Audio, Visual & Telephone System: Section
Audio, Visual & Telephone System: Section
Audio, Visual & Telephone System: Section
AV
A
B
SECTION
AUDIO, VISUAL & TELEPHONE SYSTEM C
E
CONTENTS
SERVICE INFORMATION ............................ 2 Wiring Diagram - AUDIO - ........................................ 5 F
Terminal and Reference Value for Audio Unit .......... 6
PRECAUTIONS ................................................... 2 Trouble Diagnosis ..................................................... 6
Precaution for Supplemental Restraint System Noise Inspection ....................................................... 7 G
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN- Power Supply Circuit Inspection ............................... 8
SIONER" ................................................................... 2 Sound Is Not Heard from Front Door Speaker ......... 8
Sound Is Not Heard from Rear Door Speaker .......... 9
PREPARATION ................................................... 3 H
Removal and Installation .........................................10
Commercial Service Tools ........................................ 3
AUDIO ANTENNA ............................................. 12
AUDIO ................................................................. 4 Location of Antenna .................................................12 I
Component Parts and Harness Connector Loca- Fixed Antenna Rod Replacement ............................12
tion ............................................................................ 4 Removal and Installation .........................................13
System Description ................................................... 4
J
AV
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SRS and SB section of
this Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SRS section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
B
Tool name Description
Power tool Loosening nuts, screws and bolts
C
PIIB1407E
AV
AWNIA2093ZZ
AV
AABWA0450GB
P
Terminal
Signal Condition
(Wire color) Reference value
Item input/
Ignition (Approx.)
+ – output Operation
switch
2 3
Audio signal front LH Output ON Receive audio signal
(LG) (BR)
ALMIA0456ZZ
4 5
Audio signal rear LH Output ON Receive audio signal
(R) (BR)
ALMIA0456ZZ
7
Ground ACC power supply Input ACC – Battery voltage
(P)
11 12
Audio signal front RH Output ON Receive audio signal
(GR) (B)
ALMIA0456ZZ
13 14
Audio signal rear RH Output ON Receive audio signal
(LG) (V)
ALMIA0456ZZ
19
Ground Battery power supply Input OFF – Battery voltage
(V)
• The majority of the audio malfunctions are the result of outside causes such as electromagnetic interference.
Check the symptoms below to diagnose the malfunction.
• The vehicle itself can be a source of noise if noise prevention parts or electrical equipment is malfunctioning.
Check if noise is caused and/or changed by engine speed, ignition switch turned to each position, and oper-
ation of each piece of electrical equipment, and then determine the cause.
1.CHECK FUSE
Check that the following fuses of the audio unit are not blown.
(+)
(-) OFF ACC ON
Connector Terminal
Battery Battery Battery
19 Ground
voltage voltage voltage
M17
Battery Battery
7 Ground 0V
voltage voltage
OK or NG ALMIA0457ZZ
OK >> GO TO 3.
NG >> • Check connector housings for disconnected or loose terminals.
• Repair harness or connector.
3.GROUND CIRCUIT CHECK
Inspect audio unit case ground.
OK or NG
OK >> Inspection End.
NG >> Repair audio unit case ground.
Sound Is Not Heard from Front Door Speaker INFOID:0000000008944816
1.HARNESS CHECK
1. Disconnect audio unit connector and front door speaker (LH or RH).
A B
Continuity
Connector Terminal Connector Terminal B
2 1
D3
3 2
M17 Yes C
11 1
D103
12 2
3. Check continuity between audio unit harness connector terminal D
and ground.
A E
— Continuity
Connector Terminal
2
F
3
M17 Ground No
11
12 G
ALMIA0458ZZ
OK or NG
OK >> GO TO 2.
NG >> • Check connector housings for disconnected or loose terminals. H
• Repair harness or connector.
2.FRONT SPEAKER SIGNAL CHECK I
1. Connect audio unit connector and front door speaker connector.
2. Turn ignition switch to ACC.
3. Push “POWER” switch.
4. Check the signal between audio unit connector terminals with J
CONSULT-III or oscilloscope.
(+) (-)
AV
Reference
Condition
Connector Terminal Terminal signal
2 3 L
Receive
M17 audio sig-
11 12 M
nal
ALMIA0460ZZ
N
OK or NG
OK >> Replace front speaker. Refer to AV-10, "Removal and
Installation". O
NG >> Replace audio unit. Refer to AV-10, "Removal and
Installation".
P
ALMIA0459ZZ
1.HARNESS CHECK
A B
Continuity
Connector Terminal Connector Terminal
4 1
D212
5 2
M17 Yes
13 1
D312
14 2
3. Check continuity between audio unit harness connector M17 (A)
and ground.
A
— Continuity
Connector Terminal
4
5
M17 Ground No
13 AWNIA2092ZZ
14
Are the continuity results as specified?
YES >> GO TO 2
NO >> • Check connector housings for disconnected or loose terminals.
• Repair harness or connector.
2.REAR DOOR SPEAKER SIGNAL CHECK
1. Connect audio unit connector and rear door speaker connector.
2. Turn ignition switch to ACC.
3. Push “POWER” switch.
4. Check the signal between audio unit harness connector M17
terminals with CONSULT-III or oscilloscope.
(+) (-)
Connector Condition Reference signal
Terminal Terminal
4 5
Receive
M17 audio sig-
13 14 nal
SKIA0177E
AUDIO UNIT
Removal
ALNIA1107ZZ
D
Installation
Installation is in the reverse order of removal.
E
FRONT DOOR SPEAKER
Removal
1. Remove the front door finisher. Refer to EI-25, "Removal and Installation". F
2. Remove the front door speaker screws (B), then pull out the
front door speaker (1).
G
3. Disconnect the harness connector from the front door speaker
(1) and remove.
4. Remove the front door speaker spacer screws (A), then remove
the front door speaker spacer (2) (if necessary). H
ALNIA1108ZZ
Installation J
Installation is in the reverse order of removal.
REAR DOOR SPEAKER
AV
Removal
1. Remove the rear door finisher (1). Refer to EI-25, "Removal and
Installation".
L
• Rear door speaker grille (A)
ALNIA1236ZZ
O
2. Remove the rear door speaker screws and clip, then pull out the rear door speaker.
3. Disconnect the harness connector from the rear door speaker and remove.
Installation P
Installation is in the reverse order of removal.
ALMIA0455ZZ
ALNIA1111ZZ
REMOVAL
1. Remove the antenna cover. C
2. Remove the cowl tops (LH/RH). Refer to EI-18, "Removal and Installation".
3. Remove the antenna assembly bolt.
4. Remove the fender protector (LH). Refer to EI-19, "Removal and Installation of Front Fender Protector". D
5. Detach the antenna feeder (1) from the clip (A) and detach the
rubber grommet (B).
E
G
ALNIA1118ZZ
AV
ALNIA1119ZZ
L
9. Disconnect the antenna feeder (audio unit) (1), located in the LH
foot well area and remove the antenna feeder (audio unit) (1).
M
O
ALNIA1120ZZ
10. Remove the antenna feeder (antenna assembly) pull out from the inner fender apron. P
11. Remove the antenna assembly.
INSTALLATION
Installation is in the reverse order of removal.