WW PDF
WW PDF
WW PDF
WW
A
B
SECTION
WIPER, WASHER & HORN C
E
CONTENTS
SERVICE INFORMATION ............................ 2 Removal and Installation .......................................... 8 F
WW
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SRS and SB section of
this Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SRS section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
WIPER OPERATION B
The wiper switch is controlled by a lever built into the combination switch.
There are two wiper switch positions:
• LO speed C
• HI speed
With the ignition switch in the ON or START position, power is supplied
• through 20A fuse (No. 26, located in the fuse block)
• to wiper motor terminal 4. D
Low and High Speed Wiper Operation
Ground is supplied to combination switch terminal 17 through body grounds M57 and M61.
With the combination switch (wiper) in the LO position, ground is supplied E
• to wiper motor terminal 2
• through combination switch terminal 14.
With power and ground supplied, the wiper motor operates at low speed.
With the combination switch (wiper) in the HI position, ground is supplied F
• to wiper motor terminal 3
• through combination switch terminal 16.
With power and ground supplied, the wiper motor operates at high speed. G
Auto Stop Operation
When the combination switch (wiper) is turned OFF, the wiper motor will continue to operate at low speed until
wiper blades reach windshield base (STOP position of the wiper motor position switch).
H
When wiper blades are not located at base of windshield (MOVE position of the wiper motor position switch)
with combination switch (wiper) OFF, ground is supplied
• to wiper motor terminal 2
• through combination switch terminal 14 I
• through combination switch terminal 13
• through wiper motor terminal 5
• through wiper motor terminal 6
J
• through body grounds M57 and M61.
WASHER OPERATION
With the ignition switch in the ON or START position, power is supplied WW
• through 20A fuse (No. 26, located in the fuse block)
• to washer motor terminal 1.
When the combination switch (wiper) is placed in the WASH position, ground is supplied
• to washer motor terminal 2 L
• from combination switch terminal 18
• through combination switch terminal 17
• through body grounds M57 and M61. M
With power and ground supplied, the washer motor operates.
AALWA0626GB
WIPER ARMS
Removal
F
FRONT WIPER ARM ADJUSTMENT
1. Operate the windshield washer and wiper motor one full cycle,
then turn "OFF" (Auto Stop).
G
2. Lift the blade up and then set it down onto glass surface to set
the blade center to clearance “L1”&“L2” immediately before
tightening nut.
H
3. Eject washer fluid. Turn on wiper switch to operate wiper motor
and then turn it “OFF”.
4. Ensure that wiper blades stop within clearance “L1”&“L2”.
I
Clearance “L1” : 25 mm (0.98 in) SEL543TA
ALKIA1508GB
Removal
1. Remove the cowl top. Refer to EI-18, "Removal and Installation".
2. Remove the wiper motor linkage cover and disconnect linkage at the wiper motor.
CAUTION:
Be careful not to break ball joint rubber boot.
ALKIA1509GB
3. Remove the bolts (A), disconnect the harness connector (B) and
remove the wiper motor (1).
ALKIA1524GB
4. Remove the wiper pivot nuts (A) and the wiper linkage (1).
ALKIA1510GB
Installation
Installation is the reverse order of removal.
NOTE:
Grease ball joint portion before installation.
A
• Adjust washer nozzle with suitable tool as shown.
D
SEL241P
E
Unit: mm (in)
H
SEL544T
WW
ALKIA1511GB
AAMWA0010GB
CIGARETTE LIGHTER
Removal
Revision: April 2013 WW-8 2013 D22 LCV
CIGARETTE LIGHTER
< SERVICE INFORMATION >
1. Remove cluster lid C. Refer to IP-10, "Removal and Installation".
2. Remove the cigarette lighter while pressing the tabs on the ring and disconnect the cigarette lighter con- A
nector.
Installation
Installation is in the reverse order of removal. B
WW
AALWA0628GB
HORN
Removal
Revision: April 2013 WW-10 2013 D22 LCV
HORN
< SERVICE INFORMATION >
1. Remove the bolt (A), disconnect the harness connector (B) and
remove the horn (1). A
ALKIA1522GB
D
Installation
Installation is in the reverse order of removal.
WW
ALKIA1523GB
Installation
Installation is in the reverse order of removal.
WASHER TANK B
Removal
1. Remove the headlamp assembly (LH). Refer to LT-11, "Removal and Installation".
C
2. Remove the bolts (A) and remove the washer tank (1).
: Front
3. Disconnect the harness connector and the washer hose. D
ALKIA1521GB
Installation G
Installation is in the reverse order of removal.
WW
Windshield washer fluid capacity 3.0 (3 1/8 US qt, 2 5/8 Imp qt)
Windshield washer fluid specification Refer to MA-9, "Fluids and Lubricants".