JBJ Techniques LTD Screw Pumps

01
04
Quality Products for Mechanical
& Fluid Power
SCREW PUMPS
CONTENTS
quality products for mechanical & fluid power
The details contained within this catalogue are reproduced in accordance with the latest information at going to press E & OE
Page
Product list ...................................................................................................................................................................................... I
Introduction ..................................................................................................................................................................................... II - III
Screw Pump Range ....................................................................................................................................................................... IV - V
Quick Flow Size Chart .................................................................................................................................................................. 1
PDA Series with valve .................................................................................................................................................................. 2 - 3
PX Series ......................................................................................................................................................................................... 4 - 5
PGA4 Series .................................................................................................................................................................................... 6 - 7
PO Series ........................................................................................................................................................................................ 8 - 9
PQJ Series ...................................................................................................................................................................................... 10 - 11
PE4 Series ....................................................................................................................................................................................... 12 - 13
PE4 Series with relif valve ........................................................................................................................................................... 14 - 15
PEA3 Series .................................................................................................................................................................................... 16 - 17
PEA3 Series with relief valve ...................................................................................................................................................... 18 - 19
PC Series with axial inlet flange ................................................................................................................................................. 20 - 21
PC Series with radial inlet flange ................................................................................................................................................ 22 - 23
PH4 Series ....................................................................................................................................................................................... 24 - 25
PF6 Series balanced idlers .......................................................................................................................................................... 26 - 27
PU Series with axial inlet flange ................................................................................................................................................. 28 - 29
PU Series with radial inlet flange ................................................................................................................................................ 30 - 31
PAV Series with bellhousing ......................................................................................................................................................... 32 - 33
PA Series with strainer ................................................................................................................................................................. 34 - 35
PA Series with axial inlet flange .................................................................................................................................................. 36 - 37
VMP Pressure relief valve ........................................................................................................................................................... 38 - 39
MD Series - Direct Coupling Motor Pumps .............................................................................................................................. 40

SCREW PUMPS INTRODUCTION
Our screw pumps are volumetric self-priming pumps suited to handle oils and liquids with a minimum lubricating quality. The simplicity of the
design makes these pumps intrinsically reliable and efficient. Three screws rotate inside a casing with close tolerances, thus forming sealed
chambers and provoking the axial displacement of the fluid. The idler spindles rotate without contact with the driving spindle because of the fluid
itself, thus being free from radial forces.
The accurate hydraulic balance and the special profile of the screw thread guarantee a continuous flow
with minimum pulsations and turbulance, thus enabling extremely low noise levels even at high rotational
speed.
The screws epicycloidal profiling is developed through a complex computerized calculation which not only
perfectly defines their shape, but also controls the production with continuous monitoring of the machining
process, consequently assuring a high degree of repeatable quality.
The high quality level is guarenteed by a final testing on 100% of the manufactured products.
We place the highest value on quality and we certify it

All Seim products are manufactured and tested in accordance with our ISO 9001 Quality Standard.
Our products are 100% tested either to Seim standards or customer requirements. Certification is
available on request.
Installation and maintenance manuals along with spare parts lists are available in multilingual format.
Seim Industrial Division Manufacturing Program features:

Screw pumps: std according to API 676, for mineral and lubricating oils also fluids with low
lubricating properties (water+oil, HFC, LFO, HFO). Flows up to 5,000 lires per minute and pressure upto
130 bar (200 bar peak).
Motor pump sets: close coupled, AC or DC electric motors.
Pre-assembled systems: with bell-housing and coupling arrangements.
Skid mounted pumps: with or without motor but suitable for horizontal or vertical mounting.
High efficiency Air/Oil Heat Exchangers: upto 14,000 kCal/h (16kW)
Relief valves: Flow rate from 50 to 1,200 litres per minute and pressure up to 40 bar
Lubrication Applications
Lubricating system for: speed variators, turbines, Recirculation and Filtering Applications
gearboxes, papermill machines, hot forming machines COOLING LUBRICATION: deep hole drilling, pipe boring,
Lubrication system for the petrochemical, iron and steel, chip conveyors.
and mining industries as well as shipbuilding. FILTERING: mobile filtering systems, off-line filtering
systems for process machines and machine tools,
hydrualic presses, textile machines, grinding machines
Driving Applications HEAT EXCHANGING: injectors heating for plastic molding
Machine tools, bed traversing machines, heat exchangers.
Hydraulic presses FLUSHING AND BOOSTING: piping systems washing,
Hydraulic units for elevators hydraulic systems flushing, boost circuits.
Hydraulic supporting
Rolling mills Fluids to be pumped
Test benches Hydraulic oils
Sheet metal machines Lubricating oils
Plastic molding machines Diathermic oils
Medical Units Oil-in-water emulsions (min. oil percentage 5%)
Light and heavy fuel oils
Phosphoric esters
II
SCREW PUMPS INTRODUCTION
Built in pressure relief

Close manufacturing tolerances guarantee
valve, on demand high volumetric efficiency and low noise.
Groove ball bearing, lubricated by the fluid
to be pumped (internal pump design).
Epicycloidal profile hydraulically

balanced driving spindle.
A rational and unique technical

solution. Thermal compensation
and hydraulic sealing insert.
Coupling flange (ISO flange
in the standard version).
Maintenance-free unbalanced
Hypocycloidal profile idler spindles
mechanical seal, constantly
maintained at inlet pressure. hydraulically driven by the fluid to
be pumped.
VISCOSITY CHART
O
cS t E SSU SR 1
Characteristics
5 1,39 42 37
Compatible with a wide range of viscosities from
10 1,83 58 51
1 to 12,000 cSt and above.
20 2,87 97 85
Efficiently working also at very low temperatures (-20 OC). 30 4,07 141 123
High self-priming capacity. 40 5,33 185 163
High rotation rates = minimizing the size and cost of the pump. 50 6,62 230 203
Steady flow rate = maximum efficiency in heat exchange 75 9,89 343 304
applications. 100 13,17 456 405
Special design for systems with entrained air in the lubricant 150 19,74 683 608
200 26,3 910 810
= minimizing the vibrations and noise caused by air.
250 32,9 1.137 1.012
Minimum sensitivity to particle pollution = longest life of
300 39,4 1.364 1.215
the pump and circuit.
400 52,6 1.819 1.620
Continuous operating pressures up to 130 bar, peak 200 bar.
500 65,8 2.273 2.024
Pulsation-free = maximum efficiency of filtering applications. 600 78,9 2.727 2.429
Extremely quiet. 800 105,3 3.637 3.239
1.000 131,6 4.546 4.049
1.250 164,5 5.682 5.061
1.500 197,4 6.818 6.073
2.200 290 10.000 8.460
4.400 590 20.000 16.920
III
SCREW PUMPS SCREW PUMP PRODUCT RANGE
Direction of rotation: clockwise for all pumps as seen from the driving side. Bi-directional and reverse rotation pump available depending on series.
S C R E W P U M P P R O D U C T R A N G E
Series PA PC PD A PEA3 PE4 PF PGA PH PO PQJ PU PX
Models (No.) 23 22 7 5 20 15 22 22 12 5 9 22
Delivery Flow (lpm) 3 - 950 10 - 1500 15 - 160 300/1500 10 - 950 10 - 390 10 - 1500 10 - 1500 10 - 280 3 - 30 500/5000 10 - 2400
Maximum Continuous Delivery
50 40 10 50 80 130 60 80 100 10 30 30
Pressure (bar)
Viscosity (cSt) - (1) 10 - 400 10 - 400 20 - 400 10 - 400 10 - 400 10 - 400 1 - 400 5 - 400 1 - 400 10 - 400 10 - 400 10 - 400
Working Temperature (C) - (1) 0 - 120 0 - 120 0 - 100 0 - 120 0 - 120 0 - 120 0 - 60 -20/+160 0 - 60 0 - 100 0 - 120 0 - 120
Rotating Speed (rpm minimum/
750/3500 750/3500 750/3500 750/3500 750/3500 750/3500 1450/3500 750/3500 1450/3500 750/3500 750/1500 750/2900
maximum)
M E D I A C O M P A T I B I L I T Y
Lube & Lubricating Oils + + + + + + O + O + + +
Diathermic Oils + + + + + + +
Fuel Oils O + + + O O
Oil or Glycol Water Emulsion + O + O O
S E R I E S M A I N C H A R A C T E R I S T I C S
Self-priming Capacity + + + + + + + + + + + +
Seal Type (M = mechanical - C = lip) (2) M M M M M M M M C M M
B U I L T - I N R E L I E F V A L V E
Internal Relief O O O O O O O
External Relief O O O O O O
In-Line (VMP) O O O O O O O O O O O
M O U N T I N G
Horiz ontal + + + + + + + + + + +
Vertical + + + + + + + + + + + +
Flanged + + + + + + + + + + O +
On Foot O O O O O O O + O
Tripod O O O O O O O O O
On Base-Plate O O O O O O O O O
Direct Coupling Motor Pump O O
M A T E R I A L S
Casing A A/G A A A A H G H A G G
External Casing C
Main/Idler Screw s N/G N N/G N N N N N N N/G N N/G
O-rings V V V V V V V V V V V
Seal (3) Shaft Z S S S S W (or T) W (or T) W (or T) V W S (or T)
S U C T I O N / D E L I V E R Y P O R T S
B SP + (4) + O O O O O + +
SAE + + + + + + +
DIN O O O O O O + O
ANSI + O O O O O O O
+- Standard execution O- Optional
(1) Viscosity range for standard built pumps, for different functional characteristics please contact
the jbj Techniques Ltd. technical department tel: 01737 767493 or email: info@jbj.co.uk.
(2) Submerged pump.
(3) Other typologies/materials upon request
(4) Optional, with strainer on suction side
Materials
A: Aluminium alloy H: Cast iron + resin insert T: Teflon Z: Silicium carbide/graphite
C: Carbon steel N: Nitrided steel V: Viton
G: Cast iron S: AISI 630 Stainless steel/graphite W: Tungsten carbide/ Tungsten carbide
IV
SCREW PUMPS SCREW PUMP PRODUCT RANGE
Screw Pump displacement, series, number of leads, model code
Pump Series
Inner
Displacement L ead
Screw L ead PA PC PD A PE3 PE4 PF PGA PH PO PQJ PU PX
(cm/rev) C ode
(mm)
Number of Leads
3.3 018 022 A 6 4
4.8 032 B 6 4
6.6 044 C 6 4
9.6 025 034 A 6 4 4 6 4 4 6 3 4
11.8 042 B 6 4 4 6 4 4 6 4
14.1 050 C 6 4 4 6 4 4 6 4
15.9 029 042 A 6 4 2 4 6 4 4 6
18.9 050 B 6 4 2 4 6 4 4 6
22.1 032 048 A 4 4 2 4 6 4 4 6 4
29.5 064 B 4 4 2 4 6 4 4 6 4
40.4 040 056 A 4 4 2 4 6 4 4 6 4
49.0 068 B 4 4 2 4 6 4 4 6 4
57.7 080 C 4 4 2 4 6 4 4 6 4
69.4 045 076 A 4 4 4 6 4 4 6 4
82.1 090 B 4 4 4 6 4 4 6 4
98.2 055 072 A 4 4 4 6 4 4 4
117.2 086 B 4 4 4 6 4 4 4
139.1 102 C 4 4 4 6 4 4 4
165.5 060 102 A 4 4 4 4 4 4
194.7 120 B 4 4 4 4 4 4
233.6 072 100 A 4 3 3 4 4 4 4
280.4 120 B 4 3 3 4 4 4 4
336.4 144 C 4 3 3 4 4 4 4
434.7 083 140 A 3 3 4 4 3
527.8 170 B 3 3 4 4 3
638.0 102 136 A 3 3
788.0 168 B 3 3
975.0 208 C 3 3
1202.0 126 168 A 3 3
1488.0 208 B 3 3
1832.0 256 C 3 3
2281.0 156 208 A 3
2807.0 256 B 3
3421.0 312 C 3
Example of ordering code
PE 040 # 4 A ...
Pump Series Lead Code Length
Central Screw Number of Leads
V
SCREW PUMPS QUICK FLOW SIZE CHART
Quick Flow Siz e Chart
Screw Diameter 018 025 029 032
Code letter A B C A B C A B A B
Displacement (cm3) 3.3 4.8 6.6 9.6 11.8 14.1 15.9 18.9 22.1 29.5
Q@1450 rpm (lpm) 5 7 10 14 17 20 23 27 32 43
Q@2900 rpm (lpm) 10 14 19 28 34 41 46 55 64 86
Screw Diameter 040 045 055 060
Code letter A B C A B A B C A B
Displacement (cm3) 40.4 49 57.7 60.4 82.1 98.2 117 139 165.5 194.7
Q@1450 rpm (lpm) 59 71 84 88 119 142 170 202 240 282
Q@2900 rpm (lpm) 117 142 167 175 238 285 340 403 480 565
Screw Diameter 072 083 102 126 156
Code letter A B C A B A B C A B C A B B
Displacement (cm3) 234 280 336 434.7 527.8 438 788 975 1202 1488 1832 2281 2807 3421
Q@1450 rpm (lpm) 339 407 488 630 765 635 1143 1414 1743 2158 2656 3307 4070 4960
Q@2900 rpm (lpm) 677 813 976 1261 1531 - - - - - - - - -
See page IV for pressure ranges and page V for screw diameters and codes
1
SCREW PUMPS PDA SERIES WITH VALVE
For hydraulic oils, lubricating oils. Admissible delivery pressure (standard valve setting) = 6 bar
Functional Characteristics, Standard Version
Delivery flow 15 to 160 l/min
Admissible delvery pressure* up to 10 bar continuous
Admissible suction pressure -0.4 to 2 bar For different values contact jbj tech. dept.
Kinematics viscosity 20 to 400 cSt For different values contact jbj tech. dept.
Admissible temperature 0 to 100C (32 to 212F) For different values contact jbj tech. dept.
Driving speed 750 to 3600 rpm
Average noise level 56 - 62 dB(A) at 2900 rpm according to pump dimension
Recommended filtration 60 micron max, suction side (not abrasive contaminant) ISO4406 19/16 - NAS10
Direction of rotation clockwise, as seen from the driving side
* Reduced pressure limits apply due to fluid viscosity and driving speed. Consult the performance charts for the individual pump size
For different functional characteristics, please contact the jbj Techniques Ltd. technical department tel: 01737 767493 or email: info@jbj.co.uk.
2
SCREW PUMPS PDA SERIES WITH VALVE
Main field of application: Low pressure lubrication systems, auxiliary filtration systems, cooling systems.
Dimensions in mm (unless otherwise stated)
N P
Size A B C D E F L M T V d1 d2 d3 d4 d5 d6
GAS
PDA029#2..01. 278 82 42 35 5 14 122 39 1" 1" 21.5 6 19 100 125 150 95 11
PDA032#2..01. 278 82 42 35 5 14 122 39 1" 1" 21.5 6 19 100 125 150 95 11
PDA040#2..01. 300 82 42 35 5 14 140 39 1" 1" 21.5 6 19 100 125 150 95 11
3
SCREW PUMPS PX SERIES
For hydraulic oils, lubricating oils. Admissible delivery pressure (continuous) = 30 bar at 2900rpm
Admissible temperature 0 to 120C For different values contact jbj tech. dept
*Standard valve setting mod. A: 0-7 bar mod. B:7 - 16 bar
4
SCREW PUMPS PX SERIES
Main field of application: Industrial purpose, low pressure range: lubrication, cooling and auxiliary filtration systems
*Pump casing and connection flange in aluminium alloy. Inlet flange adjustable to 90 and 180
Size A A1 B C D E F H L L1 M N P T V d1 d2 d3 d4 d5 d6
PX025#6... 310 294.0 65.0 47.5 25 5 10 32.5 178 181 42.0 " 1" 16.0 5 14 100 125 150 80 11
PX032#4... 412 360.0 73.0 75.0 40 5 15 40.5 227 212 60.0 1" 2" 21.5 6 19 125 160 145 100 13
PX040#4... 440 390.0 73.0 75.0 40 5 15 40.5 256 241 60.0 1" 2" 21.5 6 19 125 160 145 100 13
PX045#4... 494 431.5 91.5 81.0 51 5 15 55.5 269 259 75.5 2" 2" 35.0 10 32 125 160 145 135 13
PX055#4... 534 472.0 91.5 82.0 51 5 15 55.5 308 298 75.5 2" 2" 35.0 10 32 125 160 145 135 13
PX060#4... 631 526.5 88.0 83.5 51 5 18 75.0 387 355 100.0 2" 4" 35.0 10 32 160 200 195 170 18
PX072#4... 717 613.0 88.0 101.0 65 5 18 75.0 455 424 100.0 2" 4" 35.0 10 32 160 200 195 170 18
*PX083#3... 785 N.D. 194.0 90.0 80 5 30 95.5 406 N.D. 118.0 4" 5" 48.5 14 45 250 315 365 180 26
The range has been extended to include sizes 102 and 126. Please contact jbj Techniques Ltd. technical department tel: 01737 767493 or
email: info@jbj.co.uk for details.
5
SCREW PUMPS PGA4 SERIES
For cooling lubricants with low viscosity and minimum lubricating properties. Admissible delivery pressure (continuous) = 60 bar at 2900 rpm
Admissible delvery pressure* upto 60 bar continuous at 2900 rpm
Kinematics viscosity 1 to 10 cSt typical and up to 400cSt For different values contact jbj tech. dept.
Driving speed 2900 to 3500 rpm (1450 rpm up to 10 bar)
Recommended filtration 40 micron maximum, suction side (not abrasive contaminant) ISO4406 18/15 - NAS9
6
SCREW PUMPS PGA4 SERIES
Main field of application: Machine tools high pressure cooling systems
N P
Size A B C D E F H L M T V d1 d2 d3 d4 d5 d6
SAE
PGA025#4... 347 120 42 35 5 14 40 150 55 1" 1" 21.5 6 19 100 125 150 105 11
PGA029#4... 347 120 42 35 5 14 40 150 55 1" 1" 21.5 6 19 100 125 150 105 11
PGA032#4... 377 120 42 35 5 14 40 180 55 1" 1" 21.5 6 19 100 125 150 105 11
PGA040#4... 434 128 47 40 5 16 47 221 62 1" 1" 24.5 6 22 125 160 188 118 14
PGA045#4... 484 142 47 40 5 18 53 251 68 1" 2" 27.0 8 24 125 160 188 131 14
PGA055#4... 561 159 62 55 5 20 64 290 82 2" 2" 33.0 8 30 160 200 234 158 18
PGA060#4... 635 172 62 55 5 23 69 343 89 2" 3" 35.0 10 32 160 200 234 172 18
PGA072#4... 768 194 82 75 5 25 79 413 102 3" 4" 41.0 10 38 200 250 292 198 22
PGA083#4... 884 212 90 82 5 30 95 490 118 3" 5" 48.5 14 45 250 315 365 230 26
7
SCREW PUMPS PO SERIES
For cooling lubricants with low viscosity and minimum lubricating properties. Admissible delivery pressure (continuous) = 100 bar at 2900 rpm
Admissible delvery pressure* up to 100 bar continuous at 2900rpm
Admissible suction pressure -0.5 to 10 bar For different values contact jbj tech. dept
Kinematics viscosity 1 to 10 cSt typical and up to 400 cSt For different values contact jbj tech. dept.
8
SCREW PUMPS PO SERIES
Main field of application: Machine tools high pressure cooling systems.
N P
Size A B C D E F L T V d1 d2 d3 d4 d5 d6 d7 d8 d9
SAE
PO025#6... 397 76 43 35 7 15 278 1" 1" 21.5 6 19 100 160 140 136 11 140 160 160
PO029#6... 397 76 43 35 7 15 278 1" 1" 21.5 6 19 100 160 140 136 11 140 160 160
PO032#6... 441 76 43 35 7 15 322 1" 1" 21.5 6 19 100 160 140 136 11 140 160 160
PO040#6... 530 96 49 40 7 15 386 1" 1" 24.5 6 22 125 160 152 178 13 180 215 200
PO045#6... 583 96 49 40 7 15 439 1" 1" 27.0 8 24 125 160 152 178 13 180 215 200
9
SCREW PUMPS PQJ SERIES
Admissible suction pressure -0.2 to 1 bar
Average noise level 56 dB(A) at 2900 rpm
10
SCREW PUMPS PQJ SERIES
Main field of application: Auxiliary lubrication systems. Version with female shaft matching el. Motors size 56 - 71
N P
Size A B C E H L d2 d3 d6 d1 T V
Gas
Version with Female Shaft Female Shaft
9 10.4 3
PQJ018#4...V 173 57 - 4 300 90 " " 70 85 6.5
11 12.8 4
PQJ025#3...V 173 57 - 4 300 90 " " 70 85 6.5 14 16.0 5
Version with Male Shaft Male Shaft
PQJ018#4...V 173 57 30 4 300 90 " " 70 85 6.5 14 16 5
PQJ025#3...V 173 57 30 4 300 90 " " 70 85 6.5 14 16 5
11
SCREW PUMPS PE4 SERIES
For hydraulic oils, lubricating oils. Admissible delivery pressure (continuous) = 80 bar at 2900 rpm
Admissible delvery pressure* up to 80 bar continuous, 120 bar peak at 2900 rpm
Recommended filtration 40 micron max, suction side (not abrasive contaminant) ISO4406 18/15- NAS9
12
SCREW PUMPS PE4 SERIES
Main field of application: Industrial general purpose, middle pressure range.
N P
SAE
PE025#4... 317 101.0 42 35.0 5 14 40 137.0 53 1" 1" 21.5 6 19 100 125 150 95 11
PE029#4... 317 101.0 42 35.0 5 14 40 137.0 53 1" 1" 21.5 6 19 100 125 150 95 11
PE032#4... 347 101.0 42 35.0 5 14 40 167.0 53 1" 1" 21.5 6 19 100 125 150 95 11
PE040#4... 404 112.0 47 40.0 5 16 47 209.0 59 1" 1" 24.5 6 22 125 160 188 108 14
PE045#4... 452 126.0 47 40.0 5 18 52 239.0 63 1" 2" 27.0 8 24 125 160 188 121 14
PE055#4... 526 136.0 62 55.0 5 20 60 278.0 76 2" 2" 33.0 8 30 160 200 234 148 18
PE060#4... 600 151.0 62 55.0 5 23 64 328.0 83 2" 3" 35.0 10 32 160 200 234 162 18
PE072#4... 733 172.5 82 74.5 5 25 79 398.5 96 3" 4" 41.0 10 38 200 250 292 187 22
13
SCREW PUMPS PE4 SERIES with relief valve
For hydraulic oils, lubricating oils. Admissible delivery pressure (standard valve setting) = 7, 16 or 40 bar
*Standard valve setting mod. A: 0 - 7 bar mod. B: 7 - 16 bar mod. C: 16 - 40 bar
14
SCREW PUMPS PE4 SERIES with relief valve
Main field of application: Industrial general purpose, low pressure range.
N P
SAE
PE025#4..H.. 429 101 42 35 5 14 40 151 55 1" 1" 21.5 6 19 100 125 150 105 11
PE029#4..H.. 429 101 42 35 5 14 40 151 55 1" 1" 21.5 6 19 100 125 150 105 11
PE032#4..H.. 459 101 42 35 5 14 40 181 55 1" 1" 21.5 6 19 100 125 150 105 11
PE040#4..H.. 559 112 47 40 5 16 47 222 62 1" 1" 24.5 6 22 125 160 188 118 14
PE045#4..H.. 597 126 47 40 5 18 53 252 68 1" 2" 27.0 8 24 125 160 188 131 14
PE055#4..H.. 705 136 62 55 5 20 64 291 82 2" 2" 33.0 8 30 160 200 234 158 18
PE060#4..H.. 775 151 62 55 5 23 69 344 89 2" 3" 35.0 10 32 160 200 234 172 18
15
SCREW PUMPS PEA3 SERIES
For hydraulic oils, lubricating oils. Admissible delivery pressure (continuous) = 50 bar at 2900 rpm.
Admissible temperature 0 to 120C For different values contact jbj tech. dept.
Driving speed 750 to 3600 rpm (typical 1450 - 1750 rpm)
16
SCREW PUMPS PEA3 SERIES
Main field of application: Industrial general purpose, low and middle pressure range.
N P
SAE
PEA072#3..0.. 676 172 82 75 5 25 80 342 102 3" 4" 41.0 10 38 200 250 292 198 22
PEA083#3..0.. 781 194 90 82 5 30 95 406 118 4" 5" 48.5 14 45 250 315 365 230 26
17
SCREW PUMPS PEA3 SERIES with relief valve
For hydraulic oils, lubricating oils. Admissible delivery pressure (std valve setting) = 7, 16 or 40 bar.
Admissible delvery pressure* upto 40 bar continuous, 75 bar peak at 2900 rpm
*Standard valve setting mod. A: 0 - 7 bar mod. B: 7 16 bar mod. C: 16 - 40 bar
18
SCREW PUMPS PEA3 SERIES with relief valve
Main field of application: Industrial general purpose, low pressure range.
N P
SAE
PEA072#3..H.. 893 172 82 75 5 25 80 342 102 3" 4" 41.0 10 38 200 250 292 198 22
PEA083#3..H.. 999 194 90 82 5 30 95 406 118 4" 5" 48.5 14 45 250 315 365 230 26
19
SCREW PUMPS PC SERIES axial inlet flange
For hydraulic oils, lubricating oils. Admissible delivery pressure (continuous) = 40 bar at 2900 rpm. 30 bar at 1450 rpm
Admissible delvery pressure* upto 30 bar at 1450 rpm, 40 bar at 2900 rpm
20
SCREW PUMPS PC SERIES axial inlet flange
Main field of application: Pumps for lubrication systems and auxilary cooling, with steel body. Customised versions and API 676 ll ed
N P
ANSI 150 RF
PC025#4..A.. 439 101 42 35 5 16 118 264 56 1" 1" 21.5 6 19 125 160 188 133 14
PC029#4..A.. 439 101 42 35 5 16 118 264 56 1" 1" 21.5 6 19 125 160 188 133 14
PC032#4..A.. 445 101 42 35 5 16 118 302 62 1" 1" 21.5 6 19 125 160 188 133 14
PC040#4..A.. 504 112 47 40 5 20 133 344 62 1" 1" 24.5 6 22 160 200 234 150 18
PC045#4..A.. 557 126 47 40 5 23 125 384 63 1" 2" 27.0 8 24 160 200 234 168 18
PC055#4..A.. 649 136 62 55 5 25 153 451 70 2" 3" 33.0 8 30 200 250 292 194 22
PC060#4..A.. 726 151 62 55 5 28 150 468 70 3" 3" 35.0 10 32 200 250 292 219 22
PC072#3..A.. 806 172 82 75 5 30 184 552 76 3" 4" 41.0 10 38 250 315 365 244 26
PC083#3..A.. 934 194 90 82 5 36 202 650 89 4" 5" 48.5 14 45 250 315 365 273 26
21
SCREW PUMPS PC SERIES radial inlet flange
For hydraulic oils, lubricating oils. Admissible delivery pressure (continuous) = 40 bar at 2900 rpm. 30 bar at 1450 rpm
Admissible delvery pressure* up to 30 bar at 1450 rpm, 40 bar at 2900 rpm
Admissible suction pressure* -0.5 to 10 bar For different values contact jbj tech. dept.
22
SCREW PUMPS PC SERIES radial inlet flange
Main field of application: Pumps for lubrication systems and auxilary cooling, with steel body. Customised versions and API 676 11 ed
N P
Size A B C D E F H1 H2 L M T V d1 d2 d3 d4 d5 d6
ANSI 150 RF
PC025#4..R.. 370 101 42 35 5 16 118 122 167 120 1" 1" 21.5 6 19 125 160 188 133 14
PC029#4..R.. 370 101 42 35 5 16 118 122 167 120 1" 1" 21.5 6 19 125 160 188 133 14
PC032#4..R.. 370 101 42 35 5 16 118 122 167 124 1" 1" 21.5 6 19 125 160 188 133 14
PC040#4..R.. 429 112 47 40 5 20 133 133 209 133 1" 1" 24.5 6 22 160 200 234 150 18
PC045#4..R.. 481 126 47 40 5 23 135 135 239 143 1" 2" 27.0 8 24 160 200 234 168 18
PC055#4..R.. 560 136 62 55 5 25 153 154 278 157 2" 3" 33.0 8 30 200 250 292 198 22
PC060#4..R.. 637 151 62 55 5 28 159 159 284 171 3" 3" 35.0 10 32 200 250 292 219 22
PC072#3..R.. 711 172 82 75 5 30 184 184 326 186 3" 4" 41.0 10 38 250 315 365 244 26
PC083#3..R.. 826 194 90 82 5 36 202 202 235 208 4" 5" 48.5 14 45 250 315 365 273 26
23
SCREW PUMPS PH4 SERIES
For fuel oils at low or high viscosity and lubricating oil at high and low temperature. Admissible delivery pressure (continuous) = 80 bar at 2900rpm
Admissible delvery pressure* up to 80 bar continuous at 2900 rpm, 120 bar peak
Kinematics viscosity 5 to 10 cSt typical and up to 400 cSt For different values contact jbj tech. dept.
Admissible temperature 0 to 120C
Driving speed 750 to 3500 rpm (750 - 1450 rpm MAX up to 10 bar)
24
SCREW PUMPS PH4 SERIES
Main field of application: Burners - fuel supply line. Lubrication circuits at high temperature.
Inlet flange adjustable to 90 and 180
N P
SAE
PH025#4... 347 120 42 35 5 14 40 150 55 1" 1" 21.5 6 19 100 125 150 105 11
PH029#4... 347 120 42 35 5 14 40 150 55 1" 1" 21.5 6 19 100 125 150 105 11
PH032#4... 377 120 42 35 5 14 40 180 55 1" 1" 21.5 6 19 100 125 150 105 11
PH040#4... 434 128 47 40 5 16 47 221 62 1" 1" 24.5 6 22 125 160 188 118 14
PH045#4... 484 142 47 40 5 18 53 251 68 1" 2" 27 8 24 125 160 188 131 14
PH055#4... 561 159 62 55 5 20 64 290 82 2" 2" 33 8 30 160 200 234 158 18
PH060#4... 635 172 62 55 5 23 69 343 89 2" 3" 35 10 32 160 200 234 172 18
PH072#4... 768 194 82 75 5 25 79 413 102 3" 4" 41 10 38 200 250 292 198 22
PH083#4... 884 212 90 82 5 30 95 490 118 3" 5" 48.5 14 45 250 315 365 230 26
25
SCREW PUMPS PF6 SERIES balanced idlers
For hydraulic oils, lubricating oils. Admissible delivery pressure (continuous) = 130 bar @ 29000 rpm.
Admissible delvery pressure* up to 130 bar continuous, 200 bar peak at 2900 rpm.
26
SCREW PUMPS PF6 SERIES balanced idlers
Main field of application: Industrial general purpose, high pressure range.
N P
SAE
PF025#6... 367 101 42 35 5 14 40 187 53 1" 1" 21.5 6 19 100 125 150 95 11
PF029#6... 367 101 42 35 5 14 40 187 53 1" 1" 21.5 6 19 100 125 150 95 11
PF032#6... 411 101 42 35 5 14 40 231 53 1" 1" 21.5 6 19 100 125 150 95 11
PF040#6... 484 112 47 40 5 16 47 289 59 1" 1" 27.0 8 24 125 160 188 108 14
PF045#6... 542 126 47 40 5 18 52 329 63 1" 2" 31.0 8 28 125 160 188 121 14
PF055#6... 628 136 62 55 5 20 60 380 76 2" 2" 35.0 10 32 160 200 234 148 18
27
SCREW PUMPS PU SERIES axial inlet flange
28
SCREW PUMPS PU SERIES axial inlet flange
Main field of application: Large delivery flow pumps in auxilary cooling or lubrication systems.
Customised versions and versions with pressure relief valve available on request.
Size A B C D E F H L N P T V d1 d2 d3 d4 d5 d6
DN 125 DN 200
PU102#3..A.. 966 207 148 77 5 25 112 611 41 10 38 200 250 292 219 22
PN40 PN16
DN 200 D 200
PU126#3..A.. 1137 225 158 83 5 30 130 754 45 12 42 250 315 365 273 26
PN40 PN16
DN 200 DN250
PU156#3..A.. 1495 272 200 110 5 30 160 1023 59 16 59 250 315 365 368 26
PN40 PN10
29
SCREW PUMPS PU SERIES radial inlet flange
30
SCREW PUMPS PU SERIES radial inlet flange
Main field of application: Large delivery flow pumps in auxilary cooling or lubrication systems.
Size A B C D E F H L M N P T V d1 d2 d3 d4 d5 d6
DN 125 DN 150
PU102#3..R.. 911 207 148 77 5 25 112 450 200 41 10 38 200 250 292 219 22
PN40 PN16
DN 150 D 200
PU126#3..R.. 1074 225 158 83 5 30 130 558 240 45 12 42 250 315 365 273 26
PN40 PN16
DN 200 DN250
PU156#3..R.. 1425 272 200 110 5 30 160 783 340 59 16 55 250 315 365 368 26
PN40 PN10
31
SCREW PUMPS PAV SERIES with bellhousing
For hydraulic oils, lubricating oils. Admissible delivery pressure 75 bar at 2900 rpm
Admissible suction pressure* submerged in oil
Average noise level 56 dB(A) at 2900 rpm
32
SCREW PUMPS PAV SERIES with bellhousing
Main field of application: Oil submerged pump for hydraulic power packs.
B H L P R S T V d1 d2 d3 d4 d5 d6 d7 d8 d9 d10
Size
Gas
PA018#6 . . .
93 246 42 " 18 33.5 27 8 24 130 105 200 165 63 M10 M10 10.5 140
PA025#4 . . .
33
SCREW PUMPS PA SERIES with strainer
For hydraulic oils, lubricating oils. Admissible delivery pressure (continuous) = 50 bar at 2900 rpm. ISO 3019/2 motor connection.
Admissible suction pressure submerged in oil
34
SCREW PUMPS PA SERIES with strainer
Main field of application: Pump submersible into tank for lubrication systems, auxilary filtration system, cooling system.
P
Size A B C D E G H L R S T V d1 d2 d3 d4
GAS
PA025#6.OM 299 68 42 35 22 229 256 30 1" 44 24 21.5 6 19 83
PA029#6.OM 299 68 42 35 22 229 256 30 1" 44 24 21.5 6 19 83
PA032#4.OM 299 68 42 35 22 229 256 30 1" 44 24 21.5 6 19 125 188 83
PA040#4.OM 342 68 42 35 22 272 299 50 1" 50 24 21.5 6 19 123
PA045#4.OM 363 68 48 40 22 297 314 65 1" 50 20 27.0 10 24 123
PA055#4.OM 425 86 63 55 22 337 358 50 1" 60 28 35.0 10 32 162
PA060#4.OM 464 86 63 57 22 390 401 50 2" 60 28 35.0 10 32 160 234 162
PA072#4.OM 563 112 63 63 22 452 500 130 2" 72 30 41.0 10 38 190
35
SCREW PUMPS PA SERIES axial inlet flange
For hydraulic oils, lubricating oils. Admissible delivery pressure (continuous) = 50 bar at 2900 rpm. ISO 3019/2 motor connection.
36
SCREW PUMPS PA SERIES axial inlet flange
Main field of application: Submersible pump for lubrication systems, auxilary filtration systems, cooling systems.
P Q
Size A B C D E H R S T V d1 d2 d3 d4
GAS
PA025#6.0T 318 68 42 35 22 276 1" 1" 44 24 21.5 6 19 81
PA029#6.0T 318 68 42 35 22 276 1" 1" 44 24 21.5 6 19 81
PA032#4.0T 318 68 42 35 22 276 1" 1" 44 24 21.5 6 19 125 188 81
PA040#4.0T 372 68 42 35 22 330 1" 2" 50 24 21.5 6 19 149
PA045#4.0T 378 68 48 40 22 330 1" 2" 50 27 27.0 10 24 149
PA055#4.0T 470 86 63 55 22 407 1" 3" 60 28 35.0 10 32 190
PA060#4.0T 514 86 63 57 22 451 2" 3" 60 30 35.0 10 32 160 234 190
PA072#4.0T 600 112 63 63 22 537 2" 4" 72 30 41.0 10 38 250
37
SCREW PUMPS PRESSURE RELIEF VALVE - VMP
For hydraulic oils, lubricating oils, fuel oils and cooling lubricants emulsions.
Delivery flow 30 - 1200 l/min
Maximum pressure* see dimensional chart
38
SCREW PUMPS PRESSURE RELIEF VALVE - VMP
Functional draw
Pressure Inlet Outlet

Delivery Flow M S
Size (Setting range) L1 L2 L3 L4
l/min
Bar SAE
VMP#030A 0-7
VMP#030B 30 - 300 7 - 16 1" 1" 90 50 100 208
VMP#030C 16 - 40
VMP#042A 0-7 260
VMP#042B 100 - 600 7 - 16 2" 2" 110 70 125 285
VMP#042C 16 - 40 285
VMP#060A 0-7 352
VMP#060B 200 - 1200 7 - 16 3" 3" 142 90 165 382
VMP#060C 16 - 40 382
39
SCREW PUMPS DIRECT COUPLING MOTOR PUMPS MD SERIES
Main field of application: Low pressure lubrication systems, auxilary filtration systems, cooling systems and many others.
Typical section and components
Motor/Pump Information
Fluid to be Pumped i.e. mineral oil ISO VG 32
Cold start temperature
Working temperature
Other relevant fluid information i.e. trade name
Pump output required lpm @ . . . bar
Pump to have built in relief valve yes/no
Application i.e. cooling circuit
Environment considerations i.e. explosion proof
Mounting orientation i.e. horizontal
Installation standard i.e. ANSI, NEMA, DIN, API
Voltage, poles, Hz. when tested, when installed
Special motor requirements i.e. drip proof
Delivery requirements
Certification
We can offer accessories such as SAE flanges, tripods, foot brackets, noise damping equipment, line relief valves
We can complete your system with air/oil coolers, shell/tube coolers, plate coolers both gasket and brazed, level switches and much more.
Please contact the jbj Techniques Ltd. technical department tel: 01737 767493 or email: info@jbj.co.uk for further details.
jbj Techniques Limited can supply any screw pumps complete with motors etc.
For full details, please contact the jbj Techniques Ltd. technical department tel: 01737 767493 or email: info@jbj.co.uk.
40
Gear Pumps/Motors Mini Power Packs Screw Pumps LSHT Motors/Geared Motors Coolers BD Clutches & Gearboxes BDS Clutches
Planetary Gearboxes Marine Gearboxes Splitter Gearboxes Hydraulic Adaptors Torsional Couplings Pressure Intensifiers Bellhousings
quality products for mechanical & fluid power
www.jbj.co.uk/productlist.html
Torsionally Flexible Couplings Torsionally Rigid Couplings FD20 Data Logging Device
Torque Limiting Couplings Dampers Tanks/Accessories ATEX Approved Flanges Engine Adaptor Kits Flow Dividers

JBJ Techniques LTD Screw Pumps

Uploaded by

Copyright:

Available Formats

JBJ Techniques LTD Screw Pumps

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

JBJ Techniques LTD Screw Pumps

Uploaded by

Copyright:

Available Formats

01

Product list ...................................................................................................................................................................................... I

Introduction ..................................................................................................................................................................................... II - III

Screw Pump Range ....................................................................................................................................................................... IV - V

Quick Flow Size Chart .................................................................................................................................................................. 1

PDA Series with valve .................................................................................................................................................................. 2 - 3

PGA4 Series .................................................................................................................................................................................... 6 - 7

PQJ Series ...................................................................................................................................................................................... 10 - 11

PE4 Series ....................................................................................................................................................................................... 12 - 13

PE4 Series with relif valve ........................................................................................................................................................... 14 - 15

PEA3 Series .................................................................................................................................................................................... 16 - 17

PEA3 Series with relief valve ...................................................................................................................................................... 18 - 19

PC Series with axial inlet flange ................................................................................................................................................. 20 - 21

PC Series with radial inlet flange ................................................................................................................................................ 22 - 23

PH4 Series ....................................................................................................................................................................................... 24 - 25

PF6 Series balanced idlers .......................................................................................................................................................... 26 - 27

PU Series with axial inlet flange ................................................................................................................................................. 28 - 29

PU Series with radial inlet flange ................................................................................................................................................ 30 - 31

PAV Series with bellhousing ......................................................................................................................................................... 32 - 33

PA Series with strainer ................................................................................................................................................................. 34 - 35

PA Series with axial inlet flange .................................................................................................................................................. 36 - 37

VMP Pressure relief valve ........................................................................................................................................................... 38 - 39

MD Series - Direct Coupling Motor Pumps .............................................................................................................................. 40

We place the highest value on quality and we certify it

Seim Industrial Division Manufacturing Program features:

Built in pressure relief

Epicycloidal profile hydraulically

A rational and unique technical

Series PA PC PD A PEA3 PE4 PF PGA PH PO PQJ PU PX

Lube & Lubricating Oils + + + + + + O + O + + +

Oil or Glycol Water Emulsion + O + O O

Seal Type (M = mechanical - C = lip) (2) M M M M M M M M C M M

Direct Coupling Motor Pump O O

+- Standard execution O- Optional

Screw Pump displacement, series, number of leads, model code

3.3 018 022 A 6 4

9.6 025 034 A 6 4 4 6 4 4 6 3 4

15.9 029 042 A 6 4 2 4 6 4 4 6

22.1 032 048 A 4 4 2 4 6 4 4 6 4

40.4 040 056 A 4 4 2 4 6 4 4 6 4

69.4 045 076 A 4 4 4 6 4 4 6 4

98.2 055 072 A 4 4 4 6 4 4 4

165.5 060 102 A 4 4 4 4 4 4

233.6 072 100 A 4 3 3 4 4 4 4

434.7 083 140 A 3 3 4 4 3

638.0 102 136 A 3 3

1202.0 126 168 A 3 3

2281.0 156 208 A 3

Example of ordering code

Pump Series Lead Code Length

Central Screw Number of Leads

Quick Flow Siz e Chart

Screw Diameter 018 025 029 032

Q@1450 rpm (lpm) 5 7 10 14 17 20 23 27 32 43

Q@2900 rpm (lpm) 10 14 19 28 34 41 46 55 64 86

Screw Diameter 040 045 055 060

Q@1450 rpm (lpm) 59 71 84 88 119 142 170 202 240 282

Screw Diameter 072 083 102 126 156

Q@2900 rpm (lpm) 677 813 976 1261 1531 - - - - - - - - -