SMPS

SMPS (Switched Mode Power Supply)
TABLE OF CONTENTS:
1. SMPS (Switched Mode Power Supply)

2. Type2: Forward Converters
3. Type3: Flyback Converters
4. Type4: Self- Oscillating
5. Advantages & Comparison
6. Application & Future
Written By:
Preeti Jain
D.C. to D.C. converters and D.C. to A.C. Converters belong to the category
of Switched Mode Power Supplies (SMPS). The various types of voltage regulators,
used in Linear Power Supplies (LPS), fall in the category of dissipative regulator, as
they have a voltage control element usually transistor or zener diode which dissipates
power equal to the voltage difference between an unregulated input voltage and a fixed
supply voltage multiplied by the current flowing through it. The switching regulator acts
as a continuously variable power converter and hence its efficiency is negligibly affected
by the voltage difference. Hence the switching regulator is also known as ‘non-
dissipative regulator’. In a SMPS, the active device that provides regulation is always
operated in cut-off or in saturation mode.
The input D.C. Supply is chopped at a higher frequency around 15 to 50 kHz using an active
device like the BJT, power MOSFET or SCR and the converter transformer. Here the size of the
ferrite core reduces inversely with the frequency. The lower limit is around 5 kHz for silent
operation and an upper limit of 50 kHz to limit the losses in the choke and in active switching
elements. The transformed wave form is rectified and filtered. A sample of the output voltage is
used as the feedback signal for the drive circuit for the switching transistor to achieve regulation.
Block Diagram of SMPS Working

The oscillator in above figure allows the control element to be switched ON and OFF.
The control element usually consists of a transistor switch, an inductor, and a diode. For
each switch ON, energy is pumped into the magnetic field associated with the inductor
which is a transformer winding in practice. This energy is then released to the load at
the desired voltage level.
By varying the duty cycle or frequency of switching, we can vary the stored energy in
each cycle and thus control the output voltage. Higher efficiency is obtained since only
the energy required is pumped to maintain the load current hence no power dissipation.
The major feature of SMPS is the elimination of physically massive power transformers
and other power line magnetic. The net result is smaller, lighter package and reduced
manufacturing cost, reducing primarily from the elimination of the 50 Hz components.
The basic concept of switching regulator in a simple form is shown in this figure below.
Types of SMPS:
· D.C. to D.C. Converter:
· Forward Converter:
· Flyback Converter:
· Self-Oscillating Flyback Converter:
D.C. to D.C. Converter:

The block diagram of D.C. to D.C. converter (SMPS) is shown here.
Here, the primary power received from AC main is rectified and filtered as high voltage
DC. It is then switched at a huge rate of speed approximately 15 kHz to 50 kHz and fed
to the primary side of the step-down transformer. The step-down transformer is only a
fraction of the size of a comparable 50 Hz unit thus reliving the size and weight
problems. The output at the secondary side of the transformer is rectified and filtered.
Then it is sent to the output of the power supply. A sample of this output is sent back to
the switch to control the output voltage.
SMPS rely on PWM to control the average value of the output voltage. The average
value of the repetitive pulse waveform depends on the area under the waveform. As
load increases, output voltage tends to fall. Most switching power supplies regulate their
output using the method called Pulse – Width Modulation (PWM). The power switch
which feeds the primary of the step-down transformer is driven by the PWM oscillator.
When the duty cycle is at 50%, then the maximum amount of energy will be passed
through the step-down transformer. As the duty cycle decreases the power transmitted
is less hence low power dissipation.
The Pulse Width signal given to the switch is inversely proportional to the output
voltage. The width or the ON time of the oscillator is controlled by the voltage feedback
from the secondary of the rectifier output and forms a closed loop regulator. Since
switching regulator is complex, modern IC packages like Motorola MC 3420/3520 or
Silicon General SG 1524 can be used instead of discrete components.

SMPS

Uploaded by

Copyright:

Available Formats

SMPS

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

SMPS

Uploaded by

Copyright:

Available Formats

What are the different types of SMPS discussed?

How does a SMPS work?

SMPS (Switched Mode Power Supply)

1. SMPS (Switched Mode Power Supply)

Block Diagram of SMPS Working

D.C. to D.C. Converter:

You might also like