FLIR P60 Manual PDF

ThermaCAM P60
Operators manual
Publ. No.
Revision
Language
Issue date
1 557 945
a43
English (EN)
April 6, 2004
ThermaCAM P60
Operators manual
Publ. No. 1 557 945 Rev. a43 ENGLISH (EN) April 6, 2004
Legal disclaimer
All products manufactured by FLIR Systems are warranted against defective materials and workmanship for a period of one (1) year from the
delivery date of the original purchase, provided such products have been under normal storage, use and service, and in accordance with FLIR
Systems instruction.
All products not manufactured by FLIR Systems included in systems delivered by FLIR Systems to the original purchaser carry the warranty,
if any, of the particular supplier only and FLIR Systems has no responsibility whatsoever for such products.
The warranty extends only to the original purchaser and is not transferable. It is not applicable to any product which has been subjected to
misuse, neglect, accident or abnormal conditions of operation. Expendable parts are excluded from the warranty.
In the case of a defect in a product covered by this warranty the product must not be further used in order to prevent additional damage.
The purchaser shall promptly report any defect to FLIR Systems or this warranty will not apply.
FLIR Systems will, at its option, repair or replace any such defective product free of charge if, upon inspection, it proves to be defective in
material or workmanship and provided that it is returned to FLIR Systems within the said one-year period.
FLIR Systems has no other obligation or liability for defects than those set forth above.
No other warranty is expressed or implied. FLIR Systems specifically disclaims the implied warranties of merchantability and fitness for a
particular purpose.
FLIR Systems shall not be liable for any direct, indirect, special, incidental or consequential loss or damage, whether based on contract, tort
or any other legal theory.
Copyright
FLIR Systems, 2004. All rights reserved worldwide. No parts of the software including source code may be reproduced, transmitted, transcribed
or translated into any language or computer language in any form or by any means, electronic, magnetic, optical, manual or otherwise,
without the prior written permission of FLIR Systems.
This manual must not, in whole or part, be copied, photocopied, reproduced, translated or transmitted to any electronic medium or machine
readable form without prior consent, in writing, from FLIR Systems.
Names and marks appearing on the products herein are either registered trademarks or trademarks of FLIR Systems and/or its subsidiaries.
All other trademarks, trade names or company names referenced herein are used for identification only and are the property of their respective
owners.
Quality assurance
The Quality Management System under which these products are developed and manufactured has been certified in accordance with the
ISO 9001 standard.
FLIR Systems is committed to a policy of continuous development; therefore we reserve the right to make changes and improvements on
any of the products described in this manual without prior notice.
Patents
This product is protected by patents, design patents, patents pending, or design patents pending.
Swedish Pat. No. 518 836; PCT Pat. Pend. No. PCT/SE00/00739; US Pat. Pend. No. 09/576266; EPC Pat. Pend. No. 00925826.0; China Pat. Pend.
No. 00809178.1; Japan Pat. Pend. No. 2000-620406; PCT Pat. Pend. No. PCT/SE01/00983; Swedish Pat. Pend. No. 0101577-5; PCT Pat. Pend.
No. PCT/SE02/00857; Swedish Pat. Pend. No. 0200629-4; PCT Pat. Pend. No. PCT/SE03/00307; Swedish Pat. Des. Pend. No. 75530; US Pat. Des.
Pend. No. 29/166.626; US Pat. Des. Pend. No. 29/166.627; China Pat. Des. No. ZL02331553.9; China Pat. Des. Pend. No. 02331554.7; UK Pat.
Des. No. 3006596; UK Pat. Des. No. 3006597; Japan Pat. Des. Pend. No. 2002-23650; Japan Pat. Des. Pend. No. 2002-23649; Int. Pat. Des. No.
DM/061609.
ii
Postal address
FLIR Systems AB P. O. Box 3 SE-182 11 Danderyd Sweden
Telephone
+46 (0)8 753 25 00
Telefax
+46 (0)8 753 23 64
Web site
www.flirthermography.com
E-mail
sales@flir.se
Table of contents
1
Warnings & cautions ..................................................................................................................................................
Welcome! .........................................................................................................................................................................
2.1
About FLIR Systems ........................................................................................................................................
2.1.1
A few images from our facilities .............................................................................................
2.2
Comments & questions ................................................................................................................................
2
2
4
5
Packing list .....................................................................................................................................................................
System overview .........................................................................................................................................................
Connecting system components ......................................................................................................................... 12
Tutorials ...........................................................................................................................................................................
6.1
Switching on & switching off the camera ..............................................................................................
6.2
Working with images .....................................................................................................................................
6.2.1
Acquiring an image ....................................................................................................................
6.2.2
Opening an image .......................................................................................................................
6.2.3
Freezing & unfreezing an image ............................................................................................
6.2.4
Saving an image ...........................................................................................................................
6.3
Working with measurements .....................................................................................................................
6.3.1
Laying out & moving a spot .....................................................................................................
6.3.2
Laying out & moving an box ...................................................................................................
6.3.3
Laying out & moving a circle ...................................................................................................
6.3.4
Laying out & moving a line ......................................................................................................
6.3.5
Creating & changing an isotherm .........................................................................................
6.3.6
Resizing a measurement marker ...........................................................................................
6.4
Working with alarms ......................................................................................................................................
6.4.1
Setting the reference temperature .......................................................................................
6.4.2
Setting up a silent alarm ...........................................................................................................
6.4.3
Setting up an audible alarm ....................................................................................................
6.5
Changing level & span ..................................................................................................................................
6.5.1
Changing the level ......................................................................................................................
6.5.2
Changing the span ......................................................................................................................
6.6
Changing system settings ...........................................................................................................................
6.6.1
Changing the language ............................................................................................................
6.6.2
Changing the temperature unit .............................................................................................
6.6.3
Changing the date format ........................................................................................................
6.6.4
Changing the time format ........................................................................................................
6.6.5
Changing date & time ................................................................................................................
6.7
Working with the camera .............................................................................................................................
6.7.1
Mounting an additional lens ...................................................................................................
6.7.2
Focusing the camera using autofocus .................................................................................
6.7.3
Focusing the camera manually ..............................................................................................
6.7.4
Using the electronic zoom .......................................................................................................
6.7.5
Inserting & removing the battery ..........................................................................................
6.7.5.1
Inserting the battery ..........................................................................................
6.7.5.2
Removing the battery ........................................................................................
6.7.6
Removing & attaching the remote control from the camera handle .......................
14
14
14
14
14
15
15
15
15
15
16
16
17
17
17
18
19
19
20
20
20
21
21
21
21
22
22
22
22
23
23
23
23
24
24
25
iii
6.7.6.1
6.7.6.2
Removing the remote control ........................................................................ 25

Attaching the remote control ......................................................................... 25
Camera overview .........................................................................................................................................................

7.1
Camera parts .....................................................................................................................................................
7.2
Keypad buttons & functions .......................................................................................................................
7.3
Autofocus ...........................................................................................................................................................
7.4
IrDA infrared communication link ............................................................................................................
7.5
Camera status LCD .........................................................................................................................................
7.6
Laser LocatIR .....................................................................................................................................................
7.7
Visual camera ....................................................................................................................................................
27
27
33
34
35
35
37
37
Camera program ..........................................................................................................................................................

8.1
Screen objects ..................................................................................................................................................
8.1.1
Result table ....................................................................................................................................
8.1.2
Status bar ........................................................................................................................................
8.1.3
Temperature scale .......................................................................................................................
8.1.4
System messages .........................................................................................................................
8.1.4.1
Status messages ..................................................................................................
8.1.4.2
Warning messages ..............................................................................................
8.2
Menu system .....................................................................................................................................................
8.2.1
Navigating in the menu system .............................................................................................
8.2.2
File menu ........................................................................................................................................
8.2.2.1
Images .....................................................................................................................
8.2.2.2
Save ..........................................................................................................................
8.2.2.3
Copy to card ..........................................................................................................
8.2.2.4
Periodic save .........................................................................................................
8.2.2.5
Burst recording .....................................................................................................
8.2.2.6
Voice comment ....................................................................................................
8.2.2.7
Text comment ......................................................................................................
8.2.3
Analysis menu ...............................................................................................................................
8.2.3.1
Edit mode ...............................................................................................................
8.2.3.2
Add spot .................................................................................................................
8.2.3.3
Add box ...................................................................................................................
8.2.3.4
Add circle ................................................................................................................
8.2.3.5
Add line ...................................................................................................................
8.2.3.6
Add isotherm ........................................................................................................
8.2.3.7
Add diff ....................................................................................................................
8.2.3.8
Ref temp .................................................................................................................
8.2.3.9
Remove all ..............................................................................................................
8.2.3.10
Obj par .....................................................................................................................
8.2.3.11
Deactivate local par. ...........................................................................................
8.2.4
Image menu ..................................................................................................................................
8.2.4.1
Visual/IR ..................................................................................................................
8.2.4.2
Freeze/Live .............................................................................................................
8.2.4.3
Range .......................................................................................................................
8.2.4.4
Level/Span .............................................................................................................
8.2.4.5
Manual adjust / Continuous adjust ...............................................................
8.2.4.6
Palette ......................................................................................................................
8.2.4.7
Hide graphics ........................................................................................................
8.2.4.8
Add visual marker ...............................................................................................
8.2.5
Setup menu ...................................................................................................................................
8.2.5.1
Image .......................................................................................................................
8.2.5.2
Difference ...............................................................................................................
38
38
38
39
39
39
39
40
40
40
41
41
42
42
43
43
45
46
50
50
50
52
55
58
61
63
64
64
64
65
65
65
65
65
65
66
66
67
67
67
67
69
iv
8.2.5.3
8.2.5.4
8.2.5.5
8.2.5.6
8.2.5.7
8.2.5.8
8.2.5.9
8.2.5.10
8.2.5.11
8.2.5.12
8.2.5.13
9
Save ..........................................................................................................................
Alarm ........................................................................................................................
Digital video ..........................................................................................................
Power .......................................................................................................................
Status bar ................................................................................................................
Buttons ....................................................................................................................
Date/time ...............................................................................................................
Local settings ........................................................................................................
Camera info ...........................................................................................................
Profile .......................................................................................................................
Factory default .....................................................................................................
70
72
74
75
75
76
77
78
79
79
79
Electrical power system ...........................................................................................................................................

9.1
Internal battery charging .............................................................................................................................
9.2
External battery charging ............................................................................................................................
9.3
Battery safety warnings ................................................................................................................................
80
80
81
82
10 A note on LEMO connectors ................................................................................................................................... 84

10.1 How to connect & disconnect LEMO connectors ................................................................................ 84
11 Maintenance & cleaning .......................................................................................................................................... 86
11.1 Camera body, cables & accessories .......................................................................................................... 86
11.2 Lenses .................................................................................................................................................................. 86
12 Troubleshooting .......................................................................................................................................................... 87
13 Technical specifications & dimensional drawings ...................................................................................... 89
13.1 Imaging performance .................................................................................................................................... 89
13.2 Detector .............................................................................................................................................................. 89
13.3 Image presentation ........................................................................................................................................ 89
13.4 Temperature ranges ...................................................................................................................................... 90
13.5 Laser LocatIR ..................................................................................................................................................... 90
13.6 Electrical power system ................................................................................................................................ 90
13.7 Environmental specifications ..................................................................................................................... 91
13.8 Physical specifications ................................................................................................................................... 91
13.9 Interfaces & connectors ................................................................................................................................ 91
13.10 Pin configurations ........................................................................................................................................... 92
13.10.1 Headset connector ...................................................................................................................... 92
13.10.2 RS-232/USB connector ............................................................................................................... 93
13.10.3 Remote control connector ....................................................................................................... 94
13.10.4 Power connector .......................................................................................................................... 95
13.10.5 CVBS connector ............................................................................................................................ 95
13.10.6 FireWire connector ...................................................................................................................... 95
13.11 Relationship between fields of view and distance ............................................................................. 96
13.12 Basic dimensions battery charger ......................................................................................................... 99
13.13 Basic dimensions battery .......................................................................................................................... 100
13.14 Basic dimensions remote control .......................................................................................................... 101
13.15 Basic dimensions camera ......................................................................................................................... 102
13.17 Basic dimensions video lamp .................................................................................................................. 104
14 Glossary ........................................................................................................................................................................... 106
15 Thermographic measurement techniques ..................................................................................................... 110

15.1 Introduction ..................................................................................................................................................... 110
15.2 Emissivity ............................................................................................................................................................ 110
15.2.1
Finding the emissivity of an object ....................................................................................... 111
15.2.1.1
Using a thermocouple ....................................................................................... 111
15.2.1.2
Using reference emissivity ............................................................................... 111
15.3 Reflected ambient temperature ................................................................................................................ 111
16 History of infrared technology ............................................................................................................................. 112
17 Theory of thermography ......................................................................................................................................... 116
17.1 Introduction ...................................................................................................................................................... 116
17.2 The electromagnetic spectrum .................................................................................................................. 116
17.3 Blackbody radiation ....................................................................................................................................... 117
17.3.1
Plancks law .................................................................................................................................... 118
17.3.2
Wiens displacement law .......................................................................................................... 119
17.3.3
Stefan-Boltzmann's law ............................................................................................................. 121
17.3.4
Non-blackbody emitters ........................................................................................................... 122
17.4 Infrared semi-transparent materials ........................................................................................................ 124
18 The measurement formula ..................................................................................................................................... 126
19 Emissivity tables .......................................................................................................................................................... 132
19.1 References ......................................................................................................................................................... 132
19.2 Tables .................................................................................................................................................................. 132
Index .................................................................................................................................................................................. 149
vi
List of figures
Figure 2.1
Figure 2.2
Figure 2.3
Figure 2.4
Figure 2.5
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
4.1
4.2
5.1
5.2
5.3
5.4
6.1
6.2
6.3
6.4
6.5
7.1
7.2
7.3
Figure
Figure
Figure
Figure
Figure
Figure
Figure
7.4
7.5
7.6
7.7
7.8
7.9
7.10
Figure 7.11
Figure 8.1
Figure 8.2
Figure
Figure
Figure
Figure
Figure
Figure
Figure
8.3
8.4
8.5
8.6
8.7
8.8
8.9
FLIR Systems, Boston, USA, FLIR Systems, Danderyd, Sweden, and FLIR Systems,
Portland, USA. ......................................................................................................................................
LEFT: FLIR Systems Thermovision Model 661. The photo is taken on May 30th,
1969 at the distribution plant near Beckomberga, in Stockholm, Sweden. The camera
weighed approx. 25 kg (55 lb), the oscilloscope 20 kg (44 lb), the tripod 15 kg (33
lb). The operator also needed a 220 VAC generator set, and a 10 L (2.6 US gallon) jar
with liquid nitrogen. To the left of the oscilloscope the Polaroid attachment (6 kg/13
lb) can be seen. RIGHT: FLIR Systems ThermaCAM Model E2 from 2002 weight:
0.7 kg (1.54 lb), including battery. ................................................................................................
LEFT: Development of system electronics; RIGHT: Testing of an FPA detector .........
LEFT: Diamond turning machine; RIGHT: Lens polishing ..................................................
LEFT: Testing of IR cameras in the climatic chamber; RIGHT: Robot for camera testing
and calibration .....................................................................................................................................
System overview .................................................................................................................................
Explanations of callouts ....................................................................................................................
How to connect system components, 1: Rear connectors ..................................................
How to connect system components, 1: Front connectors ................................................
Mounting an additional lens ..........................................................................................................
Inserting the battery ..........................................................................................................................
Removing the battery .......................................................................................................................
Removing the remote control ........................................................................................................
Attaching the remote control ........................................................................................................
Camera parts, 1 ....................................................................................................................................
Camera parts, 2 ....................................................................................................................................
Video lamp, to be inserted in the RS-232/USB connector. The video lamp will
automatically be switched on when the user switches to visual mode. ........................
Camera parts, 3 ....................................................................................................................................
Camera parts, 4 ....................................................................................................................................
Removable remote control .............................................................................................................
Camera buttons explanations ...................................................................................................
Camera status LCD .............................................................................................................................
Camera status LCD explanations ..............................................................................................
Wavelength: 635nm. Max. output power: 1mW. This product complies with 21 CFR
1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50, dated
July 26th, 2001 .....................................................................................................................................
Distance between the laser beam and the image center ....................................................
Explanation of measurement markers appearing in the result table ..............................
Status bar, showing atmospheric temperature, relative humidity, distance to target,
zoom factor, date & time, temperature range, emissivity, and reflected ambient
temperature. .........................................................................................................................................
Temperature scale ..............................................................................................................................
Status messages a few examples .............................................................................................
Critical camera information a few examples ........................................................................
Images folder .......................................................................................................................................
Images folder, showing the context menu ...............................................................................
Periodic save dialog box .................................................................................................................
Explanations of the Periodic save dialog box ........................................................................
4
4
5
5
9
10
12
12
13
13
22
24
24
25
25
27
28
29
30
31
32
33
36
36
37
37
38
39
39
39
40
41
42
43
43
vii
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
8.10
8.11
8.12
8.13
8.14
8.15
8.16
8.17
8.18
8.19
8.20
8.21
8.22
8.23
8.24
8.25
8.26
8.27
8.28
8.29
8.30
8.31
8.32
8.33
8.34
8.35
8.36
8.37
8.38
8.39
8.40
8.41
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
8.42
8.43
8.44
8.45
8.46
8.47
8.48
8.49
8.50
8.51
8.52
8.53
8.54
8.55
8.56
8.57
8.58
8.59
8.60
8.61
viii
Burst recording toolbar and progress bar ................................................................................

Explanations of the Burst recording toolbar ...........................................................................
Voice comment dialog box ............................................................................................................
Explanations of the Voice comment dialog box ....................................................................
Definitions of label and value .........................................................................................................
Creating a text comment .................................................................................................................
Creating a numerical value to be used in a text comment .................................................
Shortcut menu for Spot ....................................................................................................................
Explanations of the shortcut menu for Spot ............................................................................
Spot dialog box ...................................................................................................................................
Explanations of the Spot dialog box ..........................................................................................
Shortcut menu for Box .....................................................................................................................
Explanations of the shortcut menu for Box ..............................................................................
Box dialog box .....................................................................................................................................
Explanations of the Box dialog box ............................................................................................
Shortcut menu for Circle ..................................................................................................................
Explanations of the shortcut menu for Circle ..........................................................................
Circle dialog box .................................................................................................................................
Explanations of the Circle dialog box .........................................................................................
Shortcut menu for Line ....................................................................................................................
Explanations of the shortcut menu for Line .............................................................................
Line dialog box ....................................................................................................................................
Explanations of the Line dialog box ............................................................................................
Temperature scale showing an isotherm set to above +62C ..........................................
Shortcut menu for Isotherm ..........................................................................................................
Explanations of the Isotherm shortcut menu .........................................................................
Isotherm dialog box ..........................................................................................................................
Explanations of the Isotherm dialog box .................................................................................
Reference temperature dialog box .............................................................................................
Object Parameters dialog box ......................................................................................................
Range dialog box ................................................................................................................................
Symbols in the temperature scale, indicating (1) increasing span; (2) decreasing
span; (3) increasing level, and (4) decreasing level ................................................................
Palette dialog box ..............................................................................................................................
Explanations of the Palette dialog box .....................................................................................
Image Setup dialog box ..................................................................................................................
Explanations of the Image Setup dialog box ..........................................................................
Difference settings dialog box .....................................................................................................
Explanations of the Difference settings dialog box .............................................................
Save Setup dialog box ......................................................................................................................
Explanations of the Save Setup dialog box .............................................................................
Naming based on unique counter explanations ................................................................
Naming based on current date explanations ......................................................................
Naming based on current directory explanations .............................................................
Alarm Setup dialog box ...................................................................................................................
Explanations of the Alarm setup dialog box ...........................................................................
Digital video dialog box ..................................................................................................................
Explanations of the Digital video dialog box .........................................................................
Power Setup dialog box ..................................................................................................................
Explanations of the Power Setup dialog box ..........................................................................
Status bar dialog box ........................................................................................................................
Explanations of the Status bar dialog box ...............................................................................
Buttons Settings dialog box ..........................................................................................................
44
44
45
46
46
47
48
50
50
51
51
53
53
53
54
55
55
56
56
58
58
59
59
61
62
62
63
63
64
64
65
66
66
66
67
67
69
70
70
71
71
72
72
72
73
74
74
75
75
75
76
76
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
8.62
8.63
8.64
8.65
8.66
9.1
9.2
9.3
10.1
10.2
13.1
13.2
Figure
Figure
Figure
Figure
13.3
13.4
13.5
13.6
Figure 13.7
Figure 13.8
Figure 13.9
Figure 13.10
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
Figure
13.11
13.12
13.13
13.14
13.15
13.16
13.17
13.18
14.1
16.1
16.2
16.3
16.4
17.1
Figure 17.2
Figure 17.3
Figure 17.4
Figure 17.5
Figure 17.6
Figure 17.7
Explanations of the Buttons Setting dialog box ................................................................... 77

Date/Time dialog box ....................................................................................................................... 77
Explanations of the Date/Time dialog box .............................................................................. 77
Local settings dialog box ................................................................................................................ 78
Explanations of the Local settings dialog box ....................................................................... 78
Stand-alone battery charger ........................................................................................................... 81
LED indicators on the stand-alone battery charger. .............................................................. 81
LED indicators explanations ....................................................................................................... 81
Straight body LEMO connector. .................................................................................................... 84
Unlocking a LEMO connector ......................................................................................................... 85
Pin configuration for headset connector (on camera operators side) ....................... 92
Graphical representation of alarm output signal. The alarm output signal is a 1 kHz
signal with an amplitude of 2 Vpp (load 1k). The signal can drive loads as low as
16 . The signal is available in pin 1 of the headset connector. ....................................... 92
Pin configuration for RS-232/USB connector (on camera operators side) ................ 93
Video lamp, to be inserted in the RS-232/USB connector ................................................... 93
Pin configuration for remote control connector (on camera operators side) ......... 94
Pin configuration for power connector (on camera operators side). A: Center pin;
B: Chassis ............................................................................................................................................... 95
Pin configuration for CVBS connector (on camera operators side). A: Center pin;
B: Chassis ............................................................................................................................................... 95
Pin configuration for FireWire connector (on camera operators side) ....................... 95
Relationship between fields of view and distance. 1: Distance to target; 2: VFOV =
vertical field of view; 3: HFOV = horizontal field of view, 4: IFOV = instantaneous
field of view (spot size). ..................................................................................................................... 96
Horizontal, vertical and instantaneous fields of view for certain distances to targets.
D = distance to target. ...................................................................................................................... 96
F-number and close focus limits for various lenses ............................................................... 98
Overall dimensions of the battery charger ................................................................................ 99
Overall dimensions of the battery ................................................................................................ 100
Overall dimensions of the remote control ................................................................................ 101
Overall dimensions of the camera ................................................................................................ 102
Overall dimensions of the camera, when the video lamp is mounted ........................... 103
Overall dimensions of the video lamp ........................................................................................ 104
Location of the standard tripod mount (1/4"-20) on the bottom side of the camera . 105
Glossary of common infrared terms & expressions ................................................................ 106
Sir William Herschel (17381822) ................................................................................................. 112
Marsilio Landriani (17461815) ..................................................................................................... 113
Macedonio Melloni (17981854) .................................................................................................. 114
Samuel P. Langley (18341906) ..................................................................................................... 114
The electromagnetic spectrum. 1: X-ray; 2: UV; 3: Visible; 4: IR; 5: Microwaves; 6:
Radiowaves. .......................................................................................................................................... 116
Gustav Robert Kirchhoff (18241887) ......................................................................................... 117
Max Planck (18581947) ................................................................................................................... 118
Blackbody spectral radiant emittance according to Plancks law, plotted for various
absolute temperatures. 1: Spectral radiant emittance (W/cm2 103(m)); 2:
Wavelength (m) ................................................................................................................................ 119
Wilhelm Wien (18641928) ............................................................................................................. 120
Planckian curves plotted on semi-log scales from 100K to 1000K. The dotted line
represents the locus of maximum radiant emittance at each temperature as
described by Wien's displacement law. 1: Spectral radiant emittance (W/cm2 (m));
2: Wavelength (m). .......................................................................................................................... 121
Josef Stefan (18351893), and Ludwig Boltzmann (18441906) ...................................... 122
ix
Figure 17.8
Figure 17.9
Figure 18.1
Figure 18.2
Figure 18.3
Figure 18.4
Figure 19.1
Spectral radiant emittance of three types of radiators. 1: Spectral radiant emittance;

2: Wavelength; 3: Blackbody; 4: Selective radiator; 5: Graybody. .................................... 124
Spectral emissivity of three types of radiators. 1: Spectral emissivity; 2: Wavelength;
3: Blackbody; 4: Graybody; 5: Selective radiator. .................................................................... 124
A schematic representation of the general thermographic measurement situation.1:
Surroundings; 2: Object; 3: Atmosphere; 4: Camera ............................................................. 126
Voltages .................................................................................................................................................. 128
Relative magnitudes of radiation sources under varying measurement conditions
(SW camera). 1: Object temperature; 2: Emittance; Obj: Object radiation; Refl:
Reflected radiation; Atm: atmosphere radiation. Fixed parameters: = 0.88; Trefl =
20 C (+68 F); Tatm = 20 C (+68 F). ............................................................................................ 130
Relative magnitudes of radiation sources under varying measurement conditions
(LW camera). 1: Object temperature; 2: Emittance; Obj: Object radiation; Refl:
Reflected radiation; Atm: atmosphere radiation. Fixed parameters: = 0.88; Trefl =
20 C (+68 F); Tatm = 20 C (+68 F). ............................................................................................ 131
T: Total spectrum; SW: 25 m; LW: 814 m, LLW: 6.520 m; 1: Material; 2:
Specification; 3: Temperature in C; 4: Spectrum; 5: Emissivity: 6: Reference ............. 132
Warnings & cautions

10474103;1
This equipment generates, uses, and can radiate radio frequency energy and
if not installed and used in accordance with the instruction manual, may cause
interference to radio communications. It has been tested and found to comply
with the limits for a Class A computing device pursuant to Subpart J of Part 15
of FCC Rules, which are designed to provide reasonable protection against such
interference when operated in a commercial environment. Operation of this
equipment in a residential area is likely to cause interference in which case the
user at his own expense will be required to take whatever measures may be
required to correct the interference.
An infrared camera is a precision instrument and uses a very sensitive IR detector.
Pointing the camera towards highly intensive energy sources such as devices
emitting laser radiation, or reflections from such devices may affect the accuracy of the camera readings, or even harm or irreparably damage the detector. Note that this sensitivity is also present when the camera is switched off
and the lens cap is mounted on the lens.
Each camera from FLIR Systems is calibrated prior to shipping. It is advisable
that the camera is sent in for calibration once a year.
For protective reasons, the LCD (where applicable) will be switched off if the
detector temperature exceeds +60C (+149F) and the camera will be switched
off if the detector temperature exceeds +68C (+154.4F).
The camera requires a warm-up time of 5 minutes before accurate measurements (where applicable) can be expected.
In certain outdoor conditions, the sun can enter the eyepiece and cause damage
to the LCD. Use an eyepiece protector when you expect to be using the camera
for extended periods of time in outdoor sunlit environments.
Welcome!
Thank you for choosing the ThermaCAM P60 infrared camera.
The ThermaCAM P60 infrared condition monitoring system consists of an infrared
camera with a built-in 24 lens, a visual color camera, a laser pointer, an IrDA (infrared communications link), a 4" color LCD on a removable remote control, and
a range of accessories. The infrared camera measures and images the emitted infrared radiation from an object. The fact that radiation is a function of object surface
temperature makes it possible for the camera to calculate and show this temperature.
The ThermaCAM P60 camera is dust- and splash-proof and tested for shock and
vibration for use in the most demanding field conditions. It is a handheld, truly
portable camera, which is lightweight and operates for more than two hours on
one battery pack. A high-resolution color image (infrared & visual) is provided in
real-time either in the integral viewfinder or on the remote control LCD.
The camera is very easy to use and is operated by using a few buttons which are
conveniently placed on the camera, allowing fingertip control of major functions.
A built-in menu system also gives easy access to the advanced, simple-to-use
camera software for increased functionality.
To document the object under inspection it is possible to capture and store images
on a removable CompactFlash card or in the camera's internal flash memory. It is
also possible to store, together with every image, voice comments by using the
headset connected to the camera, or text comments, by selecting these from a
file with predefined text comments. The images can be analyzed either in the field
by using the real-time measurement markers built into the camera software, or
in a PC by using FLIR Systems's software for infrared analysis and reporting.
In the PC, the images can not only be viewed and analyzed, but the voice comments can also be played back. FLIR Systemss software makes it very easy to
create complete survey reports (containing numerous infrared images, photos,
tables etc.) from the inspections.
2.1
About FLIR Systems
With over 30 years experience in IR systems and applications development, and

over 30 000 infrared cameras in use worldwide, FLIR is the undisputed global
commercial IR industry leader.
2.1 About FLIR Systems

10380703;2
Figure 2.1 FLIR Systems, Boston, USA, FLIR Systems, Danderyd, Sweden, and FLIR Systems, Portland,
USA.
As pioneers in the IR industry, FLIR Systems has a long list of firsts in the world
of infrared thermography:
1965: 1st thermal imaging system for predictive maintenance (Model 650).
1973: 1st battery-operated portable IR scanner for industrial applications predictive maintenance (Model 750).
1975: 1st TV compatible system (Model 525).
1978: 1st dual-wavelength scanning system capable of real-time analog
recording of thermal events (Model 780). Instrumental in R & D market development.
1983: 1st thermal imaging and measurement system with on-screen temperature
measurement.
1986: 1st TE (thermo-electrically) cooled system.
1989: 1st single-piece infrared camera system for PM (predictive maintenance)
and R & D (research & development) with on-board digital storage.
1991: 1st Windows-based thermographic analysis and reporting system.
1993: 1st Focal Plane Array (FPA) system for PM and R & D applications.
1995: 1st full-featured camcorder style FPA infrared system (ThermaCAM).
1997: 1st: uncooled microbolometer-based PM/R & D system.
2000: 1st thermography system with both thermal and visual imaging.
2000: 1st thermography system to incorporate thermal/visual/voice and text
data logging.
2002: 1st automated thermography system (model P60) to feature detachable
remotely controllable LCD, JPEG image storage, enhanced connectivity including
USB and IrDA wireless, thermal/visual/voice and text data logging.
2002: 1st low-cost ultra-compact hand-held thermography camera (E series).
Revolutionary, ergonomic design, lightest IR measurement camera available.
2.1 About FLIR Systems

10401603;1
Figure 2.2 LEFT: FLIR Systems Thermovision Model 661. The photo is taken on May 30th, 1969 at
the distribution plant near Beckomberga, in Stockholm, Sweden. The camera weighed approx. 25 kg
(55 lb), the oscilloscope 20 kg (44 lb), the tripod 15 kg (33 lb). The operator also needed a 220 VAC
generator set, and a 10 L (2.6 US gallon) jar with liquid nitrogen. To the left of the oscilloscope the
Polaroid attachment (6 kg/13 lb) can be seen. RIGHT: FLIR Systems ThermaCAM Model E2 from 2002
weight: 0.7 kg (1.54 lb), including battery.
With this tradition of unparalleled technical excellence and innovative achievements, FLIR continues to develop new infrared products, educational venues and
applications expertise to meet the diverse demands of thermographers worldwide.
2.1.1
A few images from our facilities
10401303;1
Figure 2.3 LEFT: Development of system electronics; RIGHT: Testing of an FPA detector
2.2 Comments & questions

10401403;1
Figure 2.4 LEFT: Diamond turning machine; RIGHT: Lens polishing

10401503;1
Figure 2.5 LEFT: Testing of IR cameras in the climatic chamber; RIGHT: Robot for camera testing and
calibration
2.2
Comments & questions
FLIR Systems is committed to a policy of continuous development, and although

we have tested and verified the information in this manual to the best of our
ability, you may find that features and specifications have changed since the time
of printing. Please let us know about any errors you find, as well as your suggestions
for future editions, by sending an e-mail to:
documentation@flir.se
2.2 Comments & questions

NOTE: Do not use this e-mail address for technical support questions. Technical support is handled
by FLIR Systems local sales offices.
Packing list
The ThermaCAM P60 and its accessories are delivered in a hard transport case
which typically contains the items below. On receipt of the transport case, inspect
all items and check them against the delivery note. Any damaged items must be
reported to the local FLIR Systems representative immediately.
No.
Description
Part number
Qty
Battery
1 195 268
Adapter for CompactFlash card
1 909 820
4" LCD/remote control
1 195 346
Battery charger
1 195 267
CompactFlash card
1 909 653
FireWire cable 4/4
1 909 813
1 909 812
NOTE: Depending on your camera

configuration, this cable may be an
extra option.
7
FireWire cable 4/6

configuration, this cable may be an
extra option.
Headset
194 109
Lens cap
1 195 317
10
Operators manual
1 557 945
11
Power supply
1 909 528
12
Shoulder strap
117 132
13
ThermaCAM P60
Configuration-dependent
14
USB cable
1 195 314
15
CVBS video cable
1 909 775
16
Video lens 12
1 909 503
NOTE: Please note the following:
The packing list is, to some degree, subject to customer configuration and may contain more or
less items.
FLIR Systems reserves the right to discontinue models, parts and accessories, and other items, or
change specifications at any time without prior notice.
System overview
10440203;1
Figure 4.1 System overview
Figure 4.2 Explanations of callouts

Callout
Part No.
Description of part
194 560
Protective plastic window
1 194 977
Protective window
194 579
7 IR lens
194 176
12 IR lens
194 401
45 IR lens
194 702
80 IR lens
194 533
64/150 close-up IR lens
1 194 978
34/80 close-up IR lens
1 700 500
50 m IR lens
10
1 195 268
Battery
11
1 195 267
2-bay battery charger
12
1 909 528
External power supply
13
1 195 143
Automotive (cigarette lighter) 12 VDC adapter
14
117 132
Shoulder strap
15
1 909 820
Adapter for CompactFlash card
16
1 909 653
CompactFlash card
17
1 195 314
USB cable
18
194 109
Headset
19
1 195 346
Remote control
20
1 909 811
S-Video cable
configuration, only S-Video or FireWire is
supported.
21
1 909 812
FireWire cable 4/6

supported.
10
Callout
Part No.
Description of part
22
1 909 813
FireWire cable 6/6

supported.
23
1 909 775
CVBS cable (composite video cable)
24
IrDA
Infrared communication link
11
Connecting system components

10438603;2
Figure 5.1 How to connect system components, 1: Rear connectors

Callout
Explanation
FireWire cable
Depending on your camera configuration, this may be an S-Video cable instead
of a FireWire cable.
12
CompactFlash card
Power supply cable
CVBS cable (i.e. composite video)
Remote control cable
10438803;2
Figure 5.3 How to connect system components, 1: Front connectors

Callout
Explanation
RS-232 / USB cable.

The connector on the camera is also used as a connector for video lamp (see
figure 7.3 on page 29).
Headset cable
13
Tutorials
6.1
Switching on & switching off the camera

Step
Action
Insert a battery into the battery compartment.

SEE ALSO: For information about inserting a battery, see section 6.7.5
Inserting & removing the battery on page 23.
Briefly press the green ON/OFF button to switch on the camera.
Press and hold down the green on/off button for a few seconds to switch off
the camera.
SEE ALSO: For information about buttons, see section 7.2 Keypad buttons & functions on page 33.
6.2
Working with images
6.2.1
Acquiring an image
Step
Action
Briefly press the green ON/OFF button to switch on the camera.
Point the camera at a warm object, like a face or a hand.
Press and hold down the A button for one second to adjust the focus.
Briefly press the A button to autoadjust the camera.
6.2.2
Opening an image
Step
Action
Press the joystick to display the horizontal menu bar.
Point to Images on the File menu and press the joystick.
Select the image you want to open by moving the joystick up/down or left/right.
To recall a selected image, press the joystick.
SEE ALSO: For more information about opening images, see section 8.2.2.1 Images on page 41.
14
6.3 Working with measurements
6.2.3
Freezing & unfreezing an image
Step
Action
Briefly press the S button to freeze the image. To unfreeze the image, press
the S button once again.
6.2.4
Saving an image
Step
Action
Do one of the following:
Press and hold down the S button for a few seconds to save the image
Point to Save on the File menu and press the joystick
SEE ALSO: For more information about saving images, see section 8.2.2.2 Save on page 42.
6.3
Working with measurements
6.3.1
Laying out & moving a spot
Step
Action
Point to Add spot on the Analysis menu and press the joystick. A spot will now
appear on the screen. The measured temperature will be displayed in the result
table in the top right corner of the screen.
You are now in edit mode and can move the spot in any direction by pressing
and moving the joystick. To leave the edit mode, press the C button twice. You
can also leave the edit mode by holding down the joystick for a few seconds,
which will display a shortcut menu.
SEE ALSO: For more information about spots, see section 8.2.3.2 Add spot on page 50.
6.3.2
Laying out & moving an box
Step
Action
15
6.3 Working with measurements

Step
Action
Point to Add box on the Analysis menu and press the joystick. A box will now
You are now in edit mode and can move the box in any direction by pressing
SEE ALSO: For more information about boxes, see section 8.2.3.3 Add box on page 52.
6.3.3
Laying out & moving a circle
Step
Action
Point to Add circle on the Analysis menu and press the joystick. A circle will
now appear on the screen. The measured temperature will be displayed in the
result table in the top right corner of the screen.
You are now in edit mode and can move the circle in any direction by pressing
SEE ALSO: For more information about circles, see section 8.2.3.4 Add circle on page 55.
6.3.4
Laying out & moving a line
Step
Action
Point to Add line on the Analysis menu and press the joystick. A line will now
You are now in edit mode and can move the line in any direction by pressing
SEE ALSO: For more information about lines, see section 8.2.3.5 Add line on page 58.
16
6.4 Working with alarms
6.3.5
Creating & changing an isotherm
Step
Action
Point to Add isotherm on the Analysis menu and press the joystick. An isotherm
will now be added to your image. The isotherm levels will be displayed in the
result table in the top right corner of the screen.
You are now in edit mode and can change the isotherm levels by moving the
joystick up/down. To leave the edit mode, press the C button twice. You can
also leave the edit mode by holding down the joystick for a few seconds, which
will display a shortcut menu.
SEE ALSO: For more information about creating & changing an isotherm, see section 8.2.3.6 Add
isotherm on page 61.
6.3.6
Resizing a measurement marker
NOTE: This example procedure, which applies to all types of measurement markers, assumes that you
have laid out only one measurement box on the screen and exited the menu system.
6.4
Step
Action
Point to Edit mode on the Analysis menu and press the joystick. This will display
eight gray handles on the box.
Press the joystick once again. This will make the gray handles turn yellow.
Move the joystick left/right or up/down to select one of the yellow handles.
To resize the box, press the joystick and move it in any direction, then press
the joystick again to confirm the size.
Press the C button once to leave the edit mode.
Working with alarms
You can choose between the following alarm outputs:
a silent alarm, which, will make the background of the corresponding measurement function turn red when an alarm is triggered
an audible alarm, which, compared to the silent alarm, also triggers a beep
A settings can also be made in the camera so that an alarm output takes into account the reference temperature. A typical application when you would want to
17
use an alarm that takes into account the reference temperature is screening of
people for face temperature detection.
Firstly, the reference temperature is set by screening 10 persons with normal face
temperature. The camera puts each of these 10 results in an internal camera buffer
and calculates the average temperature value after having discarded the two
highest and two lowest values in the event of erroneous samples. Every time a
new sample is saved to the internal buffer, the oldest sample will be discarded
and a new reference temperature will be calculated on the fly.
Using an alarm that takes into account the reference temperature means that an
alarm output will only be triggered if the temperature value exceeds the sum of
the average temperature value in the buffer + the user-defined delta alarm offset
value.
6.4.1
Setting the reference temperature
Step
Action
Press the joystick to display the vertical menu bar.
Point to Buttons on the Setup menu and press the joystick.
In the Buttons setup dialog box, press the joystick up/down to go to F1 or F2.
Press the joystick left/right to select Update ref temp.
Press the joystick to confirm the choice and leave the dialog box.
Now point to Image on the Setup menu and press the joystick.
Press the joystick up/down to go to Shutter period.

Although the shutter period works independently of other functions described
in this document, FLIR Systems recommends that Short is selected when using
the camera for detection of face temperature.
NOTE: Selecting Normal will calibrate the camera at least every 15th minute,
while selecting Short will calibrate the camera at least every 3rd minute.
Pointing the camera to the first person with a normal face temperature and
pressing the F1 or F2 button will display the message Sampled nn.n C.
After having carried out the same procedure on the following 9 persons, you
can do one of the following:
18
Actively continue to sample every new person by the F1 or F2 button, and

let the camera update the reference temperature
Stop sampling and let the camera trigger an alarm as soon as the alarm
conditions are met (> reference temperature + delta alarm value)
6.4.2
Setting up a silent alarm
Step
Action
Point to Alarm on the Setup menu and press the joystick to display the Alarm
setup dialog box.
Select Type by pressing the joystick left/right. This setting defines whether the
alarm should be triggered when the temperature exceeds or drops below the
alarm temperature.
Select Function by pressing the joystick left/right. This setting defines what
measurement function should be used to trigger the alarm.
Select Identity by pressing the joystick left/right to assign an identity to the

function selected above.
Select Output by pressing the joystick left/right until Silent is highlighted.
Specify the Alarm temp by pressing the joystick left/right.

NOTE: Alarm temp will only be available if Set from ref temp has been disabled
below.
Specify whether the alarm temperature should be set from the reference
temperature or not by pressing the joystick left/right.
Specify Delta alarm by pressing the joystick left/right.

NOTE: Delta alarm will only be available if Set from ref temp has been enabled
above.
6.4.3
Setting up an audible alarm
Step
Action
Point to Alarm on the Setup menu and press the joystick to display the Alarm
setup dialog box.
Select Type by pressing the joystick left/right. This setting defines whether the
alarm should be triggered when the temperature exceeds or drops below the
alarm temperature.
Select Function by pressing the joystick left/right. This setting defines what
measurement function should be used to trigger the alarm.
Select Identity by pressing the joystick left/right to assign an identity to the

function selected above.
19
6.5 Changing level & span

Step
Action
Select Output by pressing the joystick left/right until Beep is highlighted.
Specify the Alarm temp by pressing the joystick left/right.

NOTE: Alarm temp will only be available if Set from ref temp has been disabled
below.
Specify whether the alarm temperature should be set from the reference
temperature or not by pressing the joystick left/right.
Specify Delta alarm by pressing the joystick left/right.

NOTE: Delta alarm will only be available if Set from ref temp has been enabled
above.
6.5
Changing level & span
6.5.1
Changing the level
Step
Action
If the camera is in continuous adjust mode, point to Manual adjust on the

Image menu and press the joystick.
Change the level by moving the joystick up/down. An arrow pointing upwards
or downwards will be displayed.
Press the joystick to leave level/span mode.
NOTE: You can also change the level by pointing to Level/Span on the Image menu, and then change
the level by moving the joystick up/down.
SEE ALSO: For more information about level, see section 8.2.4.4 Level/Span on page 65.
6.5.2
20
Changing the span
Step
Action
If the camera is in continuous adjust mode, point to Manual adjust on the

Image menu and press the joystick.
Change the span by moving the joystick left/right. Two arrows pointing away
from each other or towards each other will be displayed.
Press the joystick to leave level/span mode.
6.6 Changing system settings

NOTE: You can also change the span by pointing to Level/Span on the Image menu, and then change
the span by moving the joystick left/right.
SEE ALSO: For more information about span, see section 8.2.4.4 Level/Span on page 65.
6.6
Changing system settings
6.6.1
Changing the language
Step
Action
Point to Local settings on the Setup menu and press the joystick.
Move the joystick up/down to select Language.
Move the joystick left/right to change the language.
Press the joystick to confirm your changes and leave the dialog box.
NOTE: Changing the language will make the camera restart the camera
program. This will take a few seconds.
6.6.2
Changing the temperature unit
Step
Action
Point to Local Settings on the Setup menu and press the joystick.
Move the joystick up/down to select Temp unit.
Move the joystick left/right to change the temperature unit.
6.6.3
Changing the date format
Step
Action
Move the joystick up/down to select Date format.
Move the joystick left/right to change the date format.
21
6.7 Working with the camera
6.6.4
Changing the time format
Step
Action
Move the joystick up/down to select Time format.
Move the joystick left/right to change the time format.
6.6.5
Changing date & time
Step
Action
Point to Date/time on the Setup menu and press the joystick.
Move the joystick up/down to select year, month, day, minute and second.
Move the joystick left/right to change each parameter.
6.7
Working with the camera
6.7.1
Mounting an additional lens
NOTE: Before trying to remove fingerprints or other marks on the lens elements, see section 11.2
Lenses on page 86.
10396903;2
Figure 6.1 Mounting an additional lens
22

Step
Action
Make sure the index mark on the IR lens is lined up with the index mark on the
camera.
Carefully push the lens into the lens recess.

NOTE: Do not use excessive force.
6.7.2
Rotate the lens 30 clock-wise.
Focusing the camera using autofocus
Step
Action
Press the green ON/OFF button to switch on the camera.
Press and hold down the A button for one second to adjust the focus. An indicator will be displayed on the left side of the screen when focusing.
6.7.3
Focusing the camera manually
Step
Action
Adjust the focus by moving the joystick up/down. An indicator will be displayed
on the left side of the screen when focusing.
6.7.4
Using the electronic zoom
Step
Action
Adjust the zoom factor by moving the joystick left/right. An indicator will be
displayed on the left side of the screen when zooming.
6.7.5
Inserting & removing the battery
NOTE: The camera is shipped with charged batteries. To increase battery life, the battery should be
fully discharged and charged a couple of times. You can do this by using the camera until the battery
is fully depleted.
23
6.7.5.1
Inserting the battery
10397003;2
Figure 6.2 Inserting the battery

Step
Action
Open the lid of the battery compartment by pressing its locking mechanism.
Push the battery into the battery compartment until the battery release spring
locks.
Close the lid of the battery compartment.
6.7.5.2
Removing the battery
10397103;2
Figure 6.3 Removing the battery
24
Step
Action
Open the lid of the battery compartment by pressing its locking mechanism.
The battery release spring will push out the battery from the battery compartment.
Close the lid of the battery compartment.

SEE ALSO: For more information about the battery system, see section 9 Electrical power system
on page 80.
6.7.6
Removing & attaching the remote control from the camera handle
NOTE: The remote control is mounted on the camera handle by means of a fixed front latch and a
rear spring-loaded latch. See the figure on page 31.
6.7.6.1
Removing the remote control
10397203;3
Figure 6.4 Removing the remote control

Step
Action
Firmly hold the camera in your left hand and grab the handle of the remote
control in your right hand.
Pull the handle backwards until the front of the handle is released from its
latch.
You can now remove the remote control from the camera handle.
6.7.6.2
Attaching the remote control
10397303;3
Figure 6.5 Attaching the remote control
25
26
Step
Action
Firmly hold the camera in your left hand and hold the remote control in your
right hand.
Align the remote control handle with the camera handle so that the rear end
of the remote control handle mates with the rear spring-loaded latch.
Pull the remote control handle backwards and then push it down towards
the camera handle to lock it between the two latches.
Camera overview
7.1
Camera parts
10394103;4
Figure 7.1 Camera parts, 1

Callout
Description of part
+/ buttons
SEE ALSO: For more information about the functionality of this button, see
section 7.2 Keypad buttons & functions on page 33.
27
7.1 Camera parts

Callout
Description of part
F1 button
F2 button
Camera status LCD

SEE ALSO: For more information about the LCD, see section 7.5 Camera
status LCD on page 35.
Connector for remote control
Viewfinder
Removable remote control with 4" LCD
10394303;4
28
7.1 Camera parts

Callout
Description of part
C button
SEE ALSO: For more information about the C button, see section 7.2 Keypad
buttons & functions on page 33.
Lid of the battery compartment
S button
SEE ALSO: For more information about the S button, see section 7.2 Keypad
A button
SEE ALSO: For more information about the A button, see section 7.2 Keypad
Hand strap
RS-232/USB connector
The connector is also used as a connector for video lamp (see figure 7.3 on
page 29).
Headset connector
Lens
10563403;1
Figure 7.3 Video lamp, to be inserted in the RS-232/USB connector. The video lamp will automatically
be switched on when the user switches to visual mode.
29
7.1 Camera parts

10394403;4

Callout
Description of part
Cover for additional connectors
Joystick
SEE ALSO: For more information about the joystick, see section 7.2 Keypad
ON/OFF button (green)

SEE ALSO: For more information about the ON/OFF button, see section 7.2
Keypad buttons & functions on page 33.
30
7.1 Camera parts

Callout
Description of part
IrDA infrared communication link (to communicate with the camera using a
PDA, laptop computer etc.)
SEE ALSO: For more information about using IrDA, see section 7.4 IrDA
infrared communication link on page 35.
10394603;4

Callout
Description of part
Spring-loaded locking latch for the remote control
31
7.1 Camera parts

Callout
Description of part
Laser LocatIR with lens cap

A laser icon appears on the screen when the Laser LocatIR is switched on.
Since the distance between the laser beam and the image center will vary
by the target distance, Laser LocatIR should only be used as an aiming aid.
Always check the LCD to make sure the camera captures the desired target.
Do not look directly into the laser beam.
When not in use, the Laser LocatIR should always be protected by the lens
cap.
SEE ALSO: For more information about Laser LocatIR, see section 7.6 Laser
LocatIR on page 37.
Button for Laser LocatIR

SEE ALSO: For more information about Laser LocatIR, see section 7.6 Laser
LocatIR on page 37.
Visual camera
SEE ALSO: For more information about the visual camera, see section 7.7
Visual camera on page 37.
10395003;3
Figure 7.6 Removable remote control
32
7.2 Keypad buttons & functions

Callout
Description of part
S button
SEE ALSO: For more information about the S button, see section 7.2 Keypad
C button
SEE ALSO: For more information about the C button, see section 7.2 Keypad
A button
SEE ALSO: For more information about the A button, see section 7.2 Keypad
Joystick
SEE ALSO: For more information about the joystick, see section 7.2 Keypad
7.2
Keypad buttons & functions
Figure 7.7 Camera buttons explanations

Button
Comments
ON/OFF
Press briefly to switch on the camera

Press and hold down for a few seconds to switch off the camera
Press briefly to autoadjust the camera
Press and hold down for a few seconds autofocus the camera
Press briefly to freeze an image
Press briefly to store an image if the image is currently frozen
Press and hold down for a few seconds to store without
freezing the image
Press to move between panes in some dialog boxes
Press to leave freeze mode and go to live mode
Press to leave dialog boxes without changing any settings
Press twice to leave edit mode
If the camera is in manual adjust mode, press to change the
function of the joystick to level (up/down) and span (left/right)
33
7.3 Autofocus
Button
Comments
Joystick
+/
Programmable functions:
F1
Focus
Zoom
Level
Span
F2
None
Adjust once
Auto focus
Reverse palette
Next palette
Visual/IR
Update ref temp
Button for Laser LocatIR
7.3
Press to display the menu system

Press to exit the menu system
Press to confirm selections and leave dialog boxes
Press to select measurement markers
Move up/down or left/right to navigate in menus, dialog
boxes, and on the screen
Move up/down or left/right to move or resize measurement
markers
Move up/down to change focus and left/right to zoom
If the camera is in manual adjust mode, press C to change the
function of the joystick to level (up/down) and span (left/right)
None
Adjust once
Auto focus
Reverse palette
Next palette
Visual/IR
Update ref temp
Press to switch on Laser LocatIR
Autofocus
To focus the camera using the autofocus feature, press and hold down the A
button for one second.
34
7.4 IrDA infrared communication link

The area that the camera uses when autofocusing is a 80 60 pixel box, centered vertically and
horizontally on the screen
The camera will have difficulties autofocusing when the image has low contrasts between different
areas
You should keep the camera steady when autofocusing
7.4
IrDA infrared communication link
If you have access to a PDA or a laptop computer equipped with an IrDA infrared
communication link, you can upload text comment files (*.tcf) to the internal flash
memory in ThermaCAM P60.
Step
Action
ThermaCAM Reporter 7.0 a reporting software from FLIR Systems provides

a user-friendly interface to create text comment files. Create your text comment
file using this software, but save the file to Desktop as a pure text file (*.txt)
instead of as a text comment file (*.tcf).
NOTE: For more information about using the text comment editor in
ThermaCAM Reporter 7.0, consult any of the following manuals:
7.5
ThermaCAM Reporter Pro 7.0 Manuel dutilisation (1 557 790)

ThermaCAM Reporter Pro 7.0 Bedienungsanleitung (1 557 792)
ThermaCAM Reporter Pro 7.0 Manual del usuario (1 557 794)
ThermaCAM Reporter Pro 7.0 Manuale dell'operatore (1 557 796)
ThermaCAM Reporter Pro 7.0 User's Manual (1 557 788)
Transfer the *.txt file to your PDA (or laptop, if you created the file on a desktop
computer).
Point to Text comment on the File menu in ThermaCAM P60 and press the
joystick.
Upload the file from the PDA (or laptop) to ThermaCAM P60. A dialog box
will confirm receipt of the file.
Camera status LCD
The camera status LCD on the left side of the camera displays information about
battery status, communication status, memory status etc.
35
7.5 Camera status LCD

10346003;2
Figure 7.8 Camera status LCD

Figure 7.9 Camera status LCD explanations
Callout
Comments
Battery status bar. The frame around the battery status bar is switched on when
a battery is inserted.
Battery indicator. Switched on if a battery is inserted, flashing if the battery is

being charged internally.
CompactFlash card indicator. Switched on if a CompactFlash card is inserted.
CompactFlash status bar:
All segments switched on = the card is empty

All segments switched off = the card is full
Not implemented
Burst recording indicator. Switched on during burst recording.
Communication indicator. Switched on when a communication link is active.
Power indicator:
36
All segments switched on = fully charged battery

All segments switched off = empty battery or no battery inserted
Both segments switched on when the camera is switched on

Both segments switched off when the camera is switched off
The outer segment flashing when the camera is in deep sleep
External power indicator. Switched on when the camera is externally powered.
7.6 Laser LocatIR
7.6
Laser LocatIR
The ThermaCAM P60 infrared camera features a laser pointer located at the
front of the camera handle. To display the laser dot, press the Laser LocatIR button
on left side of the handle. The laser dot will appear approx. 91 mm/3.6" above the
target.
A laser icon appears on the screen when the Laser LocatIR is switched on.
Since the distance between the laser beam and the image center will vary by the target distance,
Laser LocatIR should only be used as an aiming aid. Always check the LCD to make sure the camera
captures the desired target.
Do not look directly into the laser beam.
When not in use, the Laser LocatIR should always be protected by the lens cap.
10376403;2
Figure 7.10 Wavelength: 635nm. Max. output power: 1mW. This product complies with 21 CFR
1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50, dated July 26th, 2001
10395103;3
Figure 7.11 Distance between the laser beam and the image center
7.7
Visual camera
The ThermaCAM P60 infrared camera features a visual camera located at the
front of the camera handle. The visual camera has no motorized focus and you
will need to occasionally focus the camera by rotating the lens manually.
37
Camera program
8.1
Screen objects
8.1.1
Result table
The results of measurement markers are displayed in a result table in the top righthand corner of the screen.
Figure 8.1 Explanation of measurement markers appearing in the result table
Icon
Explanation
Spot
Box 1, maximum temperature
Box 1, minimum temperature
Box 1, average temperature
Circle 1, maximum temperature
Circle 1, minimum temperature
Circle 1, average temperature
Line 1, maximum temperature
Line 1, minimum temperature
Line 1, average temperature
Line 1, cursor temperature
Isotherm 1, above
Isotherm 1, below
Isotherm 1, interval
Isotherm 1, dual above
Isotherm 1, dual below
XXXYYY
Difference calculation
Camera reference temperature
38
8.1 Screen objects
8.1.2
Status bar
10388403;2
Figure 8.2 Status bar, showing atmospheric temperature, relative humidity, distance to target, zoom
factor, date & time, temperature range, emissivity, and reflected ambient temperature.
Information about an image and the current conditions appear on the first and
second bottom lines of the screen. If text comments are attached to an image file,
they are displayed above these two lines.
NOTE: If you enter an emissivity value less than 0.30 the emissivity box will begin flashing to remind
you that this value is unusually low.
8.1.3
Temperature scale
10388503;2
Figure 8.3 Temperature scale
The temperature scale is displayed on the right-hand side of the screen. The scale
shows how the colors are distributed along the various temperatures in the image,
with high temperatures at the upper end and low temperatures at the lower end.
8.1.4
System messages
8.1.4.1
Status messages
Status messages are displayed at the bottom of the screen, or in the top left part
of the screen. Here you will find information about the current status of the camera,
etc.
Figure 8.4 Status messages a few examples
Message
Explanation
Frozen
Message is displayed when the image is frozen.
39
8.2 Menu system

Message
Explanation
Manual
Message is displayed when the camera is currently in manual

adjust mode.
Restarting
Message is displayed when the software is restarted, i.e. after

Factory default.
Saving as
Message is displayed while an image is being saved.
8.1.4.2
Warning messages
Warning messages are displayed in the center of the screen. Here you will find
important information about battery status, etc.
Figure 8.5 Critical camera information a few examples
Message
Explanation
Battery low
The battery level is below a critical level.
Shutting down
The camera will be switched off immediately.
Shutting down in 2 seconds
The camera will be switched off in 2 seconds.
8.2
Menu system
8.2.1
Navigating in the menu system
40
Press the joystick to display the horizontal menu bar

Press the joystick to confirm selections in menus and dialog boxes
Press the C button to exit the menu system
Press the C button to cancel selections in menus and dialog boxes
Move the joystick up/down to move up/down in menus, submenus and dialog
boxes
Move the joystick right/left to move right/left in menus and submenus, and to
change values in dialog boxes
8.2 Menu system
8.2.2
File menu
8.2.2.1
Images
10565703;1
Figure 8.6 Images folder
Point to Images and press the joystick to display a thumbnail view of the files on
the CompactFlash card, or in the internal camera memory. The following files
are displayed:
infrared images
visual images
*.avi files (DV-AVI files captured using burst recording)
*.etf files (emissivity table files)
*.tcf files (text comment files)
41
8.2 Menu system

10565803;1
Figure 8.7 Images folder, showing the context menu
In the Images folder you can do the following:
Open an image by selecting the image using the joystick, then pressing the
joystick
Create a new folder by selecting an image, then pressing and holding down
the joystick, and selecting Create new folder
Delete an image by selecting the image, then pressing and holding down the
joystick, and selecting Delete
Move between the internal memory and the CompactFlash card
8.2.2.2
Save
Point to Save and press the joystick to save the displayed image to the internal
flash memory, or the CompactFlash card.
SEE ALSO: For more information about saving images, and using voice and text comments, see section
8.2.5.3 Save on page 70, 8.2.2.6 Voice comment on page 45and 8.2.2.7 Text comment on page
46.
8.2.2.3
Copy to card
Point to Copy to card to copy the contents of the internal image folder to a automatically created folder on a CompactFlash card
42
8.2 Menu system
8.2.2.4
Periodic save
10389603;2
Figure 8.8 Periodic save dialog box
Point to Periodic save and press the joystick to display the Periodic save dialog
box. Using the periodic save feature, you can save a number of images, at a certain
selectable periodicity, to the internal flash memory or the CompactFlash card.
Together with the images, all the current conditions will be saved.
Figure 8.9 Explanations of the Periodic save dialog box
Task
Action
Comment
Setting the periodicity
Move the joystick left/right
The periodicity can be set from

10 seconds up to 24 hours. Select Fast On for shortest
possible time interval (< 10
seconds).
Starting the recording
Press the joystick
Stopping the recording
Press the joystick again

NOTE: Images will be stored sequentially in the current directory.
If the recording is stopped and then started again the new images
will be added at the end of the previous sequence in the same
directory.
8.2.2.5
Burst recording
NOTE: Depending on your camera configuration, this feature may be an extra option.
Point to Burst recording and press the joystick to display the Burst recording dialog box. Using the burst recording feature, you can:
record and save a sequence of frames at a very high speed

save specific frames as infrared images
play back the sequence backward and forward
set stop and start frames in a sequence to save a part of the sequence
choose between looped or linear recording mode
43
8.2 Menu system

10389703;2
Figure 8.10 Burst recording toolbar and progress bar

Figure 8.11 Explanations of the Burst recording toolbar
44
Callout
Explanation
Go to beginning of frame sequence
Go to previous frame in the frame sequence
Play back the frame sequence backward
Stop the recording or the playback of the frame sequence
Play back the frame sequence forward
Go to the next frame in the frame sequence
Go to the end of the frame sequence
Set start frame for saving of the frame sequence
Set stop frame for saving of the frame sequence
8.2 Menu system

Callout
Explanation
10
As File type, select AVI (non-radiometric) or SEQ (radiometric).

As Record mode, select Circular or Linear. Circular means that the recording
will automatically start over when the internal RAM memory is full. This may
be useful when it is extremely important that the beginning of an event is
recorded, and it is difficult to start the recording at the exact time. Linear
means that the recording will start when you click button 11 and stop when
the internal RAM memory is full (unless the recording is stopped manually).
Set the frame rate by specifying a number in the bottom row. For example,
setting the frame rate to 2 means 25 or 30 Hz, depending on TV system.
NOTE: The AVI recording will be saved as a DV-AVI file.

10565303;1
11
Record a frame sequence
12
Open a saved frame sequence (a *.seq file or an *.avi file)
13
Save the current frame as an IR image
14
Open a saved frame sequence (a *.seq file or an *.avi file)
8.2.2.6
Voice comment
10389803;2
Figure 8.12 Voice comment dialog box
Point to Voice comment and press the joystick to display the Voice comment
dialog box. A progress bar in the dialog box will indicate the progress of the voice
recording. Using the voice comment feature, you can:
listen to a recorded comment, make a pause, and then continue

record a new comment, make a pause, and then continue
edit a recorded comment, i.e. listen and/or add a comment at the end of the
recorded comment
overwrite an existing recording
45
8.2 Menu system

Figure 8.13 Explanations of the Voice comment dialog box
Task
Action
Recording a new voice comment, using the

headset
Move the joystick to select the Record button

and then press the joystick.
Stopping the recording
Move the joystick to select the Stop button and

then press the joystick.
Listening to a voice comment, using the headset
Move the joystick to select the Play button and

then press the joystick.
Saving the current voice comment
Move the joystick to select the Save button and

then press the joystick, or press the S button.
8.2.2.7
Text comment
Point to Text comment and press the joystick to display the Text comment dialog
box. Using the text comment feature, you can annotate images by using a file
with predefined text strings. Such a file can be created and edited in FLIR Systems's
PC software for example, in ThermaCAM Reporter 7.0.
The concept of text comments is based on two important definitions label and
value. The following examples explain what the difference between the two definitions is:
Figure 8.14 Definitions of label and value
46
Label (examples)
Value (examples)
Company
FLIR Systems
Building
Workshop
Section
Room 1
Equipment
Tool 1
Recommendation
Repair
8.2 Menu system

Figure 8.15 Creating a text comment
Step
Action
Point to Text comment on the File menu and press the joystick. A dialog box
with a number of tabs will appear on the screen. Move the joystick up/down
to select a label on the first tab, and then press the joystick.
10566003;1
Move the joystick up/down to select a value on the second tab, and press the
joystick.
10566103;1
To see the complete result, move the joystick to the right to go to the third
tab.
Press the S button to save the text comment and leave the dialog box.
47
8.2 Menu system

Figure 8.16 Creating a numerical value to be used in a text comment
Step
Action
Point to Text comment on the File menu and press the joystick. A dialog box
with four tabs will appear on the screen. Move the joystick up/down to select
a label on the first tab, and then press the joystick.
10566003;1
To specify a numerical value that you can select on the first tab, select Numerical value and press the joystick.
10566203;1
48
8.2 Menu system

Step
Action
Move the joystick up/down and left/right to specify a numerical value. Spaces
before and after the value will be deleted.
10566303;1
To keep the text comment for future use, select Yes on the Settings tab.
10566403;1
To include the numerical value in your text comment, go back to the first tab
and select the value.
Press the S button to save the text comment and leave the dialog box.
49
8.2 Menu system

Using the text comments command requires that a CompactFlash card with the appropriate *.tcf
file is inserted into the camera, or that the file is stored in the cameras internal flash memory. To
make the text strings load, it is important that the *.tcf file is saved on image root level or in the
directory where the images are saved on the CompactFlash card. If the images are saved in the
internal flash memory, the *.tcf file should be in the same directory as the images.
For more information about using the text comment editor in ThermaCAM Reporter 7.0, consult
any of the following manuals:
ThermaCAM Reporter 7.0 Bedienungsanleitung (1 557 792)

ThermaCAM Reporter 7.0 Manuel dutilisation (1 557 790)
ThermaCAM Reporter 7.0 Manual del usuario (1 557 794)
ThermaCAM Reporter 7.0 Manuale dell'operatore (1 557 796)
ThermaCAM Reporter 7.0 Operator's manual (1 557 788)
8.2.3
Analysis menu
8.2.3.1
Edit mode
Point to Edit mode and press the joystick to enter the edit mode of the camera.
When the camera is in edit mode you can select, move, and resize measurement
markers as well as changing levels of isotherms etc. You leave edit mode by
pressing the C button.
8.2.3.2
Add spot
Point to Add spot and press the joystick to add a spot. A spot will now be displayed
on the screen. Press and hold down the joystick for one second when the spot is
selected to display a shortcut menu.
10390103;2
Figure 8.17 Shortcut menu for Spot

Figure 8.18 Explanations of the shortcut menu for Spot
50
Command
Explanation
Delete
Point to Delete and press the joystick to delete the spot.
Exit edit mode
Point to Exit edit mode and press the joystick to exit the edit
mode.
Set as ref temp
Point to Set as ref temp and press the joystick to use the spot
temperature as the reference temperature.
8.2 Menu system

Command
Explanation
Settings
See below.
Point to Settings and press the joystick to display a Spot settings dialog box
where you can change the settings for the spot.
10390203;2
Figure 8.19 Spot dialog box

Figure 8.20 Explanations of the Spot dialog box
Label
Value
Local
On
Off
Comments
Select On to set the emissivity,
the reflected temperature, and
the distance for this spot only.
Selecting On will also assign an
asterisk to the measurement
markers label.
Emissivity
User-defined (0.011.00)
You can set the Emissivity if

Local is enabled. If not, this
option will be shaded.
NOTE: If you enter an
emissivity value less than 0.30
the emissivity box will begin
flashing to remind you that this
value is unusually low.
51
8.2 Menu system

Label
Value
Comments
Emissivity table
User-defined
Press the button to the right of

Emissivity table to display an
emissivity table on the screen.
You can use this emissivity table to find emissivities for a
number of different materials.
An emissivity table can be created and edited in FLIR Systemss PC software.
NOTE: The emissivity file can
be stored at root level or at
directory level. However, the
camera software prioritizes files
that are stored at directory
level and the directory has to
be selected in order to store
the emissivity file in the camera
memory. If the camera
software does not find an
emissivity file at directory level,
it searches for similar files at
root level and saves those
instead.
T Reflected
User-defined
You can set T Reflected if Local

is enabled. If not, this option
will be shaded.
Distance
User-defined
You can set Distance if Local is

enabled. If not, this option will
be shaded.
Label
8.2.3.3
On
Off
Select On to assign a label to

the measurement marker (a
small box with a number).
Add box
Point to Add box and press the joystick to add a box. A box will now appear on
the screen. Press and hold down the joystick for one second when the box is selected to display a shortcut menu.
52
8.2 Menu system

10390303;2
Figure 8.21 Shortcut menu for Box

Figure 8.22 Explanations of the shortcut menu for Box
Command
Explanation
Delete
Point to Delete and press the joystick to delete the box.
Exit edit mode
mode.
Set as ref temp
Point to Set as ref temp and press the joystick to use the box
Max
Point to Max and press the joystick to display the maximum

temperature of the box
Min
Point to Min and press the joystick to display the minimum temperature of the box
Avg
Point to Avg and press the joystick to display the average temperature of the box.
Settings
See below.
Point to Settings and press the joystick to display a Box settings dialog box where
you can change the settings for the box.
10390403;2
Figure 8.23 Box dialog box

53
8.2 Menu system

Figure 8.24 Explanations of the Box dialog box
Label
Value
Local
Comments
On
Off

the distance for this box only.
markers label.
Emissivity

Emissivity table
User-defined

instead.
T Reflected
54
User-defined

will be shaded.
8.2 Menu system

Label
Value
Comments
Distance
User-defined

be shaded.
Label
Result
Show Max/Min
8.2.3.4
On
Off

Min
Max
Avg
To change how the measurement results will be displayed,

select Max, Min, or Avg.
On
Off
To display two moving cursors

inside the box, continuously
indicating the maximum and
minimum temperature, select
On.
Add circle
Point to Add circle and press the joystick to add a circle. A circle will now appear
on the screen. Press and hold down the joystick for one second when the circle
is selected to display a shortcut menu.
10390503;2
Figure 8.25 Shortcut menu for Circle

Figure 8.26 Explanations of the shortcut menu for Circle
Command
Explanation
Delete
Point to Delete and press the joystick to delete the circle.
Exit edit mode
mode.
Set as ref temp
Point to Set as ref temp and press the joystick to use the circle
55
8.2 Menu system

Command
Explanation
Max

temperature of the circle.
Min
Point to Min and press the joystick to display the minimum temperature of the circle.
Avg
Point to Avg and press the joystick to display the average temperature of the circle
Settings
See below.
Point to Settings and press the joystick to display a Circle settings dialog box
where you can change the settings for the circle.
10390603;2
Figure 8.27 Circle dialog box

Figure 8.28 Explanations of the Circle dialog box
Label
Value
Local
Comments
On
Off

the distance for this circle only.
markers label.
Emissivity

56
8.2 Menu system

Label
Value
Comments
Emissivity table
User-defined

instead.
T Reflected
User-defined

will be shaded.
Distance
User-defined

be shaded.
Label
Result
Show Max/Min
On
Off

Min
Max
Avg
To change how the circle displays the measurement results,

select Max, Min, or Avg.
On
Off
To display two moving cursors

inside the circle, continuously
indicating the maximum and
minimum temperature, select
On.
57
8.2 Menu system
8.2.3.5
Add line
Point to Add line and press the joystick to add a line. A line will now appear on
the screen. Press and hold down the joystick for one second when the line is selected to display a shortcut menu.
10390703;2
Figure 8.29 Shortcut menu for Line

Figure 8.30 Explanations of the shortcut menu for Line
58
Command
Explanation
Delete
Point to Delete and press the joystick to delete the line.
Exit edit mode
mode.
Show profile
Point to Show profile and press the joystick to display a profile

window. The profile window displays the different temperature
levels along the line as a graph.
Set as ref temp
Point to Set as ref temp and press the joystick to use the line
Cursor
Point to Cursor and press the joystick to display a cursor that you
can move along the line.
Max

temperature along the line.
Min
Point to Min and press the joystick to display the minimum temperature along the line.
Avg
Point to Avg and press the joystick to display the average temperature along the line.
Settings
See below.
8.2 Menu system
Point to Settings and press the joystick to display a Line settings dialog box where
you can change the settings for the line.
10390803;2
Figure 8.31 Line dialog box

Figure 8.32 Explanations of the Line dialog box
Label
Value
Local
On
Off
Comments
the distance for this line only.
markers label.
Emissivity

59
8.2 Menu system

Label
Value
Comments
Emissivity table
User-defined

instead.
T Reflected
User-defined

will be shaded.
Distance
User-defined

be shaded.
Result
Orientation
60
Min
Max
Avg
Point to Max, Min or Avg and

press the joystick to change
how the line displays the measurement results
Horizontal
Vertical
Point to Horizontal or Vertical

and press the joystick to make
the line horizontal or vertical.
8.2 Menu system

Label
Value
Mode
Full
Aligned
Comments
Point to Full and press the joystick to make the line be of the
same width or height as the
screen.
Point to Aligned and press the
joystick to make the line be of
the same width or height as
the profile box.
8.2.3.6
Add isotherm
The isotherm command colors all pixels with a temperature above, below or between one or more preset temperature levels.
10390903;2
Figure 8.33 Temperature scale showing an isotherm set to above +62C
Point to Add isotherm and press the joystick to add an isotherm. An isotherm has
now be added to your image. Press and hold down the joystick for one second
when the isotherm (in the temperature scale) is selected to display a shortcut
menu.
61
8.2 Menu system

10391003;2
Figure 8.34 Shortcut menu for Isotherm

Figure 8.35 Explanations of the Isotherm shortcut menu
Command
Explanation
Delete
Point to Delete and press the joystick to delete the isotherm.
Exit edit mode
mode.
Set as ref temp
Point to Set as ref temp and press the joystick to use the isotherm
Above
All pixels with a temperature higher than a set temperature will

be colored with the same preset isotherm color.
Below
All pixels with a temperature lower than a set temperature will

be colored with the same preset isotherm color.
Interval
All pixels with a temperature within the set interval will be colored
with the same preset isotherm color.
Dual Above
All pixels in two consecutive temperature ranges above a set

temperature will be colored with two different preset isotherm
colors.
Dual Below
All pixels in two consecutive temperature ranges below a set

temperature will be colored with two different preset isotherm
colors.
Settings
See below
Point to Settings and press the joystick to display an Isotherm settings dialog
box where you can change the settings for the isotherm.
62
8.2 Menu system

10397403;2
Figure 8.36 Isotherm dialog box

Figure 8.37 Explanations of the Isotherm dialog box
Label
Value
Type
Interval
Above
Below
Dual Above
Dual Below
Comments
SEE: For an explanation of
isotherm types, see above.
Level
User-defined
The temperature level in degrees Celsius (C) or degrees

Fahrenheit (F).
Width
User-defined
The temperature width in degrees Celsius (C) or degrees

Fahrenheit (F).
Color
The colors used for the

isotherm.
Attribute
Transparent
Solid
Selecting Transparent will add

some transparency to an
isotherm color, making it easier
for you to see objects through
the color.
To make the isotherm colors
appear solid, select Solid.
Label
8.2.3.7
On
Off
Selecting On will assign a label

to the measurement marker (a
Add diff
Point to Add diff and press the joystick to add a difference calculation, which will
appear in the result table.
SEE ALSO: For more information about difference calculations, see section 8.2.5.2 Difference on
page 69.
63
8.2 Menu system
8.2.3.8
Ref temp
10391403;2
Figure 8.38 Reference temperature dialog box
The reference temperature can be used when the camera calculates temperature
differences
Point to Ref temp and press the joystick to set the temperature
To change the temperature, move the joystick up/down
Press the joystick to leave the dialog box
8.2.3.9
Remove all
Point to Remove all and press the joystick to remove all measurement functions
and markers from the screen.
8.2.3.10
Obj par
10439203;1
Figure 8.39 Object Parameters dialog box
You use this command to set the object parameters Emissivity, Distance, T Reflected, T Atmosphere, Rel humidity, External optics, Optics transmission, and
Optics temperature. The parameters are selected by moving the joystick up/down
and set by moving the joystick left/right. These parameters settings will be used
by all measurement functions that have not been set locally.
Click Emissivity table to display an emissivity table on the screen. You can use
this emissivity table to find emissivities for a number of different materials. An
emissivity table can be created and edited in FLIR Systemss PC software.
64
8.2 Menu system

The emissivity file can be stored at root level or at directory level. However, the camera software
prioritizes files that are stored at directory level and the directory has to be selected in order to
store the emissivity file in the camera memory. If the camera software does not find an emissivity
file at directory level, it searches for similar files at root level and saves those instead.
If you enter an emissivity value less than 0.30 the emissivity box will begin flashing to remind you
that this value is unusually low.
The transmission factor is applied to the signal and not to the temperature
SEE ALSO: For more information about object parameters, see section 15 Thermographic
measurement techniques on page 110.
8.2.3.11
Deactivate local par.
Point to Deactivate local par. and press the joystick to delete all locally set parameters. Locally set parameters are the parameters you set in e.g. the Spot settings
dialog box.
8.2.4
Image menu
8.2.4.1
Visual/IR
Point to Visual/IR and press the joystick to switch between visual mode and IR
mode.
8.2.4.2
Freeze/Live
Point to Freeze/Live and press the joystick to switch between freeze image mode
and live image mode. It has the same effect as briefly pressing the S button.
8.2.4.3
Range
10391903;4
Figure 8.40 Range dialog box
Point to Range and press the joystick to display a dialog box where you can set
the range.
8.2.4.4
Level/Span
Point to Level/Span and press the joystick to manually change level and span. The
level command can be regarded as the brightness, while the span command can
be regarded as the contrast.
Move the joystick up/down to change the level (indicated by an arrow pointing
upwards or downwards in the temperature scale)
Move the joystick left/right to change the span (indicated by two arrows
pointing away from each other or towards each other)
65
8.2 Menu system

10392103;3
Figure 8.41 Symbols in the temperature scale, indicating (1) increasing span; (2) decreasing span; (3)
increasing level, and (4) decreasing level
SEE ALSO: For more information about object parameters, see section 15 Thermographic
measurement techniques on page 110.
8.2.4.5
Manual adjust / Continuous adjust
Point to Manual adjust and press the joystick to put the camera in manual adjust
mode. You can now change level and span by first pressing the C button repeatedly (to change the function of the joystick to level/span), and then change
level or span by moving the joystick up/down and left/right, respectively
Point to Continuous adjust and press the joystick to put the camera in automatic
mode, continuously optimizing the image for best level and span
SEE ALSO: For more information about the Level/Span command, see section 8.2.4.4 Level/Span
on page 65.
8.2.4.6
Palette
10392003;2
Figure 8.42 Palette dialog box
Point to Palette and press the joystick to display a dialog box where you can
change the color palette.
Figure 8.43 Explanations of the Palette dialog box
Label
Value
Comments
Palette
Move the joystick left/right to

change the palette.
Inverted
Yes
No

reverse the current palette.
Custom palettes (*.pal) can be used by the camera. For more information about
how to create custom palettes, contact FLIR Systems.
66
8.2 Menu system
8.2.4.7
Hide graphics
Point to Hide graphics and press the joystick to hide all on-screen graphics (e.g.
result table, status bar etc.). To display the graphics again, press the joystick or the
C button.
8.2.4.8
Add visual marker
You can add a visual marker to an image when the camera is in visual mode by
pointing to Add visual marker and press the joystick. By moving the joystick
up/down or left/right you can move the marker on the image and place it where
you want it to be.
8.2.5
Setup menu
NOTE: Depending on camera configuration, some menu items on the Setup menu may be displayed
in a different order, or on a submenu.
8.2.5.1
Image
10439803;1
Figure 8.44 Image Setup dialog box

Figure 8.45 Explanations of the Image Setup dialog box
Label
Value
Adjust method
Scale
Status bar
Comments
Level
Level-span
Histogram

change the adjust method.
On
Off

enable or disable the scale.
On
Off

enable or disable the status
bar.
These settings influence the

image quality and different
settings may be suitable for
different types of images
and/or applications.
67
8.2 Menu system

Label
Value
Saturation colors
On
Off
Comments
enable or disable the saturation colors.
If On is selected the areas that
contain temperatures outside
the present level/span settings
are colored with the saturation
colors. The saturation colors
contain an overflow color and
an underflow color.
There is also a third red saturation color that marks everything saturated by the detector
indicating that the range
should be changed.
Adjust region
68
Press the Adjust region button

to display a region on the
screen that will be used when
autoadjusting the camera.
8.2 Menu system

Label
Value
Shutter period
Normal
Short
Off
Comments
Press the joystick left/right to
change the shutter period, or
switch off the shutter.
NOTE: Please note the
following:
8.2.5.2
Although the shutter period

works independently of
other functions described
in this publication, FLIR
Systems recommends that
Short is selected when
using the camera for
detection of face
temperature.
Selecting Normal will
calibrate the camera at least
every 15th minute, while
selecting Short will calibrate
the camera at least every
3rd minute.
If the shutter is switched off,
a symbol (*) will prefix the
result at the time a shutter
sequence should have
taken place, thus indicating
uncertainty in the
measurement result.
Difference
10393203;2
Figure 8.46 Difference settings dialog box
Difference is a command that calculates the temperature difference between two

measurement markers, or the reference temperature and a measurement marker.
69
8.2 Menu system

Figure 8.47 Explanations of the Difference settings dialog box
Label
Value
Comments
Function

select the first function in the
difference calculation.
Identity
110
Select a number between 1

and 10 to assign an identity to
this function.
Result
Depending on the Function

settings

define the type of result the
difference calculation will use
for its calculations.
Function

select the second function in
the difference calculation.
Identity
110
Select a number between 1

and 10 to assign an identity to
this function.
Result
Depending on the Function

settings

define the type of result the
difference calculation will use
for its calculations.
8.2.5.3
Save
10393403;2
Figure 8.48 Save Setup dialog box
70
8.2 Menu system

Figure 8.49 Explanations of the Save Setup dialog box
Label
Value
Prompt comment
Comments
None
Text
Voice
Prompt visual
Image naming
Overlay
Yes
No
If Text is selected, the text

comment dialog box will
appear when you save an
image. This function gives
you a chance to add a text
comment to the image.
If Voice is selected, the
voice comment dialog box
will appear when you save
an image. This function
gives you a chance to add a
voice comment to the image.
If Yes is selected, the camera

will change to visual mode
when you save an image. This
function gives you a chance to
add a visual image to the infrared image.
Unique counter
Date
Directory
SEE: For a detailed explanation,

see below.
On
Off
If On is selected, all onscreen graphics will be

saved together with the image
If Off is selected, only the
image (together with any
temperature information)
will be saved
NOTE: The difference between

images saved with or without
on-screen graphics will only be
evident when looking at the
images using a third-party
image viewer.
Figure 8.50 Naming based on unique counter explanations
Typical syntax: IR_nnnn.jpg
IR or DC or SEQ
nnnn
IR = infrared image
DC = visual image
SEQ = sequence image
Unique counter
71
8.2 Menu system

Example
IR_0003.jpg
Comment
The counter will be reset when exceeding 9999,

or when you point to Factory default on the
Setup menu and press the joystick.
Figure 8.51 Naming based on current date explanations

Typical syntax: IR_YYMMDD_nnn.jpg
IR or DC or SEQ
IR = infrared image
DC = visual image
YYMMDD
Current date. The format depends on your settings in the Local settings dialog box.
nnn
Counter within directory
Example
IR_020909_001.jpg
Comment
The counter will be reset every day.
Figure 8.52 Naming based on current directory explanations

Typical syntax: IR_DIRE_nnn.jpg
IR or DC or SEQ
IR = infrared image
DC = visual image
DIRE
The first four letters in the directory name
nnn
Counter within directory
Example
IR_ COMP_003.jpg
8.2.5.4
Alarm
10439703;1
Figure 8.53 Alarm Setup dialog box
72
8.2 Menu system

Figure 8.54 Explanations of the Alarm setup dialog box
Label
Value
Type
Off
Above
Below
Explanation
Select Off to disable the

alarm.
Select Above to assign an
alarm color to all pixels
above the alarm temperature.
Select Below to assign an
alarm color to all pixels below the alarm temperature.
Function
Select any one of the measurement functions to define which

function's temperature value
should trigger the alarm.
Identity
Select a number to assign an

identity to the function above.
Output
Silent
Beep
Alarm temp
User-defined
Set from ref temp
Yes
No
Select Silent to make the

background of the corresponding measurement
function turn red when an
alarm is triggered
Select Beep to additionally
make the camera trigger a
beep when an alarm is triggered.
Enter a temperature value by

pressing the navigation pad
left/right.
Select Yes or No to define
whether the alarm temperature should be set from the
reference temperature of the
camera or not.
Delta alarm
N/A
Enter an delta alarm value by

pressing the navigation pad
left/right.
Ref temp
User-defined
For information purposes only.

The reference temperature is
calculated and updated on the
fly.
73
8.2 Menu system
8.2.5.5
Digital video
NOTE: Depending on your camera configuration, this feature may in whole or in part be an extra
option.
10402903;1
Figure 8.55 Digital video dialog box

Figure 8.56 Explanations of the Digital video dialog box
Label
Value
Mode
DCAM
DV
Comments
NOTE: Disconnect the FireWire
cable from the camera before
carrying out this procedure.
select digital video mode (DV
or DCAM).
Link
Active
Idle
NOTE: Link status settings

should only be changed when
DV mode is selected above.
74
When establishing a connection between the camera

and a passive digital video
unit such as a DV recorder
the image transmission
needs to be activated from
the camera. To do this,
move the joystick left/right
to select Active.
When establishing a connection between the camera
and an active digital video
unit such as a PC the
unit itself will activate and
deactivate the image transmission.
8.2 Menu system
8.2.5.6
Power
10392703;2
Figure 8.57 Power Setup dialog box

Figure 8.58 Explanations of the Power Setup dialog box
Label
Value
Auto power off
Display power off
LCD illumination
Comments
None
10 min

specify the time after which the
camera will be switched off if
it is not used.
None
30 sec
60 sec

specify the time after which the
display will be switched off if it
is not used.
Low
Medium
High

specify the level of background
illumination of the LCD.
NOTE: For protective reasons, the LCD will be switched off if the detector temperature exceeds +60C
(+149F) and the camera will be switched off if the detector temperature exceeds +68C (+154.4F)
8.2.5.7
Status bar
10392803;2
Figure 8.59 Status bar dialog box
75
8.2 Menu system

Figure 8.60 Explanations of the Status bar dialog box
Label
Value
Date/time
Distance
Emissivity
T Reflected
T Atmosphere
Relative humidity
Range
Lens
Zoom
Text comment
8.2.5.8
Comments
On
Off

enable/disable this label on the
status bar.
On
Off

status bar.
On
Off

status bar.
On
Off

status bar.
On
Off

status bar.
On
Off

status bar.
On
Off

status bar.
On
Off

status bar.
On
Off

status bar.
On
Off

status bar.
Buttons
10393103;2
Figure 8.61 Buttons Settings dialog box
76
8.2 Menu system

Figure 8.62 Explanations of the Buttons Setting dialog box
Label
Value
F1
F2
+/-
Comments
None
Adjust once
Auto focus
Reverse palette
Next palette
Visual/IR
Update ref temp

specify the function of the F1
button on the left side of the
camera.
None
Adjust once
Auto focus
Reverse palette
Next palette
Visual/IR
Update ref temp

specify the function of the F2
button on the left side of the
camera.
None
Level
Span
Focus

specify the function of the +/button on the left side of the
camera.
SEE ALSO: For more information about buttons and their functions, see section 7.2 Keypad buttons
& functions on page 33.
8.2.5.9
Date/time
10393803;2
Figure 8.63 Date/Time dialog box

Figure 8.64 Explanations of the Date/Time dialog box
Label
Value
Year
19702036
Month
112
Day
1 31
77
8.2 Menu system

Label
Value
Hour
12 a.m.12 p.m.
124
The format depends on the settings in the Local settings dialog

box.
Minute
0059
Second
0059
8.2.5.10
Local settings
10393903;2
Figure 8.65 Local settings dialog box

Figure 8.66 Explanations of the Local settings dialog box
Label
Value
Language
NOTE: The camera program will be restarted when you change
the language. This will take a few seconds.
Video output
Temp unit
Distance unit
Date format
Time format
78
NTSC
PAL
C
F
Feet
Meters
YYYY-MM-DD
YY-MM-DD
MM/DD/YY
DD/MM/YY
24 hour
AM/PM
8.2 Menu system
8.2.5.11
Camera info
The Camera info dialog box shows information about memory usage, battery
status, serial numbers, software revision etc. No changes can be made.
8.2.5.12
Profile
Point to Profile and click Save... to save all current user settings as a user profile.
Once you have saved a profile you can load it again by pointing to Load....
Examples of user settings that are saved in the profile:
Measurement markers
Object parameters
Range
Level & span
Palette
Image settings
Power settings
Date & time
8.2.5.13
Factory default
Point to Factory default and press the joystick to reset the camera to the factory
settings.
NOTE: The camera will be restarted when you restore factory settings. This will take a few seconds.
79
Electrical power system

The cameras electrical power system consists of the following parts:
a removable battery
a power supply
an internal battery charger
a stand-alone, external battery charger
The camera may powered either by using the battery, or by using the power
supply. When using the power supply, the battery will if its inserted in the battery
compartment automatically be charged. You can still use the camera during
charging.
The camera is shipped with charged batteries. To increase the battery life, the battery should be
fully discharged and charged a couple of times. You can do this by using the camera until the
battery is fully depleted.
The same power supply can be used for both the internal battery charger and the external battery
charger.
The operation time of the camera when run on a battery is substantially shorter in low temperatures.
The removable battery gives an operation time of approx. 1.52 hours. When
Battery low is displayed on the screen it is time to charge the battery.
9.1
Internal battery charging
To charge the battery internally, follow the instructions below.
80
Step
Action
Make sure that the battery is correctly inserted into the camera.
Connect the power supply cable to the camera.
The message Charging battery will appear on the screen.
While charging, the battery status symbol will pulse until the battery is fully
charged.
9.2 External battery charging
9.2
External battery charging
10345803;3
Figure 9.1 Stand-alone battery charger
The battery status while charging is indicated by a number of LEDs. See the figure
below.
10346203;4
Figure 9.2 LED indicators on the stand-alone battery charger.

Figure 9.3 LED indicators explanations
Situation
Indicator #
Color & mode
The charger is under power,

but no battery is inserted
Fixed red light
The charger is under power,

and a battery is inserted
Fixed green light
The battery is too cold or too

warm
Flashing green light
81
9.3 Battery safety warnings

Situation
Indicator #
Color & mode
The battery is out of order
Flashing red light
The battery is now being

charged
5 to 2
Pulsing green light from LED 5

to LED 2
Each LED represents 25% battery capacity and will be
switched on accordingly.
9.3
82
Battery safety warnings

Do not place the battery in fire or heat the battery.
Do not install the battery backwards so that the polarity is reversed.
Do not connect the positive terminal and the negative terminal of the battery
to each other with any metal object (such as wire).
Do not pierce the battery with nails, strike the battery with a hammer, step on
the battery, or otherwise subject it to strong impacts or shocks.
Do not solder directly onto the battery.
Do not expose the battery to water or salt water, or allow the battery to get
wet.
Do not disassemble or modify the battery. The battery contains safety and
protection devices which, if damaged, may cause the battery to generate heat,
explode or ignite.
Do not place the battery on or near fires, stoves, or other high-temperature locations.
When the battery is worn out, insulate the terminals with adhesive tape or
similar materials before disposal.
Immediately discontinue use of the battery if, while using, charging, or storing
the battery, the battery emits an unusual smell, feels hot, changes color, changes
shape, or appears abnormal in any other way. Contact your sales location if any
of these problems are observed.
In the event that the battery leaks and the fluid gets into ones eye, do not rub
the eye. Rinse well with water and immediately seek medical care. If left untreated the battery fluid could cause damage to the eye.
When charging the battery, only use a specified battery charger.
Do not attach the batteries to a power supply plug or directly to a cars cigarette
lighter.
Do not place the batteries in or near fire, or into direct sunlight. When the battery
becomes hot, the built-in safety equipment is activated, preventing the battery
from charging further, and heating the battery can destroy the safety equipment
and can cause additional heating, breaking, or ignition of the battery.
Do not continue charging the battery if it does not recharge within the specified
charging time. Doing so may cause the battery to become hot, explode, or ignite.
9.3 Battery safety warnings
The temperature range over which the battery can be charged is 0+45C
(+32+113F). Charging the battery at temperatures outside of this range may
cause the battery to become hot or to break. Charging the battery outside of
this temperature range may also harm the performance of the battery or reduce
the batterys life expectancy.
Do not discharge the battery using any device except for the specified device.
When the battery is used in devices aside from the specified device it may
damage the performance of the battery or reduce its life expectancy, and if the
device causes an abnormal current to flow, it may cause the battery to become
hot, explode, or ignite and cause serious injury.
The temperature range over which the battery can be discharged is -15+45C
(+18.8+113F). Use of the battery outside of this temperature range may
damage the performance of the battery or may reduce its life expectancy.
83
10
A note on LEMO connectors
10.1
How to connect & disconnect LEMO connectors
The male LEMO connectors used on the camera cables are designed to lock securely to the female connectors on the camera body. A connector consists of a
fixed inner tube and a sliding outer tube. The outer tube controls the locking
teeth. To unlock the connector, pull the outer tube in the indicated direction. See
the figure below
NOTE: Never pull the cable.
10062403;2
Figure 10.1 Straight body LEMO connector.
84
Callout
Description
Locking teeth
Sliding outer tube
Fixed inner tube
10.1 How to connect & disconnect LEMO connectors

10403003;1
Figure 10.2 Unlocking a LEMO connector
85
11
Maintenance & cleaning
11.1
Camera body, cables & accessories
The camera body, cables and accessories may be cleaned by wiping with a soft
cloth. To remove stains, wipe with a soft cloth moistened with a mild detergent
solution and wrung dry, then wipe with a dry soft cloth.
Do not use benzene, thinner, or any other chemical product on the camera, the
cables or the accessories, as this may cause deterioration.
11.2
Lenses
All lenses are coated with an anti-reflective coating and care must be taken when
cleaning them. Cotton wool soaked in 96% ethyl alcohol (C2H5OH) may be used
to clean the lenses. The lenses should be wiped once with the solution, then the
cotton wool should be discarded.
If ethyl alcohol is unavailable, DEE (i.e. ether = diethylether, C4H10O) may be used
for cleaning.
Sometimes drying marks may appear on the lenses. To prevent this, a cleaning
solution of 50% acetone (i.e. dimethylketone, (CH3)2CO)) and 50% ethyl alcohol
(C2H5OH) may be used.
Please note the following:
86
Excessive cleaning of the lenses may wear down the coating.

The chemical substances described in this section may be dangerous. Carefully
read all warning labels on containers before using the substances, as well as
applicable MSDS (Material Safety Data Sheets).
12
Troubleshooting
Problem
Possible reason
Solution
The LCD on the remote

control, or the viewfinder,
displays no image at all.
The camera may have been switched off

automatically due the settings in the
Power setup dialog box.
Press ON/OFF to switch on

the camera.
The LCD may have been switched off

automatically due to the settings in the
Power setup dialog box.
Press ON/OFF to switch on

the camera.
The connector on the remote control cable may not be properly inserted into the
remote control connector camera.
Verify that the connector

on the remote control cable is properly inserted.
There is no battery in the battery compartment.
Insert a fully charged battery.
There is a battery in the battery compartment, but the battery is depleted.
Charge the battery.
If you are using the power supply, the

power supply connector may not be
properly inserted into the power connector on the camera.
Verify that the power supply connector is properly

inserted.

mains plug may not be properly plugged
in into a mains supply.
Verify that the mains plug

is properly plugged in.

mains cable may not be properly
plugged in into the power supply.
Verify that the mains cable is properly plugged in.
The level needs to be changed.
Change the level.
The span needs to be changed
Change the span.
The camera needs to be autoadjusted.
Autoadjust the camera.
The target may be hotter or colder than

the temperature range you are currently
using.
Change the range.
A different palette may be more suitable

for imaging the target than the one you
are currently using.
Change the palette.
The LCD/viewfinder displays an image, but it is of

poor quality.
87
Problem
Possible reason
Solution
The LCD/viewfinder displays an infrared image,

but it is blurry.
The target may be out of focus.
Focus the camera by

pressing and holding
down the A button for a
few seconds.
The ocular diopter adjustment of the

viewfinder may be incorrect.
Change the ocular diopter

adjustment by rotating
the adjustment knob on
the bottom side of the
viewfinder.
The LCD/viewfinder displays a visual image, but

it is blurry.
The target may be out of focus.
Focus the visual camera

by rotating the focus ring
on the visual camera.
The LCD/viewfinder displays an image, but it is of

low illumination.
The illumination of the LCD may have

accidentally been set to too low a value.
Change the illumination

of the LCD.
When connecting the infrared camera to an external video monitor, no image appears.
The video cable connector may not be

properly inserted into the video connector on the camera.
Verify that the video cable

connector is properly inserted.
The video cable connector may not be

properly inserted into the video connector on the external monitor.
Verify that the video cable

connector is properly inserted.
The camera may have accidentally been

set to PAL video format, while the external video monitor will only display NTSC
video format, and vice versa.
Change the video format.
The internal flash memory may be full.
To be able to save more

images, download the
images to your computer
using ThermaCAM QuickView.
The CompactFlash card may be full.
To be able to save more

images, move the images
from the CompactFlash
card by downloading
them to your computer
using ThermaCAM QuickView, or replace the card
with an empty card.
The camera may have accidentally been

set to the wrong date & time.
Change the date & time.
It is not possible to store

any more images in the
camera.
The LCD/viewfinder does

not display the correct
date & time.
88
13
Technical specifications &

dimensional drawings
NOTE: FLIR Systems reserves the right to discontinue models, parts and accessories, and other items,
or change specifications at any time without prior notice.
13.1
Imaging performance
Field of view/min. focus distance
24 18/0.3m (0.98ft)
Spatial resolution
1.3mrad
Image frequency
50/60Hz, non-interlaced
Electronic zoom function
2x, 4x, 8x interpolating
Focus
Automatic or manual
Digital image enhancement
Adaptive digital noise reduction
Built-in digital video
640 480 pixels, full color
13.2
Detector
Type
Focal Plane Array (FPA), uncooled microbolometer,

320 240 pixels
Spectral range
13.3
7.513m
Image presentation
Viewfinder
Built-in, high resolution color LCD (TFT)
LCD on remote control
4"
89
13.4 Temperature ranges
13.4
Temperature ranges
Temperature range, standard
-40+120C (-40+248F)
-10+55C (+14+131F)
0+500C (+32+932F)

configuration, one or several of these ranges
may be disabled.
Temperature range, extra options
+350+1500C (+662+2732F)
+350+2000C (+662+3632F)
Accuracy
2C/ 3.6F or 2% of reading
Emissivity correction
Set by number, or by selection in predefined list
Atmospheric transmission correction
Automatic, based on input from distance, atmospheric temperature, and relative humidity.
Optics transmission correction
Automatic, based on signals from internal sensors
Reflected ambient temperature correction
Yes
External optics correction
Yes
13.5
Classification
Class 2
Type
Semiconductor AlGaInP diode laser, 1 mW / 635

nm (red)
13.6
90
Laser LocatIR
Electrical power system
Battery type
Rechargeable Li/Ion battery
Battery operating time
1.52 hours. Display shows battery status
Battery charging
In camera (AC adapter) or stand-alone 2-bay

charger
AC operation
AC adapter, 90260 VAC, 50/60 Hz, 12 VDC out
Voltage
916 VDC (1116 VDC when charging)
13.7 Environmental specifications

Power management
User-selectable:
13.7
automatic shut-down
stand-by
sleep and
deep-sleep mode
Environmental specifications
Operating temperature range
-15+50C (+5+122F)
Storage temperature range
-40+70C (-40+158F)
Humidity
Operating & storage:1095%, non-condensing,
Encapsulation
IP54 (IEC529)
Shock
25g, IEC68-2-29
Vibration
2g, IEC68-2-6
13.8
Physical specifications
Weight
2.0 kg (4.41 lb) incl. battery & remote control
Size (L W H)
234 124 161 mm (9.21 4.88 6.34")
Tripod mounting
Standard, 1/4"-20
13.9
Interfaces & connectors
Computer interfaces
USB Rev 2.0 (full speed)

RS-232 (extra option)
FireWire (IEEE 1394a, 100/200/400 Mbps)
Audio input/output
Headset connection for voice annotation of images
Interface for integrated LCD & remote control
Yes
Power input
916 VDC (1116 VDC when charging), standard

2.5 mm DC connector. Polarity protected
CVBS
Standard RCA connector for composite video

CVBS (ITU-R BT.470 PAL/SMPTE 170M NTSC)
IrDA
Infrared communications link (IrDA 1.4 SIR, Baud

rate 115 kBaud)
91
13.10 Pin configurations
13.10
Pin configurations
13.10.1
Headset connector
10402603;1
Figure 13.1 Pin configuration for headset connector (on camera operators side)
Connector type:
LEMO 05B, 5 pins
Signal name
Type
Pin number
SPEAK_R
OUT
GNDD
GND
MIC_POS
IN
GNDD
GND
SPEAK_L
OUT
10563003;1
Figure 13.2 Graphical representation of alarm output signal. The alarm output signal is a 1 kHz signal
with an amplitude of 2 Vpp (load 1k). The signal can drive loads as low as 16 . The signal is available
in pin 1 of the headset connector.
92
13.10.2
RS-232/USB connector
10402703;1
Figure 13.3 Pin configuration for RS-232/USB connector (on camera operators side)
Connector type:
LEMO 1B, 6 pins
Signal name
Type
Pin number
USB_D+
I/O
USB_D-
I/O
USB_POWER
OUT
GND
GND
RS232_TX1
OUT
RS232_RX1
IN
10563403;1
Figure 13.4 Video lamp, to be inserted in the RS-232/USB connector
Power: 0.7 W
Voltage: 5 V 10%
Luminous intensity: 35000mcd in the middle of the light beam; 20000mcd
measured at an angle of 10 from the light beam, and 5000mcd measured
at an angle of 20 from the light beam.
93

Connector type:
LEMO 1B, 6 pins. The video lamp uses the same connector as
the RS-232/USB signal (see figure 13.3 on page 93).
Signal name
Type
Pin number
POWER
OUT
GND
GND
13.10.3
Remote control connector
10402803;1
Figure 13.5 Pin configuration for remote control connector (on camera operators side)
94
Connector type:
LEMO 1B, 8 pins
Signal name
Type
Pin number
P8VA
POWER
SCL_D
I/O
GNDD
GND
LVDS_DISP-
OUT
LVDS_DISP+
OUT
GNDD
GND
SDA_D
I/O
P8VA
POWER
13.10.4
Power connector
10402503;1
Figure 13.6 Pin configuration for power connector (on camera operators side). A: Center pin; B:
Chassis
Connector type:
2.5 mm DC
Signal name
Type
Pin number
+12V
POWER
CENTER PIN
GND
POWER
CHASSIS
13.10.5
CVBS connector
10402503;1
Figure 13.7 Pin configuration for CVBS connector (on camera operators side). A: Center pin; B:
Chassis
Connector type:
RCA/PHONO
Signal name
Type
Pin number
CVBS
VIDEO
CENTER PIN
GND
POWER
CHASSIS
13.10.6
FireWire connector
10402303;1
Figure 13.8 Pin configuration for FireWire connector (on camera operators side)
95
13.11 Relationship between fields of view and distance

Connector type:
FireWire, 4 pins
Signal name
Type
Pin number
TPB0-
OUT
TPB0+
OUT
TPA0-
IN
TPA1+
IN
13.11
Relationship between fields of view and distance
10401803;1
Figure 13.9 Relationship between fields of view and distance. 1: Distance to target; 2: VFOV = vertical
field of view; 3: HFOV = horizontal field of view, 4: IFOV = instantaneous field of view (spot size).
Figure 13.10 Horizontal, vertical and instantaneous fields of view for certain distances to targets. D
= distance to target.
96
1.20
5.00
10.00
25.00
50.00
100.00
3.90
16.40
32.80
82.00
164.00
327.90
ft.
HFOV
0.61
1.22
3.06
6.12
12.23
HFOV
2.01
4.01
10.03
20.05
40.11
ft.
VFOV
0.46
0.92
2.29
4.59
9.17
VFOV
1.50
3.01
7.52
15.04
30.08
ft.
IFOV
1.91
3.82
9.56
19.11
38.23
mm
IFOV
0.08
0.15
0.38
0.75
1.50
in.
12
HFOV
0.25
1.05
2.10
5.26
10.51
21.02
12
HFOV
0.83
3.45
6.89
17.23
34.46
68.92
ft.

D
1.20
5.00
10.00
25.00
50.00
100.00
3.90
16.40
32.80
82.00
164.00
327.90
ft.
12
VFOV
0.19
0.79
1.58
3.94
7.88
15.77
12
VFOV
0.62
2.58
5.17
12.92
25.85
51.69
ft.
12
IFOV
0.79
3.28
6.57
16.42
32.85
65.69
mm
12
IFOV
0.03
0.13
0.26
0.65
1.29
2.59
in.
24
HFOV
0.51
2.13
4.25
10.63
21.26
42.51
24
HFOV
1.67
6.97
13.94
34.85
69.69
139.38
ft.
24
VFOV
0.38
1.59
3.19
7.97
15.94
31.88
m.
24
VFOV
1.25
5.23
10.45
26.13
52.27
104.54
ft.
24
IFOV
1.59
6.64
13.28
33.21
66.42
132.85
mm
24
IFOV
0.06
0.26
0.52
1.31
2.62
5.23
in.
45
HFOV
0.99
4.14
8.28
20.71
41.42
82.84
45
HFOV
3.26
13.58
27.16
67.90
135.81
271.62
ft.
45
VFOV
0.75
3.11
6.21
15.53
31.07
62.13
45
VFOV
2.44
10.19
20.37
50.93
101.86
203.71
ft.
45
IFOV
3.11
12.94
25.89
64.72
129.44
258.88
mm
45
IFOV
0.12
0.51
1.02
2.55
5.10
10.19
in.
65
HFOV
1.53
6.37
12.74
31.85
63.71
127.41
65
HFOV
5.01
20.89
41.78
104.44
208.88
417.75
ft.
65
VFOV
1.15
4.78
9.56
23.89
47.78
95.56
65
VFOV
3.76
15.67
31.33
78.33
156.66
313.31
ft.
65
IFOV
4.78
19.91
39.82
99.54
199.08
398.17
mm
65
IFOV
0.19
0.78
1.57
3.92
7.84
15.68
in.
80
HFOV
2.01
8.39
16.78
41.95
83.91
167.82
80
HFOV
6.60
27.51
55.02
137.56
275.11
550.23
ft.
80
VFOV
1.51
6.29
12.59
31.47
62.93
125.86
97

D
1.20
5.00
10.00
25.00
50.00
100.00
3.90
16.40
32.80
82.00
164.00
327.90
ft.
80
VFOV
4.95
20.63
41.27
103.17
206.34
412.67
ft.
80
IFOV
6.29
26.22
52.44
131.11
262.22
524.44
mm
80
IFOV
0.25
1.03
2.06
5.16
10.31
20.65
in.
Figure 13.11 F-number and close focus limits for various lenses
98
Lens
12
24
45
65
80
Close focus limit (m)
1.2
0.3
0.1
0.2
0.15
Close focus limit (ft.)
13.11
3.93
0.98
0.32
0.64
0.49
f-number
1.0
1.0
1.0
1.0
1.5
1.0
13.12 Basic dimensions battery charger
13.12
Basic dimensions battery charger
10388003;3
Figure 13.12 Overall dimensions of the battery charger
99
13.13 Basic dimensions battery
13.13
Basic dimensions battery
10388103;3
Figure 13.13 Overall dimensions of the battery
100
13.14 Basic dimensions remote control
13.14
Basic dimensions remote control
10394003;3
Figure 13.14 Overall dimensions of the remote control
101
13.15 Basic dimensions camera
13.15
Basic dimensions camera
10346503;3
Figure 13.15 Overall dimensions of the camera
102
13.16
10563203;1
Figure 13.16 Overall dimensions of the camera, when the video lamp is mounted
103
13.17 Basic dimensions video lamp
13.17
Basic dimensions video lamp
10563303;1
Figure 13.17 Overall dimensions of the video lamp
104
13.18
10352203;3
Figure 13.18 Location of the standard tripod mount (1/4"-20) on the bottom side of the camera
105
14
Glossary
Figure 14.1 Glossary of common infrared terms & expressions
106
Term or expression
Explanation
absorption (absorption factor)
The amount of radiation absorbed by an object relative to

the received radiation. A number between 0 and 1.
ambient
Objects and gases that emit radiation towards the object

being measured.
atmosphere
The gases between the object being measured and the

camera, normally air.
autoadjust
A function making a camera perform an internal image correction.
autopalette
The IR image is shown with an uneven spread of colors, displaying cold objects as well as hot ones at the same time.
blackbody
Totally non-reflective object. All its radiation is due to its own

temperature.
blackbody radiator
An IR radiating equipment with blackbody properties used

to calibrate IR cameras.
calculated atmospheric transmission
A transmission value computed from the temperature, the

relative humidity of air and the distance to the object.
cavity radiator
A bottle shaped radiator with an absorbing inside, viewed

through the bottleneck.
color temperature
The temperature for which the color of a blackbody matches

a specific color.
conduction
The process that makes heat spread into a material.
continuous adjust
A function that adjusts the image. The function works all the
time, continuously adjusting brightness and contrast according to the image content.
convection
The process that makes hot air or liquid rise.
difference temperature
A value which is the result of a subtraction between two

temperature values.
dual isotherm
An isotherm with two color bands, instead of one.
emissivity (emissivity factor)
The amount of radiation coming from an object, compared

to that of a blackbody. A number between 0 and 1.
Term or expression
Explanation
emittance
Amount of energy emitted from an object per unit of time

and area (W/m2)
estimated atmospheric transmission
A transmission value, supplied by a user, replacing a calculated one
external optics
Extra lenses, filters, heat shields etc. that can be put between
the camera and the object being measured.
filter
A material transparent only to some of the infrared wavelengths.
FOV
Field of view: The horizontal angle that can be viewed

through an IR lens.
FPA
Focal plane array: A type of IR detector.
graybody
An object that emits a fixed fraction of the amount of energy

of a blackbody for each wavelength.
IFOV
Instantaneous field of view: A measure of the geometrical

resolution of an IR camera.
image correction (internal or external)
A way of compensating for sensitivity differences in various

parts of live images and also of stabilizing the camera.
infrared
Non-visible radiation, having a wavelength from about 213

m.
IR
infrared
isotherm
A function highlighting those parts of an image that fall

above, below or between one or more temperature intervals.
isothermal cavity
A bottle-shaped radiator with a uniform temperature viewed

through the bottleneck.
Laser LocatIR
An electrically powered light source on the camera that emits

laser radiation in a thin, concentrated beam to point at certain
parts of the object in front of the camera.
laser pointer
An electrically powered light source on the camera that emits

laser radiation in a thin, concentrated beam to point at certain
parts of the object in front of the camera.
level
The center value of the temperature scale, usually expressed

as a signal value.
manual adjust
A way to adjust the image by manually changing certain

parameters.
107
Term or expression
Explanation
NETD
Noise equivalent temperature difference. A measure of the

image noise level of an IR camera.
noise
Undesired small disturbance in the infrared image
object parameters
A set of values describing the circumstances under which

the measurement of an object was made, and the object itself
(such as emissivity, ambient temperature, distance etc.)
object signal
A non-calibrated value related to the amount of radiation

received by the camera from the object.
palette
The set of colors used to display an IR image.
pixel
Stands for picture element. One single spot in an image.
radiance
Amount of energy emitted from an object per unit of time,

area and angle (W/m2/sr)
radiant power
Amount of energy emitted from an object per unit of time

(W)
radiation
The process by which electromagnetic energy, is emitted by

an object or a gas.
radiator
A piece of IR radiating equipment.
range
The current overall temperature measurement limitation of

an IR camera. Cameras can have several ranges. Expressed
as two blackbody temperatures that limit the current calibration.
reference temperature
A temperature which the ordinary measured values can be

compared with.
reflection
The amount of radiation reflected by an object relative to

the received radiation. A number between 0 and 1.
relative humidity
Percentage of water in the air, relative to what is physically

possible. Air temperature dependent.
saturation color
The areas that contain temperatures outside the present

level/span settings are colored with the saturation colors.
The saturation colors contain an overflow color and an underflow color.
There is also a third red saturation color that marks everything
saturated by the detector indicating that the range should
probably be changed.
108
Term or expression
Explanation
span
The interval of the temperature scale, usually expressed as

a signal value.
spectral (radiant) emittance
Amount of energy emitted from an object per unit of time,

area and wavelength (W/m2/m)
temperature range
The current overall temperature measurement limitation of

an IR camera. Cameras can have several ranges. Expressed
as two blackbody temperatures that limit the current calibration.
temperature scale
The way in which an IR image currently is displayed. Expressed as two temperature values limiting the colors.
thermogram
infrared image
transmission (or transmittance)

factor
Gases and materials can be more or less transparent. Transmission is the amount of IR radiation passing through them.
A number between 0 and 1.
transparent isotherm
An isotherm showing a linear spread of colors, instead of

covering the highlighted parts of the image.
visual
Refers to the video mode of a IR camera, as opposed to the

normal, thermographic mode. When a camera is in video
mode it captures ordinary video images, while thermographic
images are captured when the camera is in IR mode.
109
15
Thermographic measurement
techniques
15.1
Introduction
An infrared camera measures and images the emitted infrared radiation from an
object. The fact that radiation is a function of object surface temperature makes
it possible for the camera to calculate and display this temperature.
However, the radiation measured by the camera does not only depend on the
temperature of the object but is also a function of the emissivity. Radiation also
originates from the surroundings and is reflected in the object. The radiation from
the object and the reflected radiation will also be influenced by the absorption
of the atmosphere.
To measure temperature accurately, it is therefore necessary to compensate for
the effects of a number of different radiation sources. This is done on-line automatically by the camera. The following object parameters must, however, be
supplied for the camera:
The emissivity of the object

The reflected temperature
The distance between the object and the camera
The relative humidity
15.2
Emissivity
The most important object parameter to set correctly is the emissivity which, in
short, is a measure of how much radiation is emitted from the object, compared
to that from a perfect blackbody.
Normally, object materials and surface treatments exhibit emissivity ranging from
approximately 0.1 to 0.95. A highly polished (mirror) surface falls below 0.1, while
an oxidized or painted surface has much higher emissivity. Oil-based paint, regardless of color in the visible spectrum, has an emissivity over 0.9 in the infrared. Human skin exhibits an emissivity close to 1.
Non-oxidized metals represent an extreme case of almost perfect opacity and
high spectral reflexivity, which does not vary greatly with wavelength. Consequently, the emissivity of metals is low only increasing with temperature. For nonmetals, emissivity tends to be high, and decreases with temperature.
110
15.3 Reflected ambient temperature
15.2.1
Finding the emissivity of an object
15.2.1.1
Using a thermocouple
Select a reference point and measure its temperature using a thermocouple. Alter
the emissivity until the temperature measured by the camera agrees with the
thermocouple reading. This is the emissivity value of the reference object. However, the temperature of the reference object must not be too close to the ambient
temperature for this to work.
15.2.1.2
Using reference emissivity
A tape or paint of a known emissivity should be put onto the object. Measure the
temperature of the tape/paint using the camera, setting emissivity to the correct
value. Note the temperature. Alter emissivity, until the area with the unknown
emissivity adjacent to the tape/paint has the same temperature reading. The
emissivity value can now be read. The temperature of the reference object must
not be too close to the ambient temperature for this to work either.
15.3
Reflected ambient temperature
This parameter is used to compensate for the radiation reflected in the object and
the radiation emitted from the atmosphere between the camera and the object.
If the emissivity is low, the distance very long and the object temperature relatively
close to that of the ambient it will be important to set and compensate for the
ambient temperature correctly.
111
16
History of infrared technology
Less than 200 years ago the existence of the infrared portion of the electromagnetic spectrum wasn't even suspected. The original significance of the infrared
spectrum, or simply the infrared as it is often called, as a form of heat radiation
is perhaps less obvious today than it was at the time of its discovery by Herschel
in 1800.
10398703;1
Figure 16.1 Sir William Herschel (17381822)
The discovery was made accidentally during the search for a new optical material.
Sir William Herschel Royal Astronomer to King George III of England, and already
famous for his discovery of the planet Uranus was searching for an optical filter
material to reduce the brightness of the suns image in telescopes during solar
observations. While testing different samples of colored glass which gave similar
reductions in brightness he was intrigued to find that some of the samples passed
very little of the suns heat, while others passed so much heat that he risked eye
damage after only a few seconds observation.
Herschel was soon convinced of the necessity of setting up a systematic experiment, with the objective of finding a single material that would give the desired
reduction in brightness as well as the maximum reduction in heat. He began the
experiment by actually repeating Newtons prism experiment, but looking for the
heating effect rather than the visual distribution of intensity in the spectrum. He
first blackened the bulb of a sensitive mercury-in-glass thermometer with ink, and
with this as his radiation detector he proceeded to test the heating effect of the
various colors of the spectrum formed on the top of a table by passing sunlight
through a glass prism. Other thermometers, placed outside the suns rays, served
as controls.
As the blackened thermometer was moved slowly along the colors of the spectrum,
the temperature readings showed a steady increase from the violet end to the
red end. This was not entirely unexpected, since the Italian researcher, Landriani,
112
in a similar experiment in 1777 had observed much the same effect. It was Herschel,
however, who was the first to recognize that there must be a point where the
heating effect reaches a maximum, and that measurements confined to the visible
portion of the spectrum failed to locate this point.
10398903;1
Figure 16.2 Marsilio Landriani (17461815)
Moving the thermometer into the dark region beyond the red end of the spectrum,
Herschel confirmed that the heating continued to increase. The maximum point,
when he found it, lay well beyond the red end in what is known today as the
infrared wavelengths.
When Herschel revealed his discovery, he referred to this new portion of the
electromagnetic spectrum as the thermometrical spectrum. The radiation itself
he sometimes referred to as dark heat, or simply the invisible rays. Ironically,
and contrary to popular opinion, it wasn't Herschel who originated the term infrared. The word only began to appear in print around 75 years later, and it is still
unclear who should receive credit as the originator.
Herschels use of glass in the prism of his original experiment led to some early
controversies with his contemporaries about the actual existence of the infrared
wavelengths. Different investigators, in attempting to confirm his work, used
various types of glass indiscriminately, having different transparencies in the infrared. Through his later experiments, Herschel was aware of the limited transparency of glass to the newly-discovered thermal radiation, and he was forced to
conclude that optics for the infrared would probably be doomed to the use of
reflective elements exclusively (i.e. plane and curved mirrors). Fortunately, this
proved to be true only until 1830, when the Italian investigator, Melloni, made his
great discovery that naturally occurring rock salt (NaCl) which was available in
large enough natural crystals to be made into lenses and prisms is remarkably
transparent to the infrared. The result was that rock salt became the principal infrared optical material, and remained so for the next hundred years, until the art
of synthetic crystal growing was mastered in the 1930s.
113
10399103;1
Figure 16.3 Macedonio Melloni (17981854)
Thermometers, as radiation detectors, remained unchallenged until 1829, the

year Nobili invented the thermocouple. (Herschels own thermometer could be
read to 0.2C (0.036F), and later models were able to be read to 0.05C (0.09F)).
Then a breakthrough occurred; Melloni connected a number of thermocouples
in series to form the first thermopile. The new device was at least 40 times as
sensitive as the best thermometer of the day for detecting heat radiation capable
of detecting the heat from a person standing three meters away.
The first so-called heat-picture became possible in 1840, the result of work by
Sir John Herschel, son of the discoverer of the infrared and a famous astronomer
in his own right. Based upon the differential evaporation of a thin film of oil when
exposed to a heat pattern focused upon it, the thermal image could be seen by
reflected light where the interference effects of the oil film made the image visible
to the eye. Sir John also managed to obtain a primitive record of the thermal image
on paper, which he called a thermograph.
10399003;1
Figure 16.4 Samuel P. Langley (18341906)
The improvement of infrared-detector sensitivity progressed slowly. Another

major breakthrough, made by Langley in 1880, was the invention of the bolometer.
114
This consisted of a thin blackened strip of platinum connected in one arm of a

Wheatstone bridge circuit upon which the infrared radiation was focused and to
which a sensitive galvanometer responded. This instrument is said to have been
able to detect the heat from a cow at a distance of 400 meters.
An English scientist, Sir James Dewar, first introduced the use of liquefied gases
as cooling agents (such as liquid nitrogen with a temperature of -196C (-320.8F))
in low temperature research. In 1892 he invented a unique vacuum insulating
container in which it is possible to store liquefied gases for entire days. The common thermos bottle, used for storing hot and cold drinks, is based upon his invention.
Between the years 1900 and 1920, the inventors of the world discovered the infrared. Many patents were issued for devices to detect personnel, artillery, aircraft,
ships and even icebergs. The first operating systems, in the modern sense, began
to be developed during the 191418 war, when both sides had research programs
devoted to the military exploitation of the infrared. These programs included experimental systems for enemy intrusion/detection, remote temperature sensing,
secure communications, and flying torpedo guidance. An infrared search system
tested during this period was able to detect an approaching airplane at a distance
of 1.5 km (0.94 miles), or a person more than 300 meters (984 ft.) away.
The most sensitive systems up to this time were all based upon variations of the
bolometer idea, but the period between the two wars saw the development of
two revolutionary new infrared detectors: the image converter and the photon
detector. At first, the image converter received the greatest attention by the military, because it enabled an observer for the first time in history to literally see in
the dark. However, the sensitivity of the image converter was limited to the near
infrared wavelengths, and the most interesting military targets (i.e. enemy soldiers)
had to be illuminated by infrared search beams. Since this involved the risk of
giving away the observers position to a similarly-equipped enemy observer, it is
understandable that military interest in the image converter eventually faded.
The tactical military disadvantages of so-called 'active (i.e. search beam-equipped)
thermal imaging systems provided impetus following the 193945 war for extensive secret military infrared-research programs into the possibilities of developing
passive (no search beam) systems around the extremely sensitive photon detector.
During this period, military secrecy regulations completely prevented disclosure
of the status of infrared-imaging technology. This secrecy only began to be lifted
in the middle of the 1950s, and from that time adequate thermal-imaging devices
finally began to be available to civilian science and industry.
115
17
Theory of thermography
17.1
Introduction
The subjects of infrared radiation and the related technique of thermography are
still new to many who will use an infrared camera. In this section the theory behind
thermography will be given.
17.2
The electromagnetic spectrum
The electromagnetic spectrum is divided arbitrarily into a number of wavelength

regions, called bands, distinguished by the methods used to produce and detect
the radiation. There is no fundamental difference between radiation in the different
bands of the electromagnetic spectrum. They are all governed by the same laws
and the only differences are those due to differences in wavelength.
10067803;1
Figure 17.1 The electromagnetic spectrum. 1: X-ray; 2: UV; 3: Visible; 4: IR; 5: Microwaves; 6: Radiowaves.
Thermography makes use of the infrared spectral band. At the short-wavelength

end the boundary lies at the limit of visual perception, in the deep red. At the
long-wavelength end it merges with the microwave radio wavelengths, in the
millimeter range.
The infrared band is often further subdivided into four smaller bands, the
boundaries of which are also arbitrarily chosen. They include: the near infrared
116
17.3 Blackbody radiation
(0.753 m), the middle infrared (36 m), the far infrared (615 m) and the extreme
infrared (15100 m). Although the wavelengths are given in m (micrometers),
other units are often still used to measure wavelength in this spectral region, e.g.
nanometer (nm) and ngstrm ().
The relationships between the different wavelength measurements is:
17.3
Blackbody radiation
A blackbody is defined as an object which absorbs all radiation that impinges on

it at any wavelength. The apparent misnomer black relating to an object emitting
radiation is explained by Kirchhoffs Law (after Gustav Robert Kirchhoff, 18241887),
which states that a body capable of absorbing all radiation at any wavelength is
equally capable in the emission of radiation.
10398803;1
Figure 17.2 Gustav Robert Kirchhoff (18241887)
The construction of a blackbody source is, in principle, very simple. The radiation
characteristics of an aperture in an isotherm cavity made of an opaque absorbing
material represents almost exactly the properties of a blackbody. A practical application of the principle to the construction of a perfect absorber of radiation
consists of a box that is light tight except for an aperture in one of the sides. Any
radiation which then enters the hole is scattered and absorbed by repeated reflections so only an infinitesimal fraction can possibly escape. The blackness which is
obtained at the aperture is nearly equal to a blackbody and almost perfect for all
wavelengths.
By providing such an isothermal cavity with a suitable heater it becomes what is
termed a cavity radiator. An isothermal cavity heated to a uniform temperature
generates blackbody radiation, the characteristics of which are determined solely
by the temperature of the cavity. Such cavity radiators are commonly used as
117
sources of radiation in temperature reference standards in the laboratory for calibrating thermographic instruments, such as a FLIR Systems camera for example.
If the temperature of blackbody radiation increases to more than 525C (977F),
the source begins to be visible so that it appears to the eye no longer black. This
is the incipient red heat temperature of the radiator, which then becomes orange
or yellow as the temperature increases further. In fact, the definition of the socalled color temperature of an object is the temperature to which a blackbody
would have to be heated to have the same appearance.
Now consider three expressions that describe the radiation emitted from a
blackbody.
17.3.1
Plancks law
10399203;1
Figure 17.3 Max Planck (18581947)
Max Planck (18581947) was able to describe the spectral distribution of the radiation from a blackbody by means of the following formula:
where:
118
Wb
Blackbody spectral radiant emittance at wavelength .
Velocity of light = 3 108 m/s
Plancks constant = 6.6 10-34 Joule sec.
Boltzmanns constant = 1.4 10-23 Joule/K.
Absolute temperature (K) of a blackbody.
Wavelength (m).
NOTE: The factor 10-6 is used since spectral emittance in the curves is expressed in Watt/m2m. If the
factor is excluded, the dimension will be Watt/m2m.
Plancks formula, when plotted graphically for various temperatures, produces a

family of curves. Following any particular Planck curve, the spectral emittance is
zero at = 0, then increases rapidly to a maximum at a wavelength max and after
passing it approaches zero again at very long wavelengths. The higher the temperature, the shorter the wavelength at which maximum occurs.
10327103;3
Figure 17.4 Blackbody spectral radiant emittance according to Plancks law, plotted for various absolute
temperatures. 1: Spectral radiant emittance (W/cm2 103(m)); 2: Wavelength (m)
17.3.2
Wiens displacement law
By differentiating Plancks formula with respect to , and finding the maximum,

we have:
This is Wiens formula (after Wilhelm Wien, 18641928), which expresses mathematically the common observation that colors vary from red to orange or yellow
as the temperature of a thermal radiator increases. The wavelength of the color
is the same as the wavelength calculated for max. A good approximation of the
value of max for a given blackbody temperature is obtained by applying the rulePubl. No. 1 557 945 Rev. a43 ENGLISH (EN) April 6, 2004
119
of-thumb 3 000/T m. Thus, a very hot star such as Sirius (11 000 K), emitting
bluish-white light, radiates with the peak of spectral radiant emittance occurring
within the invisible ultraviolet spectrum, at wavelength 0.27 m.
10399403;1
Figure 17.5 Wilhelm Wien (18641928)
The sun (approx. 6 000K) emits yellow light, peaking at about 0.5 m in the middle
of the visible light spectrum.
At room temperature (300K) the peak of radiant emittance lies at 9.7 m, in the
far infrared, while at the temperature of liquid nitrogen (77K) the maximum of
the almost insignificant amount of radiant emittance occurs at 38 m, in the extreme infrared wavelengths.
120

10327203;3
Figure 17.6 Planckian curves plotted on semi-log scales from 100K to 1000K. The dotted line represents the locus of maximum radiant emittance at each temperature as described by Wien's displacement
law. 1: Spectral radiant emittance (W/cm2 (m)); 2: Wavelength (m).
17.3.3
Stefan-Boltzmann's law
By integrating Plancks formula from = 0 to = , we obtain the total radiant

emittance (Wb) of a blackbody:
This is the Stefan-Boltzmann formula (after Josef Stefan, 18351893, and Ludwig
Boltzmann, 18441906), which states that the total emissive power of a blackbody
is proportional to the fourth power of its absolute temperature. Graphically, Wb
represents the area below the Planck curve for a particular temperature. It can be
shown that the radiant emittance in the interval = 0 to max is only 25% of the
total, which represents about the amount of the suns radiation which lies inside
the visible light spectrum.
121

10399303;1
Figure 17.7 Josef Stefan (18351893), and Ludwig Boltzmann (18441906)
Using the Stefan-Boltzmann formula to calculate the power radiated by the human
body, at a temperature of 300K and an external surface area of approx. 2 m2, we
obtain 1 kW. This power loss could not be sustained if it were not for the compensating absorption of radiation from surrounding surfaces, at room temperatures
which do not vary too drastically from the temperature of the body or, of course,
the addition of clothing.
17.3.4
Non-blackbody emitters
So far, only blackbody radiators and blackbody radiation have been discussed.
However, real objects almost never comply with these laws over an extended
wavelength region although they may approach the blackbody behavior in
certain spectral intervals. For example, a certain type of white paint may appear
perfectly white in the visible light spectrum, but becomes distinctly gray at about
2 m, and beyond 3 m it is almost black.
There are three processes which can occur that prevent a real object from acting
like a blackbody: a fraction of the incident radiation may be absorbed, a fraction
may be reflected, and a fraction may be transmitted. Since all of these factors
are more or less wavelength dependent, the subscript is used to imply the
spectral dependence of their definitions. Thus:
The spectral absorptance = the ratio of the spectral radiant power absorbed
by an object to that incident upon it.
The spectral reflectance = the ratio of the spectral radiant power reflected
by an object to that incident upon it.
The spectral transmittance = the ratio of the spectral radiant power transmitted through an object to that incident upon it.
The sum of these three factors must always add up to the whole at any wavelength,
so we have the relation:
For opaque materials = 0 and the relation simplifies to:

122
Another factor, called the emissivity, is required to describe the fraction of the
radiant emittance of a blackbody produced by an object at a specific temperature.
Thus, we have the definition:
The spectral emissivity = the ratio of the spectral radiant power from an object
to that from a blackbody at the same temperature and wavelength.
Expressed mathematically, this can be written as the ratio of the spectral emittance
of the object to that of a blackbody as follows:
Generally speaking, there are three types of radiation source, distinguished by

the ways in which the spectral emittance of each varies with wavelength.
A blackbody, for which = = 1

A graybody, for which = = constant less than 1
A selective radiator, for which varies with wavelength
According to Kirchhoffs law, for any material the spectral emissivity and spectral
absorptance of a body are equal at any specified temperature and wavelength.
That is:
From this we obtain, for an opaque material (since + = 1):
For highly polished materials approaches zero, so that for a perfectly reflecting
material (i.e. a perfect mirror) we have:
For a graybody radiator, the Stefan-Boltzmann formula becomes:
This states that the total emissive power of a graybody is the same as a blackbody
at the same temperature reduced in proportion to the value of from the graybody.
123
17.4 Infrared semi-transparent materials

10401203;1
Figure 17.8 Spectral radiant emittance of three types of radiators. 1: Spectral radiant emittance; 2:
Wavelength; 3: Blackbody; 4: Selective radiator; 5: Graybody.
10327303;3
Figure 17.9 Spectral emissivity of three types of radiators. 1: Spectral emissivity; 2: Wavelength; 3:
Blackbody; 4: Graybody; 5: Selective radiator.
17.4
Infrared semi-transparent materials
Consider now a non-metallic, semi-transparent body let us say, in the form of a

thick flat plate of plastic material. When the plate is heated, radiation generated
within its volume must work its way toward the surfaces through the material in
which it is partially absorbed. Moreover, when it arrives at the surface, some of it
is reflected back into the interior. The back-reflected radiation is again partially
absorbed, but some of it arrives at the other surface, through which most of it
escapes; part of it is reflected back again. Although the progressive reflections
124
17.4 Infrared semi-transparent materials
become weaker and weaker they must all be added up when the total emittance
of the plate is sought. When the resulting geometrical series is summed, the effective emissivity of a semi-transparent plate is obtained as:
When the plate becomes opaque this formula is reduced to the single formula:
This last relation is a particularly convenient one, because it is often easier to

measure reflectance than to measure emissivity directly.
125
18
The measurement formula
As already mentioned, when viewing an object, the camera receives radiation not
only from the object itself. It also collects radiation from the surroundings reflected
via the object surface. Both these radiation contributions become attenuated to
some extent by the atmosphere in the measurement path. To this comes a third
radiation contribution from the atmosphere itself.
This description of the measurement situation, as illustrated in the figure below,
is so far a fairly true description of the real conditions. What has been neglected
could for instance be sun light scattering in the atmosphere or stray radiation
from intense radiation sources outside the field of view. Such disturbances are
difficult to quantify, however, in most cases they are fortunately small enough to
be neglected. In case they are not negligible, the measurement configuration is
likely to be such that the risk for disturbance is obvious, at least to a trained operator. It is then his responsibility to modify the measurement situation to avoid the
disturbance e.g. by changing the viewing direction, shielding off intense radiation
sources etc.
Accepting the description above, we can use the figure below to derive a formula
for the calculation of the object temperature from the calibrated camera output.
10400503;1
Figure 18.1 A schematic representation of the general thermographic measurement situation.1:

Surroundings; 2: Object; 3: Atmosphere; 4: Camera
Assume that the received radiation power W from a blackbody source of temperature Tsource on short distance generates a camera output signal Usource that is
proportional to the power input (power linear camera). We can then write (Equation
1):
126
or, with simplified notation:
where C is a constant.
Should the source be a graybody with emittance , the received radiation would
consequently be Wsource.
We are now ready to write the three collected radiation power terms:
1 Emission from the object = Wobj, where is the emittance of the object and
is the transmittance of the atmosphere. The object temperature is Tobj.
2 Reflected emission from ambient sources = (1 )Wrefl, where (1 ) is the reflectance of the object. The ambient sources have the temperature Trefl.
It has here been assumed that the temperature Trefl is the same for all emitting
surfaces within the halfsphere seen from a point on the object surface. This is of
course sometimes a simplification of the true situation. It is, however, a necessary
simplification in order to derive a workable formula, and Trefl can at least theoretically be given a value that represents an efficient temperature of a complex
surrounding.
Note also that we have assumed that the emittance for the surroundings = 1. This
is correct in accordance with Kirchhoffs law: All radiation impinging on the surrounding surfaces will eventually be absorbed by the same surfaces. Thus the
emittance = 1. (Note though that the latest discussion requires the complete
sphere around the object to be considered.)
3 Emission from the atmosphere = (1 )Watm, where (1 ) is the emittance of
the atmosphere. The temperature of the atmosphere is Tatm.
The total received radiation power can now be written (Equation 2):
We multiply each term by the constant C of Equation 1 and replace the CW

products by the corresponding U according to the same equation, and get
(Equation 3):
Solve Equation 3 for Uobj (Equation 4):

127
This is the general measurement formula used in all the FLIR Systems thermographic equipment. The voltages of the formula are:
Figure 18.2 Voltages
Uobj
Calculated camera output voltage for a blackbody of temperature

Tobj i.e. a voltage that can be directly converted into true requested object temperature.
Utot
Measured camera output voltage for the actual case.
Urefl
Theoretical camera output voltage for a blackbody of temperature

Trefl according to the calibration.
Uatm
Theoretical camera output voltage for a blackbody of temperature

Tatm according to the calibration.
The operator has to supply a number of parameter values for the calculation:
the object emittance ,

the relative humidity,
Tatm
object distance (Dobj)
the (effective) temperature of the object surroundings, or the reflected ambient
temperature Trefl, and
the temperature of the atmosphere Tatm
This task could sometimes be a heavy burden for the operator since there are
normally no easy ways to find accurate values of emittance and atmospheric
transmittance for the actual case. The two temperatures are normally less of a
problem provided the surroundings do not contain large and intense radiation
sources.
A natural question in this connection is: How important is it to know the right
values of these parameters? It could though be of interest to get a feeling for this
problem already here by looking into some different measurement cases and
compare the relative magnitudes of the three radiation terms. This will give indications about when it is important to use correct values of which parameters.
The figures below illustrates the relative magnitudes of the three radiation contributions for three different object temperatures, two emittances, and two spectral
ranges: SW and LW. Remaining parameters have the following fixed values:
128
= 0.88
Trefl = +20 C (+68 F)

Tatm = +20 C (+68 F)
It is obvious that measurement of low object temperatures are more critical than
measuring high temperatures since the disturbing radiation sources are relatively
much stronger in the first case. Should also the object emittance be low, the situation would be still more difficult.
We have finally to answer a question about the importance of being allowed to
use the calibration curve above the highest calibration point, what we call extrapolation. Imagine that we in a certain case measure Utot = 4.5 volts. The highest
calibration point for the camera was in the order of 4.1 volts, a value unknown to
the operator. Thus, even if the object happened to be a blackbody, i.e. Uobj = Utot,
we are actually performing extrapolation of the calibration curve when converting
4.5 volts into temperature.
Let us now assume that the object is not black, it has an emittance of 0.75, and
the transmittance is 0.92. We also assume that the two second terms of Equation
4 amount to 0.5 volts together. Computation of Uobj by means of Equation 4 then
results in Uobj = 4.5 / 0.75 / 0.92 0.5 = 6.0. This is a rather extreme extrapolation,
particularly when considering that the video amplifier might limit the output to
5 volts! Note, though, that the application of the calibration curve is a theoretical
procedure where no electronic or other limitations exist. We trust that if there had
been no signal limitations in the camera, and if it had been calibrated far beyond
5 volts, the resulting curve would have been very much the same as our real curve
extrapolated beyond 4.1 volts, provided the calibration algorithm is based on radiation physics, like the FLIR Systems algorithm. Of course there must be a limit
to such extrapolations.
129
10400603;2
Figure 18.3 Relative magnitudes of radiation sources under varying measurement conditions (SW
camera). 1: Object temperature; 2: Emittance; Obj: Object radiation; Refl: Reflected radiation; Atm:
atmosphere radiation. Fixed parameters: = 0.88; Trefl = 20 C (+68 F); Tatm = 20 C (+68 F).
130
10400703;2
Figure 18.4 Relative magnitudes of radiation sources under varying measurement conditions (LW
camera). 1: Object temperature; 2: Emittance; Obj: Object radiation; Refl: Reflected radiation; Atm:
atmosphere radiation. Fixed parameters: = 0.88; Trefl = 20 C (+68 F); Tatm = 20 C (+68 F).
131
19
Emissivity tables
This section presents a compilation of emissivity data from the infrared literature
and FLIR Systemss own measurements.
19.1
References
Mikal A. Bramson: Infrared Radiation, A Handbook for Applications, Plenum press,

N.Y.
William L. Wolfe, George J. Zissis: The Infrared Handbook, Office of Naval Research,
Department of Navy, Washington, D.C.
Madding, R. P.: Thermographic Instruments and systems. Madison, Wisconsin: University of Wisconsin Extension, Department of Engineering and Applied Science.
William L. Wolfe: Handbook of Military Infrared Technology, Office of Naval Research,

Department of Navy, Washington, D.C.
Jones, Smith, Probert: External thermography of buildings..., Proc. of the Society of

Photo-Optical Instrumentation Engineers, vol.110, Industrial and Civil Applications
of Infrared Technology, June 1977 London.
Paljak, Pettersson: Thermography of Buildings, Swedish Building Research Institute,

Stockholm 1972.
Vlcek, J: Determination of emissivity with imaging radiometers and some emissivities

at = 5 m. Photogrammetric Engineering and Remote Sensing.
Kern: Evaluation of infrared emission of clouds and ground as measured by weather

satellites, Defence Documentation Center, AD 617 417.
hman, Claes: Emittansmtningar med AGEMA E-Box. Teknisk rapport, AGEMA

1999. (Emittance measurements using AGEMA E-Box. Technical report, AGEMA
1999.)
19.2
Tables
Figure 19.1 T: Total spectrum; SW: 25 m; LW: 814 m, LLW: 6.520 m; 1: Material; 2: Specification;
3: Temperature in C; 4: Spectrum; 5: Emissivity: 6: Reference
132
Aluminum
anodized, black,
dull
70
LW
0.95
Aluminum
anodized, black,
dull
70
SW
0.67
19.2 Tables
1
Aluminum
anodized, light
gray, dull
70
LW
0.97
Aluminum
anodized, light
gray, dull
70
SW
0.61
Aluminum
anodized sheet
100
0.55
Aluminum
as received, plate
100
0.09
Aluminum
as received, sheet
100
0.09
Aluminum
cast, blast
cleaned
70
LW
0.46
Aluminum
cast, blast
cleaned
70
SW
0.47
Aluminum
dipped in HNO3,
plate
100
0.05
Aluminum
foil
27
3 m
0.09
Aluminum
foil
27
10 m
0.04
Aluminum
oxidized, strongly
50500
0.20.3
Aluminum
polished
50100
0.040.06
Aluminum
polished, sheet
100
0.05
Aluminum
polished plate
100
0.05
Aluminum
roughened
27
3 m
0.28
Aluminum
roughened
27
10 m
0.18
Aluminum
rough surface
2050
0.060.07
Aluminum
sheet, 4 samples
differently
scratched
70
LW
0.030.06
Aluminum
sheet, 4 samples
differently
scratched
70
SW
0.050.08
Aluminum
vacuum deposited
20
0.04
133
19.2 Tables
1
Aluminum
weathered, heavily
17
SW
0.830.94
20
0.60
Aluminum
bronze
Aluminum hydroxide
powder
0.28
Aluminum oxide
activated, powder
0.46
Aluminum oxide
pure, powder
(alumina)
0.16
Asbestos
board
0.96
Asbestos
fabric
0.78
Asbestos
floor tile
35
SW
0.94
Asbestos
paper
40400
0.930.95
Asbestos
powder
0.400.60
Asbestos
slate
20
0.96
LLW
0.967
Asphalt paving
134
20
Brass
dull, tarnished
20350
0.22
Brass
oxidized
70
SW
0.040.09
Brass
oxidized
70
LW
0.030.07
Brass
oxidized
100
0.61
Brass
oxidized at
600C
200600
0.590.61
Brass
polished
200
0.03
Brass
polished, highly
100
0.03
Brass
rubbed with 80grit emery
20
0.20
Brass
sheet, rolled
20
0.06
Brass
sheet, worked
with emery
20
0.2
19.2 Tables
1
Brick
alumina
17
SW
0.68
Brick
common
17
SW
0.860.81
Brick
Dinas silica,
glazed, rough
1100
0.85
Brick
Dinas silica, refractory
1000
0.66
Brick
Dinas silica,
unglazed, rough
1000
0.80
Brick
firebrick
17
SW
0.68
Brick
fireclay
20
0.85
Brick
fireclay
1000
0.75
Brick
fireclay
1200
0.59
Brick
masonry
35
SW
0.94
Brick
masonry, plastered
20
0.94
Brick
red, common
20
0.93
Brick
red, rough
20
0.880.93
Brick
refractory, corundum
1000
0.46
Brick
refractory, magnesite
10001300
0.38
Brick
refractory,
strongly radiating
5001000
0.80.9
Brick
refractory, weakly
radiating
5001000
0.650.75
Brick
silica, 95% SiO2
1230
0.66
Brick
sillimanite, 33%
SiO2, 64% Al2O3
1500
0.29
Brick
waterproof
17
SW
0.87
Bronze
phosphor bronze
70
LW
0.06
135
19.2 Tables
1
Bronze
phosphor bronze
70
SW
0.08
Bronze
polished
50
0.1
Bronze
porous, rough
50150
0.55
Bronze
powder
0.760.80
Carbon
candle soot
0.95
Carbon
charcoal powder
0.96
Carbon
graphite, filed
surface
0.98
Carbon
graphite powder
0.97
Carbon
lampblack
20400
0.950.97
Chipboard
untreated
20
SW
0.90
Chromium
polished
50
0.10
Chromium
polished
5001000
0.280.38
Clay
fired
70
0.91
Cloth
black
20
0.98
20
0.92
Concrete
136
20
20
Concrete
dry
36
SW
0.95
Concrete
rough
17
SW
0.97
Concrete
walkway
LLW
0.974
Copper
commercial, burnished
20
0.07
Copper
electrolytic, carefully polished
80
0.018
Copper
electrolytic, polished
34
0.006
Copper
molten
11001300
0.130.15
Copper
oxidized
50
0.60.7
Copper
oxidized, black
27
0.78
19.2 Tables
1
Copper
oxidized, heavily
20
0.78
Copper
oxidized to blackness
0.88
Copper
polished
50100
0.02
Copper
polished
100
0.03
Copper
polished, commercial
27
0.03
Copper
polished, mechanical
22
0.015
Copper
pure, carefully
prepared surface
22
0.008
Copper
scraped
27
0.07
Copper dioxide
powder
0.84
Copper oxide
red, powder
0.70
0.89
80
0.85
20
0.9
Ebonite
Emery
coarse
Enamel
Enamel
lacquer
20
0.850.95
Fiber board
hard, untreated
20
SW
0.85
Fiber board
masonite
70
LW
0.88
Fiber board
masonite
70
SW
0.75
Fiber board
particle board
70
LW
0.89
Fiber board
particle board
70
SW
0.77
Fiber board
porous, untreated
20
SW
0.85
Gold
polished
130
0.018
Gold
polished, carefully
200600
0.020.03
Gold
polished, highly
100
0.02
137
19.2 Tables
1
Granite
polished
20
LLW
0.849
Granite
rough
21
LLW
0.879
Granite
rough, 4 different
samples
70
LW
0.770.87
Granite
rough, 4 different
samples
70
SW
0.950.97
20
0.80.9
Gypsum
Ice: See Water
138
Iron, cast
casting
50
0.81
Iron, cast
ingots
1000
0.95
Iron, cast
liquid
1300
0.28
Iron, cast
machined
8001000
0.600.70
Iron, cast
oxidized
38
0.63
Iron, cast
oxidized
100
0.64
Iron, cast
oxidized
260
0.66
Iron, cast
oxidized
538
0.76
Iron, cast
oxidized at
600C
200600
0.640.78
Iron, cast
polished
38
0.21
Iron, cast
polished
40
0.21
Iron, cast
polished
200
0.21
Iron, cast
unworked
9001100
0.870.95
Iron and steel
cold rolled
70
LW
0.09
Iron and steel
cold rolled
70
SW
0.20
Iron and steel
covered with red

rust
20
0.610.85
Iron and steel
electrolytic
22
0.05
Iron and steel
electrolytic
100
0.05
19.2 Tables
1
Iron and steel
electrolytic
260
0.07
Iron and steel
electrolytic, carefully polished
175225
0.050.06
Iron and steel
freshly worked
with emery
20
0.24
Iron and steel
ground sheet
9501100
0.550.61
Iron and steel
heavily rusted
sheet
20
0.69
Iron and steel
hot rolled
20
0.77
Iron and steel
hot rolled
130
0.60
Iron and steel
oxidized
100
0.74
Iron and steel
oxidized
100
0.74
Iron and steel
oxidized
125525
0.780.82
Iron and steel
oxidized
200
0.79
Iron and steel
oxidized
1227
0.89
Iron and steel
oxidized
200600
0.80
Iron and steel
oxidized strongly
50
0.88
Iron and steel
oxidized strongly
500
0.98
Iron and steel
polished
100
0.07
Iron and steel
polished
4001000
0.140.38
Iron and steel
polished sheet
7501050
0.520.56
Iron and steel
rolled, freshly
20
0.24
Iron and steel
rolled sheet
50
0.56
Iron and steel
rough, plane surface
50
0.950.98
Iron and steel
rusted, heavily
17
SW
0.96
Iron and steel
rusted red, sheet
22
0.69
Iron and steel
rusty, red
20
0.69
139
19.2 Tables
140
Iron and steel
shiny, etched
150
0.16
Iron and steel
shiny oxide layer,

sheet,
20
0.82
Iron and steel
wrought, carefully polished
40250
0.28
Iron galvanized
heavily oxidized
70
LW
0.85
Iron galvanized
heavily oxidized
70
SW
0.64
Iron galvanized
sheet
92
0.07
Iron galvanized
sheet, burnished
30
0.23
Iron galvanized
sheet, oxidized
20
0.28
Iron tinned
sheet
24
0.064
Lacquer
3 colors sprayed
on Aluminum
70
LW
0.920.94
Lacquer
3 colors sprayed
on Aluminum
70
SW
0.500.53
Lacquer
Aluminum on
rough surface
20
0.4
Lacquer
bakelite
80
0.83
Lacquer
black, dull
40100
0.960.98
Lacquer
black, matte
100
0.97
Lacquer
black, shiny,
sprayed on iron
20
0.87
Lacquer
heatresistant
100
0.92
Lacquer
white
40100
0.80.95
Lacquer
white
100
0.92
Lead
oxidized, gray
20
0.28
Lead
oxidized, gray
22
0.28
Lead
oxidized at
200C
200
0.63
Lead
shiny
250
0.08
19.2 Tables
1
Lead
unoxidized, polished
100
0.05
Lead red
100
0.93
Lead red, powder
100
0.93
0.750.80
0.30.4
Leather
tanned
Lime
Magnesium
22
0.07
Magnesium
260
0.13
Magnesium
538
0.18
20
0.07
0.86
Magnesium
polished
Magnesium
powder
Molybdenum
6001000
0.080.13
Molybdenum
15002200
0.190.26
7002500
0.10.3
17
SW
0.87
Molybdenum
filament
Mortar
Mortar
dry
36
SW
0.94
Nichrome
rolled
700
0.25
Nichrome
sandblasted
700
0.70
Nichrome
wire, clean
50
0.65
Nichrome
wire, clean
5001000
0.710.79
Nichrome
wire, oxidized
50500
0.950.98
Nickel
bright matte
122
0.041
Nickel
commercially
pure, polished
100
0.045
Nickel
commercially
pure, polished
200400
0.070.09
Nickel
electrolytic
22
0.04
141
19.2 Tables
142
Nickel
electrolytic
38
0.06
Nickel
electrolytic
260
0.07
Nickel
electrolytic
538
0.10
Nickel
electroplated,
polished
20
0.05
Nickel
electroplated on
iron, polished
22
0.045
Nickel
electroplated on
iron, unpolished
20
0.110.40
Nickel
electroplated on
iron, unpolished
22
0.11
Nickel
oxidized
200
0.37
Nickel
oxidized
227
0.37
Nickel
oxidized
1227
0.85
Nickel
oxidized at
600C
200600
0.370.48
Nickel
polished
122
0.045
Nickel
wire
2001000
0.10.2
Nickel oxide
500650
0.520.59
Nickel oxide
10001250
0.750.86
Oil, lubricating
0.025 mm film
20
0.27
Oil, lubricating
0.050 mm film
20
0.46
Oil, lubricating
0.125 mm film
20
0.72
Oil, lubricating
film on Ni base:
Ni base only
20
0.05
Oil, lubricating
thick coating
20
0.82
Paint
8 different colors
and qualities
70
LW
0.920.94
Paint
8 different colors
and qualities
70
SW
0.880.96
19.2 Tables
1
Paint
Aluminum, various ages
50100
0.270.67
Paint
cadmium yellow
0.280.33
Paint
chrome green
0.650.70
Paint
cobalt blue
0.70.8
Paint
oil
17
SW
0.87
Paint
oil, black flat
20
SW
0.94
Paint
oil, black gloss
20
SW
0.92
Paint
oil, gray flat
20
SW
0.97
Paint
oil, gray gloss
20
SW
0.96
Paint
oil, various colors
100
0.920.96
Paint
oil based, average of 16 colors
100
0.94
Paint
plastic, black
20
SW
0.95
Paint
plastic, white
20
SW
0.84
Paper
4 different colors
70
LW
0.920.94
Paper
4 different colors
70
SW
0.680.74
Paper
black
0.90
Paper
black, dull
0.94
Paper
black, dull
70
LW
0.89
Paper
black, dull
70
SW
0.86
Paper
blue, dark
0.84
Paper
coated with black

lacquer
0.93
Paper
green
0.85
Paper
red
0.76
Paper
white
0.70.9
20
143
19.2 Tables
1
Paper
white, 3 different
glosses
70
LW
0.880.90
Paper
white, 3 different
glosses
70
SW
0.760.78
Paper
white bond
20
0.93
Paper
yellow
0.72
17
SW
0.86
Plaster
144
Plaster
plasterboard, untreated
20
SW
0.90
Plaster
rough coat
20
0.91
Plastic
glass fibre laminate (printed circ.

board)
70
LW
0.91
Plastic
glass fibre laminate (printed circ.

board)
70
SW
0.94
Plastic
polyurethane isolation board
70
LW
0.55
Plastic
polyurethane isolation board
70
SW
0.29
Plastic
PVC, plastic floor,

dull, structured
70
LW
0.93
Plastic
PVC, plastic floor,

dull, structured
70
SW
0.94
Platinum
17
0.016
Platinum
22
0.03
Platinum
100
0.05
Platinum
260
0.06
Platinum
538
0.10
Platinum
10001500
0.140.18
Platinum
1094
0.18
19.2 Tables
1
Platinum
pure, polished
200600
0.050.10
Platinum
ribbon
9001100
0.120.17
Platinum
wire
50200
0.060.07
Platinum
wire
5001000
0.100.16
Platinum
wire
1400
0.18
Porcelain
glazed
20
0.92
Porcelain
white, shiny
0.700.75
Rubber
hard
20
0.95
Rubber
soft, gray, rough
20
0.95
0.60
20
0.90
Sand
Sand
Sandstone
polished
19
LLW
0.909
Sandstone
rough
19
LLW
0.935
Silver
polished
100
0.03
Silver
pure, polished
200600
0.020.03
Skin
human
32
0.98
Slag
boiler
0100
0.970.93
Slag
boiler
200500
0.890.78
Slag
boiler
6001200
0.760.70
Slag
boiler
14001800
0.690.67
Soil
dry
20
0.92
Soil
saturated with
water
20
0.95
Stainless steel
alloy, 8% Ni,
18% Cr
500
0.35
Stainless steel
rolled
700
0.45
Snow: See Water
145
19.2 Tables
1
Stainless steel
sandblasted
700
0.70
Stainless steel
sheet, polished
70
LW
0.14
Stainless steel
sheet, polished
70
SW
0.18
Stainless steel
sheet, untreated,
somewhat
scratched
70
LW
0.28
Stainless steel
sheet, untreated,
somewhat
scratched
70
SW
0.30
Stainless steel
type 18-8, buffed
20
0.16
Stainless steel
type 18-8, oxidized at 800C
60
0.85
Stucco
rough, lime
1090
0.91
Styrofoam
insulation
37
SW
0.60
0.790.84
Tar
146
Tar
paper
20
0.910.93
Tile
glazed
17
SW
0.94
Tin
burnished
2050
0.040.06
Tin
tinplated sheet
iron
100
0.07
Titanium
oxidized at
540C
200
0.40
Titanium
oxidized at
540C
500
0.50
Titanium
oxidized at
540C
1000
0.60
Titanium
polished
200
0.15
Titanium
polished
500
0.20
Titanium
polished
1000
0.36
Tungsten
200
0.05
Tungsten
6001000
0.10.16
19.2 Tables
1
Tungsten
15002200
0.240.31
Tungsten
filament
3300
0.39
Varnish
flat
20
SW
0.93
Varnish
on oak parquet
floor
70
LW
0.900.93
Varnish
on oak parquet
floor
70
SW
0.90
Wallpaper
slight pattern,
light gray
20
SW
0.85
Wallpaper
slight pattern,
red
20
SW
0.90
Water
distilled
20
0.96
Water
frost crystals
10
0.98
Water
ice, covered with

heavy frost
0.98
Water
ice, smooth
10
0.96
Water
ice, smooth
0.97
Water
layer >0.1 mm
thick
0100
0.950.98
Water
snow
0.8
Water
snow
10
0.85
Wood
17
SW
0.98
Wood
19
LLW
0.962
0.50.7
Wood
ground
Wood
pine, 4 different
samples
70
LW
0.810.89
Wood
pine, 4 different
samples
70
SW
0.670.75
Wood
planed
20
0.80.9
Wood
planed oak
20
0.90
147
19.2 Tables
148
Wood
planed oak
70
LW
0.88
Wood
planed oak
70
SW
0.77
Wood
plywood,
smooth, dry
36
SW
0.82
Wood
plywood, untreated
20
SW
0.83
Wood
white, damp
20
0.70.8
Zinc
oxidized at
400C
400
0.11
Zinc
oxidized surface
10001200
0.500.60
Zinc
polished
200300
0.040.05
Zinc
sheet
50
0.20
Index
Index
*.tcf
uploading,35
+/ button
function,34
location,27
1
1 194 109,7
1 195 267,7
1 195 268,7
1 195 314,7
1 195 317,7
1 195 346,7
1 909 503,7
1 909 528,7
1 909 653,7
1 909 775,7
1 909 812,7
1 909 813,7
1 909 820,7
117 132,7
4
4" LCD,28
4" LCD / remote control
in packing list,7
A
about FLIR Systems,2
A button
function,33
location,29
remote control,33
accessories
cleaning,86
accuracy,90
acquiring
image,14
adapter CompactFlash card
in packing list,7
Add box
command,52
Add circle
command,55
Add diff
command,63
Add isotherm
command,61
Add line
command,58
address,ii
Add spot
command,50
Add visual marker
command,67
adjusting
focus,23
visual alarm,19
Alarm setup
dialog box,73
Alarm temp
label,73
Analysis
menu,50
atmospheric transmission correction,90
attaching
remote control,26
audio
input,91
output,91
autofocus
explanation,34
how to,23
B
bands
extreme infrared,116
far infrared,116
middle infrared,116
near infrared,116
battery,80
in packing list,7
inserting,24
operating time,90
removing,24
type,90
battery charger
external,80
in packing list,7
internal,80
battery charging
external,81
internal,80
battery indicator,36
battery status bar,36
battery system,80
149
Index C
blackbody
construction,117
explanation,117
practical application,117
box
laying out & moving,15
resizing,17
Box
shortcut menu,53
Box settings
dialog box,54
Burst recording
command,43
dialog box,43
burst recording indicator,36
buttons
function
+/ button,34
A button,33
C button,33
F1 button,34
F2 button,34
Laser LocatIR button,34
ON/OFF button,33
S button,33
location
+/ button,27
A button,29
C button,29
F1 button,28
F2 button,28
Laser LocatIR,32
ON/OFF button,30
S button,29
remote control
A button,33
C button,33
S button,33
Buttons
command,77
dialog box,77
C
cables
cleaning,86
calibration,1
time between,1
camera body
cleaning,86
Camera info
command,79
dialog box,79
camera overview,27
150
camera parts
+/ button,27
4" LCD,28
camera status LCD,28
connectors
headset,29
remote control,28
RS-232/USB,29
F1 button,28
F2 button,28
function
joystick,34
hand strap,29
IrDA
location,31
joystick
on camera body,30
on remote control,33
Laser LocatIR,32
location,32
lid battery compartment,29
remote control,28
video lamp,29
viewfinder,28
visual camera,37
camera status LCD,28
symbols
battery indicator,36
battery status bar,36
burst recording indicator,36
communication indicator,36
CompactFlash card indicator,36
CompactFlash card status bar,36
external power indicator,36
power indicator,36
canceling
selections,40
cavity radiator
applications,117
explanation,117
C button
function,33
location,29
remote control,33
changing
date & time,22
date format,21
focus,23
focus manually,23
isotherm,17
language,21
lens,23
level,20
Index D
size of measurement marker,17
span,20
system settings
date & time,22
date format,21
language,21
temperature unit,21
time format,22
temperature unit,21
time format,22
visual alarm,19
charging, battery
externally,81
internally,80
circle
Circle
shortcut menu,55
Circle settings
dialog box,56
cleaning
accessories,86
cables,86
camera body,86
lenses,86
commands
Add box,52
Add circle,55
Add diff,63
Add isotherm,61
Add line,58
Add spot,50
Add visual marker,67
Burst recording,43
Buttons,77
Camera info,79
Continuous adjust,66
Date/Time ,77
Deactivate local par.,65
Difference,70
Digital video,74
Edit mode,50
Factory default,79
Freeze/Live,65
Hide graphics,67
Image,67
Level/Span,65
Local settings,78
Manual adjust,66
Obj par,64
Palette,66
Periodic save,43
Power,75
Profile,79
Range,65
Ref temp,64
Remove all,64
Save,42, 71
Show graphics,67
Status bar,76
Text comment,46
Type,73
Visual/IR,65
Voice comment,45
communication indicator,36
CompactFlash card
indicator,36
in packing list,7
status bar,36
confirming
selections,40
connecting
LEMO connectors,84
connectors
headset,29
remote control,28
RS-232/USB,29
contact details,ii
Continuous adjust
command,66
copyright,ii
creating
isotherm,17
D
Date/Time
command,77
dialog box,77
date & time
changing,22
date format
changing,21
Deactivate local par.
command,65
Delta alarm
label,73
detector,89
Dewar, James,115
dialog boxes
Alarm setup,73
Box settings,54
Burst recording,43
Buttons,77
Camera info,79
Circle settings,56
Date/Time,77
151
Index E
Difference settings,70
Digital video,74
Image setup,67
Isotherm settings,63
Line settings,59
Local settings,78
Obj par,64
Palette,66
Periodic save,43
Power setup,75
Range,65
Ref temp,64
Save setup,71
Spot settings,51
Status bar,76
Text comment,46
Voice comment,45
Difference
command,70
Difference settings
dialog box,70
digital image enhancement,89
digital video
specifications,89
Digital video
command,74
dialog box,74
dimensional drawings,89
displaying
menu system,40
E
Edit mode
command,50
electrical power system,80
power management,91
specifications,90
voltage,90
electromagnetic spectrum,116
electronic zoom,89
e-mail,ii
emissivity
data,132
explanation,110
finding using reference,111
finding using thermocouple,111
tables,132
emissivity correction,90
encapsulation,91
environmental specifications
encapsulation,91
humidity,91
operating temperature range,91
152
shock,91
storage temperature range,91
vibration,91
error messages,40
exiting
menu system,40
external battery charger,80
external optics correction,90
external power indicator,36
extreme infrared band,116
F
F1 button
function,34
location,28
F2 button
function,34
location,28
Factory default
command,79
far infrared band,116
field of view,89
file
opening,14
saving,15
file naming
current date,72
current directory,72
unique counter,71
FireWire,91
FireWire cable 4/4
in packing list,7
FireWire cable 4/6
in packing list,7
FLIR Systems
about,2
contact details,ii
copyright,ii
e-mail,ii
history,2
E series,3
first thermo-electrically cooled,3
model 525,3
model 650,3
model 750,3
model 780,3
model P60,3
thermo-electrically cooled, first,3
ISO 9001,ii
legal disclaimer,ii
patents,ii
patents pending,ii
postal address,ii
Index G
product warranty,ii
quality assurance,ii
quality management system,ii
requests for enhancement,5
RFE,5
telefax number,ii
telephone number,ii
trademarks,ii
warranty,ii
website,ii
focus
how to,23
formulas
Planck's law,118
Stefan Boltzmann's formula,121
Wien's displacement law,119
FOV,89
Freeze/Live
command,65
freezing
image,15
Function
label,73
G
glossary,109
graybody,123
Gustav Robert Kirchhoff,117
H
hand strap,29
headset
in packing list,7
headset connector,29
heat picture,114
Herschel, William,112
Hide graphics
command,67
history,2
E series,3
first thermo-electrically cooled,3
infrared technology,112
model 525,3
model 650,3
model 750,3
model 780,3
model P60,3
thermo-electrically cooled, first,3
humidity,91
I
Identity
labels,73
image
acquiring,14
freezing,15
opening,14
saving,15
unfreezing,15
Image
command,67
menu,65
image frequency,89
image naming
current date,72
unique counter,71
Image setup
dialog box,67
imaging performance,89
indicators
battery,36
battery status,36
burst recording,36
communication,36
CompactFlash card,36
CompactFlash card status bar,36
external power,36
on battery charger,82
power,36
infrared communications link,31
how it works,35
infrared semi-transparent body,124
infrared technology
history,112
inserting
battery,24
interfaces,91
RS-232,91
USB,91
internal battery charger,80
IrDA
how it works,35
location,31
ISO 9001,ii
isotherm
creating & changing,17
Isotherm
shortcut menu,62
Isotherm settings
dialog box,63
153
Index J
J
James Dewar,115
Josef Stefan,121
joystick
function,34
on camera body,30
on remote control,33
K
keys
function
+/ button,34
A button,33
C button,33
F1 button,34
F2 button,34
Laser LocatIR button,34
ON/OFF button,33
S button,33
location
+/ button,27
A button,29
C button,29
F1 button,28
F2 button,28
Laser LocatIR,32
ON/OFF button,30
S button,29
remote control
A button,33
C button,33
S button,33
Kirchhoff, Gustav Robert,117
L
labels
Alarm temp,73
Delta alarm,73
Function,73
Identity,73
Output,73
Ref temp,73
Set from ref temp,73
Type,73
Landriani, Marsilio,112
Langley, Samuel P.,114
language
changing,21
Laser LocatIR
button,32
classification,90
description,37
154
distance,37
function,34
location on camera,32
output power,37
type,90
warning,37
wavelength,37
laws
Planck's law,118
Stefan-Boltzmann's formula,121
Wien's displacement law,119
laying out & moving
box,15
circle,16
line,16
spot,15
LCD protection,1, 75
LED indicators
on battery charger,82
legal disclaimer,ii
LEMO connectors,84
lens
cleaning,86
mounting,23
lens cap
in packing list,7
Leopoldo Nobili,114
level
changing,20
Level/Span
command,65
lid battery compartment,29
line
Line
shortcut menu,58
Line settings
dialog box,59
Local settings
command,78
dialog box,78
Ludwig Boltzmann,121
M
Macedonio Melloni,113
Manual adjust
command,66
Marsilio Landriani,112
Material Safety Data Sheets,86
Max Planck,118
measurement formula,126
measurement marker
resizing,17
Index N
measurements
working with,15
measurement situation
general thermographic,126
Melloni, Macedonio,113
menus
Analysis,50
Image,65
Setup,67
shortcut menus
Box,53
Circle,55
Isotherm,62
Line,58
Spot,50
menu system,40
canceling
selections,40
confirming
selections,40
displaying,40
exiting,40
navigating,40
messages,40
middle infrared band,116
minimum focus distance,89
mounting
lens,23
moving
box,15
circle,16
line,16
spot,15
MSDS,86
N
naming
naming images
current date,72
unique counter,71
navigating menu system,40
near infrared band,116
Nobili, Leopoldo ,114
non-blackbody emitters,122
O
Obj par
command,64
dialog box,64
ON/OFF button
function,33
location,30
opening
file,14
image,14
operating time,90
optics transmission correction,90
Output
label,73
P
packing list,7
4" LCD / remote control,7
adapter CompactFlash card,7
battery,7
battery charger,7
CompactFlash card,7
FireWire cable 4/4,7
FireWire cable 4/6,7
headset,7
lens cap,7
power supply,7
shoulder strap,7
USB cable,7
video cable,7
video lens 12,7
Palette
command,66
dialog box,66
part numbers
1 194 109,7
1 195 267,7
1 195 268,7
1 195 314,7
1 195 317,7
1 195 346,7
1 909 503,7
1 909 528,7
1 909 653,7
1 909 775,7
1 909 812,7
1 909 813,7
1 909 820,7
117 132,7
patents,ii
patents pending,ii
Periodic save
command,43
dialog box,43
physical specifications
size,91
tripod mount,91
weight,91
Planck, Max,118
155
Index Q
postal address,ii
Power
command,75
power indicator,36
power input,91
power management,91
Power setup
dialog box,75
power supply,80
in packing list,7
product warranty,ii
Profile
command,79
Q
quality assurance,ii
quality management system,ii
R
radiation power terms
emission from atmosphere,127
emission from object,127
reflected emission from ambient source,127
radiation sources
relative magnitudes,130, 131
radiators
cavity radiator,117
graybody radiators,123
selective radiators,123
Range
command,65
dialog box,65
recalling
file,14
image,14
reflected ambient temperature
explanation,111
reflected ambient temperature correction,90
Ref temp
command,64
dialog box,64
label,73
relative magnitudes
radiation sources,130, 131
remote control,28
attaching,26
removing,25
remote control connector,28
Remove all
command,64
removing
battery,24
remote control,25
156
requests for enhancement,5

resizing measurement marker,17
result table
screen object,38
signs in,38
RFE,5
RS-232,91
RS-232/USB connector,29
S
Samuel P. Langley,114
Save
command,42, 71
Save setup
dialog box,71
saving
file,15
image,15
S button
function,33
location,29
remote control,33
scale
screen object,39
screen objects
result table,38
status bar,39
temperature scale,39
selections
canceling,40
confirming,40
semi-transparent body,124
Set from ref temp
labels,73
Setup
menu,67
shock,91
shortcut menus
Box,53
Circle,55
Isotherm,62
Line,58
Spot,50
shoulder strap
in packing list,7
Show graphics
command,67
Sir James Dewar,115
Sir William Herschel,112
size,91
span
changing,20
spatial resolution,89
Index T
specifications
environmental
encapsulation,91
humidity,91
shock,91
vibration,91
physical
size,91
tripod mount,91
weight,91
technical,89
spectral range,89
spectrum
thermometrical,113
spot
Spot
shortcut menu,50
Spot settings
dialog box,51
status area,39
status bar
screen object,39
Status bar
command,76
dialog box,76
Stefan, Josef,121
switching off camera,14
switching on camera,14
system messages
status messages,40
warning messages,40
system settings
changing
date & time,22
date format,21
language,21
temperature unit,21
time format,22
T
technical specifications,89
technical support,6
telefax number,ii
telephone number,ii
temperature range
operating,91
storage,91
temperature ranges,90
temperature scale
screen object,39
temperature unit
changing,21
Text comment
command,46
dialog box,46
text comment files
uploading,35
theory of thermography,116
thermograph,114
thermographic measurement techniques
introduction,110
thermographic theory,116
thermometrical spectrum,113
thermos bottle,115
time & date
changing,22
time format
changing,22
trademarks,ii
transferring text comment files,35
tripod mount,91
turning off camera,14
turning on camera,14
tutorials
acquiring
image,14
adjusting
focus,23
attaching
remote control,26
changing
date & time,22
date format,21
focus,23
isotherm,17
language,21
level,20
span,20
temperature unit,21
time format,22
visual alarm,19
creating
isotherm,17
freezing
image,15
inserting
battery,24
laying out & moving
box,15
circle,16
line,16
157
Index U
spot,15
measuring temperature,15, 16
mounting
lens,23
opening
image,14
recalling
image,14
removing
battery,24
remote control,25
resizing measurement marker,17
saving
image,15
switching off camera,14
switching on camera,14
unfreezing
image,15
zooming,23
Type
command,73
label,73
U
unfreezing
image,15
unpacking,7
uploading text comment files,35
USB,91
USB cable
in packing list,7
W
warning messages,40
warnings
battery,82
intensive energy sources,1
interference,1
radio frequency energy,1
warranty,ii
website,ii
weight,91
Wien, Wilhelm,119
Wilhelm Wien,119
William Herschel,112
working with
level,20
span,20
working with camera
adjusting
focus,23
attaching
remote control,26
inserting
battery,24
mounting
lens,23
removing
battery,24
remote control,25
zooming,23
working with measurements,15
Z
V
vibration,91
video cable
in packing list,7
video camera,37
video lamp,29
video lens 12
in packing list,7
viewfinder,28
specifications,89
Visual/IR
command,65
visual alarm
changing,19
visual camera,37
Voice comment
command,45
dialog box,45
158
zoom
how to,23
This manual was produced using XML Extensible Markup Language. For more information about XML, point your browser to:
http://www.w3c.org/XML/
Description
Software
Supplier
URL
Version control
ExcoConf
Excosoft
http://www.excosoft.se/eweb/site/exc_pd.html
Editing environment
XML Client
Excosoft
http://www.excosoft.se/eweb/site/excoconf_pd.html
Preformatting
ExcoForm
Excosoft
http://www.excosoft.se/eweb/site/home.html
XML parser
Xerces
Apache
http://xml.apache.org/xerces-j
XSLT processor
Xalan
Apache
http://xml.apache.org/xalan-j
XSL-FO rendering engine
XEP
RenderX
http://www.renderx.com
The following file identities and versions were used in this manual:
(manbase)20234903.xml;10
(p)20235503.xml;16
(p)20235603.xml;16
(p)20235703.xml;16
(p)20235803.xml;17
(p)20235903.xml;20
(p)20236003.xml;9
(p)20236103.xml;11
(p)20236203.xml;17
(p)20236503.xml;9
(p)20236803.xml;9
(p)20237103.xml;5
(p)20237503.xml;8
(p)20237703.xml;11
(p)R0047.rcp;2
159
160
FLIR Systems AB
World Wide Thermography Center
P.O. Box 3
SE-182 11 Danderyd
Sweden
Tel.: +46 (0)8 753 25 00
Fax: +46 (0)8 753 23 64
E-mail: sales@flir.se
Web: www.flir.com
FLIR Systems Ltd.

2 Kings Hill Avenue Kings Hill
West Malling
Kent, ME19 4AQ
United Kingdom
Tel.: +44 (0)1732 220 011
Fax: +44 (0)1732 843 707
E-mail: sales@flir.uk.com
Web: www.flir.com
FLIR Systems Inc.

Corporate headquarters
16505 SW 72nd Avenue
Portland, OR. 97224
USA
Tel.: +1 503 684 3731
Fax: +1 503 684 5452
Web: www.flir.com
FLIR Systems S. r. l.
FLIR Systems S.r.l.
Via L. Manara, 2
20051 Limbiate (MI)
Italy
Tel. +39 02 99 45 10 01
Fax +39 02 99 69 24 08
E-mail: info@flir.it
Web: www.flir.it
FLIR Systems Sarl

18 rue Hoche BP 81
F-92134 Issy les Moulineaux
Cedex
France
Tel.: +33 (0)1 41 33 97 97
Fax: +33 (0)1 47 36 18 32
E-mail: info@flir.fr
Web: www.flir.fr
FLIR Systems GmbH
Berner Strasse 81
D-60437 Frankfurt am Main
Germany
Tel.: +49 (0)69 95 00 900
Fax: +49 (0)69 95 00 9040
E-mail: info@flir.de
Web: www.flir.de
FLIR Systems Ltd.
5230 South Service Road, Suite #125
Burlington, ON. L7L 5K2
Canada
Tel: 1-800-613-0507 X30
Fax: 905-639-5488
E-mail: IRCanada@flir.com
FLIR Systems Co. Ltd.

Room 161315, Tower 2
Grand Central Plaza
138 Shatin Rural Committee Rd
Shatin, N.T.
Hong Kong
Tel.: +852 27 92 89 55
Fax: +852 27 92 89 52
E-mail: flir@flir.com.hk
Web: www.flir.com.hk
FLIR Systems AB
Uitbreidingstraat 6062
B-2600 Berchem
Belgium
Tel.: +32 (0)3 287 87 11
Fax: +32 (0)3 287 87 29
E-mail: info@flir.be
Web: www.flir.be
FLIR Systems Inc.
USA Thermography Center
16 Esquire Road
North Billerica, MA. 01862
USA
Tel.: +1 978 901 8000
Fax: +1 978 901 8887
E-mail: marketing@flir.com
Web: www.flir.com

FLIR P60 Manual PDF

Uploaded by

Copyright:

Available Formats

FLIR P60 Manual PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

FLIR P60 Manual PDF

Uploaded by

Copyright:

Available Formats

What does the document discuss regarding warranties?

What does the document discuss regarding warranties?

What information is provided about quality assurance?

What information is provided about quality assurance?

ThermaCAM P60

FLIR Systems AB P. O. Box 3 SE-182 11 Danderyd Sweden

+46 (0)8 753 25 00

+46 (0)8 753 23 64

Warnings & cautions ..................................................................................................................................................

Packing list .....................................................................................................................................................................

System overview .........................................................................................................................................................

Connecting system components ......................................................................................................................... 12

Removing the remote control ........................................................................ 25

Camera overview .........................................................................................................................................................

Camera program ..........................................................................................................................................................

Electrical power system ...........................................................................................................................................

10 A note on LEMO connectors ................................................................................................................................... 84

15 Thermographic measurement techniques ..................................................................................................... 110

Burst recording toolbar and progress bar ................................................................................

Explanations of the Buttons Setting dialog box ................................................................... 77

Spectral radiant emittance of three types of radiators. 1: Spectral radiant emittance;

Warnings & cautions

About FLIR Systems

With over 30 years experience in IR systems and applications development, and

2.1 About FLIR Systems

2.1 About FLIR Systems

A few images from our facilities

2.2 Comments & questions

Figure 2.4 LEFT: Diamond turning machine; RIGHT: Lens polishing

Comments & questions

FLIR Systems is committed to a policy of continuous development, and although

2.2 Comments & questions

Adapter for CompactFlash card

4" LCD/remote control

FireWire cable 4/4

NOTE: Depending on your camera

FireWire cable 4/6

CVBS video cable

NOTE: Please note the following:

Figure 4.1 System overview

Figure 4.2 Explanations of callouts

Protective plastic window

64/150 close-up IR lens

34/80 close-up IR lens

2-bay battery charger

External power supply

Automotive (cigarette lighter) 12 VDC adapter

Adapter for CompactFlash card

FireWire cable 4/6

FireWire cable 6/6

CVBS cable (composite video cable)

Infrared communication link

Connecting system components

Figure 5.1 How to connect system components, 1: Rear connectors

Power supply cable

CVBS cable (i.e. composite video)

Remote control cable

Figure 5.3 How to connect system components, 1: Front connectors

RS-232 / USB cable.