Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 229 views

    Inspection Dishend

    Uploaded by

    Varun Malhotra
    The inspection report summarizes the dimensions of a dished end that was fabricated for Times Automation Pvt. Ltd. It lists 4 dimensions that were checked - dish outer diameter, dish center-to-face, dish straight face, and dish height. All dimensions were within the required specifications except for dish height, which was slightly larger than required but noted as acceptable.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd

    Inspection Dishend

    Uploaded by

    Varun Malhotra
    229 views5 pages
    The inspection report summarizes the dimensions of a dished end that was fabricated for Times Automation Pvt. Ltd. It lists 4 dimensions that were checked - dish outer diameter, dish center-to-face, dish straight face, and dish height. All dimensions were within the required specifications except for dish height, which was slightly larger than required but noted as acceptable.

    Original Description:

    Inspection Dishend

    Copyright

    © © All Rights Reserved

    Available Formats

    DOCX, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The inspection report summarizes the dimensions of a dished end that was fabricated for Times Automation Pvt. Ltd. It lists 4 dimensions that were checked - dish outer diameter, dish center-to-face, dish straight face, and dish height. All dimensions were within the required specifications except for dish height, which was slightly larger than required but noted as acceptable.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    229 views5 pages

    Inspection Dishend

    Uploaded by

    Varun Malhotra
    The inspection report summarizes the dimensions of a dished end that was fabricated for Times Automation Pvt. Ltd. It lists 4 dimensions that were checked - dish outer diameter, dish center-to-face, dish straight face, and dish height. All dimensions were within the required specifications except for dish height, which was slightly larger than required but noted as acceptable.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    of 5

    INSPECTION REPORT DISHEND

    CLIENT : Times Automation Pvt. Ltd. M.O.C – M.S.


    Draw No : As per client drawing
    Fabrication Code : ASME SEC-VIII, DIV-I

    S.NO DESCRIPTION REQUIRED OBSERVED REMARK


    SIZE IN mm SIZE IN mm

    01 DISH OD 2500 2499 OK


    02 DISH CF 7854 7852 OK
    03 DISH SF 50 50 TO 55 OK
    04 Dish Height 534 540 Ok , observed outside

    Mr. Varun Malhotra

    M/S Times Automation Pvt. Ltd. M/S Malik Polychem Ltd.


    DISHED END FORMATION REPORT
    CLIENT : CAPACITY:
    EQUIPMENT:
    Draw No. : JOB CODE:
    Fabrication Code: ASME SEC-VIII, DIV-I
    Dish ID Req. Observed Thickness Req. Obs.
    THK . Circ. Circ. SKETCH
    SF KR CR Avg.
    B.D.E

    T.D.E

    Inside Dia. Height Straight Face


    ( I.R ) ( S.F )
    Req. Obs. Req. Obs Req. Obs.

    B.D.E

    T.D.E
    All Dimensions are in mm.
    B.D.E  Bottom Dished End
    T.D.E  Top Dished End
    J.D. E  Jacket Dished End

    Malik Polychem Ltd.

    RUN TEST REPORT


    CLIENT : CAPACITY:
    EQUIPMENT : INSPECTION AGENCY: M.P.L
    Draw No. : JOB CODE:
    AIR. NO.: TYPE: 88B2A1CG

    1. SEAL MAKE

    SYPHON SYSTEM:
    2.SHAFT DETAIL
    3. BAFFLE DETAIL

    SR. NO. : TYPE :


    4. GEAR BOX DETAILS
    MAKE : RATIO

    MOTOR CURRENT ( AMP ) : R: 15 Y: 14 B: 16

    5. MOTOR DETAILS RESULT : TESTING WAS DONE WITH OUT LOAD.


    REF NO. TYPE :

    HP. : RPM. : MAKE :


    DISTANCE BETWEEN
    AGI. & BTM. D’END:
    NO
    7 ADDITIONAL REQI. :

    SATISFACTORY
    8. REMARK :

    FOR (Q.C) FOR CLIENT

    HYDRO TESTING REPORT


    CLIENT : CAPACITY :
    EQUIPMENT : INSPECTION AGENCY: M.P.L
    Draw No. : JOB CODE:
    A) MAIN SHEEL ( HYDRO )

    Working Pressure Design Pressure Test Pressure Position Date Of Result Q.C.
    Kg/cm2 Kg/cm2 (Kg/cm2) Testing Sign

    Holding Time Pr. Gauge # 1 Pr. Gauge # 2


    Calibration Date Calibration Date
    Calibration Due Calibration Due
    Date Date

    B) LIMPET ( HYDRO )

    Working Pressure Design Pressure Test Pressure Position Date Of Result Q.C.
    Kg/cm2 Kg/cm2 (Kg/cm2) Testing Sign

    Holding Time Pr. Gauge # 1 Pr. Gauge # 2


    Calibration Date Calibration Date
    Calibration Due Calibration Due
    Date Date
    REMARKS:1.MAIN SHELL HYDRO PRESSER TESTING NOT DONE DUE TO SHAFT NOT FIXED.
    2. IF ANY DAMAGE DURING TRANSPORTATION BECAUSE OF PACKING THAT IS
    RESPONSIBILITY OF M.P.LTD.
    3. FINAL COMMISSINING WILL BE DONE BY M/s M.P.LTD AT PDLTD LALRU.
    4. ALL NOZZLES AS PER DESIGNING.

    Parabolic drugs Ltd Malik Polychem Ltd.

    You might also like