Tapered Beam

Tapered Beam Element
The Tapered Beam Element incorporated in the Finite Element Engine of MIDAS Family Programs is a
three-dimensional beam element shown in Fig. 1. Formulation of this beam element is based on the
following assumptions:
1. The beam cross-section is a closed solid (thick-walled) section

2. The element cross-section bending and shear centers are coincident.
3. The element is capable of resisting axial forces, bending moments about the two principal axes
in the plane of its cross-section, and twisting moments about its centroidal axis.
4. The transverse shear effects are modeled according to Timoshenko beam theory.
5. Torsional behavior is governed by the Poisons theory of torsion (warping is not allowed).
6. At the element ends can be hinges (member end-releases).
7. At the element ends can be member end-offsets along its local axes.
b yj
bzj w2 b xj
v2 u2
j
bzi
y
b yi w1
Z v1
Y u 1i
X b xi
Figure 1 A 3D Tapered Beam Finite Element
The changes in cross section area, shear area, and torsional moment of inertia along the tapered beam
element axis are assumed as follows:
A(x) = Ai + (Aj Ai)
As(x)= As,i + (As,j As,i)
Ixx (x)= Ixx,i + (Ixx,j- Ixx,i)

Also, the change in moment of inertia along the length of a tapered beam is assumed as,

I ( x ) = Ii +

( I j Ii

) x

L
where, 0 < x < L , and parameter is
1 - for linear

= 2 - for parabolic
.
3 - for cubic

According to the above equation, the stiffness varies more drastically along the axis with the increase in
the value of . In such a case, the overall stiffness of the member is smaller than that based on the linear
variation.
Here, for the sake of convenience, the formulation has been formalized for the 2D beam element with
uniform section (prismatic beam). The basic equilibrium equation for such element that defines the finite
element stiffness matrix can be presented as follows:
k11 0 0 k14 0 0 ui H i

k22 k23 0 k25 k26 vi Vi
k33 0 k35 k36 i M i
=
k44 0 0 u j H j
k55 k56 v j V j

Sym. k66 j M j
or in matrix form
Ku = f
where K is the stiffness matrix including terms that are defined using the standard finite element
procedure based on displacement method. However, in the case of a tapered beam, the calculation of
corresponding stiffness terms cannot be formalized and thus obtained by use of displacement method. So
here we are using the force method, which can be summarized as follows. First, we assume that H i = 1 ,
and all the displacements except for ui and the remaining loads at i-node are equal to 0, then the above
equation becomes,
k11 k14 ui 1
k =
14 k44 0 1
Accordingly, k11 is identical to 1/ui. This displacement can be calculated by introducing a unit axial load
while maintaining the j-end fixed as the axial direction based on the above equation of the assumed
stiffness variation. The principle of virtual work, the method of consistent displacement, etc. can be used
for calculations. If for example, the principle of virtual work is used, the equation then becomes,
L 1 1
ui = dx
0 EA ( x )
Following the above method and using the displacements calculated by introducing the unit shear force,
unit moment, etc. at the i-end and j-end, we can back calculate the stiffness terms of the tapered beam
element. First, if we apply a unit shear force at the i-end while maintaining the j-end fixed, we obtain,
k22 k23 vi1 1

k =
23 k33 i1 0
Similarly, introducing a unit moment at the i-end while maintaining the j-end fixed, the following is
obtained:
k22 k23 vi 2 0
k =
23 k33 i 2 1
Therefore,
k22 k23 vi1 vi 2 1 0

k =
32 k33 i1 i 2 0 1
1
k k23 1 0 vi1 vi 2
22 =
k32 k33 0 1 i1 i 2
Accordingly, we obtain the four terms of the stiffness matrix. At this point, the displacements due to unit
shear force and unit moment can be obtained by the following equations:
V1 ( x ) V1 ( x ) V2 ( x )V1 ( x )
2 2
L L L
vi1 = dx + dx vi 2 = dx
0 EI ( x ) 0 GAs ( x ) 0 EI ( x )
M1 ( x ) M 2 ( x ) M 2 ( x)
2
L L
i1 = dx i2 = dx
0 EI ( x ) 0 EI ( x )
where, V1(x) and M1(x) are the shear force and moment at the distance, x from the i-end due to the unit
shear force applied at the i-end; and V2(x) and M2(x) are the shear force and moment at the distance, x
from the i-end due to the unit moment applied at the i-end.
The remaining terms can be calculated by the same method noted above.

Tapered Beam

Uploaded by

Copyright:

Available Formats

Tapered Beam

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Tapered Beam

Uploaded by

Copyright:

Available Formats

Tapered Beam Element

1. The beam cross-section is a closed solid (thick-walled) section

Figure 1 A 3D Tapered Beam Finite Element

A(x) = Ai + (Aj Ai)

As(x)= As,i + (As,j As,i)

Ixx (x)= Ixx,i + (Ixx,j- Ixx,i)

where, 0 < x < L , and parameter is

k22 k23 vi1 1

k22 k23 vi1 vi 2 1 0

You might also like