Cat Cpcaball

BALL
VALVES
APOLLO BALL VALVE
NUMBERING SYSTEM
APOLLO NUMBERING SYSTEM FORMULA: 70 - 105 - 01
XX - X X X - XX
SERIES CONFIGURATION VARIATIONS SIZE* OPTIONS
32 Bronze Ball Valve, Regular-Port, NPT 1 = FNPT 4 = 316 Stainless Steel 1 = 1/4 -01 = Standard
50 Bronze Gas Valve, CSA & UL Listed 2 = Solder Ball & Stem 2 = 3/8 -02 = Grounded
51 Bronze Gas Valve, CSA 3 = Union End NPT 9 = Pinned Retainer 3 = 1/2 -04 = 2-1/4 Stem extension
6PLF Lead Free Cast Iron, Ball Valve, Full-Port, 6 = 3-Way NPT 4 = 3/4 -07 = Tee Handle
Flanged, International 7 = Full-Port Refrigeration Valves 5 = 1 -08 = 90 Reversed Stem
8 = Male X FNPT 6 = 1-1/4 -10 = Stainless Steel Lever & Nut
9 = 3-Way Solder 7 = 1-1/2 -11 = Therma-Seal Insulating Handle
70 Bronze Ball Valve 8 = 2 -12 = Stamped 157 SWP & Bagged
70HC Bronze Ball Valve with Hose Cap 9 = 2-1/2 -13 = Stamped 157 SWP
70LF Lead Free** Bronze Ball Valve 0 = 3 -14 = Side Vented Ball (uni-directional)
70LFHC Lead Free** Bronze Ball Valve with Hose Cap A = 4 -15 = Round Handle, Steel
71 Bronze Ball Valve with Pads -16 = Chain Lever - Vertical
75 Bronze Ball Valve, Std. Port, Padlocking -17 = Rough Chrome Plated
77 Bronze Full-Port Ball Valve -18 = Plain Yellow Grip
77C Bronze Ball Valve, Full Port, Contractor Grade -19 = Lock Plate
77CLF Lead Free** Bronze Ball Valve, Full Port -20 = Slot Vented Ball (bi-directional)
77D Bronze Ball Valve, Full Port, Direct Mount *BODY SIZE WHEN ENDS ARE MIXED. -21 = UHMWPE Trim (non-PTFE)
for Actuators -24 = Graphite Packing
77F Brass Ball Valve, Full Port, USA NOTE: NOT ALL VARIATIONS AND FEATURES ARE AVAILABLE -27 = Stainless Steel Latch-Lock Lever & Nut
77FLF Lead Free** Brass Ball Valve, Full Port ON SAME VALVE. CONSULT CONBRACO REPRESENTATIVE. -30 = Cam-Lock and Grounded
77V APOLLOXPRESS Brass Ball Valve -32 = Stainless Steel Tee Handle & Nut
77VLF Lead Free** APOLLOXPRESS Brass Ball Valve -35 = VTFE Trim (PTFE)
77W Bronze BV, Full Port, APOLLOXPRESS ** LEAD FREE: The wetted surfaces of this product shall -36 = Stainless Steel Hi-Rise Round
77WLF Lead Free ** Bronze BV, Full Port, APOLLOXPRESS contain no more than 0.25% lead by weighted average. Handle, Stainless Steel Nut
78 Specialty Valves Complies with Federal Public Law 111-380. ANSI 3rd party -39 = SS Hi-rise Locking Round Handle,
79 Refrigerant Ball Valves approved and listed. SS Nut
77B Bronze Ball Valve, Side Tap -40 = Cyl-Loc and Grounded
7K Bronze Ball Valve, with Drain -41 = Automatic Drain
80 Bronze Ball Valve, UL Listed -45 = Less Lever and Nut
82 Bronze Three-Piece Full-Port Ball Valve -46 = Latch-Lock Lever - Lock in Closed
82LF Lead Free** Bronze Three-Piece Full-Port Position Only
9A Bronze, Unibody, Heavy Pattern -47 = SS Oval Latch-Lock Handle & Nut
90 Bronze, Unibody, UL Listed Ball Valve -48 = SS Oval Handle (No Latch) & Nut
94A Brass, Full-Port, UL Listed, International -49 = Assembled Dry
94ALF-A Lead Free** Brass, Full Port, International -50 = 2-1/4 Carbon Steel Locking Stem Extension
94MBV Brass Mini-Ball Valve, Std. Port, International -56 = Multifill Seats & Packing
94XLF Lead Free** Brass Ball Valve, PEX, Intl -57 = Oxygen Cleaned
94VLF Lead Free** Brass Press Ball Valve, Intl -58 = Chain Lever - Horizontal
95ALF Lead Free** Brass Stop & Waste Valve, Intl -59 = SS External Trim - 3-pc. Valves & Flange
-60 = Grounded Ball & Stem
-62 = Body Center Section (82 Series)
-63 = NPT x Solder (-100-63-NPT Body;
-200-63-Sweat Body)
-64 = 250 SWP
-65 = Multifill Seats & Graphite Packing
-72 = RTFE Packing
-91 = Locking SS Tee (3/4 and 1)
-92 = Balancing Stop
-94 = -04 & Balancing stop
-BC = Ball Check
-HC = Hose Thread and Cap Option
-SV = Safety vent - 77-100/7K-100 series
(Auto drain)
-SW = Limit switch mounted
-TH = Tested, Hydrostatic
-TC = Tested, Hydrostatic, w/certification
-TW = Tested, Hydrostatic, w/witness
and certification
14
Customer Service (704) 841-6000 www.apollovalves.com
BALL VALVES
contractor series valves
77C-100/200-A SERIES CONTRACTOR SERIES FULL PORT BRONZE BALL VALVE WITH SOLID BALL
Apollos solid ball design delivers true full-port performance with 100 percent
American construction. New for 2016, next generation mod -A adds a new
beefier lever, simplified packing adjustment, wider seats and stem packing
and a 150 SWP body marking.
FEATURES
ASTM grade bronze castings
Solid brass ball, plated
600 psig CWP, non-shock
150 SWP steam rating
Generous RPTFE seats and stem packing
E
Adjustable stem packing
Blow-out proof stem design
Vacuum service to 29 in. Hg
D
O A
Full-port design through 2-1/2

ANSI B16.18 solder end version available as 77C-200 Series
B
CSAB51-CRN
C
Proudly made in USA
E OPTIONS*
2-1/4 stem extension (-04)
O A
CS tee handle (-07)
D
Therma-Seal insulating tee handle (-11)

SS Latch-lock handle (-27),
O G
F
Stem extension and balancing stop (-94)
Reversible handle option
B
E
C
SS vented ball and stem(77C140 and 77C240 series)

NOTE: This drawing and the subject matter disclosed therein is the property of Conbraco Industries, Inc. and is not to be
copied, used, appropriated or disclosed to others without the expressed written permission of Conbraco Industries, Inc.
77C-ULA UL258 Fire Protection Trim & Drain option
REV. CHANGE DESCRIPTION ECN NO. BY DATE
D
O A NAME:
R
MAT'L:
EXP. NO. SCALE: DRN: DATE:

CHKD:
Other handle options available
APP'D: NO. REV.
Also available in a Lead Free version as the 77CLF Series.

* Lever option kits for the 77C and 77C-A models differ. Refer to the latest Apollo kit listing or
B
contact Apollo Tech Support for assistance.
C
E Model Size Dimensions (in.) Wt.

CV
Number (in.) A B C D E F G (lbs.)
O A
Threaded Connection
D
77C-101-01A 1/4 0.37 .095 1.80 1.62 2.86 - - 5 0.6

77C-102-01A 3/8 0.37 1.07 1.86 1.62 2.86 - - 7 0.5
O G
F
77C-103-01A 1/2" 0.50 1.15 2.29 1.79 3.74 - - 16 0.6
B
C
77C-104-01A 3/4" 0.75 1.32 2.67 2.00 4.88 - - 36 1.0
77C-105-01A 1" 1.00 1.53 3.24 2.19 4.88 - - 68 1.8
NAME:
77C-106-01A
REV. CHANGE DESCRIPTION
1-1/4"
ECN NO. BY DATE
1.25 2.04 3.75 3.13 7.06 - - 125 4.4
77C-107-01A 1-1/2" 1.50 2.12 4.11 3.29 7.06 - - 177 4.6
R
MAT'L:
EXP. NO. SCALE: DRN: DATE: CHKD: APP'D: NO. REV.
77C-108-01A 2" 2.00 2.43 4.85 3.83 7.06 - - 389 8.1

77C-109-01A 2-1/2" 2.50 3.12 6.02 4.51 8.06 - - 503 16.2
Solder Connection
*77C-202-01A 3/8" 0.37 1.25 2.18 1.65 2.86 0.41 0.50 16 0.6
77C-203-01A 1/2" 0.50 1.41 2.47 1.79 3.74 0.50 0.63 16 0.6
77C-204-01A 3/4" 0.75 1.64 3.2 2.00 4.88 0.75 0.88 36 1.0
77C-205-01A 1" 1.00 1.92 3.81 2.19 4.88 0.91 1.13 68 1.6
77C-206-01A 1-1/4" 1.25 2.36 4.21 3.13 7.06 0.97 1.38 125 3.9
77C-207-01A 1-1/2" 1.50 2.63 4.91 3.29 7.06 1.09 1.63 177 4.3
77C-208-01A 2" 2.00 3.17 6.07 3.83 7.06 1.37 2.13 389 7.6
77C-209-01A 2-1/2" 2.50 3.77 7.17 4.51 8.06 1.48 2.63 503 15.9
*avalable soon
15
For additional information, submittal sheets and manuals, visit www.apollovalves.com
BALL VALVES
contractor series valves
77CLF-100/200 SERIES CONTRACTOR SERIES FULL PORT LEAD FREE BRONZE BALL VALVE WITH SOLID BALL
Apollos solid ball design delivers true full-port performance with 100 percent
American construction. New for 2016, next generation mod -A adds a new
beefier lever, simplified packing adjustment, wider seats and stem packing
and a 150 SWP body marking.
FEATURES
ASTM grade EZ-SolderTM lead free bronze
Solders just like standard bronze
E
Generous RPTFE seats and stem packing
Solid brass ball, plated
D
O A
Full-port design through 2-1/2

NSF/ANSI 61 Water Quality
B
C
NSF/ANSI 372 Lead Free
IAPMO
E
CSAB51-CRN
Proudly made in USA
O A
OPTIONS*
D

O G
CS tee handle (-07)

B
F Therma-Seal insulating tee handle (-11)
C
E
SS Latch-lock handle (-27),
Stem extension and balancing stop (-94)
Reversible handle option
copied, used, appropriated or disclosed to others without the expressed written permission of Conbraco Industries, Inc. REV. CHANGE DESCRIPTION ECN NO. BY DATE
NAME:
R
MAT'L:
SS vented ball and stem(77CLF140-A and 77CLF240-A series)

D
O A
Other handle options available

* Lever option kits for the 77CLF and 77CLF-A models differ. Refer to the latest Apollo kit listing
B
or contact Apollo Tech Support for assistance.
C
LF Model Size Dimensions (in.) Wt.

E
CV
Number (in.) A B C D E F G (lbs.)
Threaded Connection
O A
D
77CLF-101-01A 1/4 0.37 .095 1.80 1.62 2.86 - - 5 0.6

77CLF-102-01A 3/8 0.37 1.07 1.86 1.62 2.86 - - 7 0.5
O G
77CLF-103-01A 1/2" 0.50 1.15 2.29 1.79 3.74 - - 16 0.6

F
B
77CLF-104-01A 3/4" 0.75 1.32 2.67 2.00 4.88 - - 36 1.0
C
77CLF-105-01A 1" 1.00 1.53 3.24 2.19 4.88 - - 68 1.8

77CLF-106-01A 1-1/4"
REV. CHANGE DESCRIPTION ECN NO. BY DATE 1.25 2.04 3.75 3.13 7.06 - - 125 4.4
NAME:
R
MAT'L: 77CLF-107-01A 1-1/2" 1.50 2.12 4.11 3.29 7.06 - - 177 4.6
77CLF-108-01A 2" 2.00 2.43 4.85 3.83 7.06 - - 389 8.1
77CLF-109-01A 2-1/2" 2.50 3.12 6.02 4.51 8.06 - - 503 16.2

Solder Connection
*77CLF-202-01A 3/8" 0.37 1.25 2.18 1.65 2.86 0.41 0.50 16 0.6
77CLF-203-01A 1/2" 0.50 1.41 2.47 1.79 3.74 0.50 0.63 16 0.6
77CLF-204-01A 3/4" 0.75 1.64 3.2 2.00 4.88 0.75 0.88 36 1.0
77CLF-205-01A 1" 1.00 1.92 3.81 2.19 4.88 0.91 1.13 68 1.6
77CLF-206-01A 1-1/4" 1.25 2.36 4.21 3.13 7.06 0.97 1.38 125 3.9
77CLF-207-01A 1-1/2" 1.50 2.63 4.91 3.29 7.06 1.09 1.63 177 4.3
77CLF-208-01A 2" 2.00 3.17 6.07 3.83 7.06 1.37 2.13 389 7.6
77CLF-209-01A 2-1/2" 2.50 3.77 7.17 4.51 8.06 1.48 2.63 503 15.9
*avalable soon
16
BALL VALVES
general purpose valves
70-100/200 SERIES BRONZE BALL VALVE

The Apollo 70 series is the most widely used and trusted bronze ball valve
in the industry. It features blowout-proof stem, RPTFE seats and stuffing box
ring and plated brass ball.
FEATURES
Heavy pattern construction
Rated 600 psig CWP, non-shock
150 psig for saturated steam
100% tested
Adjustable packing gland
Multiple options and configurations available (see pages 22-23)
Lead Free option (70LF)
Made in USA
Model Size Dimensions (in.)*

Number (in.) A B C
Threaded Connections
70-101-01 1/4 0.37 1.03 2.06
70-102-01 3/8 0.37 1.03 2.06
70-103-01 1/2 0.50 1.12 2.25
70-104-01 3/4 0.68 1.50 3.00
70-105-01 1 0.87 1.68 3.37
70-106-01 1-1/4 1.00 2.00 4.00
70-107-01 1-1/2 1.25 2.18 4.37
70-108-01 2 1.50 2.34 4.68
70-109-01A 2-1/2 2.00 3.12 6.25
70-100-01 3 2.50 3.37 6.75
70-10A-01 4 3.12 3.68 7.37
* Body only. Total will vary with handle and end connection options. Contact Conbraco
Customer Service for additional dimensions.
NOTE: 1/4, 3/8, and 1/2 are full port.
Model Size Dimensions (in.)*

Number (in.) A B C D E F G
Solder Connections
70-202-01 3/8 0.37 1.28 2.56 1.75 3.87 0.505 0.37
70-203-01 1/2 0.50 1.43 2.87 1.75 3.87 0.63 0.50
70-204-01 3/4 0.68 1.93 3.87 2.12 4.87 0.88 0.75
70-205-01 1 0.87 2.25 4.50 2.25 4.87 1.13 0.90
70-206-01 1-1/4 1.00 2.31 4.62 2.62 5.50 1.38 0.96
70-207-01 1-1/2 1.25 2.62 5.25 3.06 8.00 1.63 1.09
70-208-01 2 1.50 3.18 6.37 3.25 8.00 2.13 1.34
70-209-01A 2-1/2 2.00 3.74 7.51 3.72 8.00 2.63 1.48
70-200-01 3 2.50 4.12 8.25 4.12 8.00 3.13 1.67
70-20A-01 4 3.12 4.61 9.22 5.22 9.94 4.13 2.16
* Based on 70-200-01 Dimensions may vary with options.
Soldering temperature: 500F or less
17
BALL VALVES
70LF-100/200 SERIES LEAD FREE BRONZE BALL VALVE

The Apollo 70LF series is the most widely used and trusted lead free bronze
ball valve in the industry. It features blowout-proof stem, RPTFE seats and
stuffing box ring and plated brass ball.
FEATURES
Heavy pattern construction
EZ-SolderTM Lead Free Bronze
Solders just like standard bronze
100% factory tested
NSF/ANSI 61-G Water Quality
Multiple options and configurations available (see pages 22-23)
LF Model Size Dimensions (in.)*

Number (in.) A B C
Threaded Connections
70LF-101-01 1/4 0.37 1.03 2.06
70LF-102-01 3/8 0.37 1.03 2.06
70LF-103-01 1/2 0.50 1.12 2.25
70LF-104-01 3/4 0.68 1.50 3.00
70LF-105-01 1 0.87 1.68 3.37
70LF-106-01 1-1/4 1.00 2.00 4.00
70LF-107-01 1-1/2 1.25 2.18 4.37
70LF-108-01 2 1.50 2.34 4.68
70LF-109-01A 2-1/2 2.00 3.12 6.25
70LF-100-01 3 2.50 3.37 6.75
70LF-10A-01 4 3.12 3.68 7.37
* Body only. Total will vary with handle and end connection options. Contact Conbraco
Customer Service for additional dimensions.
LF Model Size Dimensions (in.)*

Solder
70LF-202-01 3/8 0.37 1.28 2.56 1.75 3.87 0.505 0.37
70LF-203-01 1/2 0.50 1.43 2.87 1.75 3.87 0.63 0.50
70LF-204-01 3/4 0.68 1.93 3.87 2.12 4.87 0.88 0.75
70LF-205-01 1 0.87 2.25 4.50 2.25 4.87 1.13 0.90
70LF-206-01 1-1/4 1.00 2.31 4.62 2.62 5.50 1.38 0.96
70LF-207-01 1-1/2 1.25 2.62 5.25 3.06 8.00 1.63 1.09
70LF-208-01 2 1.50 3.18 6.37 3.25 8.00 2.13 1.34
70LF-209-01A 2-1/2 2.00 3.74 7.51 3.72 8.00 2.63 1.48
70LF-200-01 3 2.50 4.12 8.25 4.12 8.00 3.13 1.67
70LF-20A-01 4 3.12 4.61 9.22 5.22 9.94 4.13 2.16
* Based on 70-200-01 Dimensions may vary with options.
Soldering temperature: 500F or less
18
BALL VALVES
70-HC SERIES CAP & CHAIN VALVE WITH 3/4 INCH HOSE CONNECTION, HEAVY BRASS CAP
AND REVERSE HANDLE
Ideally suited for draining or sampling of HVAC or potable water systems, these
valves allow direct connections to hoses. Valve features a securely attached cover
(includes chain) which prevents damage to hose threads. -200 model designed for
soft soldering into lines without disassembly.
FEATURES OPTIONS
Heavy pattern construction Therma-Seal insulating lever
Reverse lever is standard for option (-11)
easier installation Stainless Steel ball and stem
Stainless steel lever & nut option (70-24X-HC/70LF-24X-HC)
standard 70LF is NSF 61 and NSF 372
NPT and solder connections certified Lead Free
EZ-SolderTM Lead Free Bronze
ASTM B584 Bronze
Blowout-proof stem design
RPTFE seats and stuffing box ring
Vacuum Service to 29 in. Hg
Maximum pressure: 600 psi CWP
Temperature rating: 200F
Full pressure rated brass hose cap
Model LF Model Size Dimensions (in.)

Number Number (in.) A B C D E F
70-103-HC 70LF-103-HC 1/2 NPT x 3/4 Hose 0.50 1.68 2.81 2.97 3.87 1.75
70-104-HC 70LF-104-HC 3/4 NPT x 3/4 Hose 0.68 1.96 3.50 3.67 4.87 2.12
70-105-HC 70LF-105-HC 1 NPT x 3/4 Hose 0.87 2.24 3.92 4.16 5.28 2.43
70-203-HC 70LF-203-HC 1/2 Solder x 3/4 Hose 0.50 1.68 3.14 3.28 3.89 1.75
70-204-HC 70LF-204-HC 3/4 Solder x 3/4 Hose 0.68 1.96 3.94 4.09 4.89 2.12
70-205-HC - 1 Solder x 3/4 Hose 0.87 2.24 4.49 4.73 5.28 2.43
19
BALL VALVES
70-300/400 SERIES BALL VALVE WITH FNPT x UNION END

This valve combines a pipe union with ball valve shut-off; it saves time and
labor by eliminating the need for extra connections. Viton O-ring sealed
union requires light torque for proper seal.
FEATURES NPT and solder union connection
ASTM B584 Bronze Vacuum service to 29 in. Hg
Blowout-proof stem design 70LF-300/400 Series features EZ-
Adjustable packing gland SolderTM Lead Free Bronze
Number Number (in.) A B C D E
NPT
70-301-01 1/4 0.37 1.90 2.93 1.75 3.87
70-302-01 3/8 0.37 1.90 2.93 1.75 3.87
70-303-01 70LF-303-01 1/2 0.50 2.01 3.14 1.81 3.87
70-304-01 70LF-304-01 3/4 0.68 2.46 3.96 2.12 4.87
70-305-01A 70LF-305-01A 1 0.87 2.84 4.52 2.25 4.87
70-306-01 70LF-306-01 1-1/4 1.00 2.68 4.68 2.62 5.50
70-307-01 70LF-307-01 1-1/2 1.25 2.87 5.06 3.05 8.00
70-308-01 70LF-308-01 2 1.50 3.25 5.59 3.24 8.00
Solder
70-403-01 1/2 0.50 2.00 3.43 1.75 3.87
70-404-01 70LF-404-01 3/4 0.68 2.62 4.56 2.06 4.78
70-405-01A 70LF-405-01A 1 0.87 2.87 5.66 2.25 4.78
70-406-01 70LF-406-01 1-1/4 1.00 2.87 5.18 2.62 5.50
70-407-01 70LF-407-01 1-1/2 1.25 2.92 5.53 3.10 8.00
70-408-01 70LF-408-01 2 1.50 3.50 6.75 3.24 8.00
70-600 SERIES THREADED 3-WAY DIVERTER BALL VALVE

Ideal for applications requiring flow diversion, this valve combines the
features of two valves. Its large ports make tank selection and fluid transfers
quicker and easier. Easy quarter-turn operation.
FEATURES
Simple quarter-turn operation
ASTM B584 Bronze
Blowout-proof stem
See 70-900 for solder version
Model Size Dimensions (in.)
Number (in.) A B C D E F G H I
70-601-01 1/4 0.37 1.12 2.32 1.80 3.88 1.18 0.875 1.37 10-24
70-602-01 3/8 0.37 1.12 2.32 1.80 3.88 1.18 0.875 1.37 10-24
70-603-01 1/2 0.50 1.09 2.25 1.75 3.87 1.18 0.87 1.37 10-24
70-604-01 3/4 0.68 1.50 3.00 2.12 4.87 1.62 0.87 1.37 10-24
70-605-01 1 0.81 1.59 3.18 2.25 4.87 1.71 0.87 1.37 10-24
70-606-01 1-1/4 1.00 1.97 3.95 2.69 5.50 2.01 0.93 1.50 1/4-20
70-607-01 1-1/2 1.25 2.21 4.40 2.87 5.50 2.38 0.94 1.50 1/4-20
70-608-01 2 1.50 2.34 4.69 3.00 5.50 2.50 0.94 1.50 1/4-20
20
BALL VALVES
70-800 SERIES MALE X FEMALE NPT BALL VALVE

Eliminates need for extra nipple when connecting to female connection to
save time and labor. Ruggedly built for lasting performance with chromium-
plated ball and blowout-proof stem.
FEATURES
600 psig CWP, non-shock Adjustable stem packing
150 SWP steam rating Vacuum service to 29 Hg
E
70-801-01 1/4 0.37 1.40 2.43 1.75 3.87
70-802-01 3/8 0.37 1.46 2.50 1.75 3.87
D
70-803-01 70LF-803-01 1/2 0.50 1.68 2.81 1.81 3.87
FNPT
70-804-01 70LF-804-01 3/4 0.68 2.00 3.50 2.12 4.87
OA
70-805-01 70LF-805-01 1 0.87 2.31 4.00 2.25 4.87
MNPT 70-806-01 70LF-806-01 1-1/4 1.00 2.31 4.31 2.62 5.50
B
70-807-01 70LF-807-01 1-1/2 1.25 3.00 5.18 3.06 8.00
C NOTE: 1/4, 3/8, and 1/2 are full port.
70-900 SERIES 3-WAY DIVERTER VALVE WITH SOLDER ENDS

Tank selection and fluid transfers are easier because of large port diameters.
The valve is 100 percent air tested under water. Designed to be soft soldered
without disassembly.
FEATURES
Simple quarter-turn operation
ASTM B584 Bronze
Blowout-proof stem
Adjustable packing
See 70-600 for NPT version
Made in USA

Number (in.) A B C D E F G H
70-903-01 1/2 0.50 1.44 2.87 1.75 3.87 1.34 0.628 0.50
70-904-01 3/4 0.68 1.94 3.87 2.12 4.87 1.69 0.878 0.90
70-905-01 1 0.81 2.19 4.42 2.25 4.87 1.87 1.129 0.90
21
BALL VALVES
32-100 SERIES REGULAR PORT THREADED END BRONZE BALL VALVE

NPT threaded ball valve rated to 400 psig CWP, non-shock and 125 psig for
saturated steam. Blowout-proof stem design with adjustable packing gland.
FEATURES
ASTM B584 Bronze
PTFE seats and MPTFE stuffing box ring
Made in USA
OPTIONS
Tee handle (-07)
Round handle (-15)
SS latch-lock lever & nut (-27)
Balancing stop (-92)
Number (in.) A B C D E
32-101-01 1/4 0.37 0.80 1.60 1.65 2.87
32-102-01 3/8 0.37 0.80 1.60 1.65 2.87
32-103-01 1/2 0.40 1.00 2.00 1.68 2.87
32-104-01 3/4 0.65 1.20 2.41 1.90 3.87
32-105-01 1 0.75 1.55 3.09 2.18 4.87
32-106-01 1-1/4 1.00 1.72 3.44 2.53 5.50
32-107-01 1-1/2 1.12 1.93 3.87 2.69 5.50
32-108-01 2 1.50 2.17 4.37 2.94 5.50
22
BALL VALVES
common ball valve options
Apollo offers these options on the 70 Series as well as many other valve series. Note: Not all
Suffix No. options are available on all sizes and models. Review the latest submittal sheet or contact the
factory to determine availability. Most available as a factory installed option or as a kit for field
-04 installation or retrofit.
2-1/4 STANDARD BALL VALVE WITH STEM EXTENSION

Stem Extension A plated steel stem extension to accommodate 2 thick pipe insulation or to relocate handle
position.
-07
TEE HANDLE
Plated steel tee handle is ideal when space is limited and where safety is a consideration.
Handle still provides visual indication of OPEN or CLOSED position.
-08
90 REVERSED STEM
Used in applications when handle is required to be in a parallel position when closed.
-10
STAINLESS STEEL LEVER AND NUT
Additional corrosion resistance for damp or marine installations.
-11 THERMA-SEAL HANDLE - NEW UL 2043 LISTING

The Therma-Seal thermal insulating tee-handle is designed to be use in applications where
vapor barrier piping insulation is required. Manufactured from high strength glass reinforced
nylon, these handles are ideally suited for the toughest commercial and industrial applications.
Handles are available as a factory installed option (-11 option suffix) or as a kit for retro fits. UL
2043 listed for plenum installations.
-16 or -58 CHAIN LEVER BALL VALVES

Reliable quarter turn operation in overhead applications. A favorite for use in industrial
environments.
Specify suffix -16 for assembly with valve in vertical position
Specify -58 for valve in horizontal position
-17
ROUGH CHROME PLATING
Use where a clean, bright finish is required or for matching up with other chrome-plated
equipment.
23
BALL VALVES
common ball valve options
Apollo offers these options on the 70 Series as well as many other valve series. Note: Not all
options are available on all sizes and models. Review the latest submittal sheet or contact the
Suffix No. factory to determine availability.
-27
STAINLESS STEEL LATCH LOCK - LOCKING LEVER HANDLE
Sliding lock mechanism secures handle in open or closed position. Valve can also be padlocked
open or closed.
-30 CAM-LOCK HANDLE

Patented Cam-Lock handle gives valve extra protection against accidental operation. Reliable
quarter-turn shut-off from a versatile, ruggedly built valve.
Available for the following Series: 70, 71, 73A, 76, 82, 83, 86, 87, 89, 9A, 92, and 96
-32 and -83

STAINLESS STEEL TEE HANDLE AND NUT
Increased corrosion resistance versus the plated steel -07 option.
-32 for standard bronze
-83 for 77B/77BLF and 77C/77CLF Series
-41 BALL VALVE WITH AUTOMATIC DRAIN

When this valve is closed for maintenance of pneumatic tool, downstream pressure from valve
to tool is automatically drained to atmosphere to prevent accidental operation of the tool,
causing possible injury.
Conforms to certain OSHA requirements in pneumatic installations
Easy, safe maintenance of pneumatic tools
Cannot be used where drained media could cause damage
Temperature range: 50F to 200F
Rated 125 psig CWP, non-shock air or water
Includes directional arrow for correct installation
Available with latch lock option, specify -27 -41 suffix
-48 Available for the following Series: 70, 71, 75, and 78
STAINLESS STEEL OVAL HANDLE

Available for the following Series: 70, 71, 73A, 76, 76F, 77, 82, 83, 85, 86, 89, 9A, 92 and 96
Resistant to accidental operation
-94
BALL VALVE WITH BALANCING STOP AND STEM EXTENSION
Ideal for HVAC systems. Stop plate and a 2-1/4 stem extension combination to accommodate
insulation and handle repositioning. Contact customer service for exact handle dimensions
24
BALL VALVES
heavy duty valves
71-100 SERIES BALL VALVE WITH MOUNTING PAD

Designed to easily accommodate spring return handle, actuator or simple
panel mounting. Threaded end connections with RPTFE seats and stuffing
box ring.
FEATURES
3/4 to 3 models (See 77 Series for 1/4 - 1/2)
600 CWP non-shock
Blowout-proof stem
ASTM B584 Bronze
Round handle option
G G Adjustable packing
F F

G G Number (in.) A B C D E F G H
71-104-01 3/4 0.68 1.50 3.00 2.12 4.87 0.87 1.37 10-24 NC
SIZES 3/4" - SIZES
2" 3/4" H
- 2" H
E E 71-105-01 1 0.87 1.68 3.37 2.25 4.87 0.87 1.37 10-24 NC

SIZE 3" SIZE 3"
71-106-01 1-1/4 1.00 2.00 4.00 2.62 5.50 0.93 1.50 1/4-20 NC
F F
71-107-01 1-1/2 1.25 2.18 4.37 2.87 8.00 0.93 1.50 1/4-20 NC
D
H H
71-108-01 2 1.50 2.34 4.68 3.06 8.00 0.93 1.50 1/4-20 NC

OA OA
NPT BOTH ENDS

NPT BOTH ENDS 71-100-01 3 2.50 3.37 6.75 4.12 8.00 3.37 2.75 1/4-20 NC
B B
C C
71-500 SERIES CAST BRONZE VALVE WITH SPRING RETURN HANDLE

Ideal in applications where the valve must be in OFF position at all times such
as feeding fuel lines. Can be used in reverse with 90 reverse stem option.
Basic configuration: spring return to CLOSED. All lever components are
stainless steel.
FEATURES
Spring return to OPEN (-08)

Number (in.) A B C D
71-501-01 1/4 0.43 1.12 2.25 7.00
71-502-01 3/8 0.50 1.12 2.25 7.00
71-503-01 1/2 0.50 1.12 2.25 7.00
71-504-01 3/4 0.68 1.50 3.00 7.00
71-505-01 1 0.87 1.68 3.37 7.00
71-506-01 1-1/4 1.00 2.00 4.00 9.00
71-507-01 1-1/2 1.25 2.18 4.37 9.00
71-508-01 2 1.50 2.34 4.68 9.00
25
BALL VALVES
heavy duty valves
73A-100 SERIES FORGED CARBON STEEL BALL VALVE

Threaded, 2 piece design, 1/4 to 1 2000 psig CWP, 1-1/4 to 2 1500 psig CWP
Cold Non-Shock. 150 psig Saturated Steam.
FEATURES
RPTFE seats & packing
Forged construction
Raised handle stops
Blow-out-proof stem design
Zinc phosphate corrosion protection
(-24) Fire safe to API 607 4th ed. class 600 burn
AAR Approved #E999032
Vacuum Service to 29 inches Hg.

73A-101-01A 1/4 .37 1.02 2.30 1.72 3.85
E
73A-102-01A 3/8 .37 1.08 2.37 1.72 3.85
73A-103-01A 1/2 .50 1.18 2.31 1.78 3.85
73A-104-01A 3/4 .68 1.57 3.07 2.07 4.75
73A-105-01A
D
1 .87 1.73 3.40 2.18 4.75
73A-106-01 1-1/4 1.00 1.98 3.97 2.72 5.50
A
73A-107-01 1-1/2 1.25 2.14 4.32 3.12 7.75
73A-108-01 2 1.50 2.73 5.44 3.27 7.75
B
C
76F-100-A SERIES STAINLESS STEEL FULL PORT BALL VALVE

Threaded, 2 piece design, 1/2-2 1000 psig CWP Cold Non-Shock, 150 psig.
Saturated Steam, Vacuum Service to 29 inches Hg.
FEATURES
316 SS Investment cast components
RPTFE seats
Two-piece body
Blow-out-proof stem design
(-24) Certified to API 607, 6th Edition, Class 600 burn
Meets NACE MR-01-75-2000
SS lever and nut
Available with SS latch lock lever (-27)
D Therma Seal tee handle option (-11)
Standard valve is certified Lead Free
NSF/ANSI-61-G, NSF/ANSI 372 Lead Free
F

Wt.
Number (in.) A B C D E F
E 76F-101-01A 1/2
76F-104-01A 3/8
A 76F-103-01A 1/2 .50 1.21 2.35 1.27 1.73 3.85 0.57
76F-104-01A 3/4 .75 1.39 2.77 1.62 1.96 3.85 0.91
76F-105-01A 1 1.00 1.67 3.34 2.00 2.27 4.75 1.38
B
C
76F-106-01A 1-1/4 1.25 1.96 3.92 2.73 3.21 7.77 4.17
76F-107-01A 1-1/2 1.50 2.05 4.10 2.92 3.31 7.77 4.69
76F-108-01A 2 2.00 2.37 4.74 3.75 3.69 7.77 6.90
26
BALL VALVES
heavy duty valves
75-100-41 SERIES PADLOCKING BALL VALVE WITH AUTOMATIC DRAIN

Meets OSHA standards and provides for easy, safe maintenance of pneumatic
tools. Valve drains downstream pressure for safety when lever is closed. Valve
can be padlocked OPEN or CLOSED with same hardware.
FEATURES
ASTM B584 Bronze
Pad lock lever
Rated to 600 psi CWP - 150 SWP
Temperature range: 50F to 200F
Valve without drain option (suffix -01)
75-101-41 1/4 0.43 1.12 2.25 1.81 3.00
75-102-41 3/8 0.50 1.12 2.25 1.81 3.00
75-103-41 1/2 0.50 1.12 2.25 1.81 3.00
75-104-41 3/4 0.87 1.68 3.37 2.25 3.87
75-105-41 1 0.87 1.68 3.37 2.25 3.87
75-106-41 1-1/4 1.00 2.00 4.00 2.62 5.50
75-107-41 1-1/2 1.25 2.16 4.37 2.87 5.50
75-108-41 2 1.50 2.34 4.68 3.06 5.50
77-100 SERIES HEAVY DUTY FULL PORT NPT PANEL MOUNT BALL VALVE
Designed for easy actuator mounting or panel mounting where highest Cv
values are desired. RPTFE seats and stuffing box ring. Also available with 250
lb. steam trim option.
FEATURES 77 OPTIONS INCLUDE:
Mounting pad 2-1/4 Stem Extension Latch
ASTM B584 Bronze Lock Lever (-27)
Blowout-proof stem design Balance stop (-92)
Full flow, minimum pressure drop
F
TAPPING
1/4" - 3/4": #10-24 UNC
1" & 1-1/4": 1/4"-20 UNC
G
600 CWP, non-shock pressure rating
G Chain lever kits available 3/4- 2-1/2 (-16, -58)
SIZES 1/4" - 1-1/4"

Number (in.)
E
A B C D E F G Cv*
SIZES 1-1/2" - 2-1/2"
F
77-101-01 1/4 0.43 1.12 2.25 1.81 3.87 0.50 1.12 8.1
77-102-01 3/8 0.50 1.12 2.25 1.81 3.87 0.50 1.12 15
D
1-1/2" & 2": 5/16"-24 UNF

2-1/2": 1/4"-20 UNC
OA 77-103-01 1/2 0.50 1.12 2.25 1.81 3.87 0.50 1.12 15

77-104-01 3/4 0.81 1.56 3.12 2.12 4.87 0.87 1.37 51
B
C 77-105-01 1 1.00 1.81 3.62 2.62 5.50 0.93 1.50 68
Actuation assistance available on page 62, 77-106-01 1-1/4 1.25 2.12 4.25 2.87 5.50 0.93 1.50 125
with the Apollo Actuator Wizard located at 77-107-01 1-1/2 1.50 2.37 4.75 3.34 8.00 2.08 3.06 177
actuatorwizard.conbraco.com or by calling 77-108-01 2 2.00 2.65 5.37 3.71 8.00 2.41 3.52 389
customer support at (704)841-6000. 77-109-01 2-1/2 2.50 3.25 6.50 4.12 8.00 2.75 3.37 503
* The Cv factor is the gallons of water per minute that the valve will pass with 1 psig
pressure drop.
27
BALL VALVES
heavy duty valves
77-200 SERIES HEAVY DUTY FULL PORT SOLDER END BALL VALVE
Designed to be soldered into lines without disassembly. This allows a factory
tested valve to be installed without disturbing the seats and seals. Designed
for soft solder with melt points less than 500F.
FEATURES
Heavy duty cast bronze body
Chromium plated ball
Full flow, minimum pressure drop
600 CWP, non-shock pressure rating
150 SWP
77-204-01 3/4 0.81 2.12 4.12 2.12 4.87 0.88 0.75
77-205-01 1 1.00 2.33 4.60 2.62 5.50 1.13 0.90
77-206-01 1-1/4 1.25 2.60 5.15 2.87 5.50 1.38 0.96
77-207-01 1-1/2 1.50 3.00 6.00 3.34 8.00 1.63 1.09
77-208-01 2 2.00 3.62 7.24 3.71 8.00 2.13 1.34
77-209-01 2-1/2 2.50 3.93 7.87 4.12 8.00 2.63 1.48
77-900 SERIES FULL PORT SAE STRAIGHT-THREAD BALL VALVES

Valve connections are designed for extended leak-free and energy saving
performance in a broad range of applications, especially in manufacturing
environments.
FEATURES
Mounting pad for easy actuation Blowout-proof stem and lever
600 CWP non-shock handle standard
150 SWP Adjustable packing gland
ASTM B584 Bronze Full port
SAE J1926-1 (ISO 11926-1) Straight thread w/o-ring boss
connections connection
E
TAPPING
1/4" - 3/4": #10-24 UNC
RPTFE seats & packing
1" & 1-1/4": 1/4"-20 UNC
D
F Model Nom. Tube Size Dimensions (in.)
Number O.D. (in.) (in.) A B C D E F G
OA
77-901-01 1/4 7/16-20 0.43 1.12 2.25 1.81 3.87 0.50 1.12
G
77-902-01 3/8 9/16-18 0.50 1.12 2.25 1.81 3.87 0.50 1.12
B
SIZES 1/4" - 1-1/4"
77-903-01 1/2 3/4-16 0.50 1.12 2.25 1.81 3.87 0.50 1.12
C
G F
77-904-01 3/4 11/16-12 0.81 1.56 3.12 2.12 4.87 0.87 1.37
77-905-01 1 15/16-12 1.00 1.81 3.62 2.62 5.50 0.93 1.50
5/16"-24 UNF 77-906-01 1-1/4 1-5/8-12 1.25 2.12 4.25 2.87 5.50 0.93 1.50
77-907-01 1-1/2 1-7/8-12 1.50 2.37 4.75 3.34 8.00 2.08 3.06
77-908-01 2 2-1/2-12 2.00 2.65 5.37 3.71 8.00 2.41 3.52
SIZES 1-1/2" - 2"
Actuation assistance available on page 62, with the Apollo Actuator Wizard located
at actuatorwizard.conbraco.com or by calling customer support at (704)841-6000.
28
BALL VALVES
specialty valves
77D SERIES FULL PORT BRONZE BALL VALVE WITH DIRECT ISOMOUNTING PAD
Apollos solid stainless steel ball design in a bronze valve with an integral ISO
5211 mounting pad with 100% American construction
FEATURES
600 CWP pressure rating
Multi-fill seats and stem bearing
High cycle dual o-ring stem seal design (EPDM is standard). Most liquids
and gases compatible with the o-ring seals
Ball is slot vented to equalize cavity and
line pressure
MSS SP-110 compliant
G
Direct mount actuator ready
F
Suffix Material Temp Range Steam (max)
-01E (std) EPDM -20 to 400F 150 SWP @ 366F
E
D
-01N Nitrile -20 to 250F 15 SWP @ 250F

OA
-01V Viton -20 to 400F 50 SWP @ 297F
G1 (4X)
F1 (4X)
H
C
Number (in.) A B C D E F 0F1 G 0G1 H
77D-143-01E 1/2 0.50 1.15 2.25 1.00 1.37 0.997 0.224 1.167 0.281 0.275
Actuation assistance available on page 62,
77D-144-01E 3/4 0.75 1.33 2.65 1.38 1.79 1.167 0.281 1.392 0.281 0.275
with the Apollo Actuator Wizard located at
actuatorwizard.conbraco.com or by calling
77D-145-01E 1 1.00 1.54 3.07 1.67 2.20 1.167 0.281 1.392 0.281 0.430
customer support at (704)841-6000. 77D-147-01E 1-1/2 1.50 2.12 4.23 2.31 3.05 N/A N/A 1.949 0.344 0.551
77D-148-01E 2 2.00 2.43 4.85 2.68 3.43 N/A N/A 1.949 0.344 0.551
7K-100 SERIES FULL PORT SAFETY EXHAUST VALVE WITH 1/4 NPT TAP FOR DRAIN
For use on pneumatic equipment. Furnished with a 1/4 NPT tapped drain to
accommodate a muffler or to pipe the exhausted air to a safe location.
FEATURES
Safely vents compressed air (or other non-hazardous gases) from piping
downstream of the closed valve
Sizes 1/4 - 2-1/2
FNPT threads
Rated 125 psig-air or water, CWP, non-shock
Temperature range: +50F - +200F
Optional stainless steel latch lock handle that locks in closed position
only, specify suffix (-46)
Number (in.) A B C D E F G H I J K
7K-101-01 1/4 0.37 1.03 2.06 1.75 3.87 N/A N/A 0.09 0.53 1.18 N/A
7K-102-01 3/8 0.37 1.03 2.06 1.75 3.87 N/A N/A 0.09 0.53 1.18 N/A
7K-103-01 1/2 0.50 1.10 2.19 1.75 3.87 N/A N/A 0.12 0.59 1.25 N/A
7K-104-01 3/4 0.81 1.56 3.12 2.12 4.78 0.87 1.37 0.29 0.90 1.56 0.90
7K-105-01 1 1.00 1.80 3.61 2.62 5.50 0.93 1.50 0.31 1.12 1.78 1.12
7K-106-01 1-1/4 1.25 2.12 4.25 2.87 5.50 0.93 1.50 0.37 1.37 2.03 1.37
7K-107-01 1-1/2 1.50 2.37 4.74 3.30 7.78 2.08 3.06 0.50 1.56 2.21 1.28
7K-108-01 2 2.00 2.70 5.38 3.71 7.78 2.41 3.52 0.62 2.03 2.68 1.56
7K-109-01 2-1/2 2.50 3.25 6.50 4.05 7.78 2.75 3.37 1.09 2.34 3.00 2.00
Also available in 70 & 77 Series as - 41 option (without tapped drain)
29
BALL VALVES
specialty valves
7K-SV SERIES SECURE-VENT FEATURE (-SV)

Available on the Apollo 77 and 7K full port bronze ball valves. Safely vents
compressed air (or other non-hazardous gases) from piping downstream of
the closed valve.
FEATURES
Reliable shut-off and venting
Pressure rating: 200 psig CWP, non-shock
Temp. range: -20F to 200F
Economical no leakage operation
Belleville spring live-loaded active upstream seating
(7K-SV Series Shown) Available with a full complement of handles

7K-101-SV 1/4 0.43 1.43 2.52 1.76 3.88 0.50 1.12
7K-102-SV 3/8 0.50 1.60 2.69 1.76 3.88 0.50 1.12
7K-103-SV 1/2 0.50 1.50 2.59 1.76 3.88 0.50 1.12
7K-104-SV 3/4 0.81 1.82 3.37 2.16 5.43 0.87 1.37
7K-105-SV 1 1.00 2.05 3.86 2.69 5.43 0.93 1.50
7K-106-SV 11/4 1.25 2.37 4.50 2.91 5.43 0.93 1.50
7K-107-SV 11/2 1.50 2.37 7.78 3.31 7.78 2.08 3.06
7K-108-SV 2 2.00 3.00 5.69 3.73 7.78 2.40 3.52
78-260/290 SERIES BRASS AND BRONZE INSTRUMENTATION BALL VALVES AND BACKFLOW TEST COCKS
Male x Female threaded. 400 psig CWP, non-shock. Air and liquid service.
FEATURES
Micro-finish ball
PTFE seats
Nitrile stem seal
78LF-290: Bronze 78-261: Brass Plated steel tee handle
Bronze Valves - Tee Compact design
Optional mixed end fittings available
BRASS INSTRUMENTATION BALL VALVE - TEE HANDLE
Number (in.) A B C D E Cv* Wt.
78-261-05 1/4M x 1/4F 0.31 0.43 1.43 0.87 1.25 5.50 0.19
BRONZE INSTRUMENTATION BALL VALVE (INTERNATIONAL) - SCREW SLOT - LEAD FREE

Bronze Valves - Slot Number (in.) A B C D E Cv* Wt.
78LF-290-01 1/8M x 1/4F 0.21 0.80 1.60 0.72 N/A 4.00 0.19
78LF-291-01 1/4M x 1/4F 0.31 0.80 1.60 0.72 N/A 5.50 0.19
78LF-292-01 1/8 x 1/4 SAE 0.21 0.80 1.60 0.72 N/A 4.00 0.19
78LF-293-01 1/4 x 1/4 SAE 0.31 0.80 1.60 0.72 N/A 5.50 0.19
* The Cv factor is the gallons of water per minute that the valve will pass with a 1 psig
pressure drop.
* Also see 94MBV Instrumentation Ball Valve
30
BALL VALVES
specialty valves
78-130 SERIES FEMALE END IRRIGATION VALVE FOR UNDERGROUND SERVICE

Ideal for underground or below grade applications. This series (3/8-2 FNPT)
features a square head nut welded to the stem to allow operations with a
ground key from standard grade.

Number (in.) A B C D E F
78-132-01 3/8 0.37 1.03 2.06 1.75 0.62 0.50
78-133-01 1/2 0.50 1.09 2.18 1.83 0.62 0.50
78-134-01 3/4 0.68 1.50 3.00 2.12 0.62 0.62
78-135-01 1 0.87 1.68 3.37 2.25 0.62 0.62
78-136-01 1 1/4 1.00 2.00 4.00 2.88 0.75 0.75
78-137-01 1 1/2 1.25 2.18 4.38 3.06 0.75 0.75
78-138-01 2 1.50 2.34 4.68 3.25 0.75 0.75
OPTIONS
-41 Auto-drain (directional)
78-620 SERIES BRONZE NPT IRRIGATION VALVE WITH AUTO-DRAIN

Ideal for underground use or where drained media will not cause damage.
Heavy pattern design features ASTM B584 Bronze body.
FEATURES
Auto-drain feature (when valve is in closed position) is standard
RPTFE seats and seals
Stainless steel cover
200 psig water, CWP, non-shock
Temperature range +50F to 200F

78-621-01 3/4 0.68 1.47 2.96 2.40 1.81
78-622-01 1 0.87 1.66 3.34 2.53 1.81
78-623-01 1-1/4 1.00 1.98 3.97 3.00 2.50
78-624-01 1-1/2 1.25 2.12 4.28 3.18 2.50
78-625-01 2 1.50 2.35 4.67 3.37 2.50
31
BALL VALVES
heavy duty valves
78-660 & 962 SERIES BRONZE PURGE & DRAIN BALL VALVE WITH CENTER DRAIN
Center tap drain allows for winterization or purge and drain function. Features
bronze body with built-in mounting pad for panel mounting or actuation.
Ideal for hydronic heating and marine applications.
FEATURES
1/8 NPT side tap and plug
Stainless steel lever and nut
Blowout-proof stem
E
Adjustable packing
H
DRAIN
Drainable ball cavity to prevent freezing
#10-24 UNC
D Actuation assistance available on page 62, with the Apollo Actuator Wizard located
at actuatorwizard.conbraco.com or by calling customer support at (704)841-6000.
OA
G
E Number (in.) A B C D E F G H
B H F 78-664-01
#10 SCREW
3/4 0.68 1.50 3.00 2.12 4.87 0.87 1.37 0.17
C DRAIN #10-24 UNC 78-665-01 1 0.87 1.68 3.37 2.25 4.87 0.87 1.37 0.21
D
78-666-01 1-1/4 1.00 2.00 4.00 2.62 5.50 0.93 1.50 0.28
78-667-01 1-1/2 1.25 2.18 4.37 3.05 8.00 0.93 1.50 0.40
OA
78-962-01 2 1.50 2.34 4.68 3.24 8.00 0.93 1.50 0.45
G
B #10 SCREW
F
79-700 SERIES UL-LISTED REFRIGERANT BALL VALVE ASSEMBLY

Complete hermetically welded assembly includes copper extensions and forged
brass refrigerant ball valve with capped, triple-sealed stem to minimize leaks.
FEATURES
Chrome plated ball
Full port through 2-5/8
Bi-directional flow design
Sizes from 3/8 to 3-1/8 O.D. tube
All sizes UL listed - SFJQ
For use with refrigerant Group 2 fluids
Number (in.) A B C D E F Cv*
79-701-01 3/8 3.38 6.45 0.45 1.56 0.38 0.38 8.5
79-702-01 1/2 3.38 6.45 0.45 1.56 0.38 0.50 8.5
79-703-01 5/8 3.56 6.82 0.50 1.56 0.50 0.62 9.8
79-704-01 7/8 3.91 7.53 0.68 1.79 0.75 0.87 32.0
79-705-01 1-1/8 4.39 8.51 0.87 1.98 0.90 1.12 44.0
79-706-01 1-3/8 4.42 8.94 1.25 2.62 0.96 1.38 66.0
79-707-01 1-5/8 4.55 9.19 1.25 2.62 1.09 1.62 148.0
79-708-01 2-1/8 5.16 10.31 1.50 2.93 1.34 2.12 218.0
79-709-01 2-5/8 6.50 13.00 2.50 3.90 1.48 2.62 440.0
79-600-01 3-1/8 7.00 14.00 2.50 3.90 1.67 3.12 390.0
* The Cv factor is the gallons of water per minute that the valve will pass with 1 psig
pressure drop.
32
BALL VALVES
uni-body general purpose valves &
three-piece full port valves
9A-100 SERIES HEAVY PATTERN UNI-BODY THREADED BALL VALVE

One piece bronze valve eliminates leak paths. Features static grounding
devices and adjustable packing gland. Lever handle standard.
FEATURES
150 SWP
OPTIONS INCLUDE:
Cam lock option (-30 suffix)
Round handle option (-15 suffix)
Latch lock handle option (-27 suffix)
9A-101-01 1/4 0.37 1.34 2.59 1.68 3.87
9A-102-01 3/8 0.37 1.34 2.59 1.68 3.87
9A-103-01 1/2 0.37 1.34 2.59 1.81 3.87
9A-104-01 3/4 0.50 1.44 2.84 1.84 3.87
9A-105-01 1 0.62 1.72 3.28 2.00 4.87
9A-106-01 1-1/4 0.81 1.94 3.84 2.18 4.87
9A-107-01 1-1/2 1.00 2.06 4.00 2.68 5.50
9A-108-01 2 1.25 2.29 4.56 2.87 5.50
Three-Piece Full Port Valves

82-100 SERIES FULL PORT BRONZE NPT THREE-PIECE VALVE
This inline-repairable threaded ball valve offers RPTFE seats and seals and a
600 CWP, non-shock rating.
FEATURES
ASTM B584 Bronze body and ends
SAE Grade 8 body bolts
Adjustable packing nut
Full port flow
600 CWP, 150 SWP (3-4 400 CWP, 150 SWP)
Numerous options available
82-14X with SS ball and stem option
Lead Free option (82LF)
- NSF/ANSI 61-G and NSF/ANSI 372 Lead Free
- Easily Identifiable White Handle Grip and Blue Lead Free Hang Tag

82-101-01 82LF-101-01 1/4 0.43 1.28 2.56 1.81 3.87
82-102-01 82LF-102-01 3/8 0.50 1.28 2.56 1.81 3.87
82-103-01 82LF-103-01 1/2 0.62 1.40 2.81 1.93 4.87
82-104-01 82LF-104-01 3/4 0.81 1.71 3.43 2.18 4.87
82-105-01 82LF-105-01 1 1.00 1.93 3.87 2.62 5.50
82-106-01 82LF-106-01 1-1/4 1.25 2.37 4.75 2.87 5.50
82-107-01 82LF-107-01 1-1/2 1.50 2.62 5.25 3.37 8.00
82-108-01 82LF-108-01 2 2.00 3.01 6.03 3.68 8.00
82-109-01 82LF-109-01 2-1/2 2.50 3.62 7.25 5.14 9.75
82A-140-01 - 3 3.00 4.18 8.37 8.10 19.13
82A-14A-01 - 4 4.00 5.43 10.86 8.88 19.13
33
BALL VALVES
three-piece full port valves
82-200 SERIES FULL PORT BRONZE THREE-PIECE SOLDER/BRAZED END VALVE

Valve features full port and is easily repaired inline. Designed for soft soldering
or brazed* installation. Includes RPTFE seats and seals.
FEATURES
ASTM B584 Bronze
SAE Grade 8 body bolts
600 CWP, non-shock
82-24X with SS ball and stem option
Lead Free option (82LF) featuring EZ-SolderTM Lead Free Bronze
- NSF/ANSI 61-G and NSF/ANSI 372 Lead Free
- Easily Identifiable White Handle Grip and Blue Lead Free Hang Tag
Number Number (in.) A B C D E F G
82-202-01 82LF-202-01 3/8 0.50 1.28 2.56 1.81 3.87 0.50 0.37
82-203-01 82LF-203-01 1/2 0.62 1.40 2.81 1.93 4.87 0.63 0.50
82-204-01 82LF-204-01 3/4 0.81 1.71 3.43 2.18 4.87 0.88 0.75
82-205-01 82LF-205-01 1 1.00 1.93 3.87 2.62 5.50 1.13 0.90
82-206-01 82LF-206-01 1-1/4 1.25 2.37 4.75 2.87 5.50 1.38 0.96
82-207-01 82LF-207-01 1-1/2 1.50 2.60 5.25 3.37 8.00 1.63 1.09
82-208-01 82LF-208-01 2 2.00 3.01 6.03 3.68 8.00 2.13 1.34
82-209-01 82LF-209-01 2-1/2 2.50 3.62 7.25 5.14 9.38 2.63 1.47
82A-240-01 - 3 3.00 4.18 8.37 8.10 19.13 3.13 1.66
82A-24A-01 - 4 4.00 5.43 10.86 8.88 19.13 4.13 2.16
* Model 82LF suitable for soft soldering only.
82-200/82-240 SERIES THREE-PIECE FULL PORT VALVE WITH BRAZED TUBE EXTENSIONS
This valve is useful in pharmaceutical, medical gas, pneumatic, and liquid
applications where valves should not be disassembled prior to soldering
or brazing.
FEATURES
6 type K copper tubing brazed into both end cups
F Optional gage port tapping
Oxygen service option
C ( TYPE "K"
COPPER TUBING)
SILVER BRAZED, TYP.
Complies with NFPA99 and CGA G4.1 (oxygen cleaned models)
E
B
ASTM B584 Bronze

A
SS ball and stem option

G
Size Standard Model Standard Oxygen Cleaned Oxygen Cleaned Dimensions (in.)
No. Model No. Model No. Model No.
(in.) 316 Ball & Stem 316 Ball & Stem A B C D E F G
3/8 1/2 0.50 0.049 13.54 1.76 3.88 6.00
1/2 82-203-B8 82-243-A8 82-203-K1 82-243-K1 5/8 0.62 0.049 13.81 2.00 4.87 6.00
3/4 82-204-A8 82-244-B3 82-204-K1 82-244-K1 7/8 0.81 0.065 13.93 2.18 4.87 6.00
1 82-205-B7 82-245-B1 82-205-K1 82-245-K1 1-1/8 1.00 0.065 14.04 2.62 5.50 6.00
1-1/4 82-206-B7 82-246-B0 82-206-K1 82-246-K1 1-3/8 1.25 0.065 14.75 2.89 5.50 6.00
1-1/2 82-207-B2 82-247-B2 82-207-K1 82-247-K1 1-5/8 1.50 0.072 15.07 3.37 8.00 6.00
2 82-208-B7 82-248-B2 82-208-K1 82-248-K1 2-1/8 2.00 0.083 15.23 3.70 8.00 6.00
2-1/2 82-209-A2 82-249-A2 82-209-K1 82-249-K1 2-5/8 2.50 0.095 23.51 5.14 9.38 9.60
3 - 82A-240-A2 - 82A-240-K1 3-1/8 3.00 0.109 24.00 6.77 18.00 9.40
4 - 82A-24A-A0 - 82A-24A-K1 4-1/8 4.00 0.134 25.50 8.26 18.00 9.41
34
BALL VALVES
medical gas ball valves
DESIGN: F1, F3, & G3 CONFIGURATIONS

Cast bronze valve body & valve end caps Cleaned and bagged for oxygen service per CGA G4.1 &
RPTFE seats and stuffing box ring NFPA 99
600 psig CWP non-shock (3 & 4 400 CWP) Factory brazed, male extensions for solder or brazed
Vacuum Service to 29 inches Hg installation without disassembly (Type K copper tubing
Full port in all sizes brazed into both end caps)
Blow-out-proof stem design Single or double gauge ports
Adjustable packing nut Optional 316 stainless steel ball & stem
In-line repairable Made in USA
Locking handle
OUTSIDE THE ZONE BOX
NFPA 99 requires the valves to be secured in the open position. For medical gas applications that are Outside-the-Zone-Box,
Apollo offers three standard configurations: F1 (1 gage port), F3 (2 gage ports), and G3 (no gage ports).
82-200-F1 AND 82-240-F1 SERIES MALE EXTENSIONS AND 1 GAUGE PORT
82-240 Model Dimensions (in.)

Size 82-200 Model Number
(in.) Number 316SS
Ball & Stem A B C D E F G H
1/2 82-203-F1 82-243-F1 0.62 6.91 17.41 2.23 5.31 0.049 0.625 7.15
3/4 82-204-F1 82-244-F1 0.81 6.97 17.47 2.41 5.31 0.065 0.75 7.22
1 82-205-F1 82-245-F1 1.00 7.03 17.62 3.01 6.29 0.065 1.25 7.28
1-1/4 82-206-F1 82-246-F1 1.25 7.38 22.71 3.22 6.29 0.065 1.375 7.00
1-1/2 82-207-F1 82-247-F1 1.50 7.50 22.57 4.04 8.93 0.072 1.625 6.74
2 82-208-F1 82-248-F1 2.00 7.74 22.58 4.15 8.93 0.083 2.125 6.51
2-1/2 82-209-F1 82-249-F1 2.50 11.75 23.50 5.31 10.06 0.095 2.50 6.38
3 - 82A-240-F1 3.00 11.94 23.87 8.10 18.00* 0.0450 3.00 7.75
4 - 82A-24A-F1 4.00 12.68 25.37 8.88 18.00* 0.0700 4.00 8.00
82-200-F3 AND 82-240-F3 SERIES MALE EXTENSIONS AND 2 GAUGE PORTS
82-240 Model Dimensions (in.)

Size 82-200 Model Number
(in.) Number 316SS A B C D E F G H
Ball & Stem
1/2 82-203-F3 82-243-F3 0.62 12.27 24.53 2.23 5.31 0.049 0.625 4.25
3/4 82-204-F3 82-244-F3 0.81 12.25 24.50 2.41 5.31 0.065 0.75 4.24
1 82-205-F3 82-245-F3 1.00 12.30 24.60 3.01 6.29 0.065 1.25 4.24
1-1/4 82-206-F3 82-246-F3 1.25 12.23 24.46 3.22 6.29 0.065 1.375 4.23
1-1/2 82-207-F3 82-247-F3 1.50 12.25 24.50 4.04 8.93 0.072 1.625 4.25
2 82-208-F3 82-248-F3 2.00 12.25 24.50 4.15 8.93 0.083 2.125 4.25
2-1/2 82-209-F3 82-249-F3 2.50 11.75 23.50 5.31 10.06 0.095 2.50 6.38
3 - 82A-240-F3 3.00 11.94 23.87 8.10 18* .0450 3.00 7.75
4 - 82A-24A-F3 4.00 12.68 25.37 8.88 18* .0700 4.00 8.00
35
BALL VALVES
apollo international cast iron ball valves &
gas/fuel shut-off valves
6PLF SERIES CAST IRON CLASS 125 FLANGED BALL VALVE - LEAD FREE
The cast iron/epoxy coated, Class 125 Apollo InternationalTM 6PLF Series
Lead Free* Ball Valves offer unobstructed turbulence-free flow that gate and
butterfly valves cant match. Compact design and low profile handle for easy
C installation in tight areas.
FEATURES
A126 Class B Cast lron Body with Gear operators 8-10
FDA food-grade epoxy powder coat NSF/ANSI 61-G Water Quality
Stainless steel ball & stem NSF/ANSI 372 Lead Free
D ANSI B16.10 Face to Face dimensions
PTFE Seats
200 CWP/125 SWP allow direct replacement of comparable
ISO 5211 mounting pad for easy gate valves
B actuation Actuation assistance available on page 62,
Adjustable stem packing with the Apollo Actuator Wizard located at
Full port through 6 actuatorwizard.conbraco.com or by calling
A Vacuum service to 29 customer support at (704)841-6000.
Lever handles 2-6
LF Model Size Dimensions (in.)

Wt.
Number (in.) A B C D Valve Actuation Description
6PLF-208-01 2 7.00 6.00 12.20 6.50 22.70 Size Kit
6PLF-209-01 2-1/2 7.50 7.00 13.78 7.42 36.73 2 78253001 KIT, MTG, 6PLF208 TO A0150
6PLF-200-01 3 8.00 7.50 13.78 8.17 46.63 2-1/2 78253101 KIT, MTG, 6PLF209 TO A0150
6PLF-20A-01 4 9.00 9.00 15.75 9.00 71.83 3 78253201 KIT, MTG, 6PLF200 TO A0150
6PLF-20C-01 6 10.50 11.00 30.00 11.32 111.99 4 78253301 KIT, MTG, 6PLF20A TO A0350/0600
6PLF-20E-01* 8 11.50 13.50 30.00 11.32 210.54 6 78253401 KIT, MTG, 6PLF20C TO A0950
6PLF-20G-01* 10 13.00 16.00 33.00 13.05 294.10 8 - 10 78253501 KIT, MTG, 6PLF20E/20G TO A01600/A2500
* Gear Operated
Gas/Fuel Shut-Off Valves

94 MBV SERIES MINI BALL VALVE GAS RATED APOLLO INTERNATIONALTM
Designed for commercial and light industrial use. Full port, constructed of
heavy-duty forged brass, PTFE seats and gland follower with double viton
o-rings, to prevent stem leakage.
FEATURES
Reversible handle
Blowout-proof stem
Double Viton o-ring stem seals
Large raised wrench flats
Chrome plated brass ball
MxF
Ideal for use as a gas cock or gauge cock
Maximum 600 psig at 100F, non-shock
FxF Temps from -40F to 300F
ANSI Z21.15-2009 / CSA 9.1-2009 (1/2 psi) Manually Operated Gas Valves
for Appliances.
ASME B16.44-2002 Manually Operated Metallic Gas Valves for use in
Above Ground Piping Systems (2 and 5 psig).
MSS-SP110 compliant
Model Size Dimensions (in.) Port Wt.
Number (in.) A B C (DIa.) (lbs.)
94-MBV-01 1/4 FNPT x 1/8 MNPT 1.95 1.09 1.71 0.31 0.19
94-MBV-02 1/4 FNPT x 1/4 MNPT 1.95 1.09 1.71 0.31 0.20
94-MBV-03 1/4 FNPT x 1/4 FNPT 1.68 1.09 1.71 0.31 0.17
94-MBV-04 1/8 FNPT x 1/8 MNPT 1.95 1.09 1.71 0.31 0.16
94-MBV-05 1/8 FNPT x 1/8 FNPT 1.68 1.09 1.71 0.31 0.16
36
BALL VALVES
80-100 SERIES UL LISTED GAS BRONZE SHUT-OFF VALVES

UL listed and designed as safe shut-off valve for LP gas, natural gas, flammable
liquids and heated oil. Features easy quarter-turn ON/OFF, a large port to
reduce pressure drop and NPT connections.
FEATURES UL LISTED
RPTFE seats and seals YQNZ - UL1477
Rated 600 psig CWP, non-shock YRBX - UL842
250 psig LP Gas YRPV - UL842
Tee handle (-07) YSDT - UL125
Latch lock handle (-27) MHKZ - UL842
Oxygen cleaned (-57)

80-101-01 1/4 0.37 1.03 2.06 1.75 3.87
80-102-01 3/8 0.37 1.03 2.06 1.75 3.87
80-103-01 1/2 0.50 1.12 2.25 1.81 3.87
80-104-01 3/4 0.68 1.50 3.00 2.12 4.87
80-105-01 1 0.87 1.68 3.37 2.25 4.87
80-106-01 1-1/4 1.00 2.00 4.00 2.62 5.50
80-107-01 1-1/2 1.25 2.18 4.37 2.87 5.50
80-108-01 2 1.50 2.34 4.68 3.06 5.50
80-109-01 2-1/2 2.50 3.25 6.50 4.12 8.00
80-100-01 3 2.50 3.37 6.75 4.12 8.00
90-100 SERIES UL LISTED UNI-BODY BRONZE THREADED BALL VALVE

A compact valve thats UL listed at 400 psig CWP, non-shock for fuel, inert
gases and flammable liquids. Features ASTM Grade Bronze body, RPTFE seats
and seals.
FEATURES UL LISTED
Blowout-proof stem design YQNZ - UL1477
One piece bronze body YRBX - UL842
Optional tee handle (-07) YRPV - UL842
Reduced port
90-103-01A 1/2 0.37 1.14 2.15 1.68 3.87
90-104-01A 3/4 0.50 1.36 2.61 1.75 3.87
90-105-01A 1 0.62 1.50 2.90 2.00 4.87
90-106-01A 1-1/4 0.81 1.81 3.50 2.18 4.87
90-107-01A 1-1/2 1.00 2.06 3.79 2.62 5.50
90-108-01A 2 1.25 2.43 4.42 2.81 5.50
37
BALL VALVES
78-256 SERIES MULTI PURPOSE SHUT-OFF VALVE WITH SURFACE MOUNTING EARS
Excellent for use with liquid fuels and often specified as a fuel tank shut-
off valve in marine applications. All wetted parts are brass or cast bronze.
Mounting ears for easy, positive installation.
FEATURES
Tested to 100 psig air under water
Optional tee handle
NPT threaded, both ends

78-248-01 1/4 0.43 1.12 2.25 1.78 3.87 0.93 1.87
78-250-01 3/8 0.43 1.12 2.25 1.78 3.87 0.93 1.87
78-256-01 1/2 0.50 1.12 2.25 1.78 3.87 0.93 1.87
78-438-01 3/4 0.68 1.50 3.00 2.12 4.87 1.06 2.12
77G-UL SERIES FULL PORT CSA & UL BRONZE GAS SHUT-OFF VALVES
UL and CSA listed fuel shut off valve that features a durable bronze body,
premium multi-fill MPTFE seats and stem packing, and a Solid Ball design
that delivers true full port flow performance.
FEATURES UL LISTED
Blowout-proof stem design MHKZ
ASTM B584 Bronze YSDT
Maximum body pressure: 600 psig CWP YQNZ
CSA Rating: 125 psig YRBX
CSA Rating: -20F to 150F YRPV
UL Rating: 250 psig max @ 125F UL LISTED
MSS SP-110 ball valves YRPV7
CSA to ASME B16.33, 125 YRBX7
CGA 3.16-M88, 125 MHKZ7
YSDT7

Wt.
77G-103-UL 1/2 0.50 1.19 2.35 1.80 3.74 0.68
77G-104-UL 3/4 0.75 1.42 2.74 1.98 4.78 1.26
77G-105-UL 1 1.00 1.64 3.18 2.18 4.78 2.08
D
38
BALL VALVES
GB-10 SERIES CSA GAS SHUT-OFF VALVES

Manual shut-off valves engineered specifically for low pressure gas service.
Canadian Standard Association design and capacity certified with American-
made quality. High-copper content body, chrome-plated ball, and PTFE seats.
FEATURES
Complies with ANSI Z21.15, CR91-002, and ASME 16.44
Use with natural, manufactured, mixed and liquefied petroleum
gases, LP gas-air mixtures
Standard, yellow die-cast
G
Zinc wing handle.
Temperature range: 32F - 125F at pressures of 1/2 and 5 psig
Standard die-cast zinc wing handle (-01), epoxy coated
Lever (-L1) or tee handle (-T1) options
Made in USA
F Dimensions (in.)
Model Size Connection
BTU/
B Number (in.) Hr* A B C D E F G
51GB-201 3/8 3/8 NPT 318,700 2.04 1.06 0.38 3.85 2.24 2.20 0.81
51GB-301 1/2 1/2 NPT 623,750 2.24 1.18 0.50 3.85 2.30 2.24 0.81
A 51GB-401 3/4 3/4 NPT 1,265,000 2.97 1.55 0.69 4.75 2.85 2.90 1.00
D 51GB-501 1 1 NPT 2,037,500 3.33 1.81 0.88 4.75 3.10 3.15 1.00
* Capacity based on a gas having a heating value of 1000 Btu/cubic feet and an S.G. of
0.64 at a P.D. of 1 W.C.
Optional Stainless
Steel lever handle E
B
GB-15 SERIES GAS BALL VALVE APOLLO INTERNATIONALTM

Designed for natural gas, manufactured and mixed gas, liquefied petroleum
gases and LP gas-air mixture applications.
APPROVALS
ANSI Z21.15 (Appliance & Hose)/CGA9.1(1/2 psi)
ASME B16.44 (5 psi)
UL Guide YRBX (Flammable Liquid Shut-Off )
UL Guide MHKZ (Manual Valves)
UL Guide YRPV (Gas Shut-Off 250#)
GB-15 UL Guide YSDT (LP Gas)
Model Number Part Number Size & End Connection (in.)

GB-15 51GF301A 1/2 FNPT x 1/2 FNPT
GB-15 51GF401A 3/4 FNPT x 3/4 FNPT
39
BALL VALVES
GB-50 & GB-50A SERIES CSA GAS SHUT-OFF VALVES

Designed for main burner applications with cast-in single or dual pilot tap.
ASTM B584 bronze body, chrome-plated ball, brass stem, retainer and gland
screws for corrosion resistance.
FEATURES
For natural gas, manufactured and mixed Gas, liquefied petroleum
gases and LP gas-air mixtures
Rated pressures of 1/2 and 5 psig
Standard connection is FNPT x FNPT
High BTU capacity
GB-50 Reversible plated steel lever handle. Optional tee handle (-07)
APPROVALS
ANSI Z21.15, CGA9.1
ASME B16.44 (2 and 5 psig)
MSS-SP110
UL Guide YRBX
UL Guide MHKZ
UL Guide YRPV
UL Guide YSDT
GB-50A UL 125, UL 842
D
G
I
B H
C
F
G
A
Model No. Model No. Size Dimensions (in.) Capacity

Single Dual Tapping
Tapped Tapped (in.) A B C D E F G H I BTU/Hr.
50GB-301 -- 1/2 1/8 0.50 1.11 2.25 1.68 3.85 2.27 1.00 0.53 - 693,000
50GB-401 50GB-401A 3/4 1/8 0.75 1.26 2.67 1.93 3.85 2.72 1.12 0.75 2.24 1,258,000
50GB-501 50GB-501A 1 1/8 1.00 1.65 3.42 2.19 4.78 3.18 1.53 0.94 3.06 3,144,000
50GB-601 50GB-601A 1-1/4 1/8 1.25 1.87 3.86 2.37 4.78 3.56 1.62 1.15 3.24 6,441,000
50GB-701 50GB-701A 1-1/2 1/8 1.50 2.05 4.22 2.81 5.40 4.21 1.81 1.31 3.62 7,745,000
50GB-801 50GB-801A 2 1/8 2.00 2.48 5.02 3.18 5.40 4.93 2.18 1.68 4.36 14,741,000
50GB-5A1 50GB-5A1A 1 1/4 1.00 1.65 3.42 2.19 4.78 3.18 1.53 0.94 3.06 3,144,000
50GB-6A1 50GB-6A1A 1-1/4 1/4 1.25 1.87 3.86 2.37 4.78 3.56 1.62 1.15 3.24 6,441,000
50GB-7A1 50GB-7A1A 1-1/2 1/4 1.50 2.05 4.22 2.81 5.40 4.21 1.81 1.31 3.62 7,745,000
50GB-8A1 50GB-8A1A 2 1/4 2.00 2.48 5.02 3.18 5.40 4.93 2.18 1.68 4.36 14,741,000
* Note: Capacities based on 1000 Btu/cubic feet gas at 0.64 specific gravity, at a P.D. of 1 W.C.
40
BALL VALVES
78-124/78-125 SERIES 5-PORT TANK SELECTOR

Unique ball design allows for higher flow capacities. Five port construction
allows access to four tanks using only one valve.
FEATURES
Five NPT connections
Bronze ball valve with stainless steel Lever and Nut
PTFEseats and RPTFE stem packing
Stem packing adjustable for wear
Non-lubricated
50 psig pressure rating
Operation: four selected inlets feed one common outlet
Pointer on handle indicates the selected inlet
Easy mounting design
Series Size Dimensions (in.) Wt./100

Number (in.) A B C D E F G H (lbs.)
78-124-01 1/2 0.50 1.26 2.52 2.27 3.53 1.12 10-24 1.40 106
78-125-01A 3/4 0.75 1.56 3.12 2.93 3.87 1.53 1/4-20 1.98 264
41
BALL VALVES
economy plumbing/gas ball valves
77F/77FLF SERIES FULL PORT THREADED FORGED BRASS BALL VALVES

The Apollo 77F Series is a full port forged brass ball valve suitable for a wide range
of plumbing and heating applications. These NPT threaded or solder, 2-piece valves
combine reliable operation with maximum economy. Valves include most pertinent
agency approvals. Proudly Made in the USA.
FEATURES
Heavy pattern forged design Silicone free assembly
Full-port flow Made in USA, ARRA compliant
Superior RPTFE seats and packing Rating: 600 CWP (1/4 - 2)
Adjustable stem packing Rating: 400 CWP (2-1/2 - 4)
Blow-out proof stem Steam rating: 150 psi SWP
Corrosion resistant materials Vacuum service to 29 in. Hg
100% Factory tested
Large Diameter Popular lever options and
stainless steel trim available
77FLF FEATURES
Easily identifiable white handle NSF/ANSI 372 Lead Free
E
grip and blue lead free hang tag Rating: 600 CWP (1/4 - 2)
A EZ-Solder lead free brass Rating: 400 CWP (2-1/2 - 4)
PORT
Lead free dezincification Steam rating: 150 psi SWP
D
Resistant brass Vacuum service to 29 in. Hg

NSF/ANSI 61-G
Wt.
B
C
NPT
77F-101-01 77FLF-101-01 1/4" 0.38 0.81 1.62 1.61 2.85 0.3
77F-102-01 77FLF-102-01 3/8" 0.38 0.85 1.70 1.61 2.85 0.3
77F-103-01 77FLF-103-01 1/2" 0.50 1.14 2.25 1.66 2.85 0.5
77F-104-01 77FLF-104-01 3/4" 0.75 1.26 2.51 1.91 3.86 0.8
77F-105-01 77FLF-105-01 1" 1.00 1.60 3.20 2.11 3.86 1.3
77F-106-01 77FLF-106-01 1-1/4" 1.25 1.73 3.46 2.44 4.75 2.1
77F-107-01 77FLF-107-01 1-1/2" 1.50 2.00 4.00 2.91 5.42 3.2
77F-108-01 77FLF-108-01 2" 2.00 2.37 4.47 3.69 7.77 5.6
77F-109-01 77FLF-109-01 2-1/2" 2.50 2.99 5.98 4.14 7.77 12.8
77F-100-01 77FLF-100-01 3" 3.00 3.52 7.05 5.03 9.92 19.7
77F-10A-01 77FLF-14A-01 4" 4.00 3.83 7.65 5.70 14.78 25.5
Solder
77F-203-01 77FLF-203-01 1/2" 0.50 1.37 2.37 1.66 2.85 0.4
77F-204-01 77FLF-204-01 3/4" 0.75 1.72 3.13 1.91 3.86 0.9
77F-205-01 77FLF-205-01 1" 1.00 2.01 3.73 2.11 3.86 1.3
77F-206-01 77FLF-206-01 1-1/4" 1.25 2.07 3.97 2.44 4.75 2.0
Large Diameter 77F-207-01 77FLF-207-01 1-1/2" 1.50 2.42 4.69 2.91 5.42 3.3
77F-208-01 77FLF-208-01 2" 2.00 2.91 5.82 3.69 7.77 5.6
77F-209-01 77FLF-209-01 2-1/2 2.50 3.68 7.05 4.14 7.77 11.6
E E 77F-200-01 77FLF-200-01 3 3.00 4.26 8.15 5.03 9.92 19.3
77F-20A-01 77FLF-24A-01 4 4.00 4.82 9.57 5.70 14.78 25.6
A A
APPROVALS
D
D
MSS-SP-110
IAPMO IGC-157 Ball Valves
CGA 3.16 (125 PSI)
CGA CR91-002 (5 PSI) FM 1140 (1/4 2)
B B ANSI Z21.15/CSA 9.1 (1/2 PSI) UL Guides: YSDT, MHKZ, YQNZ,
C C ASME B16.44 (5 PSI) YRBX & YRPV
ASME B16.33 (125 PSI) (1/2 2) UL Guide VQGU (1/4 2)
42
BALL VALVES
94A SERIES APOLLO INTERNATIONALTM ECONOMY FULL PORT BALL VALVES

These full port ball valves with forged brass body are UL listed and CSA
approved. Ideal for general purpose non-potable applications including air,
gas, HVAC, irrigation, fire protection, etc.
FEATURES
Adjustable stem packing nut
Meets MSS SP110 requirements
600 CWP non-shock (1/4 - 2)
400 CWP non-shock (2-1/2 - 4)
2-1/4 memory stop option
100% Factory Tested
Lead Free option (94ALF-A)
APPROVALS
CSA listed (File # 226234) per the following standards:
CAN 1-9.1 1/2 psig
CGA 3.16 125 psig
CGA CR91-002 5 psig
ANSI Z21.15 1/2 psig
ASME B16.44 5 psig
ANSI/ASME B16.33 125 psig
UL listed
Guides YQNZ, YRBX, YRPV,
YSDT and MHKZ (1/4 - 4 NPT only)
UL 258 VQGU Fire Protection Trim & Drain 175#
max (1/4 2)
FM 1140 Fire Protection Quick Opening Valves
* Gas approvals apply to NPT models only
Wt.
NPT
94A-101-01 1/4" 0.395 1.746 1.840 3.543 0.33
94A-102-01 3/8" 0.407 1.756 1.840 3.543 0.30
94A-103-01 1/2" 0.583 2.047 1.921 3.543 0.44
94A-104-01 3/4" 0.748 2.362 2.087 3.780 0.66
94A-105-01 1" 0.945 2.756 2.559 4.528 1.10
94A-106-01 1-1/4" 1.260 3.307 2.953 4.528 1.57
94A-107-01 1-1/2" 1.575 3.661 3.346 5.512 2.40
94A-108-01 2" 1.969 4.181 3.681 5.512 3.37
94A OPTIONS 94A-109-01 2-1/2" 2.520 5.378 4.764 8.661 7.60
94A-100-01 3" 2.953 6.039 5.079 8.661 9.36
Replacement 2-1/4 Stem Extension
Size 94A-10A-01 4" 3.898 7.386 5.866 9.606 16.85
Handles + Memory Stop
1/4-3/8 W932400 78217101 Solder
1/2 W932500 78217201 94A-203-01 1/2" 0.583 2.047 1.839 3.543 0.630 0.38
3/4 W936000 78217301 94A-204-01 3/4" 0.748 2.748 1.996 3.780 0.878 0.64
1 W932600 78217401 94A-205-01 1" 0.945 3.228 2.441 4.528 1.130 0.99
1-1/4 W932700 78217501 94A-206-01 1-1/4" 1.260 3.819 2.854 4.528 1.378 1.40
1-1/2-2 W932800 78217601 94A-207-01 1-1/2" 1.575 4.425 3.169 5.512 1.630 2.17
2-1/2-3 W932900 78217701 94A-208-01 2" 1.969 5.315 3.449 5.512 2.130 2.97
4 W933000 78217801 94A-209-01 2-1/2" 2.520 6.283 4.764 8.661 2.630 6.36
- Kits do not include stem nut 94A-200-01 3" 2.953 7.150 5.079 8.661 3.130 8.32
- Replacement handles are not UL marked 94A-20A-01 4" 3.945 9.276 5.866 9.606 4.130 15.78
43
BALL VALVES
94ALF-A SERIES APOLLO INTERNATIONALTM ECONOMY FULL PORT BALL VALVES

These Lead Free ball valves with forged DZR brass body are UL listed and CSA
approved. Ideal for plumbing and heating, fuel gas, fire protection and other
general purpose applications.
FEATURES
Lead Free* materials and certification
Solders like standard brass
Distinctive white Lead Free handle grip and blue Lead Free hang tag
2-Piece, Full-Port design
Blow-out Proof Stem
Adjustable Stem Packing Nut
Multiple agency approvals
Valve Design Rating: 600 CWP 1/4 to 2 , 400 CWP 2-1/2 to 4
Temperature Range: -20F to 366F
100% Factory Tested
NPT x NPT
APPROVALS
D
MSS SP-110 - Ball Valves
NSF/ANSI 61-G Water Quality IAPMO
C NSF/ANSI 372 Lead Free
IAPMO IGC 157 (cUPC)
A ANSI Z21.15 ( psi) (CSA 9.1) (1/4 2)
ASME B16.44 (5 psi) (CR91-002) (1/4 2)
ASME B16.33 (125 psi) (CGA 3.16) (1/4 2)
B
UL: Guides YQNZ, YRBX, YRPV, YSDT and MHKZ (1/4 - 4 NPT only)
Solder x Solder UL 258 VQGU Fire Protection Trim & Drain 175# max (1/4 2)
D FM 1140 (1/4 - 2 NPT & Solder) Fire Protection Quick Opening Valves
Note: Gas approvals apply to NPT valves only
C LF Model Size Dimensions (in.)

Wt.
E A NPT
94ALF-101-01A 1/4" 0.39 1.76 1.73 3.54 - 0.29
B 94ALF-102-01A 3/8" 0.39 1.76 1.73 3.54 - 0.30
94ALF-103-01A 1/2" 0.59 2.05 1.94 3.54 - 0.44
94ALF-104-01A 3/4" 0.75 2.36 2.11 3.78 - 0.71
94ALF-105-01A 1" 0.95 2.76 2.58 4.53 - 1.10
94ALF-106-01A 1-1/4" 1.26 3.31 2.96 4.53 - 1.63
94ALF-107-01A 1-1/2" 1.58 3.66 3.37 5.51 - 2.41
94ALF-108-01A 2" 1.97 4.18 3.70 5.51 - 3.66
94ALF-A OPTIONS 94ALF-109-01A 2-1/2" 2.52 5.38 4.76 8.66 - 7.60
Replacement 2-1/4 Stem Extension 94ALF-100-01A 3" 2.95 6.04 5.08 8.66 - 9.60
Size 94ALF-10A-01A 4" 3.90 7.39 5.86 9.61 - 21.00
Handles + Memory Stop
1/4-3/8 W234700 78217101 Solder
1/2 W234800 78217201 94ALF-203-01A 1/2" 0.59 2.05 1.84 3.54 0.63 0.40
3/4 W234900 78217301 94ALF-204-01A 3/4" 0.75 2.75 2.00 3.78 0.88 0.68
1 W235000 78217401 94ALF-205-01A 1" 0.95 3.23 2.45 4.53 1.13 1.15
1-1/4 W235100 78217501 94ALF-206-01A 1-1/4" 1.26 3.82 2.86 4.53 1.38 1.53
1-1/2-2 W235200 78217601 94ALF-207-01A 1-1/2" 1.57 4.43 3.17 5.51 1.63 2.31
2-1/2-3 W235300 78217701 94ALF-208-01A 2" 1.96 5.38 3.49 5.51 2.13 3.77
4 W273800 78217801 94ALF-209-01A 2-1/2" 2.52 6.28 4.76 8.66 2.63 6.79
- Replacement handles are not UL marked 94ALF-200-01A 3" 2.92 7.15 5.08 8.66 3.13 8.67
94ALF-20A-01A 4" 3.90 9.28 5.87 9.61 4.13 16.67
44
BALL VALVES
95ALF SERIES FULL-PORT LEAD FREE BRASS STOP & WASTE BALL VALVE
The Apollo InternationalTM 95ALF Lead Free forged DZR brass ball valves
combine reliable operation with maximum economy. Ideal for plumbing or
hydronic systems where draining is required. Valves are certified by IAPMO
and ANSI 3rd party certified lead free.
FEATURES
Lead Free materials and certification
Adjustable stem packing nut
Drain port with finger tight shut-off
Fast, quarter-turn operation
Valve Design Rating: 600 CWP
R
NAME:
Temperature Range: 32F to 250F
D
A IAPMO IGC157
MAT'L:
NPT x NPT NSF/ANSI 61-G Water Quality

atter disclosed therein is the property of Conbraco Industries, Inc. and is not to be
sed to others without the expressed written permission of Conbraco Industries, Inc.
C
A
A B NPT
D
95ALF-103-01 1/2 0.59 2.24 1.78 3.74 -
Solder x Solder 95ALF-104-01 3/4 0.79 2.53 2.09 3.94 -
C
95ALF-105-01 1 0.98 3.15 2.36 4.33 -
SECTION A-A Solder
E A 95ALF-203-01 1/2 0.59 2.12 1.78 3.74 0.63
95ALF-204-01 3/4 0.79 2.87 1.94 3.94 0.88
B 95ALF-205-01 1 0.98 3.53 2.36 4.33 1.13
45
BALL VALVES
apolloxpress ball valves
77W SERIES APOLLOXPRESS BRONZE AND LEAD FREE BRONZE FULL PORT BALL VALVES
Apollo 77W Series APOLLOXPRESS ball valves install in seconds, but the
valve and the connection are made to last. Ideal for mechanical and heating
systems. Not for use with natural gas.
FEATURES
Full port Popular lever options and
Rigid XL Press Tool compatible stainless steel trim available
Leak Before Press technology Made in the USA
250 CWP, non-shock to 250F max.
MSS SP-110 ball valves
Excellent for hydronic heating
(90% glycol max)

Wt.
77W-103-01 1/2 0.50 1.54 3.08 1.50 3.74 0.6
77W-104-01 3/4 0.75 1.78 3.55 2.01 4.78 1.1
77W-105-01 1 1.00 1.93 3.86 2.20 4.78 1.8
77W-106-01 1-1/4 1.25 2.44 4.87 3.13 7.04 4.3
77W-107-01 1-1/2 1.50 2.91 5.81 3.10 7.04 4.6
77W-108-01 2 2.00 3.74 7.47 3.48 7.04 8.2
77WLF SERIES APOLLOXPRESS LEAD FREE BRONZE FULL PORT BALL VALVES
Apollo 77WLF Series APOLLOXPRESS ball valves install in seconds, but the
valve and the connection are made to last. Ideal for most plumbing and
heating systems including potable water. Not for use with natural gas.
FEATURES
Full port Adjustable stem packing
Rigid XL Press Tool compatible Excellent for hydronic heating
Leak Before Press technology (90% glycol max)
250 CWP, non-shock to 250F max. Popular lever options and
MSS SP-110 ball valves stainless steel trim available
NSF/ANSI 61-8 (2010) compliant Made in the USA
Wt.
77WLF-103-01 1/2 0.50 1.54 3.08 1.50 3.74 0.6
77WLF-104-01 3/4 0.75 1.78 3.55 2.01 4.78 1.1
77WLF-105-01 1 1.00 1.93 3.86 2.20 4.78 1.8
77WLF-106-01 1-1/4 1.25 2.44 4.87 3.13 7.04 4.3
77WLF-107-01 1-1/2 1.50 2.91 5.81 3.10 7.04 4.6
77WLF-108-01 2 2.00 3.74 7.47 3.48 7.04 8.2
46
BALL VALVES
77W-HC SERIES APOLLOXPRESS x HOSE CAP & CHAIN BALL VALVE

Designed for direct mechanical connection to ASTM B88-Type K,L, and M
copper tubing in the hard drawn condition for sizes 1/2-3/4. Valves feature
a 3/4 hose thread connection with heavy brass cap to protect the threads
and is full pressure rated. Not for use with natural gas.
FEATURES
Full port
Rigid XL Press Tool compatible
Leak Before Press technology
MSS SP-110 ball valves
NSF/ANSI 61-G compliant (77WLF-HC)
77WLF supplied with Easily Identifiable White Handle Grip and Blue
Lead Free Hang Tag
250 CWP, non-shock to 250F max.
Excellent for hydronic heating (90% glycol max)
Compatible with most 77C Series options
Heavy brass dust cover is full pressure rated
Popular lever and trim options available
Made in the USA
Model LF Model Size Dimensions (in.) Wt.
Number Number (in.) A B C (lbs.)
77W-103-HC 77WLF-103-HC 1/2 1.80 3.12 1.54 0.61
77W-104-HC 77WLF-104-HC 3/4 2.01 3.45 1.72 1.09
77V SERIES APOLLOXPRESS PRESS END BRASS BALL VALVE

The APOLLOXPRESS 77V Series two-piece press ball valve is ideal for installation
in most HVAC systems. Features Leak Before Press technology and 250 psig
maximum working pressure. Proudly Made in the USA.
FEATURES
2 piece, heavy pattern forged design Corrosion resistant materials
Full-port flow Silicone free assembly
Max. operating pressure 250 psi 100% factory tested
Temperature range: 0F - 250F MSS SP-110 Ball Valves
Superior RPTFE seats and packing Directive 2011/65/CE (RoHS)
Adjustable stem packing Popular lever options and SS
Rigid XL press tool compatible trim available
2-1/2 - 4 are XLC compatible Made in USA, ARRA Compliant
Blow-out proof stem
Large Diameter Wt.
77V-103-01 1/2" 0.50 1.57 2.89 1.66 2.85 0.4
77V-104-01 3/4" 0.75 1.90 3.63 1.91 3.86 0.9
77V-105-01 1" 1.00 2.20 3.88 2.11 3.86 1.2
77V-106-01 1-1/4" 1.25 2.23 4.22 2.44 4.75 2.3
77V-107-01 1-1/2" 1.50 2.84 5.45 2.91 5.42 3.4
77V-108-01 2" 2.00 3.40 6.57 3.69 7.77 6.0
77V-109-01 2-1/2" 2.50 4.26 8.04 4.13 7.77 12.0
77V-100-01 3" 3.00 5.10 9.45 5.03 9.92 19.5
77V-10A-01 4" 4.00 5.20 10.35 5.70 14.78 26.0
47
BALL VALVES
77VLF SERIES LEAD FREE APOLLOXPRESS PRESS END BRASS BALL VALVE
The APOLLOXPRESS 77VLF Series Lead Free two-piece press ball valve is ideal
for installation in most plumbing and heating systems, including potable
water. Features Leak Before Press technology and 250 psig maximum
working pressure. Proudly Made in the USA.
FEATURES
Lead Free, ANSI 3rd party certified 100% factory tested
2 piece, heavy pattern forged design Made in USA, ARRA Compliant
Dezincification resistant materials Maximum operating pressure 250 psi
Easily identifiable white handle Temperature Range: 0F - 250F
grip and blue Lead Free hang tag MSS SP-110 Ball Valves
Full-port flow NSF/ANSI 61-G
Superior RPTFE seats and packing NSF/ANSI 372 Lead Free
Adjustable stem packing IAPMO IGC-157 Ball Valves
Rigid XL press tool compatible Directive 2011/65/CE (RoHS)
2-1/2 - 4 are XLC compatible Popular lever options and
Blow-out proof stem stainless steel trim available
Large Diameter Silicone free assembly
Wt.
77VLF-103-01 1/2" 0.50 1.57 2.89 1.66 2.85 0.4
77VLF-104-01 3/4" 0.75 1.90 3.63 1.91 3.86 0.9
77VLF-105-01 1" 1.00 2.20 3.88 2.11 3.86 1.2
77VLF-106-01 1-1/4" 1.25 2.23 4.22 2.44 4.75 2.3
77VLF-107-01 1-1/2" 1.50 2.84 5.45 2.91 5.42 3.4
77VLF-108-01 2" 2.00 3.40 6.57 3.69 7.77 6.0
77VLF-109-01 2-1/2" 2.50 4.26 8.04 4.13 7.77 12.0
77VLF-100-01 3" 3.00 5.10 9.45 5.03 9.92 19.5
77VLF-14A-01 4" 4.00 5.20 10.35 5.70 14.78 26.0
48
BALL VALVES
apolloxpress ball valves &
lead free apollopex ball valves
94VLF SERIES LEAD FREE APOLLOXPRESS PRESS END BRASS BALL VALVE
The CONBRACO INTERNATIONAL 94VLF Series Lead Free* two-piece press ball
valve is ideal for installation in most plumbing and heating systems, including potable water.
FEATURES PERFORMANCE RATING
Lead Free*, ANSI 3rd party certified Maximum Operating Pressure 250 psig
Full-port flow Temperature Range: 0F - 250F
PTFE seats and packing APPROVALS
Adjustable stem packing MSS SP-110 Ball Valves
Rigid XL press tool jaw compatible NSF/ANSI 61 Section 8
(1/2 2) NSF/ANSI 372 - 3rd party certified
Rigid XLC press tool jaw compatible IAPMO IGC-157-2013 Ball Valves
(2-1/2 - 4)
Corrosion resistant materials
APPROVED APPLICATIONS
Water including potable water
100% factory tested
Hydronic heating (90% glycol max)
2 year warranty
Not suitable for flammable gas service
Designed for direct mechanical
1/2 2 2-1/2 4 connection to ASTM B88-Type K, L,
and M copper tubing in the hard
drawn condition.
Not compatible with soft annealed
copper tubing.
DIMENSIONS
MODEL SIZE DIMENSIONS WT. CARTON
NUMBER (IN.) A A B B C C D D E E (LBS.) QTY.
(IN.) (MM) (IN.) (MM) (IN.) (MM) (IN.) (MM) (IN.) (MM)
94VLF-103-01 1/2" .50 14.5 1.87 47.5 3.75 95 1.65 42 3.75 95 0.5 50
94VLF-104-01 3/4" .75 19 2.23 56.7 4.46 113.4 1.91 48.5 4.33 95 1 40
94VLF-105-01 1" 1.00 25 2.34 59.5 4.69 119 2.28 58 4.33 110 1.1 20
94VLF-106-01 1-1/4" 1.25 32 2.81 71.5 5.63 143 2.76 70 5.12 130 1.9 20
94VLF-107-01 1-1/2" 1.50 39 2.96 75.3 5.93 150.6 2.95 75 5.12 130 2.4 16
94VLF-108-01 2" 2.00 50 3.50 89 7.01 178 3.50 89 6.34 161 4.2 8
94VLF-109-01 2-1/2" 2.50 62 3.50 89 7.01 178 4.61 117 9.45 240 7.8 1
94VLF-100-01 3" 3.00 74.00 3.88 103.50 8.15 207.00 4.96 126.00 9.45 240 11.20 1.00
94VLF-10A-01 4" 4.00 98.50 4.98 126.50 9.96 253.00 5.91 150.00 9.45 240 21.20 1.00
Lead Free APOLLOPEX Ball Valve

94XLF SERIES BRASS PEX BALL VALVE
The Apollo International 94XLF Lead Free* DZR forged brass ball
valves combine reliable operation with maximum economy. Ideal for
plumbing and heating applications including potable water. Valves
are ANSI 3rd party Lead Free* certified and listed to NSF 14, NSF 61
and NSF 372.
FEATURES
Lead Free* DZR materials and Double o-ring stem seal
E
certification Blow-out proof stem design
ASTM F1807 PEX design Silicone free assembly
White handle grip identifies lead
free construction
F
Model Size Dimensions (in.) Wt.

D
Number (in.) B C D E F (lbs.)

B
B
94XLF-103-01 1/2 0.65 2.52 .47 3.17 1.49 .25
C
94XLF-104-01 3/4 0.65 2.62 .67 3.17 1.57 .41
94XLF-105-01 1 0.80 2.91 .86 3.17 1.57 .57
49
BALL VALVES
50

Cat Cpcaball

Uploaded by

Copyright:

Available Formats

Cat Cpcaball

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Cat Cpcaball

Uploaded by

Copyright:

Available Formats

BALL

Full-port design through 2-1/2

Therma-Seal insulating tee handle (-11)

SS vented ball and stem(77C140 and 77C240 series)

EXP. NO. SCALE: DRN: DATE:

Also available in a Lead Free version as the 77CLF Series.

E Model Size Dimensions (in.) Wt.

77C-101-01A 1/4 0.37 .095 1.80 1.62 2.86 - - 5 0.6

EXP. NO. SCALE: DRN: DATE: CHKD: APP'D: NO. REV.

77C-108-01A 2" 2.00 2.43 4.85 3.83 7.06 - - 389 8.1

Full-port design through 2-1/2

2-1/4 stem extension (-04)

CS tee handle (-07)

SS vented ball and stem(77CLF140-A and 77CLF240-A series)

Other handle options available

LF Model Size Dimensions (in.) Wt.

77CLF-101-01A 1/4 0.37 .095 1.80 1.62 2.86 - - 5 0.6

77CLF-103-01A 1/2" 0.50 1.15 2.29 1.79 3.74 - - 16 0.6

77CLF-105-01A 1" 1.00 1.53 3.24 2.19 4.88 - - 68 1.8

77CLF-109-01A 2-1/2" 2.50 3.12 6.02 4.51 8.06 - - 503 16.2

70-100/200 SERIES BRONZE BALL VALVE

Model Size Dimensions (in.)*

NOTE: 1/4, 3/8, and 1/2 are full port.

Model Size Dimensions (in.)*

NOTE: 1/4, 3/8, and 1/2 are full port.

70LF-100/200 SERIES LEAD FREE BRONZE BALL VALVE

LF Model Size Dimensions (in.)*

NOTE: 1/4, 3/8, and 1/2 are full port.

LF Model Size Dimensions (in.)*

NOTE: 1/4, 3/8, and 1/2 are full port.

Model LF Model Size Dimensions (in.)

70-300/400 SERIES BALL VALVE WITH FNPT x UNION END

70-600 SERIES THREADED 3-WAY DIVERTER BALL VALVE

70-800 SERIES MALE X FEMALE NPT BALL VALVE

70-900 SERIES 3-WAY DIVERTER VALVE WITH SOLDER ENDS

Model Size Dimensions (in.)

32-100 SERIES REGULAR PORT THREADED END BRONZE BALL VALVE

2-1/4 STANDARD BALL VALVE WITH STEM EXTENSION

-11 THERMA-SEAL HANDLE - NEW UL 2043 LISTING

-16 or -58 CHAIN LEVER BALL VALVES

-30 CAM-LOCK HANDLE

-32 and -83

-41 BALL VALVE WITH AUTOMATIC DRAIN

STAINLESS STEEL OVAL HANDLE

71-100 SERIES BALL VALVE WITH MOUNTING PAD

Model Size Dimensions (in.)

E E 71-105-01 1 0.87 1.68 3.37 2.25 4.87 0.87 1.37 10-24 NC

71-108-01 2 1.50 2.34 4.68 3.06 8.00 0.93 1.50 1/4-20 NC

NPT BOTH ENDS

71-500 SERIES CAST BRONZE VALVE WITH SPRING RETURN HANDLE

Model Size Dimensions (in.)

73A-100 SERIES FORGED CARBON STEEL BALL VALVE

Model Size Dimensions (in.)

76F-100-A SERIES STAINLESS STEEL FULL PORT BALL VALVE

Model Size Dimensions (in.)

75-100-41 SERIES PADLOCKING BALL VALVE WITH AUTOMATIC DRAIN

SIZES 1/4" - 1-1/4"

1-1/2" & 2": 5/16"-24 UNF

OA 77-103-01 1/2 0.50 1.12 2.25 1.81 3.87 0.50 1.12 15