Sentry Multistandard

SENTRY MULTISTANDARD provides LOW POWER CONSUMPTION

maximum protection for critical data On-line Mode: up to 92% efficiency
processing networks and security can be achieved due to the use of
applications, thanks to its advanced IGBT technology, increasing to 98% in
design, selectable operating modes and one of the other operating modes
communications capabilities. Operating Economy Mode: uses Line Interactive
modes include: On-line, Economy, (VI) technology to power less critical
Smart-Active, Standby/Off and Voltage loads from the mains supply for certain
Stabilisation. Standard communications periods
features include a front panel LCD with Smart Active Mode: if the mains supply
128 potential messages, RS232 is out of range, the UPS will power the
interfaces, EPO input, communications load from the inverter as an On-line
interface slot and Watch&Save 3000 UPS. When the mains supply returns
management software. to within range again, the UPS will
monitor this for a certain period before
The SENTRY MULTISTANDARD series selecting Line Interactive operation.
includes 60-80 kVA three-phase models,
and uses on-line double conversion
technology (VFI). The load is powered
continuously by the inverter with a
filtered, stabilised and regulated sinewave
supply. The input and output filters
considerably increase the immunity of the
load to mains disturbances and surges,
even on bypass.

60
Fig. 1 Block diagram UPS in parallel up to 8 units

MAXIMUM RELIABILITY MAINTENANCE SIMPLICITY = LOW A large amount of maintenance

AND AVAILABILITY MTTR information is available from the front
Connect up to 8 units in parallel or Open the door and remove the mimic panel and LCD. In addition
N+1 redundancy, of even different protective panel (standards requirement) system operating parameters are
power ratings. and the power components - mounted software configurable via a local PC to
on a sliding tray - can be pulled out to allow new functions to be added or
HIGH LEVEL BATTERY RELIABILITY provide easy access to all the electrical adjustments made to operating
Automatic battery test and electronic components for specifications.
Recharge compensated for maintenance and repair work. This
temperature particular feature means that the MTTR
Automatic or manual rapid charge (Mean Time To Repair) is much lower
(boost) duration progammable than traditional UPS designs with less
easily reached assemblies, which has
longer times due to the compact size of
the products and difficult access to the
parts.

61
SENSITIVE SUPPLY COMPATIBLE advanced technology excellent capabilities
For power supply sources that are The active filter reduces harmonic Input distortion: (THDi) 4%
particularly sensitive to harmonics distortion of the phase and neutral Input power factor: >0.99
(generator sets or transformers of low currents. The Digital Signal Processor
power with respect to that of the UPS) it (DSP) and the current mode instantly Sentry Multistandard can also be
is often a good idea to take action to control and monitor the input current to supplied without the Active Filter
limit the harmonics injected back into the maintain a perfect sinewave with less for installations less sensitive to
supply by the UPS. than 4% harmonic distortion current harmonics.

maximum efficiency
SENTRY MULTISTANDARD series is also OTHER CHARACTERISTICS
Thanks to the active filter Sentry
available with built-in active filter using Suitable for powering capacitive loads
Multistandard systems have low input
high frequency Isolated Gate Bipolar such as blade servers, without any
distortion even at low loads and their
(IGBT) Technology with Digital Signal reduction of the active power, from 0.8
overall efficiency is not affected by
Processor (DSP) control. The Active leading to 0.8 lagging
generator frequency variations or line
Filter helps to reduce harmonics High level diagnostics: event log with
impedance
generated by the UPS into the supply 128 messages, states, measurements
which could disrupt the operation of reduction of neutral current and alarms - available from the built-in
downstream generators and The active filter reduces the input LCD in several languages
transformers whose rating is closely neutrals current by up to 3.5 times Reduced noise levels: high frequency
matched to that of UPS. their nominal rating to help avoid inverter bridge
oversizing input protections and Back feed protection standard: to
conductors avoid energy feeding back into the
mains supply (in compliance with CEI
maximum reliability 11-20; DK5600)
Sentry Multistandard systems are Power factor correction (input power
extremely reliable. Overall UPS factor, close to 1)
performance is unaffected should the By pass may be deactivated to allow
harmonic filter fail operation as a frequency converter (at
50 or 60 Hz)
Emergency operation: the UPS can be
set to operate only when the mains
fails (for emergency lighting)

UPS input current

with optional Active Filter

Sentry Multistandard with Active Filter

(internal view)

62
 Leading Cos (capacitive loads) Multistandard Output Power Lagging Cos (inductive loads)
Operating status, alarms, applied load,
cos 0,8 cos 0,9 100% kW cos 1 cos 0,9 cos 0,8
battery charging.
1,00

Active Power
0,75
100% kVA

0,50 Controls and settings menu.

0,25

-1 -0,8 -0,6 -0,4 -0,2 0 0,2 0,4 0,6 0,8 1

Reactive Power
Language selection menu.

ADVANCED COMMUNICATION APPLICATIONS

Compatible with TeleNetGuard for Local Area Networks (LAN)
remote maintenance Battery voltages, internal operating
Data Centers temperatures.
Advanced, multi-platform Servers
communication for all operating Industrial PLCs
systems and network environments: Cash registers OPTIONS
Watch&Save 3000 monitoring and Electromedical devices Input isolation transformer
shut-down software included, for Emergency devices (lights/alarms) Active filter
Windows 2008, Vista, 2003, XP; Mac Telecommunication devices LED remote status panel
OS X, Linux, Novell and most e-Business (Servers, Farms, LCD based remote control panel
popular Unix operating systems ISP/ASP/POP) Graphic Display remote control panel
The UPS is supplied with a Empty battery cabinet
communications cable for Plug and for prolonged runtime
Play PC connection Additional battery charger
Double RS232 serial ports Dual input mains
Network adapter slot for SNMP agent
Emergency Power Off (EPO) shutdown
input contact
Remote control mimic panel

63
Sentry Multistandard Technical data
Three-phase input
Three-phase output

Models ST60 ST80

Power (kVA) 60 80

Input ST60 ST80

Rated voltage 400 Vac three-phase + N
Voltage range 20%
Frequency range 45 65 Hz
Power factor > 0.99
Current harmonic distortion THDi 4%

By pass ST60 ST80

Rated voltage 400 Vac
Number of phases 3+N
Permitted voltage range 15% (selectable from 5% to 25%)
Rated frequency 50/60 Hz
Permitted frequency range 2% (selectable from 1% to 5%)

Batteries ST60 ST80

Type Lead, open vase acid and VRLA, AGM / GEL; NiCd
Recharge time 4-8 h

Output ST60 ST80

Rated power (kVA) 60 80
Active power
48 64
with load PF from 0,8 cap. to 0,8 ind. (kW)
Number of phases 3+N
Rated voltage 380 - 400 - 415 Vac selectable
Voltage regulation range 346 422 Vac
Crest factor (Ipeak/Irms) 3:1
Distortion with linear load 2%
Static stability 1%
Dynamic stability 5% in 10 ms
Frequency 50 / 60 Hz selectable
Overload 125% 150% of the rated current for 10/1

System ST60 ST80

Weight (kg) 180 192
Dimensions (wdh) (mm) 500x740x1400
Remote signaling Volt free contacts
Remote controls EPO and bypass
Communication Double RS232/C + remote contacts + communication interface slot
Operating temperature O C / +40 C
Relative humidity <95% non condensing
Colour Dark grey (RAL 7016)
Noise <56 dBA at 1 m <60 dBA at 1 m
Protection degree IP20
Efficiency Smart Mode > 98,5%
Compliance EN 62040-1 EMC EN 62040-2 EN 62040-3

64