Arteche Ds Trfmvguide en

REFERENCE GUIDE
INSTRUMENT
TRANSFORMERS
INDOOR / OUTDOOR
CAST RESIN CONSTRUCTION
This document may be subject to changes. Contact
ARTECHE to conrm the characteristics and
availability of the products described here.
MOVING TOGETHER
CONTENTS
Updates available at:
www.arteche.com/unitusa
The instrument transformers listed in this guide are the most common for the electrical
utilities and industries. ARTECHE has a much wider range of characteristics and models.
For any different detail than the ones listed, please contact ARTECHE or your local
representative/distributor.
GENERAL TECHNICAL DATA

APPLICATION DATA
ACCURACY STANDARDS
OTHER INFORMATION
600 V INSTRUMENT TRANSFORMERS

600 V CURRENT TRANSFORMER | 10
5 kV 34.5 kV INDOOR INSTRUMENT TRANSFORMERS

5 kV VOLTAGE TRANSFORMER | 32 15 kV COMBINED TRANSFORMER| 88
8.7 kV VOLTAGE TRANSFORMER | 36 25 kV COMBINED TRANSFORMER | 90
15 kV VOLTAGE TRANSFORMER | 38
34.5 kV VOLTAGE TRANSFORMER | 56
5 kV CURRENT TRANSFORMER | 64
8.7 kV CURRENT TRANSFORMER | 66
5 kV 69 kV OUTDOOR INSTRUMENT TRANSFORMERS &

METERING UNITS
5 kV VOLTAGE TRANSFORMER | 94 15 kV COMBINED TRANSFORMER AND
METERING UNITS | 174
25 kV COMBINED TRANSFORMER AND
METERING UNITS | 182
34.5 kV VOLTAGE TRANSFORMER | 120 34.5 kV COMBINED TRANSFORMER AND
46 kV VOLTAGE TRANSFORMER | 124 METERING UNITS | 190
Instrument Transformers | Reference Guide www.arteche.com

GENERAL
TECHNICAL
DATA
APPLICATION DATA
INTRODUCTION Phase-to-phase Voltage transformers (VR/VC/VX)
The V in the type name and the Y in the primary
The Purpose of instrument transformers:
voltage column of the data sheet indicate that the VT has
The purpose of instrument transformers is to reduce two fully insulated bushings, making it suitable for line-to-
the voltage and current of an electrical network to line connection.
standardized, non-hazardous levels.
27600/47804Y. This unit is rated for 27600 operating
They isolate operators and instruments from the Volts. It can be connected at 27600 Volts line-to-
high voltage circuits allowing a less hazardous ground on a 47804 Volt system (line-to-line Volts
work environment. Without these transformers, are 47804 V) OR it can be connected line-to-line on
measurements would require expensive insulated a system with 27600 V line-to-line. This unit is not
instrument panels. suitable for operation at 47804 Volts.
There are two types of instrument transformer:

46000/46000Y. This unit is rated for 46000 operating
Volts. It can be connected at 46000 Volts line-to-line.
Current transformers (CT): Under normal operating
conditions their secondary current is practically
proportional to the primary current, and its phase is RATING FACTORS
shifted by an angle close to zero.
Rating factors given in this brochure are standard at 30C
Voltage transformers (VT): Under normal operating Characteristics for different thermal loadings on request.
conditions the secondary voltage is practically
proportional to the primary voltage and its phase is
shifted by an angle close to zero. STANDARDS
All the instrument transformers listed in this guide comply
with the following standards where applicable:
CT VT
IEEE C57.132016. Standard Requirements for
Instrument transformers.
VT ANSI C12.11-2007. American National Standard for
Instrument transformers for Revenue Metering 10kV BIL
V
through 350 kV BIL (0.6 kV NSV through 69 kV NSV).
A
R
V CAN/CSA-C60044. Instrument Transformers.
IEC 61869. Instrument Transformers.
R
R
W
HOW TO SPECIFY INSTRUMENT
Figure 1: CT and VT diagram connection TRANSFORMERS
There are several parameters that must be specied when
ordering or requesting for proposals or quotations. If the
requirements needed ts exactly into the characteristics
VT VOLTAGE DESIGNATIONS listed in the data sheets of each model, it is enough to
mention the code. However, when non-standard equipment
Single-phase Voltage transformers (UR/UC/UX) will be needed, the following parameters must be specied:
The U in the type name and the GY in the primary Highest nominal voltage system
voltage column of the data sheet indicate that the VT has Basic impulse level (BIL)
one fully insulated bushing, making it suitable for line-to- Type of service (outdoor/indoor)
ground connection only. Frequency
40250/69000GY. This unit is rated for 40250 Ratio
operating Volts. It can be connected at 40250 Volts Only for current transformers
line-to-ground on a 69000 Volt system (line-to-line
Volts are 69000 V).
Continuous thermal current rating factor
Short-time thermal current (kA/1s)
34500/34500GY. This unit is rated for 34500 operating Class and burden
Volts. However, it can only be connected line-to-ground
on a 34500 V system. Therefore, the actual operating Only for voltage transformers
voltage of the unit would be 34500/3. The accuracy Rated continuous voltage
and thermal ratings of this unit are based on 34500 V. Rated voltage factor (30sec)
This is typical where there is a relay connected to the Total thermal burden
unit which should operate when there is a single line- Accuracy class and burden
to-ground fault. In this condition, the line-to-ground
voltage becomes equal to the line-to-line voltage.
www.arteche.com Instrument Transformers | Reference Guide

ACCURACY STANDARDS
CURRENT TRANSFORMERS (CT) VOLTAGE TRANSFORMERS (VT)
The accuracy class of a current transformer for measuring is The accuracy class of a voltage transformer for
given by a number (class rate) representing the ratio error measuring is given by a number (class rate) representing
limit expressed as a percentage of the rated primary current the ratio error limit expressed as a percentage of the
when the transformer is running at its accuracy load. rated primary voltage when the transformer is running
at its accuracy load.
Accuracy classes for current transformers are: 0.15S; 0.15;
0.15N; 0.3S; 0.3; 0.6 and 1.2. For Accuracy class 0.3, 0.6, Accuracy classes for voltage transformers are: 0.15; 0.3;
0.15N and 1.2 the ratio correction factor must fall within the 0.6 and 1.2.
parallelograms for 100% and 10% respectively. For accuracy
class 0.15, 0.15S and 0.3S the ratio correction factor must The following example calculates the correction factor for
fall within the parallelograms for 100% and 5% respectively. a voltage transformer with the following characteristics:
0.3 accuracy class
The following example calculates the correction factor for 100% rated voltage
a current transformer with the following characteristics:
0.3 accuracy class Ratio correction factor: 1.003
100% rated current

Maximum allowable phase angle: -15.6 minutes
Ratio correction factor: 1.003 Transformer Correction Factor = RCF + (/2600 ) = 1.003
Maximum allowable phase angle: +15.6 minutes + (-15.6/2600) = 0.997
Transformer Correction Factor = RCF (/2600) = 1.003- The ratio correction factor and phase angle for any point
(15.6/2600) = 0.997 inside the 0.3 class parallelogram, will always produce a
TCF between 0.997 and 1.003.
The ratio correction factor and phase angle for any point
inside the 0.3 class parallelogram for 100% rated current 1.006
will always produce a TCF between 0.997 and 1.003.

1.006 0.6 accuracy class
parallelogram
0.15 class- 5%
0.6 class-100% rated current 1.003
rated current 0.3 accuracy class
parallelogram
0.15 class- 100% 1.0015 0.15 accuracy class

0.3 class-100% rated current parallelogram
rated current 1.003
phase angle phase angle
minutes-lagging minutes-leading
0.3 class-10%
rated current 1.0015 0.15S class- 5% and
100% rated current -30 -20 -10 0 +10 +20 +30
phase angle phase angle
minutes-lagging minutes-leading .9985
1.00
-30 -20 -1 0 0 +1 0 +20 +30 .997

to meet 0.3 accuracy class,
the ratio and phase angle
.9985 at the given burden must fall
within this parallelogram
at 100% rated current
.997 and within this
parallelogram at .994
10% rated current
ratio correction factor (RCF)
ratio correction factor (RCF)
.994 Figure 3: VT Equivalent Parallelogram.

Figure 2: CT Equivalent Parallelogram.

ACCURACY STANDARDS
HIGH ACCURACY EXTENDED RANGE CURRENT TRANSFORMERS
Extended range current transformers are designed for were designed to accurately measure down to 10% of the
modern power generation systems. They accurately current rating on the name plate of the transformer.
measure a wider range of current without making physical
changes in the primary or in the secondary connections However, the recent deployment of variable generation
of a current transformer. has created a need to accurately measure a new range of
currents produced by these systems; especially below the
To ensure the best performance on nominal primary rated current of the transformer.
current readings from 1% to Rating factor (please, see
charts below), these current transformers have been Historically, some energy usage revenue went unmeasured.
designed using magnetic materials that minimize Today Arteches high accuracy extended range current
excitation losses and a winding distribution that virtually transformers accurately measure these variable loads.
eliminates stray losses.
Extended range current transformers answer Standard
High accuracy extended range current transformers can CTs problem by expanding the amperage load that can
increase utility revenue through improved metering. This be accurately measured. The wider current range helps to
occurs on systems with variable currents such as wind or reduce the number of different ratios, reducing the amount
solar power generation. In the past, current transformers of inventory needed to respond to customer demands.
Standard Class 0.3 means that from 100% of nominal current through the rating factor, accuracy is guaranteed to
be 0.3%, and from 10% of nominal current through 100% of nominal current accuracy is guaranteed to be 0.6%.
0.6% 0.3%
Rated Current 10% 100% 150% (or Rating Factor)
High Accuracy Class 0.15 means that from 100% of nominal current through the rating factor, accuracy is guaranteed
to be 0.15%, and from 5% of nominal current through 100% of nominal current accuracy is guaranteed to be 0.3%.
0.3% 0.15%
Accuracy Class 0.3S means that from 5% of nominal current through the rating factor, accuracy is guaranteed to
be 0.3%.
0.3%
Accuracy Class 0.15S means that from 5% of nominal current through the rating factor, accuracy is guaranteed to
be 0.15%.
0.15%
High Accuracy, Extended Range Class 0.15 means that from 1% of nominal current through the rating factor,
accuracy is guaranteed to be 0.15%. This goes beyond IEEE C57.13 requirements.
0.15%
Rated Current 1% 5% 100% 150% (or Rating Factor)

OTHER INFORMATION
CURRENT TRANSFORMERS VOLTAGE TRANSFORMERS
Standard burden characteristics @ 60Hz and 5Amps secondary Standard burden @ 60Hz
Burden Resistance Inductance Impedance Volt- Power Secondary Burden

Burden
designation (ohms) (millihenrys) (ohms) Amperes factor Volt- Power
designation
Amperes Factor
METERING BURDENS
W 12.5 0.10
B-0.1 0.09 0.116 0.1 2.5 1.0
X 25.0 0.70
B-0.2 0.18 0.232 0.2 5.0 0.9
M 35.0 0.20
B-05 0.45 0.580 0.5 12.5 0.9
Y 75.0 0.85
B-0.9 0.81 1.040 0.9 22.5 0.9
Z 200.0 0.85
B-1.8 1.62 2.080 1.8 45.0 0.9
ZZ 400.0 0.85
RELAYING BURDENS
As per IEEE C57.13-2016, table 19.
B-1 0.5 2.3 1.0 25 0.5
B-2 1.0 4.6 2.0 50 0.5
B-4 2.0 9.2 4.0 100 0.5
B-8 4.0 18.5 8.0 200 0.5
As per IEEE C57.13-2016, tables 10 and 13.
CROSS REFERENCE OF MOST COMMONLY USED TYPES
INDOOR
Current transformer Voltage transformer
ARTECHE GE ABB KUHLMAN ARTECHE GE ABB KUHLMAN
CID-17 JKM-5,5A KIR-11 CID-17 U/VCE-17 JVM-4,5 VIZ-11 U/VCD-17
OUTDOOR
Current transformer Voltage transformer
ARTECHE GE ABB KUHLMAN ARTECHE GE ABB KUHLMAN
CRB-17 JCK-5 KOR-11 BB-15-972 VRL-17 JVW-3 VOY-60 PTT-110-977
BB-15-971 & URJ-17 JVW-4,5 VOZ-75 PTT-110-9710G

CRE-17 JKW-3,4 KOR-60,75
BB-15-971H VRJ-17 JVW-4,5 VOZ-75 PTT-110-9710
CRE-24 JKW-6 KON-12 BB-25-974 URN-17 JVW-6 VOG-12 PTT-150-9710G
BB-25-973 & VRN-17 JVW-4,5 VOZ-75 PTT-110-9710

CRF-24 JKW-6 KOR-15C
BB-25-973H URN-24 JVW-6 VOY-15G PTT-150-9710G
BB-34-975 & VRN-24 JVW-6 VOY-15 PTT-150-9710

CRF-36 JKW-7 KOR-20
BB-34-976 URS-36 JVW-7 VOY-20G PTT-200-9710G
VRS-36 JVW-7C VOY-20 PTT-200-9710
CE-034-E2 JKW-150,200 KOTD-150,200 LG(X)
URU-52 JVS-250 VOZZ-25G --
CE-046-E2 JKW-250 KOTD-250 CE-046 VRU-52 JVT-250 VOZZ-25 --
CE-069-E2 JKW-350 -- CE-069 URU-72 JVS-350 -- --

OTHER INFORMATION
IT TYPE DESIGNATIONS
ARTECHE Design 1st position 2nd position 3rd position* 4th&5th position
5kV - 36kV
ACA-36 A=0.3 B0.1 up to B0.5
ACD-12, ACD-17, D=0.3 B0.1 up To B0.9
ACD-24 depending on the ratio Insulation class:
A=CT Indoor I=0.3 B0.5 up To B0.9 12=8.7/26/75 kV
ACI-17
transformer Up to 36 kV C=insulation of resin depending on the ratio 17=15/34/110 kV
with DIN standard H=0.3 B0.5 up To B1.8 24=25/50/150 kV
ACH-17, ACH-24 36=34.5/70/200 kV
CTs depending on the ratio
Indoor F=burden B0.5 up To B1.8
ACF-36
depending on the ratio
A=CT Indoor E= indoor & outdoor
G=insulation resin, P=Burden B0.1 up to B1.8 service
AGPE-12 transformer Up to 36 kV
window type C-200
toroidal 12=8.7/26/75 kV
C=CT Indoor up to 34.5 I=insulation and
CID-17 D=0.3 B1.8 C-200
kV only for America molded in resin
VCE-7, VCE-17 Accuracy and burden:
UCE-7, VCE-7 E=0.3WX, 0.3WXY
UXI-12 Insulation class:
C=insulation and 12=8.7/26/75 kV
UCI-17 V=Line To Line
molded in resin. 17=15/34/110 kV
connection
VCL-17, VCL-24 X=insulation and 24=25/50/150 kV
U=line to ground Accuracy and burden:
VTs UXL-17 UXL-24 molded in resin with 36=34.5/70/200 kV
connection I,L,J,N=0.3WXY
Indoor relief valve 52=46/95/250 kV
UCJ-24 72=69/140/350 kV
VCN-36
UXN-36
E=Insulation and
U=line to ground
UEI-24 molded in resin with I=0,3WXY 24=25/50/150 kV
connection
metal coated body
5kV - 72kV
CRB-17 B=0.3B0.5
CRE-17, CRE-24 E=0.3B1.8 T-150 Insulation class:
CRF-24, CRF-36 F=0.3B1.8 T-200 17=15/34/110 kV
C=CT Outdoor up to R=insulation of 24=25/50/150 kV
CRH-36, CRH-52, 69 kV, post type cycloaliphatic resin 36=34.5/70/200 kV
H=0.3B1.8 T-200
CRH-72 52=46/95/250 kV
CTs CRK-36, CRK-52, 72=69/140/350 kV
Outdoor K=0.3B1.8 T-400
CRK-72
CE-034-E2 3rd,4th&5th position 6th position
E=Insulation of
C=CT Outdoor up to 69 Insulation level:
CE-046-E2 cycloaliphatic resin
kV, top-core with metal 034= 34.5/70/200 kV Accuracy and burden
and top-core with
coated head 046= 46/95/250 kV E2=0.3B1.8 T-400
CE-069-E2 metal coated head
069= 69/140/350 kV
VRL-17
URL-17
VRJ-17, VRJ-24
Insulation class:
URJ-17 Accuracy and burden 17= 15/34/110 kV
VRN-17, VRN-24 V=line To Line L,J,N,S=0.3WXY 24=25/50/150 kV
VTs connection R=insulation Of 36=34.5/70/200 kV
URN-17, URN-24
outdoor U=line to ground cycloaliphatic resin
VRS-36 connection
URS-36
VRU-52
52=46/95/250 kV
URU-52 U=0.3WXYZ
72=69/140/350 kV
URU-72
*The letter in the 3rd position is the size of the CT, each letter means a different size, increasing the size in alphabetical order.

600 V
INSTRUMENT
TRANSFORMERS
IRH-1 600 V CURRENT TRANSFORMER
ARTECHE IRH series are dry type indoor/outdoor service current

transformers. The core is encapsulated with epoxy resin which provides
excellent internal dielectric properties and mechanical strength, ensuring
a long mechanical and electrical life. The transformer is maintenance free.
The core is built with high permeability grain oriented silicon steel
laminations for low losses. The windings are copper wire with copper
plate double isolation. The concentric distribution of the coils prevents
magnetic ux leakage, achieving greater accuracy and higher capacity to
withstand mechanical stresses in adverse operating conditions.
INDOOR
IN
NDO
DOORR
60 Hertz
Mechanical characteristics
Insulation Material Color Weight (lbs.)
Resin Brown / Blue Window Type: 5 / Primary Bar Type: 7.3
Window Type:
3.66 (93) 3.15 (80)
See 4 x 5.25 (133)

table
3.40 (86)
6 (152.4)
Drawing number: 4287699

3.40 (86)
Primary Bar Type:

12.13 (308)
6 (152.4)
ONE SECONDARY TERMINALS

PRIMARY TERMINAL
SECONDARY AND SHORT CIRCUIT DEVICE
MARKING H1 H2
(50.8 - 63.5)
(Single CONNEC-
2 - 2.5
Primary TIONS
Ratio) X1 X2
Secondary terminals.
Type: Quick Connector
Type: NEMA2 Material: Brass
Material: Copper Diameter: 1/4
Approximate dimensions in inches (mm).
10 www.arteche.com Instrument Transformers | Reference Guide

Electrical characteristics
Power-Frequency
Current Continuous Continuous Withstand Voltage
Nominal (1 min)
Code Code Ratio Thermal Thermal
Window IEEE Metering Relay Voltage BIL
(Window (Bar (Primary: Current Current
Size Accuracy Accuracy System (kV) Primary & Secondary
type) type) Secondary) Rating Factor Rating Factor
(kV) Secondary Winding
(A) @ 30C @ 55C
(kVrms) (kVrms)
735221040 1.5" 200:5 3.0 2.0 0.3 B0.2 - 0.6 10 4 2.5

735221060 1.5" 300:5 2.0 1.5 0.3 B0.2 - 0.6 10 4 2.5
735221080 2.0" 400:5 2.0 1.5 0.3 B0.2 - 0.6 10 4 2.5
735221120 2.0" 600:5 1.5 1.2 0.3 B0.2 - 0.6 10 4 2.5
735225020 1.22 100:5 4.0 3.0 0.3 B0.2 - 0.6 10 4 2.5
735225040 1.22 200:5 3.0 2.0 0.3 B0.2 - 0.6 10 4 2.5
735225045 1.22 200:5 2.0 1.5 0.3 B0.5 - 0.6 10 4 2.5
735225060 1.22 300:5 2.0 1.5 0.3 B0.5 - 0.6 10 4 2.5
735225080 1.4 400:5 2.0 1.5 0.3 B0.5 - 0.6 10 4 2.5
735225100 1.4 500:5 2.0 1.5 0.3 B0.5 - 0.6 10 4 2.5
735225120 1.4 600:5 2.0 1.5 0.3 B0.5 - 0.6 10 4 2.5
735225160 1.4 800:5 1.5 1.2 0.3 B0.5 - 0.6 10 4 2.5
Additional ratings available upon request.
Notes:
Instrument Transformers | Reference Guide www.arteche.com 11


INDOOR-OUTDOOR
60 Hertz
Resin Blue 8.8
3.22 (81.79) 3.14 (79.76)
3.26 (82.80)
2 (50.8)
7.08 (179.83)
5 (127)

MARKING H1 H2
(Single CONNEC-
Primary TIONS
Ratio) X1 X2
Material: Brass
Diameter: 1/4

Power-Frequency Withstand
Continuous Continuous Voltage
Current Ratio Nominal (1 min)
Thermal Thermal
(Primary: IEEE Metering Relay Voltage
Code Current Current BIL (kV)
Secondary) Accuracy Accuracy System Primary &
Rating Factor Rating Factor @ Secondary
(A) (kV) Secondary
@ 30C 55C Winding (kVrms)
(kVrms)
735261060 300:5 1.2 1.0 0.6B0.1/1.2B0.2 - 0.6 10 4 2.5

735261080 400:5 1.2 1.0 0.6B0.2/1.2B0.5 - 0.6 10 4 2.5
735261100 500:5 1.2 1.0 0.6B0.5 - 0.6 10 4 2.5
735261120 600:5 1.2 1.0 0.3B0.1/0.6B1.0 - 0.6 10 4 2.5
735261160 800:5 1.2 1.0 0.3B0.2/0.6B1.0 C-10 0.6 10 4 2.5
735261200 1000:5 1.2 1.0 0.3B0.5/0.6B2.0 C-10 0.6 10 4 2.5
735261240 1200:5 1.2 1.0 0.3B0.5/0.6B2.0 C-10 0.6 10 4 2.5
Notes:


INDOOR
INDOOR-
INDOOR--
OUTDOOR
UL Recognized Component 60 Hertz
Resin Blue Window Type: 10/12 / Primary Bar Type: 15
Window Type:
3.21 (81.5) 4.59 (116.5)
See
table
8.66 (220)
5 (127)
Primary Bar Type:

3.21 (81.5) 4.59 (116.5)
See
table
9.01 (229)
5 (127)
ONE ONE SECONDARY SECONDARY TERMINALS

PRIMARY TERMINAL
SECONDARY with tap AND SHORT CIRCUIT DEVICE
MARKING H1 H2 H1 H2
2 (51)
(Single CONNEC-
Primary TIONS
Ratio) X1 X2 X1 X2 X3
Type: NEMA2 Material: Brass
Material: Copper Diameter: 1/4

Power-Frequency
Nominal (1 min)
Code Code Ratio Thermal Thermal
Window IEEE Metering Relay Voltage BIL
(Window (Bar (Primary: Current Current
Size Accuracy Accuracy System (kV) Primary & Secondary
type) type) Secondary) Rating Factor Rating Factor
(A) @ 30C @ 55C
(kVrms) (kVrms)
735301010 735305010 2.56" 50:5 4.0 3.0 1.2 B0.1 - 0.6 10 4 2.5
735301020 735305020 2.56" 100:5 4.0 3.0 0.3 B0.1 C-10 0.6 10 4 2.5
735301040 735305040 2.56" 200:5 4.0 3.0 0.3 B0.5 C-30 0.6 10 4 2.5
735301060 735305060 3.15" 300:5 4.0 3.0 0.3 B0.5 C-30 0.6 10 4 2.5
735301080 735305080 3.15" 400:5 4.0 3.0 0.3 B0.5 C-30 0.6 10 4 2.5
735301100 735305100 3.15" 500:5 3.0 2.2 0.3 B0.5 C-30 0.6 10 4 2.5
735301120 735305120 3.15" 600:5 2.0 1.5 0.3 B0.5 C-30 0.6 10 4 2.5
735301160 735305160 3.15" 800:5 2.0 1.5 0.3 B0.5 C-20 0.6 10 4 2.5
735301200 735305200 3.15" 1000:5 2.0 1.5 0.3 B0.5 C-30 0.6 10 4 2.5
735301240 735305240 3.15" 1200:5 1.5 1.2 0.3 B1.8 C-30 0.6 10 4 2.5
735302040 735306040 2.56" 200/400:5 4.0/2.0 3.0/1.5 0.3 B0.2/0.3 B0.5 C-30/C-50 0.6 10 4 2.5
735302060 735306060 3.15" 300/600:5 3.0/2.0 2.2/1.5 0.3 B0.2/0.3 B0.5 C-20/C-40 0.6 10 4 2.5
735302080 735306080 3.15" 400/800:5 2.0/2.0 1.5/1.5 0.3 B0.2/0.3 B0.5 C-10/C-30 0.6 10 4 2.5
High Accuracy Extended Range 5% nominal current to Rating Factor
735307120 735308120 3.15" 600:5 2.0 1.5 0.15S B0.5 - 0.6 10 4 2.5
735300120 735309120 3.15" 600:5 3.0 2.0 0.15S B0.2 - 0.6 10 4 2.5
735307200 735308200 3.15" 1000:5 2.0 1.5 0.15S B0.5 - 0.6 10 4 2.5
Notes:


INDOOR-
UL Recognized Component
OUTDOOR
60 Hertz
Resin Blue Tapered Type: 7.5 / Wide Type: 8.5
Tapered Type: 6.2 (157.5) 3.03 (77)

9.08 (230.6)
4.5 (114)
3.03 (77)
Wide Type:
6.2 (157.5)
9.06 (230)
4.5 (114)

MARKING H1 H2
(Single CONNEC-
Primary TIONS
Ratio) X1 X2
Material: Brass
Diameter: 1/4
Approximate dimensions in inches.

Power-Frequency
Current Withstand Voltage
Continuous Continuous Nominal (1 min)
Code Code Ratio
Thermal Thermal IEEE Metering Relay Voltage BIL
(Tapered (Wide (Primary:
Current Rating Current Rating Accuracy Accuracy System (kV) Primary & Secondary
type) type) Secondary)
Factor @ 30C Factor @ 55C (kV) Secondary Winding
(A)
(kVrms) (kVrms)
735323020 735324020 100:5 4.0 3.0 1.2 B0.1 - 0.6 10 4 2.5

735323040 735324040 200:5 4.0 3.0 0.3 B0.1 C-10 0.6 10 4 2.5
735323060 735324060 300:5 4.0 3.0 0.3 B0.2 C-20 0.6 10 4 2.5
735323080 735324080 400:5 4.0 3.0 0.3 B0.2 C-20 0.6 10 4 2.5
735323100 735324100 500:5 3.0 2.2 0.3 B0.5 C-20 0.6 10 4 2.5
735323120 735324120 600:5 3.0 2.2 0.3 B0.5 C-20 0.6 10 4 2.5
735323160 735324160 800:5 3.0 2.2 0.3 B0.5 C-20 0.6 10 4 2.5
735323200 735324200 1000:5 2.0 1.5 0.3 B0.5 C-30 0.6 10 4 2.5
735323240 735324240 1200:5 2.0 1.5 0.3 B0.9 C-30 0.6 10 4 2.5
735323300 735324300 1500:5 2.0 1.5 0.3 B0.9 C-50 0.6 10 4 2.5
735323400 735324400 2000:5 1.5 1.2 0.3 B1.8 C-20 0.6 10 4 2.5
735323600 735324600 3000:5 1.3 1.0 0.3 B1.8 C-20 0.6 10 4 2.5
735323800 735324800 4000:5 1.0 0.75 0.3 B1.8 C-10 0.6 10 4 2.5
735327100 735328100 500:5 2.0 1.5 0.15S B0.2 - 0.6 10 4 2.5
735327200 735328200 1000:5 2.0 1.5 0.15S B0.5 - 0.6 10 4 2.5
735327400 735328400 2000:5 2.0 1.5 0.15S B0.5 - 0.6 10 4 2.5
Notes:


INDOOR-
OUTDOOR
60 Hertz
Mechanical
cal characteristics
Resin Blue 13
2.62 (66.5)
5.5 (139.7) 6 (152.4)

9 (228.6)
5.25 (133)
6.38 (162)
8.25 (209.5)
7.5 (109.5)
ONE ONE SECONDARY

SECONDARY with tap
MARKING H1 H2 H1 H2
(Single
Primary
SECONDARY TERMINALS
AND SHORT CIRCUIT DEVICE
CONNEC-
TIONS
Material: Brass
Diameter: 1/4

Power-Frequency Withstand
Voltage
Current Ratio Continuous Continuous Nominal (1 min)
Code (Primary: Thermal Current Thermal Current IEEE Metering Relay Voltage BIL
(Window type) Secondary) Rating Factor @ Rating Factor @ Accuracy Accuracy System (kV) Primary & Secondary
(A) 30C 55C (kV) Secondary Winding
(kVrms) (kVrms)
735341080 400:5 3.0 2.2 0.3 B0.2 C-20 0.6 10 4 2.5

735341100 500:5 4.0 3.0 0.3 B0.5 - 0.6 10 4 2.5
735341120 600:5 3.0 2.2 0.3 B0.5 C-30 0.6 10 4 2.5
735341160 800:5 2.0 1.5 0.3 B0.5 C-30 0.6 10 4 2.5
735341200 1000:5 2.0 1.5 0.3 B0.5 C-30 0.6 10 4 2.5
735341240 1200:5 2.0 1.5 0.3 B0.9 C-30 0.6 10 4 2.5
735341300 1500:5 3.0 2.2 0.3 B0.9 C-30 0.6 10 4 2.5
735341400 2000:5 2.0 1.5 0.3 B1.8 C-50 0.6 10 4 2.5
735341600 3000:5 1.5 1.2 0.3 B1.8 C-10 0.6 10 4 2.5
735341800 4000:5 1.33 1.0 0.3 B1.8 - 0.6 10 4 2.5
735342120 600/1200:5 3.0/2.0 2.2/1.5 0.3 B0.2/B0.9 C-10/C-30 0.6 10 4 2.5
735342160 800/1600:5 3.0/2.0 2.2/1.5 0.3 B0.2/B1.8 C-30/C-50 0.6 10 4 2.5
735342200 1000/2000:5 3.0/2.0 2.2/1.5 0.3 B0.5/B1.8 C-30/C-50 0.6 10 4 2.5
735342300 1500/3000:5 2.0/1.5 1.5/1.2 0.3 B0.9/B1.8 --/C-10 0.6 10 4 2.5
735342400 2000/4000:5 2.0/1.33 1.5/1.0 0.3 B1.8/B1.8 -- 0.6 10 4 2.5
735347400 2000:5 2.5 1.8 0.15S B0.9 - 0.6 10 4 2.5
Notes:


INDOOR-
OUTDOOR
60 Hertz
Resin Blue 19
2.62 (66.5)
8.26 (209.8)
11.38 (289)
12.07 (306.5)
5.24 (133)
8.25 (209.5)
9.76 (248)
ONE ONE SECONDARY

SECONDARY with tap
MARKING H1 H2 H1 H2
(Single
Primary
SECONDARY TERMINALS
AND SHORT CIRCUIT DEVICE
CONNEC-
TIONS
Material: Brass
Diameter: 1/4

Power-Frequency
Withstand Voltage
Current Ratio Continuous Continuous Nominal (1 min)
Code
(Primary: Thermal Current Thermal Current IEEE Metering Relay Voltage BIL
(Window
Secondary) Rating Factor @ Rating Factor @ Accuracy Accuracy System (kV) Primary & Secondary
type)
(A) 30C 55C (kV) Secondary Winding
(kVrms) (kVrms)
735361400 2000:5 2.0 1.5 0.3 B0.9 C-50 0.6 10 4 2.5

735361600 3000:5 2.0 1.5 0.3 B1.8 C-100 0.6 10 4 2.5
735361800 4000:5 1.5 1.2 0.3 B1.8 C-100 0.6 10 4 2.5
735361100 5000:5 1.33 1.0 0.3 B1.8 C-100 0.6 10 4 2.5
735361120 6000:5 1.0 0.75 0.3 B1.8 - 0.6 10 4 2.5
735362200 1000/2000:5 3.0/2.0 2.2/1.5 0.3 B0.5/B1.8 C-30/C-50 0.6 10 4 2.5
735362300 1500/3000:5 3.0/2.0 2.2/1.5 0.3 B0.5/B1.8 C-50/C-100 0.6 10 4 2.5
735362400 2000/4000:5 2.0/1.5 1.5/1.2 0.3 B0.9/B1.8 C-50/C-100 0.6 10 4 2.5
735369991 2500/5000:5 2.0/1.33 1.5/1.0 0.3 B1.8/B1.8 C-50/C-100 0.6 10 4 2.5
735369992 3000/6000:5 1.33/1.0 1.0/0.75 0.3 B1.8/B1.8 - 0.6 10 4 2.5
Notes:

ICP-3 600 V CURRENT TRANSFORMER
ARTECHE ICP series are dry type indoor service current transformers.
The core is encapsulated with an impact-resistant polycarbonate which
provides excellent internal dielectric properties and mechanical strength,
ensuring a long mechanical and electrical life. The transformer is
maintenance free.
laminations for low losses.
The windings are copper wire with copper plate double isolation. The
concentric distribution of the coils prevents magnetic ux leakage,
achieving greater accuracy and higher capacity to withstand mechanical
stresses in adverse operating conditions.
INDOOR
60 Hertz
Polycarbonate Black 26
3.54 (90)
9.9 (251.5)
10 (254)
6.5 (165)
8.43 (214)
1.38 (35)
ONE ONE
SECONDARY SECONDARY MULTIRATIO
MARKING H1 H2 H1 H2
(Single
Primary
Ratio) X1 X2 X1 X2 X3 X4 X5

Power-Frequency
Nominal (1 min)
Ratio Thermal Thermal
Window Relay Voltage BIL
Code (Primary: Current Current IEEE Metering Accuracy
Size Accuracy System (kV) Primary & Secondary
Secondary) Rating Factor Rating Factor
(A) @ 30C @ 55C
(kVrms) (kVrms)
735131015 6.50" 75:5 2.0 1.5 2.4B0.2 C10 0.6 10 4 2.5

735131020 6.50" 100:5 2.0 1.5 1.2B0.1/2.4B0.2 C10 0.6 10 4 2.5
735131030 6.50" 150:5 2.0 1.5 0.6B0.1/1.2B0.2/2.4B0.5 C20 0.6 10 4 2.5
735131040 6.50" 200:5 2.0 1.5 0.6B0.2/1.2B0.5 C20 0.6 10 4 2.5
735131050 6.50" 250:5 2.0 1.5 0.6B0.2/1.2B0.5/2.4B0.9 C20 0.6 10 4 2.5
735131060 6.50" 300:5 2.0 1.5 0.3B0.1/0.6B0.2/1.2B0.9/2.4B1.8 C20 0.6 10 4 2.5
735131080 6.50" 400:5 2.0 1.5 0.3B0.2/0.6B0.5/1.2B1.8 C50 0.6 10 4 2.5
735131100 6.50" 500:5 2.0 1.5 0.3B0.5/0.6B0.9/1.2B1.8 C50 0.6 10 4 2.5
735131120 6.50" 600:5 2.0 1.5 0.3B0.5/0.6B1.8 C50 0.6 10 4 2.5
735131160 6.50" 800:5 2.0 1.5 0.3B0.9/0.6B1.8 C100 0.6 10 4 2.5
735131200 6.50" 1000:5 2.0 1.5 0.3B1.8 C100 0.6 10 4 2.5
735131240 6.50" 1200:5 2.0 1.5 0.3B1.8 C200 0.6 10 4 2.5
735131300 6.50" 1500:5 2.0 1.5 0.3B1.8 C200 0.6 10 4 2.5
735131400 6.50" 2000:5 2.0 1.5 0.3B1.8 C200 0.6 10 4 2.5
735131500 6.50" 2500:5 2.0 1.5 0.3B1.8 C200 0.6 10 4 2.5
735131600 6.50" 3000:5 2.0 1.5 0.3B1.8 C200 0.6 10 4 2.5
735131800 6.50" 4000:5 2.0 1.5 0.3B1.8 C200 0.6 10 4 2.5
735132120 6.50" 600:5 MR 2.0 1.5 0.3B0.5/0.6B1.8 C100 0.6 10 4 2.5
735132240 6.50" 1200:5 MR 2.0 1.5 0.3B1.8 C200 0.6 10 4 2.5
735132400 6.50" 2000:5 MR 2.0 1.5 0.3B1.8 C200 0.6 10 4 2.5
735132600 6.50" 3000:5 MR 2.0 1.5 0.3B1.8 C200 0.6 10 4 2.5
735132800 6.50" 4000:5 MR 2.0 1.5 0.3B1.8 C200 0.6 10 4 2.5
Notes:

ARTECHE ICP series are dry type indoor service current transformers.
The core is encapsulated with an impact-resistant polycarbonate which
maintenance free.
laminations for low losses.
The windings are copper wire with copper plate double isolation. The
concentric distribution of the coils prevents magnetic flux leakage,
achieving greater accuracy and higher capacity to withstand mechanical
stresses in adverse operating conditions.
INDOOR
60 Hertz
Polycarbonate Black 54.8
6.93 (176)
6.5 (165)
10 (254)
10 (254)
8.43 (214)
1.38 (35) Drawing number: 4287900
ONE ONE
SECONDARY SECONDARY MULTIRATIO
MARKING H1 H2 H1 H2
(Single
Primary
Ratio) X1 X2 X1 X2 X3 X4 X5

Power-Frequency
Nominal (1 min)
Ratio Thermal Thermal
Window Relay Voltage BIL
Code (Primary: Current Current IEEE Metering Accuracy
Size Accuracy System (kV) Primary & Secondary
Secondary) Rating Factor Rating Factor
(A) @ 30C @ 55C
(kVrms) (kVrms)
735151010 6.50" 50:5 2.0 1.5 1.2B0.1/2.4B0.2 C10 0.6 10 4 2.5

735151015 6.50" 75:5 2.0 1.5 1.2B0.2/2.4B0.5 C20 0.6 10 4 2.5
735151020 6.50" 100:5 2.0 1.5 0.6B0.1/1.2B0.2/2.4B0.5 C20 0.6 10 4 2.5
735151030 6.50" 150:5 2.0 1.5 0.6B0.2/1.2B0.5/2.4B0.9 C50 0.6 10 4 2.5
735151040 6.50" 200:5 2.0 1.5 0.3B0.2/0.6B0.5/1.2B0.9/2.4B1.8 C50 0.6 10 4 2.5
735151050 6.50" 250:5 2.0 1.5 0.3B0.2/0.6B0.5/1.2B0.9/2.4B1.8 C50 0.6 10 4 2.5
735151060 6.50" 300:5 2.0 1.5 0.3B0.5/0.6B0.9/1.2B1.8 C100 0.6 10 4 2.5
735151080 6.50" 400:5 2.0 1.5 0.3B0.5/0.6B1.8 C100 0.6 10 4 2.5
735151100 6.50" 500:5 2.0 1.5 0.3B0.9/0.6B1.8 C100 0.6 10 4 2.5
735151120 6.50" 600:5 2.0 1.5 0.3B0.9/0.6B1.8 C200 0.6 10 4 2.5
735151160 6.50" 800:5 2.0 1.5 0.3B1.8 C200 0.6 10 4 2.5
735151200 6.50" 1000:5 2.0 1.5 0.3B1.8 C200 0.6 10 4 2.5
735151240 6.50" 1200:5 2.0 1.5 0.3B1.8 C400 0.6 10 4 2.5
735151300 6.50" 1500:5 2.0 1.5 0.3B1.8 C400 0.6 10 4 2.5
735151400 6.50" 2000:5 2.0 1.5 0.3B1.8 C400 0.6 10 4 2.5
735151500 6.50" 2500:5 2.0 1.5 0.3B1.8 C400 0.6 10 4 2.5
735151600 6.50" 3000:5 2.0 1.5 0.3B1.8 C400 0.6 10 4 2.5
735151800 6.50" 4000:5 1.33 1.0 0.3B1.8 C400 0.6 10 4 2.5
735159991 6.50" 5000:5 1.0 0.75 0.3B1.8 C400 0.6 10 4 2.5
735159992 6.50" 6000:5 1.0 0.75 0.3B1.8 C400 0.6 10 4 2.5
735152120 6.50" 600:5 MR 2 1.5 0.3B0.9/0.6B1.8 C200 0.6 10 4 2.5
735152240 6.50" 1200:5 MR 2 1.5 0.3B1.8 C400 0.6 10 4 2.5
735152400 6.50" 2000:5 MR 2 1.5 0.3B1.8 C400 0.6 10 4 2.5
735152600 6.50" 3000:5 MR 2 1.5 0.3B1.8 C400 0.6 10 4 2.5
735152800 6.50" 4000:5 MR 1.33 1.0 0.3B1.8 C400 0.6 10 4 2.5
735159993 6.50" 5000:5 MR 1 0.75 0.3B1.8 C400 0.6 10 4 2.5
735159994 6.50" 6000:5 MR 1 0.75 0.3B1.8 C400 0.6 10 4 2.5
Notes:

OVER BUSHING CURRENT
TRANSFORMER 600 V CURRENT TRANSFORMER
The ARTECHE Over Bushing CT series are 600 V rated units designed
to t over a variety of specied bushing sizes. Primary current ratios are
available from 200:5 thru 5000:5 at 60 Hz with a Rating Factor of up to
4.0.
This Slip-Over type CT will operate with high accuracy for metering or
relay applications.
OUTDOOR
60 Hertz
Single, Dual and
Multi Ratios,
Window Type,
Metering/Relaying
The core and coil assembly is wound and tape The core of the CT is constructed from high
wrapped and is available in window sizes from 2.5 permeability grain oriented silicon steel
to 45 inches. The secondary leads are typically laminations which provide low core losses. The
#10 AWG or #12 AWG. The bushing insulation windings are constructed with copper wire
provides the dielectric protection for the CT. and copper plate double isolation. Concentric
distribution of the CT coils prevents magnetic ux
A metal housing covers the whole Current leakage, achieving greater accuracy and higher
Transformer. capacity to withstand mechanical stresses under
adverse operating conditions.
STAINLESS STEEL BODY
GROUND CONNECTION
(0.59)
2 HOLES TO CONDUIT
TERMINALS 1/4
PIPE 1NPT
ALUMINIUM TERMINAL BOX
55
25
8x 1.18x.59
1/2-UNC
13
5
35

OVER BUSHING CURRENT
Accuracy perfomance Testing

The ARTECHE Bushing CT provides 0.3 metering The ARTECHE Bushing CT is individually tested
class accuracy with burdens from B0.1 to B1.8 per the IEEE C57.13 standard, including dielectric
and up to class C800 for relay applications. The tests, accuracy and polarity.
transformer is accurate through its Rating Factor,
and can be used continuously to this level.
Mounting Options
The ARTECHE Bushing CT is designed to be Through careful calculation, steel selection
externally mounted around the bushings of power and testing, existing current transformer
transformers, circuit breakers, underground characteristics can be matched with the ARTECHE
potheads or in switchgear. Bushing CT. Existing characteristic curve would
be required. Contact factory for other needs.
How to order
When ordering an ARTECHE Over Bushing CT,
include the following information:
1. Minimum inside diameter (ID) ___ in [mm]
2. Maximum outside diameter (OD) ___ in [mm]
3. Maximum allowable height (HT) ___ in [mm]
4. Current ratio and taps, if any ___ (:5A or :1A | SR, DR, MR)
5. Accuracy and burden requirements, for example,

Metering - ___ (0.3 B0.1 thru B1.8)
Relaying - ___ (C-100, C-200, C-400, or C-800 or other)
If IEC ratings, list class and burden ___ (e.g., class 0.2-20 VA, 5P20-40 VA)
6. Continuous Rating Factor ___ (standard is RF=2.0)
7. Frequency ___ (standard is 60 Hz)
8. Lead length & type ___, size - ___(standard is #10 AWG TW)
NOTE Due to the many variations of mounting, Arteche does not supply mounting hardware.
Units are custom manufactured to customer specications. Contact factory to discuss other options.
Notes:

BUSHING CURRENT
ARTECHE Bushing CT series are designed to t over a variety of specied

bushing sizes. Primary current ratios are available from 200:5 thru 5000:5
INDOOR at 60 Hz with a Rating Factor up to 4.0. This tape-wound CT will operate
60 Hertz for metering or relaying applications.
Single, Dual and
Multi Ratios,
Window Type,
Metering/Relaying
The core and coil assembly is wound and tape The core of the CT is constructed from high
wrapped and is available in window sizes from 2.5 permeability grain oriented silicon steel laminations
to 45 inches. which provide low core losses. The windings are
constructed with copper wire and copper plate
The secondary leads are typically #10 AWG or double insulated. All secondary windings are
#12 AWG. The bushing insulation provides the fully distributed around the core, which provides
dielectric protection for the CT. Optional TEFZEL low leakage reactance on each ratio, achieving
insulation for the CT is also available. greater accuracy and higher capacity to withstand
mechanical stresses under adverse operating
conditions.
NAME PLATE
2
D
-4
+1

D1
POLARITY MARK D1 D2 A L=inches WEIGHT lbs.
Specs and dimensions available upon request.

L=inches

X1 X2 X3 X4 X5
TYPE OF
CONNECTIONS
(Secondary
terminal)
COPPER WIRE 10-12 AWG FLAT CONNECTION 1/4 COPPER TERMINAL

BUSHING CURRENT
Accuracy perfomance Testing

The ARTECHE Bushing CT provides 0.3 metering The Arteche Bushing CT is individually tested and
class accuracy with burdens from B0.1 to B1.8 certied to IEEE C57.13 or CAN/CSA C60044.
and class C-800 for relaying applications. The
transformer is accurate through its Rating Factor
for continuous operation.
Mounting Features and quality

The ARTECHE Bushing CT is designed to be Customized solutions can be developped to
internally mounted around the bushings of power satisfy specical customer needs.
transformers, circuit breakers and switchgear. Consistent accuracy during the transformers
entire life cycle, providing maximum reliability.
ISO 9001:2008 quality system certicate.
How to order
When ordering an ARTECHE Bushing CT, include
the following information:
1. Minimum inside diameter (D2) ___ in
2. Maximum outside diameter (D1) ___ in
3. Maximum allowable height (A) ___ in
4. Current ratio and taps, if any ___ (:5A or :1A | Single Ratio, Double Ratio or Multi Ratio)
5. Accuracy and burden requirements, for example,

Metering - ___ (0.3 B0.1 thru B1.8 or other)
Relaying - ___ (C-100, C-200, C-400, or C-800 or other)
6. Continuous Rating Factor ___ (standard is RF=2.0)
7. Frequency ___ (standard is 60 Hz)
8. Lead length & type ___, size - ___(standard is #10 AWG)
9. Used in or above oil ___ (Yes/No), or in dry surroundings - ___ (Yes/No)
NOTE Due to the many variations of mounting, Arteche does not supply mounting hardware.
Please, dont hesitate to contact us to discuss other options.
Notes:

5 kV 34.5kV
INDOOR
INSTRUMENT
TRANSFORMERS
UCE-7 5 kV VOLTAGE TRANSFORMER
Unfused Fused
ARTECHE UC/UX/VC series are dry type indoor service voltage
transformers. The core is encapsulated with Type B epoxy resin which
maintenance free.
IINDOOR
ND OR
60 Hertz
ertz Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC
requirements.
Insulation Material Colors Weight (lbs.)
Secondary
Resin Gray* 32 terminals
1/4-UNC
Unfused 3.12 (79.2)
5.83 (144.3)
Nameplate
6.35 (161.3)
5.5 (139.7)
6.6 (167.6)
5.67 (144)
8.5 (215.9)
9.31 (236.5)
Fused
5.68 (144.3) 3.17 (80.5)
Nameplate
6.35 (161.3)
5.5 (139.7)
8.22 (208.8)
6.6 (167.6)
Secondary
5.67 (144)
terminals
1/4-UNC
8.5 (215.9)
9.31 (236.5)
ONE
SECONDARY
MARKING H1 H2
(Single
Primary
Ratio) X1 X2

* Brown color available upon request

Power-Frequency
Continuous Rated Withstand Voltage
Nominal
Rated Voltage Thermal (1 min)
Primary Secondary IEEE Metering Voltage BIL
Code Ratio Voltage Factor Burden
(V) (V) Accuracy System (kV) Primary & Secondary
Factor 30 s (VA)
(Un) (Un)
(kVrms) (kVrms)
Switchgear style (no fuse)

753060020 20:1 2400/4160GY 120 0.3 W,X,M,Y/1.2Z 1.1 1.25 750 5 60 19 2.5
753060035 35:1 4200/4200GY 120 0.3 W,X,M,Y/1.2Z 1.1 1.25 750 5 60 19 2.5
753060040 40:1 4800/4800GY 120 0.3 W,X,M,Y/1.2Z 1.1 1.25 750 5 60 19 2.5
Fuse clips only (no fuse)

753061020 20:1 2400/4160GY 120 0.3 W,X,M,Y/1.2Z 1.1 1.25 750 5 60 19 2.5
753061035 35:1 4200/4200GY 120 0.3 W,X,M,Y/1.2Z 1.1 1.25 750 5 60 19 2.5
753061040 40:1 4800/4800GY 120 0.3 W,X,M,Y/1.2Z 1.1 1.25 750 5 60 19 2.5
Fuse clips and fuse

753062020 20:1 2400/4160GY 120 0.3 W,X,M,Y/1.2Z 1.1 1.25 750 5 60 19 2.5
753062035 35:1 4200/4200GY 120 0.3 W,X,M,Y/1.2Z 1.1 1.25 750 5 60 19 2.5
753062040 40:1 4800/4800GY 120 0.3 W,X,M,Y/1.2Z 1.1 1.25 750 5 60 19 2.5
All units can be supplied either switchgear style, fuse clips only or fuses and clips. Please contact your commercial representant for further information.
Notes:

VCE-7 5 kV VOLTAGE TRANSFORMER
Unfused Fused
maintenance free.
INDOOR
IN R
60 Hertz
tz Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC
requirements.
nent
Resin Gray* 32
Unfused
6.3(160)
5(127)
Nameplate 5.5 (139.7)

6.35 (161.3)
6.13 (155.7)
5.67 (144)
Secondary
terminals
1/4-UNC
8.5 (215.9)
9.31 (236.5)
Fused
6.3(160)
5.68 (144.3)
5(127)
Nameplate
5.5 (139.7)
6.35 (161.3)
7.26 (184.4)
6.13 (155.7)
Secondary
terminals
5.67 (144)
1/4-UNC
8.5 (215.9)
9.31 (236.5)
ONE
SECONDARY
MARKING H1 H2
(Single
Primary
Ratio) X1 X2


Power-Frequency
Nominal
Primary Secondary IEEE Metering Voltage BIL
Code Ratio Voltage Factor Burden
(V) (V) Accuracy System (kV) Primary & Secondary
Factor 30 s (VA)
(Un) (Un)
(kVrms) (kVrms)

753030020 20:1 2400/4160Y 120 0.3 W,X,M,Y/1.2Z 1.1 1.25 750 5 60 19 2.5
753030035 35:1 4200/4200Y 120 0.3 W,X,M,Y/1.2Z 1.1 1.25 750 5 60 19 2.5
753030040 40:1 4800/4800Y 120 0.3 W,X,M,Y/1.2Z 1.1 1.25 750 5 60 19 2.5

753031020 20:1 2400/4160Y 120 0.3 W,X,M,Y/1.2Z 1.1 1.25 750 5 60 19 2.5
753031035 35:1 4200/4200Y 120 0.3 W,X,M,Y/1.2Z 1.1 1.25 750 5 60 19 2.5
753031040 40:1 4800/4800Y 120 0.3 W,X,M,Y/1.2Z 1.1 1.25 750 5 60 19 2.5
Fuse clips and fuse

753032020 20:1 2400/4160Y 120 0.3 W,X,M,Y/1.2Z 1.1 1.25 750 5 60 19 2.5
753032035 35:1 4200/4200Y 120 0.3 W,X,M,Y/1.2Z 1.1 1.25 750 5 60 19 2.5
753032040 40:1 4800/4800Y 120 0.3 W,X,M,Y/1.2Z 1.1 1.25 750 5 60 19 2.5
All units can be supplied either switchgear style, fuse clips only or fuses and clips. Please contact your commercial representant for further information.
Notes:

UXI-12 8.7 kV VOLTAGE TRANSFORMER

maintenance free.
INDOOR laminations for low losses. The windings are copper wire with copper
60 Hertz plate double isolation. The concentric distribution of the coils prevents
Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC

requirements.
Resin Gray* 60
10.82 (275) 5.82 (148) 4.92 (125)
10.6 (270.5)
8.07 (205)
8.85 (225)
H1
Sealable
cover
Secondary
terminals
ONE
SECONDARY
MARKING H1 H2
(Single
Primary
Ratio) X1 X2


UXI-12 8.7 kV VOLTAGE TRANSFORMER
Power-Frequency
Nominal
IEEE Rated Voltage Thermal (1 min)
Primary Secondary Voltage BIL
Code Ratio Metering Voltage Factor Burden
(V) (V) System (kV) Primary & Secondary
Accuracy Factor 30 s (VA)
(Un) (Un)
(kVrms) (kVrms)
753221020 20:1 2400/4160GY 120 0.6 W,X,M,Y 1.1 1.5 450 8.7 75 26 2.5
753221035 35:1 4200/7200GY 120 0.6 W,X 1.1 1.5 450 8.7 75 26 2.5
753221040 40:1 4800/8320GY 120 0.6 W,X 1.1 1.5 450 8.7 75 26 2.5
753221060 60:1 7200/12470GY 120 0.6 W,X 1.1 1.5 450 8.7 75 26 2.5
Notes:


maintenance free.
laminations for low losses. The windings are copper wire with copper plate
double isolation. The concentric distribution of the coils prevents magnetic
INDOOR ux leakage, achieving greater accuracy and higher capacity to withstand
mechanical stresses in adverse operating conditions.
60 Hertz
requirements.
Resin Gray* 85
Unfused
9.01 (228.8) 7.48 (189.9)
Nameplate
9.25 (234.95)
9.83 (249.7)
Secondary
terminals
10.25 (260.35)
Fused 9 (228.6)
15.62 (396.75)
Nameplate
8 (203.2)
12.36 (314)
Secondary
terminals
10.25 (260.35)
ONE
SECONDARY
MARKING H1 H2
(Single
Primary
Ratio) X1 X2


Power-Frequency
Nominal
Secon- Rated Voltage Thermal (1 min)
Primary IEEE Metering Voltage BIL
Code Ratio dary Voltage Factor Burden
(V) Accuracy System (kV) Primary & Secondary
(V) Factor 30 s (VA)
(Un) (Un)
(kVrms) (kVrms)

753460060 60:1 7200/12470GY 120 0.3 W,X,M,Y,Z/1.2ZZ 1.1 1.25 1500 15 110 34 2.5
753460070 70:1 8400/14460GY 120 0.3 W,X,M,Y,Z/1.2ZZ 1.1 1.25 1500 15 110 34 2.5
753460100 100:1 12000/12000GY 120 0.3 W,X,M,Y,Z/1.2ZZ 1.1 1.25 1500 15 110 34 2.5
753460110 110:1 13200/13200GY 120 0.3 W,X,M,Y,Z/1.2ZZ 1.1 1.25 1500 15 110 34 2.5
753460120 120:1 14400/14400GY 120 0.3 W,X,M,Y,Z/1.2ZZ 1.1 1.25 1500 15 110 34 2.5

753461060 60:1 7200/12470GY 120 0.3 W,X,M,Y,Z/1.2ZZ 1.1 1.25 1500 15 110 34 2.5
753461070 70:1 8400/14460GY 120 0.3 W,X,M,Y,Z/1.2ZZ 1.1 1.25 1500 15 110 34 2.5
753461100 100:1 12000/12000GY 120 0.3 W,X,M,Y,Z/1.2ZZ 1.1 1.25 1500 15 110 34 2.5
753461110 110:1 13200/13200GY 120 0.3 W,X,M,Y,Z/1.2ZZ 1.1 1.25 1500 15 110 34 2.5
753461120 120:1 14400/14400GY 120 0.3 W,X,M,Y,Z/1.2ZZ 1.1 1.25 1500 15 110 34 2.5
Fuse clips and fuse

753462060 60:1 7200/12470GY 120 0.3 W,X,M,Y,Z/1.2ZZ 1.1 1.25 1500 15 110 34 2.5
753462070 70:1 8400/14460GY 120 0.3 W,X,M,Y,Z/1.2ZZ 1.1 1.25 1500 15 110 34 2.5
753462100 100:1 12000/12000GY 120 0.3 W,X,M,Y,Z/1.2ZZ 1.1 1.25 1500 15 110 34 2.5
753462110 110:1 13200/13200GY 120 0.3 W,X,M,Y,Z/1.2ZZ 1.1 1.25 1500 15 110 34 2.5
753462120 120:1 14400/14400GY 120 0.3 W,X,M,Y,Z/1.2ZZ 1.1 1.25 1500 15 110 34 2.5
All Units can be supplied either switchgear style, fuse clips only or fuses and clips. Please contact your commercial representant for further information.
Notes:

UCI-17 15 kV VOLTAGE TRANSFORMER

maintenance free.
INDOOR laminations for low losses. The windings are copper wire with copper plate
60 Hertz double isolation. The concentric distribution of the coils prevents magnetic
ux leakage, achieving greater accuracy and higher capacity to withstand

requirements.
Resin Gray* 60
10.82 (275) 5.82 (148) 4.9 (125)
10.62 (270)
8.07 (205)
8.85 (225)
Sealable
cover Ground Secondary
connection terminals
ONE
SECONDARY
MARKING H1 H2
(Single
Primary
Ratio) X1 X2


UCI-17 15 kV VOLTAGE TRANSFORMER
Power-Frequency
Nominal
Secon- IEEE Rated Voltage Thermal (1 min)
Primary Voltage BIL
Code Ratio dary Metering Voltage Factor Burden
(V) System (kV) Primary & Secondary
(V) Accuracy Factor 30 s (VA)
(Un) (Un)
(kVrms) (kVrms)
753381060 60:1 7200/12470GY 120 0.3 W,X,M,Y 1.1 1.25 450 15 110 34 2.5
753381063 63.5:1 7620/13200GY 120 0.6 W,X,M,Y 1.1 1.25 450 15 110 34 2.5
753381070 70:1 8400/14550GY 120 0.6 W,X,M,Y 1.1 1.25 450 15 110 34 2.5
Notes:

UXL-17 15 kV VOLTAGE TRANSFORMER

maintenance free.

requirements.
Resin Gray* 60
11.81 (300) 7.28 (185)

5.9 (150)
11.41 (290)
H1
11.22 (285)
Sealable
cover Secondary
terminals
Ground
connection
ONE
SECONDARY
MARKING H1 H2
(Single
Primary
Ratio) X1 X2


Power-Frequency
Nominal
(Un) (Un)
(kVrms) (kVrms)
753441060 60:1 7200/12470GY 120 0.3 W,X,M,Y 1.1 1.5 500 15 110 34 2.5
753441063 63.5:1 7620/13200GY 120 0.3 W,X,M,Y 1.1 1.5 500 15 110 34 2.5
753441070 70:1 8400/14550GY 120 0.3 W,X,M,Y 1.1 1.5 500 15 110 34 2.5
Notes:


maintenance free.
INDOOR mechanical stresses in adverse operating conditions.
60 Hertz
requirements.
Insulation Material Colors Weight (lbs.) 15.31 (389)
Resin Gray* 85
9.25 (235)
Unfused
9.01 (228.85)
Nameplate
9.83 (249.68)
8 (203.2)
13.13 (333.5)
Secondary terminals Drawing number: 4287539
15.31 (389)
Fused
9.25 (235)
9.78 (248.4)
Nameplate
11.57 (294)
8 (203.2)
Secondary terminals 10.25 (260.35)
ONE
SECONDARY
MARKING H1 H2
(Single
Primary
Ratio) X1 X2


Power-Frequency
Nominal
Secon- Rated Voltage Thermal (1 min)
Primary IEEE Metering Voltage BIL
Code Ratio dary Voltage Factor Burden
(V) Accuracy System (kV) Primary & Secondary
(V) Factor 30 s (VA)
(Un) (Un)
(kVrms) (kVrms)

753450060 60:1 7200/12470Y 120 0.3 W,X,M,Y,Z/1.2ZZ 1.1 1.25 1500 15 110 34 2.5
753450070 70:1 8400/14460Y 120 0.3 W,X,M,Y,Z/1.2ZZ 1.1 1.25 1500 15 110 34 2.5
753450100 100:1 12000/12000Y 120 0.3 W,X,M,Y,Z/1.2ZZ 1.1 1.25 1500 15 110 34 2.5
753450110 110:1 13200/13200Y 120 0.3 W,X,M,Y,Z/1.2ZZ 1.1 1.25 1500 15 110 34 2.5
753450120 120:1 14400/14400Y 120 0.3 W,X,M,Y,Z/1.2ZZ 1.1 1.25 1500 15 110 34 2.5

753451060 60:1 7200/12470Y 120 0.3 W,X,M,Y,Z/1.2ZZ 1.1 1.25 1500 15 110 34 2.5
753451070 70:1 8400/14460Y 120 0.3 W,X,M,Y,Z/1.2ZZ 1.1 1.25 1500 15 110 34 2.5
753451100 100:1 12000/12000Y 120 0.3 W,X,M,Y,Z/1.2ZZ 1.1 1.25 1500 15 110 34 2.5
753451110 110:1 13200/13200Y 120 0.3 W,X,M,Y,Z/1.2ZZ 1.1 1.25 1500 15 110 34 2.5
753451120 120:1 14400/14400Y 120 0.3 W,X,M,Y,Z/1.2ZZ 1.1 1.25 1500 15 110 34 2.5
Fuse clips and fuse

753452060 60:1 7200/12470Y 120 0.3 W,X,M,Y,Z/1.2ZZ 1.1 1.25 1500 15 110 34 2.5
753452070 70:1 8400/14460Y 120 0.3 W,X,M,Y,Z/1.2ZZ 1.1 1.25 1500 15 110 34 2.5
753452100 100:1 12000/12000Y 120 0.3 W,X,M,Y,Z/1.2ZZ 1.1 1.25 1500 15 110 34 2.5
753452110 110:1 13200/13200Y 120 0.3 W,X,M,Y,Z/1.2ZZ 1.1 1.25 1500 15 110 34 2.5
753452120 120:1 14400/14400Y 120 0.3 W,X,M,Y,Z/1.2ZZ 1.1 1.25 1500 15 110 34 2.5
All Units can be supplied either switchgear style, fuse clips only or fuses and clips. Please contact your commercial representant for further information.
Notes:

VCL-17 15 kV VOLTAGE TRANSFORMER

maintenance free.

requirements.
Resin Gray* 62
11.8 (300) 7.28 (185)

5.9 (150)
H1
11.41 (290)
10.82 (275)
Sealable H2
cover
ONE
SECONDARY
MARKING H1 H2
(Single
Primary
Ratio) X1 X2


Power-Frequency
Nominal
(Un) (Un)
(kVrms) (kVrms)
753501060 60:1 7200/12470Y 120 0.3 W,X,M,Y 1.1 1.25 600 15 110 34 2.5
753501063 63.5:1 7620/13200Y 120 0.3 W,X,M,Y 1.1 1.25 600 15 110 34 2.5
753501070 70:1 8400/14450Y 120 0.3 W,X,M,Y 1.1 1.25 600 15 110 34 2.5
753501100 100:1 12000/12000Y 120 0.3 W,X,M,Y 1.1 1.25 600 15 110 34 2.5
753501110 110:1 13200/13200Y 120 0.3 W,X,M,Y 1.1 1.25 600 15 110 34 2.5
753501120 120:1 14400/14400Y 120 0.3 W,X,M,Y 1.1 1.25 600 15 110 34 2.5
Notes:


maintenance free.

requirements.
Resin Gray* 60
11.81 (300) 7.28 (185)

5.9 (150)
11.4 (290)
11.22 (285)
H1
Sealable
cover Secondary
terminals
Ground
connection
ONE
SECONDARY
MARKING H1 H2
(Single
Primary
Ratio) X1 X2


Power-Frequency
Nominal
Primary Voltage BIL
(Un) (Un)
(kVrms) (kVrms)
753741100 100:1 12000/20750GY 120 0.3 W,X,M,Y 1.1 1.5 600 25 125 50 2.5
753741120 120:1 14400/24940GY 120 0.3 W,X,M,Y 1.1 1.5 600 25 125 50 2.5
753741200 200:1 24000/24000GY 120 0.3 W,X,M,Y 1.1 1.5 600 25 125 50 2.5
Notes:

UCJ-24 25 kV VOLTAGE TRANSFORMER

maintenance free.

requirements.
Resin Gray* 66
7 (178)
12.79 (325) 5.9 (150)
11 (279)
10.82 (275)
H1
Sealable
cover Secondary
M8 terminals
ONE
SECONDARY
MARKING H1 H2
(Single
Primary
Ratio) X1 X2


UCJ-24 25 kV VOLTAGE TRANSFORMER
Power-Frequency
Nominal
Marked Primary Voltage BIL
Code dary Metering Voltage Factor Burden
Ratio (V) System (kV) Primary & Secondary
(Un) (Un)
(kVrms) (kVrms)
753541100 100:1 12000/20750GY 120 0.3 W,X,M,Y 1.1 1.5 750 25 125 50 2.5
753541120 120:1 14400/24940GY 120 0.3 W,X,M,Y 1.1 1.5 750 25 125 50 2.5
753541200 200:1 24000/24000GY 120 0.3 W,X,M,Y 1.1 1.5 750 25 125 50 2.5
Notes:

UEI-24 25 kV VOLTAGE TRANSFORMER
ARTECHE UE series are dry type indoor service voltage transformers. The
core is encapsulated with Type B epoxy resin which provides excellent
internal dielectric properties and mechanical strength, ensuring a long
mechanical and electrical life. The transformer is maintenance free.
The entire surface of the transformer is coated with a conductive layer that
is intended to be solidly grounded when energized. This allows for compact
INDOOR mounting inside switchgear or enclosures.
60 Hertz

requirements.
Resin Gray 62
10.82 (275) 5.82 (148)
4.92 (125)
10.8 (274)
11.98 (304)
H1
Sealable
cover Secondary
terminals
ONE
SECONDARY
MARKING H1 H2
(Single
Primary
Ratio) X1 X2

UEI-24 25 kV VOLTAGE TRANSFORMER
Power-Frequency
Nominal
(Un) (Un)
(kVrms) (kVrms)
753681100 100:1 12000/20780GY 120 0.6 W,X,M 1.1 1.25 350 25 125 50 2.5
753681120 120:1 14400/24940GY 120 0.6 W,X,M 1.1 1.25 350 25 125 50 2.5
Notes:


maintenance free.

requirements.
Resin Gray* 62
11.81 (300) 7.28 (185)

5.61 (142.5)
H1
9.92 (252)
10.86 (276)
Terminal
secondary
Ground
H2
connection
X1 X2
ONE
SECONDARY
MARKING H1 H2
(Single
Primary
Ratio) X1 X2


Power-Frequency
Nominal
(Un) (Un)
(kVrms) (kVrms)
753801100 100:1 12000/20750Y 120 0.3 W,X,M,Y 1.1 1.25 600 25 125 50 2.5
753801120 120:1 14400/24940Y 120 0.3 W,X,M,Y 1.1 1.25 600 25 125 50 2.5
753801200 200:1 24000/24000Y 120 0.3 W,X,M,Y 1.1 1.25 600 25 125 50 2.5
Notes:

UXN-36 34.5 kV VOLTAGE TRANSFORMER

maintenance free.

requirements.
Resin Gray* 97
7.87 (200)
14.76 (375) 8.74 (222)
13.77 (350)
13.77 (350)
H1
Sealable
cover Secondary
terminals
ONE
SECONDARY
MARKING H1 H2
(Single
Primary
Ratio) X1 X2


UXN-36 34.5 kV VOLTAGE TRANSFORMER
Power-Frequency
Nominal
(Un) (Un)
(kVrms) (kVrms)
754391175 175:1 20125/34500GY 115 0.3 W,X,M,Y 1.1 1.5 750 34.5 200 70 2.5
Notes:

UCS-36 34.5 kV VOLTAGE TRANSFORMER
Unfused Fused
maintenance free.
INDOOR
IN
NDOOR Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC
60
6 0H
Hertz
rtz requirements.
Resin Gray* 167
Unfused
16.14 (410) 9.45 (240) 7.87 (200)
14.44 (367)
13.46 (341.8)
11.8 (230)
Secondary A
Sealable terminals
cover
Fused
9.45 (240)
16.14 (410) 8.75 (222)
18 (457)
14.44 (367)
12.8 (325)
Sealable Secondary A
cover terminals

28.05 (712)
ONE
SECONDARY
MARKING H1 H2
(Single
Primary
Ratio) X1 X2


UCS-36 34.5 kV VOLTAGE TRANSFORMER
Power-Frequency
Nominal
Primary Voltage BIL
(Un) (Un)
(kVrms) (kVrms)
UNFUSED
754260175 175:1 20125/34500GY 115 0.3 W,X,M,Y,Z 1.1 1.5 1500 34.5 200 70 2.5
754260300 300:1 34500/34500GY 115 0.3 W,X,M,Y,Z 1.1 1.5 1500 34.5 200 70 2.5
754260289 289:1 19942/34500GY 69 0.3 W,X,M,Y 1.1 1.5 1500 34.5 200 70 2.5
754260240 240:1 16100/27900GY 67.08 0.3 W,X,M,Y 1.1 1.5 1500 34.5 200 70 2.5
FUSED
754262175 175:1 20125/34500GY 115 0.3 W,X,M,Y,Z 1.1 1.5 1500 34.5 200 70 2.5
754262300 300:1 34500/34500GY 115 0.3 W,X,M,Y,Z 1.1 1.5 1500 34.5 200 70 2.5
754262200 200:1 24000/24000GY 120 0.3 W,X,M,Y,Z 1.1 1.5 1500 34.5 200 70 2.5
754262208 208.33:1 25000/25000GY 120 0.3 W,X,M,Y,Z 1.1 1.5 1500 34.5 200 70 2.5
754262220 220:1 26400/26400GY 120 0.3 W,X,M,Y,Z 1.1 1.5 1500 34.5 200 70 2.5
754262207 207.5:1 24900/24900GY 120 0.3 W,X,M,Y,Z 1.1 1.5 1500 34.5 200 70 2.5
754262240 240:1 27600/27600GY 115 0.3 W,X,M,Y,Z 1.1 1.5 1500 34.5 200 70 2.5
Notes:

VCN-36 34.5 kV VOLTAGE TRANSFORMER

maintenance free.

requirements.
Resin Gray* 99
14.76 (375) 8.74 (222)
7.87 (200)
H1
13.77 (350)
13.36 (415.5)
Terminal
secondary
H2
Sealable
Ground cover
connection
ONE
SECONDARY
MARKING H1 H2
(Single
Primary
Ratio) X1 X2


VCN-36 34.5 kV VOLTAGE TRANSFORMER
Power-Frequency
Nominal
(Un) (Un)
(kVrms) (kVrms)
754421300 300:1 34500/34500Y 120 0.3 W,X,M,Y 1.1 1.5 751 34.5 200 70 2.5
Notes:

VCS-36 34.5 kV VOLTAGE TRANSFORMER
Unfused Fused
maintenance free.
IN OOR
INDOOR
OR Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC
60 Hertz
tz requirements.
Resin Gray* 174
Unfused
16.14 (410)
A
13.46 (341.8)
14.44 (366.7)
7.87 (200)
B
15.94 (405)
Secondary
terminals 11.8 (230)
Sealable cover
Fused
16.14 (410)
16.53 (420)
17.63 (448)
8.75 (222)
15.94 (405) 12.8 (325)

Sealable cover Secondary 28.04 (712)
terminals
ONE
SECONDARY
MARKING H1 H2
(Single
Primary
Ratio) X1 X2


VCS-36 34.5 kV VOLTAGE TRANSFORMER
Power-Frequency
Nominal
(Un) (Un)
(kVrms) (kVrms)
UNFUSED
754610175 175:1 20125/34500Y 115 0.3 W,X,M,Y,Z 1.1 1.5 1500 34.5 200 70 2.5
754610240 240:1 27600/27600Y 115 0.3 W,X,M,Y,Z 1.1 1.5 1500 34.5 200 70 2.5
754610300 300:1 34500/34500Y 115 0.3 W,X,M,Y,Z 1.1 1.5 1500 34.5 200 70 2.5
FUSED
754612175 175:1 20125/34500Y 115 0.3 W,X,M,Y,Z 1.1 1.5 1500 34.5 200 70 2.5
754612240 240:1 27600/27600Y 115 0.3 W,X,M,Y,Z 1.1 1.5 1500 34.5 200 70 2.5
754612300 300:1 34500/34500Y 115 0.3 W,X,M,Y,Z 1.1 1.5 1500 34.5 200 70 2.5
Notes:

CID-7 5 kV CURRENT TRANSFORMER
ARTECHE AC/CID Series are dry type indoor service current transformers.
The core is encapsulated with Type B epoxy resin which provides
INDOOR laminations for low losses. The windings are copper wire with copper
60 Hertz plate double isolation. The concentric distribution of the coils prevents
Partial discharge measurements exceed IEEE C57.13 2008 requirements.
Resin Gray * 38
15 (381)
6.13 (156)
7.07 (180)
5.75 (146)
9.62 (244)
5.51 (140)
(2 x 108)
2 x 4.25
2 x 5 (2 x 127)
ONE
SECONDARY
MARKING H1 H2
(Single
Primary
Ratio) X1 X2


Power-Frequency
Continuous Withstand Voltage
Current Short- Short- Highest
Thermal (1 min)
Ratio time time IEEE Nominal
Current Relay BIL
Code (Primary: Thermal Mechanical Metering Voltage
Rating Accuracy (kV) Primary & Secondary
Secondary) Current Current Accuracy System
Factor @ Secondary Winding
(A) (kA/1s) (kApeak) (kV)
30C (kVrms) (kVrms)
750951001 5:5 1.5 0.5 1.35 0.3 B1.8 T-100 5 60 19 2.5

750951002 10:5 1.5 1 2.7 0.3 B1.8 T-100 5 60 19 2.5
750951003 15:5 1.5 1.5 4.05 0.3 B1.8 T-100 5 60 19 2.5
750951004 20:5 1.5 2 5.4 0.3 B1.8 T-100 5 60 19 2.5
750951005 25:5 1.5 2.5 6.75 0.3 B1.8 T-100 5 60 19 2.5
750951006 30:5 1.5 3 8.1 0.3 B1.8 T-100 5 60 19 2.5
750951008 40:5 1.5 4 10.8 0.3 B1.8 T-100 5 60 19 2.5
750951010 50:5 1.5 5 13.5 0.3 B1.8 T-100 5 60 19 2.5
750951015 75:5 1.5 7.5 20.25 0.3 B1.8 T-100 5 60 19 2.5
750951020 100:5 1.5 10 27 0.3 B1.8 T-100 5 60 19 2.5
750951030 150:5 1.5 15 40.5 0.3 B1.8 T-100 5 60 19 2.5
750951040 200:5 1.5 20 54 0.3 B1.8 T-100 5 60 19 2.5
750951060 300:5 1.5 30 81 0.3 B1.8 T-100 5 60 19 2.5
750951080 400:5 1.5 40 108 0.3 B1.8 T-100 5 60 19 2.5
750951120 600:5 1.5 60 162 0.3 B1.8 T-100 5 60 19 2.5
750951160 800:5 1.5 80 216 0.3 B1.8 T-100 5 60 19 2.5
750951200 1000:5 1.5 100 270 0.3 B1.8 T-100 5 60 19 2.5
750951240 1200:5 1.5 120 324 0.3 B1.8 T-100 5 60 19 2.5
Notes:

ACD-12 8.7 kV CURRENT TRANSFORMER
ARTECHE AC series are dry insulated indoor service current transformers.

The CT core is encapsulated with Type B epoxy resin resulting in excellent
internal dielectric properties and mechanical strength. The device is
maintenance free, providing a long mechanical and electrical service life.
The core of the CT is constructed from silicon steel laminations with

a high permeability grain orientation resulting in low core losses. The
INDOOR windings are copper wire with copper plate double isolation. Concentric
60 Hertz distribution of the CT coils prevents magnetic ux leakage, achieving
greater accuracy and higher capacity to withstand mechanical stresses
under adverse operating conditions.

requirements.
Resin Gray* 35.3
9.37 (238)
6.69 (170) 7.08 (180) 5.1 (130)
H2
5.5 (140)
10.03 (255)
H1
Sealable Secondary
cover terminals
ONE
SECONDARY
MARKING H1 H2
(Single
Primary
Ratio) X1 X2


ACD-12 8.7 kV CURRENT TRANSFORMER
Power-Frequency
Current Short- Short-
Thermal Nominal (1 min)
Ratio time time
Current IEEE Metering Relay Voltage BIL
Code (Primary: Thermal Mechanical
Rating Accuracy Accuracy System (kV) Primary & Secondary
Secondary) Current Current
Factor @ (kV) Secondary Winding
(A) (kA/1s) (kApeak)
30C (kVrms) (kVrms)
750251001 5:5 1.5 0.5 1 0.3 B-0.5 C-50 8.7 75 26 2.5

750251002 10:5 1.5 1 2 0.3 B-0.5 C-50 8.7 75 26 2.5
750251003 15:5 1.5 1.5 3 0.3 B-0.5 C-50 8.7 75 26 2.5
750251004 20:5 1.5 2 4 0.3 B-0.5 C-50 8.7 75 26 2.5
750251005 25:5 1.5 2.5 5 0.3 B-0.5 C-50 8.7 75 26 2.5
750251006 30:5 1.5 3 6 0.3 B-0.5 C-50 8.7 75 26 2.5
750251008 40:5 1.5 4 8 0.3 B-0.5 C-50 8.7 75 26 2.5
750251010 50:5 1.5 5 10 0.3 B-0.5 C-50 8.7 75 26 2.5
750251015 75:5 1.5 7.5 15 0.3 B-0.5 C-50 8.7 75 26 2.5
750251020 100:5 1.5 10 20 0.3 B-0.5 C-50 8.7 75 26 2.5
750251030 150:5 1.5 15 30 0.3 B-0.5 C-50 8.7 75 26 2.5
750251040 200:5 1.5 20 40 0.3 B-0.5 C-50 8.7 75 26 2.5
750251060 300:5 1.5 30 60 0.3 B-0.5 C-50 8.7 75 26 2.5
750251080 400:5 1.5 40 80 0.3 B-0.5 C-50 8.7 75 26 2.5
750251120 600:5 1.5 50 95 0.3 B-0.5 C-50 8.7 75 26 2.5
750251160 800:5 1.5 60 120 0.3 B-0.5 C-50 8.7 75 26 2.5
750251200 1000:5 1.2 75 135 0.3 B-0.5 C-50 8.7 75 26 2.5
750251240 1200:5 1.2 84 150 0.3 B-0.5 C-50 8.7 75 26 2.5
Notes:

AGPE-12 8.7 kV CURRENT TRANSFORMER
ARTECHE AG Series are dry type indoor service current transformers. The
INDOOR plate double isolation. The concentric distribution of the coils prevents
60 Hertz magnetic ux leakage, achieving greater accuracy and higher capacity to

requirements.
Resin Gray* 165.3
11.41 (290) Potential Screw M5 14.56 (370) Nameplate
10.63 (270)
7.99 (203)
Terminal
13.18 (335)
Secondary
Box
Ground
connector
5.11 (130)
ONE TWO
SECONDARY SECONDARIES
MARKING H1 H2 H1 H2
(Single
Primary
Ratio) X1 X2 X1 X2
Y1 Y2


AGPE-12 8.7 kV CURRENT TRANSFORMER
Power-Frequency
Ratio time time
30C (kVrms) (kVrms)
750231400 2000:5 1.2 63 163.8 0.3 B-1.8 8.7 75 26 2.5

750232400 2000:5 1.2 63 163.8 C-400 8.7 75 26 2.5
750231600 3000:5 1.2 63 163.8 0.3 B-1.8 8.7 75 26 2.5
750232600 3000:5 1.2 63 163.8 C-400 8.7 75 26 2.5
750233400 2000:5 1.2 63 163.8 0.3 B-1.8 C-400 8.7 75 26 2.5
750233600 3000:5 1.2 63 163.8 0.3 B-1.8 C-400 8.7 75 26 2.5
C-200,
750234400 2000:5 1.2 63 163.8 0.3 B-1.8 8.7 75 26 2.5
C-200
C-200,
750234600 3000:5 1.2 63 163.8 0.3 B-1.8 8.7 75 26 2.5
C-200
Notes:

ACD-17 15 kV CURRENT TRANSFORMER

requirements.
Resin Gray* 35.3
9.37 (238)
6.69 (170) 7.08 (180) 5.1 (130)
H2
5.5 (140)
10.03 (255)
H1
Sealable
cover
Secondary
terminals M6
ONE
SECONDARY
MARKING H1 H2
(Single
Primary
Ratio) X1 X2


Power-Frequency
Ratio time time
30C (kVrms) (kVrms)
750491001 5:5 1.2 0.5 1 0.3 B-0.5 C-50 15 110 34 2.5

750491002 10:5 1.2 1 2 0.3 B-0.5 C-50 15 110 34 2.5
750491003 15:5 1.2 1.5 3 0.3 B-0.5 C-50 15 110 34 2.5
750491004 20:5 1.2 2 4 0.3 B-0.5 C-50 15 110 34 2.5
750491005 25:5 1.2 2.5 5 0.3 B-0.5 C-50 15 110 34 2.5
750491006 30:5 1.2 3 6 0.3 B-0.5 C-50 15 110 34 2.5
750491008 40:5 1.2 4 8 0.3 B-0.5 C-50 15 110 34 2.5
750491010 50:5 1.2 5 10 0.3 B-0.5 C-50 15 110 34 2.5
750491015 75:5 1.2 7.5 15 0.3 B-0.5 C-50 15 110 34 2.5
750491020 100:5 1.2 10 20 0.3 B-0.5 C-50 15 110 34 2.5
750491030 150:5 1.2 15 30 0.3 B-0.5 C-50 15 110 34 2.5
750491040 200:5 1.2 20 40 0.3 B-0.5 C-50 15 110 34 2.5
750491060 300:5 1.2 30 60 0.3 B-0.5 C-50 15 110 34 2.5
750491080 400:5 1.2 40 80 0.3 B-0.5 C-50 15 110 34 2.5
750491120 600:5 1.2 50 95 0.3 B-0.5 C-50 15 110 34 2.5
750491160 800:5 1.2 60 120 0.3 B-0.5 C-50 15 110 34 2.5
750491200 1000:5 1.2 75 135 0.3 B-0.5 C-50 15 110 34 2.5
750491240 1200:5 1.2 84 150 0.3 B-0.5 C-50 15 110 34 2.5
Notes:

ACH-17 15 kV CURRENT TRANSFORMER

requirements.
Mechanical
Mechan
h ical characteristics
Insulation Material Colors
Colo Weight (lbs.)
Resin
R i Gray*
G 63.8
11.85 (301) 7 (177.8)
5.90 (150)
H1
8.58 (217.932)
Nameplate
H2
1/4 Secondary
(6.35) terminals
11.69 (297)
ONE
SECONDARY
MARKING H1 H2
(Single
Primary
Ratio) X1 X2


Power-Frequency
Ratio time time
30C (kVrms) (kVrms)
750561010 50:5 1.2 5 10 0.3 B-0.5 C-50 15 110 34 2.5

750561015 75:5 1.2 7.5 15 0.3 B-0.5 C-50 15 110 34 2.5
750561020 100:5 1.2 10 20 0.3 B-0.5 C-50 15 110 34 2.5
750561030 150:5 1.2 15 30 0.3 B-1.0 C-50 15 110 34 2.5
750561040 200:5 1.2 20 40 0.3 B-1.0 C-50 15 110 34 2.5
750561060 300:5 1.2 30 60 0.3 B-1.0 C-50 15 110 34 2.5
750561080 400:5 1.2 40 80 0.3 B-1.8 C-100 15 110 34 2.5
750561120 600:5 1.2 50 95 0.3 B-1.8 C-100 15 110 34 2.5
750561160 800:5 1.2 60 120 0.3 B-1.8 C-100 15 110 34 2.5
750561200 1000:5 1.2 75 135 0.3 B-1.8 C-200 15 110 34 2.5
750561240 1200:5 1.2 84 150 0.3 B-1.8 C-200 15 110 34 2.5
Notes:

ACI-17 15 kV CURRENT TRANSFORMER

requirements.
Resin Gray* 46.2
10.6 (270) 5.8 (148) 4.9 (125)
P2
10.6 (270.5)
8.6 (220)
Nameplate
Ground
connector P1
Secondary
(1/4) terminals
ONE
SECONDARY
MARKING H1 H2
(Single
Primary
Ratio) X1 X2


ACI-17 15 kV CURRENT TRANSFORMER
Power-Frequency
Ratio time time
30C (kVrms) (kVrms)
750511010 50:5 1.2 5 10 0.3 B-0.5 C-50 15 110 34 2.5

750511015 75:5 1.2 7.5 15 0.3 B-0.5 C-50 15 110 34 2.5
750511020 100:5 1.2 10 20 0.3 B-0.5 C-50 15 110 34 2.5
750511030 150:5 1.2 15 30 0.3 B-0.5 C-50 15 110 34 2.5
750511040 200:5 1.2 20 40 0.3 B-0.5 C-50 15 110 34 2.5
750511060 300:5 1.2 30 60 0.3 B-0.5 C-50 15 110 34 2.5
750511080 400:5 1.2 40 80 0.3 B-0.5 C-50 15 110 34 2.5
750511120 600:5 1.2 50 95 0.3 B-0.9 C-50 15 110 34 2.5
750511160 800:5 1.2 60 120 0.3 B-0.9 C-50 15 110 34 2.5
750511200 1000:5 1.2 75 135 0.3 B-0.9 C-50 15 110 34 2.5
750511240 1200:5 1.2 84 150 0.3 B-0.9 C-100 15 110 34 2.5
Notes:

IINDOOR plate double isolation. The concentric distribution of the coils prevents
60 Hertz
6 magnetic ux leakage, achieving greater accuracy and higher capacity to

requirements.
UL Recognized
Recog
o nized Component
Resin Gray* 55
23 (584)
6.79 (172.5)
3.94 (100)
10.34 (263)
9 (229)
5.13 (130)
Nameplate
9.63 (245)
ONE
SECONDARY
MARKING H1 H2
(Single
Primary
Ratio) X1 X2


Power-Frequency
Ratio time time
30C (kVrms) (kVrms)
750961001 5:5 1.5 0.5 1 0.3 B-1.8 C-200 15 110 34 2.5

750961002 10:5 1.5 1 2 0.3 B-1.8 C-200 15 110 34 2.5
750961003 15:5 1.5 1.5 3 0.3 B-1.8 C-200 15 110 34 2.5
750961004 20:5 1.5 2 4 0.3 B-1.8 C-200 15 110 34 2.5
750961005 25:5 1.5 2.5 5 0.3 B-1.8 C-200 15 110 34 2.5
750961006 30:5 1.5 3 6 0.3 B-1.8 C-200 15 110 34 2.5
750961008 40:5 1.5 4 8 0.3 B-1.8 C-200 15 110 34 2.5
750961010 50:5 1.5 5 10 0.3 B-1.8 C-200 15 110 34 2.5
750961015 75:5 1.5 7.5 15 0.3 B-1.8 C-200 15 110 34 2.5
750961020 100:5 1.5 10 20 0.3 B-1.8 C-200 15 110 34 2.5
750961030 150:5 1.5 15 30 0.3 B-1.8 C-200 15 110 34 2.5
750961040 200:5 1.5 20 40 0.3 B-1.8 C-200 15 110 34 2.5
750961060 300:5 1.5 30 60 0.3 B-1.8 C-200 15 110 34 2.5
750961080 400:5 1.5 40 80 0.3 B-1.8 C-200 15 110 34 2.5
750961120 600:5 1.5 50 95 0.3 B-1.8 C-200 15 110 34 2.5
750961160 800:5 1.5 60 120 0.3 B-1.8 C-200 15 110 34 2.5
750961200 1000:5 1.5 75 135 0.3 B-1.8 C-200 15 110 34 2.5
750961240 1200:5 1.2 84 150 0.3 B-1.8 C-200 15 110 34 2.5
750969001 5:5 1.5 0.5 1 0.15 B0.5 - 15 110 34 2.5
750969002 10:5 1.5 1 2 0.15 B0.5 - 15 110 34 2.5
750969003 15:5 1.5 1.5 3 0.15 B0.5 - 15 110 34 2.5
750969004 20:5 1.5 2 4 0.15 B0.5 - 15 110 34 2.5
750969005 25:5 1.5 2.5 5 0.15 B0.5 - 15 110 34 2.5
750969006 30:5 1.5 3 6 0.15 B0.5 - 15 110 34 2.5
750969008 40:5 1.5 4 8 0.15 B0.5 - 15 110 34 2.5
750969010 50:5 1.5 5 10 0.15 B0.5 - 15 110 34 2.5
750969015 75:5 1.5 7.5 15 0.15 B0.5 - 15 110 34 2.5
750969020 100:5 1.5 10 20 0.15 B0.5 - 15 110 34 2.5
750969030 150:5 1.5 15 30 0.15 B0.5 - 15 110 34 2.5
750969040 200:5 1.5 20 40 0.15 B0.5 - 15 110 34 2.5
750969060 300:5 1.5 30 60 0.15 B0.5 - 15 110 34 2.5
750969080 400:5 1.5 40 80 0.15 B0.5 - 15 110 34 2.5
750969120 600:5 1.5 50 95 0.15 B0.5 - 15 110 34 2.5
750969160 800:5 1.5 60 120 0.15 B0.5 - 15 110 34 2.5
750969200 1000:5 1.5 75 135 0.15 B0.5 - 15 110 34 2.5
750969240 1200:5 1.2 84 150 0.15 B0.5 - 15 110 34 2.5

Power-Frequency
Ratio time time
30C (kVrms) (kVrms)

750967001 5:5 1.5 0.5 1 0.15S B0.5 - 15 110 34 2.5
750967002 10:5 1.5 1 2 0.15S B0.5 - 15 110 34 2.5
750967003 15:5 1.5 1.5 3 0.15S B0.5 - 15 110 34 2.5
750967004 20:5 1.5 2 4 0.15S B0.5 - 15 110 34 2.5
750967005 25:5 1.5 2.5 5 0.15S B0.5 - 15 110 34 2.5
750967006 30:5 1.5 3 6 0.15S B0.5 - 15 110 34 2.5
750967008 40:5 1.5 4 8 0.15S B0.5 - 15 110 34 2.5
750967010 50:5 1.5 5 10 0.15S B0.5 - 15 110 34 2.5
750967015 75:5 1.5 7.5 15 0.15S B0.5 - 15 110 34 2.5
750967020 100:5 1.5 10 20 0.15S B0.5 - 15 110 34 2.5
750967030 150:5 1.5 15 30 0.15S B0.5 - 15 110 34 2.5
750967040 200:5 1.5 20 40 0.15S B0.5 - 15 110 34 2.5
750967060 300:5 1.5 30 60 0.15S B0.5 - 15 110 34 2.5
750967080 400:5 1.5 40 80 0.15S B0.5 - 15 110 34 2.5
750967120 600:5 1.5 50 95 0.15S B0.5 - 15 110 34 2.5
750967160 800:5 1.5 60 120 0.15S B0.5 - 15 110 34 2.5
750967200 1000:5 1.5 75 135 0.15S B0.5 - 15 110 34 2.5
750967240 1200:5 1.2 84 150 0.15S B0.5 - 15 110 34 2.5

750968040 200:5 2.0 20 40 0.15 B-1.8 - 15 110 34 2.5
750968120 600:5 2.0 50 95 0.15 B-1.8 - 15 110 34 2.5
750968200 1000:5 1.5 75 135 0.15 B-1.8 - 15 110 34 2.5
750968240 1200:5 1.2 84 150 0.15 B-1.8 - 15 110 34 2.5

Notes:


requirements.
Resin Gray* 35.3
9.37 (238)
6.69 (170) 7.08 (180) 5.1 (130)
H2
5.5 (140)
10.03 (255)
H1
Sealable
cover
Secondary
terminals M6
ONE
SECONDARY
MARKING H1 H2
(Single
Primary
Ratio) X1 X2


Power-Frequency
Ratio time time
30C (kVrms) (kVrms)
750681001 5:5 1.2 0.5 1 0.3 B-0.5 C-50 25 150 50 2.5

750681002 10:5 1.2 1 2 0.3 B-0.5 C-50 25 150 50 2.5
750681003 15:5 1.2 1.5 3 0.3 B-0.5 C-50 25 150 50 2.5
750681004 20:5 1.2 2 4 0.3 B-0.5 C-50 25 150 50 2.5
750681005 25:5 1.2 2.5 5 0.3 B-0.5 C-50 25 150 50 2.5
750681006 30:5 1.2 3 6 0.3 B-0.5 C-50 25 150 50 2.5
750681008 40:5 1.2 4 8 0.3 B-0.5 C-50 25 150 50 2.5
750681010 50:5 1.2 5 10 0.3 B-0.5 C-50 25 150 50 2.5
750681015 75:5 1.2 7.5 15 0.3 B-0.5 C-50 25 150 50 2.5
750681020 100:5 1.2 10 20 0.3 B-0.5 C-50 25 150 50 2.5
750681030 150:5 1.2 15 30 0.3 B-0.5 C-50 25 150 50 2.5
750681040 200:5 1.2 20 40 0.3 B-0.5 C-50 25 150 50 2.5
750681060 300:5 1.2 30 60 0.3 B-0.5 C-50 25 150 50 2.5
750681080 400:5 1.2 40 80 0.3 B-0.5 C-50 25 150 50 2.5
750681120 600:5 1.2 50 95 0.3 B-0.5 C-50 25 150 50 2.5
750681160 800:5 1.2 60 120 0.3 B-0.5 C-50 25 150 50 2.5
750681200 1000:5 1.2 75 135 0.3 B-0.5 C-50 25 150 50 2.5
750681240 1200:5 1.2 84 150 0.3 B-0.5 C-50 25 150 50 2.5
Notes:


requirements.
Mechanical
Mechan
h ical characteristics
Colo Weight (lbs.)
Resin
R i Gray*
G 63.8
11.85 (301) 7 (177.8)
5.90 (150)
H1
8.58 (217.932)
Nameplate
H2
1/4 Secondary
(6.35) terminals
11.69 (297)
ONE
SECONDARY
MARKING H1 H2
(Single
Primary
Ratio) X1 X2


Power-Frequency
Ratio time time
30C (kVrms) (kVrms)
750741015 75:5 1.2 7.5 15 0.3 B-0.5 C-50 25 150 50 2.5

750741020 100:5 1.2 10 20 0.3 B-0.5 C-50 25 150 50 2.5
750741030 150:5 1.2 15 30 0.3 B-0.5 C-50 25 150 50 2.5
750741040 200:5 1.2 20 40 0.3 B-1.0 C-50 25 150 50 2.5
750741060 300:5 1.2 30 60 0.3 B-1.0 C-50 25 150 50 2.5
750741080 400:5 1.2 40 80 0.3 B-1.0 C-50 25 150 50 2.5
750741120 600:5 1.2 50 95 0.3 B-1.8 C-100 25 150 50 2.5
750741160 800:5 1.2 60 120 0.3 B-1.8 C-100 25 150 50 2.5
750741200 1000:5 1.2 75 135 0.3 B-1.8 C-200 25 150 50 2.5
750741240 1200:5 1.2 84 150 0.3 B-1.8 C-200 25 150 50 2.5

750746040 200:5 2.0 20 40 0.15 B-1.8 - 25 150 50 2.5
750746120 600:5 1.2 75 135 0.15 B-1.8 - 25 150 50 2.5
750746200 1000:5 1.2 75 135 0.15 B-1.8 - 25 150 50 2.5
750746240 1200:5 1.2 75 135 0.15 B-1.8 - 25 150 50 2.5
Notes:

ACA-36 34.5 kV CURRENT TRANSFORMER

requirements.
Resin Gray* 35.3
6.69 (170) 6.69 (170)
5.11 (130)
14.84 (377)
P1 P2
Sealable
cover
Secondary Connection
terminal to ground
5.51 (14)
ONE
SECONDARY
MARKING H1 H2
(Single
Primary
Ratio) X1 X2


ACA-36 34.5 kV CURRENT TRANSFORMER
Power-Frequency
Ratio time time
30C (kVrms) (kVrms)
751111001 5:5 1.2 0.5 1 0.3 B-0.5 C-50 34.5 200 70 2.5
751111002 10:5 1.2 1 2 0.3 B-0.5 C-50 34.5 200 70 2.5
751111003 15:5 1.2 1.5 3 0.3 B-0.5 C-50 34.5 200 70 2.5
751111004 20:5 1.2 2 4 0.3 B-0.5 C-50 34.5 200 70 2.5
751111005 25:5 1.2 2.5 5 0.3 B-0.5 C-50 34.5 200 70 2.5
751111006 30:5 1.2 3 6 0.3 B-0.5 C-50 34.5 200 70 2.5
751111008 40:5 1.2 4 8 0.3 B-0.5 C-50 34.5 200 70 2.5
751111010 50:5 1.2 5 10 0.3 B-0.5 C-50 34.5 200 70 2.5
751111015 75:5 1.2 7.5 15 0.3 B-0.5 C-50 34.5 200 70 2.5
751111020 100:5 1.2 10 20 0.3 B-0.5 C-50 34.5 200 70 2.5
751111030 150:5 1.2 15 30 0.3 B-0.5 C-50 34.5 200 70 2.5
751111040 200:5 1.2 20 40 0.3 B-0.5 C-50 34.5 200 70 2.5
751111060 300:5 1.2 30 60 0.3 B-0.5 C-50 34.5 200 70 2.5
751111080 400:5 1.2 40 80 0.3 B-0.5 C-50 34.5 200 70 2.5
751111120 600:5 1.2 50 95 0.3 B-0.5 C-50 34.5 200 70 2.5
751111160 800:5 1.2 60 120 0.3 B-0.5 C-50 34.5 200 70 2.5
751111200 1000:5 1.2 75 135 0.3 B-0.5 C-50 34.5 200 70 2.5
751111240 1200:5 1.2 84 150 0.3 B-0.5 C-50 34.5 200 70 2.5
Notes:

ACF-36 34.5 kV CURRENT TRANSFORMER

requirements.
Resin Gray* 79.4
10.62 (270)
8.26 (210)
6.1 (155)
H1
7 (178)
13.97 (355)
H2
Secondary Sealable Connection 11.61 (295)
terminals cover to ground
13.89 (353)
ONE
SECONDARY
MARKING H1 H2
(Single
Primary
Ratio) X1 X2


ACF-36 34.5 kV CURRENT TRANSFORMER
Power-Frequency
Ratio time time
30C (kVrms) (kVrms)
751161001 5:5 1.2 0.5 1 0.3 B-1.8 C-100 34.5 200 70 2.5
751161002 10:5 1.2 1 2 0.3 B-1.8 C-100 34.5 200 70 2.5
751161003 15:5 1.2 1.5 3 0.3 B-1.8 C-100 34.5 200 70 2.5
751161004 20:5 1.2 2 4 0.3 B-1.8 C-100 34.5 200 70 2.5
751161005 25:5 1.2 2.5 5 0.3 B-1.8 C-100 34.5 200 70 2.5
751161006 30:5 1.2 3 6 0.3 B-1.8 C-100 34.5 200 70 2.5
751161008 40:5 1.2 4 8 0.3 B-1.8 C-100 34.5 200 70 2.5
751161010 50:5 1.2 5 10 0.3 B-1.8 C-100 34.5 200 70 2.5
751161015 75:5 1.2 7.5 15 0.3 B-1.8 C-100 34.5 200 70 2.5
751161020 100:5 1.2 10 20 0.3 B-1.8 C-100 34.5 200 70 2.5
751161030 150:5 1.2 15 30 0.3 B-1.8 C-100 34.5 200 70 2.5
751161040 200:5 1.2 20 40 0.3 B-1.8 C-100 34.5 200 70 2.5
751161060 300:5 1.2 30 60 0.3 B-1.8 C-100 34.5 200 70 2.5
751161080 400:5 1.2 40 80 0.3 B-1.8 C-100 34.5 200 70 2.5
751161120 600:5 1.2 50 95 0.3 B-1.8 C-100 34.5 200 70 2.5
751161160 800:5 1.2 60 120 0.3 B-1.8 C-100 34.5 200 70 2.5
751161200 1000:5 1.2 75 135 0.3 B-1.8 C-100 34.5 200 70 2.5
751161240 1200:5 1.2 84 150 0.3 B-1.8 C-200 34.5 200 70 2.5
Notes:

KCB-17 15 kV COMBINED TRANSFORMER
ARTECHE KCB series are dry type indoor service dead-front combination
CT-PT
The core is encapsulated with Type B epoxy resin which provides excellent
mounting inside switchgear or enclosures.
KCB 200 A KCB 600 A
INDOOR
60 Hertz Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC
requirements.
The primary terminals are standard 200 or 600 Ampere rated dead-front
bushing well and can be connected using IEEE 368 standard inserts and
elbow connectors.
The secondary terminals are 1/4 slotted screws with at and lock washers
located inside a metallic terminal cover with two 1 NPT conduit hubs. The
ground terminal is provided inside the terminal cover along with a manually
operated CT secondary shorting device for safety purposes.
Metallized resin Gray 150
KCB 200 A 14.13 (359)

9.84 (250)
6.69 (170)
Name plate
15.19 (386)
10 (254)
Secondary
terminals Terminal
1/4-20 box
V2 V2
VT
1 hole 7/16 to
C1
CT
C2
ground connection
19.84 (503)
Drawing number: 4286592 (200 A) / 4287655 (600 A)
KCB 600 A
3 (76)
ONE SECONDARY
H1 H2
MARKING
(Single
Primary
18.33 (466)
C1 C2
Ratio)
H0
V1 V2

Power-Frequency
Withstand Voltage
Continuous (1 min)
Short- Short- IEEE
Current Thermal IEEE Metering Nominal
time time Metering Power
Ratio Current Accuracy Voltage BIL Power
Code Thermal Mechanical Accuracy frequency
(Primary: Rating [Voltage System (kV) frequency
Current Current [Current secondary
Secondary) Factor @ Transformer] (kV) applied
(kA/1s) (kApeak) Transformer] applied
30C voltage test
voltage test
(kVrms)
(kVrms)
770034011 5:5 2.0 0.5 1.25 0.3 B-0.5 0.3 W,X,M,Y/1.2Z 15 110 34 2.5
770034021 10:5 2.0 1 2.5 0.3 B-0.5 0.3 W,X,M,Y/1.2Z 15 110 34 2.5
770034031 15:5 2.0 1.5 3.75 0.3 B-0.5 0.3 W,X,M,Y/1.2Z 15 110 34 2.5
770034041 20:5 2.0 2 5 0.3 B-0.5 0.3 W,X,M,Y/1.2Z 15 110 34 2.5
770034051 25:5 2.0 2.5 6.25 0.3 B-0.5 0.3 W,X,M,Y/1.2Z 15 110 34 2.5
770034061 30:5 2.0 3 7.5 0.3 B-0.5 0.3 W,X,M,Y/1.2Z 15 110 34 2.5
770034081 40:5 2.0 4 10 0.3 B-0.5 0.3 W,X,M,Y/1.2Z 15 110 34 2.5
770034101 50:5 2.0 5 12.5 0.3 B-0.5 0.3 W,X,M,Y/1.2Z 15 110 34 2.5
770034151 75:5 2.0 7.5 18.75 0.3 B-0.5 0.3 W,X,M,Y/1.2Z 15 110 34 2.5
770034201 100:5 2.0 10 25 0.3 B-0.5 0.3 W,X,M,Y/1.2Z 15 110 34 2.5
770035301 150:5 1.33 10 25 0.3 B-0.5 0.3 W,X,M,Y/1.2Z 15 110 34 2.5
770035401 200:5 1.0 10 25 0.3 B-0.5 0.3 W,X,M,Y/1.2Z 15 110 34 2.5
770031131 300:5 1.5 30 75 0.3 B-0.5 0.3 W,X,M,Y/1.2Z 15 110 34 2.5
770031141 400:5 1.5 40 100 0.3 B-0.5 0.3 W,X,M,Y/1.2Z 15 110 34 2.5
770031151 600:5 1.0 60 150 0.3 B-0.5 0.3 W,X,M,Y/1.2Z 15 110 34 2.5

770031101 100:5 2.0 10 25 0.15 B-0.5 0.3 W,X,M,Y/1.2Z 15 110 34 2.5
770031121 200:5 2.0 20 50 0.15 B-0.5 0.3 W,X,M,Y/1.2Z 15 110 34 2.5
770031151 600:5 1.0 48 120 0.15 B-0.5 0.3 W,X,M,Y/1.2Z 15 110 34 2.5
Voltage Ratings Notes:

Rated
Thermal Continuous Rated
Secondary Voltage
VT Ratio Primary (V) Burden Voltage Factor
(V) Factor 30s
(VA) (Un)
(Un)
60:1 7200/12470GY 120 750 1.1 1.25
Additional VT ratios are available. Please contact Arteche for details.

ARTECHE KCB series are dry type indoor service dead-front combination
CT-PT
KCB 200 A KCB 600 A
INDOOR
60 Hertz Partial Discharge measurements exceed the IEEE, CAN/CSA and IEC
requirements.
The primary terminals are standard 200 or 600 Ampere rated dead-front
bushing well and can be connected using IEEE 368 standard inserts and
elbow connectors.
The secondary terminals are 1/4 slotted screws with at and lock washers
located inside a metallic terminal cover with two 1 NPT conduit hubs. The
ground terminal is provided inside the terminal cover along with a manually
operated CT secondary shorting device for safety purposes.
Metallized resin Gray 150
KCB 200 A 14.13 (359)

9.84 (250)
6.69 (170)
Name plate
15.19 (386)
10 (254)
Secondary
terminals Terminal
1/4-20 box
V2 V2
VT
1 hole 7/16 to
C1
CT
C2
ground connection
19.84 (503)
Drawing number: 9449854 (200 A) / 4287736 (600 A)
KCB 600 A
3 (76)
ONE SECONDARY
18.33 (466)
H1 H2
MARKING
(Single
Primary
C1 C2
Ratio)
H0
V1 V2

Power-Frequency
Withstand Voltage
Continuous (1 min)
Short- Short- IEEE
Current Thermal IEEE Metering Nominal
time time Metering Power
Ratio Current Accuracy Voltage BIL Power
Code Thermal Mechanical Accuracy frequency
(Primary: Rating [Voltage System (kV) frequency
Current Current [Current secondary
Secondary) Factor @ Transformer] (kV) applied
(kA/1s) (kApeak) Transformer] applied
30C voltage test
voltage test
(kVrms)
(kVrms)
770104016 5:5 2.0 0.5 1.25 0.3 B-0.5 0.3 W,X,M,Y/1.2Z 25 125 50 2.5
770104026 10:5 2.0 1 2.5 0.3 B-0.5 0.3 W,X,M,Y/1.2Z 25 125 50 2.5
770104036 15:5 2.0 1.5 3.75 0.3 B-0.5 0.3 W,X,M,Y/1.2Z 25 125 50 2.5
770104046 20:5 2.0 2 5 0.3 B-0.5 0.3 W,X,M,Y/1.2Z 25 125 50 2.5
770104056 25:5 2.0 2.5 6.25 0.3 B-0.5 0.3 W,X,M,Y/1.2Z 25 125 50 2.5
770104066 30:5 2.0 3 7.5 0.3 B-0.5 0.3 W,X,M,Y/1.2Z 25 125 50 2.5
770104086 40:5 2.0 4 10 0.3 B-0.5 0.3 W,X,M,Y/1.2Z 25 125 50 2.5
770104106 50:5 2.0 5 12.5 0.3 B-0.5 0.3 W,X,M,Y/1.2Z 25 125 50 2.5
770104156 75:5 2.0 7.5 18.75 0.3 B-0.5 0.3 W,X,M,Y/1.2Z 25 125 50 2.5
770104206 100:5 2.0 10 25 0.3 B-0.5 0.3 W,X,M,Y/1.2Z 25 125 50 2.5
770105306 150:5 1.33 10 25 0.3 B-0.5 0.3 W,X,M,Y/1.2Z 25 125 50 2.5
770105406 200:5 1.0 10 25 0.3 B-0.5 0.3 W,X,M,Y/1.2Z 25 125 50 2.5
770101136 300:5 1.5 30 75 0.3 B-0.5 0.3 W,X,M,Y/1.2Z 25 125 50 2.5
770101146 400:5 1.5 40 100 0.3 B-0.5 0.3 W,X,M,Y/1.2Z 25 125 50 2.5
770101156 600:5 1.0 60 150 0.3 B-0.5 0.3 W,X,M,Y/1.2Z 25 125 50 2.5

770101106 100:5 2.0 10 25 0.15 B-0.5 0.3 W,X,M,Y/1.2Z 25 125 50 2.5
770101126 200:5 2.0 20 50 0.15 B-0.5 0.3 W,X,M,Y/1.2Z 25 125 50 2.5
770101156 600:5 1.0 48 120 0.15 B-0.5 0.3 W,X,M,Y/1.2Z 25 125 50 2.5

Rated
Secondary Voltage
(V) Factor 30s
(VA) (Un)
(Un)
120:1 14400/24940GY 120 750 1.1 1.25

5 kV 69 kV
OUTDOOR
INSTRUMENT
TRANSFORMERS
& METERING
UNITS
VRL-7 5 kV VOLTAGE TRANSFORMER
ARTECHE UR/VR series are dry type outdoor service voltage transformers.
internal dielectric properties and mechanical strength. The external layer of
Cycloaliphatic Epoxy Resin (CEP) provides resistance to ultraviolet rays and the
effects of tracking and erosion on the exterior of the transformer ensuring a
long mechanical and electrical life. The transformer is maintenance free.
OUTDOOR
60 Hertz The external layer can be manufactured with Hydrophobic Cycloaliphatic
Epoxy Resin (HCEP) which improves service life expectancy due to its
improved tracking and erosion resistance. HCEP additionally increases
the transformers weatherability and offers better performance in heavily
polluted environments.
Partial discharge measurements exceed IEEE C57.13 2008 requirements.

Insulation Material Colors Weight (lbs.) Creepage distance (in) Strike distance (in)
Resin Gray * 40 15.8 3
11.25 (286)
2 x 8.5 (2 x 216)
2 x 6.25 (2 x 159)
12 (305)
Terminal box
Two holes to conduit

pipe A1 - NPT
10.7 (272)
PRIMARY TERMINAL GROUND TERMINAL SECONDARY TERMINAL

/4
1
CONNEC-
TIONS
Type: TE-4T Type: TE-12-250 Type: Quick Connector

Material: Copper Material: Copper Material: Brass
Range: 8SOL-4TRE Range: 4TRE-250MCM
SINGLE SECONDARY
H1 H2 H1 H2
MARKING
(Single Fuse: 16A
Primary
Ratio) X1 X2 X1 X2
FUSED UNFUSED
Approximate dimensions in inches (mm). * Brown color available upon request

Power-Frequency
Continuous Rated Highest Withstand Voltage (1
Secon- IEEE Rated Voltage Thermal Nominal min)
Primary BIL
Code * (CEP) Ratio dary Metering Voltage Factor Burden Voltage
(V) (kV) Primary & Secondary
(V) Accuracy Factor 30 s (VA) System
(Un) (Un) (kV) Secondary Winding
(kVrms) (kVrms)
With FUSE in the secondary box
757091020 20:1 2400/4160Y 120 0.3 W,X,M,Y 1.1 1.5 1000 5 60 19 2.5
757091035 35:1 4200/4200Y 120 0.3 W,X,M,Y 1.1 1.5 1000 5 60 19 2.5
757091040 40:1 4800/4800Y 120 0.3 W,X,M,Y 1.1 1.5 1000 5 60 19 2.5
Without FUSE in the secondary box
757090020 20:1 2400/4160Y 120 0.3 W,X,M,Y 1.1 1.5 1000 5 60 19 2.5
757090035 35:1 4200/4200Y 120 0.3 W,X,M,Y 1.1 1.5 1000 5 60 19 2.5
757090040 40:1 4800/4800Y 120 0.3 W,X,M,Y 1.1 1.5 1000 5 60 19 2.5
* For HCEP Option add (H) to the end of the code number.
Notes:

URJ-17 15 kV VOLTAGE TRANSFORMER
OUTDOOR The external layer can be manufactured with Hydrophobic Cycloaliphatic

60 Hertz Epoxy Resin (HCEP) which improves service life expectancy due to its

requirements.
+
Resin Gray* 94.6 21.45/25 11.61/12.5+
12.99 (330) 8.26 (210) Nameplate

M12
8.62 (219)
17.8 (453)
H1
Lifting holes
3/4
2 holes to
conduit pipe
1 NPT 10 (254)
Drawing number:
Fused: 4286572 / 4286596+
Unfused: 4286820

/4
1
CONNEC-
TIONS

SINGLE SECONDARY ONE SECONDARY WITH TAP
H1 H2 H1 H2 H1 H2 H1 H2
MARKING
(Single
Fuse: 16A Fuse: 16A
Primary
Ratio)
X1 X2 X1 X2 X1 X2 X3 X1 X2 X3
FUSED UNFUSED FUSED UNFUSED

Power-Frequency
Nominal
Code * Primary Secondary Voltage BIL
Ratio Metering Voltage Factor Burden
(CEP) (V) (V) System (kV) Primary & Secondary
(Un) (Un)
(kVrms) (kVrms)
757061020 20:1 2400/4156GY 120 0.3 W,X,M,Y 1.1 1.5 750 5 60 19 2.5
2400/4156GY 0.3 W,X /
757063060 20/60:1 120 1.1 1.5 750 15 110 34 2.5
& 7200/12470GY 0.3W,X,M,Y
757061060 60:1 7200/12470GY 120 0.3 W,X,M,Y 1.1 1.5 750 15 110 34 2.5
757061063 63.5:1 7620/13200GY 120 0.3 W,X,M,Y 1.1 1.5 750 15 110 34 2.5
757061070 70:1 8400/14550GY 120 0.3 W,X,M,Y 1.1 1.5 750 15 110 34 2.5
757065020 20:1 2400/4156GY 120 0.3 W,X,M,Y,Z 1.1 1.25 1500 5 60 19 2.5
2400/4156GY 0.3 W,X /
757066060 20/60:1 120 1.1 1.25 1500 15 110 34 2.5
& 7200/12470GY 0.3W,X,M,Y
757065060 60:1 7200/12470GY 120 0.3 W,X,M,Y,Z 1.1 1.25 1500 15 110 34 2.5
757065063 63.5:1 7620/13200GY 120 0.3 W,X,M,Y 1.1 1.25 1500 15 110 34 2.5
757065070 70:1 8400/14550GY 120 0.3 W,X,M,Y,Z 1.1 1.25 1500 15 110 34 2.5
757067020+ 20:1 2400/4156GY 120 0.3 W,X,M,Y,Z 1.1 1.25 1500 5 60 19 2.5
2400/4156GY 0.3 W,X /
757068020+ 20/60:1 120 1.1 1.25 1500 15 110 34 2.5
& 7200/12470GY 0.3W,X,M,Y
+
757067060 60:1 7200/12470GY 120 0.3 W,X,M,Y,Z 1.1 1.25 1500 15 110 34 2.5
757067063+ 63.5:1 7620/13200GY 120 0.3 W,X,M,Y 1.1 1.25 1500 15 110 34 2.5
757067070+ 70:1 8400/14550GY 120 0.3 W,X,M,Y,Z 1.1 1.25 1500 15 110 34 2.5
757064020 20:1 2400/4156GY 120 0.3 W,X,M,Y 1.1 1.5 750 5 60 19 2.5
757064060 60:1 7200/12470GY 120 0.3 W,X,M,Y 1.1 1.5 750 15 110 34 2.5
757064063 63.5:1 7620/13200GY 120 0.3 W,X,M,Y 1.1 1.5 750 15 110 34 2.5
757064070 70:1 8400/14550GY 120 0.3 W,X,M,Y 1.1 1.5 750 15 110 34 2.5
757060020 20:1 2400/4156GY 120 0.3 W,X,M,Y,Z 1.1 1.25 1500 5 60 19 2.5
757060060 60:1 7200/12470GY 120 0.3 W,X,M,Y,Z 1.1 1.25 1500 15 110 34 2.5
757060063 63.5:1 7620/13200GY 120 0.3 W,X,M,Y 1.1 1.25 1500 15 110 34 2.5
757060070 70:1 8400/14550GY 120 0.3 W,X,M,Y,Z 1.1 1.25 1500 15 110 34 2.5
+
Extended creepage distance
Notes:

URL-17 15 kV VOLTAGE TRANSFORMER


requirements.
Mechanical
M h i l characteristics
h t i ti
Resin Gray* 80 21.65 12.2
12.08 (307) 8.03 (204) Nameplate

M12
8.62 (219)
17.12 (235)
H1
Lifting holes
3/4
2 holes to
conduit pipe
1 NPT 10 (254)
Drawing number:
Fused: 4286570
Unfused: 4286769

/4
1
CONNEC-
TIONS

SINGLE SECONDARY
H1 H2 H1 H2
MARKING
(Single
Fuse: 16A
Primary
Ratio)
X1 X2 X1 X2
FUSED UNFUSED

URL-17 15 kV VOLTAGE TRANSFORMER
Power-Frequency
Nominal
(Un) (Un)
(kVrms) (kVrms)
757031020 20:1 2400/4160GY 120 0.3 W,X,M,Y 1.1 1.5 500 5 60 19 2.5
757031035 35:1 4200/7280GY 120 0.3 W,X,M,Y 1.1 1.5 500 5 60 19 2.5
757031040 40:1 4200/4200GY 120 0.3 W,X,M,Y 1.1 1.5 500 5 60 19 2.5
757031042 42:1 5040/8730GY 120 0.3 W,X,M,Y 1.1 1.5 500 8.7 75 26 2.5
757031060 60:1 7200/12470GY 120 0.3 W,X,M,Y 1.1 1.5 500 15 110 34 2.5
757031063 63.5:1 7620/13200GY 120 0.3 W,X,M,Y 1.1 1.5 500 15 110 34 2.5
757031066 66.4:1 7968/13800GY 120 0.3 W,X,M,Y 1.1 1.5 500 15 110 34 2.5
757031067 66.67:1 8000/13856GY 120 0.3 W,X,M,Y 1.1 1.5 500 15 110 34 2.5
757031070 70:1 8400/14550GY 120 0.3 W,X,M,Y 1.1 1.5 500 15 110 34 2.5
757035020 20:1 2400/4160GY 120 0.3 W,X,M,Y 1.1 1.25 750 5 60 19 2.5
757035035 35:1 4200/7280GY 120 0.3 W,X,M,Y 1.1 1.25 750 5 60 19 2.5
757035040 40:1 4200/4200GY 120 0.3 W,X,M,Y 1.1 1.25 750 5 60 19 2.5
757035042 42:1 5040/8730GY 120 0.3 W,X,M,Y 1.1 1.25 750 8.7 75 26 2.5
757035060 60:1 7200/12470GY 120 0.3 W,X,M,Y 1.1 1.25 750 15 110 34 2.5
757035063 63.5:1 7620/13200GY 120 0.3 W,X,M,Y 1.1 1.25 750 15 110 34 2.5
757035066 66.4:1 7968/13800GY 120 0.3 W,X,M,Y 1.1 1.25 750 15 110 34 2.5
757035067 66.67:1 8000/13856GY 120 0.3 W,X,M,Y 1.1 1.25 750 15 110 34 2.5
757035070 70:1 8400/14550GY 120 0.3 W,X,M,Y 1.1 1.25 750 15 110 34 2.5
757034020 20:1 2400/4160GY 120 0.3 W,X,M,Y 1.1 1.5 500 5 60 19 2.5
757034035 35:1 4200/7280GY 120 0.3 W,X,M,Y 1.1 1.5 500 5 60 19 2.5
757034040 40:1 4200/4200GY 120 0.3 W,X,M,Y 1.1 1.5 500 5 60 19 2.5
757034042 42:1 5040/8730GY 120 0.3 W,X,M,Y 1.1 1.5 500 8.7 75 26 2.5
757034060 60:1 7200/12470GY 120 0.3 W,X,M,Y 1.1 1.5 500 15 110 34 2.5
757034063 63.5:1 7620/13200GY 120 0.3 W,X,M,Y 1.1 1.5 500 15 110 34 2.5
757034066 66.4:1 7968/13800GY 120 0.3 W,X,M,Y 1.1 1.5 500 15 110 34 2.5
757034067 66.67:1 8000/13856GY 120 0.3 W,X,M,Y 1.1 1.5 500 15 110 34 2.5
757034070 70:1 8400/14550GY 120 0.3 W,X,M,Y 1.1 1.5 500 15 110 34 2.5
757030020 20:1 2400/4160GY 120 0.3 W,X,M,Y 1.1 1.25 750 5 60 19 2.5
757030035 35:1 4200/7280GY 120 0.3 W,X,M,Y 1.1 1.25 750 5 60 19 2.5
757030040 40:1 4200/4200GY 120 0.3 W,X,M,Y 1.1 1.25 750 5 60 19 2.5
757030042 42:1 5040/8730GY 120 0.3 W,X,M,Y 1.1 1.25 750 8.7 75 26 2.5
757030060 60:1 7200/12470GY 120 0.3 W,X,M,Y 1.1 1.25 750 15 110 34 2.5
757030063 63.5:1 7620/13200GY 120 0.3 W,X,M,Y 1.1 1.25 750 15 110 34 2.5
757030066 66.4:1 7968/13800GY 120 0.3 W,X,M,Y 1.1 1.25 750 15 110 34 2.5
757030067 66.67:1 8000/13856GY 120 0.3 W,X,M,Y 1.1 1.25 750 15 110 34 2.5
757030070 70:1 8400/14550GY 120 0.3 W,X,M,Y 1.1 1.25 750 15 110 34 2.5

URN-17 15 kV VOLTAGE TRANSFORMER


requirements.
Resin Gray* 132 21.6 13.9
8.07 (205) Nameplate

M12
8.6 (219)
19 (485)
H1
Lifting holes
3/4
2 holes to
conduit pipe
10 (254)
1 NPT
Drawing number:
Fused: 4286573
Unfused: 4286821

/4
1
CONNEC-
TIONS

H1 H2 H1 H2 H1 H2 H1 H2
MARKING
(Single
Fuse: 16A Fuse: 16A
Primary
Ratio)
X1 X2 X1 X2 X1 X2 X3 X1 X2 X3

Power-Frequency
Nominal
(Un) (Un)
(kVrms) (kVrms)
2400/4156GY 0.3 W,X/
757393060 20/60:1 120 1.1 1.5 1000 15 110 34 2.5
& 7200/12470GY 0.3 W,X,M,Y
0.3 W,X,M,Y/
757393113 66.26/112.88:1 7620/13200GY 115/67.5 1.1 1.5 1000 15 110 34 2.5
0.6 W,X,M,Y
2400/4156GY 0.3 W,X/
757396060 20/60:1 120 1.1 1.25 1500 15 110 34 2.5
& 7200/12470GY 0.3 W,X,M,Y
0.3 W,X,M,Y/
757396113 66.26/112.88:1 7620/13200GY 115/67.5 1.1 1.25 1500 15 110 34 2.5
0.6 W,X,M,Y
2400/4156GY 0.3 W,X/
757394060 20/60:1 120 1.1 1.5 1000 15 110 34 2.5
& 7200/12470GY 0.3 W,X,M,Y
0.3 W,X,M,Y/
757394113 66.26/112.88:1 7620/13200GY 115/67.5 1.1 1.5 1000 15 110 34 2.5
0.6 W,X,M,Y
2400/4156GY 0.3 W,X/
757398060 20/60:1 120 1.1 1.25 1500 15 110 34 2.5
& 7200/12470GY 0.3 W,X,M,Y
0.3 W,X,M,Y/
757398113 66.26/112.88:1 7620/13200GY 115/67.5 1.1 1.25 1500 15 110 34 2.5
0.6 W,X,M,Y
Notes:

VRJ-17 15 kV VOLTAGE TRANSFORMER


requirements.
Resin Gray* 97 21.2 10.82
11.81 (300) 8.26 (210) Nameplate
8.62 (219)
17.71 (450)
H1 H2 Lifting holes
3/4
2 holes to
conduit pipe
1 NPT 10 (254)
Drawing number:
Fused: 4286571
Unfused: 4286770

/4
1
CONNEC-
TIONS

H1 H2 H1 H2 H1 H2 H1 H2
MARKING
(Single
Fuse: 16A Fuse: 16A
Primary
Ratio) X1 X2 X1 X2 X1 X2 X3 X1 X2 X3

Power-Frequency
Nominal
Code * Primary Secondary IEEE Metering Voltage BIL
Ratio Voltage Factor Burden
(CEP) (V) (V) Accuracy System (kV) Primary & Secondary
Factor 30 s (VA)
(Un) (Un)
(kVrms) (kVrms)
757121020 20:1 2400/4160Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757121030 30:1 3600/3600Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757121035 35:1 4200/4200Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757121040 40:1 4800/4800Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757121060 60:1 7200/12470Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757121063 63.5:1 7620/13200Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757121070 70:1 8400/14550Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
8400/14550Y
757123121 70/121.21:1 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
& 14545/14545Y
757121100 100:1 12000/12000Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757121110 110:1 13200/13200Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757121120 120:1 14400/14400Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757129070 70:1 8400/14550Y 120 0.15 W,X 1.1 1.25 1000 15 110 34 2.5
757129100 100:1 12000/12000Y 120 0.15 W,X 1.1 1.25 1000 15 110 34 2.5
757129110 110:1 13200/13200Y 120 0.15 W,X 1.1 1.25 1000 15 110 34 2.5
757129120 120:1 14400/14400Y 120 0.15 W,X 1.1 1.25 1000 15 110 34 2.5
757125020 20:1 2400/4160Y 120 0.3 W,X,M,Y,Z 1.1 1.25 1500 15 110 34 2.5
757125030 30:1 3600/3600Y 120 0.3 W,X,M,Y,Z 1.1 1.25 1500 15 110 34 2.5
757125035 35:1 4200/4200Y 120 0.3 W,X,M,Y.Z 1.1 1.25 1500 15 110 34 2.5
757125040 40:1 4800/4800Y 120 0.3 W,X,M,Y,Z 1.1 1.25 1500 15 110 34 2.5
757125060 60:1 7200/12470Y 120 0.3 W,X,M,Y,Z 1.1 1.25 1500 15 110 34 2.5
757125063 63.5:1 7620/13200Y 120 0.3 W,X,M,Y,Z 1.1 1.25 1500 15 110 34 2.5
757125070 70:1 8400/14550Y 120 0.3 W,X,M,Y,Z 1.1 1.25 1500 15 110 34 2.5
8400/14550Y
757126121 70/121.21:1 120 0.3 W,X,M,Y,Z 1.1 1.25 1500 15 110 34 2.5
& 14545/14545Y
757125100 100:1 12000/12000Y 120 0.3 W,X,M,Y,Z 1.1 1.25 1500 15 110 34 2.5
757125110 110:1 13200/13200Y 120 0.3 W,X,M,Y,Z 1.1 1.25 1500 15 110 34 2.5
757125120 120:1 14400/14400Y 120 0.3 W,X,M,Y,Z 1.1 1.25 1500 15 110 34 2.5
757126070 70:1 8400/14550Y 120 0.15 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757126100 100:1 12000/12000Y 120 0.15 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757126110 110:1 13200/13200Y 120 0.15 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757126120 120:1 14400/14400Y 120 0.15 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5

Power-Frequency
Nominal
Factor 30 s (VA)
(Un) (Un)
(kVrms) (kVrms)
757124020 20:1 2400/4160Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757124030 30:1 3600/3600Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757124035 35:1 4200/4200Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757124040 40:1 4800/4800Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757124060 60:1 7200/12470Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757124063 63.5:1 7620/13200Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757124070 70:1 8400/14550Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757124100 100:1 12000/12000Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757124110 110:1 13200/13200Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757124120 120:1 14400/14400Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757120020 20:1 2400/4160Y 120 0.3 W,X,M,Y,Z 1.1 1.25 1500 15 110 34 2.5
757120030 30:1 3600/3600Y 120 0.3 W,X,M,Y,Z 1.1 1.25 1500 15 110 34 2.5
757120035 35:1 4200/4200Y 120 0.3 W,X,M,Y.Z 1.1 1.25 1500 15 110 34 2.5
757120040 40:1 4800/4800Y 120 0.3 W,X,M,Y,Z 1.1 1.25 1500 15 110 34 2.5
757120060 60:1 7200/12470Y 120 0.3 W,X,M,Y,Z 1.1 1.25 1500 15 110 34 2.5
757120063 63.5:1 7620/13200Y 120 0.3 W,X,M,Y,Z 1.1 1.25 1500 15 110 34 2.5
757120070 70:1 8400/14550Y 120 0.3 W,X,M,Y,Z 1.1 1.25 1500 15 110 34 2.5
757120100 100:1 12000/12000Y 120 0.3 W,X,M,Y,Z 1.1 1.25 1500 15 110 34 2.5
757120110 110:1 13200/13200Y 120 0.3 W,X,M,Y,Z 1.1 1.25 1500 15 110 34 2.5
757120120 120:1 14400/14400Y 120 0.3 W,X,M,Y,Z 1.1 1.25 1500 15 110 34 2.5

Notes:



requirements.
Resin Gray* 83.7 21.2 10.23
11.42 (290) 8.03 (204)

Nameplate
M12
8.62 (219)
17.7 (450)
H1 H2
Lifting holes
3/4
2 holes to
conduit pipe
1 NPT 10 (254)
Drawing number:
Fused: 4286569
Unfused: 4286774

/4
1
CONNEC-
TIONS

SINGLE SECONDARY
H1 H2 H1 H2
MARKING
(Single
Fuse: 16A
Primary
Ratio) X1 X2 X1 X2
FUSED UNFUSED

Power-Frequency
Nominal
(Un) (Un)
(kVrms) (kVrms)
757021020 20:1 2400/4160Y 120 0.3 W,X,M,Y 1.1 1.25 750 15 110 34 2.5
757021035 35:1 4200/4200Y 120 0.3 W,X,M,Y 1.1 1.25 750 15 110 34 2.5
757021040 40:1 4800/4800Y 120 0.3 W,X,M,Y 1.1 1.25 750 15 110 34 2.5
757021042 42:1 5040/5040Y 120 0.3 W,X,M,Y 1.1 1.25 750 15 110 34 2.5
757021060 60:1 7200/12470Y 120 0.3 W,X,M,Y 1.1 1.25 750 15 110 34 2.5
757021063 63.5:1 7620/13200Y 120 0.3 W,X,M,Y 1.1 1.25 750 15 110 34 2.5
757021066 66:1 7920/13700Y 120 0.3 W,X,M,Y 1.1 1.25 750 15 110 34 2.5
757021070 70:1 8400/14550Y 120 0.3 W,X,M,Y 1.1 1.25 750 15 110 34 2.5
757021100 100:1 12000/12000Y 120 0.3 W,X,M,Y 1.1 1.25 750 15 110 34 2.5
757021110 110:1 13200/13200Y 120 0.3 W,X,M,Y 1.1 1.25 750 15 110 34 2.5
757021115 115:1 13800/13800Y 120 0.3 W,X,M,Y 1.1 1.25 750 15 110 34 2.5
757021120 120:1 14400/14400Y 120 0.3 W,X,M,Y 1.1 1.25 750 15 110 34 2.5
757025020 20:1 2400/4160Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757025035 35:1 4200/4200Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757025040 40:1 4800/4800Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757025042 42:1 5040/5040Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757025060 60:1 7200/12470Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757025063 63.5:1 7620/13200Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757025066 66:1 7920/13700Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757025070 70:1 8400/14550Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757025100 100:1 12000/12000Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757025110 110:1 13200/13200Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757025115 115:1 13800/13800Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757025120 120:1 14400/14400Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5

Power-Frequency
Nominal
(Un) (Un)
(kVrms) (kVrms)
757024020 20:1 2400/4160Y 120 0.3 W,X,M,Y 1.1 1.25 750 15 110 34 2.5
757024035 35:1 4200/4200Y 120 0.3 W,X,M,Y 1.1 1.25 750 15 110 34 2.5
757024040 40:1 4800/4800Y 120 0.3 W,X,M,Y 1.1 1.25 750 15 110 34 2.5
757024042 42:1 5040/5040Y 120 0.3 W,X,M,Y 1.1 1.25 750 15 110 34 2.5
757024060 60:1 7200/12470Y 120 0.3 W,X,M,Y 1.1 1.25 750 15 110 34 2.5
757024063 63.5:1 7620/13200Y 120 0.3 W,X,M,Y 1.1 1.25 750 15 110 34 2.5
757024066 66:1 7920/13700Y 120 0.3 W,X,M,Y 1.1 1.25 750 15 110 34 2.5
757024070 70:1 8400/14550Y 120 0.3 W,X,M,Y 1.1 1.25 750 15 110 34 2.5
757024100 100:1 12000/12000Y 120 0.3 W,X,M,Y 1.1 1.25 750 15 110 34 2.5
757024110 110:1 13200/13200Y 120 0.3 W,X,M,Y 1.1 1.25 750 15 110 34 2.5
757024115 115:1 13800/13800Y 120 0.3 W,X,M,Y 1.1 1.25 750 15 110 34 2.5
757024120 120:1 14400/14400Y 120 0.3 W,X,M,Y 1.1 1.25 750 15 110 34 2.5
757020020 20:1 2400/4160Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757020035 35:1 4200/4200Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757020040 40:1 4800/4800Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757020042 42:1 5040/5040Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757020060 60:1 7200/12470Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757020063 63.5:1 7620/13200Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757020066 66:1 7920/13700Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757020070 70:1 8400/14550Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757020100 100:1 12000/12000Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757020110 110:1 13200/13200Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757020115 115:1 13800/13800Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757020120 120:1 14400/14400Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5

Notes:

VRN-17 15 kV VOLTAGE TRANSFORMER


requirements.
Resin Gray* 136.4 21.2 8.8
11.81 (300) 8.07 (205) Nameplate

M12
8.6 (219)
19 (485)
H1 H2
Lifting holes
3/4
2 holes to
conduit pipe
1 NPT
10 (254)
Drawing number:
Fused: 4286575
Unfused: 4286822

/4
1
CONNEC-
TIONS

H1 H2 H1 H2 H1 H2 H1 H2
MARKING
(Single
Fuse: 16A Fuse: 16A
Primary
Ratio)
X1 X2 X1 X2 X1 X2 X3 X1 X2 X3

Power-Frequency
Nominal
(Un) (Un)
(kVrms) (kVrms)
757101020 20:1 2400/4160Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757101030 30:1 3600/3600Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757101035 35:1 4200/4200Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757101040 40:1 4800/4800Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757101060 60:1 7200/12470Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757101063 63.5:1 7620/13200Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757101070 70:1 8400/14550Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
8400/14550Y
757103121 70/121.2:1 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
& 14545/14545Y
757101100 100:1 12000/12000Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757101110 110:1 13200/13200Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757101120 120:1 14400/14400Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757105020 20:1 2400/4160Y 120 0.3 W,X,M,Y,Z 1.1 1.25 1500 15 110 34 2.5
757105030 30:1 3600/3600Y 120 0.3 W,X,M,Y,Z 1.1 1.25 1500 15 110 34 2.5
757105035 35:1 4200/4200Y 120 0.3 W,X,M,Y,Z 1.1 1.25 1500 15 110 34 2.5
757105040 40:1 4800/4800Y 120 0.3 W,X,M,Y,Z 1.1 1.25 1500 15 110 34 2.5
757105060 60:1 7200/12470Y 120 0.3 W,X,M,Y,Z 1.1 1.25 1500 15 110 34 2.5
757105063 63.5:1 7620/13200Y 120 0.3 W,X,M,Y,Z 1.1 1.25 1500 15 110 34 2.5
757105070 70:1 8400/14550Y 120 0.3 W,X,M,Y,Z 1.1 1.25 1500 15 110 34 2.5
8400/14550Y
757106121 70/121.2:1 120 0.3 W,X,M,Y,Z 1.1 1.25 1500 15 110 34 2.5
& 14545/14545Y
757105100 100:1 12000/12000Y 120 0.3 W,X,M,Y,Z 1.1 1.25 1500 15 110 34 2.5
757105110 110:1 13200/13200Y 120 0.3 W,X,M,Y,Z 1.1 1.25 1500 15 110 34 2.5
757105120 120:1 14400/14400Y 120 0.3 W,X,M,Y,Z 1.1 1.25 1500 15 110 34 2.5
757104020 20:1 2400/4160Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757104030 30:1 3600/3600Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757104035 35:1 4200/4200Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757104040 40:1 4800/4800Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757104060 60:1 7200/12470Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757104063 63.5:1 7620/13200Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757104070 70:1 8400/14550Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757104100 100:1 12000/12000Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757104110 110:1 13200/13200Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757104120 120:1 14400/14400Y 120 0.3 W,X,M,Y 1.1 1.25 1000 15 110 34 2.5
757100020 20:1 2400/4160Y 120 0.3 W,X,M,Y,Z 1.1 1.25 1500 15 110 34 2.5
757100030 30:1 3600/3600Y 120 0.3 W,X,M,Y,Z 1.1 1.25 1500 15 110 34 2.5
757100035 35:1 4200/4200Y 120 0.3 W,X,M,Y,Z 1.1 1.25 1500 15 110 34 2.5
757100040 40:1 4800/4800Y 120 0.3 W,X,M,Y,Z 1.1 1.25 1500 15 110 34 2.5
757100060 60:1 7200/12470Y 120 0.3 W,X,M,Y,Z 1.1 1.25 1500 15 110 34 2.5
757100063 63.5:1 7620/13200Y 120 0.3 W,X,M,Y,Z 1.1 1.25 1500 15 110 34 2.5
757100070 70:1 8400/14550Y 120 0.3 W,X,M,Y,Z 1.1 1.25 1500 15 110 34 2.5
757100100 100:1 12000/12000Y 120 0.3 W,X,M,Y,Z 1.1 1.25 1500 15 110 34 2.5
757100110 110:1 13200/13200Y 120 0.3 W,X,M,Y,Z 1.1 1.25 1500 15 110 34 2.5
757100120 120:1 14400/14400Y 120 0.3 W,X,M,Y,Z 1.1 1.25 1500 15 110 34 2.5
* For HCEP Option add (H) to the end of the code number. Additional ratings available upon request.



requirements.
Resin Gray* 93
12.99 (330) 8.27 (210)

M12 Nameplate
8.62 (219)
21 (533.4)
Lifting holes
3/4
2 holes to
conduit pipe
10 (254)
1 NPT
Drawing number:
Fused: 4286593
Unfused: 4286823

/4
1
CONNEC-
TIONS

SINGLE SECONDARY
H1 H2 H1 H2
MARKING
(Single
Fuse: 16A
Primary
Ratio)
X1 X2 X1 X2
FUSED UNFUSED

Power-Frequency
Nominal
(Un) (Un)
(kVrms) (kVrms)
757071060 60:1 7200/12470GY 120 0.3 W,X,M,Y 1.1 1.25 1000 25 150 50 2.5
757071100 100:1 12000/20780GY 120 0.3 W,X,M,Y 1.1 1.25 1000 25 150 50 2.5
757079100 100:1 12000/20780GY 120 0.15 W,X 1.1 1.25 1000 25 150 50 2.5
757071110 110:1 13200/22860GY 120 0.3 W,X,M,Y 1.1 1.25 1000 25 150 50 2.5
757079110 110:1 13200/22863GY 120 0.15 W,X 1.1 1.25 1000 25 150 50 2.5
757071120 120:1 14400/24940GY 120 0.3 W,X,M,Y 1.1 1.25 1000 25 150 50 2.5
757079120 120:1 14400/24250GY 120 0.15 W,X 1.1 1.25 1000 25 150 50 2.5
757071150 150:1 18000/18000GY 120 0.3 W,X,M,Y 1.1 1.25 1000 25 150 50 2.5
757079150 150:1 18000/18000GY 120 0.15 W,X 1.1 1.25 1000 25 150 50 2.5
757071200 200:1 24000 /24000GY 120 0.3 W,X,M,Y 1.1 1.25 1000 25 150 50 2.5
757079200 200:1 24000 /24000GY 120 0.15 W,X 1.1 1.25 1000 25 150 50 2.5
757070060 60:1 7200/12470GY 120 0.3 W,X,M,Y 1.1 1.25 1000 25 150 50 2.5
757070100 100:1 12000/20780GY 120 0.3 W,X,M,Y 1.1 1.25 1000 25 150 50 2.5
757070110 110:1 13200/22860GY 120 0.3 W,X,M,Y 1.1 1.25 1000 25 150 50 2.5
757070120 120:1 14400/24940GY 120 0.3 W,X,M,Y 1.1 1.25 1000 25 150 50 2.5
757070150 150:1 18000/18000GY 120 0.3 W,X,M,Y 1.1 1.25 1000 25 150 50 2.5
757070200 200:1 24000 /24000GY 120 0.3 W,X,M,Y 1.1 1.25 1000 25 150 50 2.5
Notes:



requirements.
Resin Gray* 136.4 27.5 14.69
14.96 (380) 8.07 (205)

M12 Nameplate
8.6 (219)
20.86 (530)
H1
Lifting holes
3/4
2 holes to
conduit pipe
10 (254)
1 NPT
Drawing number:
Fused: 4286576
Unfused: 4286772

/4
1
CONNEC-
TIONS

H1 H2 H1 H2 H1 H2 H1 H2
MARKING
(Single
Fuse: 16A Fuse: 16A
Primary
Ratio)
X1 X2 X1 X2 X1 X2 X3 X1 X2 X3

Power-Frequency
Nominal
(Un) (Un)
(kVrms) (kVrms)
757441100 100:1 12000/20784GY 120 0.3 W,X,M,Y 1.1 1.5 1000 25 150 50 2.5
757441110 110:1 13200/22863GY 120 0.3 W,X,M,Y 1.1 1.5 1000 25 150 50 2.5
757441120 120:1 14400/24940GY 120 0.3 W,X,M,Y 1.1 1.5 1000 25 150 50 2.5
7200/12470GY & 0.3 W,X /
757443120 60/120:1 120 1.1 1.5 1000 25 150 50 2.5
14400/24940GY 0.3W,X,M,Y
757443200 120/200:1 14400/24940GY 120/72 0.3 W,X,M,Y 1.1 1.5 1000 25 150 50 2.5
757445100 100:1 12000/20784GY 120 0.3 W,X,M,Y 1.1 1.25 1500 25 150 50 2.5
757445110 110:1 13200/22863GY 120 0.3 W,X,M,Y 1.1 1.25 1500 25 150 50 2.5
757445120 120:1 14400/24940GY 120 0.3 W,X,M,Y 1.1 1.25 1500 25 150 50 2.5
7200/12470GY & 0.3 W,X /
757446120 60/120:1 120 1.1 1.25 1500 25 150 50 2.5
14400/24940GY 0.3W,X,M,Y
757446200 120/200:1 14400/24940GY 120/72 0.3 W,X,M,Y 1.1 1.25 1500 25 150 50 2.5
757444100 100:1 12000/20784GY 120 0.3 W,X,M,Y 1.1 1.5 1000 25 150 50 2.5
757444110 110:1 13200/22863GY 120 0.3 W,X,M,Y 1.1 1.5 1000 25 150 50 2.5
757444120 120:1 14400/24940GY 120 0.3 W,X,M,Y 1.1 1.5 1000 25 150 50 2.5
757444200 120/200:1 14400/24940GY 120/72 0.3 W,X,M,Y 1.1 1.5 1000 25 150 50 2.5
757440100 100:1 12000/20784GY 120 0.3 W,X,M,Y 1.1 1.25 1500 25 150 50 2.5
757440110 110:1 13200/22863GY 120 0.3 W,X,M,Y 1.1 1.25 1500 25 150 50 2.5
757440120 120:1 14400/24940GY 120 0.3 W,X,M,Y 1.1 1.25 1500 25 150 50 2.5
757448200 120/200:1 14400/24940GY 120/72 0.3 W,X,M,Y 1.1 1.25 1500 25 150 50 2.5
Notes:



requirements.
Resin Gray* 99 33.46 10.63
12.6 (320)
M12
8.62 (219)
20.27 (515)
2 holes to
conduit pipe
1 NPT 10 (254)
Drawing number:
Fused: 4286574
Unfused: 4286824

/4
1
CONNEC-
TIONS

SINGLE SECONDARY
H1 H2 H1 H2
MARKING
(Single
Fuse: 16A
Primary
Ratio)
X1 X2 X1 X2
FUSED UNFUSED

Power-Frequency
Nominal
(Un) (Un)
(kVrms) (kVrms)
757141060 60:1 7200/12470Y 120 0.3 W,X,M,Y 1.1 1.25 1000 25 150 50 2.5
757141100 100:1 12000/20780Y 120 0.3 W,X,M,Y 1.1 1.25 1000 25 150 50 2.5
757149100 100:1 12000/20780Y 120 0.15 W,X 1.1 1.25 1000 25 150 50 2.5
757141110 110:1 13200/22860Y 120 0.3 W,X,M,Y 1.1 1.25 1000 25 150 50 2.5
757149110 110:1 13200/22860Y 120 0.15 W,X 1.1 1.25 1000 25 150 50 2.5
757141120 120:1 14400/24940Y 120 0.3 W,X,M,Y 1.1 1.25 1000 25 150 50 2.5
757149120 120:1 14400/24250Y 120 0.15 W,X 1.1 1.25 1000 25 150 50 2.5
757141150 150:1 18000/18000Y 120 0.3 W,X,M,Y 1.1 1.25 1000 25 150 50 2.5
757149150 150:1 18000/18000Y 120 0.15 W,X 1.1 1.25 1000 25 150 50 2.5
757141200 200:1 24000 /24000Y 120 0.3 W,X,M,Y 1.1 1.25 1000 25 150 50 2.5
757149200 200:1 24000 /24000Y 120 0.15 W,X 1.1 1.25 1000 25 150 50 2.5
757140060 60:1 7200/12470Y 120 0.3 W,X,M,Y 1.1 1.25 1000 25 150 50 2.5
757140100 100:1 12000/20780Y 120 0.3 W,X,M,Y 1.1 1.25 1000 25 150 50 2.5
757140110 110:1 13200/22860Y 120 0.3 W,X,M,Y 1.1 1.25 1000 25 150 50 2.5
757140120 120:1 14400/24940Y 120 0.3 W,X,M,Y 1.1 1.25 1000 25 150 50 2.5
757140150 150:1 18000/18000Y 120 0.3 W,X,M,Y 1.1 1.25 1000 25 150 50 2.5
757140200 200:1 24000 /24000Y 120 0.3 W,X,M,Y 1.1 1.25 1000 25 150 50 2.5
Notes:



requirements.
Resin Gray* 140 31.88 10.82
12.4 (315) 8.07 (205) Nameplate

M12
8.6 (219)
20.74 (527)
H1 H2 Lifting holes
3/4
2 holes to
conduit pipe
1 NPT 10 (254)
Drawing number:
Fused: 4286577
Unfused: 4286771

/4
1
CONNEC-
TIONS

H1 H2 H1 H2 H1 H2 H1 H2
MARKING
(Single
Fuse: 16A Fuse: 16A
Primary
Ratio)
X1 X2 X1 X2 X1 X2 X3 X1 X2 X3

Power-Frequency
Nominal
(Un) (Un)
(kVrms) (kVrms)
757201060 60:1 7200/12470Y 120 0.3 W,X,M,Y 1.1 1.25 1000 25 150 50 2.5
7200/12470Y & 0.3 W,X /
757203120 60/120:1 120 1.1 1.25 1000 25 150 50 2.5
14400/24940Y 0.3W,X,M,Y
757201100 100:1 12000/20780Y 120 0.3 W,X,M,Y 1.1 1.25 1000 25 150 50 2.5
757201110 110:1 13200/22860Y 120 0.3 W,X,M,Y 1.1 1.25 1000 25 150 50 2.5
757201120 120:1 14400/24940Y 120 0.3 W,X,M,Y 1.1 1.25 1000 25 150 50 2.5
0.3 W,X,M,Y /
757203200 120/200:1 14400/24250Y 120/72 1.1 1.25 1000 25 150 50 2.5
0.3 W,X,M,Y
757201150 150:1 18000/18000Y 120 0.3 W,X,M,Y 1.1 1.25 1000 25 150 50 2.5
757201200 200:1 24000 /24000Y 120 0.3 W,X,M,Y 1.1 1.25 1000 25 150 50 2.5
757209100 100:1 12000/20780Y 120 0.15 W,X 1.1 1.25 1000 25 150 50 2.5
757209110 110:1 13200/22860Y 120 0.15 W,X 1.1 1.25 1000 25 150 50 2.5
757209120 120:1 14400/24250Y 120 0.15 W,X 1.1 1.25 1000 25 150 50 2.5
757209150 150:1 18000/18000Y 120 0.15 W,X 1.1 1.25 1000 25 150 50 2.5
757209200 200:1 24000 /24000Y 120 0.15 W,X 1.1 1.25 1000 25 150 50 2.5
757205060 60:1 7200/12470Y 120 0.3 W,X,M,Y 1.1 1.25 1500 25 150 50 2.5
7200/12470Y & 0.3 W,X /
757206120 60/120:1 120 1.1 1.25 1500 25 150 50 2.5
14400/24940Y 0.3W,X,M,Y
757205100 100:1 12000/20780Y 120 0.3 W,X,M,Y 1.1 1.25 1500 25 150 50 2.5
757205110 110:1 13200/22860Y 120 0.3 W,X,M,Y 1.1 1.25 1500 25 150 50 2.5
757205120 120:1 14400/24940Y 120 0.3 W,X,M,Y 1.1 1.25 1500 25 150 50 2.5
0.3 W,X,M,Y /
757206200 120/200:1 14400/24250Y 120/72 1.1 1.25 1500 25 150 50 2.5
0.3 W,X,M,Y
757205150 150:1 18000/18000Y 120 0.3 W,X,M,Y 1.1 1.25 1500 25 150 50 2.5
757205200 200:1 24000 /24000Y 120 0.3 W,X,M,Y 1.1 1.25 1500 25 150 50 2.5
757206100 100:1 12000/20780Y 120 0.15 W,X 1.1 1.25 1500 25 150 50 2.5
757206110 110:1 13200/22860Y 120 0.15 W,X 1.1 1.25 1500 25 150 50 2.5
757206150 150:1 18000/18000Y 120 0.15 W,X 1.1 1.25 1500 25 150 50 2.5
757204060 60:1 7200/12470Y 120 0.3 W,X,M,Y 1.1 1.25 1000 25 150 50 2.5
757204100 100:1 12000/20780Y 120 0.3 W,X,M,Y 1.1 1.25 1000 25 150 50 2.5
757204110 110:1 13200/22860Y 120 0.3 W,X,M,Y 1.1 1.25 1000 25 150 50 2.5
757204120 120:1 14400/24940Y 120 0.3 W,X,M,Y 1.1 1.25 1000 25 150 50 2.5
757204150 150:1 18000/18000Y 120 0.3 W,X,M,Y 1.1 1.25 1000 25 150 50 2.5
757204200 200:1 24000/24000Y 120 0.3 W,X,M,Y 1.1 1.25 1000 25 150 50 2.5
757200060 60:1 7200/12470Y 120 0.3 W,X,M,Y 1.1 1.25 1500 25 150 50 2.5
757200100 100:1 12000/20780Y 120 0.3 W,X,M,Y 1.1 1.25 1500 25 150 50 2.5
757200110 110:1 13200/22860Y 120 0.3 W,X,M,Y 1.1 1.25 1500 25 150 50 2.5
757200120 120:1 14400/24940Y 120 0.3 W,X,M,Y 1.1 1.25 1500 25 150 50 2.5
757200150 150:1 18000/18000Y 120 0.3 W,X,M,Y 1.1 1.25 1500 25 150 50 2.5
757200200 200:1 24000/24000Y 120 0.3 W,X,M,Y 1.1 1.25 1500 25 150 50 2.5

URS-36 34.5 kV VOLTAGE TRANSFORMER


requirements.
Resin Gray* 174 49.6 25.2
9.4 (240)
M12
7.87 (200)
28.14 (714.75)
H1
Lifting holes
3/4
2 holes to
conduit pipe 13.7 (350)
1 NPT
Drawing number:
Fused: 4286578
Unfused: 4286773

/4
1
CONNEC-
TIONS

H1 H2 H1 H2 H1 H2 H1 H2
MARKING
(Single
Fuse: 16A Fuse: 16A
Primary
Ratio)
X1 X2 X1 X2 X1 X2 X3 X1 X2 X3

URS-36 34.5 kV VOLTAGE TRANSFORMER
Power-Frequency
Nominal
(Un) (Un)
(kVrms) (kVrms)
757861140 140:1 16800/29098GY 120 0.3 W,X,M,Y 1.1 1.73 1000 34.5 200 70 2.5
757863240 140/240:1 16100/27886GY 115/67.08 0.3 W,X,M,Y 1.1 1.73 1000 34.5 200 70 2.5
757861166 166:1 19920/34500GY 120 0.3 W,X,M,Y 1.1 1.73 1000 34.5 200 70 2.5
757861175 175:1 20125/34857GY 115 0.3 W,X,M,Y 1.1 1.73 1000 34.5 200 70 2.5
757863300 175/300:1 20125/34857GY 115/67.08 0.3 W,X,M,Y 1.1 1.73 1000 34.5 200 70 2.5
757860140 140:1 16800/29098GY 120 0.3 W,X,M,Y 1.1 1.73 1000 34.5 200 70 2.5
757868240 140/240:1 16100/27886GY 115/67.08 0.3 W,X,M,Y 1.1 1.73 1000 34.5 200 70 2.5
757860166 166:1 19920/34500GY 120 0.3 W,X,M,Y 1.1 1.73 1000 34.5 200 70 2.5
757860175 175:1 20125/34857GY 115 0.3 W,X,M,Y 1.1 1.73 1000 34.5 200 70 2.5
757868300 175/300:1 20125/34857GY 115/67.08 0.3 W,X,M,Y 1.1 1.73 1000 34.5 200 70 2.5
Notes:

VRS-36 34.5 kV VOLTAGE TRANSFORMER


requirements.
Resin Gray* 183 49.2 183
19.68 (500) 9.4 (240)

M12 Nameplate
7.87 (200)
27.36 (695)
Lifting holes
H1 H2 3/4
2 holes to
conduit pipe
13.7 (350)
1 NPT
Drawing number:
Fused: 4286579
Unfused: 4286825

/4
1
CONNEC-
TIONS

H1 H2 H1 H2 H1 H2 H1 H2
MARKING
(Single
Fuse: 16A Fuse: 16A
Primary
Ratio)
X1 X2 X1 X2 X1 X2 X3 X1 X2 X3

VRS-36 34.5 kV VOLTAGE TRANSFORMER
Power-Frequency
Nominal
(Un) (Un)
(kVrms) (kVrms)
69.25 / 8310/14393Y &
757923166 120 0.3 W,X,M,Y 1.1 1.25 1000 34.5 200 70 2.5
166:1 19920/34500Y
757921140 140:1 16800/29098Y 120 0.3 W,X,M,Y 1.1 1.25 1000 34.5 200 70 2.5
757923240 140/240:1 16100/27886Y 115/67.08 0.3 W,X,M,Y 1.1 1.25 1000 34.5 200 70 2.5
757921166 166:1 19920/34500Y 120 0.3 W,X,M,Y 1.1 1.25 1000 34.5 200 70 2.5
757921175 175:1 20125/34857Y 115 0.3 W,X,M,Y 1.1 1.25 1000 34.5 200 70 2.5
757923300 175/300:1 20125/34857Y 115/67.08 0.3 W,X,M,Y 1.1 1.25 1000 34.5 200 70 2.5
757921220 220:1 26400/26400Y 120 0.3 W,X,M,Y,Z 1.1 1.25 1000 34.5 200 70 2.5
757923400 240/400:1 27600/27600Y 115 / 69 0.3 W,X,M,Y 1.1 1.25 1000 34.5 200 70 2.5
757921300 300:1 34500/34500Y 115 0.3 W,X,M,Y,Z 1.1 1.25 1000 34.5 200 70 2.5
757923500 300/500:1 34500/34500Y 115/69 0.3 W,X,M,Y 1.1 1.25 1000 34.5 200 70 2.5
757929140 140:1 16800/29098Y 120 0.15 W,X 1.1 1.25 1000 34.5 200 70 2.5
757929166 166:1 19920/34500Y 120 0.15 W,X 1.1 1.25 1000 34.5 200 70 2.5
757929175 175:1 20125/34500Y 115 0.15 W,X 1.1 1.25 1000 34.5 200 70 2.5
757929200 200:1 26400/26400Y 115 0.15 W,X 1.1 1.25 1000 34.5 200 70 2.5
757929300 300:1 34500/34500Y 115 0.15 W,X 1.1 1.25 1000 34.5 200 70 2.5
69.25 / 8310/14393Y &
757928166 120 0.3 W,X,M,Y 1.1 1.25 1000 34.5 200 70 2.5
166:1 19920/34500Y
757920140 140:1 16800/29098Y 120 0.3 W,X,M,Y 1.1 1.25 1000 34.5 200 70 2.5
757928240 140/240:1 16100/27886Y 115/67.08 0.3 W,X,M,Y 1.1 1.25 1000 34.5 200 70 2.5
757920166 166:1 19920/34500Y 120 0.3 W,X,M,Y 1.1 1.25 1000 34.5 200 70 2.5
757920175 175:1 20125/34857Y 115 0.3 W,X,M,Y 1.1 1.25 1000 34.5 200 70 2.5
757928300 175/300:1 20125/34857Y 115/67.08 0.3 W,X,M,Y 1.1 1.25 1000 34.5 200 70 2.5
757920220 220:1 26400/26400Y 120 0.3 W,X,M,Y,Z 1.1 1.25 1000 34.5 200 70 2.5
757928400 240/400:1 27600/27600Y 115 / 69 0.3 W,X,M,Y 1.1 1.25 1000 34.5 200 70 2.5
757920300 300:1 34500/34500Y 115 0.3 W,X,M,Y,Z 1.1 1.25 1000 34.5 200 70 2.5
757928500 300/500:1 34500/34500Y 115/69 0.3 W,X,M,Y 1.1 1.25 1000 34.5 200 70 2.5
Notes:

URU-52 46 kV VOLTAGE TRANSFORMER


requirements.
Resin Gray* 374 64.56 38.58
17.12 (435)
M12
15.74 (400)
40.55 (1030)
H1
19.68 (500)

/4
1
CONNEC-
TIONS

ONE TWO
ONE TWO
WITH TAP WITH TAP
MARKING H1 H2 H1 H2 H1 H2 H1 H2
(Single
Primary
Y1 Y2 Y1 Y2 Y3

Power-Frequency
Nominal
Factor 30 s (VA)
(Un) (Un)
(kVrms) (kVrms)
757971240 240:1 27600/47804GY 115 0.3 W,X,M,Y,Z,ZZ 1.1 1.73 2500 46 250 95 2.5
0.3 W,X,M,Y,Z 1250 &
757972240 240 & 240:1 27600/47804GY 115 & 115 1.1 1.73 46 250 95 2.5
& 0.3 W,X,M,Y,Z 1250
757973400 240/400:1 27600/47804GY 115/69 0.3 W,X,M,Y,Z 1.1 1.73 2500 46 250 95 2.5
757979240 240:1 27600/47804GY 115 0.15 W,X,M,Y,Z 1.1 1.73 2500 46 250 95 2.5
240/400 115/69 & 0.3 W,X,M,Y,Z 1250 &
757972400 27600/47804GY 1.1 1.73 46 250 95 2.5
& 240/400:1 115/69 & 0.3 W,X,M,Y,Z 1250
Notes:

VRU-52 46 kV VOLTAGE TRANSFORMER


requirements.
Resin Gray* 394 61.41 24
24 (610) 17.12 (435)

M12
15.74 (400)
38.81 (986)
H1 H2
19.68 (500)

/4
1
CONNEC-
TIONS

ONE TWO
ONE TWO
WITH TAP WITH TAP
(Single
Primary
Y1 Y2 Y1 Y2 Y3

Power-Frequency
Nominal
Factor 30 s (VA)
(Un) (Un)
(kVrms) (kVrms)
757981240 240:1 27600/47804Y 115 0.3 W,X,M,Y,Z,ZZ 1.1 1.25 3000 46 250 95 2.5
0.3 W,X,M,Y,Z & 1500 &
757982240 240 & 240:1 27600/47804Y 115 & 115 1.1 1.25 46 250 95 2.5
0.3 W,X,M,Y,Z 1500
757983400 240/400:1 27600/47804Y 115/69 0.3 W,X,M,Y,Z 1.1 1.25 3000 46 250 95 2.5
757981400 400:1 46000/46000Y 115 0.3 W,X,M,Y,Z,ZZ 1.1 1.25 3000 46 250 95 2.5
0.3 W,X,M,Y,Z & 1500 &
757982400 400 & 400:1 46000/46000Y 115 & 115 1.1 1.25 46 250 95 2.5
0.3 W,X,M,Y,Z 1500
757983666 400/666.66:1 46000/46000Y 115/69 0.3 W,X,M,Y,Z 1.1 1.25 3000 46 250 95 2.5
757989240 240:1 27600/47804Y 115 0.15 W,X,M,Y,Z 1.1 1.25 3000 46 250 95 2.5
757986400 240/400:1 27600/47804Y 115/69 0.15 W,X,M,Y 1.1 1.25 3000 46 250 95 2.5
757989400 400:1 46000/46000Y 115 0.15 W,X,M,Y,Z 1.1 1.25 3000 46 250 95 2.5
Notes:



requirements.
Resin Gray* 381.4 92.91 43.3
Primary terminal pad 17.12 (435)

NEMA 4 STD
Thread 1/2
Connector
TE-250
15.74 (400)
48.34 (1228)
Lifting holes
3/4
H1
2 holes to
conduit pipe
1 NPT Nameplate 19.68 (500)
PRIMARY TERMINAL GROUND TERMINAL
Type: TE-250 Type: NEMA-2 Type: NEMA-4 Type: TE-12-250

Material: Copper Material: Copper Material: Copper Material: Copper
Range: 2/0 TRE-250MCM Range: 4TRE-250MCM
CONNEC-
TIONS
SECONDARY ONE TWO

ONE TWO
TERMINAL SECONDARY SECONDARIES
WITH TAP WITH TAP
4
/
1
(Single
Primary
Y1 Y2 Y1 Y2 Y3
Material: Brass

Power-Frequency
Nominal
(Un) (Un)
(kVrms) (kVrms)
40250/
757551350 350:1 115 0.3 W,X,M,Y,ZZ 1.1 1.73 2500 69 350 140 2.5
69000GY
40250/
757553600 350/600:1 115/67.08 0.3 W,X,M,Y,Z 1.1 1.73 2500 69 350 140 2.5
69000GY
350/600 40250/ 115/67.08 & 0.3 W,X,M,Y,Z &
757552600 1.1 1.73 1250 & 1250 69 350 140 2.5
&350/600:1 69000GY 115/67.08 0.3 W,X,M,Y,Z
Notes:



requirements.
Resin Gray* 455.5 86.5 29
17.32 (440)
38 (965.2)
17.13 (435)
15.75 (400)
43.88 (1114.5)
19.69 (500)
PRIMARY TERMINAL GROUND TERMINAL
Type: TE-250 Type: NEMA-2 Type: NEMA-4 Type: TE-12-250

Material: Copper Material: Copper Material: Copper Material: Copper
Range: 2/0 TRE-250MCM Range: 4TRE-250MCM
CONNEC-
TIONS
SECONDARY ONE TWO

ONE TWO
TERMINAL SECONDARY SECONDARIES
WITH TAP WITH TAP
4
/
1
(Single
Primary
Y1 Y2 Y1 Y2 Y3
Material: Brass

Power-Frequency
Nominal
Factor 30 s (VA)
(Un) (Un)
(kVrms) (kVrms)
757561600 600:1 69000/69000Y 115 0.3 W,X,M,X,Y,Z,ZZ 1.1 1.73 4000 69 350 140 2.5
350/600 & 40250/69000Y or 197/115 & 0.3 W,X,M,X,Y,Z & 2000 &
757563600 1.1 1.73 69 350 140 2.5
350/600:1 69000/69000Y 115/67.08 0.3 W,X,M,X,Y,Z 2000
600/1039 & 115/66.4 & 0.3 W,X,M,X,Y,Z & 2000 &
757563103 69000/69000Y 1.1 1.73 69 350 140 2.5
350/600:1 197/115 0.3 W,X,M,X,Y,Z 2000
600 & 0.3 W,X,M,X,Y,Z & 2000 &
757562600 69000/69000Y 115 & 115 1.1 1.73 69 350 140 2.5
600:1 0.3 W,X,M,X,Y,Z 2000
Notes:

CRE-7 5 kV CURRENT TRANSFORMER
CR Series are dry type outdoor service current transformers. The core is
encapsulated with Type B epoxy resin for excellence in internal dielectric
properties and mechanical strength. The external layer of Cycloaliphatic
resin provides resistance to ultraviolet rays and the effects of tracking and
erosion on the exterior of the module. The device is maintenance free,
ensuring a long mechanical and electrical life.
OUTDOOR
60 Hertz The core is built with silicon steel lamination. The blade is high permeability
grain oriented Type for low losses. The windings are copper wire with
copper plate double isolation. The concentric distribution of the coils
prevents magnetic ux leakage, achieving greater accuracy and higher
capacity to withstand mechanical stresses in adverse operating conditions.
Partial Discharge measurements exceed IEEE C57.13 2008 requirements.
Resin Gray 43 13.3 3
9.37 (238)
2 x 8.5 (2 x 216)
2 x 6.83 (2 x 173)
12.4 (315)
7.87 (2 x 200)
Terminal box
Two holes to
9.38 (238) conduit pipe
A1 - NPT
10.5 (267) Drawing number: 4287594
11 (279)
PRIMARY TERMINAL GROUND CONNECTOR SECONDARY TERMINAL ONE SECONDARY
H1 H2

/4
1
MARKING X1 X2
CONNEC- (Single
TIONS Primary
ONE SECONDARY with tap
Ratio)
H1 H2
Type: NEMA-2 Type: TE-12-250 Type: Quick Connector
Range: 4TRE-250MCM X1 X2 Xn


Power-Frequency
Current Short- Short- Highest
Thermal (1 min)
Ratio time time IEEE Nominal
Current Relay BIL
Code * (CEP) (Primary: Thermal Mechanical Metering Voltage
Rating Accuracy (kV) Primary & Secondary
Secondary) Current Current Accuracy System
Factor @ Secondary Winding
(A) (kA/1s) (kApeak) (kV)
30C (kVrms) (kVrms)
756311001 5:5 1.5 0.5 1.35 0.3 B1.8 T-100 5 60 19 2.5

756311002 10:5 1.5 1 2.7 0.3 B1.8 T-100 5 60 19 2.5
756311003 15:5 1.5 1.5 4.05 0.3 B1.8 T-100 5 60 19 2.5
756311004 20:5 1.5 2 5.4 0.3 B1.8 T-100 5 60 19 2.5
756311005 25:5 1.5 2.5 6.75 0.3 B1.8 T-100 5 60 19 2.5
756311006 30:5 1.5 3 8.1 0.3 B1.8 T-100 5 60 19 2.5
756311008 40:5 1.5 4 10.8 0.3 B1.8 T-100 5 60 19 2.5
756311010 50:5 1.5 5 13.5 0.3 B1.8 T-100 5 60 19 2.5
756311015 75:5 1.5 7.5 20.25 0.3 B1.8 T-100 5 60 19 2.5
756311020 100:5 1.5 10 27 0.3 B1.8 T-100 5 60 19 2.5
756311030 150:5 1.5 15 40.5 0.3 B1.8 T-100 5 60 19 2.5
756311040 200:5 1.5 20 54 0.3 B1.8 T-100 5 60 19 2.5
756311060 300:5 1.5 30 81 0.3 B1.8 T-100 5 60 19 2.5
756311080 400:5 1.5 40 108 0.3 B1.8 T-100 5 60 19 2.5
756311120 600:5 1.5 60 162 0.3 B1.8 T-100 5 60 19 2.5
756311160 800:5 1.5 80 216 0.3 B1.8 T-100 5 60 19 2.5
756311200 1000:5 1.5 100 270 0.3 B1.8 T-70 5 60 19 2.5
Notes:

CRB-17 15 kV CURRENT TRANSFORMER
ARTECHE CR series are dry type outdoor service current transformers.

Cycloaliphatic Epoxy Resin (CEP) provides resistance to ultraviolet rays and
the effects of tracking and erosion on the exterior of the transformer ensuring


requirements.
Resin Gray* 48.5 16.5 8
10.63 (270)
8.62 (219)
H1 H2
15.35 (390)
1 hole 9/16 Nameplate

2 holes to conduit to ground
pipe 1 NPT connection
10 (254)
H1 H2

/4
1
MARKING
CONNEC- (Single X1 X2
TIONS Primary
Ratio)

Range: 4TRE-250MCM


Power-Frequency
Ratio time time
Code * Current IEEE Metering Relay Voltage BIL
(Primary: Thermal Mechanical
(CEP) Rating Accuracy Accuracy System (kV) Primary & Secondary
30C (kVrms) (kVrms)
756203001 5:5 3.0 0.5 1.25 0.3 B-0.5 - 15 110 34 2.5

756203002 10:5 3.0 1 2.5 0.3 B-0.5 - 15 110 34 2.5
756203003 15:5 3.0 1.5 3.75 0.3 B-0.5 - 15 110 34 2.5
756203004 20:5 3.0 2 5 0.3 B-0.5 - 15 110 34 2.5
756203005 25:5 3.0 2.5 6.25 0.3 B-0.5 - 15 110 34 2.5
756203006 30:5 3.0 3 7.5 0.3 B-0.5 - 15 110 34 2.5
756203008 40:5 3.0 4 10 0.3 B-0.5 - 15 110 34 2.5
756203010 50:5 3.0 5 12.5 0.3 B-0.5 - 15 110 34 2.5
756203015 75:5 3.0 7.5 18.75 0.3 B-0.5 - 15 110 34 2.5
756203020 100:5 3.0 10 25 0.3 B-0.5 - 15 110 34 2.5
756203030 150:5 3.0 15 37.5 0.3 B-0.5 - 15 110 34 2.5
756203040 200:5 3.0 20 50 0.3 B-0.5 - 15 110 34 2.5
756203060 300:5 3.0 30 75 0.3 B-0.5 - 15 110 34 2.5
756203080 400:5 3.0 40 100 0.3 B-0.5 - 15 110 34 2.5
756203120 600:5 2.0 60 150 0.3 B-0.5 - 15 110 34 2.5
756203160 800:5 1.5 60 150 0.3 B-0.5 - 15 110 34 2.5
756203200 1000:5 1.0 75 127.5 0.3 B-0.5 - 15 110 34 2.5
756203240 1200:5 1.0 90 162 0.3 B-0.5 - 15 110 34 2.5
Shorting Link
756204001 5:5 3.0 0.5 1.25 0.3 B-0.5 - 15 110 34 2.5
756204002 10:5 3.0 1 2.5 0.3 B-0.5 - 15 110 34 2.5
756204003 15:5 3.0 1.5 3.75 0.3 B-0.5 - 15 110 34 2.5
756204004 20:5 3.0 2 5 0.3 B-0.5 - 15 110 34 2.5
756204005 25:5 3.0 2.5 6.25 0.3 B-0.5 - 15 110 34 2.5
756204006 30:5 3.0 3 7.5 0.3 B-0.5 - 15 110 34 2.5
756204008 40:5 3.0 4 10 0.3 B-0.5 - 15 110 34 2.5
756204010 50:5 3.0 5 12.5 0.3 B-0.5 - 15 110 34 2.5
756204015 75:5 3.0 7.5 18.75 0.3 B-0.5 - 15 110 34 2.5
756204020 100:5 3.0 10 25 0.3 B-0.5 - 15 110 34 2.5
756204030 150:5 3.0 15 37.5 0.3 B-0.5 - 15 110 34 2.5
756204040 200:5 3.0 20 50 0.3 B-0.5 - 15 110 34 2.5
756204060 300:5 3.0 30 75 0.3 B-0.5 - 15 110 34 2.5
756204080 400:5 3.0 40 100 0.3 B-0.5 - 15 110 34 2.5
756204120 600:5 2.0 60 150 0.3 B-0.5 - 15 110 34 2.5
756204160 800:5 1.5 60 150 0.3 B-0.5 - 15 110 34 2.5
756204200 1000:5 1.0 75 127.5 0.3 B-0.5 - 15 110 34 2.5
756204240 1200:5 1.0 90 162 0.3 B-0.5 - 15 110 34 2.5

Power-Frequency
Ratio time time
30C (kVrms) (kVrms)

756207001 5:5 1.5 0.5 1.25 0.15S B-0.5 - 15 110 34 2.5
756207002 10:5 1.5 1 2.5 0.15S B-0.5 - 15 110 34 2.5
756207003 15:5 1.5 1.5 3.75 0.15S B-0.5 - 15 110 34 2.5
756207004 20:5 1.5 2 5 0.15S B-0.5 - 15 110 34 2.5
756207005 25:5 1.5 2.5 6.25 0.15S B-0.5 - 15 110 34 2.5
756207006 30:5 1.5 3 7.5 0.15S B-0.5 - 15 110 34 2.5
756207008 40:5 1.5 4 10 0.15S B-0.5 - 15 110 34 2.5
756207010 50:5 1.5 5 12.5 0.15S B-0.5 - 15 110 34 2.5
756207015 75:5 1.5 7.5 18.75 0.15S B-0.5 - 15 110 34 2.5
756207020 100:5 1.5 10 25 0.15S B-0.5 - 15 110 34 2.5
756207030 150:5 1.5 15 37.5 0.15S B-0.5 - 15 110 34 2.5
756207040 200:5 1.5 20 50 0.15S B-0.5 - 15 110 34 2.5
756207060 300:5 1.5 30 75 0.15S B-0.5 - 15 110 34 2.5
756207080 400:5 1.5 40 100 0.15S B-0.5 - 15 110 34 2.5
756207120 600:5 1.5 60 150 0.15S B-0.5 - 15 110 34 2.5
756207160 800:5 1.2 60 150 0.15S B-0.5 - 15 110 34 2.5
756207200 1000:5 1.0 75 127.5 0.15S B-0.5 - 15 110 34 2.5
756207240 1200:5 1.0 90 162 0.15S B-0.5 - 15 110 34 2.5

756206040 200:5 2.0 20 50 0.15 B-0.5 - 15 110 34 2.5
756206120 600:5 1.5 60 150 0.15 B-0.5 - 15 110 34 2.5
756206200 1000:5 1.5 75 127.5 0.15 B-0.5 - 15 110 34 2.5
756206240 1200:5 1.2 90 162 0.15 B-0.5 - 15 110 34 2.5

Notes:




requirements.
Resin Gray* 68.3 16.5 8
12.05 (306)
8.62 (219)
H1 H2
15.35 (390)
2 holes to conduit 1 hole 9/16

pipe 1 NPT to ground
connection Nameplate
10 (254)
H1 H2

/4
1
MARKING X1 X2
CONNEC- (Single
TIONS Primary
Ratio)
H1 H2


Power-Frequency
Ratio time time
30C (kVrms) (kVrms)
756231001 5:5 1.5 0.5 0.95 0.3 B-1.8 T150 15 110 34 2.5
756231002 10:5 1.5 1 1.9 0.3 B-1.8 T150 15 110 34 2.5
756231003 15:5 1.5 1.5 2.85 0.3 B-1.8 T150 15 110 34 2.5
756231004 20:5 1.5 2 3.8 0.3 B-1.8 T150 15 110 34 2.5
756231005 25:5 1.5 2.5 4.75 0.3 B-1.8 T150 15 110 34 2.5
756231006 30:5 1.5 3 5.7 0.3 B-1.8 T150 15 110 34 2.5
756231008 40:5 1.5 4 7.6 0.3 B-1.8 T150 15 110 34 2.5
756231010 50:5 1.5 5 9.5 0.3 B-1.8 T150 15 110 34 2.5
756231012 60:5 1.5 6 11.4 0.3 B-1.8 T150 15 110 34 2.5
756231015 75:5 1.5 7.5 14.25 0.3 B-1.8 T150 15 110 34 2.5
756231020 100:5 1.5 10 19 0.3 B-1.8 T150 15 110 34 2.5
756231030 150:5 1.5 15 28.5 0.3 B-1.8 T150 15 110 34 2.5
756231040 200:5 1.5 20 38 0.3 B-1.8 T150 15 110 34 2.5
756231060 300:5 1.5 30 57 0.3 B-1.8 T150 15 110 34 2.5
756231080 400:5 1.5 40 76 0.3 B-1.8 T150 15 110 34 2.5
756231120 600:5 1.5 60 86.7 0.3 B-1.8 T150 15 110 34 2.5
756231160 800:5 1.5 60 114 0.3 B-1.8 T150 15 110 34 2.5
756231200 1000:5 1.2 75 142.5 0.3 B-1.8 T150 15 110 34 2.5
756231240 1200:5 1.0 90 171 0.3 B-1.8 T150 15 110 34 2.5
756232002 10/20:5 2.0/1.5 2 3.8 0.3B-0.5/0.3B-1.8 T75/T150 15 110 34 2.5
756232005 25/50:5 2.0/1.5 5 9.5 0.3B-0.5/0.3B-1.8 T75/T150 15 110 34 2.5
756232006 30/60:5 2.0/1.5 6 11.4 0.3B-0.5/0.3B-1.8 T75/T150 15 110 34 2.5
756232010 50/100:5 2.0/1.5 10 19 0.3B-0.5/0.3B-1.8 T75/T150 15 110 34 2.5
756232015 75/150:5 2.0/1.5 15 28.5 0.3B-0.5/0.3B-1.8 T75/T150 15 110 34 2.5
756232020 100/200:5 2.0/1.5 20 38 0.3B-0.5/0.3B-1.8 T75/T150 15 110 34 2.5
756232030 150:300:5 2.0/1.5 30 57 0.3B-0.5/0.3B-1.8 T75/T150 15 110 34 2.5
756232040 200/400:5 2.0/1.5 40 76 0.3B-0.5/0.3B-1.8 T75/T150 15 110 34 2.5
756232060 300/600:5 2.0/1.5 60 86.7 0.3B-0.5/0.3B-1.8 T75/T150 15 110 34 2.5
756232080 400/800:5 1.2/1.2 60 114 0.3B-0.5/0.3B-1.8 T75/T150 15 110 34 2.5
756232100 500/1000:5 1.0/1.0 75 142.5 0.3B-0.5/0.3B-1.8 T75/T150 15 110 34 2.5
756232120 600/1200:5 1.0/1.0 90 171 0.3B-0.5/0.3B-1.8 T75/T150 15 110 34 2.5
756239001 5:5 1.5 0.5 0.95 0.15B-0.9 - 15 110 34 2.5
756239002 10:5 1.5 1 1.9 0.15B-0.9 - 15 110 34 2.5
756239010 50:5 1.5 5 9.5 0.15B-0.9 - 15 110 34 2.5
756239015 75:5 1.5 7.5 14.25 0.15B-0.9 - 15 110 34 2.5
756239020 100:5 1.5 10 19 0.15B-0.9 - 15 110 34 2.5
756239120 600:5 1.5 60 86.7 0.15B-0.9 - 15 110 34 2.5
756239160 800:5 1.5 60 114 0.15B-0.9 - 15 110 34 2.5
756239200 1000:5 1.2 75 142.5 0.15B-0.9 - 15 110 34 2.5
756239240 1200:5 1.0 90 171 0.15B-0.9 - 15 110 34 2.5
756238001 5/10:5 2.0/1.5 1 1.9 0.15B-0.5/0.15B0.09 - 15 110 34 2.5
756238002 10/20:5 2.0/1.5 2 3.8 0.15B-0.5/0.15B0.09 - 15 110 34 2.5
756238060 300/600:5 2.0/1.5 60 86.7 0.15B-0.5/0.15B0.09 - 15 110 34 2.5
756238080 400/800:5 1.2/1.2 60 114 0.15B-0.5/0.15B0.09 - 15 110 34 2.5
756238100 500/1000:5 1.0/1.0 75 142.5 0.15B-0.5/0.15B0.09 - 15 110 34 2.5
756238120 600/1200:5 1.0/1.0 90 171 0.15B-0.5/0.15B0.09 - 15 110 34 2.5

Power-Frequency
Ratio time time
30C (kVrms) (kVrms)
Shorting Link
756234001 5:5 1.5 0.5 0.95 0.3 B-1.8 T150 15 110 34 2.5
756234002 10:5 1.5 1 1.9 0.3 B-1.8 T150 15 110 34 2.5
756234003 15:5 1.5 1.5 2.85 0.3 B-1.8 T150 15 110 34 2.5
756234004 20:5 1.5 2 3.8 0.3 B-1.8 T150 15 110 34 2.5
756234005 25:5 1.5 2.5 4.75 0.3 B-1.8 T150 15 110 34 2.5
756234006 30:5 1.5 3 5.7 0.3 B-1.8 T150 15 110 34 2.5
756234008 40:5 1.5 4 7.6 0.3 B-1.8 T150 15 110 34 2.5
756234010 50:5 1.5 5 9.5 0.3 B-1.8 T150 15 110 34 2.5
756234012 60:5 1.5 6 11.4 0.3 B-1.8 T150 15 110 34 2.5
756234015 75:5 1.5 7.5 14.25 0.3 B-1.8 T150 15 110 34 2.5
756234020 100:5 1.5 10 19 0.3 B-1.8 T150 15 110 34 2.5
756234030 150:5 1.5 15 28.5 0.3 B-1.8 T150 15 110 34 2.5
756234040 200:5 1.5 20 38 0.3 B-1.8 T150 15 110 34 2.5
756234060 300:5 1.5 30 57 0.3 B-1.8 T150 15 110 34 2.5
756234080 400:5 1.5 40 76 0.3 B-1.8 T150 15 110 34 2.5
756234120 600:5 1.5 60 86.7 0.3 B-1.8 T150 15 110 34 2.5
756234160 800:5 1.5 60 114 0.3 B-1.8 T150 15 110 34 2.5
756234200 1000:5 1.2 75 142.5 0.3 B-1.8 T150 15 110 34 2.5
756234240 1200:5 1.0 90 171 0.3 B-1.8 T150 15 110 34 2.5

756237001 5:5 1.5 0.5 0.95 0.15S B-0.9 - 15 110 34 2.5
756237002 10:5 1.5 1 1.9 0.15S B-0.9 - 15 110 34 2.5
756237010 50:5 1.5 5 9.5 0.15S B-0.9 - 15 110 34 2.5
756237015 75:5 1.5 7.5 14.25 0.15S B-0.9 - 15 110 34 2.5
756237020 100:5 1.5 10 19 0.15S B-0.9 - 15 110 34 2.5
756237040 200:5 1.5 20 38 0.15S B-0.9 - 15 110 34 2.5
756237060 300:5 1.5 30 57 0.15S B-0.9 - 15 110 34 2.5
756237120 600:5 1.5 60 86.7 0.15S B-0.9 - 15 110 34 2.5
756237160 800:5 1.5 60 114 0.15S B-0.9 - 15 110 34 2.5
756237200 1000:5 1.2 75 142.5 0.15S B-0.9 - 15 110 34 2.5
756237240 1200:5 1.0 90 171 0.15S B-0.9 - 15 110 34 2.5

756236040 200:5 2.0 20 38 0.15 B-1.8 - 15 110 34 2.5
756236120 600:5 1.5 60 86.7 0.15 B-1.8 - 15 110 34 2.5
756236200 1000:5 1.5 75 142.5 0.15 B-1.8 - 15 110 34 2.5
756236240 1200:5 1.2 90 171 0.15 B-1.8 - 15 110 34 2.5

Notes:

CRF-17 15 kV CURRENT TRANSFORMER



requirements.
Resin Gray* 112.4 27.55 12
13,70 (348)
8.62 (219)
H1 H2
17.2 (437)
Lifting holes
3/4 (19)

2 Holes to conduit to ground
10 (254)
Drawing number: 4286582/4287310**
H1 H2
4
/
1
MARKING X1 X2
CONNEC- (Single
TIONS Primary
Ratio)
H1 H2
Type: NEMA-2 Type: NEMA-4 Type: TE-12-250 Type: Quick Connector
Material: Copper Material: Copper Material: Copper Material: Brass
** Range: 4TRE-250MCM X1 X2 Xn


Power-Frequency
Ratio time time
30C (kVrms) (kVrms)
756191001 5:5 1.5 0.5 0.95 0.3B-1.8 T200 15 110 34 2.5

756191002 10:5 1.5 1 1.9 0.3B-1.8 T200 15 110 34 2.5
756191003 15:5 1.5 1.5 2.85 0.3B-1.8 T200 15 110 34 2.5
756191004 20:5 1.5 2 3.8 0.3B-1.8 T200 15 110 34 2.5
756191005 25:5 1.5 2.5 4.75 0.3B-1.8 T200 15 110 34 2.5
756191006 30:5 1.5 3 5.7 0.3B-1.8 T200 15 110 34 2.5
756191008 40:5 1.5 4 7.6 0.3B-1.8 T200 15 110 34 2.5
756191010 50:5 1.5 5 9.5 0.3B-1.8 T200 15 110 34 2.5
756191012 60:5 1.5 6 11.4 0.3B-1.8 T200 15 110 34 2.5
756191015 75:5 1.5 7.5 14.25 0.3B-1.8 T200 15 110 34 2.5
756191020 100:5 1.5 10 19 0.3B-1.8 T200 15 110 34 2.5
756191030 150:5 1.5 15 37.5 0.3B-1.8 T200 15 110 34 2.5
756191040 200:5 1.5 20 50 0.3B-1.8 T200 15 110 34 2.5
756191060 300:5 1.5 30 75 0.3B-1.8 T200 15 110 34 2.5
756191080 400:5 1.5 40 100 0.3B-1.8 T200 15 110 34 2.5
756191120 600:5 1.5 60 86.7 0.3B-1.8 T200 15 110 34 2.5
756191160 800:5 1.2 60 114 0.3B-1.8 T200 15 110 34 2.5
756191200 1000:5 1.0 75 142.5 0.3B-1.8 T200 15 110 34 2.5
756191240 1200:5 1.0 90 171 0.3B-1.8 T200 15 110 34 2.5
756192001 5/10:5 2.0/1.5 1 1.9 0.3B-0.9/0.3B-1.8 T100/200 15 110 34 2.5
756192002 10/20:5 2.0/1.5 2 3.8 0.3B-0.9/0.3B-1.8 T100/200 15 110 34 2.5
756192005 25/50:5 2.0/1.5 5 9.5 0.3B-0.9/0.3B-1.8 T100/200 15 110 34 2.5
756192006 30/60:5 2.0/1.5 6 11.4 0.3B-0.9/0.3B-1.8 T100/200 15 110 34 2.5
756192010 50/100:5 2.0/1.5 10 19 0.3B-0.9/0.3B-1.8 T100/200 15 110 34 2.5
756192015 75/150:5 2.0/1.5 15 28.5 0.3B-0.9/0.3B-1.8 T100/200 15 110 34 2.5
756192020 100/200:5 2.0/1.5 20 38 0.3B-0.9/0.3B-1.8 T100/200 15 110 34 2.5
756192030 150/300:5 2.0/1.5 30 57 0.3B-0.9/0.3B-1.8 T100/200 15 110 34 2.5
756192040 200/400:5 2.0/1.5 40 76 0.3B-0.9/0.3B-1.8 T100/200 15 110 34 2.5
756192060 300/600:5 2.0/1.5 60 86.7 0.3B-0.9/0.3B-1.8 T100/200 15 110 34 2.5
756192080 400/800:5 1.2/1.2 60 114 0.3B-0.9/0.3B-1.8 T100/200 15 110 34 2.5
756192100 500/1000:5 1.0/1.0 75 142.5 0.3B-0.9/0.3B-1.8 T100/200 15 110 34 2.5
756192120 600/1200:5 1.0/1.0 90 171 0.3B-0.9/0.3B-1.8 T100/200 15 110 34 2.5
756199001 5:5 1.5 0.5 0.95 0.15B-0.9 - 15 110 34 2.5
756199002 10:5 1.5 1 1.9 0.15B-0.9 - 15 110 34 2.5
756199010 50:5 1.5 5 9.5 0.15B-0.9 - 15 110 34 2.5
756199015 75:5 1.5 7.5 14.25 0.15B-0.9 - 15 110 34 2.5
756199040 100:5 1.5 10 19 0.15B-0.9 - 15 110 34 2.5
756199120 600:5 1.5 10 19 0.15B-0.9 - 15 110 34 2.5
756199160 800:5 1.2 60 86.7 0.15B-0.9 - 15 110 34 2.5
756199200 1000:5 1.0 60 114 0.15B-0.9 - 15 110 34 2.5
756199240 1200:5 1.0 90 171 0.15B-0.9 - 15 110 34 2.5
756198001 5/10:5 2.0/1.5 1 1.9 0.15B-0.5/0.15B-0.9 - 15 110 34 2.5
756198002 10/20:5 2.0/1.5 2 3.8 0.15B-0.5/0.15B-0.9 - 15 110 34 2.5
756198060 300/600:5 2.0/1.5 60 86.7 0.15B-0.5/0.15B-0.9 - 15 110 34 2.5
756198080 400/800:5 1.2/1.2 60 114 0.15B-0.5/0.15B-0.9 - 15 110 34 2.5
756198100 500/1000:5 1.0/1.0 75 142.5 0.15B-0.5/0.15B-0.9 - 15 110 34 2.5
756198120 600/1200:5 1.0/1.0 90 171 0.15B-0.5/0.15B-0.9 - 15 110 34 2.5

Power-Frequency
Ratio time time
30C (kVrms) (kVrms)

756197001 5:5 2.0 0.5 0.95 0.15S B-0.5 - 15 110 34 2.5
756197002 10:5 2.0 1 1.9 0.15S B-0.5 - 15 110 34 2.5
756197010 50:5 2.0 5 9.5 0.15S B-0.5 - 15 110 34 2.5
756197015 75:5 2.0 7.5 14.25 0.15S B-0.5 - 15 110 34 2.5
756197100 100:5 2.0 10 19 0.15S B-0.5 - 15 110 34 2.5
756197120 600:5 2.0 10 19 0.15S B-0.5 - 15 110 34 2.5
756197160 800:5 1.5 60 86.7 0.15S B-0.9 - 15 110 34 2.5
756197200 1000:5 1.2 60 114 0.15S B-0.9 - 15 110 34 2.5
756197240 1200:5 1.2 90 171 0.15S B-0.9 - 15 110 34 2.5

756196040 200:5 4.0 10 19 0.15 B-1.8 - 15 110 34 2.5
756196120 600:5 3.0 10 19 0.15 B-1.8 - 15 110 34 2.5
756196200 1000:5 2.0 60 114 0.15 B-1.8 - 15 110 34 2.5
756196240 1200:5 1.5 90 171 0.15 B-1.8 - 15 110 34 2.5

Notes:


O
60 Hertz
6 Epoxy Resin (HCEP) which improves service life expectancy due to its

requirements.
Mechanical
Mec
chan
hanical characteristics
C Weight (lbs.) Creepage distance (in) Strike distance (in)
Resin Gray*
G 78.2 24.4 10
12.05 (306)
H1 H2
8.62 (219)
18.11 (460)
2 holes to 1 hole 9/16

conduit to ground Nameplate
pipe 1 NPT connection 10 (254)
H1 H2

/4
1
MARKING
CONNEC- (Single X1 X2
TIONS Primary
Ratio)

Range: 4TRE-250MCM


Power-Frequency
Ratio time time
30C (kVrms) (kVrms)
756243001 5:5 3.0 0.5 1.25 0.3B-0.9 T60 25 150 50 2.5

756243002 10:5 3.0 1 2.5 0.3B-0.9 T60 25 150 50 2.5
756243003 15:5 3.0 1.5 3.75 0.3B-0.9 T60 25 150 50 2.5
756243004 20:5 3.0 2 5 0.3B-0.9 T60 25 150 50 2.5
756243005 25:5 3.0 2.5 6.25 0.3B-0.9 T60 25 150 50 2.5
756243006 30:5 3.0 3 7.5 0.3B-0.9 T60 25 150 50 2.5
756243008 40:5 3.0 4 10 0.3B-0.9 T60 25 150 50 2.5
756243010 50:5 3.0 5 12.5 0.3B-0.9 T60 25 150 50 2.5
756243015 75:5 3.0 7.5 18.75 0.3B-0.9 T60 25 150 50 2.5
756243020 100:5 3.0 10 25 0.3B-0.9 T60 25 150 50 2.5
756243030 150:5 3.0 15 37.5 0.3B-0.9 T60 25 150 50 2.5
756243040 200:5 3.0 20 50 0.3B-0.9 T60 25 150 50 2.5
756243060 300:5 3.0 30 75 0.3B-0.9 T60 25 150 50 2.5
756243080 400:5 3.0 40 100 0.3B-0.9 T60 25 150 50 2.5
756243120 600:5 2.0 60 150 0.3B-0.9 T60 25 150 50 2.5
756243160 800:5 1.5 60 150 0.3B-0.9 T60 25 150 50 2.5
756243200 1000:5 1.0 75 127.5 0.3B-0.9 T60 25 150 50 2.5
756243240 1200:5 1.0 90 162 0.3B-0.9 T60 25 150 50 2.5

756246040 200:5 2.0 20 50 0.15 B-1.8 - 25 150 50 2.5
756246120 600:5 1.5 60 150 0.15 B-1.8 - 25 150 50 2.5
756246200 1000:5 1.5 75 127.5 0.15 B-1.8 - 25 150 50 2.5
756246240 1200:5 1.2 90 162 0.15 B-1.8 - 25 150 50 2.5
Notes:




requirements.
Resin Gray* 112.4 27.55 12
13,70 (348)
8.62 (219)
H1 H2
17.2 (437)
Lifting holes
3/4 (19)

2 Holes to conduit to ground
10 (254)
Drawing number: 9448131/4287311**
H1 H2
4
/
1
MARKING X1 X2
CONNEC- (Single
TIONS Primary
Ratio)
H1 H2
Type: NEMA-2 Type: NEMA-4 Type: TE-12-250 Type: Quick Connector
** Range: 4TRE-250MCM X1 X2 Xn


Power-Frequency
Ratio time time
30C (kVrms) (kVrms)
756261001 5:5 1.5 0.5 0.95 0.3B-1.8 T200 25 150 50 2.5

756261002 10:5 1.5 1 1.9 0.3B-1.8 T200 25 150 50 2.5
756261003 15:5 1.5 1.5 2.85 0.3B-1.8 T200 25 150 50 2.5
756261004 20:5 1.5 2 3.8 0.3B-1.8 T200 25 150 50 2.5
756261005 25:5 1.5 2.5 4.75 0.3B-1.8 T200 25 150 50 2.5
756261006 30:5 1.5 3 5.7 0.3B-1.8 T200 25 150 50 2.5
756261008 40:5 1.5 4 7.6 0.3B-1.8 T200 25 150 50 2.5
756261010 50:5 1.5 5 9.5 0.3B-1.8 T200 25 150 50 2.5
756261012 60:5 1.5 6 11.4 0.3B-1.8 T200 25 150 50 2.5
756261015 75:5 1.5 7.5 14.25 0.3B-1.8 T200 25 150 50 2.5
756261020 100:5 1.5 10 19 0.3B-1.8 T200 25 150 50 2.5
756261030 150:5 1.5 15 37.5 0.3B-1.8 T200 25 150 50 2.5
756261040 200:5 1.5 20 50 0.3B-1.8 T200 25 150 50 2.5
756261060 300:5 1.5 30 75 0.3B-1.8 T200 25 150 50 2.5
756261080 400:5 1.5 40 100 0.3B-1.8 T200 25 150 50 2.5
756261120 600:5 1.5 60 86.7 0.3B-1.8 T200 25 150 50 2.5
756261160 800:5 1.2 60 114 0.3B-1.8 T200 25 150 50 2.5
756261200 1000:5 1.0 75 142.5 0.3B-1.8 T200 25 150 50 2.5
756261240 1200:5 1.0 90 171 0.3B-1.8 T200 25 150 50 2.5
756262001 5/10:5 2.0/1.5 1 1.9 0.3B-0.9/0.3B-1.8 T100/200 25 150 50 2.5
756262002 10/20:5 2.0/1.5 2 3.8 0.3B-0.9/0.3B-1.8 T100/200 25 150 50 2.5
756262005 25/50:5 2.0/1.5 5 9.5 0.3B-0.9/0.3B-1.8 T100/200 25 150 50 2.5
756262006 30/60:5 2.0/1.5 6 11.4 0.3B-0.9/0.3B-1.8 T100/200 25 150 50 2.5
756262010 50/100:5 2.0/1.5 10 19 0.3B-0.9/0.3B-1.8 T100/200 25 150 50 2.5
756262015 75/150:5 2.0/1.5 15 28.5 0.3B-0.9/0.3B-1.8 T100/200 25 150 50 2.5
756262020 100/200:5 2.0/1.5 20 38 0.3B-0.9/0.3B-1.8 T100/200 25 150 50 2.5
756262030 150/300:5 2.0/1.5 30 57 0.3B-0.9/0.3B-1.8 T100/200 25 150 50 2.5
756262040 200/400:5 2.0/1.5 40 76 0.3B-0.9/0.3B-1.8 T100/200 25 150 50 2.5
756262060 300/600:5 2.0/1.5 60 86.7 0.3B-0.9/0.3B-1.8 T100/200 25 150 50 2.5
756262080 400/800:5 1.2/1.2 60 114 0.3B-0.9/0.3B-1.8 T100/200 25 150 50 2.5
756262100 500/1000:5 1.0/1.0 75 142.5 0.3B-0.9/0.3B-1.8 T100/200 25 150 50 2.5
756262120 600/1200:5 1.0/1.0 90 171 0.3B-0.9/0.3B-1.8 T100/200 25 150 50 2.5
756269001 5:5 1.5 0.5 0.95 0.15B-0.9 - 25 150 50 2.5
756269002 10:5 1.5 1 1.9 0.15B-0.9 - 25 150 50 2.5
756269010 50:5 1.5 5 9.5 0.15B-0.9 - 25 150 50 2.5
756269015 75:5 1.5 7.5 14.25 0.15B-0.9 - 25 150 50 2.5
756269020 100:5 1.5 10 19 0.15B-0.9 - 25 150 50 2.5
756269120 600:5 1.5 10 19 0.15B-0.9 - 25 150 50 2.5
756269160 800:5 1.2 60 86.7 0.15B-0.9 - 25 150 50 2.5
756269200 1000:5 1.0 60 114 0.15B-0.9 - 25 150 50 2.5
756269240 1200:5 1.0 90 171 0.15B-0.9 - 25 150 50 2.5
756268001 5/10:5 2.0/1.5 1 1.9 0.15B-0.5/B-0.9 - 25 150 50 2.5
756268002 10/20:5 2.0/1.5 2 3.8 0.15B-0.5/B-0.9 - 25 150 50 2.5
756268060 300/600:5 2.0/1.5 60 86.7 0.15B-0.5/B-0.9 - 25 150 50 2.5
756268080 400/800:5 1.2/1.2 60 114 0.15B-0.5/B-0.9 - 25 150 50 2.5
756268100 500/1000:5 1.0/1.0 75 142.5 0.15B-0.5/B-0.9 - 25 150 50 2.5
756268120 600/1200:5 1.0/1.0 90 171 0.15B-0.5/B-0.9 - 25 150 50 2.5

Power-Frequency
Ratio time time
30C (kVrms) (kVrms)

756267001 5:5 2.0 0.5 0.95 0.15S B-0.5 - 25 150 50 2.5
756267002 10:5 2.0 1 1.9 0.15S B-0.5 - 25 150 50 2.5
756267010 50:5 2.0 5 9.5 0.15S B-0.5 - 25 150 50 2.5
756267015 75:5 2.0 7.5 14.25 0.15S B-0.5 - 25 150 50 2.5
756267020 100:5 2.0 10 19 0.15S B-0.5 - 25 150 50 2.5
756267120 600:5 2.0 10 19 0.15S B-0.5 - 25 150 50 2.5
756267160 800:5 1.5 60 86.7 0.15S B-0.9 - 25 150 50 2.5
756267200 1000:5 1.2 60 114 0.15S B-0.9 - 25 150 50 2.5
756267240 1200:5 1.2 90 171 0.15S B-0.9 - 25 150 50 2.5

756266040 200:5 4.0 10 19 0.15 B-1.8 - 25 150 50 2.5
756266120 600:5 3.0 10 19 0.15 B-1.8 - 25 150 50 2.5
756266200 1000:5 2.0 60 114 0.15 B-1.8 - 25 150 50 2.5
756266240 1200:5 1.5 90 171 0.15 B-1.8 - 25 150 50 2.5

Notes:

CE-034 34.5 kV CURRENT TRANSFORMER
ARTECHE CE series are dry type outdoor service top-core current

provides excellent internal dielectric properties and mechanical strength.
The external layer of Cycloaliphatic Epoxy Resin (CEP) provides resistance
to ultraviolet rays and the effects of tracking and erosion on the exterior
of the transformer ensuring a long mechanical and electrical life. The
transformer is maintenance free.
OUTDOOR
withstand mechanical stresses in adverse operating conditions. The cores
and windings are located in the upper part of the transformer. This head is
coated with a conductive layer, which provides an adequate electric eld
control.

requirements.
Resin Gray* 550 37.6 11
16.14 (410) 35.512 (902)
H2 H1
13.77 (350)
40 (1016)
Terminal 13.77 (350)

box Ground
connector
H1 H2
MARKING X1 X2
CONNEC- (Single
TIONS Primary
Ratio)
H1 H2
Type: PM30MC0-1-4N-E Type: LZ-500 Type: Hex screw
Material: Aluminum Material: Copper Material: Steel
Range: 4/OTRE-500MCM X1 X2 Xn


CE-034 34.5 kV CURRENT TRANSFORMER
Power-Frequency
Ratio time time
30C (kVrms) (kVrms)
756151001 5:5 2,0 0.5 0.95 0.3B-1.8 T-400 34.5 200 70 2.5
756151002 10:5 2,0 1 1.9 0.3B-1.8 T-400 34.5 200 70 2.5
756151003 15:5 2,0 1.5 2.85 0.3B-1.8 T-400 34.5 200 70 2.5
756151004 20:5 2,0 2 3.8 0.3B-1.8 T-400 34.5 200 70 2.5
756151005 25:5 2,0 2.5 4.75 0.3B-1.8 T-400 34.5 200 70 2.5
756151006 30:5 2,0 3 5.7 0.3B-1.8 T-400 34.5 200 70 2.5
756151008 40:5 2,0 4 7.6 0.3B-1.8 T-400 34.5 200 70 2.5
756151010 50:5 2,0 5 9.5 0.3B-1.8 T-400 34.5 200 70 2.5
756151015 75:5 2,0 6 11.4 0.3B-1.8 T-400 34.5 200 70 2.5
756151020 100:5 2,0 7.5 14.25 0.3B-1.8 T-400 34.5 200 70 2.5
756151030 150:5 2,0 10 19 0.3B-1.8 T-400 34.5 200 70 2.5
756151040 200:5 2,0 20 38 0.3B-1.8 T-400 34.5 200 70 2.5
756151060 300:5 2,0 30 57 0.3B-1.8 T-400 34.5 200 70 2.5
756151080 400:5 2,0 40 76 0.3B-1.8 T-400 34.5 200 70 2.5
756151120 600:5 2,0 50 9.5 0.3B-1.8 T-400 34.5 200 70 2.5
756151160 800:5 2,0 60 86.7 0.3B-1.8 T-400 34.5 200 70 2.5
756151200 1000:5 1.5 60 114 0.3B-1.8 T-400 34.5 200 70 2.5
756151240 1200:5 1.5 75 142.5 0.3B-1.8 T-400 34.5 200 70 2.5
756151400 2000:5 1.2 90 171 0.3B-1.8 T-800 34.5 200 70 2.5
756152001 10/20:5 3.0/2.0 2 3.8 0.3B-1.8/0.3B1.8 T200/T400 34.5 200 70 2.5
756152005 25/50:5 3.0/2.0 5 9.5 0.3B-1.8/0.3B1.8 T200/T400 34.5 200 70 2.5
756152006 30/60:5 3.0/2.0 6 11.4 0.3B-1.8/0.3B1.8 T200/T400 34.5 200 70 2.5
756152010 50/100:5 3.0/2.0 10 19 0.3B-1.8/0.3B1.8 T200/T400 34.5 200 70 2.5
756152015 75/150:5 3.0/2.0 15 28.5 0.3B-1.8/0.3B1.8 T200/T400 34.5 200 70 2.5
756152020 100/200:5 3.0/2.0 20 38 0.3B-1.8/0.3B1.8 T200/T400 34.5 200 70 2.5
756152030 150/300:5 3.0/2.0 30 57 0.3B-1.8/0.3B1.8 T200/T400 34.5 200 70 2.5
756152040 200/400:5 3.0/2.0 40 76 0.3B-1.8/0.3B1.8 T200/T400 34.5 200 70 2.5
756152060 300/600:5 3.0/2.0 60 86.7 0.3B-1.8/0.3B1.8 T200/T400 34.5 200 70 2.5
756152080 400/800:5 3.0/2.0 60 114 0.3B-1.8/0.3B1.8 T200/T400 34.5 200 70 2.5
756152100 500/1000:5 3.0/1.5 75 142.5 0.3B-1.8/0.3B1.8 T200/T400 34.5 200 70 2.5
756152120 600/1200:5 3.0/1.5 90 171 0.3B-1.8/0.3B1.8 T200/T400 34.5 200 70 2.5
756152150 750/1500:5 3.0/1.5 90 171 0.3B-1.8/0.3B1.8 T200/T400 34.5 200 70 2.5
756152200 1000/2000:5 2.4/1.2 90 171 0.3B-1.8/0.3B1.8 T400/T800 34.5 200 70 2.5
756152300 1500/3000:5 2.4/1.2 90 171 0.3B-1.8/0.3B1.8 T400/T800 34.5 200 70 2.5

CRF-36 34.5 kV CURRENT TRANSFORMER



requirements.
Resin Gray* 134.4 36.2 15
13.7 (348)
8.62 (219)
19.5 (495)

2 hole to conduit to ground
10 (254)
H1 H2

/4
1
MARKING X1 X2
CONNEC- (Single
TIONS Primary
Ratio)
H1 H2


Power-Frequency
Ratio time time
30C (kVrms) (kVrms)
756273001 5:5 3.0 0.5 1.25 0.3B-1.8 T100 34.5 200 70 2.5
756273002 10:5 3.0 1 2.5 0.3B-1.8 T100 34.5 200 70 2.5
756273003 15:5 3.0 1.5 3.75 0.3B-1.8 T100 34.5 200 70 2.5
756273004 20:5 3.0 2 5 0.3B-1.8 T100 34.5 200 70 2.5
756273005 25:5 3.0 2.5 6.25 0.3B-1.8 T100 34.5 200 70 2.5
756273006 30:5 3.0 3 7.5 0.3B-1.8 T100 34.5 200 70 2.5
756273008 40:5 3.0 4 10 0.3B-1.8 T100 34.5 200 70 2.5
756273010 50:5 3.0 5 12.5 0.3B-1.8 T100 34.5 200 70 2.5
756273015 75:5 3.0 7.5 18.75 0.3B-1.8 T100 34.5 200 70 2.5
756273020 100:5 3.0 10 25 0.3B-1.8 T100 34.5 200 70 2.5
756273030 150:5 3.0 15 37.5 0.3B-1.8 T100 34.5 200 70 2.5
756273040 200:5 3.0 20 50 0.3B-1.8 T100 34.5 200 70 2.5
756273060 300:5 3.0 30 75 0.3B-1.8 T100 34.5 200 70 2.5
756273080 400:5 3.0 40 100 0.3B-1.8 T100 34.5 200 70 2.5
756273120 600:5 2.0 60 150 0.3B-1.8 T100 34.5 200 70 2.5
756273160 800:5 1.5 60 150 0.3B-1.8 T100 34.5 200 70 2.5
756273200 1000:5 1.0 75 127.5 0.3B-1.8 T100 34.5 200 70 2.5
756273240 1200:5 1.0 90 162 0.3B-1.8 T100 34.5 200 70 2.5
756271001 5:5 1.5 0.5 0.95 0.3B-1.8 T200 34.5 200 70 2.5
756271002 10:5 1.5 1 1.9 0.3B-1.8 T200 34.5 200 70 2.5
756271003 15:5 1.5 1.5 2.85 0.3B-1.8 T200 34.5 200 70 2.5
756271004 20:5 1.5 2 3.8 0.3B-1.8 T200 34.5 200 70 2.5
756271005 25:5 1.5 2.5 4.75 0.3B-1.8 T200 34.5 200 70 2.5
756271006 30:5 1.5 3 5.7 0.3B-1.8 T200 34.5 200 70 2.5
756271008 40:5 1.5 4 7.6 0.3B-1.8 T200 34.5 200 70 2.5
756271010 50:5 1.5 5 9.5 0.3B-1.8 T200 34.5 200 70 2.5
756271012 60:5 1.5 6 11.4 0.3B-1.8 T200 34.5 200 70 2.5
756271015 75:5 1.5 7.5 14.25 0.3B-1.8 T200 34.5 200 70 2.5
756271020 100:5 1.5 10 19 0.3B-1.8 T200 34.5 200 70 2.5
756271040 200:5 1.5 20 38 0.3B-1.8 T200 34.5 200 70 2.5
756271060 300:5 1.5 30 57 0.3B-1.8 T200 34.5 200 70 2.5
756271080 400:5 1.5 40 76 0.3B-1.8 T200 34.5 200 70 2.5
756271100 500:5 1.5 50 9.5 0.3B-1.8 T200 34.5 200 70 2.5
756271120 600:5 1.2 60 86.7 0.3B-1.8 T200 34.5 200 70 2.5
756271160 800:5 1.0 60 114 0.3B-1.8 T200 34.5 200 70 2.5
756271200 1000:5 1.0 75 142.5 0.3B-1.8 T200 34.5 200 70 2.5
756271240 1200:5 1.0 90 171 0.3B-1.8 T200 34.5 200 70 2.5
756272002 10/20:5 2.0/1.5 2 3.8 0.3B-0.9/0.3B-1.8 T100/T200 34.5 200 70 2.5
756272005 25/50:5 2.0/1.5 5 9.5 0.3B-0.9/0.3B-1.8 T100/T200 34.5 200 70 2.5
756272006 30/60:5 2.0/1.5 6 11.4 0.3B-0.9/0.3B-1.8 T100/T200 34.5 200 70 2.5
756272010 50/100:5 2.0/1.5 10 19 0.3B-0.9/0.3B-1.8 T100/T200 34.5 200 70 2.5
756272015 75/150:5 2.0/1.5 15 28.5 0.3B-0.9/0.3B-1.8 T100/T200 34.5 200 70 2.5
756272020 100/200:5 2.0/1.5 20 38 0.3B-0.9/0.3B-1.8 T100/T200 34.5 200 70 2.5

Power-Frequency
Ratio time time
30C (kVrms) (kVrms)
756272030 150/300:5 2.0/1.5 30 57 0.3B-0.9/0.3B-1.8 T100/T200 34.5 200 70 2.5

756272040 200/400:5 2.0/1.5 40 76 0.3B-0.9/0.3B-1.8 T100/T200 34.5 200 70 2.5
756272060 300/600:5 2.0/1.5 60 86.7 0.3B-0.9/0.3B-1.8 T100/T200 34.5 200 70 2.5
756272080 400/800:5 1.2/1.2 60 114 0.3B-0.9/0.3B-1.8 T100/T200 34.5 200 70 2.5
756272100 500/1000:5 1.0/1.0 75 142.5 0.3B-0.9/0.3B-1.8 T100/T200 34.5 200 70 2.5
756272120 600/1200:5 1.0/1.0 90 171 0.3B-0.9/0.3B-1.8 T100/T200 34.5 200 70 2.5
756279001 5:5 1.5 0.5 0.95 0.15B-0.9 - 34.5 200 70 2.5
756279002 10:5 1.5 1 1.9 0.15B-0.9 - 34.5 200 70 2.5
756279010 50:5 1.5 5 9.5 0.15B-0.9 - 34.5 200 70 2.5
756279015 75:5 1.5 7.5 14.25 0.15B-0.9 - 34.5 200 70 2.5
756279020 100:5 1.5 10 19 0.15B-0.9 - 34.5 200 70 2.5
756279120 600:5 1.2 60 86.7 0.15B-0.9 - 34.5 200 70 2.5
756279160 800:5 1.0 60 114 0.15B-0.9 - 34.5 200 70 2.5
756279240 1200:5 1.0 90 171 0.15B-0.9 - 34.5 200 70 2.5
756278001 5/10:5 2.0/1.5 1 1.9 0.15B-0.5/B-0.9 - 34.5 200 70 2.5
756278002 10/20:5 2.0/1.5 2 3.8 0.15B-0.5/B-0.9 - 34.5 200 70 2.5
756278060 300/600:5 2.0/1.5 60 86.7 0.15B-0.5/B-0.9 - 34.5 200 70 2.5
756278080 400/800:5 1.2/1.2 60 114 0.15B-0.5/B-0.9 - 34.5 200 70 2.5
756278100 500/1000:5 1.0/1.0 75 142.5 0.15B-0.5/B-0.9 - 34.5 200 70 2.5
756278120 600/1200:5 1.0/1.0 90 171 0.15B-0.5/B-0.9 - 34.5 200 70 2.5

756276040 200:5 2.0 20 50 0.15 B-1.8 - 34.5 200 70 2.5
756276120 600:5 1.5 60 150 0.15 B-1.8 - 34.5 200 70 2.5
756276200 1000:5 1.5 75 127.5 0.15 B-1.8 - 34.5 200 70 2.5
756276240 1200:5 1.2 90 162 0.15 B-1.8 - 34.5 200 70 2.5

Notes:

CRH-36 34.5 kV CURRENT TRANSFORMER



requirements.
Resin Gray* 253.5 47.83 19.3
15.31 (388.87)
Nameplate
24.68 (626.8)
9.84 (250)
Lifting holes
Secondary
1 hole 9/16 to 2 holes 1
terminals
ground connector to conduit
pipe NPT
9.84 (250)
H1 H2
4
/
1
MARKING X1 X2
CONNEC- (Single
TIONS Primary
Ratio)
1500 A 2000 A
H1 H2
Type: NEMA-4 Type: LZ-250 Type: Quick Connector


CRH-36 34.5 kV CURRENT TRANSFORMER
Power-Frequency
Ratio time time
30C (kVrms) (kVrms)
756861001 5:5 2.0 0.5 0.95 0.3B-1.8 T200 34.5 200 70 2.5
756861002 10:5 2.0 1 1.9 0.3B-1.8 T200 34.5 200 70 2.5
756861003 15:5 2.0 1.5 2.85 0.3B-1.8 T200 34.5 200 70 2.5
756861004 20:5 2.0 2 3.8 0.3B-1.8 T200 34.5 200 70 2.5
756861005 25:5 2.0 2.5 4.75 0.3B-1.8 T200 34.5 200 70 2.5
756861006 30:5 2.0 3 5.7 0.3B-1.8 T200 34.5 200 70 2.5
756861008 40:5 2.0 4 7.6 0.3B-1.8 T200 34.5 200 70 2.5
756861010 50:5 2.0 5 9.5 0.3B-1.8 T200 34.5 200 70 2.5
756861015 75:5 2.0 6 11.4 0.3B-1.8 T200 34.5 200 70 2.5
756861020 100:5 2.0 7.5 14.25 0.3B-1.8 T200 34.5 200 70 2.5
756861030 150:5 2.0 10 19 0.3B-1.8 T200 34.5 200 70 2.5
756861040 200:5 2.0 20 38 0.3B-1.8 T200 34.5 200 70 2.5
756861060 300:5 2.0 30 57 0.3B-1.8 T200 34.5 200 70 2.5
756861080 400:5 2.0 40 76 0.3B-1.8 T200 34.5 200 70 2.5
756861100 500:5 2.0 50 9.5 0.3B-1.8 T200 34.5 200 70 2.5
756861120 600:5 2.0 60 86.7 0.3B-1.8 T200 34.5 200 70 2.5
756861160 800:5 2.0 60 114 0.3B-1.8 T200 34.5 200 70 2.5
756861200 1000:5 1.5 75 142.5 0.3B-1.8 T200 34.5 200 70 2.5
756861240 1200:5 1.5 90 171 0.3B-1.8 T200 34.5 200 70 2.5
756862002 10/20:5 3.0/2.0 2 3.8 0.3B-1.8/0.3B1.8 T100/T200 34.5 200 70 2.5
756862005 25/50:5 3.0/2.0 5 9.5 0.3B-1.8/0.3B1.8 T100/T200 34.5 200 70 2.5
756862006 30/60:5 3.0/2.0 6 11.4 0.3B-1.8/0.3B1.8 T100/T200 34.5 200 70 2.5
756862010 50/100:5 3.0/2.0 10 19 0.3B-1.8/0.3B1.8 T100/T200 34.5 200 70 2.5
756862015 75/150:5 3.0/2.0 15 28.5 0.3B-1.8/0.3B1.8 T100/T200 34.5 200 70 2.5
756862020 100/200:5 3.0/2.0 20 38 0.3B-1.8/0.3B1.8 T100/T200 34.5 200 70 2.5
756862030 150/300:5 3.0/2.0 30 57 0.3B-1.8/0.3B1.8 T100/T200 34.5 200 70 2.5
756862040 200/400:5 3.0/2.0 40 76 0.3B-1.8/0.3B1.8 T100/T200 34.5 200 70 2.5
756862030 300/600:5 3.0/2.0 60 86.7 0.3B-1.8/0.3B1.8 T100/T200 34.5 200 70 2.5
756862030 400/800:5 3.0/2.0 60 114 0.3B-1.8/0.3B1.8 T100/T200 34.5 200 70 2.5
756862030 500/1000:5 3.0/1.5 75 142.5 0.3B-1.8/0.3B1.8 T100/T200 34.5 200 70 2.5
756862030 600/1200:5 3.0/1.5 90 171 0.3B-1.8/0.3B1.8 T100/T200 34.5 200 70 2.5

756868040 200:5 4.0 20 38 0.15 B-1.8 - 34.5 200 70 2.5
756868120 600:5 3.0 60 86.7 0.15 B-1.8 - 34.5 200 70 2.5
756868200 1000:5 2.0 75 142.5 0.15 B-1.8 - 34.5 200 70 2.5
756868240 1200:5 1.5 90 171 0.15 B-1.8 - 34.5 200 70 2.5

CRK-36 34.5 kV CURRENT TRANSFORMER



requirements.
Resin Gray* 322 44.68 13.8
20.74 (527.50) 24.29 (617.46)
13.77 (350)
22.04 (562.32)
Secondary 1 Hole 9/16

terminals to ground
connection
Nameplate 13.77 (350)
H1 H2
MARKING X1 X2
CONNEC- (Single
TIONS Primary
Ratio)
1500 A 2000 A
H1 H2
Type: NEMA-4 Type: LZ-250 Type: Hex screw
Material: Copper Material: Copper Material: Steel


CRK-36 34.5 kV CURRENT TRANSFORMER
Power-Frequency
Ratio time time
(A) (kA/1s) (kApeak))
30C (kVrms) (kVrms)
756911001 5:5 1.5 0.5 0.95 0.3B-1.8 T400 34.5 200 70 2.5
756911002 10:5 1.5 1 1.9 0.3B-1.8 T400 34.5 200 70 2.5
756911003 15:5 1.5 1.5 2.85 0.3B-1.8 T400 34.5 200 70 2.5
756911004 20:5 1.5 2 3.8 0.3B-1.8 T400 34.5 200 70 2.5
756911005 25:5 1.5 2.5 4.75 0.3B-1.8 T400 34.5 200 70 2.5
756911006 30:5 1.5 3 5.7 0.3B-1.8 T400 34.5 200 70 2.5
756911008 40:5 1.5 4 7.6 0.3B-1.8 T400 34.5 200 70 2.5
756911010 50:5 1.5 5 9.5 0.3B-1.8 T400 34.5 200 70 2.5
756911015 75:5 1.5 6 11.4 0.3B-1.8 T400 34.5 200 70 2.5
756911020 100:5 1.5 7.5 14.25 0.3B-1.8 T400 34.5 200 70 2.5
756911030 150:5 1.5 10 19 0.3B-1.8 T400 34.5 200 70 2.5
756911040 200:5 1.5 20 38 0.3B-1.8 T400 34.5 200 70 2.5
756911060 300:5 1.5 30 57 0.3B-1.8 T400 34.5 200 70 2.5
756911080 400:5 1.5 40 76 0.3B-1.8 T400 34.5 200 70 2.5
756911100 500:5 1.5 50 9.5 0.3B-1.8 T400 34.5 200 70 2.5
756911120 600:5 1.5 60 86.7 0.3B-1.8 T400 34.5 200 70 2.5
756911160 800:5 1.5 60 114 0.3B-1.8 T400 34.5 200 70 2.5
756911200 1000:5 1.5 75 142.5 0.3B-1.8 T400 34.5 200 70 2.5
756911240 1200:5 1.5 90 171 0.3B-1.8 T400 34.5 200 70 2.5
756911400 2000:5 1.2 90 171 0.3B-1.8 T400 34.5 200 70 2.5
756911500 2500:5 1.2 90 171 0.3B-1.8 T400 34.5 200 70 2.5
756912002 10/20:5 3.0/1.5 2 3.8 0.3B-1.8/0.3B1.8 T200/T400 34.5 200 70 2.5
756912005 25/50:5 3.0/1.5 5 9.5 0.3B-1.8/0.3B1.8 T200/T400 34.5 200 70 2.5
756912006 30/60:5 3.0/1.5 6 11.4 0.3B-1.8/0.3B1.8 T200/T400 34.5 200 70 2.5
756912010 50/100:5 3.0/1.5 10 19 0.3B-1.8/0.3B1.8 T200/T400 34.5 200 70 2.5
756912015 75/150:5 3.0/1.5 15 28.5 0.3B-1.8/0.3B1.8 T200/T400 34.5 200 70 2.5
756912020 100/200:5 3.0/1.5 20 38 0.3B-1.8/0.3B1.8 T200/T400 34.5 200 70 2.5
756912030 150/300:5 3.0/1.5 30 57 0.3B-1.8/0.3B1.8 T200/T400 34.5 200 70 2.5
756912040 200/400:5 3.0/1.5 40 76 0.3B-1.8/0.3B1.8 T200/T400 34.5 200 70 2.5
756912060 300/600:5 3.0/1.5 60 86.7 0.3B-1.8/0.3B1.8 T200/T400 34.5 200 70 2.5
756912080 400/800:5 3.0/1.5 60 114 0.3B-1.8/0.3B1.8 T200/T400 34.5 200 70 2.5
756912100 500/1000:5 3.0/1.5 75 142.5 0.3B-1.8/0.3B1.8 T200/T400 34.5 200 70 2.5
756912120 600/1200:5 3.0/1.5 90 171 0.3B-1.8/0.3B1.8 T200/T400 34.5 200 70 2.5
756912150 750/1500:5 3.0/1.5 90 171 0.3B-1.8/0.3B1.8 T200/T400 34.5 200 70 2.5
756912200 1000/2000:5 2.4/1.2 90 171 0.3B-1.8/0.3B1.8 T200/T400 34.5 200 70 2.5

CE-046 46 kV CURRENT TRANSFORMER

OUTDOOR
control.

requirements.
Resin Gray* 595 75.2 22
16.14 (410) 37.87 (962)
H2 H1 (4)9/16 (14.2)
9.84 (250)
51.18 (1300)
Terminal 9.84 (250)

box Ground
connector
H1 H2
MARKING X1 X2
CONNEC- (Single
TIONS Primary
Ratio)
H1 H2


Power-Frequency
Ratio time time
30C (kVrms) (kVrms)
756162005 25/50:5 3.0/2.0 5 9.5 0.3B-1.8/0.3B1.8 T200/T400 46 250 95 2.5

756162006 30/60:5 3.0/2.0 6 11.4 0.3B-1.8/0.3B1.8 T200/T400 46 250 95 2.5
756162010 50/100:5 3.0/2.0 10 19 0.3B-1.8/0.3B1.8 T200/T400 46 250 95 2.5
756162015 75/150:5 3.0/2.0 15 28.5 0.3B-1.8/0.3B1.8 T200/T400 46 250 95 2.5
756162020 100/200:5 3.0/2.0 20 38 0.3B-1.8/0.3B1.8 T200/T400 46 250 95 2.5
756162030 150/300:5 3.0/2.0 30 57 0.3B-1.8/0.3B1.8 T200/T400 46 250 95 2.5
756162040 200/400:5 3.0/2.0 40 76 0.3B-1.8/0.3B1.8 T200/T400 46 250 95 2.5
756162060 300/600:5 3.0/2.0 60 86.7 0.3B-1.8/0.3B1.8 T200/T400 46 250 95 2.5
756162080 400/800:5 3.0/2.0 60 114 0.3B-1.8/0.3B1.8 T200/T400 46 250 95 2.5
756162100 500/1000:5 3.0/1.5 75 142.5 0.3B-1.8/0.3B1.8 T200/T400 46 250 95 2.5
756162120 600/1200:5 3.0/1.5 90 171 0.3B-1.8/0.3B1.8 T200/T400 46 250 95 2.5
756162150 750/1500:5 3.0/1.5 90 171 0.3B-1.8/0.3B1.8 T200/T400 46 250 95 2.5
756162200 1000/2000:5 2.4/1.2 90 171 0.3B-1.8/0.3B1.8 T400/T800 46 250 95 2.5
756162300 1500/3000:5 2.4/1.2 90 171 0.3B-1.8/0.3B1.8 T400/T800 46 250 95 2.5

756166040 200:5 1.5 16 40 0.15 B-1.8 - 46 250 95 2.5
756166120 600:5 1.5 48 120 0.15 B-1.8 - 46 250 95 2.5
756166200 1000:5 1.5 50 125 0.15 B-1.8 - 46 250 95 2.5
756166240 1200:5 1.5 96 240 0.15 B-1.8 - 46 250 95 2.5
Notes:

CRH-52 46 kV CURRENT TRANSFORMER



requirements.
Resin Gray* 253.53 47.83 23
15.31 (385)
Nameplate
9.84 (250)
24.68 (626.87)
Lifting holes
Terminal secondary
box with NPT 1
Hole 9/16 to ground
Quick Connector
connection
9.84 (250)
H1 H2
MARKING X1 X2
CONNEC- (Single
TIONS Primary
Ratio)
H1 H2


Power-Frequency
Ratio time time
30C (kVrms) (kVrms)
756872005 25/50:5 2.4/1.2 5 9.5 0.3B-1.8/0.3B1.8 T100/T200 46 250 95 2.5

756872006 30/60:5 2.4/1.2 6 11.4 0.3B-1.8/0.3B1.8 T100/T200 46 250 95 2.5
756872010 50/100:5 2.4/1.2 10 19 0.3B-1.8/0.3B1.8 T100/T200 46 250 95 2.5
756872015 75/150:5 2.4/1.2 15 28.5 0.3B-1.8/0.3B1.8 T100/T200 46 250 95 2.5
756872020 100/200:5 2.4/1.2 20 38 0.3B-1.8/0.3B1.8 T100/T200 46 250 95 2.5
756872030 150/300:5 2.4/1.2 30 57 0.3B-1.8/0.3B1.8 T100/T200 46 250 95 2.5
756872040 200/400:5 2.4/1.2 40 76 0.3B-1.8/0.3B1.8 T100/T200 46 250 95 2.5
756872060 300/600:5 2.4/1.2 60 86.7 0.3B-1.8/0.3B1.8 T100/T200 46 250 95 2.5
756872080 400/800:5 2.4/1.2 60 114 0.3B-1.8/0.3B1.8 T100/T200 46 250 95 2.5
756872100 500/1000:5 2.4/1.2 75 142.5 0.3B-1.8/0.3B1.8 T100/T200 46 250 95 2.5
756872120 600/1200:5 2.4/1.2 90 171 0.3B-1.8/0.3B1.8 T100/T200 46 250 95 2.5

756876040 200:5 1.5 16 40 0.15 B-1.8 - 46 250 95 2.5
756876120 600:5 1.5 48 120 0.15 B-1.8 - 46 250 95 2.5
756876200 1000:5 1.5 50 125 0.15 B-1.8 - 46 250 95 2.5
756876240 1200:5 1.5 96 240 0.15 B-1.8 - 46 250 95 2.5
Notes:

CRK-52 46 kV CURRENT TRANSFORMER



requirements.
Resin Gray* 458 63.62 19.7
20.74 (527.5) 24.29 (615.96)
13.77 (350)
28.20 (716.20)
Lifting holes
Secondary
1 Hole 9/16 to 2 Holes 1
terminals
ground connector to conduit
pipe NPT
13.77 (350)
Nameplate
H1 H2
MARKING X1 X2
CONNEC- (Single
TIONS Primary
Ratio)
1500 A 2000 A
H1 H2


Power-Frequency
Ratio time time
30C (kVrms) (kVrms)
756922005 25/50:5 3.0/1.5 5 9.5 0.3B-1.8/0.3B1.8 T200/T400 46 250 95 2.5

756922006 30/60:5 3.0/1.5 6 11.4 0.3B-1.8/0.3B1.8 T200/T400 46 250 95 2.5
756922010 50/100:5 3.0/1.5 10 19 0.3B-1.8/0.3B1.8 T200/T400 46 250 95 2.5
756922015 75/150:5 3.0/1.5 15 28.5 0.3B-1.8/0.3B1.8 T200/T400 46 250 95 2.5
756922020 100/200:5 3.0/1.5 20 38 0.3B-1.8/0.3B1.8 T200/T400 46 250 95 2.5
756922030 150/300:5 3.0/1.5 30 57 0.3B-1.8/0.3B1.8 T200/T400 46 250 95 2.5
756922040 200/400:5 3.0/1.5 40 76 0.3B-1.8/0.3B1.8 T200/T400 46 250 95 2.5
756922060 300/600:5 3.0/1.5 60 86.7 0.3B-1.8/0.3B1.8 T200/T400 46 250 95 2.5
756922080 400/800:5 3.0/1.5 60 114 0.3B-1.8/0.3B1.8 T200/T400 46 250 95 2.5
756922100 500/1000:5 3.0/1.5 75 142.5 0.3B-1.8/0.3B1.8 T200/T400 46 250 95 2.5
756922120 600/1200:5 3.0/1.5 90 171 0.3B-1.8/0.3B1.8 T200/T400 46 250 95 2.5
756922150 750/1500:5 3.0/1.5 90 171 0.3B-1.8/0.3B1.8 T200/T400 46 250 95 2.5
756922200 1000/2000:5 2.4/1.2 90 171 0.3B-1.8/0.3B1.8 T200/T400 46 250 95 2.5
Notes:


OUTDOOR
control.

requirements.
Resin Gray* 771 109.4 33
16.14 (410) 35.5 (902)
H2 H1
13.78 (350)
62 (1576)
13.78 (350)
Terminal
Ground
box
connector
H1 H2
MARKING X1 X2
CONNEC- (Single
TIONS Primary
Ratio)
H1 H2


Power-Frequency
Ratio time time
30C (kVrms) (kVrms)
756172005 25/50:5 2.4/1.2 5 9.5 0.3B-1.8/0.3B1.8 T200/T400 69 350 140 2.5

756172006 30/60:5 2.4/1.2 6 11.4 0.3B-1.8/0.3B1.8 T200/T400 69 350 140 2.5
756172010 50/100:5 2.4/1.2 10 19 0.3B-1.8/0.3B1.8 T200/T400 69 350 140 2.5
756172015 75/150:5 2.4/1.2 15 28.5 0.3B-1.8/0.3B1.8 T200/T400 69 350 140 2.5
756172020 100/200:5 2.4/1.2 20 38 0.3B-1.8/0.3B1.8 T200/T400 69 350 140 2.5
756172030 150/300:5 2.4/1.2 30 57 0.3B-1.8/0.3B1.8 T200/T400 69 350 140 2.5
756172040 200/400:5 2.4/1.2 40 76 0.3B-1.8/0.3B1.8 T200/T400 69 350 140 2.5
756172060 300/600:5 2.4/1.2 60 86.7 0.3B-1.8/0.3B1.8 T200/T400 69 350 140 2.5
756172080 400/800:5 2.4/1.2 60 114 0.3B-1.8/0.3B1.8 T200/T400 69 350 140 2.5
756172100 500/1000:5 2.4/1.2 75 142.5 0.3B-1.8/0.3B1.8 T200/T400 69 350 140 2.5
756172120 600/1200:5 2.4/1.2 90 171 0.3B-1.8/0.3B1.8 T200/T400 69 350 140 2.5
756172150 750/1500:5 2.4/1.2 90 171 0.3B-1.8/0.3B1.8 T200/T400 69 350 140 2.5
756172200 1000/2000:5 2.4/1.2 90 171 0.3B-1.8/0.3B1.8 T400/T800 69 350 140 2.5
756172300 1500/3000:5 2.4/1.2 90 171 0.3B-1.8/0.3B1.8 T400/T800 69 350 140 2.5

756176040 200:5 1.5 16 40 0.15 B-1.8 - 69 350 140 2.5
756176120 600:5 1.5 48 120 0.15 B-1.8 - 69 350 140 2.5
756176200 1000:5 1.5 50 125 0.15 B-1.8 - 69 350 140 2.5
756176240 1200:5 1.5 96 240 0.15 B-1.8 - 69 350 140 2.5
Notes:




requirements.
Resin Gray* 298 74.8 26
15.31 (389) 15.31 (385)
9.84 (250)
30.7 (780)
Hole 9/16
to ground Terminal
connection Lifting holes secondary box
3/4 with 1 NPT 9.84 (250)
H1 H2
MARKING X1 X2
CONNEC- (Single
TIONS Primary
Ratio)
H1 H2


Power-Frequency
Ratio time time
30C (kVrms) (kVrms)
756892005 25/50:5 2.4/1.2 5 9.5 0.3B-1.8/0.3B1.8 T100/T200 69 350 140 2.5

756892006 30/60:5 2.4/1.2 6 11.4 0.3B-1.8/0.3B1.8 T100/T200 69 350 140 2.5
756892010 50/100:5 2.4/1.2 10 19 0.3B-1.8/0.3B1.8 T100/T200 69 350 140 2.5
756892015 75/150:5 2.4/1.2 15 28.5 0.3B-1.8/0.3B1.8 T100/T200 69 350 140 2.5
756892020 100/200:5 2.4/1.2 20 38 0.3B-1.8/0.3B1.8 T100/T200 69 350 140 2.5
756892030 150/300:5 2.4/1.2 30 57 0.3B-1.8/0.3B1.8 T100/T200 69 350 140 2.5
756892040 200/400:5 2.4/1.2 40 76 0.3B-1.8/0.3B1.8 T100/T200 69 350 140 2.5
756892060 300/600:5 2.4/1.2 60 86.7 0.3B-1.8/0.3B1.8 T100/T200 69 350 140 2.5
756892080 400/800:5 2.4/1.2 60 114 0.3B-1.8/0.3B1.8 T100/T200 69 350 140 2.5
756892100 500/1000:5 2.4/1.2 75 142.5 0.3B-1.8/0.3B1.8 T100/T200 69 350 140 2.5
756892120 600/1200:5 2.4/1.2 90 171 0.3B-1.8/0.3B1.8 T100/T200 69 350 140 2.5
756176040 200:5 1.5 16 40 0.15 B-1.8 - 69 350 140 2.5
756176120 600:5 1.5 48 120 0.15 B-1.8 - 69 350 140 2.5
756176200 1000:5 1.5 50 125 0.15 B-1.8 - 69 350 140 2.5
756176240 1200:5 1.5 96 240 0.15 B-1.8 - 69 350 140 2.5
Notes:




requirements.
Resin Gray* 518 91.2 26.2
20.74 (527.5) 24.29 (615.96)

M12
13.77 (350)
34.44 (875.05)
Lifting holes
Secondary 1 Hole 9/16 to

terminal box ground connector 2 Holes 1
to conduit
pipe NPT 13.77 (350)
Nameplate
H1 H2
MARKING X1 X2
CONNEC- (Single
TIONS Primary
Ratio)
1500 A 2000 A
H1 H2


Power-Frequency
Ratio time time
30C (kVrms) (kVrms)
756932005 25/50:5 2.4/1.2 5 9.5 0.3B-1.8/0.3B1.8 T200/T400 69 350 140 2.5

756932006 30/60:5 2.4/1.2 6 11.4 0.3B-1.8/0.3B1.8 T200/T400 69 350 140 2.5
756932010 50/100:5 2.4/1.2 10 19 0.3B-1.8/0.3B1.8 T200/T400 69 350 140 2.5
756932015 75/150:5 2.4/1.2 15 28.5 0.3B-1.8/0.3B1.8 T200/T400 69 350 140 2.5
756932020 100/200:5 2.4/1.2 20 38 0.3B-1.8/0.3B1.8 T200/T400 69 350 140 2.5
756932030 150/300:5 2.4/1.2 30 57 0.3B-1.8/0.3B1.8 T200/T400 69 350 140 2.5
756932040 200/400:5 2.4/1.2 40 76 0.3B-1.8/0.3B1.8 T200/T400 69 350 140 2.5
756932060 300/600:5 2.4/1.2 60 86.7 0.3B-1.8/0.3B1.8 T200/T400 69 350 140 2.5
756932080 400/800:5 2.4/1.2 60 114 0.3B-1.8/0.3B1.8 T200/T400 69 350 140 2.5
756932100 500/1000:5 2.4/1.2 75 142.5 0.3B-1.8/0.3B1.8 T200/T400 69 350 140 2.5
756932120 600/1200:5 2.4/1.2 90 171 0.3B-1.8/0.3B1.8 T200/T400 69 350 140 2.5
756932150 750/1500:5 2.4/1.2 90 171 0.3B-1.8/0.3B1.8 T400/T800 69 350 140 2.5
756932200 1000/2000:5 2.4/1.2 90 171 0.3B-1.8/0.3B1.8 T400/T800 69 350 140 2.5
Notes:

KM-15 15 kV COMBINED TRANSFORMER
ARTECHE KM series are dry type outdoor service combination CT-PT. The
internal dielectric properties and mechanical strength. The external layer
of Cycloaliphatic Epoxy Resin (CEP) provides resistance to ultraviolet rays
and the effects of tracking and erosion on the exterior of the transformer
maintenance free.
OUTDOOR

requirements.
Resin Gray* 209 23.7 13
14 (356) Nameplate
13 (330)
22 (559)

pipe 1 to ground
connection 10 (254)
H1 H2

/4
1
C1 C2
H0
MARKING
V1 V2
CONNEC- (Single
Type: NEMA-2 Type: TE-12 250 Type: Quick Connector
TIONS Material: Copper Material: Copper Material: Brass Primary ONE SECONDARY
Range: 4TRE-250MCM Ratio) with tap
H1 H2
C1 C2 C3
H0
V1 V2

*Brown color available upon request

Power-Frequency
Short- Short- IEEE
Current Thermal IEEE Metering Nominal (1 min)
time time Metering
Code * Ratio Current Accuracy Voltage BIL
Thermal Mechanical Accuracy
(CEP) (Primary: Rating [Voltage System (kV) Primary & Secondary
Current Current [Current
Secondary) Factor @ Transformer] (kV) Secondary Winding
(kA/1s) (kApeak) Transformer]
30C (kVrms) (kVrms)
770083011 5:5 3.0 0,5 1.4 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 15 110 34 2.5
770083021 10:5 3.0 1 2.7 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 15 110 34 2.5
770083031 15:5 3.0 1.5 4.1 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 15 110 34 2.5
770083041 20:5 3.0 2 5.4 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 15 110 34 2.5
770083051 25:5 3.0 2.5 6.8 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 15 110 34 2.5
770083061 30:5 3.0 3 8.1 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 15 110 34 2.5
770083071 40:5 3.0 4 10.8 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 15 110 34 2.5
770083081 50:5 3.0 5 13.5 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 15 110 34 2.5
770083091 75:5 3.0 7.5 20.3 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 15 110 34 2.5
770083101 100:5 3.0 10 27 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 15 110 34 2.5
770083111 150:5 3.0 15 40.5 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 15 110 34 2.5
770083121 200:5 3.0 20 54 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 15 110 34 2.5
770083131 300:5 3.0 30 81 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 15 110 34 2.5
770083141 400:5 3.0 40 108 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 15 110 34 2.5
770083151 600:5 2.0 60 162 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 15 110 34 2.5
770083161 800:5 1.5 60 162 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 15 110 34 2.5
770083171 1000:5 1.2 60 162 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 15 110 34 2.5
770083181 1200:5 1.0 60 162 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 15 110 34 2.5
770084041 10/20:5 2.0/1.5 2 5 0.3 B0.2/B-0.5 0.3 W,X,M,Y/0.6Z 15 110 34 2.5
770084081 25/50:5 2.0/1.5 5 12.5 0.3 B0.2/B-0.5 0.3 W,X,M,Y/0.6Z 15 110 34 2.5
770084121 100/200:5 2.0/1.5 20 50 0.3 B0.2/B-0.5 0.3 W,X,M,Y/0.6Z 15 110 34 2.5
770084151 300/600:5 2.0/1.5 60 150 0.3 B0.2/B-0.5 0.3 W,X,M,Y/0.6Z 15 110 34 2.5
770084161 400/800:5 2.0/1.5 60 150 0.3 B0.2/B-0.5 0.3 W,X,M,Y/0.6Z 15 110 34 2.5
770083161 400/800:5 3.0/1.5 60 150 0.3 B0.2/B-0.5 0.3 W,X,M,Y/0.6Z 15 110 34 2.5
770084171 500/1000:5 2.0/1.2 75 127.5 0.3 B0.2/B-0.5 0.3 W,X,M,Y/0.6Z 15 110 34 2.5
770084181 600/1200:5 2.0/1.0 90 162 0.3 B0.2/B-0.5 0.3 W,X,M,Y/0.6 Z 15 110 34 2.5

770087121 200:5 3.0 20 50 0.15 B-0.5 0.3 W,X,M,Y/0.6Z 15 110 34 2.5
770088121 200:5 1.5 20 50 0.15 B-1.8 0.3 W,X,M,Y/0.6Z 15 110 34 2.5
770088171 1000:5 1.5 75 127.5 0.15 B-1.8 0.3 W,X,M,Y/0.6Z 15 110 34 2.5

Rated
VT Secondary Voltage
Primary (V) Burden Voltage Factor
Ratio (V) Factor 30s
(VA) (Un)
(Un)
60:1 7200/12470GY 120 750 1.25 1.5

MK-15 15 kV METERING UNIT
ARTECHE ME/MK series metering units are outdoor, three-phase, pole-

mounted metering racks.
The rack is made of lightweight aluminium designed to mount on poles

in an upright position. It includes two galvanized steel mounting bolts for
attaching the metering unit to the pole, with pole diameters available from
8 to 14. Optional galvanized steel structures and/or other pole diameters
are available upon request.
MK series incorporate 3 combined transformers mounted vertically. Their

The external layer can be manufactured with Hydrophobic Cycloaliphatic

OUTDOOR The core is built with high permeability grain oriented silicon steel
60 Hertz laminations for low losses. The windings are copper wire with copper plate

requirements.
Resin Gray* 692 23.7 13
33.5 (851)
32.1 (815)
32.1 (815) 53.1 (1349)

PRIMARY TERMINAL GROUND CONNECTOR CONNECTION PLATE
L3 H1 H2
L2 H1 H2
L1 H1 H2
H1 H2 H1 H2 H1 H2
X1 X2 X1 X2 X1 X2
Type: NEMA-2 Type: TE-12 250 Material: Copper X1 X2 X1 X2 X1 X2

Material: Copper Range: 4TRE-250MCM VT1 VT2 VT3 CT1 CT2 CT3
CONNEC-
MARKING
TIONS SECONDARY TERMINAL

1 2 3 4 5 6 7 8 9 10
/4
1
Type: Quick Connector Material: Brass


Power-Frequency
Short- Short- IEEE
time time Metering
30C (kVrms) (kVrms)
770663011 5:5 3.0 0,5 1.4 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 15 110 34 2.5
770663021 10:5 3.0 1 2.7 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 15 110 34 2.5
770663031 15:5 3.0 1.5 4.1 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 15 110 34 2.5
770663041 20:5 3.0 2 5.4 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 15 110 34 2.5
770663051 25:5 3.0 2.5 6.8 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 15 110 34 2.5
770663061 30:5 3.0 3 8.1 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 15 110 34 2.5
770663071 40:5 3.0 4 10.8 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 15 110 34 2.5
770663081 50:5 3.0 5 13.5 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 15 110 34 2.5
770663091 75:5 3.0 7.5 20.3 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 15 110 34 2.5
770663101 100:5 3.0 10 27 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 15 110 34 2.5
770663111 150:5 3.0 15 40.5 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 15 110 34 2.5
770663121 200:5 3.0 20 54 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 15 110 34 2.5
770663131 300:5 3.0 30 81 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 15 110 34 2.5
770663141 400:5 3.0 40 108 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 15 110 34 2.5
770663151 600:5 2.0 60 162 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 15 110 34 2.5
770663161 800:5 1.5 60 162 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 15 110 34 2.5
770663171 1000:5 1.2 60 162 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 15 110 34 2.5
770663181 1200:5 1.0 60 162 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 15 110 34 2.5

770667121 200:5 3.0 20 50 0.15 B-0.5 0.3 W,X,M,Y/0.6Z 15 110 34 2.5
770668121 200:5 1.5 20 50 0.15 B-1.8 0.3 W,X,M,Y/0.6Z 15 110 34 2.5
770668171 1000:5 1.5 75 127.5 0.15 B-1.8 0.3 W,X,M,Y/0.6Z 15 110 34 2.5

Rated
Secondary Voltage
(V) Factor 30s
(VA) (Un)
(Un)
60:1 7200/12470GY 120 750 1.25 1.5

ME-015 15 kV METERING UNIT
ARTECHE ME/MK series metering units are outdoor. three-phase. pole-


attaching the metering unit to the pole. with pole diameters available from
ME series incorporate 3 current transformers mounted vertically and 3

voltage transformers mounted horizontally. Their core is encapsulated with
Type B epoxy resin which provides excellent internal dielectric properties
and mechanical strength. The external layer of Cycloaliphatic Epoxy Resin
(CEP) provides resistance to ultraviolet rays and the effects of tracking and
erosion on the exterior of the transformer ensuring a long mechanical and
electrical life. The transformer is maintenance free.

OUTDOOR
60 Hertz
ux leakage. achieving greater accuracy and higher capacity to withstand

requirements.
Y
Z
W
PRIMARY TERMINAL CT PRIMARY TERMINAL VT GROUND CONNECTOR SECONDARY TERMINAL

/4
1
CONNEC-
TIONS
Type: NEMA-2 Type: TE-4T Type: TE-12-250 Type: Quick Connector


Characteristics
Transformers Code * (CEP) Dimensions (in)
Weigth with
Type With FUSE in the Without FUSE in Aluminium
Current Potential W X Y Z rack (lb)
secondary box the secondary box
ME-015 CRB-17 URL-17 771000009 771000017 82 32.25 58 48.75 520

ME-015 CRB-17 VRL-17 771000010 771000018 81.19 32.25 57.43 48.31 531
ME-015 CRB-17 URJ-17 771000011 771000019 80.5 32.50 56.87 47.94 564
ME-015 CRB-17 VRJ-17 771000012 771000020 81 32.50 57.31 48.25 564
ME-015 CRE-17 URL-17 771000013 771000021 82 32.68 58 48.75 579
ME-015 CRE-17 VRL-17 771000014 771000022 81.19 32.68 57.43 48.31 590
ME-015 CRE-17 URJ-17 771000015 771000023 80.5 32.68 56.87 47.94 623
ME-015 CRE-17 VRJ-17 771000016 771000024 81 32.68 57.31 48.25 623
For detail electric characteristics see particular instrument transformer detail in its data sheet within this publication.
Notes:

MI-015 15 kV METERING UNIT
ARTECH MI series metering units are outdoor, three-phase, pad-mounted

ARTECHE
cabinets.
The cabin
cabinet is made of #12 caliber stainless steel lamination (2.7 mm or 0.105
in) with M
Munsell Green #7GY 3.29/1.5 powder nish. The doors are pad-
lockable with a three point latch and a penta-head bolt.
MI series incorporate 3 combined transformers. Their core is encapsulated

with Type B epoxy resin which provides excellent internal dielectric
propertie
properties and mechanical strength, ensuring a long mechanical and
The entire
entir surface of the transformer is coated with a conductive layer that
is intende
intended to be solidly grounded when energized. This allows for compact
laminatio
double is
isolation. The concentric distribution of the coils prevents magnetic
OUTDOOR mechanical stresses in adverse operating conditions.
60 Hertz
Partial Discharge measurements exceed the IEEE, CAN/CSA and
IECrequirements.
The primary bushing well connections are IEEE 386 compliant, rated 200 A
loadbreak or 600 A non load-break.. The secondary terminals are pre-wired to
a 10 position test switch and 9S meter socket in standard red/black colors.
Material Colors Weight (lbs.)
Stainless steel Munsell Green 992
8 x 0.75
(4) Lifting plates
W/5/8 - 11 Bolts
13
8 x 1.22
Air spring
35.2
38
32.28
4.5
26 44
50 45
L3 H1 H2
L2 H1 H2
L1 H1 H2
H1 H2 H1 H2 H1 H2
X1 X2 X1 X2 X1 X2
X1 X2 X1 X2 X1 X2
VT1 VT2 VT3 CT1 CT2 CT3
MARKING
1 2 3 4 5 6 7 8 9 10

Power-Frequency
Short- Short- IEEE
time time Metering
Ratio Current Accuracy Voltage BIL
Code Thermal Mechanical Accuracy
(Primary: Rating [Voltage System (kV) Primary & Secondary
30C (kVrms) (kVrms)
770574011 5:5 2.0 0.5 1.25 0.3 B-0.5 0.3 W,X,M,Y/1.2Z 15 110 34 2.5
770574021 10:5 2.0 1 2.5 0.3 B-0.5 0.3 W,X,M,Y/1.2Z 15 110 34 2.5
770574031 15:5 2.0 1.5 3.75 0.3 B-0.5 0.3 W,X,M,Y/1.2Z 15 110 34 2.5
770574041 20:5 2.0 2 5 0.3 B-0.5 0.3 W,X,M,Y/1.2Z 15 110 34 2.5
770574051 25:5 2.0 2.5 6.25 0.3 B-0.5 0.3 W,X,M,Y/1.2Z 15 110 34 2.5
770574061 30:5 2.0 3 7.5 0.3 B-0.5 0.3 W,X,M,Y/1.2Z 15 110 34 2.5
770574081 40:5 2.0 4 10 0.3 B-0.5 0.3 W,X,M,Y/1.2Z 15 110 34 2.5
770574101 50:5 2.0 5 12.5 0.3 B-0.5 0.3 W,X,M,Y/1.2Z 15 110 34 2.5
770574151 75:5 2.0 7.5 18.75 0.3 B-0.5 0.3 W,X,M,Y/1.2Z 15 110 34 2.5
770574201 100:5 2.0 10 25 0.3 B-0.5 0.3 W,X,M,Y/1.2Z 15 110 34 2.5
770575301 150:5 1.33 10 25 0.3 B-0.5 0.3 W,X,M,Y/1.2Z 15 110 34 2.5
770575401 200:5 1.0 10 25 0.3 B-0.5 0.3 W,X,M,Y/1.2Z 15 110 34 2.5
770571131 300:5 1.5 30 75 0.3 B-0.5 0.3 W,X,M,Y/1.2Z 15 110 34 2.5
770571141 400:5 1.5 40 100 0.3 B-0.5 0.3 W,X,M,Y/1.2Z 15 110 34 2.5
770571151 600:5 1.0 60 150 0.3 B-0.5 0.3 W,X,M,Y/1.2Z 15 110 34 2.5

770571101 100:5 2.0 10 25 0.15 B-0.5 0.3 W,X,M,Y/1.2Z 15 110 34 2.5
770571121 200:5 2.0 20 50 0.15 B-0.5 0.3 W,X,M,Y/1.2Z 15 110 34 2.5
770571151 600:5 1.0 48 120 0.15 B-0.5 0.3 W,X,M,Y/1.2Z 15 110 34 2.5

Rated
Secondary Voltage
(V) Factor 30s
(VA) (Un)
(Un)
60:1 7200/12470GY 120 750 1.1 1.25

maintenance free.
OUTDOOR
Partial Discharge measurements exceed IEEE C57.13 2008 requirements
Resin Gray* 230 32.6 16
14 (356) Nameplate
13 (330)
24.5 (622)
Lifting
Holes
pipe 1 to ground 10 (254)
connection
H1 H2

/4
1
C1 C2
H0
MARKING
V1 V2
CONNEC- (Single
H1 H2
C1 C2 C3
H0
V1 V2


Power-Frequency
Short- Short- IEEE
time time Metering
30C (kVrms) (kVrms)
770061016 5:5 1.5 0.5 1.4 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 25 150 50 2.5
770061026 10:5 1.5 1 2.7 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 25 150 50 2.5
770061036 15:5 1.5 1.5 4.1 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 25 150 50 2.5
770061046 20:5 1.5 2 5.4 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 25 150 50 2.5
770061056 25:5 1.5 2.5 6.8 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 25 150 50 2.5
770061066 30:5 1.5 3 8.1 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 25 150 50 2.5
770061076 40:5 1.5 4 10.8 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 25 150 50 2.5
770061086 50:5 1.5 5 13.5 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 25 150 50 2.5
770061096 75:5 1.5 7.5 20.3 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 25 150 50 2.5
770061106 100:5 1.5 10 27 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 25 150 50 2.5
770061116 150:5 1.5 15 40.5 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 25 150 50 2.5
770061126 200:5 1.5 20 54 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 25 150 50 2.5
770061136 300:5 1.5 30 81 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 25 150 50 2.5
770061146 400:5 1.5 40 108 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 25 150 50 2.5
770061156 600:5 1.0 60 162 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 25 150 50 2.5
770061166 800:5 1.0 60 162 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 25 150 50 2.5
770061176 1000:5 1.0 60 162 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 25 150 50 2.5
770061186 1200:5 1.0 60 162 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 25 150 50 2.5
770064046 10/20:5 2.0/1.5 2 5 0.3 B0.2/B-0.5 0.3 W,X,M,Y/0.6Z 25 150 50 2.5
770064086 25/50:5 2.0/1.5 5 12.5 0.3 B0.2/B-0.5 0.3 W,X,M,Y/0.6Z 25 150 50 2.5
770064126 100/200:5 2.0/1.5 20 50 0.3 B0.2/B-0.5 0.3 W,X,M,Y/0.6Z 25 150 50 2.5
770064136 150/300:5 2.0/1.5 30 75 0.3 B0.2/B-0.5 0.3 W,X,M,Y/0.6Z 25 150 50 2.5
770066136 150/300:5 4.0/2.0 30 75 0.3 B0.2/B-0.5 0.3 W,X,M,Y/0.6Z 25 150 50 2.5
770064156 300/600:5 2.0/1.5 60 150 0.3 B0.2/B-0.5 0.3 W,X,M,Y/0.6Z 25 150 50 2.5
770064176 500/1000:5 2.0/1.2 75 127.5 0.3 B0.2/B-0.5 0.3 W,X,M,Y/0.6Z 25 150 50 2.5
770064186 600/1200:5 2.0/1.0 90 162 0.3 B0.2/B-0.5 0.3 W,X,M,Y/0.6Z 25 150 50 2.5

770067126 200:5 3.0 20 50 0.15 B-0.5 0.3 W,X,M,Y/0.6Z 25 150 50 2.5
770068126 200:5 1.5 20 50 0.15 B-1.8 0.3 W,X,M,Y/0.6Z 25 150 50 2.5
770068176 1000:5 1.5 75 127.5 0.15 B-1.8 0.3 W,X,M,Y/0.6Z 25 150 50 2.5

Rated
Secondary Voltage
(V) Factor
(VA) (Un)
30s (Un)
120:1 14400/24940GY 120 750 1.25 1.5





OUTDOOR laminations for low losses. The windings are copper wire with copper plate

requirements.
Resin Gray* 755 32.6 16
36.17 (919.5)
32.1 (815)
32.1 (815) 53.15 (1349)

L3 H1 H2
L2 H1 H2
L1 H1 H2
H1 H2 H1 H2 H1 H2
X1 X2 X1 X2 X1 X2
Type: NEMA-2 Type: TE-12 250 Material: Copper
Material: Copper Range: 4TRE-250MCM X1 X2 X1 X2 X1 X2
CONNEC- VT1 VT2 VT3 CT1 CT2 CT3
MARKING

/4
1 2 3 4 5 6 7 8 9 10
1


Power-Frequency
Short- Short- IEEE
time time Metering
30C (kVrms) (kVrms)
770681016 5:5 1.5 0.5 1.4 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 25 150 50 2.5
770681026 10:5 1.5 1 2.7 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 25 150 50 2.5
770681036 15:5 1.5 1.5 4.1 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 25 150 50 2.5
770681046 20:5 1.5 2 5.4 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 25 150 50 2.5
770681056 25:5 1.5 2.5 6.8 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 25 150 50 2.5
770681066 30:5 1.5 3 8.1 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 25 150 50 2.5
770681076 40:5 1.5 4 10.8 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 25 150 50 2.5
770681086 50:5 1.5 5 13.5 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 25 150 50 2.5
770681096 75:5 1.5 7.5 20.3 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 25 150 50 2.5
770681106 100:5 1.5 10 27 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 25 150 50 2.5
770681116 150:5 1.5 15 40.5 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 25 150 50 2.5
770681126 200:5 1.5 20 54 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 25 150 50 2.5
770681136 300:5 1.5 30 81 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 25 150 50 2.5
770681146 400:5 1.5 40 108 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 25 150 50 2.5
770681156 600:5 1.0 60 162 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 25 150 50 2.5
770681166 800:5 1.0 60 162 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 25 150 50 2.5
770681176 1000:5 1.0 60 162 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 25 150 50 2.5
770681186 1200:5 1.0 60 162 0.3 B-0.5 0.3 W,X,M,Y/0.6Z 25 150 50 2.5

770687126 200:5 3.0 20 50 0.15 B-0.5 0.3 W,X,M,Y/0.6Z 25 150 50 2.5
770688126 200:5 1.5 20 50 0.15 B-1.8 0.3 W,X,M,Y/0.6Z 25 150 50 2.5
770688176 1000:5 1.5 75 127.5 0.15 B-1.8 0.3 W,X,M,Y/0.6Z 25 150 50 2.5

Rated
Secondary Voltage
(V) Factor
(VA) (Un)
30s (Un)
120:1 14400/24940GY 120 750 1.25 1.5





OUTDOOR
60 Hertz

requirements.
Y
Z
W

/4
1
CONNEC-
TIONS


Characteristics
Weigth with
ME-025 CRE-24 URJ-24 771020005 771020009 91 35.31 64.43 53.25 648

ME-025 CRE-24 VRJ-24 771020006 771020010 90.5 35.31 64.43 53 666
ME-025 CRF-24 URN-24 771020007 771020011 87.5 34.25 61.81 51.5 881
ME-025 CRF-24 VRN-24 771020008 771020012 87.34 34.25 61.81 51.5 881
Notes:

ARTECH MI series metering units are outdoor, three-phase, pad-mounted

ARTECHE
cabinets.
The cabin
cabinet is made of #12 caliber stainless steel lamination (2.7 mm or 0.105
in) with M
Munsell Green #7GY 3.29/1.5 powder nish. The doors are pad-
lockable with a three point latch and a penta-head bolt.
MI series incorporate 3 combined transformers. Their core is encapsulated

with Type B epoxy resin which provides excellent internal dielectric
propertie
properties and mechanical strength, ensuring a long mechanical and
The entire
entir surface of the transformer is coated with a conductive layer that
is intende
intended to be solidly grounded when energized. This allows for compact
laminatio
double is
isolation. The concentric distribution of the coils prevents magnetic
OUTDOOR mechanical stresses in adverse operating conditions.
60 Hertz
requirements.
The primary bushing well connections are IEEE 386 compliant, rated 200 A
loadbreak or 600 A non load-break. The secondary terminals are pre-wired
to a 10 position test switch and 9S meter socket in standard red/blackcolors.
Material Colors Weight (lbs.)
Stainless steel Munsell Green 992
8 x 0.75
(4) Lifting plates
W/5/8 - 11 Bolts
13
8 x 1.22
Air spring
35.2
38
32.28
4.5
26 44
50 45
L3 H1 H2
L2 H1 H2
L1 H1 H2
H1 H2 H1 H2 H1 H2
X1 X2 X1 X2 X1 X2
X1 X2 X1 X2 X1 X2
VT1 VT2 VT3 CT1 CT2 CT3
MARKING
1 2 3 4 5 6 7 8 9 10

Power-Frequency
Short- Short- IEEE
time time Metering
Ratio Current Accuracy Voltage BIL
Code Thermal Mechanical Accuracy
(Primary: Rating [Voltage System (kV) Primary & Secondary
30C (kVrms) (kVrms)
770584016 5:5 2.0 0.5 1.25 0.3 B-0.5 0.3 W,X,M,Y/1.2Z 25 150 50 2.5
770584026 10:5 2.0 1 2.5 0.3 B-0.5 0.3 W,X,M,Y/1.2Z 25 150 50 2.5
770584036 15:5 2.0 1.5 3.75 0.3 B-0.5 0.3 W,X,M,Y/1.2Z 25 150 50 2.5
770584046 20:5 2.0 2 5 0.3 B-0.5 0.3 W,X,M,Y/1.2Z 25 150 50 2.5
770584056 25:5 2.0 2.5 6.25 0.3 B-0.5 0.3 W,X,M,Y/1.2Z 25 150 50 2.5
770584066 30:5 2.0 3 7.5 0.3 B-0.5 0.3 W,X,M,Y/1.2Z 25 150 50 2.5
770584086 40:5 2.0 4 10 0.3 B-0.5 0.3 W,X,M,Y/1.2Z 25 150 50 2.5
770584106 50:5 2.0 5 12.5 0.3 B-0.5 0.3 W,X,M,Y/1.2Z 25 150 50 2.5
770584156 75:5 2.0 7.5 18.75 0.3 B-0.5 0.3 W,X,M,Y/1.2Z 25 150 50 2.5
770584206 100:5 2.0 10 25 0.3 B-0.5 0.3 W,X,M,Y/1.2Z 25 150 50 2.5
770585306 150:5 1.33 10 25 0.3 B-0.5 0.3 W,X,M,Y/1.2Z 25 150 50 2.5
770585406 200:5 1.0 10 25 0.3 B-0.5 0.3 W,X,M,Y/1.2Z 25 150 50 2.5
770581136 300:5 1.5 30 75 0.3 B-0.5 0.3 W,X,M,Y/1.2Z 25 125 50 2.5
770581146 400:5 1.5 40 100 0.3 B-0.5 0.3 W,X,M,Y/1.2Z 25 125 50 2.5
770581156 600:5 1.0 60 150 0.3 B-0.5 0.3 W,X,M,Y/1.2Z 25 125 50 2.5

770581106 100:5 2.0 10 25 0.15 B-0.5 0.3 W,X,M,Y/1.2Z 25 125 50 2.5
770581126 200:5 2.0 20 50 0.15 B-0.5 0.3 W,X,M,Y/1.2Z 25 125 50 2.5
770581156 600:5 1.0 48 120 0.15 B-0.5 0.3 W,X,M,Y/1.2Z 25 125 50 2.5

Rated
Secondary Voltage
(V) Factor 30s
(VA) (Un)
(Un)
120:1 14400/24940GY 120 750 1.1 1.25

KM-34 34.5 kV COMBINED TRANSFORMER
maintenance free.
OUTDOOR
Partial Discharge measurements exceed IEEE C57.13 2008 requirements
Resin Gray* 264 46 21
13 (330)
28.7 (729)
Lifting
holes
3/4 2 holes to conduit 1 hole 9/16
pipe 1 to ground 10 (254)
connection
H1 H2

/4
1
C1 C2
H0
MARKING
V1 V2
CONNEC- (Single
H1 H2
C1 C2 C3
H0
V1 V2


KM-34 34.5 kV COMBINED TRANSFORMER
Power-Frequency
Short- Short- IEEE
time time Metering
30C (kVrms) (kVrms)
770073017 5:5 3.0 0.5 1.4 0.3 B-1.8 0.3 W,X,M,Y/1.2Z 34.5 200 70 2.5
770073027 10:5 3.0 1 2.7 0.3 B-1.8 0.3 W,X,M,Y/1.2Z 34.5 200 70 2.5
770073037 15:5 3.0 1.5 4.1 0.3 B-1.8 0.3 W,X,M,Y/1.2Z 34.5 200 70 2.5
770073047 20:5 3.0 2 5.4 0.3 B-1.8 0.3 W,X,M,Y/1.2Z 34.5 200 70 2.5
770073057 25:5 3.0 2.5 6.8 0.3 B-1.8 0.3 W,X,M,Y/1.2Z 34.5 200 70 2.5
770073067 30:5 3.0 3 8.1 0.3 B-1.8 0.3 W,X,M,Y/1.2Z 34.5 200 70 2.5
770073077 40:5 3.0 4 10.8 0.3 B-1.8 0.3 W,X,M,Y/1.2Z 34.5 200 70 2.5
770073087 50:5 3.0 5 13.5 0.3 B-1.8 0.3 W,X,M,Y/1.2Z 34.5 200 70 2.5
770073097 75:5 3.0 7.5 20.3 0.3 B-1.8 0.3 W,X,M,Y/1.2Z 34.5 200 70 2.5
770073107 100:5 3.0 10 27 0.3 B-1.8 0.3 W,X,M,Y/1.2Z 34.5 200 70 2.5
770073117 150:5 3.0 15 40.5 0.3 B-1.8 0.3 W,X,M,Y/1.2Z 34.5 200 70 2.5
770073127 200:5 3.0 20 54 0.3 B-1.8 0.3 W,X,M,Y/1.2Z 34.5 200 70 2.5
770073137 300:5 3.0 30 81 0.3 B-1.8 0.3 W,X,M,Y/1.2Z 34.5 200 70 2.5
770073147 400:5 3.0 40 108 0.3 B-1.8 0.3 W,X,M,Y/1.2Z 34.5 200 70 2.5
770073157 600:5 2.0 60 162 0.3 B-1.8 0.3 W,X,M,Y/1.2Z 34.5 200 70 2.5
770071167 800:5 1.5 60 162 0.3 B-1.8 0.3 W,X,M,Y/1.2Z 34.5 200 70 2.5
770071177 1000:5 1.2 60 162 0.3 B-1.8 0.3 W,X,M,Y/1.2Z 34.5 200 70 2.5
770071187 1200:5 1.0 60 162 0.3 B-1.8 0.3 W,X,M,Y/1.2Z 34.5 200 70 2.5
770074047 10/20:5 2.0/1.5 2 5,4 0.3B-0.5/B-1.8 0.3 W,X,M,Y/1.2Z 34.5 200 70 2.5
770074087 25/50:5 2.0/1.5 5 13,5 0.3B-0.5/B-1.8 0.3 W,X,M,Y/1.2Z 34.5 200 70 2.5
770074127 100/200:5 2.0/1.5 20 54 0.3B-0.5/B-1.8 0.3 W,X,M,Y/1.2Z 34.5 200 70 2.5
770074157 300/600:5 2.0/1.5 60 162 0.3B-0.5/B-1.8 0.3 W,X,M,Y/1.2Z 34.5 200 70 2.5
770074167 400/800:5 2.0/1.5 60 162 0.3B-0.5/B-1.8 0.3 W,X,M,Y/1.2Z 34.5 200 70 2.5
770073167 400/800:5 3.0/1.5 60 162 0.3B-0.5/B-1.8 0.3 W,X,M,Y/1.2Z 34.5 200 70 2.5
770074177 500/1000:5 2.0/1.2 60 162 0.3B-0.5/B-1.8 0.3 W,X,M,Y/1.2Z 34.5 200 70 2.5
770074187 600/1200:5 2.0/1.0 60 162 0.3B-0.5/B-1.8 0.3 W,X,M,Y/1.2Z 34.5 200 70 2.5

770077127 200:5 3.0 20 50 0.15 B-0.5 0.3 W,X,M,Y/1.2Z 34.5 200 70 2.5
770078127 200:5 1.5 20 50 0.15 B-1.8 0.3 W,X,M,Y/1.2Z 34.5 200 70 2.5
770078177 1000:5 1.5 75 127.5 0.15 B-1.8 0.3 W,X,M,Y/1.2Z 34.5 200 70 2.5

Rated
Secondary Voltage
(V) Factor 30s
(VA) (Un)
(Un)
175:1 20125/34500GY 115 750 1.25 1.5

MK-34 34.5 kV METERING UNIT




OUTDOOR double isolation. The concentric distribution of the coils prevents magnetic
60 Hertz ux leakage, achieving greater accuracy and higher capacity to withstand

requirements.
Resin Gray* 857 46 21
40.4 (1026)
33 (838)
33 (838) 53.1 (1349)

L3 H1 H2
L2 H1 H2
L1 H1 H2
H1 H2 H1 H2 H1 H2
X1 X2 X1 X2 X1 X2
Type: NEMA-2 Type: TE-12 250 Material: Copper X1 X2 X1 X2 X1 X2
Material: Copper Range: 4TRE-250MCM
CONNEC- VT1 VT2 VT3 CT1 CT2 CT3
MARKING

/4
1 2 3 4 5 6 7 8 9 10
1


MK-34 34.5 kV METERING UNIT
Power-Frequency
Short- Short- IEEE
time time Metering
Code* Ratio Current Accuracy Voltage BIL
30C (kVrms) (kVrms)
770693017 5:5 3.0 0.5 1.4 0.3 B-1.8 0.3 W,X,M,Y/1.2Z 34.5 200 70 2.5
770693027 10:5 3.0 1 2.7 0.3 B-1.8 0.3 W,X,M,Y/1.2Z 34.5 200 70 2.5
770693037 15:5 3.0 1.5 4.1 0.3 B-1.8 0.3 W,X,M,Y/1.2Z 34.5 200 70 2.5
770693047 20:5 3.0 2 5.4 0.3 B-1.8 0.3 W,X,M,Y/1.2Z 34.5 200 70 2.5
770693057 25:5 3.0 2.5 6.8 0.3 B-1.8 0.3 W,X,M,Y/1.2Z 34.5 200 70 2.5
770693067 30:5 3.0 3 8.1 0.3 B-1.8 0.3 W,X,M,Y/1.2Z 34.5 200 70 2.5
770693077 40:5 3.0 4 10.8 0.3 B-1.8 0.3 W,X,M,Y/1.2Z 34.5 200 70 2.5
770693087 50:5 3.0 5 13.5 0.3 B-1.8 0.3 W,X,M,Y/1.2Z 34.5 200 70 2.5
770693097 75:5 3.0 7.5 20.3 0.3 B-1.8 0.3 W,X,M,Y/1.2Z 34.5 200 70 2.5
770693107 100:5 3.0 10 27 0.3 B-1.8 0.3 W,X,M,Y/1.2Z 34.5 200 70 2.5
770693117 150:5 3.0 15 40.5 0.3 B-1.8 0.3 W,X,M,Y/1.2Z 34.5 200 70 2.5
770693127 200:5 3.0 20 54 0.3 B-1.8 0.3 W,X,M,Y/1.2Z 34.5 200 70 2.5
770693137 300:5 3.0 30 81 0.3 B-1.8 0.3 W,X,M,Y/1.2Z 34.5 200 70 2.5
770693147 400:5 3.0 40 108 0.3 B-1.8 0.3 W,X,M,Y/1.2Z 34.5 200 70 2.5
770693157 600:5 2.0 60 162 0.3 B-1.8 0.3 W,X,M,Y/1.2Z 34.5 200 70 2.5
770693167 800:5 1.5 60 162 0.3 B-1.8 0.3 W,X,M,Y/1.2Z 34.5 200 70 2.5
770693177 1000:5 1.2 60 162 0.3 B-1.8 0.3 W,X,M,Y/1.2Z 34.5 200 70 2.5
770693187 1200:5 1.0 60 162 0.3 B-1.8 0.3 W,X,M,Y/1.2Z 34.5 200 70 2.5

770697127 200:5 3.0 20 54 0.15 B-0.5 0.3 W,X,M,Y/0.6Z 34.5 200 70 2.5
770698127 200:5 1.5 20 54 0.15 B-1.8 0.3 W,X,M,Y/0.6Z 34.5 200 70 2.5
770698177 1000:5 1.5 75 127.5 0.15 B-1.8 0.3 W,X,M,Y/0.6Z 34.5 200 70 2.5

Rated
Secondary Voltage
(V) Factor
(VA) (Un)
30s (Un)
175:1 20125/34500GY 115 750 1.25 1.5

ME-036 34.5 kV METERING UNIT




OUTDOOR The core is built with high permeability grain oriented silicon steel
60 Hertz laminations for low losses. The windings are copper wire with copper plate

requirements.
Y
X
Z
W

/4
1
CONNEC-
TIONS


ME-036 34.5 kV METERING UNIT
Characteristics
Weigth with
ME-036 CRF-36 URS-36 771010003 771010005 102.5 37 72.5 59 1060

ME-036 CRF-36 VRS-36 771010004 771010006 100.75 37 66.75 58.12 1087
Notes:

ARTECHE
Manufacturing ARTECHE
Facilities. USA Inc.
Arteche USA
18503 Pines Blvd. Suite 313.
Pembroke Pines, Florida 33029
Phone: 954 438 9499
Updates: ARTECHE_DS_trfMVGuide_EN
Fax: 954 438 9959 Version: D1
info@artecheusa.com
www.arteche.com/unitusa ARTECHE

Arteche Ds Trfmvguide en

Uploaded by

Copyright:

Available Formats

Arteche Ds Trfmvguide en

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Arteche Ds Trfmvguide en

Uploaded by

Copyright:

Available Formats

What are the two main types of instrument transformers discussed in the document?

What are the two main types of instrument transformers discussed in the document?

What are some common uses of instrument transformers?

What are some common uses of instrument transformers?

REFERENCE GUIDE

GENERAL TECHNICAL DATA

600 V INSTRUMENT TRANSFORMERS

5 kV 34.5 kV INDOOR INSTRUMENT TRANSFORMERS

5 kV 69 kV OUTDOOR INSTRUMENT TRANSFORMERS &

Instrument Transformers | Reference Guide www.arteche.com

There are two types of instrument transformer:

www.arteche.com Instrument Transformers | Reference Guide

100% rated current

will always produce a TCF between 0.997 and 1.003.

0.15 class- 100% 1.0015 0.15 accuracy class

-30 -20 -1 0 0 +1 0 +20 +30 .997

.994 Figure 3: VT Equivalent Parallelogram.

Instrument Transformers | Reference Guide www.arteche.com

Rated Current 10% 100% 150% (or Rating Factor)

Rated Current 5% 100% 150% (or Rating Factor)

Rated Current 5% 100% 150% (or Rating Factor)

Rated Current 5% 100% 150% (or Rating Factor)

Rated Current 1% 5% 100% 150% (or Rating Factor)

www.arteche.com Instrument Transformers | Reference Guide

Burden Resistance Inductance Impedance Volt- Power Secondary Burden

As per IEEE C57.13-2016, tables 10 and 13.

CROSS REFERENCE OF MOST COMMONLY USED TYPES

Current transformer Voltage transformer

ARTECHE GE ABB KUHLMAN ARTECHE GE ABB KUHLMAN

CID-17 JKM-5,5A KIR-11 CID-17 U/VCE-17 JVM-4,5 VIZ-11 U/VCD-17

Current transformer Voltage transformer

ARTECHE GE ABB KUHLMAN ARTECHE GE ABB KUHLMAN

CRB-17 JCK-5 KOR-11 BB-15-972 VRL-17 JVW-3 VOY-60 PTT-110-977

BB-15-971 & URJ-17 JVW-4,5 VOZ-75 PTT-110-9710G

BB-25-973 & VRN-17 JVW-4,5 VOZ-75 PTT-110-9710

BB-34-975 & VRN-24 JVW-6 VOY-15 PTT-150-9710

Instrument Transformers | Reference Guide www.arteche.com

www.arteche.com Instrument Transformers | Reference Guide

ARTECHE IRH series are dry type indoor/outdoor service current

See 4 x 5.25 (133)

Drawing number: 4287699

Primary Bar Type:

Drawing number: 4287759

ONE SECONDARY TERMINALS

Approximate dimensions in inches (mm).

10 www.arteche.com Instrument Transformers | Reference Guide

735221040 1.5" 200:5 3.0 2.0 0.3 B0.2 - 0.6 10 4 2.5

Instrument Transformers | Reference Guide www.arteche.com 11

ARTECHE IRH series are dry type indoor/outdoor service current

3.22 (81.79) 3.14 (79.76)

Drawing number: 4286166

ONE SECONDARY TERMINALS

Approximate dimensions in inches (mm).

12 www.arteche.com Instrument Transformers | Reference Guide

735261060 300:5 1.2 1.0 0.6B0.1/1.2B0.2 - 0.6 10 4 2.5

Additional ratings available upon request.

Instrument Transformers | Reference Guide www.arteche.com 13

ARTECHE IRH series are dry type indoor/outdoor service current

8. Lead length & type _, size - _(standard is #10 AWG)

9. Used in or above oil _ (Yes/No), or in dry surroundings - _ (Yes/No)