Professional Documents
Culture Documents
Kaplan
Kaplan
EXPERIMENTAL SETUP:
1. TURBINE: A reaction with a fixed propeller Kaplan runner is mounted on the setup. It has
adjustable nozzle guide vanes.
2. DYNAMOMETER: A friction dynamometer is coupled to the turbine rotor to measure the
torque. There is a spring balance at the end of the friction belt and a carrier to hold the dead
weights at the other end. The diameter of the friction drum is d.
3. TACHOMETER: it is a mechanical device to determine the rotational speed of the turbine in
revolution per minute (rpm).
4. BOURDON INLET PRESSURE GAUGE: It is used for measuring inlet pressures in meters
of water column within the range of 0-7.5 m H2O.
5. SURGE TANK: A surge tank with a sight tube to indicate the water level in the tank which is
the outlet static head.
MEASUREMENTS:
1) Set the nozzle guide vane angles to a specified degree by means of the lever.
2) Set the inlet static head of the turbine.
3) Measure the following values:
a) The speed of the turbine in rpm (N)
b) The dead weight in kg (W)
c) The force on the spring balance in kg (F)
d) The deflection of U-tube manometer in mm (P)
e) Inlet static pressure of the turbine in m (Hi)
f) Outlet static pressure of the turbine in m (Ho)
CONSTRUCTION SPECIFICATIONS:
a) Spiral Casing: Spiral casing is of close-grained cast iron with flanged inlet, designed for
constant velocity water distribution.
b) Runner: Runner is of Gunmetal with four aerofoil blades, designed to the latest hydro
dynamic principles. The runner blade pitch can be adjusted by suitable mechanism operating
through the hollow shaft.
c) Guide Vane Mechanism: Consists of GM vanes cast integral with their spindles. By suitable
external link mechanism these can be at different relative positions, and two external dummy
guide vanes are provided to indicate the exact position of the actual guide vanes working inside
the turbine, thus showing the relative as water passages through the guide mechanism for the
different position of guide vanes.
d) Shaft: Shaft is of high carbon special steel EN-8 and hollow to accommodate the runner blad
control mechanism.
e) Ball Bearings: Ball bearings are of heavy-duty type designed for long life. One double row
deep grove rigid ball bearings to take care of radial loads and a thrust and self-weight of the rotor
assembly are provided in the bearing bracket. A self-aligning type ball bearing is used in the
bearing pedestal for trouble-free operation.
f) Draught Tube: Draught tube is of mild steel fabricated construction. It is provided at the exit
of the runner.
g) Observation window: A transparent Perspex hollow cylinder window for observation of the
flow passage through the runner is provided in between the casing and the draught tube.
h) Brake arrangement: Brake arrangement consists of a machined and polished brake drum,
pulleys, cooling water supply pipe, internal water scoop, discharge pipe, rope brake etc.
i) Support pedestal: It is of cast iron, rbust in construction and supports the entire turbine
assembly, with ports for the study of flow pattern around the runner through the observation
window.
TECHNICAL SPECIFICATIONS:
1) Kaplan Turbine:
Rated Supply head :
Discharge:
Rated Speed:
Power output:
Brake Drum Diameter:
Rope Diameter:
2) Guide vane:
No. of guide vanes operating inside:
The turbine profile: Aerofoil
Width:
Depth:
Adjustment:
3) Runner:
No. of vanes:
Material: Gunmetal
Width:
Depth:
Angle Adjustment:
Hub outer dia:
Hub inner dia:
PROCEDURE:
Make sure before starting that the pipelines are free from foreign matter. Also note whether all
the joints are watertight and leak proof. Fill up clear cold fresh water through vertical column up
to the top level, so that supply pump, delivery piping, turbine, and sump are filled with water.
The guide vanes in the turbine should be in the closed position while starting the pump. Then
slowly open the butterfly valve to regulate the discharge and net supply head on the turbine in
relation to the spear settings.
Run the turbine at around 1500 rpm for sometime to check whether all the parts are working fine.
The turbine is now gradually loaded and the readings are taken. To load the turbine standard dead
weights are provided with the unit. Load the turbine gradually and do not load it suddenly. Load
the turbine gradually and at the same time open the guide vanes to run the turbine at normal
speed.
EXPERIMENT:
Turbine shall first be tested at constant net supply head by varying the load, speed and fluid vane
setting and the runner blade position. However the net supply head on the turbines may be
reduced and the turbine tested in which case the power developed by the turbine and the best
efficiency speed is also reduced.
The output power from the turbine is calculated from the readings taken in the brake and the
speed pf the shaft. The input power supplied to the turbine is calculated from the net suppy head
on the turbine and discharge through the turbine. Efficiency of the turbine being the ration
between the output and input and can be determined from these two readings.
The discharge is measured by the venture meter and with the manometer fitted with scale. Supply
head is measured with the help of the pressure gauge.
After
starting and running the turbine at normal speed for sometime, load the turbine and take readings.
Note the following:
1. Net supply head
2. Discharge
3. Turbine shaft speed
4. Brake weight
5. Spring balance reading
For any particular setting if the guide vanes and runner blades, first run the turbine at light load
and then gradually load it, by adding dead weights on the hanger. The net supply head on the
turbine shall be maintained constant at the rated value, and by adjusting the gate valve fitted just
before the turbine.
IMPORTANT FORMULAE:
Where;
N = turbine speed in RPM
T = torque in kgm i.e. T = W x Re
The value of the constant depends on the unit in which power is measured. The value of the
constant for different units of power is given below
OBSERVATION TABLE:
CALCULATIONS:
1. Net head of turbine
Where;
Hi = Inlet total head of turbine
Ho = Outlet total head of turbine
2. Discharge
Where;
k = 0.0197;
h is in mm.
3. Power extracted from fluid
Where;
= density of water (1000 kg/m3)
g = gravitational acceleration
Q = discharge
H = net head of turbine
4. Brake power
Where;
T = torque (=g.D.(W-F))
N = speed of shaft
5. Efficiency
Where;
Psh = Brake power
Ph = Power extracted from fluid
RESULT:
PRECAUTION:
1. The turbine parts must be oiled properly.