Depth of Investigation

SHORT NOTE ON
THE DEPTH OF INVESTIGATION

OF ELECTRICAL METHODS
PARAMETERS CONTROLLING THE DEPTH OF INVESTIGATION

DEPTH OF INVESTIGATION OF VERTICAL ELECTRICAL SOUNDING
DEPTH OF INVESTIGATION OF MULTI-ELECTRODE RESISTIVITY IMAGING
DEPTH OF INVESTIGATION OF MULTI-ELECTRODE RESISTIVITY IMAGING
WITH ROLL ALONG EXTENSIONS
www. iris-instruments.com
iris@iris-instruments.com
J. BERNARD, July 2003
Voltage VAB
Intensity IAB
TX
RX
Voltage VMN
ground resistance, resulting from

several layers with different resistivities
APPARENT RESISTIVITY = (coefficient) x voltage / intensity = Rho = K x VMN / IAB

K = 2 x Pi / ( 1/AM 1/AN 1/BM + 1/BN )
with Rho in ohm.m, K in m, VMN in mV, IAB in mA
In the transmitting circuit: IAB = VAB / RAB, with VAB in V, RAB in kohm, IAB in mA
SCHLUMBERGER SOUNDING AND PROFILING
WENNER SOUNDING AND PROFILING
DIPOLE DIPOLE ARRAY
MAIN
ELECTRODE
ARRAYS
POLE DIPOLE ARRAY
POLE POLE ARRAY
Fig 1: PRINCIPLES OF ELECTRICAL METHODS
DEPTH OF INVESTIGATION OF ELECTRICAL METHODS

PRINCIPLE OF ELECTRICAL METHODS (Fig 1)
In electrical methods, a current IAB is transmitted into the ground with two electrodes (A, B), while the
difference of potential VMN produced by the circulation of this current into the geological layers is
measured with two other electrodes (M, N). The -apparent- resistivity rho of the ground is defined by
the relation rho = K x VMN / IAB, where K is a geometrical coefficient which depends on the separations
between the A, B, M, N electrodes: K = 2 / (AM-1 AN-1 BM-1 + BN-1).
PARAMETERS CONTROLLING THE DEPTH OF INVESTIGATION

On a theoretical point of view, the depth of investigation of a measurement depends on the length of
the transmitting line AB and on the separation between the transmitting AB line and the receiving MN
line. Various types of electrode combinations can be used (Schlumberger, Wenner, dipole, pole,
gradient arrays, ), each of them featuring various benefits and limitations in terms of vertical
penetration, lateral resolutions, field set-up, but all following the same general rules:
o
the larger the length AB, the deeper the penetration of the current
the farther the M, N receiving electrodes from the A, B transmitting electrodes, the
more representative the potential measured on the surface of the ground, of the
resistivity of deep layers.
The arrays can be used on a sounding procedure where the depth of investigation is increased at
each new reading for a given midpoint, or in a profiling procedure where the spacings between the
electrodes is kept constant for all readings, the midpoint of the array being moved of an elementary
distance at each new reading. In the profiling procedure, the depth of investigation of the readings is
determined by the spacings between the electrodes.
On a practical point of view, the depth on investigation also depends on the measurability of the VMN
potential which can be expressed as VMN = rho x IAB / K. For large investigation depths, the electrodes
have to be far away from each other, the K coefficient has thus an important value, and the VMN signal
becomes small, possibly difficult to measure. Several factors facilitate a good measurement at large
investigation depths:
o
a high ground resistivity rho: a 1000 ohm.m ground (hard rock) produces a VMN
signal ten times greater than a 100 ohm.m ground (sedimentary rock) and a hundred
times greater than a 10 ohm.m ground (clayey formation). The resistivity parameter,
linked to the nature of the rocks, is of course out of the control of the operator
a high intensity of the current IAB = VAB / RAB, which means:
a low ground resistance RAB: if the surface layer is a dry sand (which
has a very high resistivity), the ground resistance of the A and B
electrodes are higher than if it is a clayey soil (which has a very low
resistivity). However, it is possible to decrease a ground resistance
RAB by using several long stakes at each A and B transmitting points,
poured with salt water for instance, which decreases the resistivity of
the ground located near to these transmitting points, thus the ground
resistance RAB.
and/or a high output voltage VAB, obtained with a powerful equipment.

The resistivity systems are usually characterized by a maximum
current, a maximum voltage and a maximum power, one of these
three parameters determining the intensity of the current which can
really be transmitted into the ground, in relation with the value of the
ground resistance RAB.
a highly sensitive meter, with filtering capability including stacking / averaging process
for noise rejection (Self Potential, drift of SP, power lines fields, other industrial or
natural electromagnetic interferences,), which makes it possible to measure a low
VMN amplitude in an as-short-as-possible acquisition time.
FIRST LAYER
Resistivity : Rho1
Thickness : E1
SECOND LAYER
Resistivity : Rho2
apparent
resistivity
XR
Rho1
Rho2
XC
AB / 2
E1
In case of a two layer sounding, when the second layer is more resistive than the first one, its presence is
observed in the apparent resistivity curve for a length of line AB/2 longer than when the second layer is more
conductive. In the figure, XR is longer than XC, for the same relative variation of the apparent resistivity curve.
Apparent resistivity (ohm.m)
Fig 2: TWO LAYER MASTER CURVES FOR SCHLUMBERGER 1D SOUNDINDS
alluviums
limestone
EXAMPLE OF INTERPRETATION OF
A 1D SCHLUMBERGER SOUNDING
clay
AB/2 (m)
102
DEPTH OF INVESTIGATION OF VERTICAL ELECTRICAL SOUNDING (VES) (Fig 2)

In the VES technique, the ground is supposed to be composed of horizontal layers. It is a common
rule of thumb to say that the depth of investigation is of the order of 0.1 to 0.3 times the AB length: a
1km AB line leads to a depth of 100 to 300m, depending on the type of layering (for instance, a
conductive basement can be seen with a shorter AB line than a resistive one; however, the signal is
normally lower in the first case than in the second one).
In a traditional Sclumberger or Wenner electrical sounding, the transmitting A and B electrodes are
successively moved away from each other at each new reading to increase the depth of investigation.
The operator fully controls the AB and MN lengths, as the four electrodes and their wires are
independent. As the time necessary to move from one position to the next one becomes longer and
longer for deep investigations, it is reasonable in these soundings to spend a significant time to stack
the signal so as to improve the quality of the reading or to make this reading possible.
DEPTH OF INVESTIGATION OF MULTI-ELECTRODE RESISTIVITY IMAGING (Fig 3)

Recently, a new concept of equipment has been introduced to make it possible the acquisition of
many readings in a reduced amount of time for environmental applications corresponding to rather
shallow investigations depths, of the order of 10 to 50m. The technique is sometimes called Electrical
Resistivity Imaging (ERT).
The concept consists in using multi-core cables which contain as many individual wires as number of
electrodes, with one take-out every 5m, 10m, and 24, 48, 72, 96, electrodes. The measuring unit
includes relays which automatically carry out the sequences of readings introduced in its internal
memory. The aim of this set-up is to take readings for many combinations of transmission and
reception pairs, so as to achieve some kind of mixed profiling / sounding array. In such a way of
proceeding, the total length of cable is the product of the electrode spacing by the number of
electrodes: 240m for 48 electrodes at 5m spacing, which determines the maximum depth of
investigation, on contrary to the classical VES technique where it is always possible to add new reels
of wire to increase the separation between the A and B transmitting electrodes.
For Schlumberger, Wenner and Dipole - Dipole types of electrode arrays, the maximum depth of
investigation is of the order of 0.2 times the total length of cables, for instance 50m for 48 electrodes
spaced at 5m (total length: 240m). For Pole Pole arrays where one electrode of current and one
electrode of potential are placed far from the measuring line, the depth of investigation is increased to
0.9 times the length of the multi-core cable (220m in the previous example). See Dr Lokes Tutorial on
2D & 3D electrical imaging surveys at geoelectrical.com for more details.
For these multi-electrodes profiles, the number of readings which are taken for a given spread of line
is quite high compared to the traditional four electrode soundings (easily a few hundreds readings). It
is the reason why the acquisition time for one reading (which is repeated so many times to obtain the
full image) is quite determinant for the efficiency of the survey, and the highest the power of the
equipment, the lowest the duration of the field work.
DEPTH OF INVESTIGATION OF MULTI-ELECTRODE RESISTIVITY IMAGING WITH

ROLL ALONG EXTENSIONS
The maximum depths here above mentioned are obtained when the electrodes located at the
extremity of the line are addressed. This corresponds to one only point which is the middle point of the
array. When the line to prospect is longer than the length of the multi-core cable, a roll along
procedure is usually used where the first segment of the multi-core cable is moved to the extremity of
the cable to enable further readings.
For instance, if a 48 electrode 240m long initial line consists in two segments of 120m with 24
electrodes spaced at 5m for each segment, the minimum displacement consists in one segment of
120m. This makes that the continuity of the image will be only ensured for half the maximum depth of
the array as reported in the previous paragraph (see figure 3 for visual understanding).
station
1
segment a
AREA INVESTIGATED
with one set of readings of a multi-electrode
sequence. The equipment is placed in the middle
(station 1) of the multi-core cable composed of
two segments, a and b.
segment b
The maximum depth reached, referred to as

Max, depends on the electrode arrays used.
For Wenner and dipole dipole arrays, this Max
depth is estimated to 0.2 L, L being the total
length of the cable (segment a + segment b)
Max
station
1
segment a
station
2
In case of a roll along procedure with a

two segment cable (a and b), a first
sequence of readings is taken with the
equipment located in station 1, using the
segments a and b.
Then, a second sequence is taken with
the equipment moved to station 2, using
the segments b and a.
segment b
segment b
segment a
1/2 Max
The maximum depth reached which

ensures a continuity of the bottom part of
the image is 1/2 Max
station
1
segment a
station
2
segment b segment c
In case of a roll along procedure with a

four segment cable (a, b, c and d), a first
sequence of readings is taken with the
equipment located in station 1, in the
middle of the segments a, b, c and d.
Then, a second sequence is taken with
the equipment moved to station 2, in the
middle of the segments b, c, d and a.
segment d
segment b segment c segment d segment a
3/4 Max
The maximum depth reached which

ensures a continuity of the bottom part of
the image is 3/4 Max
number of
electrodes
48
72
electrode
spacing
Total line
Max depth
length L for a sequence
(about 0.2 L)
number of
segments
Max depth in roll along sequences (one

segment translation) ensuring a continuity
of the bottom part of the image
5m
240m
48m
1/2 Max = 24m
10m
480m
96m
3/4 Max = 64m
5m
360m
72m
3/4 Max = 48m
10m
720m
144m
5/6 Max = 128m
Fig 3: EXAMPLES OF MAXIMUM DEPTHS OF INVESTIGATION OBTAINED WITH A MULTI-ELECTRODE SYSTEM,

FOR A WENNER OR A DIPOLE DIPOLE ARRAY
As another example, one can consider the case of a 72 electrode 360m long initial line consisting in
four segments of 90m of 18 electrodes each spaced at 5m, the roll along can be made by moving one
segment of 90m, which makes that the maximum depth which will ensure a continuity of the image is
the three fourths of the maximum depth mentioned earlier.
More generally, when a cable is composed of n segments, the maximum depth enabling a continuity
of the bottom line of the image during roll along sequences with a unitary translation of 1 segment for
each new sequence is equal to (n-1)/n times the maximum depth obtained with the initial sequence.
The table of figure 3 summarizes some numerical applications of this rule for various usual types of
cables and number of electrodes.
CONCLUSIONS
It must be pointed out that the depth of investigation in electrical methods depends on two main
factors: on the one hand the geometry of the cables (type of array, number of electrodes, spacing
between electrodes, number of segments); on the second hand on the measurability of the signal by
the equipment, namely the amplitudes of the signal and of the existing noise, the power specifications
of the equipment and its ability of filtering the noise through the stacking process.
SYSCAL Junior
SYSCAL R1 Plus
SYSCAL Pro
1 channel
SYSCAL Pro
10 channels
Max voltage & power
400V, 100W
600V, 200W
800V, 250W
800V, 250W
Max current at 2.5kohm
160mA
240mA
320mA
320mA
for 1000 ohm.m

ground resistivity
100mV
3 stacks, 20 mn
150mV
3 stacks, 20mn
200mV
3 stacks, 20mn
200mV
3 stacks, 2mn
for 100 ohm.m

ground resistivity
10mV
6 stacks, 30mn
15mV
5 stacks, 25mn
20mV
3 stacks, 20mn
20mV
3 stacks, 2mn
for 10 ohm.m
ground resistivity
1mV
40 stacks, 1h40mn
1.5mV
30 stacks, 1h20mn
2mV
20 stacks, 1h
2mV
20 stacks, 6mn
Average measured
signal in the section
Equipment
Fig 4: TABLE GIVING AN ESTIMATE OF THE AMPLITUDE OF THE SIGNAL MEASURED IN A RESISTIVTY
IMAGING SECTION, IN RELATION WITH THE MAXIMUM OUTPUT VOLTAGE OF THE EQUIPMENT
The values of the apparent resistivity of the ground are 1000, 100, and 10ohm.m
The ground resistance of the electrodes is supposed to be 2.5kohm.
The measured signal is computed as a rough average of a Pole Dipole array in a roll along sequence,
with 48 electrode system at 5m spacing, for a total of 500 readings.
The number of stacks n is related to a 1% quality of reading, for a standard noise, with 250ms pulses
The duration of the survey expressed in h-mn is given as an indication, for comparison purposes. In practise,
the duration depends on the local noise (SP and EM effects, ) and on the quality of the readings required.
clay layer
landfill with conductive lixivia and organic material
clay layer
resistivity (ohm.m)
Example of interpretation of
a 2D Resistivity section
Multinode unit
SYSCAL Junior resistivity meter
GEOPHYSICAL
INSTRUMENTS
FOR
ELECTRICAL
PROSPECTING
Switch unit
SYSCAL Kid Switch 24 imaging resistivity system
SYSCAL Pro Switch 48 imaging resistivity system
SYSCAL R2
resistivity meter
SYSCAL R1 Plus Switch 48

imaging resistivity system
SYSCAL R1 Plus resistivity meter

Depth of Investigation

Uploaded by

Copyright:

Available Formats

Depth of Investigation

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Depth of Investigation

Uploaded by

Copyright:

Available Formats

SHORT NOTE ON

THE DEPTH OF INVESTIGATION

PARAMETERS CONTROLLING THE DEPTH OF INVESTIGATION

J. BERNARD, July 2003

ground resistance, resulting from

APPARENT RESISTIVITY = (coefficient) x voltage / intensity = Rho = K x VMN / IAB

WENNER SOUNDING AND PROFILING

DIPOLE DIPOLE ARRAY

POLE DIPOLE ARRAY

POLE POLE ARRAY

Fig 1: PRINCIPLES OF ELECTRICAL METHODS

DEPTH OF INVESTIGATION OF ELECTRICAL METHODS

PARAMETERS CONTROLLING THE DEPTH OF INVESTIGATION

a high intensity of the current IAB = VAB / RAB, which means:

and/or a high output voltage VAB, obtained with a powerful equipment.

Apparent resistivity (ohm.m)

Fig 2: TWO LAYER MASTER CURVES FOR SCHLUMBERGER 1D SOUNDINDS

DEPTH OF INVESTIGATION OF VERTICAL ELECTRICAL SOUNDING (VES) (Fig 2)

DEPTH OF INVESTIGATION OF MULTI-ELECTRODE RESISTIVITY IMAGING (Fig 3)

DEPTH OF INVESTIGATION OF MULTI-ELECTRODE RESISTIVITY IMAGING WITH

The maximum depth reached, referred to as

In case of a roll along procedure with a

The maximum depth reached which

In case of a roll along procedure with a

segment b segment c segment d segment a

The maximum depth reached which

Max depth in roll along sequences (one

1/2 Max = 24m

3/4 Max = 64m

3/4 Max = 48m

5/6 Max = 128m

Fig 3: EXAMPLES OF MAXIMUM DEPTHS OF INVESTIGATION OBTAINED WITH A MULTI-ELECTRODE SYSTEM,

Max voltage & power

Max current at 2.5kohm

for 1000 ohm.m

for 100 ohm.m

landfill with conductive lixivia and organic material

SYSCAL Junior resistivity meter

SYSCAL Kid Switch 24 imaging resistivity system

SYSCAL Pro Switch 48 imaging resistivity system

SYSCAL R1 Plus Switch 48

SYSCAL R1 Plus resistivity meter

You might also like