Dual-Channel Digital Isolators Adum1200/Adum1201: Data Sheet

Dual-Channel Digital Isolators
Data Sheet ADuM1200/ADuM1201

FEATURES current transfer ratios, nonlinear transfer functions, and temper-
Narrow body, RoHS-compliant, SOIC 8-lead package ature and lifetime effects are eliminated with the simple iCoupler
Low power operation digital interfaces and stable performance characteristics. The need
5 V operation for external drivers and other discrete components is eliminated
1.1 mA per channel maximum @ 0 Mbps to 2 Mbps with these iCoupler products. Furthermore, iCoupler devices
3.7 mA per channel maximum @ 10 Mbps consume one-tenth to one-sixth the power of optocouplers at
8.2 mA per channel maximum @ 25 Mbps comparable signal data rates.
3 V operation The ADuM120x isolators provide two independent isolation
0.8 mA per channel maximum @ 0 Mbps to 2 Mbps
channels in a variety of channel configurations and data rates
2.2 mA per channel maximum @ 10 Mbps
(see the Ordering Guide). Both parts operate with the supply
4.8 mA per channel maximum @ 25 Mbps
voltage on either side ranging from 2.7 V to 5.5 V, providing
Bidirectional communication
compatibility with lower voltage systems as well as enabling a
3 V/5 V level translation
voltage translation functionality across the isolation barrier.
High temperature operation: 125°C
In addition, the ADuM120x provide low pulse width distortion
High data rate: dc to 25 Mbps (NRZ)
(<3 ns for CR grade) and tight channel-to-channel matching
Precise timing characteristics
(<3 ns for CR grade). Unlike other optocoupler alternatives,
3 ns maximum pulse width distortion
the ADuM120x isolators have a patented refresh feature that
3 ns maximum channel-to-channel matching
ensures dc correctness in the absence of input logic transitions
High common-mode transient immunity: >25 kV/μs
and during power-up/power-down conditions.
Qualified for automotive applications
Safety and regulatory approvals The ADuM1200W and ADuM1201W are automotive grade
UL recognition versions qualified for 125°C operation. See the Automotive
2500 V rms for 1 minute per UL 1577 Products section for more information.
CSA Component Acceptance Notice #5A
VDE Certificate of Conformity FUNCTIONAL BLOCK DIAGRAMS
DIN V VDE V 0884-10 (VDE V 0884-10): 2006-12
VIORM = 560 V peak VDD1 1 8 VDD2
APPLICATIONS VIA 2 ENCODE DECODE 7 VOA
Size-critical multichannel isolation VIB 3 ENCODE DECODE 6 VOB

SPI interface/data converter isolation
04642-001
GND1 4 5 GND2
RS-232/RS-422/RS-485 transceiver isolation
Digital field bus isolation Figure 1. ADuM1200 Functional Block Diagram
Hybrid electric vehicles, battery monitor, and motor drive
GENERAL DESCRIPTION VDD1 1 8 VDD2
1
The ADuM120x are dual-channel digital isolators based on VOA 2 DECODE ENCODE 7 VIA
the Analog Devices, Inc., iCoupler® technology. Combining
VIB 3 ENCODE DECODE 6 VOB
high speed CMOS and monolithic transformer technologies,
04642-002
these isolation components provide outstanding performance GND1 4 5 GND2
characteristics superior to alternatives, such as optocouplers.

Figure 2. ADuM1201 Functional Block Diagram
By avoiding the use of LEDs and photodiodes, iCoupler devices
remove the design difficulties commonly associated with opto-
couplers. The typical optocoupler concerns regarding uncertain
1
Protected by U.S. Patents 5,952,849; 6,873,065; 6,903,578; and 7,075,329.
Rev. I
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Tel: 781.329.4700 www.analog.com
Trademarks and registered trademarks are the property of their respective owners. Fax: 781.461.3113 ©2004–2012 Analog Devices, Inc. All rights reserved.
ADuM1200/ADuM1201 Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1 DIN V VDE V 0884-10 (VDE V 0884-10): 2006-12
Insulation Characteristics ......................................................... 20
Applications....................................................................................... 1
Recommended Operating Conditions .................................... 20
General Description ......................................................................... 1
Absolute Maximum Ratings ......................................................... 21
Functional Block Diagrams............................................................. 1
ESD Caution................................................................................ 21
Revision History ............................................................................... 3
Pin Configurations and Function Descriptions ......................... 22
Specifications..................................................................................... 4
Typical Performance Characteristics ........................................... 23
Electrical Characteristics—5 V, 105°C Operation ................... 4
Applications Information .............................................................. 24
Electrical Characteristics—3 V, 105°C Operation ................... 6
PCB Layout ................................................................................. 24
Electrical Characteristics—Mixed 5 V/3 V or 3 V/5 V,
105°C Operation........................................................................... 8 Propagation Delay-Related Parameters................................... 24
Electrical Characteristics—5 V, 125°C Operation ................. 11 DC Correctness and Magnetic Field Immunity........................... 24
Electrical Characteristics—3 V, 125°C Operation ................. 13 Power Consumption .................................................................. 25
Electrical Characteristics—Mixed 5 V/3 V, 125°C Operation 15 Insulation Lifetime ..................................................................... 26
Electrical Characteristics—Mixed 3 V/5 V, 125°C Operation 17 Outline Dimensions ....................................................................... 27
Package Characteristics ............................................................. 19 Ordering Guide .......................................................................... 27
Regulatory Information............................................................. 19 Automotive Products ................................................................. 28
Insulation and Safety-Related Specifications.......................... 19
Rev. I | Page 2 of 28
REVISION HISTORY
3/12—Rev. H to Rev. I 8/07—Rev. C to Rev. D
Created Hyperlink for Safety and Regulatory Approvals Updated VDE Certification Throughout.......................................1
Entry in Features Section .................................................................1 Changes to Features, Note 1, Figure 1, and Figure 2 ....................1
Change to General Description Section.........................................1 Changes to Table 3 ............................................................................7
Change to PCB Layout Section .....................................................24 Changes to Regulatory Information Section...............................10
Moved Automotive Products Section...........................................28 Added Table 10 ................................................................................12
Added Insulation Lifetime Section ...............................................16
1/09—Rev. G to Rev. H Updated Outline Dimensions........................................................18
Changes to Table 5, Switching Specifications Parameter...........13 Changes to Ordering Guide...........................................................18
Changes to Table 6, Switching Specifications Parameter...........15
Changes to Table 7, Switching Specifications Parameter...........17 2/06—Rev. B to Rev. C
Updated Format ................................................................. Universal
9/08—Rev. F to Rev. G Added Note 1 .....................................................................................1
Changes to Table 9 ..........................................................................19 Changes to Absolute Maximum Ratings......................................12
Changes to Table 13 ........................................................................21 Changes to DC Correctness and Magnetic Field
Changes to Ordering Guide...........................................................27 Immunity Section............................................................................15
3/08—Rev. E to Rev. F 9/04—Rev. A to Rev. B

Changes to Features Section ............................................................1 Changes to Table 5 ..........................................................................10
Changes to Applications Section.....................................................1
Added Table 4 ..................................................................................11 6/04—Rev. 0 to Rev. A
Added Table 5 ..................................................................................13 Changes to Format............................................................. Universal
Added Table 6 ..................................................................................15 Changes to General Description .....................................................1
Added Table 7 ..................................................................................17 Changes to Electrical Characteristics—5 V Operation................3
Changes to Table 12 ........................................................................20 Changes to Electrical Characteristics—3 V Operation................5
Changes to Table 13 ........................................................................21 Changes to Electrical Characteristics—Mixed 5 V/3 V or
Added Automotive Products Section ...........................................26 3 V/5 V Operation ............................................................................7
Changes to Ordering Guide...........................................................27
4/04—Revision 0: Initial Version
11/07—Rev. D to Rev. E
Changes to Note 1 .............................................................................1
Added ADuM120xAR Change vs. Temperature Parameter .......3
SPECIFICATIONS
ELECTRICAL CHARACTERISTICS—5 V, 105°C OPERATION
All voltages are relative to their respective ground; 4.5 V ≤ VDD1 ≤ 5.5 V, 4.5 V ≤ VDD2 ≤ 5.5 V; all minimum/maximum specifications apply
over the entire recommended operating range, unless otherwise noted; all typical specifications are at TA = 25°C, VDD1 = VDD2 = 5 V; this
does not apply to the ADuM1200W and ADuM1201W automotive grade products.
Table 1.
Parameter Symbol Min Typ Max Unit Test Conditions
DC SPECIFICATIONS
Input Supply Current per Channel, Quiescent IDDI (Q) 0.50 0.60 mA
Output Supply Current per Channel, Quiescent IDDO (Q) 0.19 0.25 mA
ADuM1200 Total Supply Current, Two Channels 1
DC to 2 Mbps
VDD1 Supply Current IDD1 (Q) 1.1 1.4 mA DC to 1 MHz logic signal freq.
10 Mbps (BR and CR Grades Only)
VDD1 Supply Current IDD1 (10) 4.3 5.5 mA 5 MHz logic signal freq.
25 Mbps (CR Grade Only)
VDD1 Supply Current IDD1 (25) 10 13 mA 12.5 MHz logic signal freq.
VDD2 Supply Current IDD2 (25) 2.8 3.4 mA 12.5 MHz logic signal freq.
ADuM1201 Total Supply Current, Two Channels1
DC to 2 Mbps
For All Models
Input Currents IIA, IIB −10 +0.01 +10 μA 0 V ≤ VIA, VIB ≤ (VDD1 or VDD2)
Logic High Input Threshold VIH 0.7 (VDD1 or VDD2) V
Logic Low Input Threshold VIL 0.3 (VDD1 or VDD2) V
Logic High Output Voltages VOAH, VOBH (VDD1 or VDD2) − 0.1 5.0 V IOx = −20 μA, VIx = VIxH
(VDD1 or VDD2) − 0.5 4.8 V IOx = −4 mA, VIx = VIxH
Logic Low Output Voltages VOAL, VOBL 0.0 0.1 V IOx = 20 μA, VIx = VIxL
0.04 0.1 V IOx = 400 μA, VIx = VIxL
0.2 0.4 V IOx = 4 mA, VIx = VIxL
SWITCHING SPECIFICATIONS
ADuM120xAR CL = 15 pF, CMOS signal levels
Minimum Pulse Width 2 PW 1000 ns
Maximum Data Rate 3 1 Mbps
Propagation Delay 4 tPHL, tPLH 50 150 ns
Pulse Width Distortion, |tPLH − tPHL|4 PWD 40 ns
Change vs. Temperature 11 ps/°C
Propagation Delay Skew 5 tPSK 100 ns
Channel-to-Channel Matching 6 tPSKCD/tPSKOD 50 ns
Output Rise/Fall Time (10% to 90%) tR/tF 10 ns
ADuM120xBR
Minimum Pulse Width2 PW 100 ns
3 10 Mbps
Maximum Data Rate
Propagation Delay4 tPHL, tPLH 20 50 ns
Propagation Delay Skew5 tPSK 15 ns
Channel-to-Channel Matching 3
Codirectional Channels6 tPSKCD ns
6 tPSKOD 15 ns
Opposing Directional Channels
Output Rise/Fall Time (10% to 90%) tR/tF 2.5 ns
ADuM120xCR
Minimum Pulse Width2 PW 20 40 ns
Maximum Data Rate3 25 50 Mbps
Channel-to-Channel Matching 3 ns
Codirectional Channels6 tPSKCD
Opposing Directional Channels6 tPSKOD 15 ns
For All Models
Common-Mode Transient Immunity
Logic High Output 7 |CMH| 25 35 kV/μs VIx = VDD1 or VDD2, VCM =
1000 V, transient
magnitude = 800 V
Logic Low Output7 |CML| 25 35 kV/μs VIx = 0 V, VCM = 1000 V,
transient magnitude = 800 V
Refresh Rate fr 1.2 Mbps
Dynamic Supply Current per Channel 8
Input IDDI (D) 0.19 mA/
Mbps
Output IDDO (D) 0.05 mA/
Mbps
1
The supply current values are for both channels combined when running at identical data rates. Output supply current values are specified with no output load
present. The supply current associated with an individual channel operating at a given data rate can be calculated as described in the Power Consumption section. See
Figure 6 through Figure 8 for information on per-channel supply current as a function of data rate for unloaded and loaded conditions. See Figure 9 through Figure 11
for total VDD1 and VDD2 supply currents as a function of data rate for ADuM1200 and ADuM1201 channel configurations.
2
The minimum pulse width is the shortest pulse width at which the specified pulse width distortion is guaranteed.
3
The maximum data rate is the fastest data rate at which the specified pulse width distortion is guaranteed.
4
tPHL propagation delay is measured from the 50% level of the falling edge of the VIx signal to the 50% level of the falling edge of the VOx signal. tPLH propagation delay is
measured from the 50% level of the rising edge of the VIx signal to the 50% level of the rising edge of the VOx signal.
5
tPSK is the magnitude of the worst-case difference in tPHL and/or tPLH that is measured between units at the same operating temperature, supply voltages, and output
load within the recommended operating conditions.
6
Codirectional channel-to-channel matching is the absolute value of the difference in propagation delays between any two channels with inputs on the same side of
the isolation barrier. Opposing directional channel-to-channel matching is the absolute value of the difference in propagation delays between any two channels with
inputs on opposing sides of the isolation barrier.
7
CMH is the maximum common-mode voltage slew rate that can be sustained while maintaining VO > 0.8 VDD2. CML is the maximum common-mode voltage slew rate
that can be sustained while maintaining VO < 0.8 V. The common-mode voltage slew rates apply to both rising and falling common-mode voltage edges. The transient
magnitude is the range over which the common mode is slewed.
8
Dynamic supply current is the incremental amount of supply current required for a 1 Mbps increase in the signal data rate. See Figure 6 through Figure 8 for
information on per-channel supply current as a function of data rate for unloaded and loaded conditions. See the Power Consumption section for guidance on
calculating per-channel supply current for a given data rate.
over the entire recommended operating range, unless otherwise noted; all typical specifications are at TA = 25°C, VDD1 = VDD2 = 3.0 V; this
does not apply to ADuM1200W and ADuM1201W automotive grade products.
Table 2.
DC SPECIFICATIONS
Input Supply Current per Channel, Quiescent IDDI (Q) 0.26 0.35 mA
DC to 2 Mbps
DC to 2 Mbps
For All Models
Logic Low Input Threshold VIL 0.3 (VDD1 or VDD2)
0.04 0.1 V IOx = 400 μA, VIx = VIxL
Maximum Data Rate3 1 Mbps
Channel-to-Channel Matching6 tPSKCD/tPSKOD 50 ns
ADuM120xBR CL = 15 pF, CMOS signal levels
Channel-to-Channel Matching
Codirectional Channels6 tPSKCD 3 ns
ADuM120xCR
3 25 50 Mbps
Maximum Data Rate
4 tPHL, tPLH 20 55 ns
Propagation Delay
For All Models
Logic High Output 7 |CMH| 25 35 kV/μs VIx = VDD1 or VDD2, VCM = 1000 V,
Dynamic Supply Current per Channel 8
Mbps
Mbps
1
2
3
4
5
6
7
8
ELECTRICAL CHARACTERISTICS—MIXED 5 V/3 V OR 3 V/5 V, 105°C OPERATION
All voltages are relative to their respective ground; 5 V/3 V operation: 4.5 V ≤ VDD1 ≤ 5.5 V, 2.7 V ≤ VDD2 ≤ 3.6 V. 3 V/5 V operation:
2.7 V ≤ VDD1 ≤ 3.6 V, 4.5 V ≤ VDD2 ≤ 5.5 V; all minimum/maximum specifications apply over the entire recommended operating range,
unless otherwise noted; all typical specifications are at TA = 25°C; VDD1 = 3.0 V, VDD2 = 5.0 V; or VDD1 = 5.0 V, VDD2 = 3.0 V; this does not
apply to ADuM1200W and ADuM1201W automotive grade products.
Table 3.
DC SPECIFICATIONS
Input Supply Current per Channel, IDDI (Q)
Quiescent
5 V/3 V Operation 0.50 0.6 mA
Output Supply Current per Channel, IDDO (Q)
Quiescent
ADuM1200 Total Supply Current,
Two Channels1
DC to 2 Mbps
VDD1 Supply Current IDD1 (Q)
5 V/3 V Operation 1.1 1.4 mA DC to 1 MHz logic signal freq.
VDD1 Supply Current IDD1 (10)
5 V/3 V Operation 4.3 5.5 mA 5 MHz logic signal freq.
5 V/3 V Operation 10 13 mA 12.5 MHz logic signal freq.
3 V/5 V Operation 5.2 7.7 mA 12.5 MHz logic signal freq.
ADuM1201 Total Supply Current,
Two Channels1
DC to 2 Mbps
For All Models
Logic High Output Voltages VOAH, VOBH (VDD1 or VDD2) − 0.1 VDD1 or VDD2 V IOx = −20 μA, VIx = VIxH
(VDD1 or VDD2) − 0.5 (VDD1 or VDD2) − 0.2 V IOx = −4 mA, VIx = VIxH
0.04 0.1 V IOx = 400 μA, VIx = VIxL
ADuM120xBR CL = 15 pF, CMOS signal levels
Propagation Delay
4 PWD 3 ns
Pulse Width Distortion, |tPLH − tPHL|
Output Rise/Fall Time (10% to 90%) tR/tF
5 V/3 V Operation 3.0 ns
ADuM120xCR CL = 15 pF, CMOS signal levels
Output Rise/Fall Time (10% to 90%) tR/tF
For All Models
Logic High Output 7 |CMH| 25 35 kV/μs VIx = VDD1 or VDD2, VCM = 1000 V,
Refresh Rate fr
5 V/3 V Operation 1.2 Mbps
3 V/5 V Operation 1.1 Mbps
Input Dynamic Supply Current IDDI (D)
per Channel 8
5 V/3 V Operation 0.19 mA/
Mbps
Mbps
Output Dynamic Supply Current per IDDO (D)
Channel8
Mbps
Mbps
1
2
3
4
5
6
7
8
over the entire recommended operating range, unless otherwise noted; all typical specifications are at TA = 25°C, VDD1 = VDD2 = 5 V; this
applies to ADuM1200W and ADuM1201W automotive grade products.
Table 4.
DC SPECIFICATIONS
Input Supply Current per Channel, IDDI (Q) 0.50 0.60 mA
Quiescent
Output Supply Current per Channel, IDDO (Q) 0.19 0.25 mA
Quiescent
ADVM1200W, Total Supply Current,
Two Channels 1
DC to 2 Mbps
10 Mbps (TRZ and URZ Grades Only)
25 Mbps (URZ Grade Only)
Two Channels1
DC to 2 Mbps
For All Models
Input Currents IIA, IIB −10 +0.01 +10 μA 0 7≤ VIA, VIB ≤ (VDD1 or VDD2)
0.04 0.1 V IOx = 400 μA, VIx = VIxL
ADuM120xWSRZ CL = 15 pF, CMOS signal levels
ADuM120xWTRZ CL = 15 pF, CMOS signal levels
ADuM120xWURZ CL = 15 pF, CMOS signal levels
Propagation Delay
For All Models
Logic High Output7 |CMH| 25 35 kV/μs VIx = VDD1, VDD2, VCM = 1000 V,
Dynamic Supply Current per Channel8
Mbps
Mbps
1
for total IDD1 and IDD2 supply currents as a function of data rate for ADuM1200W and ADuM1201W channel configurations.
2
3
4
5
6
7
8
All voltages are relative to their respective ground; 3.0 V ≤ VDD1 ≤ 3.6 V, 3.0 V ≤ VDD2 ≤ 3.6 V. All minimum/maximum specifications apply
over the entire recommended operating range, unless otherwise noted; all typical specifications are at TA = 25°C, VDD1 = VDD2 = 3.0 V;
this applies to ADuM1200W and ADuM1201W automotive grade products.
Table 5.
DC SPECIFICATIONS
Quiescent
Two Channels 1
DC to 2 Mbps
Two Channels1
DC to 2 Mbps
For All Models
Input Currents IIA, IIB −10 +0.01 +10 μA 0 7≤ VIA, VIB ≤ (VDD1 or VDD2)
Logic Low Input Threshold VIL 0.3 (VDD1 or VDD2)
0.04 0.1 V IOx = 400 μA, VIx = VIxL
Propagation Delay
4 PWD 3 ns
Pulse Width Distortion, |tPLH − tPHL|
ADuM120xWCR CL = 15 pF, CMOS signal levels
6 tPSKOD 16 ns
For All Models
Mbps
Mbps
1
2
The minimum pulse width is the shortest pulse width at which the specified pulsewidth distortion is guaranteed.
3
The maximum data rate is the fastest data rate at which the specified pulsewidth distortion is guaranteed.
4
5
6
7
8
ELECTRICAL CHARACTERISTICS—MIXED 5 V/3 V, 125°C OPERATION
All voltages are relative to their respective ground; 5 V/3 V operation: 4.5 V ≤ VDD1 ≤ 5.5 V, 3.0 V ≤ VDD2 ≤ 3.6 V. 3 V/5 V operation; all
minimum/maximum specifications apply over the entire recommended operating range, unless otherwise noted; all typical specifications
are at TA = 25°C; VDD1 = 5.0 V, VDD2 = 3.0 V; this applies to ADuM1200W and ADuM1201W automotive grade products.
Table 6.
DC SPECIFICATIONS
Quiescent
Quiescent
ADuM1200W, Total Supply Current,
Two Channels1
DC to 2 Mbps
Two Channels1
DC to 2 Mbps
For All Models
0.04 0.1 V IOx = 400 μA, VIx = VIxL
Channel-to-Channel Matching6 tPSKCD/ tPSKOD 50 ns
Propagation Delay
6 tPSKOD 22 ns
For All Models
Logic Low Output7 |CML| 25 35 kV/μs VIx = VDD1, VDD2, VCM = 1000 V,
Mbps
Mbps
1
2
3
4
5
6
7
8
ELECTRICAL CHARACTERISTICS—MIXED 3 V/5 V, 125°C OPERATION
over the entire recommended operating range, unless otherwise noted; all typical specifications are at TA = 25°C; VDD1 = 3.0 V, VDD2 = 5.0 V;
this applies to ADuM1200W and ADuM1201W automotive grade products.
Table 7.
DC SPECIFICATIONS
Quiescent
Quiescent
Two Channels1
DC to 2 Mbps
Two Channels1
DC to 2 Mbps
For All Models
0.04 0.1 V IOx = 400 μA, VIx = VIxL
Channel-to-Channel Matching6 tPSKCD/ 50 ns
tPSKOD
Propagation Delay
6 tPSKOD 15 ns
For All Models
Input Dynamic Supply Current IDDI (D) 0.10 mA/
per Channel8 Mbps
Output Dynamic Supply Current IDDO (D) 0.05 mA/
per Channel8 Mbps
1
2
3
4
5
6
7
8
PACKAGE CHARACTERISTICS
Table 8.
Resistance (Input-to-Output)1 RI-O 1012 Ω
Capacitance (Input-to-Output)1 CI-O 1.0 pF f = 1 MHz
Input Capacitance CI 4.0 pF
IC Junction-to-Case Thermal Resistance, Side 1 θJCI 46 °C/W Thermocouple located at
center of package underside
IC Junction-to-Case Thermal Resistance, Side 2 θJCO 41 °C/W
1
The device is considered a 2-terminal device; Pin 1, Pin, 2, Pin 3, and Pin 4 are shorted together, and Pin 5, Pin 6, Pin 7, and Pin 8 are shorted together.
REGULATORY INFORMATION
The ADuM1200/ADuM1201 and ADuM1200W/ADuM1201W are approved by the organizations listed in Table 9; refer to Table 14 and
the Insulation Lifetime section for details regarding recommended maximum working voltages for specific cross-isolation waveforms and
insulation levels.
Table 9.
UL CSA VDE
Recognized Under 1577 Component Approved under CSA Component Acceptance Certified according to DIN V VDE V
Recognition Program1 Notice #5A; approval pending for ADuM1200W/ 0884-10 (VDE V 0884-10): 2006-122
ADuM1201W automotive 125°C temperature grade
Single/Basic 2500 V rms Isolation Voltage Basic insulation per CSA 60950-1-03 and Reinforced insulation, 560 V peak
IEC 60950-1, 400 V rms (566 peak) maximum
working voltage
Functional insulation per CSA 60950-1-03 and
IEC 60950-1, 800 V rms (1131 V peak) maximum
working voltage
File E214100 File 205078 File 2471900-4880-0001
1
In accordance with UL 1577, each ADuM120x is proof tested by applying an insulation test voltage ≥ 3000 V rms for 1 second (current leakage detection limit = 5 μA).
2
In accordance with DIN V VDE V 0884-10, each ADuM120x is proof tested by applying an insulation test voltage ≥ 1050 V peak for 1 sec (partial discharge detection
limit = 5 pC). The * marking branded on the component designates DIN V VDE V 0884-10 approval.
INSULATION AND SAFETY-RELATED SPECIFICATIONS

Table 10.
Parameter Symbol Value Unit Conditions
Rated Dielectric Insulation Voltage 2500 V rms 1 minute duration
Minimum External Air Gap (Clearance) L(I01) 4.90 min mm Measured from input terminals to output terminals,
shortest distance through air
Minimum External Tracking (Creepage) L(I02) 4.01 min mm Measured from input terminals to output terminals,
shortest distance path along body
Minimum Internal Gap (Internal Clearance) 0.017 min mm Insulation distance through insulation
Tracking Resistance (Comparative Tracking Index) CTI >175 V DIN IEC 112/VDE 0303 Part 1
Isolation Group IIIa Material Group (DIN VDE 0110, 1/89, Table 1)
DIN V VDE V 0884-10 (VDE V 0884-10): 2006-12 INSULATION CHARACTERISTICS
This isolator is suitable for reinforced isolation only within the safety limit data. Maintenance of the safety data is ensured by protective
circuits. Note that the asterisk (*) marking on the package denotes DIN V VDE V 0884-10 approval for a 560 V peak working voltage.
Table 11.
Description Conditions Symbol Characteristic Unit
Installation Classification per DIN VDE 0110
For Rated Mains Voltage ≤ 150 V rms I to IV
For Rated Mains Voltage ≤ 300 V rms I to III
For Rated Mains Voltage ≤ 400 V rms I to II
Climatic Classification 40/105/21
Pollution Degree per DIN VDE 0110, Table 1 2
Maximum Working Insulation Voltage VIORM 560 V peak
Input-to-Output Test Voltage, Method B1 VIORM × 1.875 = VPR, 100% production test, VPR 1050 V peak
tm = 1 second, partial discharge < 5 pC
Input-to-Output Test Voltage, Method A VIORM × 1.6 = VPR, tm = 60 seconds, VPR
partial discharge < 5 pC
After Environmental Tests Subgroup 1 896 V peak
After Input and/or Safety Test Subgroup 2 VIORM × 1.2 = VPR, tm = 60 seconds, 672 V peak
and Subgroup 3 partial discharge < 5 pC
Highest Allowable Overvoltage Transient overvoltage, tTR = 10 seconds VTR 4000 V peak
Safety-Limiting Values Maximum value allowed in the event of a failure
(see Figure 3)
Case Temperature TS 150 °C
Side 1 Current IS1 160 mA
Side 2 Current IS2 170 mA
Insulation Resistance at TS VIO = 500 V RS >109 Ω
RECOMMENDED OPERATING CONDITIONS

200
180 Table 12.

Parameter Rating
SAFETY-LIMITING CURRENT (mA)
160
Operating Temperature (TA) 1 −40°C to +105°C
140
SIDE #1 SIDE #2 Operating Temperature (TA) 2 −40°C to +125°C
120
Supply Voltages (VDD1, VDD2)1, 3 2.7 V to 5.5 V
100 Supply Voltages (VDD1, VDD2)2, 3 3.0 V to 5.5 V
80 Input Signal Rise and Fall Times 1.0 ms
60 1
Does not apply to ADuM1200W and ADuM1201W automotive grade
40 products.
2
Applies to ADuM1200W and ADuM1201W automotive grade products.
20 3
All voltages are relative to their respective ground. See the DC Correctness
and Magnetic Field Immunity section for information on immunity to external
0
04642-003
0 50 100 150 200 magnetic fields.

CASE TEMPERATURE (°C)
Figure 3. Thermal Derating Curve, Dependence of Safety-Limiting Values

on Case Temperature per DIN V VDE V 0884-10
ABSOLUTE MAXIMUM RATINGS

Ambient temperature = 25°C, unless otherwise noted. Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
Table 13. rating only; functional operation of the device at these or any
Parameter Rating other conditions above those indicated in the operational
Storage Temperature (TST) −55°C to +150°C section of this specification is not implied. Exposure to absolute
Ambient Operating Temperature (TA) 1 −40°C to +105°C maximum rating conditions for extended periods may affect
Ambient Operating Temperature (TA) 2 −40°C to +125°C device reliability.
Supply Voltages (VDD1, VDD2) 3 −0.5 V to +7.0 V
Input Voltages (VIA, VIB)3, 4 −0.5 V to VDDI + 0.5 V
ESD CAUTION
Output Voltages (VOA, VOB)3, 4 −0.5 V to VDDO + 0.5 V
Average Output Current per Pin (IO) 5 −11 mA to +11 mA
Common-Mode Transients (CML, CMH)6 −100 kV/μs to +100 kV/μs
1
Does not apply to ADuM1200W and ADuM1200W automotive grade
products.
2
Applies to ADuM1200W and ADuM1201W automotive grade products.
3
All voltages are relative to their respective ground.
4
VDDI and VDDO refer to the supply voltages on the input and output sides of a
given channel, respectively.
5
See Figure 3 for maximum rated current values for various temperatures.
6
Refers to common-mode transients across the insulation barrier.
Common-mode transients exceeding the absolute maximum ratings
can cause latch-up or permanent damage.
Table 14. Maximum Continuous Working Voltage1

Parameter Max Unit Constraint
AC Voltage, Bipolar Waveform 565 V peak 50-year minimum lifetime
AC Voltage, Unipolar Waveform
Functional Insulation 1131 V peak Maximum approved working voltage per IEC 60950-1
Basic Insulation 560 V peak Maximum approved working voltage per IEC 60950-1 and VDE V 0884-10
DC Voltage
Functional Insulation 1131 V peak Maximum approved working voltage per IEC 60950-1
Basic Insulation 560 V peak Maximum approved working voltage per IEC 60950-1 and VDE V 0884-10
1
Refers to continuous voltage magnitude imposed across the isolation barrier. See the Insulation Lifetime section for more details.
PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS

VDD1 1 8 VDD2 VDD1 1 8 VDD2
VIA 2 ADuM1200 7 VOA VOA 2 ADuM1201 7 VIA
TOP VIEW TOP VIEW
VIB 3 6 VOB
04642-005
(Not to Scale) VIB 3 6 VOB
(Not to Scale)
04642-004
GND1 4 5 GND2 GND1 4 5 GND2
Figure 4. ADuM1200 Pin Configuration Figure 5. ADuM1201 Pin Configuration
Table 15. ADuM1200 Pin Function Descriptions Table 16. ADuM1201 Pin Function Descriptions
Pin Pin
No. Mnemonic Description No. Mnemonic Description
1 VDD1 Supply Voltage for Isolator Side 1. 1 VDD1 Supply Voltage for Isolator Side 1.
2 VIA Logic Input A. 2 VOA Logic Output A.
3 VIB Logic Input B. 3 VIB Logic Input B.
4 GND1 Ground 1. Ground Reference for Isolator Side 1. 4 GND1 Ground 1. Ground Reference for Isolator Side 1.
5 GND2 Ground 2. Ground Reference for Isolator Side 2. 5 GND2 Ground 2. Ground Reference for Isolator Side 2.
6 VOB Logic Output B. 6 VOB Logic Output B.
7 VOA Logic Output A. 7 VIA Logic Input A.
8 VDD2 Supply Voltage for Isolator Side 2. 8 VDD2 Supply Voltage for Isolator Side 2.
Table 17. ADuM1200 Truth Table (Positive Logic)

VIA Input VIB Input VDD1 State VDD2 State VOA Output VOB Output Notes
H H Powered Powered H H
L L Powered Powered L L
H L Powered Powered H L
L H Powered Powered L H
X X Unpowered Powered H H Outputs return to the input state within
1 μs of VDDI power restoration.
X X Powered Unpowered Indeterminate Indeterminate Outputs return to the input state within
1 μs of VDDO power restoration.
Table 18. ADuM1201 Truth Table (Positive Logic)

VIA Input VIB Input VDD1 State VDD2 State VOA Output VOB Output Notes
H H Powered Powered H H
L L Powered Powered L L
H L Powered Powered H L
L H Powered Powered L H
X X Unpowered Powered Indeterminate H Outputs return to the input state within
1 μs of VDDI power restoration.
X X Powered Unpowered H Indeterminate Outputs return to the input state within
1 μs of VDDO power restoration.
TYPICAL PERFORMANCE CHARACTERISTICS

10 20
8
15
CURRENT/CHANNEL (mA)
CURRENT (mA)
6
10
4 5V
5V
3V 5
2
3V
0 0
04642-006
04642-009
0 10 20 30 0 10 20 30
DATA RATE (Mbps) DATA RATE (Mbps)
Figure 6. Typical Input Supply Current per Channel vs. Data Rate Figure 9. Typical ADuM1200 VDD1 Supply Current vs. Data Rate
for 5 V and 3 V Operation for 5 V and 3 V Operation
4 4
3 3
CURRENT (mA)
2 2
5V 5V
3V
1 1
3V
0 0
04642-010
04642-007
0 10 20 30 0 10 20 30
Figure 7. Typical Output Supply Current per Channel vs. Data Rate Figure 10. Typical ADuM1200 VDD2 Supply Current vs. Data Rate
for 5 V and 3 V Operation (No Output Load) for 5 V and 3 V Operation
4 10
8
3
CURRENT (mA)
6
5V
2 5V
3V 3V
1
2
0 0
04642-011
04642-008
0 10 20 30 0 10 20 30
Figure 8. Typical Output Supply Current per Channel vs. Data Rate Figure 11. Typical ADuM1201 VDD1 or VDD2 Supply Current vs. Data Rate
for 5 V and 3 V Operation (15 pF Output Load) for 5 V and 3 V Operation
APPLICATIONS INFORMATION
PCB LAYOUT The ADuM120x are extremely immune to external magnetic
The ADuM120x digital isolators require no external interface fields. The limitation on the magnetic field immunity of the
circuitry for the logic interfaces. Power supply bypassing is ADuM120x is set by the condition in which induced voltage in
strongly recommended at the input and output supply pins. the receiving coil of the transformer is sufficiently large enough
The capacitor value should be between 0.01 μF and 0.1 μF. to either falsely set or reset the decoder. The following analysis
The total lead length between both ends of the capacitor and defines the conditions under which this can occur. The 3 V
the input power supply pin should not exceed 20 mm. operating condition of the ADuM120x is examined because
it represents the most susceptible mode of operation.
See the AN-1109 Application Note for board layout guidelines.
The pulses at the transformer output have an amplitude greater
PROPAGATION DELAY-RELATED PARAMETERS than 1.0 V. The decoder has a sensing threshold at about 0.5 V,
Propagation delay is a parameter that describes the time it takes therefore establishing a 0.5 V margin in which induced voltages
a logic signal to propagate through a component. The propagation can be tolerated. The voltage induced across the receiving coil is
delay to a logic low output can differ from the propagation delay given by
to a logic high output. V = (−dβ/dt)Σ∏rn2; n = 1, 2, … , N
INPUT (VIx) 50%

where:
β is the magnetic flux density (gauss).
tPLH tPHL N is the number of turns in the receiving coil.
04642-012
OUTPUT (VOx) 50% rn is the radius of the nth turn in the receiving coil (cm).
Figure 12. Propagation Delay Parameters Given the geometry of the receiving coil in the ADuM120x and
an imposed requirement that the induced voltage be 50% at
Pulse width distortion is the maximum difference between most of the 0.5 V margin at the decoder, a maximum allowable
these two propagation delay values and is an indication of magnetic field is calculated, as shown in Figure 13.
how accurately the timing of the input signal is preserved.
100
Channel-to-channel matching refers to the maximum amount

MAXIMUM ALLOWABLE MAGNETIC FLUX
that the propagation delay differs between channels within a 10

single ADuM120x component.
DENSITY (kgauss)
Propagation delay skew refers to the maximum amount that 1
the propagation delay differs between multiple ADuM120x

components operating under the same conditions. 0.1
DC CORRECTNESS AND MAGNETIC FIELD IMMUNITY

Positive and negative logic transitions at the isolator input send 0.01
narrow (~1 ns) pulses to the decoder via the transformer. The
decoder is bistable and is therefore either set or reset by the pulses, 0.001
04642-013
1k 10k 100k 1M 10M 100M

indicating input logic transitions. In the absence of logic transi- MAGNETIC FIELD FREQUENCY (Hz)
tions of more than ~1 μs at the input, a periodic set of refresh Figure 13. Maximum Allowable External Magnetic Flux Density
pulses indicative of the correct input state is sent to ensure dc
correctness at the output. If the decoder receives no internal
pulses for more than about 5 μs, the input side is assumed to be
unpowered or nonfunctional, in which case the isolator output
is forced to a default state (see Table 17 and Table 18) by the
watchdog timer circuit.
For example, at a magnetic field frequency of 1 MHz, the POWER CONSUMPTION
maximum allowable magnetic field of 0.2 kgauss induces a The supply current at a given channel of the ADuM120x
voltage of 0.25 V at the receiving coil. This is about 50% of the isolator is a function of the supply voltage, the data rate of the
sensing threshold and does not cause a faulty output transition. channel, and the output load of the channel.
Similarly, if such an event occurs during a transmitted pulse
(and has the worst-case polarity), it reduces the received pulse For each input channel, the supply current is given by
from >1.0 V to 0.75 V—still well above the 0.5 V sensing IDDI = IDDI (Q) f ≤ 0.5fr
threshold of the decoder.
IDDI = IDDI (D) × (2f − fr) + IDDI (Q) f > 0.5fr
The preceding magnetic flux density values correspond to
specific current magnitudes at given distances away from the For each output channel, the supply current is given by
ADuM120x transformers. Figure 14 expresses these allowable IDDO = IDDO (Q) f ≤ 0.5fr
current magnitudes as a function of frequency for selected −3
IDDO = (IDDO (D) + (0.5 × 10 ) × CLVDDO) × (2f − fr) + IDDO (Q)
distances. As seen, the ADuM120x are extremely immune and f > 0.5fr
can be affected only by extremely large currents operating very
close to the component at a high frequency. For the 1 MHz where:
example, a 0.5 kA current would have to be placed 5 mm away IDDI (D), IDDO (D) are the input and output dynamic supply currents
from the ADuM120x to affect the operation of the component. per channel (mA/Mbps).
1000
CL is the output load capacitance (pF).
DISTANCE = 1m
VDDO is the output supply voltage (V).
MAXIMUM ALLOWABLE CURRENT (kA)
f is the input logic signal frequency (MHz, half of the input data
100
rate, NRZ signaling).
fr is the input stage refresh rate (Mbps).
10 IDDI (Q), IDDO (Q) are the specified input and output quiescent
DISTANCE = 100mm supply currents (mA).
1
To calculate the total IDD1 and IDD2 supply currents, the supply
DISTANCE = 5mm
currents for each input and output channel corresponding to
0.1 IDD1 and IDD2 are calculated and totaled. Figure 6 and Figure 7
provide per-channel supply currents as a function of data rate
0.01
for an unloaded output condition. Figure 8 provides per-
04642-014
1k 10k 100k 1M 10M 100M channel supply current as a function of data rate for a 15 pF
MAGNETIC FIELD FREQUENCY (Hz) output condition. Figure 9 through Figure 11 provide total
Figure 14. Maximum Allowable Current for Various VDD1 and VDD2 supply current as a function of data rate for
Current-to-ADuM120x Spacings
ADuM1200 and ADuM1201 channel configurations.
Note that, at combinations of strong magnetic fields and high
frequencies, any loops formed by PCB traces can induce suffi-
ciently large error voltages to trigger the threshold of succeeding
circuitry. Care should be taken in the layout of such traces to
avoid this possibility.
INSULATION LIFETIME In the case of unipolar ac or dc voltage, the stress on the insu-
All insulation structures eventually break down when subjected lation is significantly lower, which allows operation at higher
to voltage stress over a sufficiently long period. The rate of insu- working voltages yet still achieves a 50-year service life. The
lation degradation is dependent on the characteristics of the working voltages listed in Table 14 can be applied while main-
voltage waveform applied across the insulation. In addition taining the 50-year minimum lifetime provided the voltage
to the testing performed by the regulatory agencies, Analog conforms to either the unipolar ac or dc voltage cases. Any cross-
Devices carries out an extensive set of evaluations to determine insulation voltage waveform that does not conform to Figure 16
the lifetime of the insulation structure within the ADuM120x. or Figure 17 is to be treated as a bipolar ac waveform, and its
peak voltage is to be limited to the 50-year lifetime voltage value
Analog Devices performs accelerated life testing using voltage listed in Table 14.
levels higher than the rated continuous working voltage. Accel-
eration factors for several operating conditions are determined. Note that the voltage presented in Figure 16 is shown as sinu-
These factors allow calculation of the time to failure at the actual soidal for illustration purposes only. It is meant to represent any
working voltage. The values shown in Table 14 summarize the voltage waveform varying between 0 V and some limiting value.
peak voltage for 50 years of service life for a bipolar ac operating The limiting value can be positive or negative, but the voltage
condition and the maximum CSA/VDE approved working volt- cannot cross 0 V.
ages. In many cases, the approved working voltage is higher than RATED PEAK VOLTAGE
the 50-year service life voltage. Operation at these high working
04642-021
0V
voltages can lead to shortened insulation life in some cases.
Figure 15. Bipolar AC Waveform
The insulation lifetime of the ADuM120x depends on the
voltage waveform type imposed across the isolation barrier.
The iCoupler insulation structure degrades at different rates
RATED PEAK VOLTAGE
depending on whether the waveform is bipolar ac, unipolar
04642-022
ac, or dc. Figure 15, Figure 16, and Figure 17 illustrate these
different isolation voltage waveforms, respectively. 0V
Figure 16. Unipolar AC Waveform

Bipolar ac voltage is the most stringent environment. The goal
of a 50-year operating lifetime under the ac bipolar condition
determines the Analog Devices recommended maximum
RATED PEAK VOLTAGE
working voltage.
04642-023
0V
Figure 17. DC Waveform
OUTLINE DIMENSIONS
5.00 (0.1968)
4.80 (0.1890)
8 5
4.00 (0.1574) 6.20 (0.2441)
3.80 (0.1497) 1 5.80 (0.2284)
4
1.27 (0.0500) 0.50 (0.0196)

BSC 45°
1.75 (0.0688) 0.25 (0.0099)
0.25 (0.0098) 1.35 (0.0532)
8°
0.10 (0.0040) 0°
COPLANARITY 0.51 (0.0201)
0.10 1.27 (0.0500)
0.31 (0.0122) 0.25 (0.0098)
SEATING 0.40 (0.0157)
PLANE 0.17 (0.0067)
COMPLIANT TO JEDEC STANDARDS MS-012-AA

CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
012407-A
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
Figure 18. 8-Lead Standard Small Outline Package [SOIC_N]

Narrow Body (R-8)
Dimensions shown in millimeters and (inches)
ORDERING GUIDE
Number Number Maximum Maximum Maximum
of Inputs, of Inputs, Data Rate Propagation Pulse Width Temperature Package
Model1, 2 VDD1 Side VDD2 Side (Mbps) Delay, 5 V (ns) Distortion (ns) Range Option3
ADuM1200AR 2 0 1 150 40 −40°C to +105°C R-8
ADuM1200ARZ 2 0 1 150 40 −40°C to +105°C R-8
ADuM1200ARZ-RL7 2 0 1 150 40 −40°C to +105°C R-8
ADuM1200BR 2 0 10 50 3 −40°C to +105°C R-8
ADuM1200BR-RL7 2 0 10 50 3 −40°C to +105°C R-8
ADuM1200BRZ 2 0 10 50 3 −40°C to +105°C R-8
ADuM1200BRZ-RL7 2 0 10 50 3 −40°C to +105°C R-8
ADuM1200CR 2 0 25 45 3 −40°C to +105°C R-8
ADuM1200CR-RL7 2 0 25 45 3 −40°C to +105°C R-8
ADuM1200CRZ 2 0 25 45 3 −40°C to +105°C R-8
ADuM1200CRZ-RL7 2 0 25 45 3 −40°C to +105°C R-8
ADuM1200WSRZ 2 0 1 150 40 −40°C to +125°C R-8
ADuM1200WSRZ-RL7 2 0 1 150 40 −40°C to +125°C R-8
ADuM1200WTRZ 2 0 10 50 3 −40°C to +125°C R-8
ADuM1200WTRZ-RL7 2 0 10 50 3 −40°C to +125°C R-8
ADuM1200WURZ 2 0 25 45 3 −40°C to +125°C R-8
ADuM1200WURZ-RL7 2 0 25 45 3 −40°C to +125°C R-8
ADuM1201AR 1 1 1 150 40 −40°C to +105°C R-8
ADuM1201AR-RL7 1 1 1 150 40 −40°C to +105°C R-8
ADuM1201ARZ 1 1 1 150 40 −40°C to +105°C R-8
ADuM1201ARZ-RL7 1 1 1 150 40 −40°C to +105°C R-8
ADuM1201BR 1 1 10 50 3 −40°C to +105°C R-8
ADuM1201BR-RL7 1 1 10 50 3 −40°C to +105°C R-8
ADuM1201BRZ 1 1 10 50 3 −40°C to +105°C R-8
ADuM1201BRZ-RL7 1 1 10 50 3 −40°C to +105°C R-8
ADuM1201CR 1 1 25 45 3 −40°C to +105°C R-8
ADuM1201CRZ 1 1 25 45 3 −40°C to +105°C R-8
ADuM1201CRZ-RL7 1 1 25 45 3 −40°C to +105°C R-8
Number Number Maximum Maximum Maximum
of Inputs, of Inputs, Data Rate Propagation Pulse Width Temperature Package
Model1, 2 VDD1 Side VDD2 Side (Mbps) Delay, 5 V (ns) Distortion (ns) Range Option3
ADuM1201WSRZ 1 1 1 150 40 −40°C to +125°C R-8
ADuM1201WSRZ-RL7 1 1 1 150 40 −40°C to +125°C R-8
ADuM1201WTRZ 1 1 10 50 3 −40°C to +125°C R-8
ADuM1201WTRZ-RL7 1 1 10 50 3 −40°C to +125°C R-8
ADuM1201WURZ 1 1 25 45 3 −40°C to +125°C R-8
ADuM1201WURZ-RL7 1 1 25 45 3 −40°C to +125°C R-8
1
Z = RoHS Compliant Part.
2
W = Qualified for Automotive Applications.
3
R-8 = 8-lead narrow-body SOIC_N.
AUTOMOTIVE PRODUCTS
The ADuM1200W/ADuM1201W models are available with controlled manufacturing to support the quality and reliability requirements
of automotive applications. Note that these automotive models may have specifications that differ from the commercial models; therefore,
designers should review the Specifications section of this data sheet carefully. Only the automotive grade products shown are available for
use in automotive applications. Contact your local Analog Devices account representative for specific product ordering information and
to obtain the specific Automotive Reliability reports for these models.
©2004–2012 Analog Devices, Inc. All rights reserved. Trademarks and

registered trademarks are the property of their respective owners.
D04642-0-3/12(I)

Dual-Channel Digital Isolators Adum1200/Adum1201: Data Sheet

Uploaded by

Copyright:

Available Formats

Dual-Channel Digital Isolators Adum1200/Adum1201: Data Sheet

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Dual-Channel Digital Isolators Adum1200/Adum1201: Data Sheet

Uploaded by

Copyright:

Available Formats

Dual-Channel Digital Isolators

Data Sheet ADuM1200/ADuM1201

APPLICATIONS VIA 2 ENCODE DECODE 7 VOA

Size-critical multichannel isolation VIB 3 ENCODE DECODE 6 VOB

GENERAL DESCRIPTION VDD1 1 8 VDD2

these isolation components provide outstanding performance GND1 4 5 GND2

characteristics superior to alternatives, such as optocouplers.

Package Characteristics ............................................................. 19 Ordering Guide .......................................................................... 27

Regulatory Information............................................................. 19 Automotive Products ................................................................. 28

Insulation and Safety-Related Specifications.......................... 19

3/08—Rev. E to Rev. F 9/04—Rev. A to Rev. B

INSULATION AND SAFETY-RELATED SPECIFICATIONS

RECOMMENDED OPERATING CONDITIONS

180 Table 12.

0 50 100 150 200 magnetic fields.

Figure 3. Thermal Derating Curve, Dependence of Safety-Limiting Values

ABSOLUTE MAXIMUM RATINGS

Table 14. Maximum Continuous Working Voltage1

PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS

Figure 4. ADuM1200 Pin Configuration Figure 5. ADuM1201 Pin Configuration

Table 17. ADuM1200 Truth Table (Positive Logic)

Table 18. ADuM1201 Truth Table (Positive Logic)

TYPICAL PERFORMANCE CHARACTERISTICS

INPUT (VIx) 50%

Channel-to-channel matching refers to the maximum amount

that the propagation delay differs between channels within a 10

Propagation delay skew refers to the maximum amount that 1

the propagation delay differs between multiple ADuM120x

DC CORRECTNESS AND MAGNETIC FIELD IMMUNITY

1k 10k 100k 1M 10M 100M

the 50-year service life voltage. Operation at these high working

Figure 16. Unipolar AC Waveform

Figure 17. DC Waveform

1.27 (0.0500) 0.50 (0.0196)

COMPLIANT TO JEDEC STANDARDS MS-012-AA

Figure 18. 8-Lead Standard Small Outline Package [SOIC_N]

©2004–2012 Analog Devices, Inc. All rights reserved. Trademarks and

You might also like