5/8
1
1
7/32
7/16
3/8
5/8
1

Max
NEMA
Frame

Baseplate
number

HA**

HB

HT Min

If pump
D = 8.25
HD

If pump
D = 10
HD

HE

HF

HG Max

HH

HL

HP

184T
215T
286T
365T
405TS
449TS

245
252
258
264
268
280

12/15
15/18
18/21
18/21
24/26
24/26

45
52
58
64
68
80

3.5
3.5
3.5
3.5
3.5
3.5

12
12.38
13
13.88
14.88
15.88

13.75
14.13
14.75
14.75
14.88
15.88

4.5
6
7.5
7.5
9.5
9.5

42.5
49.5
55.5
61.5
65.5
77.5

3.75
4.13
4.75
4.75
4.75
4.75

0.75
0.75
1
1
1
1

4.5
4.5
4.5
4.5
4.5
4.5

1 1/4
1 1/4
1 1/4
1 1/4
1 1/4
1 1/4

* Flange drilling is standard ANSI 150 lb, flat face. All LF pumps use 150 lb raised face flanges, except the LF 3 x1-1/2 - 13,
which uses 300 lb raised face flanges.
** HA dimensions represent Griswolds standard construction/ANSI maximum width, respectively.

HP & CASTING DATA

RO

TA
T IO

x-large

PUMP END
BASEPLATE&

PUMP END DIMENSIONS

X-LARGE

Pump
Size

ANSI
Designation

8 x 6 - 13
10 x 8 - 13
8 x 6 - 15
10 x 8 - 15
10 x 8 - 15G

A90
A100
A110
A120
A120

Discharge Suction

6
8
6
8
8

8
10
8
10
10

CP

E1

E2

14 1/2
14 1/2
14 1/2
14 1/2
14 1/2

16
18
18
19
19

33 7/8
33 7/8
33 7/8
33 7/8
33 7/8

8
8
8
8
8

4.5
4.5
4.5
4.5
4.5

18 3/4
18 3/4
18 3/4
18 3/4
18 3/4

Impeller Max.Diam
Eye (sq in) Solids

45.5
56.7
50.0
74.6
63.0

11/16
1
13/16
1 1/8
1 1/8

BASEPLATE DIMENSIONS
Max
NEMA
Frame

Baseplate
number

HA**

HB

HT Min

HD

HE

HF

HG Max

HH

HL

HP

286T
405T
449T

368
380
398

24/26
24/26
24/26

68
80
98

5
5
5

19.25
19.25
19.25

9.5
9.5
9.5

65.5
77.5
95.5

4.75
4.75
4.75

1
1
1

6.5
6.5
6.5

1 1/4
1 1/4
1 1/4

* Flange drilling is standard ANSI 150 lb, flat face.

** HA dimensions represent Griswolds standard construction/ANSI maximum width, respectively.

tapped openings(NPT)
NUMBER
OF TAPS

811S

Lantern Ring Connection*

1/4

Frame Adapter Drain*

PURPOSE

TAP SIZE
811M
811L

811XL

3/8

3/8

3/8

SLOT

SLOT

SLOT
RTF

Casing Drain**

3/8

3/8

3/8

Alternate Casing Drain

1/2

1/2

1/2

1/2

Bearing Frame Cooling*

1/2 & 1

1/2 & 1

1/2 & 1

1/2 & 1

Discharge Gage Connection**

1/4

3/8

3/8

3/8

Suction Gage Connection

1/4

3/8

3/8

3/8

Stuffing Box Circulating Line**

1/4

3/8

3/8

3/8

Quench Gland Connection*

1/4

1/4

1/4

1/4

* Indicates items furnished standard.

** Standard in Ductile Iron and Stainless Steel; optional in other materials.

materials /casting specs

DASH

MATERIAL

-N6

Ductile Iron

ASTM A395

-91

316SS

ASTM A296 Gr. CF8M

B.H.P. limits
R.P.M.

811S

MODEL
811M
811L

3560

40.0

122.0

200.0

2900

32.7

99.5

165.0

1780

20.0

61.0

100.0

249.0

1450

16.3

49.7

81.5

203.0

1180

13.3

40.5

66.4

165.0

880

9.9

30.2

49.5

123.0

811XL

CASTING SPECIFICATION

-20

Alloy 20

ASTM A296 Gr. CN7M

-X4

CD4MCu

ASTM A31 Gr. CD4MCu

1 9

GRISWOLD PUMP COMPANY

107 Plantation Oak Drive
Thomasville, GA 31792

GRISWOLD

phone
toll free
fax
toll free fax

229-226-5255
800-843-9222
229-226-5567
800-752-2929

email
Griswold@GriswoldPump.com
website www.GriswoldPump.com

(3/ 06)