RCC Open Drain - Pamarru

DESIGN OF R.C.C. OPEN DRAIN ( clear height= 1.80 m, overall width=2.
46m)
f f
a
b
e
TYPICAL CROSS-SECTION
1.0 Design Data
1.1 Preliminary Dimensions :
Clear Span 'b' = 2.00 m

Clear Height 'a' = 1.80 m
Wall Thickness 'f' = 0.230 m
Base Thickness 'e' = 0.230 m
Overall height 'H' = 2.03 m
Overall width 'W' = 2.46 m
1.2 Material Properties
Density of backfill soil s = 20 kN/m3

Density of Concrete c = 25 kN/m3
S.B.C. of Soil qs = 50 kN/m2
Angle of Internal friction for back fill = 30 degree
friction angle between wall & backfill = 20 degree
Angle of Inclination of back of wall = 0 degree
Slope of backfill with horizontal i 0 degree
Permissible Settlement = 40.00 mm
Height of surcharge = 1.20 m
1.3 Design Parameters
Grade of Concrete = M25

Grade of Steel = Fe500
Clear Cover for earth face structural component = 50 mm
Clear Cover for inside face structural component = 50 mm
Clear Cover for bottom slab = 50 mm
Characteristic comp. strength of Concrete (fck) = 25.00 N/mm2
Yield strength of Steel ( fy ) = 500 N/mm2
2.0 Load Calculation
2.10 Dead Load of the Structure 'DL'
U.D.L on vertical wall = 10.35 kN/m

U.D.L on base slab = 5.75 kN/m
2.20 Dead Load on Bottom Slab due to Soil Silting
Thickness of earth fill due to silting = 0.3 m

Load (UDL) on bottom slab = 0.3 * 20 = 6 KN/m
2.30 Horizontal Earth Pressure
Critical loading condition will be the situation when box will be subjected to earth pressure
due to saturated backfill and there will be no water inside the box.
cos2 ( )
Co-efficient of Active Earth Pressure= (Ka)static 2
sin( )sin( i)
cos cos( )1
2

cos( )cos( i)
= 0.297
Earth-pressure at a depth 'h' from the top of vertical wall=Ka. s.h kN/sq.m
Horizontal force on wall due to Earth pressure at variuos level is shown in the load diagram below.
2.40 Live Load Surcharge

Equivalent height = 1.20 m
Uniform Intensity of loading = = 7.13 KN/m2
3.0 Structural Analysis

The structure is analysed for variuos load acting on it using structural-design software ''STAAD.ProV8i "
modelling it along the center lines of walls and slab. Spring type supports are adopted which are applied
various nodes along bottom slab. Stiffness of the support are calculated based on modulus of subgra
reaction.
10.35 10.35
2.23
11.75
10.69 10.69
11.38 7.13 7.13 11.38
LOAD DIAGRAM
4 3
8 7
5 9 10 11 12 13 14 6
1 2
Figure: STADD Discretisation of BOX Geometry.
Spring Constant= 1250 kN/m2 per m width

Nos. of springs provided= 10
Spring constant at end supports 1,2= 71.875 kN/m per m width

Spring constant at penultimate supports 5,6= 250.4464286 kN/m per m width
Spring constant atintermediate supports 9 to 14= 357.1428571 kN/m per m width
4. Design of Drain
a) Design of Vertical wall

Factored bending moment Mu(From analysis) = 30.1KN-m
Effective depth required d = Mu/0.133fckb = 95.15mm
Over all depth provided = 230.00mm

Effective depth provided(Assuming 50mm cover) d = 172.0mm
Mu/bd2 = 1.017
From table 3 of SP 16,percentage of steel required = 0.255
Area of steel required = 439sqmm
Hence provide 10mm dia HYSD bars@ 150mm c/c spacing
Hence Ast provided = 523sqmm
Check for shear:-
The critical section for beam shear is at distance of 'd' from the face of the support
Hence,the factored design shear force V Fd = 36.80KN

at a distance 'd' from the face of the support
Nominal shear stress Tv = 0.210N/sqmm <2.8 N/sqmm

(As per Table 20 of 1S 456)
Hence,the section is safe from shear point of view
Assumed percentage area of the steel reinforcement = 0.30%
The design shear strength of concrete for the above steel percentage from
Table 19 of IS 456 is
0.328
0.328>0.21
Hence,the depth provided is safe from beam shear point of view
Hence,no shear reinforcement is required.
Provide temperature re inforcement @ 0.12%
Area required = 276.00sqmm
Provide 1/3rd of above reinforcement on earthen side = 92.00sqmm

Provide 8mm dia @ 200mm c/c on earthen side
Provide 2/3rd of above reinforcement on other side = 184.00sqmm
Provide 8mm dia @ 150mm c/c on other side
Provide 10mm bars at 300mm c/c vertically on the inner face to support horizontal rods
b) Design of base slab

Factored bending moment Mu(From analysis) = 30.5KN-m
Effective depth required d = Mu/0.133fckb = 95.78mm
Over all depth provided = 230.00mm
Effective depth provided(Assuming 50mm cover) d = 172.0mm
Mu/bd2 = 1.031
From table 3 of SP 16,percentage of steel required = 0.255
Area of steel required = 439sqmm
Hence provide 10mm dia HYSD bars@ 150mm c/c spacing at bottom
Check for shear:-
The critical section for beam shear is at distance of 'd' from the face of the support
Hence,the factored design shear force V Fd = 13.00KN

at a distance 'd' from the face of the support
Nominal shear stress Tv = 0.080N/sqmm <2.8 N/sqmm

(As per Table 20 of 1S 456)
Hence,the section is safe from shear point of view
Assumed percentage area of the steel reinforcement = 0.30%

The design shear strength of concrete for the above steel percentage from
Table 19 of IS 456 is
0.328
0.328>0.08
Hence,the depth provided is safe from beam shear point of view
Hence,no shear reinforcement is required.
Provide temperature re inforcement @ 0.12%
Area required = 276.00sqmm
Provide 10mm dia @ 250mm c/c on top
Provide distribution steel of 10mm @ 300mm c/c in other direction both top and bottom
Design dimensions and reinforcments :
Clear Reinforcemnt
thick. in
(span x Member
mm earth face water face distribution bar. b
height)
wall 230 T10 @ 150 c/c T10 @300 c/c T8 @ 200 & 150
2.00 x 1.80
base-slab 230 T10 @ 150 c/c T10 @ 250 c/c T10 @300 c/c
=2.46m)
e
2
sin( i)

cos( i)
m below.
STAAD.ProV8i " by
hich are applied at
dulus of subgrade
distribution bar. b/f
8 @ 200 & 150 c/c

T10 @300 c/c

RCC Open Drain - Pamarru

Uploaded by

Copyright:

Available Formats

RCC Open Drain - Pamarru

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

RCC Open Drain - Pamarru

Uploaded by

Copyright:

Available Formats

What are the design parameters considered for the open drain?

What are the design parameters considered for the open drain?

How is the structural analysis of the open drain carried out?

How is the structural analysis of the open drain carried out?

DESIGN OF R.C.C. OPEN DRAIN ( clear height= 1.80 m, overall width=2.

1.0 Design Data

1.1 Preliminary Dimensions :

Clear Span 'b' = 2.00 m

1.2 Material Properties

Density of backfill soil s = 20 kN/m3

1.3 Design Parameters

Grade of Concrete = M25

2.0 Load Calculation

2.10 Dead Load of the Structure 'DL'

U.D.L on vertical wall = 10.35 kN/m

2.20 Dead Load on Bottom Slab due to Soil Silting

Thickness of earth fill due to silting = 0.3 m

2.30 Horizontal Earth Pressure

2.40 Live Load Surcharge

3.0 Structural Analysis

Figure: STADD Discretisation of BOX Geometry.

Spring Constant= 1250 kN/m2 per m width

Spring constant at end supports 1,2= 71.875 kN/m per m width

a) Design of Vertical wall

Effective depth required d = Mu/0.133fckb = 95.15mm

Over all depth provided = 230.00mm

From table 3 of SP 16,percentage of steel required = 0.255

Area of steel required = 439sqmm

Hence provide 10mm dia HYSD bars@ 150mm c/c spacing

Hence Ast provided = 523sqmm

Check for shear:-

Hence,the factored design shear force V Fd = 36.80KN

Nominal shear stress Tv = 0.210N/sqmm <2.8 N/sqmm

Hence,the section is safe from shear point of view

Assumed percentage area of the steel reinforcement = 0.30%

Hence,the depth provided is safe from beam shear point of view

Hence,no shear reinforcement is required.

Provide temperature re inforcement @ 0.12%

Area required = 276.00sqmm

Provide 1/3rd of above reinforcement on earthen side = 92.00sqmm

Provide 2/3rd of above reinforcement on other side = 184.00sqmm

Provide 8mm dia @ 150mm c/c on other side

b) Design of base slab

Effective depth required d = Mu/0.133fckb = 95.78mm

Over all depth provided = 230.00mm

Effective depth provided(Assuming 50mm cover) d = 172.0mm

From table 3 of SP 16,percentage of steel required = 0.255

Area of steel required = 439sqmm

Hence Ast provided = 523sqmm

Check for shear:-

Hence,the factored design shear force V Fd = 13.00KN

Nominal shear stress Tv = 0.080N/sqmm <2.8 N/sqmm

Hence,the section is safe from shear point of view

Assumed percentage area of the steel reinforcement = 0.30%

Hence,the depth provided is safe from beam shear point of view

Hence,no shear reinforcement is required.

Provide temperature re inforcement @ 0.12%

Area required = 276.00sqmm