Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

Using Source Shifting and Source Transformation Techniques, Calculate V For The Circuit Shown in Fig.Q1 (B)

Download as pdf or txt
Download as pdf or txt
You are on page 1of 6

17EC35

Visvesvaraya Technological University, Belagavi


MODEL QUESTION PAPER
3rd Semester, B.E (CBCS 2017-18 Scheme)EC/TC
Course: 17EC35- Network Analysis, Set No. 1

Time: 3 Hours Max. Marks: 100

Note: (i) Answer Five full questions selecting any one full question from each Module.
(ii) Question on a topic of a Module may appear in either its 1st or/and 2nd question.

Module-1 Marks
1 a. Derive the expression for i) ∆ to Ү transformation ii)Ү to ∆ 10
transformation.
b. Using source shifting and source transformation techniques, calculate Vad 10
for the circuit shown in Fig.Q1 (b).

Fig. Q1(b)
OR
2 a. Determine the equivalent resistance across the terminals a and b, 5
shown in Fig.Q2(a)

Fig.Q2(a)
b. Determine the value ofvx using mesh analysis for Fig.Q2 (a) shown 5
below.
Fig.Q2(a)

c. For the network of Fig.Q2(b), determine the node voltage by nodal 10


analysis.

Fig.Q2(b)
Module-2
3 a. State superposition theorem. In the circuit of Fig.Q3(a),use the 10
superposition principle to determine the value of ix.

Fig.Q3(a)
b. Obtain the Thevenin’s and Norton’s equivalent for the network shown in 10
Fig.Q3 (b).
Fig.Q3(b)
OR
4 a. State and explain maximum power transfer theorem. 4
b. Using Millman’s theorem, find IL through RL for the network shown in 6
Fig.Q4 (b).

Fig.Q4(b)
c. State and verify reciprocity theorem for the circuit shown in Fig.Q4(c). 10

Fig.Q4(c)
Module-3
5 a. State and prove initial value theorem and final value theorem. 10
b. In the circuit shown in Fig.Q5(b), the switch was inposition a 10
forsufficiently long time to have achieved steady state.At t=0, the switch
was changed from a tob. Determine IL and VC, their first and second
order derivatives at t=0+.

Fig.Q5 (b)
OR
6 a. The switch in the network shown in Fig.Q6 (a) is closed at t=0.Determine 10
the voltage across capacitor. Use Laplace transform.

Fig.Q6(a)
b. Determine the Laplace transform of the periodic saw tooth waveform of 10
Fig.Q6 (b).Use gate function.

Fig.Q6 (b)
Module-4
7 a. What is resonance?Derive an expression for half power cutoff 8
frequencies.
b. Define Q-factor, resonant frequency, selectivity and bandwidth. 4
c. A series RLC circuit consists of R=10Ω, L=0.01H and C=0.01µF is 8
connected across a supply of 10mV.Determine,i)f0 ii)Q-factor iii)BW iv)f1
and f2 v)I0.
OR
8 a. Prove that for a series resonant circuit, the resonant frequency is the 4
geometric mean of two half power frequencies.
b. Obtain the expression for the resonant frequency for the circuit shown 8
in Fig.Q8 (b).

Fig.Q8 (b)
c. Find the value of L for which the circuit shown in Fig.Q8(c) is resonant at 8
a frequency of w=5000 rad/sec.

Fig.Q8(c)
Module-5
9 a. Define y-parameters. Also, find y-parameters for the two-port –network 10
shown in Fig.Q9 (a).

Fig.Q9 (a).
b. Define ABCD parameters. Express y-parameters in terms of ABCD 10
parameters.
OR
10 a. Define hybrid parameters (h). Express hybrid parameters in terms of 10
impedance parameters (z).
b. Define z parameters. Also, find z parameters for the network shown in 10
Fig.Q10 (b).

Fig.Q10 (b).

**********

You might also like