IEEE STANDARDS

802.3,802.4,802.5
 INTRODUCTION
IEEE 802 refers to a family of IEEE standards
 Dealing with local area network and metropolitan area network.
 Restricted to networks carrying variable-size packets.
 Specified in IEEE 802 map to the lower two layers
 Data link layer
 Physical layer

The most widely used standards

.802.3 - Ethernet
802.4 - Token Bus
802.5 - Token Ring
 ETHERNET (IEEE 802.3 )
The IEEE 802.3 standard specifies the CSMA/CD (Carrier Sense Multiple
Access with Collision Detection) media access control method. CSMA/CD is
the most commonly employed access method for LANs using a bus or tree
topology. It is the media access control method used by Ethernet[1].
Most widely type used at present, with a huge installed base and considerable
operational experience.
Protocol is very simple
Stations can be added without making the network down.
The delay at low load is practically zero. (no token waiting) 3
ETHERNET CABLING

The most common kinds of Ethernet cabling.

ETHERNET SIGNALLING

(a) Binary encoding, (b) Manchester encoding,

(c) Differential Manchester encoding.
CSMA/CD TRANSMISSION FRAME
 Preamble
The preamble is responsible for providing the synchronization between the sending and receiving
device.It is a series of 56 bits (7 bytes) of alternating 1s and 0s found at the beginning of the frame[2]
 Start of Frame Delimiter
The start frame delimiter follows the preamble. As its name implies, it indicates the start of the data frame.
The start frame delimiter is 1 byte in length—made up of the following 8-bit sequence—10101011[3].
 Address Fields
Each of the address fields—the destination address and the source address—can be either 2 bytes or 6
bytes in length. If universal addressing is used, the addresses must be 6 bytes each. But if local addressing is
used they may be either 2 or 6 bytes long. Both destination and source addresses must be of the same length
for all devices on a given network[2].
 Length Count
This is a 2-byte field indicating the length of the data field that follows. It is needed to determine the
length of the data field in those cases when a pad field is used[2].
Information Field
The information field contains the actual data packet to be transmitted. Its
length is variable[2].
 Pad Field
A pad field is used to ensure that the frame meets a minimum length
requirement. A frame must contain a minimum number of bytes in order for
stations to detect collisions accurately[2].
Frame Check Sequence
The frame check field is used as an error-control mechanism. When the
transmitting device assembles a frame, it performs a calculation on the bits in
the frame. The algorithm used to perform this calculation always results in a 4-
byte value. The sending device stores this value in the frame check sequence
field[2].
TOKEN BUS (IEEE 802.4)
• The IEEE 802.4 standard specifies the Token-bus media access control method. It is
one of two token passing access methods. IEEE 802.4 is based on a physical bus or tree
topology. The Token-bus approach requires a station to have possession of a token in
order to transmit. The token is passed from station to station in a logical ring[3].
• Uses highly reliable cable television equipments.
• It is more deterministic than 802.3, although repeated loss of token at critical times
can introduce the uncertainness.
• Can easily handle shorter frames. (no limitation on frame size)
• It supports priorities and hence suitable for Real Time traffic.
• It also has excellent throughput and efficiency at high load.
TOKEN-BUS TRANSMISSION FRAME
 Preamble
The preamble is responsible for providing the synchronization between the sending and receiving device. The
length of this field and its contents depend on the modulation method being used and the speed of the
network.
 Start of Frame
The start delimiter follows the preamble. As its name implies, it indicates the start of the data frame. The start
frame delimiter is 1 byte in length and contains a signaling pattern that is always different from the data—
the actual signaling pattern varies with the encoding scheme used[5].
 Frame Control
This field identifies the type of frame being sent—Logical Link Control data frames, token control frames,
Media Access Control management data frames, or special-purpose data frames.
 Address Fields
Each of the address fields—the destination address and the source address—can be either 2 bytes (16-bit
addresses) or 6 bytes (48-bit addresses) in length. If universal addressing is used, the addresses must be 6
bytes each. But if local addressing is used they may be either 2 or 6 bytes long. Both destination and source
addresses must be of the same length for all devices on a given network. The source address must be for an
individual device. The destination address can be an individual address, a group address or a broadcast
address[5].
Information Field
The information field contains the actual data packet to be transmitted. Its length is variable. It
may contain a Logical Link protocol data unit, token control data, management data or special-
purpose data—as indicated in the frame control field.
Frame Checksum
The frame check field is used as an error control mechanism. When the transmitting device
assembles a frame, it performs a calculation on the bits in the frame. The algorithm used to
perform this calculation always results in a 4-byte value. The sending device stores this value
in the frame check sequence field. When the destination device receives the frame, it performs
the same calculation and compares the result to that in the frame check sequence field. If the
two values are the same, the transmission is assumed to be correct. If the two values are
different, the destination device can request a retransmission of the frame[5].
 End of Frame
The end delimiter marks the end of the frame and shows the position of the frame check
sequence field. Just as with the start delimiter, the signaling value is always different from the
data.
TOKEN RING (IEEE 802.5)
• IEEE 802.5 is the second of the token passing access control methods. Token-ring is
most commonly used in a network structure following both a logical and physical ring
topology. The right to transmit is controlled by a token[3].
• It uses point-to-point connections and hence the engineering is easy.
• Any transmission media can be used.
• The use of wire centers make the token ring the only LAN that can detect and eliminate
cable failures automatically.
• Like 802.4, priorities also possible, although the scheme is not as fair.
• Very short and very large frames both are possible.
• At very high load, the throughput and efficiency are excellent.
TOKEN-RING TRANSMISSION FRAME
 Start of frame
The starting delimiter indicates the start of the data frame. It uses a unique signal pattern that does not
correspond to either a 0 or 1 bit. These are known as nondata values and ensure that no data sequence
will ever be mistaken for a delimiter.
 Access Control Field
This field identifies whether the frame is a data frame or a token. It contains a bit used to identify a
constantly busy token, a priority bit and reservations bits.
 Frame Control Field
This field identifies the frame type and for certain types of control frames, the function it is to perform.
 Address Fields
Each of the address fields—the destination address and the source address—can be either 2 bytes (16-bit
addresses) or 6 bytes (48-bit addresses) in length. If universal addressing is used, the addresses must be 6
bytes each. But if local addressing is used they may be either 2 or 6 bytes long. Both destination and
source addresses must be of the same length for all devices on a given network.
The source address must be for an individual device. The destination address can be an individual address,
a group address or a broadcast address.
 Information Field
The information field contains the actual data packet to be transmitted. This can be either a protocol data unit being
passed from the logical link control sublayer or control information supplied by the media access control sublayer. Its
length is variable anywhere from 0 to 17800 bytes in length.
 Frame Check Sequence
The frame check field is used as an error control mechanism. When the transmitting device assembles a frame, it
performs a calculation on the bits in the frame. The algorithm used to perform this calculation always results in a 4 byte
value. The sending device stores this value in the frame check sequence field. When the destination device receives the
frame, it performs the same calculation and compares the result to that in the frame check sequence field. If the two
values are the same, the transmission is assumed to be correct. If the two values are different, the destination station can
request a retransmission of the frame.
 Ending Delimiter
This identifies the end of the frame by containing nondata values. It also contains bits used to identify whether or not it is
the last frame in a multiframe transmission and if an error has been detected by any station.
 Frame Status Field
The frame status field contains the address recognized and frame copied control bits.
 REFERENCE
[1]. http://www.erg.abdn.ac.uk/users/gorry/course/lan-pages/csma-cd.html
[2]. http://www.erg.abdn.ac.uk/users/gorry/course/lan-pages/enet.html
[3]. G. Watson, A. Albrecht, J. Curcio, D. Dove, S. Goody, J. Grinham, M.P. Spratt, and P.A. Thaler.
The demand priority MAC protocol. IEEE Network, 9(1):28–34, Jan./Feb. 1995.
[4]. R. Yavatkar, P. Pai, and R. Finkel. A reservation-based CSMA protocol for inte-grated manufacturing
networks. IEEE Transactions on Systems, Man, and Cybernet-ics, 24(8):1247–1258, Aug. 1994.
[5]. Q. Zheng and K.G. Shin. On the ability of establishing real-time channels in point-to-point
packet-switched networks. IEEE Transactions on Communications, 42(2/3/4):1096–1105,
Feb./Mar./Apr. 1994.
THANK YOU