h12 211
h12 211
1 of 213
Huawei - H12-211
Which command should be used to check the mapping between protocol addresses and frame relay addresses?
A. display fr interface
B. display fr map-info
C. display fr inarp-info
Answer: B
A. None
B. Local
C. Radius
D. 802.1X
Answer: B
Refer to the graphic.RTA and RTB connect to a Frame Relay switch and use dynamic address mapping. The
command “fr map ip 10.0.1.1 32” is then configured on RTB, without using the undo inarp command. What
will occur as a result? (Choose two).
Answer: A C
2 of 213
Huawei - H12-211
Which of the following storage devices is used to store the startup configuration files in a router?
<choice ident="A">
<choice ident="B">
<choice ident="C">
<choice ident="D">
A. SDRAM
B. NVRAM
C. Flash
D. BootROM
Answer: B
Which of the following statements about gratuitous ARP packets are true? (Choose two)
A. A system can determine whether conflicting IP addresses are used by sending a gratuitous ARP packet
B. A gratuitous ARP packet uses the same format as an ARP request packet.
D. A gratuitous ARP packet uses the same format as an ARP reply packet.
Answer: A B
Which of the following problems are caused by routing loops? (Choose three)
A. Slow convergence
C. Router restarting
3 of 213
Huawei - H12-211
Answer: A B D
What is the meaning of 200 in the command "fr map ip 10.1.1.2 200"?
B. local DLCI
C. remote interface ID
D. remote node ID
Answer: B
The users who log on the router through Telnet are not permitted to configure IP address. What is the possible
reason?
Answer: C
Two routers are configured with OSPFv3. OSPFv3 is enabled on all interfaces of each router. Which of the
following is true in the event that the network administrator does not configure a Router-ID?
D.
4 of 213
Huawei - H12-211
Answer: D
Which of the following statements regarding the verification of IP connectivity are false? (Choose three)
A. The ping 127.0.0.1 command can be used to check whether the network cable is correctly inserted into
the host’s Ethernet port.
B. The ping command with the host IP address as the destination can be used to verify that the TCP/IP
protocol suite is functioning correctly.
C. The ping command can be used to verify connectivity between the host and the local gateway.
D. The command “ipconfig /release” can be used to check connectivity problems between the host and the
local gateway.
Answer: A B D
Which of the following commands is used to enter the system-view from the user view on a Huawei router?
A. system-view
B. enable
C. configure terminal
D. interface system
Answer: A
The administrator has configured an IP address for Host A and Host B, but had forgotten to configure a default
gateway. What effect will this have on the hosts?
A. Neither host will be affected, and therefore will be able to communicate with the peer.
5 of 213
Huawei - H12-211
D. The host will be unable to reach neither the local nor remote network destinations .
Answer: C
A network administrator uses the ping command to check for points of failure in the network. Which protocols
will be used during this process? (Choose two)
<choice ident=“A”>
<choice ident=“B”>
<choice ident=“C”>
<choice ident=“D”>
A. ICMP
B. TCP
C. ARP
D. UDP
Answer: A C
Refer to the graphic. The data is transmitted using IPsec tunnel mode. The fields of which headers will be
authenticated?
Answer: C
6 of 213
Huawei - H12-211
On the interface serial 1/0/1 of RTA, the command “ip address unnumbered interface loopback 0” has been
configured. Which following statements are correct? (Choose two).
Answer: B D
A DHCP server in the enterprise network is being used to allocated IP addresses to hosts. An administrator
discovers however that some hosts are obtaining IP addresses outside of the scope of the DHCP server’s
address pool. What are the possible reasons for this? (Choose three).
A. Another DHCP server exists in the network and is allocating IP addresses to hosts that happen to be
within a closer proximity than the authorized DHCP server
B. The hosts were unable to discover a DHCP server and therefore generated their own address in the
C. The hosts were unable to discover a DHCP server and therefore generated their own address in the
Answer: A B D
The network administrator needs to configure static NAT on RTA, in order to allow Host A to communicate
with Host C. Which command is correct?
7 of 213
Huawei - H12-211
Answer: D
<Huawei>display startup
MainBoard:
D. The next startup system software can be changed by using the “startup system software
<startup-softwarename>.cc” command.
Answer: C
Which of the following storage devices are supported by Huawei router? (Select 4 Answers)
A.
8 of 213
Huawei - H12-211
A. SDRAM
B. NVRAM
C. Flash
D. Hard Disk
E. CF Card
Answer: A B C E
Which of the following commands can be used to display mapping relationship between network address and
DLCI?
A. display fr interface
B. display fr
C. display fr map-info
D. display fr brief
Answer: C
Refer to the graphic. RTA and RTB are connected over a Frame Relay network using a DLCI, as shown. Static
mapping is required on RTA. Which of the following commands will achieve this?
Answer: C
Which of the following commands is used to enable dynamic address mapping protocol in the interface
9 of 213
Huawei - H12-211
A. fr inarp
B. fr reverse-arp
C. inverse-arp
D. reverse-arp
Answer: A
Refer to the configuration output. What does the value “2000” refer to?
D. It represents the number of bytes that can be translated before the address is returned to the public
address pool.
Answer: A
A. multiple areas
B. Router-ID
C. authentication
D. multicast updates
Answer: C
10 of 213
Huawei - H12-211
[Huawei-ip-pool-pool1]gateway-list 10.10.10.1
Refer to the configuration output. The administrator wishes to configure the DHCP server pool in order to
assign an IP address to the customer’s terminal device.
Which command should be included in the configuration to provide the minimal lease period for IP addresses?
B. lease day 1
C. lease 24
D. lease 0
Answer: B
An AR2200 router in the company network cannot boot. In order to resolve this, the administrator wishes to
update the VRP software. What should he/she do?
A. The administrator should use a console cable to connect the router and host, and directly upgrade the
device.
B. The administrator should use FTP to transfer the VRP software, by configuring the AR2200 router as an
FTP client.
C. The administrator should use DHCP to boot the AR2200, and then use the AR2200 router as a TFTP
client to download the VRP software from the server.
D. The administrator should use the telnet command on the client to remote access the device, and upgrade
the VRP software.
Answer: B
The administrator wishes to update the configuration file of an AR2200 router using a USB cable. How can
this be achieved? (Choose two)
A.
11 of 213
Huawei - H12-211
A. The administrator should connect the USB cable between the terminal and the mini USB port of the
AR2200 router.
B. The administrator should connect the USB cable between the terminal and the USB port of the AR2200
router.
C. The AR2200 router cannot support configuration updates through a USB cable.
D. The administrator should install the mini USB drivers on the terminal after connecting the USB.
Answer: A D
The administrator wishes to configure OSPF on a router in the network however the router has no loopback
interface. Which value will be used as the router ID?
Answer: B
An ARP request is sent by host A to obtain the destination MAC address of host D. Which statement is true
about regarding the ARP reply?
A. The destination MAC address of this frame is the MAC address of Switch A.
C. The destination MAC address of this frame is the MAC address of Host A.
Answer: C
Which of the following IPv6 addresses can be configured on a router’s interface? (Choose two).
12 of 213
Huawei - H12-211
A. fe80:13dc::1/64
B. ff00:8a3c::9b/64
C. ::1/128
D. 2001:12e3:1b02::21/64
Answer: A D
Which of the following commands can switch a view from the system view to the user view?
A. System-view
B. Router
C. Quit
D. User-view
Answer: C
Which of the following statements explains the behavior of the ICMP redirect function? (Choose two)
A. When a router receives data on the interface via which the same data needs to be forwarded, and the
source is on the same segment as the next hop, an ICMP redirect message will be sent by the router to
the source.
B. When a router receives data on an interface, and the router’s IP address matches the destination IP of the
data, an ICMP redirect message will be sent by the router to the source.
C. When a router receives data on the interface via which the same data needs to be forwarded, and the
source is on the same segment as the next hop, an ICMP Redirect message will be sent by the source to
the router.
D. When a router receives data on the interface via which the same data needs to be forwarded, and the
source is on a different segment from the next hop, an ICMP redirect message will be sent by the router
to the source
Answer: A D
13 of 213
Huawei - H12-211
Refer to the graphic. The network administrator wishes to aggregate the two links as member interfaces of
Ethtrunk
B. The interfaces will be aggregated, but only interface GE0/0/1 will send data flow.
C. The interfaces will be aggregated, but the Eth-trunk will not be active.
Answer: D
Which of the following statements are correct about NAT? (Choose three)
B. NAT is used for translation between private and public network addresss.
C. When hosts inside a private network access the outside network, NAT is not required.
Answer: A B D
Which of the following authentication methods are supported for Telnet users? (Choose three)
A. Password authentication
C. MD5 authentication
D. No authentication
Answer: A B D
14 of 213
Huawei - H12-211
Which of the following types can ICMP packets be classified into? (Choose two)
Answer: B C
<Huawei>system-view
[Huawei]history-command max-size 20
Refer to the command output. Which statements regarding the shown command are true? (Choose two)
A. The command is used to adjust the size of the history command buffer
Answer: A C
How many probe packets are sent for each TTL value by default when "tracert" is used to detect the path along
which packet is sent from source to destination?
A. 3
B. 4
C. 6
D. 8
Answer: A
15 of 213
Huawei - H12-211
An adminstrator has been requested to replace the configuration file of a router in the network. The
administrator has been instructed that after logging into the router, he must first permenantly erase the current
configuration file config.zip from the system. Which command should he use to achieve this?
C. reset config.zip
D. clear config.zip
Answer: B
Which of the following regarding Frame Relay DLCI are correct? (Choose three)
Answer: A C D
A host has established a telnet connection with the router attached to interface G0/0/0. Which of the following
statements are correct? (Choose two)
A. The destination address of a frame sent by the host will be the MAC address of the router interface.
B. The destination address of a frame will be the MAC address of the switch interface.
C. The destination port number in a segment header will have a value of 80.
D. The destination IP address of a packet will be the IP address of the network interface of the router.
Answer: A D
16 of 213
Huawei - H12-211
A configured internal host of a private network wishes to access the internet. What must be configured on the
enterprise network’s edge router in order to achieve this? (Choose two)
A. NAT EasyIP
B. DHCP
C. BGP
D. Default route
Answer: A D
Refer to the graphic. In order to improve security, the two hosts use IPsec VPN to transmit data. Which IPsec
mode and protocol can be used to hide the host’s IP address? (Choose two).
A. AH
B. transport mode
C. tunnel mode
D. ESP
Answer: C D
On Huawei switch, which of the following commands can be used to set port duplex mode as "auto
negotiation"? (Choose two)
B. duplex auto-negotiation
C. duplex auto
D. undo duplex
Answer: C D
17 of 213
Huawei - H12-211
According to OSI reference model, which layer is responsible for end to end error checking and flow control?
A. Physical layer
C. Network layer
D. Transport layer
Answer: D
An administrator connects two switches together in a local enterprise network. The ports of one switch support
Fast Ethernet, while the ports of the other switch support Gigabit Ethernet. Hosts connected to one switch are
able to communicate, however communication between the two switches fails. What is the possible reason for
this?
B. One port is supporting auto-negotiation, while auto-negotiation is disabled on the port of the other
switch.
C. The port of one switch is operating using half duplex mode, while the port of the other switch is using
full duplex mode.
D. A Fast Ethernet port cannot communicate directly with a Gigabit Ethernet port.
Answer: A
10.0.12.1 10.0.12.2 TCP 50190 > telnet [SYN] Seq=0 Win=8192 Len=0 MSS=1460
10.0.12.2 10.0.12.1 TCP telnet> 50190 [SYN, ACK] Seq=0 Ack=1 Win=8192 Len=0 MSS=1460
10.0.12.1 10.0.12.2 TCP 50190 > telnet [ACK] Seq=1 Ack=1 Win=8192 Len=0
Refer to the capture output.The administrator has captured three packets in the network. Which statement
regarding the capured packets is incorrect?
A.
18 of 213
Huawei - H12-211
Answer: B
Two end stations in a point-to-point network perform address resolution. Which of the following statements is
correct?
A. The destination address of an ARP request from each station will be a unicast MAC address.
B. The destination address of an ARP request from each station will be a broadcast IP address.
C. The destination address of an ARP reply from each station will be a unicast MAC address
D. The destination address of an ARP reply from each station will be a broadcast MAC address.
Answer: C
<Huawei>
Warning: Auto-Config is working. Before configuring the device, stop Auto-Config. If you perform
configurations when Auto-Config is running, the DHCP, routing, DNS, and VTY configurations will be lost.
Do you want to stop Auto-Config? [y/n]:
Refer to the output. When the administrator first starts the router, a system notice is displayed, however after
rebooting this router, the notice disappeared. What is the reason for this? (Choose two)
A. This notice only appears during the very first device startup.
B. The administrator has configured the device and saved the configuration, causing the notice to
disappear.
C. The administrator selected ‘n’ and did not save the configuration
Answer: B D
19 of 213
Huawei - H12-211
<Huawei>
Warning: Auto-Config is working. Before configuring the device, stop Auto-Config. If you perform
configurations when Auto-Config is running, the DHCP, routing, DNS, and VTY configurations will be lost.
Do you want to stop Auto-Config? [y/n]:
When an administrator first initializes the router, a warning is displayed. Which statement regarding this
warning is correct?
B. If Auto-Config is not required, the administrator should select ‘n’, for which subsequent configuration
of the
DHCP server, routing, DNS server and VTY user configuration is lost
C. When a device is started for the first time, the Auto-Config function is active.
D. When a device is started for the first time, the Auto-Config function is inactive.
Answer: C
FTP may be used to upgrade a router's VRP image. Which of the following transmission modes should be
used to achieve this?
A. binary mode
B. ASCII mode
C. byte mode
D. letter mode
Answer: A
B.
20 of 213
Huawei - H12-211
D. Only IP address
Answer: B
The network administrator has decided to configure link aggregation in the enterprise network. Which of the
following represent advantages of link aggregation? (Choose three)
A. Load balancing.
B. Improved bandwidth.
C. Enhanced reliability.
D. Improved security.
Answer: A B C
A user accesses a server supporting AAA, for which the authorization mode on the AAA server has been
configured using the command “authorization-mode hwtacacs if-authenticated”. Which of the following
statements regarding this command are true? (Choose three).
A. If the hwtacacs server fails to respond, the user will be authenticated using local authentication.
B. If the hwtacacs server fails to respond, the user will be authenticated using remote authentication.
C. If the hwtacacs server fails to respond, the user will bypass authentication.
Answer: A B D
Refer to the graphic. Two hosts communicate through a GRE tunnel. When the GRE tunnel is up, the network
administrator configures a static route on RTA to route packets to Host B. Which of the following commands
will achieve this?
A.
21 of 213
Huawei - H12-211
Answer: D
Refer to the display output. Which of the following statements regarding route shown are true? (Choose two)
A. The address 10.0.23.3 has been configured on the peer’s serial 2/0/0 interface.
C. The metric for the route 10.0.1.0 indicates that two hops are needed.
Answer: A D
The Eth-Trunk frame forwarding mechanism used to prevent changes in the data sequence forwards frames
based on which of the following parameters?
Answer: A B
[RTA]acl 2002
22 of 213
Huawei - H12-211
Refer to the configuration output. A network administrator configured the ACL on router RTA, as shown.
Which of the following statements regarding the rule order are correct? (Choose two).
Answer: B D
UDP is connectionless oriented, which of the following must be used in order to ensure reliability?
A. Internet Protocol
Answer: B
[RTA]aaa
[RTA-aaa]domain huawei
[RTA-aaa-domain-huawei]authentication-scheme au1
[RTA-aaa-domain-huawei]authentication-scheme au2
Refer to the configuration output. RTA has been configured using AAA as shown, and associated with the
“huawei” domain. For users in the huawei domain, which authentication-scheme will be used
A. au1
B. au2
23 of 213
Huawei - H12-211
C. au1 will be used. When au1 is deleted, users will use au2
D. au2 will be used. When au2 is deleted, users will use au1
Answer: B
Which of the following parameters must be specified when configuring static mapping for Frame Relay
network? (Choose two)
A. Local DLCI
B. Remote DLCI
Answer: A D
On the VRP platform, which of the following commands is used to configure the Router ID of a router as
1.1.1.1?
A. <Huawei>router id 1.1.1.1
B. [Huawei]router id 1.1.1.1
C. [Huawei]router-id 1.1.1.1
Answer: B
An Ethernet frame is captured by network protocol analyzer tool and the value of Type/Length field is 0x0800.
Which of the following statements about the frame are correct? (Choose two)
B.
24 of 213
Huawei - H12-211
Answer: A C
The administrator wishes to change name of the router. Under which view should the administrator be in order
to achieve this?
A. User-view
B. System-view
C. Interface-view
D. Protocol-view
Answer: B
Answer: A B C
Which of the following statements regarding static and dynamic routing is incorrect?
A. The static route can be easily configured and managed on the enterprise network.
B. The use of dynamic routing is more convenient for the administrator to manage the network following
network convergence.
25 of 213
Huawei - H12-211
C. The static route can automatically recover when a link failure is encountered.
Answer: C
A. OSPFv1
B. OSPFv2
C. OSPFv3
D. OSPFv4
Answer: C
With what kind of routers does a DRother router exchange link state information and route information?
(Choose two)
A. DR
B. BDR
C. DRother
Answer: A B
The network administrator wishes to transmit data between two end stations. The network interface cards of
both devices operates at 100Mbps however one supports half duplex while the other uses full duplex mode.
B.
26 of 213
Huawei - H12-211
B. The end stations can communicate, but data may be lost during transmission of large amounts of traffic.
D. The end stations can communicate, but speed is different during transmission of large amounts of traffic.
Answer: B
2 packet(s) transmitted
2 packet(s) received
A network administrator uses the ping command to test connectivity to the destination 10.0.0.2 on a Huawei
AR series router. Which statement regarding the output is correct?
Answer: A
In Layer 2 mode, the transmission rate of an Eth-Trunk interface is determined by which of the following?
C.
27 of 213
Huawei - H12-211
D. Number of interfaces.
Answer: A C
Refer to the graphic. The network administrator has configured ACL 2000 to filter packets on RTA, as shown.
Which of following statements regarding the subsequent behavior are correct? (Choose two).
Answer: B C
A. None
B. Local
C. Radius
D. 802.1X
Answer: A B C
An OSPF area is a collection of a group of routers and networks. OSPF defines that routers that have the same
( ) belong to the same OSPF area.
A. neighbors
B. LSDB
C.
28 of 213
Huawei - H12-211
C. LSA
D. adjacency
Answer: B
An administrator currently manages AR2200 devices in the network through a single password, however the
company wishes to introduce another two administrators and provide unique user credentials and privilege
levels for telnet access to the network devices. What action can be taken? (Choose three)
A. Configure three users under the AAA-view, and assign each a different password.
Answer: A B C
[RTA]acl 2001
Refer to the configuration output. Which of the following statements is correct regarding the configuration of
the ACL on RTA?
Answer: A
29 of 213
Huawei - H12-211
Which of the following formats represent an accurate condensing of the IPv6 address
2031:0000:720C:0000:0000:09E0:839A:130B? (Choose two).
A. 2031:0:720C:0:0:9E0:839A:130B
B. 2031:0:720C:0:0:9E:839A:130B
C. 2031::720C::9E0:839A:130B
D. 2031:0:720C::9E0:839A:130B
Answer: A D
Which of the following statements are correct about TTL field in IP packet? (Choose two)
<choice ident="A">
<choice ident="B">
<choice ident="C">
<choice ident="D">
B. Normally, it's impossible for a router to receive a packet whose TTL is zero.
C. The main purpose of TTL is to prevent IP packets from circulating endlessly in a network which can
consume a lot of bandwidth
D. TTL value will be decremented as a packet is passed through the network devices such as hub, LAN
switch and router.
Answer: B C
A web server in a private network is required to provide HTTP services to public users. The network
administrator is required to configure NAT on RTA. Which configuration should be used?
A. [RTA-Serial1/0/1]nat server protocol tcp global 202.10.10.1 www inside 192.168.1.1 8080
B. [RTA-Serial0/0/1]nat server protocol tcp global 192.168.1.1 www inside 202.10.10.1 8080
C. [RTA-Gigabitethernet0/0/1]nat server protocol tcp global 202.10.10.1 www inside 192.168.1.1 8080
30 of 213
Huawei - H12-211
D. [RTA- Gigabitethernet0/0/1]nat server protocol tcp global 192.168.1.1 www inside 202.10.10.1 8080
Answer: A
A layer 2 LAN switch generates CAM table entries according to the ( ) of the received frame.
C. Source IP address
D. Destination IP address
Answer: A
Which of the following statements regarding single area OSPF are correct? (Choose three)
A. An IP address needs to be configured on a loopback interface of each router before configuring an OSPF
area.
Answer: B C D
If Frame Relay implements dynamic address mapping for the PVC, which protocol will be used?
A. LMI protocol.
B. ARP protocol.
C. RARP protocol.
D. InARP protocol
31 of 213
Huawei - H12-211
Answer: D
An administrator discovered he/she was unable to use TFTP to transfer files to the router. Which of the
following describes the likely reason for this?
Answer: C
Which of the following commands is used to display the OSPF neighbor relationship establishment?
Answer: C
Answer: B
32 of 213
Huawei - H12-211
A. 6.
B. 8.
C. 10
D. 12.
Answer: B
NAPT allows for multiple internal addresses to be mapped to a single public address. How does NAT
distinguish between the different private addresses when mapping to the same public address?
Answer: C
Refer to the graphic. Two switches have been connected as shown and both support STP. The administrator
has configured switch A as a DHCP server and set interface VLANIF1 of switch B to obtain an IP address
from switch A. A link failure occurs on port interface G0/0/1 of switch B. What action will occur as a result?
Answer: C
33 of 213
Huawei - H12-211
To provide the information about the IP addresses that a user packet traverses along the path to the destination,
which of the following does Tracert record in each expired ICMP TTL packet?
A. Destination port
B. Source port
C. Destination address
D. Source address
Answer: D
If AH and ESP are both required to protect data streams between IPsec peers, how many Security Associations
(SA) are required in total?
A. 1
B. 2
C. 3
D. 4
Answer: D
On VRP platform, the command lines are classified into four levels in increasing priority: Visit level,
Monitoring level, Configuration level, and Management level. At which level, the operator is permitted to
configure service but is not permitted to operate the file system?
A. Visit level
B. Monitoring level
C. Configuration level
D. Management level
Answer: C
34 of 213
Huawei - H12-211
A. multiple areas
B. Router-ID
C. authentication
D. multicast updates
Answer: C
The administrator uses the ping command on the host to test connectivity to the website www.huawei.com.
The command line shows a request time out. The administrator displays the ARP entries for the host.
Which entry will be found in the ARP cache table of the host?
A. The MAC address of the destination www.huawei.com will exist in the ARP cache.
B. The MAC address of the switch will exist in the ARP cache.
C. The IP address of the destination www.huawei.com will exist in the ARP cache.
D. The MAC address of router interface G0/0/0, will exist in the ARP cache.
Answer: D
Host A has been connected to switch A and configured with an IP address. When Host A initially forwards a
frame, what action will be taken by Switch A?
B. Switch A will attempt to flood the frame to all ports except for the G0/0/1 interface.
C. Switch A will forward the frame via ports G0/0/1, G0/0/2 and G0/0/3.
D. Switch will receive this frame before returning the frame to G0/0/1.
35 of 213
Huawei - H12-211
Answer: B
The administrator cannot use telnet to manage the AR2200. The administrator is able to verify connectivity to
the router and has been informed that other administrators have no difficulties using telnet. Which statements
describe the possible reasons for this problem? (Choose two)
Answer: A C
Which of the following VRP commands can be used to enter area 0 view? (Choose two)
A. [Huawei]ospf area 0
B. [Huawei-ospf-1]area 0
C. [Huawei-ospf-1]area 0.0.0.0
D. [Huawei-ospf-1]area 0 enable
Answer: B C
What of the following statements is correct regarding access control list types and ranges?
Answer: C
36 of 213
Huawei - H12-211
Assume that the router has learnt the best route to the same destination by using RIP, OSPF and Static Route
respectively. By default, the Huawei router will select the route learnt via ( ) as the best route.
A. RIP
B. OSPF
C. RIPv2
D. Static route
Answer: B
Which of the following statements about a designated port working in RIPv2 multicast mode are true?
(Choose three)
Answer: A B C
Which of the following statements about the information contained in a Database Description packet are true?
(Choose three)
D. The header of an LSA is only a small portion of all the data of the LSA.
Answer: B C D
37 of 213
Huawei - H12-211
In the case of Huawei router, what is the "-i" parameter in a Ping command issued on a VRP operating system
used to set?
Answer: A
An authenticator router has been configured with two domains named “Area1” and “Area2”, following which
a user is created with the username “huawei” and the password ”hello” for authentication. Which domain does
this user belongs to?
<choice ident=“A”>
<choice ident=“B”>
<choice ident=“C”>
<choice ident=“D”>
A. Area1 domain
B. Area2 domain
C. default domain
D. default_admin domain
Answer: C
<Huawei>reset saved-configuration
Warning: The action will delete the saved configuration in the device.
38 of 213
Huawei - H12-211
Refer to the configuration output. Which of the following statements are true? (Select two answers)
A. A user should enter ‘Y’ when wishing to clear the saved configuration file.
B. The saved-configuration file that the device starts with can be erased.
Answer: A B
Which of the following statements regarding the DR in an OSPF network are correct? (Choose two)
B. A DR must be elected among the routers through the negotiations that are defined by OSPF protocol.
Answer: B D
The network administrator has configured the router as shown. Which statement is false?
A. The configuration manages the user login through the console interface.
B. The user login through vty 0 has the privilege to run level 2 commands.
C. The user login through telnet has the privilege to run level 2 commands.
Answer: A
OSPF allows for “multiple” processes. By default, OSPF selects a process whose number is ( ).
39 of 213
Huawei - H12-211
A. 0
B. 1
C. 10
D. 100
Answer: B
After checking the OSPF neighbor state, the administrator discovers that the router has established a
TWOWAY state with the peering router. What can be understood from this information? (Choose two)
Answer: D
When a router is powered on, the router reads the configuration file saved in the default save directory to get
itself initialized. If the configuration file does not exist in the default save directory, what does the router use
to initialize itself?
C. Default parameters
Answer: C
Two routers establish an IPsec tunnel, which of the following does not need to be the same on both peering
40 of 213
Huawei - H12-211
devices?
A. Encapsulation mode
B. Transform mode
C. Proposal name
D. authentication algorithm
Answer: C
An AR2200 router is required to be reconfigured from scratch. Which steps are needed to achieve this?
(Choose two)
Answer: A C
An administrator of a company supporting a large enterprise network wishes to implement OSPF on the
network as opposed to RIP. Which of the following points should the administrator use to support his
reasoning for this change? (Choose three)
Answer: A B D
41 of 213
Huawei - H12-211
Whilst configuring a device, an administrator experiences trouble remembering certain commands. Which of
the following will help support the administrator? (Choose two)
A. TAB
B. question mark
C. ctrl+b
D. ctrl+c
Answer: A B
A network administrator recently used tracert to trace the path to the destination IP address of an external
website, however the trace path displayed only a timeout result. Which of the following statements correctly
explains the reason for this? (Choose two)
Answer: B C
[RTA]acl 2001
Refer to the configuration output. Which of the following statements regarding ACL 2001 is correct?
42 of 213
Huawei - H12-211
Answer: B
Refer to the graphic. RTA and RTB have established an IPv6 network for which an IPv6 address has been
configured only on the G0/0/1 interface. RTA is unable to ping RTB. The administrator then configures v3
along with a router-id on both routers, and enables OSPFv3 on G0/0/1 of both RTA and RTB. Which of the
following statements are correct? (Choose two).
Answer: A D
Which of the following descriptions regarding IPv6 addresses are correct? (Choose two)
Answer: B C
On Huawei VRP platform, which of the following can be used to invoke the history command saved by the
command line interface? (Choose two)
<choice ident="A">
<choice ident="B">
<choice ident="C">
<choice ident="D">
43 of 213
Huawei - H12-211
C. Ctrl+P
D. Ctrl+U
Answer: A C
A server is linked to port interface G0/0/1 of a switch. The administrator wishes to allow only this server to be
linked to this interface on the switch. Which method can be used to achieve this?
A. Configure a static ARP entry using the server’s IP address and MAC address in the switch.
B. Configure a static MAC address binding entry of the server’s MAC address and the interface in the
switch.
C. Configure the default gateway of the switch to be the same as the server’s IP address.
Answer: B
The network administrator wants to improve the performance of network transmission, what steps can the
administrator take? (Choose two)
Answer: A B
Two routers are connected through serial interfaces and support PPP encapsulation. Which parameters must be
44 of 213
Huawei - H12-211
A. MRU
B. Authentication password
C. Magic-Number
D. IP address
Answer: A C D
D. eSight supports the backup of configuration files and network traffic analysis.
Answer: B
Which of the following descriptions regarding the TTL field of the IP packet is correct?
A. The TTL defines how many packets the source can send.
B. The TTL defines the duration during which the source can send packets.
C. The TTL value will decrement by 1 each time the packet is routed.
D. The TTL value will increment by 1 each time the packet is routed.
Answer: C
Refer to the graphic. The network administrator wishes to deny Host A access to the HTTP server but allow
access to all other servers. Which of the following ACL rules will achieve this?
45 of 213
Huawei - H12-211
Answer: B
An Ethernet port can work one of three duplex modes, whereas an Optical Ethernet port only supports one
single mode. Which of the following represents this mode?
A. Full-duplex
B. Half-duplex
C. Auto-negotiation
D. Simplex
Answer: A
What will the destination MAC address be at the moment a frame is transmitted by the host, when the router is
the IP destination?
Answer: D
<Huawei> system-view
46 of 213
Huawei - H12-211
[Huawei-ui-console0] quit
Refer to the configuration output. The administrator configured the device using the commands in the
configuration output. Regarding these commands, which statement is false?
C. A user that logs-in through the console interface is assigned the highest privilege level.
Answer: D
An administrator wishes to manage the router in the remote branch office, which method can be used?
A. Telnet
B. FTP
C. Console Connection
D. DHCP
Answer: A
Which of following may be the reasons that cause Frame Relay PVC to work abnormally? (Choose three)
47 of 213
Huawei - H12-211
Answer: B C D
Refer to the graphic. Which statements correctly explains the forwarding behavior between RTA and RTE?
(Choose two)
A. When the network uses OSPF, data will be forwarded along the path via S1/0/0
B. When the network uses RIPv2, data will be forwarded along the path via S1/0/0.
C. When the network uses OSPF, data will be forwarded along the path from via E0/0/1.
D. When the network uses RIPv2, data will be forwarded along the path via S2/0/0.
Answer: B C
The IP addresses of clients in the network are deployed via a DHCP server. When a host reboots, which
message will the host first send to the DHCP server?
A. DHCP DISCOVER
B. DHCP REQUEST
C. DHCP OFFER
D. DHCP ACK
Answer: B
A DHCP server has been established in the enterprise network. After the client has obtained an IP address
from the DHCP server, the user decided to modify the IP address manually. In what way may this affect the
enterprise network? (Choose two).
48 of 213
Huawei - H12-211
Answer: A B
Which of the following commands can be used to view the current configurations on a Huawei router?
A. display current-configuration
B. display saved-configuration
C. view saved-configuration
D. show startup-configuration
Answer: A
NAPT uses the same public address but different port numbers to translate private addresses. Which statement
regarding the port number is correct?
Answer: C
Answer: D
49 of 213
Huawei - H12-211
A router functioning as a Proxy receives an ARP request packet, but finds that the destination address in the
packet is not intended for itself. In this case, what will the router do? (Choose two)
C. Forward its MAC address to the ARP request sender after finding that a route to the destination address
is available.
Answer: B C
A. 30
B. 31
C. 32
D. 33
Answer: A
A. Neighbor discovery
Answer: A C
50 of 213
Huawei - H12-211
A client failed to transfer a file to the FTP server, but found the IP connectivity was without problem. The
client assumed that the problem was with the port configuration. The blocking of which ports would likely
cause this problem? (Choose two)
A. 21
B. 80
C. 20
D. 50649
Answer: A C
When using VRP, which of the following commands is used to configure the data link layer encapsulation
type of a serial interface as HDLC?
A. encapsulation hdlc
B. link-protocol hdlc
C. hdlc enable
D. link-protocol ppp
Answer: B
An administrator wishes to implement new features in the network, but the VRP version of one AR2200 router
is out of date. The administrator needs to upgrade the VRP software. Which of the following options regarding
file transfer is false?
A. The AR2200 router can function as a TFTP client to support the upgrade.
B. The AR2200 router can function as the TFTP server to support the upgrade.
C. The AR2200 router can function as the FTP server to support the upgrade.
D. The AR2200 router can function as an FTP client to support the upgrade.
Answer: B
51 of 213
Huawei - H12-211
A. source address
B. next hop
C. destination address
D. cost
Answer: A
Which of the following applications can be used to detect the path along which the data packets are
transmitted from the source to the destination?
<choice ident="A">
<choice ident="B">
<choice ident="C">
<choice ident="D">
A. Route
B. Netstat
C. Tracert
D. Send
Answer: C
52 of 213
Huawei - H12-211
Answer: C D
Interface G0/0/1 on RTA contains a MAC address of 00e0-fc03-aa73 and is configured with the IPv6 address
2001::2E0:FCFF:FE03:AA73. Which method is most likely to have been used to configure the interface IPv6
address?
A. DHCPv6
B. Auto-link
C. ARP
D. EUI-64
Answer: D
The network administrator wishes to forward data over an Eth-trunk, however associated member interfaces
operate at different rates. In terms of the resulting behavior, which of the following is true?
Answer: D
<Huawei> system-view
Refer to the command output. What is the result of the shown command?
A.
53 of 213
Huawei - H12-211
B. The command adjusts the save command in the user view to privilege level 3.
C. The command adjusts the user view command privilege level to 3, and saves the configuration.
D. The command adjusts the privilege level of a user to 3, and saves the configuration.
Answer: B
On VRP platform, which of the following parameters can be used together with the "ping" command to
specify the source address of an echo request message?
A. A
B. S
C. D
D. N
Answer: A
[RTA]acl 2001
Refer to the configuration output. Which of the following statements are correct regarding the configuration of
the ACL on RTA? (Choose two).
Answer: A D
54 of 213
Huawei - H12-211
In order to check if the interface serial 1/0/0 is working in either DCE or DTE mode, command ( ) is used.
B. display controller
D. display current-config
Answer: C
Refer to the graphic. The link between RTA and RTB is encapsulated using PPP. The IP addresses of serial
1/0/1 of RTA and serial 1/0/1 of RTB are in different network segments. Which following is correct? (Choose
two)
Answer: A D
A. Source interface
C. Protocol number
D. Time-range
Answer: A
55 of 213
Huawei - H12-211
Refer to the graphic. An administrator has configured OSPF on the two routers, following which he then
implements the command silent-interface s0/0/1 on RTA. What effect will this command have on the
network? (Choose two)
A. The link information advertised by RTB will be maintained in the Link State Database of RTA.
C. The configuration will not affect the OSPF neighbor relationship between the two routers.
D. The link information advertised by RTB will no longer be maintained in the Link State Database of
RTA.
Answer: B D
Which of the following mechanisms are used for flow control? (Choose three)
A. Acknowledgement
B. Buffering
D. Windowing
Answer: B C D
Which of the following commands can be used to display the routing table on a Quidway router?
A. display ip path
B. display ip routing-table
C. display interface
D. display current-configuration
Answer: B
56 of 213
Huawei - H12-211
Which of the following statements regarding the routing table are correct? (Choose two)
A. The next hop in the routing table is redundant because the outgoing interface can be used for packet
forwarding.
Answer: B D
Following a failure of services in the network, an administrator discovered that the configuration in one of the
enterprise routers had been changed. What actions can be taken by the administrator to prevent further
changes? (Choose three)
A. The administrator should limit access by setting the login privilege of users to 0.
B. The administrator should configure AAA to manage user authorization on the router.
C. The administrator should configure an ACL to allow only the administrator to manage the router.
Answer: A B C
Host A wishes to send data to host C, and generates an ARP request to obtain the destination MAC address.
D. The destination MAC address of this frame is the MAC address of G0/0/0 on RTA.
Answer: A
57 of 213
Huawei - H12-211
An end system is unable to communicate with a DHCP server following the startup process. Which IP address
may be used by the client?
A. 0.0.0.0
B. 127.0.0.1
C. 169.254.2.33
D. 255.255.255.255
Answer: C
Which of the following statements regarding Designated Routers in OSPF are correct? (Choose three)
B. If the priorities of two routers are different, the router with the lower priority will be elected as DR.
C. If the priorities of two routers are equal, the router with the higher Router ID will be elected as DR.
Answer: A C D
A DHCP Unique Identifier (DUID) in DHCPv6 can be configured in VRP using which formats? (Choose
two).
A. DUID-LL
B. DUID-LLT
C. DUID-EN
D. DUID-LLC
Answer: A B
58 of 213
Huawei - H12-211
In a small network suppporting IPv6, a network administrator wishes implement RIPng. Which of the
following commands should be used to enable this protocol?
A. [RTA-GigabitEthernet0/0/0]ripng 1 enable
B. [RTA]ripng 1 enable
C. <RTA>ripng 1 enable
D. [RTA-ripng-1]ripng 1 enable
Answer: A
A. IP
B. OSPF
C. BGP
D. IPX
Answer: A D
<Quidway>display mac-address
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
Refer to the graphic. A switch attempts to forward a frame to the MAC destination 5489-98ec-f01. What
operation will occur on the switch?
59 of 213
Huawei - H12-211
A. The switch will send a request to obtain the MAC address of 5489-98ec-f011.
B. The switch will report that the destination is unreachable and report this to the source.
C. The switch will flood the frame via all ports, with exception of the port on which the frame was
received.
D. The switch will drop the frame because it does not have an entry in its MAC address table.
Answer: C
Which of the following steps are necessary to configure OSPF on a Huawei router? (Choose three)
A. Configuration of a router ID
Answer: B C D
Answer: A
Refer to the graphic. Which of the following statements correctly describe the Frame Relay devices? (Choose
two)
A.
60 of 213
Huawei - H12-211
Answer: A C
Refer to the graphic. Host A is located in a private network. It is required that Host A not only be capable of
routing traffic over the public network, but also that public users are able to actively communicate with Host
A.
A. Static NAT
B. Dynamic NAT
C. Easy-IP
D. NAPT
Answer: A
Which of the following statements about collision domains and broadcast domains are correct? (Choose three)
Answer: A B D
61 of 213
Huawei - H12-211
Refer to the graphic. IPsec VPN uses ESP to encrypt which fields?
Answer: A
The network administrator attempts to add interface G0/0/1 on Switch A to Eth-trunk 1, however the
command fails. Which of the following may cause this?
Answer: C D
Refer to the graphic. The host has a problem establishing a telnet connection with the router attached to
interface G0/0/0. Which of the following steps can be used to help the administrator identify the problem?
(Choose two)
<choice ident=“A”>
<choice ident=“B”>
<choice ident=“C”>
<choice ident=“D”>
C. Use the ping tool to check connectivity between host and router.
62 of 213
Huawei - H12-211
Answer: C D
Refer to the graphic. In the private network, RTA dynamically assigns a public address from the address pool
to hosts without port translation. Host C wishes to access the public network while pool addresses are assigned
to Host A and Host B. What will occur as a result?
A. The first public address will be allocated to Host C, and Host A will be forced offline.
B. The last public address will be allocated to Host C, and Host B will be forced offline.
D. All hosts will have access to the public network through pool address swapping.
Answer: C
[Router-ip-pool-pool1] quit
[Router-ip-pool-pool2] quit
Refer to the configuration output. Following configuration, a host is connected to the interface Gigabit
Ethernet 0/0/1 of the router. Which IP address will the client obtain?
63 of 213
Huawei - H12-211
<choice ident=“A”>
<choice ident=“B”>
<choice ident=“C”>
<choice ident=“D”>
Answer: A
Which of the following must be used to establish the configuration environment when a router is powered on
for the first time?
A. SSL
B. SSH
C. Console port
D. Telnet
Answer: C
A router has learned two routes for the same network with the same prefix. One route has been learned via
OSPF with a metric of 4882, while the other route has been learned via RIPv2 with a metric of 4. Which route
(s) will be found in the routing table?
64 of 213
Huawei - H12-211
Answer: C
The IPv6 address achitecture does not include which of the following address types?
A. unicast
B. multicast
C. broadcast
D. anycast
Answer: C
Refer to the graphic. Packet encapsulation in the IPsec architecture is performed as shown. Which IPsec mode
is being used to encapsulate the packet?
A. normal mode
B. transport mode
C. tunnel mode
Answer: C
A network requires a solution to allow 50 private IP addresses to be translated, however only a single public
address is available for use. Which translation method can be used to support this requirement?
A. Static NAT
B. Dynamic NAT
C. Easy-IP
D. NAPT
Answer: C
65 of 213
Huawei - H12-211
In port aggregation, “multiple” ports are aggregated to form a port aggregation group so that all the member
ports in the group share the outgoing/incoming load. At which layer is port aggregation implemented?
A. Physical Layer
C. Network Layer
D. Transport Layer
Answer: B
When R2 forwards data to R3 from R1, which of the following items will change? (Choose two)
Answer: A B
Refer to the graphic. RTA and RTB have established a GRE tunnel, but only RTA has enabled the keepalive
function. When RTB receive a keepalive message from RTA, how will RTB respond?
B. RTB willl record receipt of the keepalive message but won’t reply
D. RTB will send a keepalive reply and begin to actively send keepalive messages.
Answer: C
66 of 213
Huawei - H12-211
Which of the following statements about router IDs are true? (Choose two)
A. The routers contained in the same LSDB have the same router ID.
C. Two routers in different OSPF areas can have the same router ID.
Answer: B D
A user logged into a VRP supported device through telnet, but when attempting to configure the device, found
that he is unable to use the sytem-view command to enter the system-view. What are the possible reasons for
this? (Choose two)
A. The device’s VTY interface only provides permission for some telnet users to run the sytem-view
command.
C. The user’s privilege level is lower than the level associated with the system-view command.
D. The system-view command privilege level is lower than the level associated with the user.
Answer: A C
Which of the following statements describes the network shown? (Choose two)
Answer: B C
67 of 213
Huawei - H12-211
Refer to the graphic. Which of the following statements is correct when this router forwards the packet to the
destination host 9.1.4.5?
A. The router selects the first entry to match the destination address of the packet because the preference of
OSPF is higher than the preference of RIP.
B. The router selects the second entry to match the destination address of the packet because the cost of
RIP is lower than that of OSPF.
C. The router selects the second entry to match the destination address of the packet because the outgoing
interface is an Ethernet interface. The forwarding speed of an Ethernet interface is faster than the
forwarding speed of a serial interface
D. The router selects the second entry to match the destination address of the packet because the router will
match the most specific address.
Answer: D
FTP and TFTP can be used to update the system file on Huawei routers. Which of the following statements are
correct? (Choose three)
<choice ident="A">
<choice ident="B">
<choice ident="C">
<choice ident="D">
Answer: A B C
68 of 213
Huawei - H12-211
Which of the following technologies can allow a host with IP address 10.0.0.1 to access the internet?
A. Static route
B. Dynamic route
C. Route import
D. NAT
Answer: D
Which of the following statements regarding link-state database and routing-table of a “single” OSPF area are
correct? (Choose two)
Answer: A C
Which of the following methods are supported by VRP platform to configure the router? (Choose three)
B. Through Telnet
D. Through FTP
Answer: A B C
69 of 213
Huawei - H12-211
The administrator wishes to manage a network through telnet from a user's terminal to a router. How can this
be achieved?
A. A connection should be established between the ethernet port of the terminal and the console port of the
router.
B. A connection should be established between the ethernet port of the terminal and the ethernet port of the
router.
C. A connection should be established between the console port of the terminal and the ethernet port of the
router.use console cable connect pc’s ethernet port and router’s console port.
D. A connection should be established between the COM port of the terminal and the console port of the
router.
Answer: B
While inspecting packets in the network, a network administrator discovers a frame with the destination MAC
address of 01-00-5E-A0-B1-C3. What can the administrator determine from this?
Answer: C
Which of the following parameter settings for terminal emulation are correct when configuring a Huawei
router through the Console port?
A. 4800bps, 8 data bits,1 stop bits, odd parity check, and no flow control
B. 9600bps, 8 data bits, 1 stop bits, no parity check, and no flow control
C. 9600bps, 8 data bits, 1 stop bits, even parity check, and hardware flow control
D. 19200bps, 8 data bits, 1 stop bits, no parity check, and no flow control
70 of 213
Huawei - H12-211
Answer: B
An administrator wishes to update the VRP software of company’s AR2200 router. How can this be achieved?
(Choose three)
A. The administrator can use FTP to transfer the VRP software, with the AR2200 router as the FTP client.
B. The administrator can use FTP to transfer the VRP software, with the AR2200 router as the FTP server.
C. The administrator can use TFTP to transfer the VRP software, with the AR2200 router as the TFTP
server.
D. The administrator can use TFTP to transfer the VRP software, with the AR2200 router as the TFTP
client.
Answer: A B D
Refer to the display output. What can be determined based on the output of the display command?
C. Interface Gigabit Ethernet 0/0/0 is not associated with a dynamically defined route.
D. Interface Gigabit Ethernet 0/0/0 has been manually shut down by an administrator.
Answer: D
Refer to the graphic. RTA is a DTE device connected to a Frame Relay switch, and uses dynamic address
mapping to establish the PVC. With regards to the configuration, which of the following commands are not
necessary? (Choose two).
A.
71 of 213
Huawei - H12-211
B. [RTA-Serial1/0/1]link-protocol FR
D. [RTA-Serial1/0/1]fr inarp
Answer: C D
Which of the following protocols is used in Frame Relay to map the address to DLCI dynamically?
<choice ident="A">
<choice ident="B">
<choice ident="C">
<choice ident="D">
A. ARP protocol
B. RARP protocol
C. InARP protocol
D. Map protocol
Answer: C
If Host B also configured the IP address as “192.168.1.1/24”, an IP address confict will occur. What will
happen as a result?
A. Host B will send an ICMP request to the destination with the configured IP address. If a reply is
received, the host will notify of an address conflict.
B. Host A will send a gratuitous ARP request to resolve the MAC address of the destination 192.168.1.1,
for which Host B will reply.
C. Host B will send a gratuitous ARP request to resolve the MAC address of the destination 192.168.1.1,
for which Host A will reply.
D. Host A will ignore any received ARP request intended for destination 192.168.1.1.
72 of 213
Huawei - H12-211
Answer: C
According to the default value of route preference on the VRP platform, which of the following represent the
correct sequence for direct route, static route, RIP and OSPF if they are listed from high preference to low
preference?
Answer: B
Refer to the graphic. RTA and RTB are connected to the same Frame Relay switch and use same DLCI
number, which following is correct? (Choose two).
Answer: B C
Which of the following statements regarding the router ID in OSPF are incorrect? (Choose three)
A. The router IDs of OSPF routers in the same area must be the same, but can be different in different
areas.
D.
73 of 213
Huawei - H12-211
Answer: A B C
74 of 213
Huawei - H12-211
If a company network administrator wants to be able to remotely manage branch network devices, which of
the following protocols will be used?
A. CIDR
B. RSTP
C. Telnet
D. VLSM
Answer: C
When a NAT uses a dynamic address pool, the addresses in the address pool can be reused, that is, the same IP
is mapped to multiple intranet IPs at the same time.
A. Correct
B. Error
Answer: B
Refer to the grapic. An administrator has configured RIPv2 on the two routers, following which he implements
the command silent-interface s0/0/1 on RTA. What effect will this command have on the network? (Two
Answers)
Answer: A D
75 of 213
Huawei - H12-211
The following configuration can be used to determine that the IP address of the GigabitEthernet0/0/0 interface
is incorrectly configured because the IP address of the interface is not
May end in 0.
[Huawei]interface GigabitEthernet0/0/0
A. Correct
B. Error
Answer: B
Both the alternate port and the backup port in RSTP cannot forward user traffic, but can receive, process, and
send BPDUs.
A. Correct
B. Error
Answer: B
<Huawei>system-view
[Huawei]user-interface console 0
[Huawei-ui-console0]authentication-mode password
[Huawei-ui-console0]quit
A. The administrator wants to log in and manage the device through the console port.
B. After the configuration is completed, the administrator cannot implement device management through
76 of 213
Huawei - H12-211
B.
remote login.
C. The user who logs in to the device through the console has the highest user privilege level.
D. The user password for logging in to the device through the console is cipher huawei2012.
Answer: D
A. SNMPv1
B. SNMPv2
C. SNMPv2c
D. SNMPv3
Answer: D
The Access port strips out the VLAN ID when it receives the same data frame with the same VLAN ID and
PVID. Then forward directly.
A. Correct
B. Error
Answer: B
In the PPP protocol, which of the following encryption algorithms is used by CHAP?
A. DES
B. MD5
C. AES
D. None
Answer: B
77 of 213
Huawei - H12-211
To establish multiple PPP point-to-point connections in the Ethernet network, a PPPoE server establishes
connections with multiple PPPoE clients on one Ethernet port. How does PPPoE differentiate between each
connection?
A. MAC address.
Answer: D
Which of the following protocols does the Frame Relay network use to dynamically map IP addresses to
DLCIs?
A. ARP protocol
B. RARP Agreement
C. InARP protocol
D. MAP protocol
Answer: C
When upgrading the router software using the FTP protocol, the transfer mode should be selected ().
A. Binary mode
C. Byte mode
D. Text mode
Answer: A
78 of 213
Huawei - H12-211
A company applies for a Class C IP address segment, but it is assigned to six subsidiaries. The largest
subsidiary has 26 computers. Different children
The company must be on a different network segment and the subnet mask should be set to (). A.
255.255.255.0
B. 255.255.255.128
C. 255.255.255.192
D. 255.255.255
.VRP supports OSPF multi-process. If no process number is specified, the default process number is ().
A. 0
B. 1
C. 10
D. 100
Answer: B
When the port of the Access type sends a message, it will ().
B. Strip the VLAN information of the message and then send it out.
C. Add the VLAN information of the packet, and then send it out.
D. Put the PVID information of this port and then send it out.
Answer: B
Refer to the graphic. RTA and RTB are running RIPv1. RTA has advertised 10.0.0.0 and 192.168.1.0 to the
79 of 213
Huawei - H12-211
RIP network. Which routes will exist in the IP routing table of RTB? (Choose two)
A. 10.0.0.0/8
B. 192.168.1.1/32
C. 10.1.12.1/32
D. 192.168.1.0/24
Answer: C D
A. Multi-regional division
B. Router-ID
C. Authentication function
Answer: C
A user can view the information for the RIP protocol on a router. What does “Age time” in the returned result
of the command mean?
Answer: B
The following is a mistake in the priority of static routes in Huawei devices (). A. The static router priority
value ranges from 0 255
80 of 213
Huawei - H12-211
C. The priority of static routes is divided into internal priority and external priority. Administrators can modify
external priority.
D. The priority value of the static route is 255, indicating that the route is unavailable.
How many ways does VRP support router configuration? (multiple choice)
Answer: A B C
PPP is more secure and reliable than HDLC because PPP supports (). (multiple choice)
A. PAP
B. MD5
C. CHAP
D. SSH
Answer: A C
The network structure and OSPF partition are shown in the figure. In addition to R1, routers R2, R3 and R4
are OSPF ABR routers.
81 of 213
Huawei - H12-211
A. Correct
B. Error
Answer: B
[Huawei]rip 1
[Huawei-rip-1]version 2
Refer to the command output. An administrator wishes to configure RIP. Which other command needs to
configured for RIP routes to be advertised?
82 of 213
Huawei - H12-211
D. network 192.168.1.0
Answer: D
Two routers have established a point-to-point network using PPP. The administrator has configured the routers
to run OSPF in the same area with the same router ID, what will behavior will occur as a result of the
configuration?
A. The routers will build a neighbor relationship even though both routers are using the same router ID.
C. The routers will build an adjacency even though both routers are using the same router ID.
D. The routers will not send hello packets to each other because they are using the same router ID.
Answer: B
The network administrator has captured a data frame in the network with a destination MAC address of
01-00-5E-A0-B1-C3. About the MAC address
Answer: C
A host in a private network needs to access the Internet. To achieve this requirement, the administrator should
83 of 213
Huawei - H12-211
A. NAT Easy IP
B. DHCP
C. STP
D. Default route
Answer: A D
In order to check whether the serial port S0/0/1 on the router is a DTE interface or a DCE interface, which of
the following commands should be used?
B. display saved-config
D. display current-config
Answer: C
Refer to the graphic. Two peering routers are running RIP. RTA is using RIPv1 to advertise its routes, while
RTB is using RIPv2 to advertise the route 1.1.1.1/32. How will the route 1.1.1.1/32 appear in the IP routing
table of RTA?
Answer: D
84 of 213
Huawei - H12-211
The two routers are connected through a serial port, and the serial link is encapsulated in PPP. Which of the
following parameters is required before the PPP link is Up?
A. MRU
B. Authentication Password
C. Magic-Number
D. Authentication Protocol
Answer: A C D
In the OSI reference model, the ability to perform end-to-end error detection and flow control is ().
A. Physical layer
C. Network layer
D. Transport layer
Answer: D
An access port can only send and receive untagged frames. When receiving a data frame with a tag, it will
directly discard it.
A. Correct
B. Error
Answer: B
As shown in the figure, the administrator configured the following command on the RTA, and the correct
85 of 213
Huawei - H12-211
[RTA-rip-1]silent-interface s0/0/1
Answer: A D
Network management hopes to effectively use the IP address of the 192.168.176.0/25 network segment. Now
that the company's marketing department has 20 hosts, it is best to allocate the following.
A. 192.168.176.0/25
B. 192.168.176.160/27
C. 192.168.176.48/29
D. 192.168.176.96/27
Answer: D
A. By sending a free ARP, you can confirm whether the IP address has a conflict.
86 of 213
Huawei - H12-211
B. The format of the free ARP packet is the same as that of the normal ARP request packet.
D. The format of the free ARP packet is the same as that of the normal ARP reply packet.
Answer: A B
In PPP, when the dual-end of both communicating parties detects the physical link activation, it will switch
from the link unavailable phase to the link establishment phase.
This phase is mainly through the negotiation of link parameters through the () protocol. A. IP
B. DHCP
C. LCP
D. NCP
The port in the Huawei device supports auto-negotiation technology. The following is true about the
negotiation result ().
A. The result of the negotiation under the 10 Gigabit electrical port must be full duplex.
B. The result of the negotiation under the 100M electrical port must be half duplex
D. When the duplex mode is inconsistent, you can solve it by replacing the network cable.
Answer: C
What are the three protocol components defined by PPP? (Choose three).
A. Data encapsulation.
B. LCP
C.
87 of 213
Huawei - H12-211
C. NCP
D. IPCP
Answer: A B C
Under the RIP process of the Huawei device, when the network 10.1.1.1/30 is announced, the following
configuration is correct (). (multiple choice)
A. network 10.1.1.0
E. network 10.0.0.0
Answer: C E
As shown in the figure, two hosts communicate between VLANs through one-arm routing. When the G0/0/1.2
sub-interface of RTA receives host B and sends it to host A.
Which of the following operations does RTA perform when data frames?
88 of 213
Huawei - H12-211
A. RTA forwards the data frame directly through the G0/0/1.1 subinterface.
B. After the RTA deletes the VLAN tag 20, it is sent out by the G0/0/1.1 interface.
C. RTA first deletes VLAN tag 20, then adds VLAN tag 10, and then sends it out through G0/0/1.1
interface.
Answer: C
The company network engineer has an AR2200 that cannot be started normally. How can the administrator
want to update its VRP?
A. The administrator needs to use the console cable to connect to the router and host, and then enter the
BootROM interface to complete the upgrade.
89 of 213
Huawei - H12-211
B. The administrator needs to configure the AR2200 as an FTP client and use FTP to transfer the new
VRP.
C. The administrator needs to configure the AR2200 to obtain an IP address through DHCP and then obtain
the VRP system file through TFTP.
D. The administrator needs to use telnet on the local host to remotely update the VRP system files of the
device.
Answer: B
Which of the following flow control methods can be used in the transport layer of the OSI reference model?
(multiple choice)
A. Confirmation technology
B. Cache technology
D. Window mechanism
Answer: B C D
IPsec VPN is used to transfer data between the two hosts. In order to hide the real IP address and ensure the
highest possible data, use IPsec.
A. AH
B. Transmission mode
C. Tunnel mode
D. ESPc
Answer: C D
After the host obtains the IP address from DHCP server A and restarts, what kind of message will the
90 of 213
Huawei - H12-211
A. DHCP DISCOVER
B. DHCP REQUEST
C. DHCP OFFER
D. DHCP ACK
Answer: B
The ACL configuration shown above is completed on the router RTA, and the following description is correct
().
[RTA]acl 2001
Huawei question bank battle report group: 434299778[RTA-acl-basic-2001]rule 20 permit source 20.1.1.0
0.0.0.255
A. The VRP system will automatically adjust the order of the first rule in the order of configuration.
B. The VRP system does not adjust the sequence number, but will first match the rule of the first
configuration. 20.1.1.0 0.0.0.255
C. Configuration error, the order number of the rule must be from small to large.
D. The VRP system will first match the second rule in order. deny source 20.1.1.0 0.0.0.255
Answer: D
There are two routers RTA and RTB between the source device and the destination device. Use the Tracert
command to check the path. When checking the first hop RTA, the source
The device sends a UDP packet with a TTL of 1 to a large port of the destination device. When the packet
reaches the RTB, the TTL becomes 0.
A. Time Exceeded
B. Echo Request
91 of 213
Huawei - H12-211
C. Echo Reply
D. Port Unreachable
Answer: A
The following description of the Router ID in OSPF is incorrect (). (multiple choice)
A. The router IDs must be the same in the same area. The router IDs in different areas can be different.
D. The prerequisite for the normal operation of OSPF is that the router has a router ID.
Answer: A B C
On the VRP platform, the order of the default protocol priorities of direct route, static route, RIP, and OSPF is
().
Answer: B
A. Static routing is simple to configure and easy to manage when applied in an enterprise.
B. After administrators deploy dynamic routing protocols in the enterprise network, post-maintenance and
expansion can be more convenient.
C. After a link fails, static routes can automatically complete network convergence.
92 of 213
Huawei - H12-211
D. Dynamic routing protocols take up more system resources than static routes
Answer: C
Regarding PPP configuration and deployment, the following statement is correct ().
Answer: B
D. Only IP address
Answer: B
A. IP
B. OSPF
C. BGP
D. IPX
Answer: B C
93 of 213
Huawei - H12-211
A. Enables the function of requesting for an IP address from the peer device.
B. Enables the function of accepting the request for an IP address from the remote device.
Answer: A
NAPT distinguishes the IP addresses of different users by the protocol number in TCP or UDP or IP packets.
A. Correct
B. Error
Answer: B
The ACL does not filter the traffic that the device itself generates to access other devices. It only filters the
forwarded traffic. The forwarded traffic includes other device access.
A. Correct
B. Error
Answer: A
B.
94 of 213
Huawei - H12-211
B. GVRP is a protocol that must be enabled on the switch, otherwise the switches cannot communicate
with each other.
C. GVRP is based on the GARP working mechanism and is used to maintain VLAN dynamic registration
information in the device and propagate the information to other devices.
Answer: C
When using VRP, which of the following commands is used to configure the PPP authentication method as
PAP?
A. ppp pap
B. ppp authentication-pap
D. ppp pap-authentication
Answer: C
Which of the following commands is used to display the current running state and configuration of RIP?
B. show rip
C. display rip
Answer: C
Which of the following fields in the packet shown will be encrypted by the ESP protocol of IPsec VPN?
95 of 213
Huawei - H12-211
Answer: A
On the switch, which VLANs can be deleted by using the undo command? (multiple choice)
A. VLAN 1
B. VLAN 2
C. VLAN 1024
D. VLAN 4094
Answer: B C D
The following two configuration commands can be used to implement the router backup and backup of the
router RTA to the same destination 10.1.1.0:
A. Correct
B. Error
Answer: B
96 of 213
Huawei - H12-211
B. The peer port connected to the port must be configured at the same time. port trunk permit vlan all
C. The connected peer device can dynamically determine which VLAN IDs are allowed to pass.
D. If the port default vlan 3 command is configured for the connected remote device, VLAN 3 between the
two devices cannot communicate.
Answer: A
As shown in the configuration, if the administrator configures OSPF on R1 but R1 cannot learn the routes of
other routers, the possible reason is ().
(multiple choice)
[R1]ospf
[R1-ospf-1]area 1
A. The area ID configured by this router is different from the area ID of its neighbor router.
B. The router is not configured with authentication, but the neighbor router is configured with
authentication.
D. This router does not announce the network connecting neighbors when configuring OSPF.
Answer: A B D
The network administrator configures the RIPng protocol on a small IPv6 network. Which of the following
configurations is correct and effective?
A. [RTA-GigabitEthernet0/0/0]ripng 1 enable
B. [RTA]ripng 1 enable
C. <RTA>ripng 1 enable
D.
97 of 213
Huawei - H12-211
D. [RTA-ripng-1]ripng 1 enable
Answer: A
Two routers are connected via serial interfaces and the link-protocol is PPP, but the MRU of two serial
interface’s are different, in PPP LCP negotiated stage, what will happen?
Answer: B
The ACL of the AR G3 series router supports two matching sequences: configuration order and automatic
sorting.
A. Correct
B. Error
Answer: A
A port in the discarding state of RSTP, although it will discard the received data frame, but it can receive it
according to the port.
A. Correct
B. Error
Answer: B
98 of 213
Huawei - H12-211
Refer to the graphic. Two peering routers are running RIP. RTA is using RIPv2 to advertise its routes, while
RTB is using RIPv1 to advertise the route 1.1.1.1/32. The administrator configures “RIP version 2 multicast”
for interface G0/0/1 of RTB. How will the route 1.1.1.1/32 appear in the the IP routing table of RTA?
Answer: D
When deploying an ACL on a Huawei device, the following description is correct (). (multiple choice)
A. Calling an ACL under an interface can only be applied to the exit direction.
C. ACLs can only define rules in the order of 10, 20, and 30.
D. ACLs cannot be used to filter OSPF traffic because OSPF traffic is not encapsulated using UDP
protocol
E. The ACL can match the TCP/UDP port number of the packet, and can specify the range of the port
number.
Answer: B E
The correct DD packet and LSA description for OSPF middle age is (). (multiple choice)
Answer: B C D
99 of 213
Huawei - H12-211
If the network address of a network is 10.1.1.0/30, then its broadcast address is ()?
A. 10.1.1.1
B. 10.1.1.2
C. 10.1.1.3
D. 10.1.1.4
Answer: C
Regarding the correspondence between the access control list number and the type, the following description
is correct ().
Answer: C
The STP switch sends BPDUs. The correct statement about BPDU is (). (multiple choice)
D. The destination MAC address of the BPDU frame is the broadcast address.
Answer: A C
100 of 213
Huawei - H12-211
Refer to the graphic. Two peering routers are running RIP. RTA is using RIPv1 to advertise its routes, while
RTB is using RIPv2. What effect will this have on learned routes?
A. RTA and RTB will both learn the routes advertised by RIP.
B. RTA will learn the RIP route advertised by RTB, however RTB is unable to learn the route advertised
by RTA.
C. RTB will learn the RIP route advertised by RTA, however RTA is unable to learn the route advertised
by RTB.
D. Neither RTA nor RTB are able to learn the RIP routes advertised by the peer.
Answer: B
When the route has a loop, which of the following problems may occur? (multiple choice 2)
Answer: B C
As shown in the figure, it can be judged that 00e0-fc99-9999 is the specific host MAC address learned by the
switch through ARP, and the host has been replaced by three.
Secondary IP address.
101 of 213
Huawei - H12-211
A. Correct
B. Error
Answer: B
Refer to the graphic. R1, R2 and R3 are running RIPv1. R1 and R3 both advertise 172.16.0.0 to the RIP
network. How will this affect R2?
D. R2 will have a route to both networks 172.16.1.0/24 and 172.16.2.0/24, but some packets for these
destinations will be lost.
Answer: D
As shown in the figure, the ports connected to the host by SWA and SWB are both Access ports and the PVID
is 2. G0/0/1 of SWA is a Hybrid port.
The PVID is 1, and the port hybird tagged vlan 2 command is configured. G0/0/1 of the SWB is a trunk port,
the PVID is 1, and VLAN 2 is allowed.
102 of 213
Huawei - H12-211
A. Host A can send a data frame to Host B but cannot receive a reply from Host B.
B. Host A cannot send data frames to Host B but can receive data frames sent by Host B.
Answer: D
Which routing subnets 10.0.0.24/29 may be aggregated by the following subnet routes? (multiple choice)
A. 10.0.0.24/30
B. 10.0.0.23/30
C. 10.0.0.26/30
D. 10.0.0.28/30
Answer: A D
A. system-view
B. router
C. quit
D. user-view
Answer: C
B.
103 of 213
Huawei - H12-211
Answer: A B C
The PPPoE session establishment process can be divided into which stages? (Choose two).
A. Discovery stage
B. DHCP stage
Answer: A C
The following is true about the TTL field in the IP packet header ().
A. TTL defines the number of packets that the source host can send.
B. TTL defines the time interval at which the source host can send packets.
C. Whenever a packet passes through a router, its TTL value will be decremented by one.
D. Whenever a packet passes through a router, its TTL value will be increased by one.
Answer: C
Which of the following types of addresses are not included in the Pv6 address?
A. Unicast address
B. Multicast address
C.
104 of 213
Huawei - H12-211
C. Broadcast address
D. Anycast address
Answer: C
NAPT allows multiple private IP addresses to be mapped to the same public IP address through different port
numbers. The following information about the port number in NAPT
A. You must manually configure the mapping between port numbers and private addresses.
Answer: C
As shown in the figure, the network administrator wants to manually aggregate the two physical links between
the SWA and the SWB into an Eth-Trunk link.
D. Cannot be aggregated
105 of 213
Huawei - H12-211
Answer: D
As shown in the figure, regarding the frame relay device, the following description is correct (). (multiple
choice)
Answer: A C
[RTA]acl 2002
Which of the following entries will be matched on the router PTA using the ACL matching routing entries
shown above? (multiple choice)
A. 172.16.1.1/32
B. 172.16.1.0/24
C. 192.17.0.0/24
D. 172.18.0.0/16
Answer: A D
As shown in the figure, all four switches run STP, and various parameters use default values. It is blocked on
the G0/0/2 port of the root switch C.
When a configuration BPDU is sent through this port, how long will the blocked port in the network enter the
forwarding state?
106 of 213
Huawei - H12-211
A. About 30 seconds
B. About 50 seconds
C. About 15 seconds
D. About 3 seconds
Answer: B
The following description of the OSPF area is correct (). (multiple choice)
A.
107 of 213
Huawei - H12-211
A. Configure the ip address of the loopback interface of the router before configuring the OSPF area.
Answer: B C
As shown in the figure, if the command ping 10.1.1.2 is executed on R1, LSW1 receives the data frame from
VLAN 10 of LSW2.
Signed.
108 of 213
Huawei - H12-211
A. Correct
B. Error
Answer: A
The Ethernet electrical interface can work in 3 duplex modes, and the Ethernet optical interface can only work
in () mode.
A. Full duplex
B. Half duplex
C.
109 of 213
Huawei - H12-211
C. Auto-negotiation
D. Simplex
Answer: A
Which command can be used to check the PPPoE client session status?
B. display current-configuration
Answer: D
In order to change some office locations frequently, network administrators often plan to access users from
different switches to the corporate network.
A. Port-based VLAN
Answer: C
A. ICMP messages can record time, including original time, receiving time, and sending time.
B. ICMP packets are encapsulated in IP packets without being encapsulated in the transport layer.
C. ICMP packets protect ICMP error packets, control packets, request/response packets, and refresh
110 of 213
Huawei - H12-211
C.
packets.
Answer: B C
As shown in the figure, according to the configuration on the router R1, it can be judged that the two PCs can
access the ISP network normally.
A. Correct
111 of 213
Huawei - H12-211
B. Error
Answer: A
The company has users who report that when using the network to transfer files, the speed is very low. The
administrator found a packet in the network using Wireshark software to capture packets.
Some duplicate frames, the following description of the possible causes or solutions is correct ().
A. When the switch cannot find the destination MAC address of the data frame in the MAC address table,
the switch will flood the data frame.
Answer: C
Which of the following parameters cannot be used for the advanced access control list?
A. Physical interface
C. Agreement number
D. Time range
Answer: A
As shown in the figure, the R0 and RTB G0/0/1 interfaces are configured with IPV6 addresses of different
network prefixes, and the network administrator is on two routers.
Both run the OSPFv3 protocol and configure the OSPFv3 Router ID for each router. The correct description is
(). (many selected)
112 of 213
Huawei - H12-211
Answer: A C
When the router is powered on, the configuration file is read from the default storage path for initialization of
the router. If there is no default storage path
A. New configuration
B. Initial configuration
C. Default configuration
D. Current configuration
Answer: C
In the command fr map ip 10.1.1.2 200, the meaning of the number 200 is ().
113 of 213
Huawei - H12-211
Answer: B
On the Huawei AR G3 router, the -i parameter of the Ping command in the VRP is used to set ()
Answer: A
The ARP protocol can resolve the MAC address of the target device according to the destination IP address, so
as to map the link layer address and the IP address.
A. Correct
B. Error
Answer: A
As shown in the topology and the configuration on the switch interconnect port, you can determine that the
data frame labeled as VLAN 10 can be between the two switches.
Normal forwarding.
114 of 213
Huawei - H12-211
A. Correct
B. Error
Answer: B
If the administrator wants to update the VRP of the AR2200 router, the correct method is (). (multiple choice)
A. The administrator configures the AR2200 as an FTP client to transfer VRP software through FTP.
B. The administrator configures the AR2200 as an FTP server to transmit VRP software through FTP.
C. The administrator configures the AR2200 as a TFTP server and transmits VRP software through TFTP.
115 of 213
Huawei - H12-211
D. The administrator configures the AR2200 as a TFTP client to transmit VRP software through TFTP.
Answer: A B D
On a multi-access network such as Ethernet, the PPPoE server can establish PPP with many PPPoE clients
through an Ethernet port.
Connection, so the server must establish a unique session identifier for each PPP session to distinguish
between different connections. What parameters will PPPoE use?
A. MAC address
Answer: D
When STP is running on Huawei Sx7 series switches, the priority of the switch is () by default.
A. 4096
B. 8192
C. 16384
D. 32768
Answer: D
Huawei AR G3 series routers can update system files through FTP and TFTP. The following description is
correct () (multiple choice)
B.
116 of 213
Huawei - H12-211
Answer: A B C
<Huawei>reset saved-configuration
Warning:The action will delete the save configuration in the device.The configuration will be erased to
reconfigure.Continue?[Y/N]:
The administrator performs the following configuration on the AR2200. The following description about the
configuration information is correct ().
A. If the user wants to clear the saved configuration file, he should choose Y.
B. The configuration file will be retained when the device starts up.
C. If the user wants to clear the saved configuration file, he should choose N
D. The saved configuration file will be replaced by the running configuration file.
Answer: A
Referring to the following topology and configuration, routers R1 and R2 are connected through a Serial
low-speed cable, and the data link layer uses PPP. When R1 and R2
When the Holdtimes are inconsistent, ARP negotiation fails and communication cannot be performed.
117 of 213
Huawei - H12-211
A. Correct
B. Error
Answer: B
Answer: B
118 of 213
Huawei - H12-211
A. Source address
B. Next hop
C. Target network
D. Routing cost
Answer: A
C. If the cost of the route is larger, the priority of the route is higher.
D. In VRP, the greater the priority of the routing protocol, the higher the priority of the route.
Answer: C D
When configuring the PPP authentication method as PAP, which of the following operations are necessary?
(Choose three)
A. Add the user name and password of the authenticated party to the local user list
B. Configure the encapsulation type of the interface connected to the peer as PPP.
D. On the authenticated party end, configure the user name and password that are sent to authenticator
Answer: A B D
When using the Tracert program to test the path through which the target node passes, the default is to count ()
times for each Traceroute.
A.
119 of 213
Huawei - H12-211
A. 3
B. 4
C. 6
D. 8
Answer: A
A. For the physical layer, PPP supports asynchronous links and synchronous links.
D. PPP supports multiple network layer protocols, such as IPCP and IPXCP.
E. PPP supports bundling multiple physical links into logical links to increase bandwidth
Answer: A C D E
The authentication scheme, authorization scheme, accounting scheme, HWTACACS, or RADIUS server
template created on the AR router.
A. Correct
B. Error
Answer: A
When the specified interface is running in RIPv2 multicast mode, the following statement is correct ().
(multiple choice)
120 of 213
Huawei - H12-211
Answer: A B
In a frame relay network, DLCI is only the identifier of a virtual circuit under an interface. It must be globally
unique when planning and deploying.
A. Correct
B. Error
Answer: B
Refer to the graphic. An administrator has configed RIPv2 in the two routers shows in the figure. What will
happen after configuring the following commands? (Choose two)
[RTA-Serial0/0/1]rip output
[RTA-rip-1]silent-interface s0/0/1
Answer: A D
As shown in the figure, after the switch SWA is running RSTP, the administrator configures the port of the
G0/0/3 of the SWA as an Edge Port and uses one switch.
The machine replaces the host C, and the correct description below is ().
121 of 213
Huawei - H12-211
A. The G0/0/3 port of SWA will be closed after receiving the BPDU sent by the switch.
B. The G0/0/3 port of SWA will discard the received BPDU and forward the data normally.
C. The G0/0/3 port of SWA will perform RSTP operation after receiving the BPDU.
D. Among all hosts, only host A can send and receive data normally.
Answer: C
As shown in the figure, a static NAT command is deployed on router R1. When the PC accesses the Internet,
the destination address in the packet does not occur.
Any changes.
122 of 213
Huawei - H12-211
A. Correct
B. Error
Answer: A
The necessary technology to enable a host with an IP address of 10.0.0.1 to access the Internet is ().
A. Static routing
B. Dynamic routing
C. Route introduction
D. NAT
Answer: D
The following description about the trunk port and the access port is correct ().
A.
123 of 213
Huawei - H12-211
Answer: A
Answer: C
When a router forwards a packet, if it does not match the corresponding detail route and there is no default
route, the router will discard the packet directly.
A. Correct
B. Error
Answer: A
Two authentication domains "Area1" and "Area2" are configured on the authentication server. If the user uses
the correct username "huawei" and the password is used.
The code "hello" is authenticated, and which authentication domain is this user assigned to?
C.
124 of 213
Huawei - H12-211
Answer: C
Regarding the RIP routing protocol, the following description is correct ().
A. The router cannot send a router entry with a hop count of 16 to its directly connected neighbor.
B. The router may receive a route entry with a hop count of 16 sent by the directly connected neighbor, but
will discard it immediately after receiving it, and will not do any other processing.
C. The router may receive a route entry with a hop count of 16 sent by the directly connected neighbor.
After receiving it, it will use it to update its own routing table.
Answer: C
The following statement about the working mode of the Ethernet port is correct? (multiple choice)
C. The Ethernet port mode works normally when it does not match.
E. 100M Ethernet port working mode supports full duplex and half duplex
Answer: D E
A. Correct
B. Error
125 of 213
Huawei - H12-211
Answer: B
<R2>debugging rip 1
Sep 13 2013 11:07:20.974.2-05:13 R2 RIP/7/DBG: 6: 13465: RIP 1: Receive response from 10.0.12.1 on
GigabitEthernet0/0/0
Sep 13 2013 11:07:20.974.3-05:13 R2 RIP/7/DBG: 6: 13476: Packet: Version 1, Cmd response, Length 24
Sep 13 2013 11:07:20.974.5-05:13 R2 RIP/7/DBG: 6: 2688: RIP 1: Ignoring packet. This version is not
configured.
Refer to the debug output. Following configuration of R2, the administrator discovers that the behavior is not
as expected and performs debugging. Based on the output from the debug, what is the source of the problem?
Answer: D
Answer: A C D
126 of 213
Huawei - H12-211
Answer: D
When both ends running PPP protocol detect that the physical link is active, the link state will transit from
dead to establish. Which of the following protocols is used to negotiate the link parameters during this phase?
A. IP
B. DHCP
C. LCP
D. NCP
Answer: C
As shown in the figure, the administrator wants to improve the performance of this network. Which of the
following is most appropriate?
127 of 213
Huawei - H12-211
A. Connect each host with a switch and change the working mode of each host to full duplex.
B. Connect each host with a switch and change the working mode of each host to half duplex
C. Connect each host with the HUB and change the working mode of each host to full duplex.
D. Connect each host with the HUB and change the working mode of each host to half duplex.
Answer: A
B. It is necessary to make certain modifications to the three-layer header of the forwarded message, and
then forward it.
128 of 213
Huawei - H12-211
Answer: B
Huawei devices can be managed using the Telnet protocol. Which of the following statements is correct about
this management function?
A. The default port number used by Telnet is 22, which cannot be modified.
Answer: B
Which of the following WLAN standard operating frequencies are in the 5 GHz band? (multiple choice)
A. 802.11a
B. 802.11b
C. 802.11g
D. 802.11n
Answer: A D
You can use the preference preference to configure the priority value of a RIP route or the command in the
RIP process of the Huawei device.
After specifying a routing policy, set the priority value for the specific route that meets the conditions.
A. Correct
B. Error
Answer: A
129 of 213
Huawei - H12-211
The following is a description of the Forwarding state description error in the spanning tree protocol ().
B. Forwarding state port does not learn the source MAC address of the packet.
Answer: B
The main function of .InARP is to solve the protocol address of the peer device connected to each virtual link,
including IP address and IPX address.
A. Correct
B. Error
Answer: A
As shown in the figure, STP is disabled on both switches. Host A sends an ARP Request, and the following
description is correct ().
(multiple choice)
130 of 213
Huawei - H12-211
C. The MAC address table of the two switches will frequently jitter
131 of 213
Huawei - H12-211
Answer: B C D
You can use the undo summary command to disable automatic summarization of the routing protocol RIPv2 in
Huawei devices.
A. Correct
B. Error
Answer: A
In the frame relay network, regarding the mapping information on the DTE device, the description is correct ()
Answer: A
You can use the vlan batch command to create multiple VLANs in batches on the Huawei switch to simplify
the configuration process.
A. Correct
B. Error
Answer: A
A. DES
B. MD5
132 of 213
Huawei - H12-211
C. AES
Answer: B
Two routers are connected via serial interfaces, for which the link-protocol is PPP. The network administrator
wishes to configure PPP authentication to improve security on this link. Which PPP authentication method
provides a more secure solution?
A. CHAP
B. PAP
C. MD5
D. SSH
Answer: A
In the RSTP standard, the port that the switch directly connects to the terminal instead of the other bridge is
defined as ().
A. Fast port
B. Backup port
C. Root port
D. Edge port
Answer: D
What are the following characteristics of the default VLAN in a Layer 2 Ethernet switch? (multiple choice)
C.
133 of 213
Huawei - H12-211
C. You must create a default VLAN before you can assign a port to it.
D. The IP address configured on the switch will only be applied to the member port of the default VLAN.
Answer: A B
Refer to the following DHCP flowchart, the following statement is correct (). (multiple choice)
E.
134 of 213
Huawei - H12-211
Answer: B C D
As shown in the figure, the host has established a connection with the router through Telnet. For the data sent
by the host to the router, the following description is positive.
The destination MAC address of the data frame sent by the host is the MAC address of the interface G0/0/0 of
the router.
B. The destination MAC address of the data frame sent by the host is the MAC address of the switch.
C. The destination port number in the data segment sent by the host is 80.
D. The destination IP address of the packet sent by the host is the IP address of the interface G0/0/0 of the
router.
A, D
In the STP protocol, assume that all switches have the same priority, and the MAC address of switch 1 is
00-e0-fc-00-00-40, switch 2
The MAC address of the switch is 00-e0-fc-00-00-10, the MAC address of switch 3 is 00-e0-fc-00-00-20, and
the MAC address of switch 4 is 00-e0-fc-
135 of 213
Huawei - H12-211
A. Switch 1
B. Switch 2
C. Switch 3
D. Switch 4
Answer: B
As shown in the figure, after the network administrator finishes Telnet configuration on the router, it finds that
the host cannot establish a connection with the router through Telnet.
C. Use ping to check the IP connectivity between the host and router G0/0/0 interface
Answer: C D
In the network as shown, the following description is correct (). (multiple choice)
136 of 213
Huawei - H12-211
Answer: C D
The login timeout time in the VRP system needs to be configured on the VTY interface.
A. Correct
B. Error
Answer: A
137 of 213
Huawei - H12-211
As shown in the figure, the configuration of the VLAN on the Huawei switch is correct (). (multiple choice)
A. Client1 belongs to VLAN 10, and the commands for VLAN division on the switch are correct.
B. Client2 belongs to VLAN 20, and the VLAN-based command on the switch is correct.
C. Client3 belongs to VLAN 30, and the commands for VLAN division on the switch are correct.
D. Client4 belongs to VLAN 40, and the commands for VLAN division on the switch are correct.
E. Client4 is not in VLAN 40, and the command to divide the VLAN on the switch is incorrect.
Answer: A B E
138 of 213
Huawei - H12-211
When the administrator configures the DHCP server, which of the following commands configures the lease
time to be the shortest?
Ip pool pool1
Gateway-list 10.10.10.1
A. dhcp select
B. lease day 1
C. lease 24
D. lease 0
Answer: B
After the GRE keepalive function is enabled, the local end of the GRE tunnel periodically sends a keepalive
packet to the peer every 10 s.
A. Correct
B. Error
Answer: B
After a command for displaying RIP route information is entered on a router, peer 192.168.1.2 on Serial1/0/0
is displayed in the returned result. What does 192.168.1.2 stand for?
Answer: A
139 of 213
Huawei - H12-211
In the OSPF protocol, what are the correct ones for the description of DR? (multiple choice)
A. By default, all routers in this broadcast network will jointly vote with DR.
B. If the priority values of the two routers are different, select the router with the smaller priority value as
the DR.
C. If the priority values of the two routers are equal, select the router with the large router ID as the DR.
Answer: A C D
The above is the display startup information of the AR2200 router. For this information, the error is ().
C.
140 of 213
Huawei - H12-211
C. The system file cannot be modified when the device starts next time.
D. The system file of the next startup of the device can be modified by using the command "startup system
software<startup-software-name>.cc".
Answer: C
The configuration of Vty is as shown above, and the user privilege level is set to level 3, which is also the
highest level that can be set.
A. Correct
B. Error
Answer: B
The network topology is as shown in the figure. The cost of all links in the network is the default value. When
the RTA forwards the packet to the RTE, about routing.
141 of 213
Huawei - H12-211
A. If the routers in the network are running OSPF, the RTA will use the S1/0/0 interface to forward data to
the RTE.
B. If the routers in the network are running RIPv2, the RTA will use the S1/0/0 interface to forward data to
the RTE.
C. If the routers in the network are running OSPF, the RTA will use the E0/0/1 interface to forward data to
the RTE.
D. If the routers in the network are running RIPv2, the RTA will use the S2/0/0 interface to forward data to
the RTE.
Answer: B C
142 of 213
Huawei - H12-211
The network administrator uses the ping command on the AR G3 series router to test connectivity to 10.0.0.2.
The following description of the output is correct.
Yes().
2 packet(s) transmitted
2 packet(s) received
Answer: A
The network administrator created VLAN 10 on the Layer 3 switch and configured the IP address on the
virtual interface of the VLAN. When using life
After the display ip interface brief is displayed, the interface of VLANIF 10 is down.
D. Add a port that must be UP and must be a trunk type into VLAN 10.
143 of 213
Huawei - H12-211
Answer: C
The packet capture tool captures an Ethernet frame and finds that the value of the Type/Length field of the
frame is 0x0800. The following description of the frame is correct.
A, C
Regarding the commands used to detect IP network connectivity, the following statements are incorrect ().
(multiple choice)
A. ping 127.0.0.1, this command is used to check whether the network cable of the host is plugged in.
B. ping 127.0.0.2, this command is used to check whether the host's network cable is plugged in.
C. The ping command can be used to detect the connectivity of the host to the local gateway.
D. The ipconfig/release command can be used to detect the connectivity of the host to the local gateway.
Answer: A B D
A trunk port can send both tagged data frames and unlabeled data frames.
A. Correct
B. Error
Answer: A
As shown in the figure, the correct description about this network topology is ().
144 of 213
Huawei - H12-211
Answer: B
145 of 213
Huawei - H12-211
As shown in the figure, the network administrator creates VLAN 2 on the SWA and SWB, and configures the
ports connected to the host on the two switches as access terminals.
Port, into VLAN 2. Configure G0/0/1 of SWA and G0/0/2 of SWB as trunk ports to allow all VLANs to pass.
Then we have to implement two
B. Configure G0/0/1 on the SWC as the trunk port and allow VLAN 2 to pass.
C. Configure G0/0/1 and G0/0/2 on the SWC as trunk ports and allow VLAN 2 to pass.
D. Create VLAN 2 on the SWC, configure G0/0/1 and G0/0/2 as trunk ports, and allow VLAN 2 to pass.
Answer: D
In standard STP mode, which of the following non-root bridge switches forwards the TC set by the root switch
to BPUD?
A. Root port
B. Backup port
C. Designated port
D. Provisioning port
Answer: C
146 of 213
Huawei - H12-211
Which of the following statements about a designated port working in RIPv2 multicast mode are true?
(Choose three)
Answer: A B C
The CHAP authentication command enabled in .PPP is: ppp chap authentication.
A. Correct
B. Error
Answer: B
As shown in the figure, all three switches run GVRP, create VLAN 10 and VLAN 20 on SWA and SWC, and
create them on SWB.
VLAN 10. SWB dynamically learned VLAN 20 from SWA and SWC through GVRP. If the port G0/0/1 on
the SWB is modified to be GVRP
147 of 213
Huawei - H12-211
Answer: A
The administrator finds that the two routers stay in the TWO-WAY state when establishing an OSPF neighbor.
The correct description is ().
Answer: D
A.
148 of 213
Huawei - H12-211
A. OSPFv1
B. OSPFv2
C. OSPFv3
D. OSPFv4
Answer: C
A. Correct
B. Error
Answer: B
A RIP router receives the routing update information from its neighbor. Which of the following statements
regarding routing update are correct? (Choose three)
A. The received route that is not in the routing table will be added only when its hop count value is less
than 16.
B. The received route that already exists in the routing table will be updated only when the next hop is the
router's neighbor and the cost value is smaller.
C. The received route that already exists in the routing table will be updated only when the next hop is not
the router's neighbor and the cost value is smaller.
D. The received route that already exists in the routing table will be updated only when the next hop is the
router's neighbor and the cost value has been changed.
Answer: A C D
There is a TTL field in the header of the IP packet. The correct statement about this field is ()
149 of 213
Huawei - H12-211
Answer: C
A switch receives a data frame with a VLAN tag, but finds that the MAC address of the data frame cannot be
queried in its MAC address table.
Then the processing behavior of the data frame by the switch is ().
B. The switch broadcasts this data frame to all ports (except the receiving port) in the VLAN that belongs
to the data frame.
Answer: B
[RTA]aaa
[RTA-aaa]domain huawei
[RTA-aaa-domain-huawei]authentication-scheme au1
[RTA-aaa-domain-huawei]authentication-scheme au2
The network administrator performs the above configuration on the Huawei router RTA. If a user needs to be
authenticated in the authentication domain "huawei", the following is true.
C. will use the "authentication-scheme au1" certification, if "au1" is deleted, will use "au2"
D. will use the "authentication-scheme au2" certification, if "au2" is deleted, will use "au1
150 of 213
Huawei - H12-211
Answer: B
Refer to the graphic. RTA is a PPPoE client, and following transmission of PADI, Server A responds with
PADO packets to RTA. Which distribution method is used for sending PADO packets?
A. unicast
B. multicast
C. broadcast
D. anycast
Answer: A
The two routers are running on the PPP link. The administrator has configured OSPF single areas on both
routers, and their router IDs are the same.
B. VRP will prompt the router ID conflicts between the two routers.
Answer: B
Refer to the graphic. RTA is a PPPoE client, and sends PADI packets to Server A. Which distribution method
is used for sending PADI packets?
A. unicast
B. multicast
C. broadcast
D.
151 of 213
Huawei - H12-211
D. anycast
Answer: C
Which of the following parameters should be considered when electing a root port in STP? (multiple choice)
B. Port priority
Answer: A B C
In Huawei devices, which method can OSPF elect the router ID? (multiple choice)
A. If a loopback interface is configured, select the largest IP address from the IP address of the loopback
interface as the router ID.
B. If the loopback interface is not configured, select the largest IP address as the router ID among the IP
addresses of other interfaces.
C. Huawei switch may use the largest VLANIF IP address as the router ID.
Answer: A B C E
As shown in the figure, regarding the topology and configuration of OSPF, the correct statement in the
following statement is ()
152 of 213
Huawei - H12-211
B. R1 and R2 can establish stable neighbor relationships as long as the interface network type of R1 is
restored to the default broadcast type.
C. As long as the interface network type of R1 is restored to the default broadcast type, and the hello time
is adjusted to 10s, R1 and R2 can be established.
Neighbor relationship
D. R1 Compared with R2, R2 has a better chance of becoming a DR because its interface DR priority value
is relatively small.
Answer: C
153 of 213
Huawei - H12-211
The Tracert Diagnostic Tool in Huawei routers uses UDP to encapsulate trace data.
A. Correct
B. Error
Answer: A
The MAC address of G0/0/1 on a router is 00E0-FC03-AA73. The IP address of this interface is
2001::2E0:FCFF:AA73, root.
Based on this information, it can be determined that the interface identifier of this interface is based on ().
A. DHCPv6
B. Auto-link
C. ARP
D. EUI-64
Answer: D
If PPP authentication fails, which type of packet will be sent to the authenticated peer by the authenticator?
A. Authenticate-Ack
B. Authenticate-Nak
C. Authenticate-Reject
D. Authenticate-Reply
Answer: B
As shown in the figure, both ports GE0/0/1 and GE0/0/2 are configured with different Hybrid configurations.
The correct statement is (). (many selected)
154 of 213
Huawei - H12-211
A. The administrative department and the finance department cannot exchange visits because the VLANs
belonging to the two departments are different.
B. The data frame sent by the administrative department carries the tag in the switch as VLAN20.
C. The data frame sent by the finance department carries the tag in the switch as VLAN20.
D. The switch here can be a Layer 2 switch or a Layer 3 switch because communication does not need to
go through a Layer 3 gateway.
E. If both ports GE0/0/1 and GE0/0/2 of the switch are modified to be trunk ports, the two departments can
communicate normally.
Answer: C D
155 of 213
Huawei - H12-211
Administrators can't manage the AR2200 through Telent. When troubleshooting, find other administrators
have no problems, then which of the following options are possible?
A. The admin user account has been disabled B. The privilege level of the admin user account has been
modified to 0.
Answer: A C
A serial interface of a Huawei router currently using HDLC needs to assign PPP as the encapsulation protocol.
Which of the following commands is required to be configured at the serial interface view?
A. link-protocol ppp
B. encapsulation ppp
C. enable ppp
D. address ppp
Answer: A
<Huawei>system-view
[Huawei]user-interface console 0
[huawei-ui-console0]history-command max-size 20
156 of 213
Huawei - H12-211
D. After the above configuration is completed, the history command cache can save 20 bytes of commands.
Answer: A
The Age time of the RIP route that is viewed by the command on the router is ().
Answer: B
PPP is more secure than HDLC because PPP supports authentication protocols such as ( ). (Choose two)
A. PAP
B. MD5
C. CHAP
D. SSH
Answer: A C
In the PPPoE discovery stage, the PPPoE server assigns a session-id to the PPPoE client in which packet?
A. PADI
B. PADO
C. PADR
D.
157 of 213
Huawei - H12-211
D. PADS
Answer: D
The Ethernet electrical interface can work in 3 duplex modes, and the Ethernet optical interface can only work
in () mode.
A. Full duplex
B. Half duplex
C. Auto-negotiation
D. Simplex
Answer: B C D
According to the command shown above, the correct one in the following description is (). (multiple choice)
[Huawei-GigabitEthernet0/0/1]port link-type access
Answer: A D
Referring to the output result as shown in the figure, it can be judged that the routing table of the router is
composed of a direct route and a static route, and the direct route is
158 of 213
Huawei - H12-211
A. Correct
B. Error
Answer: A
An existing switch is directly connected to the designated port of the peer device through a port, but the port
does not forward any packets but can be connected.
Receive a BPDU to listen for network changes, then the role of the port should be ().
A. Root port
B.
159 of 213
Huawei - H12-211
B. Designated port
C. Alternate port
D. Disable port
Answer: C
160 of 213
Huawei - H12-211
Which of the following is not included in the VRP system login method?
A. Telnet
B. SSH
C. Web
D. Netstream
Answer: D
The subnet mask of a network segment 150.25.0.0 is 255.255.224.0, then () is the valid host address in the
network segment. (multiple choice)
A. 150.25.0.0
B. 150.25.1.255
C. 150.25.2.24
D. 150.15.3.30
Answer: B C
The function of InARP is the opposite of that of ARP. The main purpose is to reversely resolve the known
target MAC address to the protocol address of the peer device on the Ethernet.
A. Yes
B. Wrong
Answer: B
161 of 213
Huawei - H12-211
Which of the following storage media are commonly used by Huawei routers? (multiple choice)
A. SDRAM
B. NVRAM
C. Flash
D. Hard Disk
E. SD Card
Answer: A B C E
When the routers are running in the same OSPF area, the description of their LSDB and routing table is correct
().
(multiple choice)
Answer: A C
A. Yes
B. Wrong
Answer: A
As shown in the figure, if Host A and Host B want to implement inter-VLAN communication through one-arm
162 of 213
Huawei - H12-211
Set?
Answer: B
163 of 213
Huawei - H12-211
Refer to the configuration results of the following output, the correct one in the RIP description is ().
A. Automatic summary is on
Answer: C
164 of 213
Huawei - H12-211
Which command can be used to display the mapping between network address and DLCI on the router?
A. display fr interface
B. display fr
C. display map-info
D. display fr brief
Answer: C
After a fault occurs in the network, the administrator finds out that the configuration of a router has been
modified. What measures should the administrator take to avoid?
A. The administrator should configure all account login devices except the administrator to have a privilege
level of 0.
B. The administrator should configure AAA to authenticate and authorize users who log in to the device.
C. The administrator should configure the ACL to control only the administrator to log in to the device.
D. The administrator should enable port-security on the management port of the route
Answer: A B C
The VRP operating system commands are divided into four levels: access level, monitoring level,
configuration level, and management level. Can run various business configuration commands but not
A. Access level
B. Monitoring level
C. Configuration level
D. Management level
165 of 213
Huawei - H12-211
Answer: C
When two OSPF routers form a TWO WAY-neighbor relationship, the LSDB has completed synchronization,
but the SPF algorithm has not been run.
A. Yes
B. Wrong
Answer: B
The following description of the specified port for the spanning tree is correct.
B. The designated port can forward configuration BPDUs to its connected network segment.
C. The port on the root switch must not be the designated port.
D. Specify the port to forward configuration BPDUs from this switch to the root switch.
Answer: B
As shown in the figure, the G0/0/0 and G0/0/1 interfaces of the RTA are connected to two different network
segments respectively, and the RTA acts as a gateway for the two networks. Host A
Before sending data to host C, it will send an ARP Request to get the MAC address of ().
166 of 213
Huawei - H12-211
A. Host C
D. SWA
Answer: B
The administrator configures OSPF on a router. However, if the loopback interface is not configured on the
router, the description of the router ID is correct.
().
A. The minimum IP address of the physical interface of the router will become the router ID.
B. The maximum IP address of the physical interface of the router will become the router ID.
C. The IP address of the router management interface will become the router ID.
Answer: B
167 of 213
Huawei - H12-211
You cannot create VLAN 4095 when creating a VLAN rule on a Huawei switch. You cannot delete VLAN 1.
A. Correct
B. Error
Answer: A
A. Yes
B. Wrong
Answer: B
A. Yes
B. Wrong
Answer: B
If two IPsec VPN peers want to use both AH and ESP to ensure secure communication, how many do the two
peers need to build?
SA (Security Alliance)?
A. 1
B. 2
C. 3
D.
168 of 213
Huawei - H12-211
D. 4
Answer: D
A frame relay PVC is configured on the router and found to be invalid. What is the possible cause? (multiple
choice)
Answer: B C D
As shown in the broadcast network, OSPF runs on four routers and is in the same area and on the same
network segment. OSPF
A DR and multiple BDRs will be automatically elected to achieve better backup results.
A. Yes
169 of 213
Huawei - H12-211
B. Wrong
Answer: B
After the administrator successfully logs in to the router through Telnet and finds that the IP address of the
interface of the router cannot be configured, the possible causes are (). A. The Telnet terminal software used
by the administrator prohibits the corresponding operation.
The administrator wants to completely delete the old device configuration file config.zip, then the following
command is correct ().
A. delete/force config.zip
B. delete/unreserved config.zip
C. reset config.zip
D. clear config.zip
Answer: B
A. Discovering neighbors
Answer: A B C
170 of 213
Huawei - H12-211
Answer: D
When configuring the router through the Console, the correct setting for the terminal emulator is ().
A. 48006ps, 8-bit data bits, 1-bit stop bit, odd parity and no flow control
B. 96006ps, 8-bit data bit, 1 stop bit, no parity and no flow control
C. 96006ps, 8-bit data bits, 1-bit stop bit, even parity and hardware flow control
D. 192006ps, 8-bit data bit, 1 stop bit, no parity and no flow control
Answer: B
On a frame relay network, a static MAP has been configured on an interface. If you continue to configure the
fr inarp command, the interface will send an Inverse.
The ARP request packet is sent to the peer and the static MAP record is overwritten.
A. Correct
B. Error
Answer: B
If the network address of a network is 192.168.1.0, then its broadcast address must be 192.168.1.255.
A. Correct
171 of 213
Huawei - H12-211
B. Error
Answer: B
What types of networks are supported by the OSPF protocol? (multiple choice)
A. Point-to-Point
B. Broadcast
C. Non-Broadcast Multi-Access
D. Point-to-Multipoint
Answer: A B C D
When two switches use link aggregation technology for interconnection, which of the following conditions do
each member port need to meet? (multiple choice)
A. The number of physical ports connected to the two ends is the same.
B. The physical ports connected to the two ends have the same rate.
C. The physical port duplex mode connected to the two ends is the same.
D. The physical numbers of the physical interfaces connected to the two ends are the same.
E. The optical modules used by the physical ports connected to the two ends are of the same type.
Answer: A B C
As shown in the figure, RTA sends a PADI message to server A as a PPPOE client, and server A replies to a
PADO message. PADO message is One () frame.
172 of 213
Huawei - H12-211
A. Unicast
B. Multicast
C. Broadcast
D. Anycast
Answer: A
As shown in the figure, if the switch runs STP with default parameters, which of the following ports will be
elected as the designated port?
Answer: A
173 of 213
Huawei - H12-211
.ip route-static 10.0.12.0 255.255.255.0 192.168.11 The correct description for this command is ().
D. If the router learns the route of the same network as this route through other protocols, the router will
prefer this route.
Answer: B
A. The next hop in the routing table is redundant. If there is an outgoing interface, the packet can be
forwarded.
Answer: B D
From the perspective of project cutover, there is no need to back up or adjust the configuration file when
upgrading the VRP system, because the lost files can be retrieved in the recycle bin.
A. Yes
B. Wrong
Answer: B
As shown in the figure, the address is configured on the Serial 1/0/1 interface of the RTA using the command
"ip address unnumbered interface loopback 0".
174 of 213
Huawei - H12-211
Answer: B D
When an image file is transmitted over the network using the application software, the TCP/IP encapsulation
process is: data data segment data
A. Correct
B. Error
Answer: A
On the VRP platform, if you want the ping program to use the specified IP address as the source address of the
echo request message, which of the following can be used?
One parameter?
A. -a
B. -s
C. -d
D. -n
Answer: A
175 of 213
Huawei - H12-211
A. SNMPv1
B. SNMPv2
C. SNMPv2c
D. SNMPv3
Answer: A C D
In standard STP mode, which of the following non-root switches forwards the TC set BPDU generated by the
root switch?
A. Root port
B. Backup port
C. Designated port
D. Provisioning port
Answer: C
Refer to the following topology and router configuration. The NAT configuration does not specify a NAT
global address pool, so address translation cannot be performed correctly.
176 of 213
Huawei - H12-211
A. Yes
B. Wrong
Answer: B
The broadcast address is a special address in the network address where the host bits are all set to 1. It can also
be used as a host address.
A. Correct
B. Error
Answer: B
Port aggregation is the aggregation of multiple ports to form an aggregation group to implement load
balancing among member ports. Port aggregation is in
() implemented on.
A.
177 of 213
Huawei - H12-211
A. Physical layer
C. Network layer
D. Transport layer
Answer: B
When an IPsec tunnel is established between two routers, which of the following parameters does not need to
be consistent between IPsec peers?
C. Proposal name
D. Authentication algorithm
Answer: C
Regarding the role of ARP protocol and packet encapsulation, the description is correct ()
B. The MAC address of the destination and the address of the UUID can be obtained through the ARP
protocol.
Answer: D
UDP is connectionless and must use () to provide the reliability of the transmission.
A. Internet Protocol
B.
178 of 213
Huawei - H12-211
Answer: B
Referring to the configuration of the one-arm route in the following figure, it can be judged that even if the
ARP proxy is not enabled on the sub-interface of R1, between the administrative department and the finance
department Can also visit each other.
A. Yes
B. Wrong
179 of 213
Huawei - H12-211
Answer: B
A. 2031:0:720C:0:0:9E0:839A:130B
B. 2031:0:720C:0:0:9E:839A:130B
C. 2031::720C::9E:839A:130B
D. 2031:0:720C::9E0:839A:130B
Answer: A D
The Layer 2 switch belongs to the data link layer device and can identify the MAC address information in the
data frame, forward the data according to the MAC address, and
Some MAC addresses and corresponding port information are recorded in their own internal MAC address
table.
A. Yes
B. Wrong
Answer: A
As shown in the figure, the RTA sends a PADI message to the server A as a PPPOE client. Which of the
following transmission methods will the PADI message use?
180 of 213
Huawei - H12-211
A. Unicast
B. Multicast
C. Broadcast
D. Anycast
Answer: C
C. When an IPv6 message has multiple extension headers, the extension header must appear in an orderly
manner
D. When an IPv6 message has multiple extension headers, the extension header can appear randomly.
Answer: B C
What are the advanced ACLs on Huawei devices that can be used to filter? (multiple choice)
Answer: A C D
217.#
Interface GigabitEthernet0/0/1
181 of 213
Huawei - H12-211
According to the command output shown above, the correct one in the following description is () (multiple
choice)
C. If you want to change the GigabitEthernet0/0/1 port to an Access port, you must first use the command
“undo port trunk allow pass vlan
D. If you want to change the GigabitEthernet0/0/1 port to an Access port, you must first use the command
“undo port trunk allow pass vlan
Answer: B D
With reference to the following topology and configuration, two routers are connected through a serial cable.
If no Layer 2 protocol is specified, PPP is used by default.
Protocol interconnection
182 of 213
Huawei - H12-211
A. Yes
B. Wrong
Answer: A
If the administrator finds that the file cannot be transferred to the Huawei AR2200 through TFTP, what is the
possible cause? ()
Answer: C
When the router's configuration file is saved, which storage medium is generally stored on it?
183 of 213
Huawei - H12-211
A. SDRAM
B. NVRAM
C. Flash
D. Boot ROM
Answer: C
The following description about the ICMP redirect function is correct (). (multiple choice) A. After the router
receives the data packet from an interface and sends the data packet from the interface again, the router will
send ICMP.
B. After the router receives the data packet from an interface, it finds that the IP address of the interface and
the destination IP address of the data packet are on the same network segment.
The router will send an ICMP redirect message to the source device.
C. After the router receives the data packet from an interface and sends the data packet from the interface, the
source device will send an ICMP weight.
D. After the router receives the data packet from an interface, it finds the source IP address of the data packet
and the next hop when the router continues to forward the data packet.
If the IP address belongs to the same network segment, the router will send an ICMP redirect message to the
source device.
A, D
As shown in the figure, the H frame contains an IP packet sent from Host A to Host B, and the destination
MAC address of the H frame is ().
184 of 213
Huawei - H12-211
Answer: D
A. Correct
B. Error
Answer: B
When saving the router's configuration file, which storage medium is usually stored on it?
A. SDRAM
B. NVRAM
C.
185 of 213
Huawei - H12-211
C. Flash
D. Boot ROM
Answer: B
While improving network reliability, STP can also solve loop problems in switched networks.
A. Correct
B. Error
Answer: A
The biggest advantage of NAPT is its flexibility, that is, it can be used as a source address translation, as well
as a destination address translation, and can also be used as a protocol port.
Conversion.
A. Yes
B. Wrong
Answer: B
Answer: A D
186 of 213
Huawei - H12-211
For the description of the PPP link establishment process, the following statement is wrong () (multiple
choice)
A. The Dead phase is also called the physical layer unavailability phase. When both ends of the
communication side detect physical line activation, they will migrate from the Dead phase.
B. During the Establish phase, the PPP link negotiates LCP parameters. Negotiation content includes
maximum receiving unit MRU, authentication method, magic
Word options
C. During the Network phase, the PPP link performs NCP negotiation. Select and configure a network
layer protocol through NCP negotiation, and conduct network
D. After the NCP negotiation is successful, the PPP link will remain in communication and enter the
Terminate phase.
Answer: D E
As shown in the figure, RIP runs between R1 and R2, and R1 cannot learn the route of 2.2.2.2/32 or 2.0.0.0/8.
187 of 213
Huawei - H12-211
A. Correct
B. Error
Answer: A
A Windows host is started for the first time. If the IP address cannot be obtained from the DHCP server, then
the host may use the following one.
IP address?
A. 0.0.0.0
B. 127.0.0.1
C. 169.254.2.33
D. 255.255.255.255
Answer: C
188 of 213
Huawei - H12-211
As shown in the figure, there is a web server in the private network that needs to provide more HTTP services
to the public network users, so the network administrator needs to be at the gateway.
Configure NAT on the router RTA to meet the requirements. The correct configuration to meet the
requirements in the following configurations is ().
A. [RTA-Serial1/0/1] nat server protocol tcp global 202.10.10.1 www inside 192.168.1.1 8080
B. [RTA-Serial1/0/1] nat server protocol tcp global 192.168.1.1 www inside 202.10.10.1 8080
C. [RTA-Gigabitethernet0/0/1] nat server protocol tcp global 202.10.10.1 www inside 192.168.1.1 8080
D. [RTA-Gigabitethernet0/0/1]] nat server protocol tcp global 192.168.1.1 www inside 202.10.10.1 8080
Answer: A
An AR2200 router learned the route entries to the same network and the routes learned through OSPF through
OSPF and RIPv2.
The overhead value is 4882, and the number of hops learned by RIPv2 is 4, and there will be () in the router's
routing table.
A. RIPv2 routing
C. OSPF routing
Answer: C
Which of the following commands can be used to check whether OSPF has correctly established neighbor
189 of 213
Huawei - H12-211
relationships?
Answer: C
A DHCP OFFER packet can carry a DNS address, but can only carry one DNS address.
A. Correct
B. Error
Answer: B
Which of the following commands can be used to check the session status of a PPPoE client?
B. display current-configuartion
Answer: D
The administrator performs the above configuration on the Router. After the completion, a switch is connected
to the G1/0/0 interface of the router.
190 of 213
Huawei - H12-211
[Router-ip-pool-pool 1]quit
[Router-ip-pool-pool 2]quit
D. The obtained IP address may belong to the 10.10.10.0/24 network, or it may belong to the 10.20.20.0/24
network.
Answer: A
The Layer 2 Ethernet switch generates a MAC address table option based on the () packet received by the port.
C. Source IP address
D. Destination IP address
Answer: A
As shown in the figure, all four switches run STP, and various parameters use default values. Sending a block
on a port of the root switch and failing to pass the
191 of 213
Huawei - H12-211
When a port sends a configuration BPDU, how long does the blocked port in the network enter the forwarding
state?
A. About 30 seconds
B. About 50 seconds
C. About 15 seconds
D. About 3 seconds
Answer: B
Network administrators typically use link aggregation technology in their corporate networks. Which of the
following descriptions are the advantages of link aggregation? (multiple choice)
B. Increase bandwidth
C. Improve reliability
D. Improve security
192 of 213
Huawei - H12-211
Answer: A B C
The port cost calculated by STP has a certain relationship with the port bandwidth. That is, the larger the
bandwidth, the more overhead ().
A. small
B. Big
C. Consistent
D. Not necessarily
Answer: A
Answer: A
A. Host
B. Network
C. Multicast
D. Broadcasting
Answer: D
193 of 213
Huawei - H12-211
Which of the following forms of DUID can be configured when DHCPv6 is configured in the VRP system?
(multiple choice)
A. DUID-LL
B. DUID-LLT
C. DUID-EN
D. DUID-LLC
Answer: A B
The above information is the port status information displayed on a switch running STP. Based on this
information. The following description is wrong ().
Answer: C
194 of 213
Huawei - H12-211
NAT can be implemented in a variety of ways, suitable for different scenarios. For example, dynamic NAT
can translate the server address inside the private network into a public IP address.
A. Yes
B. Wrong
Answer: B
This is the three packets that the administrator has captured on the network. The following statement is
incorrect ().
B. The IP address of the Telnet server is 10.0.12.1, and the IP address of the Telnet client is 10.0.12.2.
D. The Telnet client uses the 50190 port to establish a connection with the server.
Answer: B
<Huawei>system - view
B.
195 of 213
Huawei - H12-211
B. Modify the user view command to a permission level of 3, and save the configuration.
D. Modify the permission level of the save command in the user view to 3
Answer: D
If you use a 10 Gigabit optical module to interconnect two Huawei S5700 switches, the working mode of the
interconnect port defaults to full duplex.
A. Correct
B. Error
Answer: A
The administrator found that the above message popped up on the device. The correct statement about this
information is ().
B. If you do not need to enable automatic configuration, the administrator needs to select N
C. When the device is first started, the auto configuration function is enabled.
D. When the device is first started, the auto configuration function is disabled.
Answer: C
As shown in the figure, the packet is encapsulated in IPsec VPN. Which type of packet is encapsulated in
IPsec VPN?
196 of 213
Huawei - H12-211
A. General mode
B. Transmission mode
C. Tunnel mode
Answer: C
As shown in the Display information, when the switch needs to forward a frame with a destination MAC
address of 5489-98ec-f011. The following description is correct
().
A. The switch needs to send a request to discover the device with the MAC address 5489-98ec-f011.
B. The switch will send the target unreachable message to the source device.
C. The switch will flood the frame on all ports except the one that received the frame.
D. The switch did not find a matching entry in the MAC address table, so the frame will be discarded.
Answer: C
197 of 213
Huawei - H12-211
What is the role of the command "interface vlan vlan-id" on the VRP platform?
A. Create a VLAN
D. No such order
Answer: B
In OSPF, which routers does a DR other router exchange link state information with? (multiple choice)
A. DR
B. BDR
C. DR other
Answer: A B
A. Yes
B. Wrong
Answer: B
The backup port in RSTP can replace the failed root port.
B. Error
198 of 213
Huawei - H12-211
The topology and configuration are as shown in the figure. Then, an Eth Trunk logical link can be established
between the two switches. And LSW2 is active end.
A. Correct
B. Error
Answer: B
Network administrators use ping to check network connectivity. Which of the following protocols might be
used in the process?
(multiple choice)
A. ICMP
B. TCP
C. ARP
D. UDP
199 of 213
Huawei - H12-211
Answer: A C
The administrator plans to implement a route backup by configuring a static floating route. The correct
implementation method is ().
A. The administrator needs to configure different protocol priority values for the primary static route and
the alternate static route.
C. The administrator needs to configure different TAGs for the primary static route and the standby static
route.
D. The administrator needs to configure different metrics for the primary static route and the alternate static
route.
Answer: A
D. The switch with the lowest switch priority value in the switched network becomes a non-root switch.
Answer: A B D
As shown in the figure, RTA is a DTE device connected to a frame relay switch. If RTA uses dynamic
mapping to establish a PVC connection, which of the following
200 of 213
Huawei - H12-211
B. [RTA-Serial1/0/1]link-protocol fr
D. [RTA-Serial1/0/1]fr inarp
Answer: C D
The STP root switch is elected based on the comparison of switch priorities. In RSTP, the switch priority and
MAC address are compared. site.
A. Correct
B. Error
Answer: B
On the command line interface of the Huawei AR router, the save command saves the current system time.
A. Correct
B. Error
Answer: B
201 of 213
Huawei - H12-211
When configuring AAA authentication on Huawei AR G3 series routers, how many domains can be
configured?
A. 30
B. 31
C. 32
D. 33
Answer: A
The administrator wants to upgrade the configuration file for the AR2200 via a USB cable, and the following
description is correct (). (multiple choice)
A. Connect the mini USB cable of the PC and AR2200 with a mini USB cable.
B. Connect the USB interface of the PC and AR2200 with a mini USB cable.
C. The AR2200 does not support the use of USB to update configuration files.
D. After connecting the cable, the administrator needs to install the driver for the mini USB.
Answer: A D
There are 50 private IP addresses in a company network. The administrator uses NAT technology to access the
public network, and the company has only one public network address.
A. Static conversion
B. Dynamic conversion
C. easy-ip
D. NAPT
Answer: C
202 of 213
Huawei - H12-211
After deploying a DHCP server on the network, the administrator finds that some hosts have obtained the
address specified by the DHCP server.
B. Some hosts cannot communicate properly with the DHCP server. These host client systems
automatically generate addresses in the range of 169.254.0.0.
C. Some hosts cannot communicate properly with the DHCP server. These host client systems
automatically generate addresses in the range of 127.254.0.0.
D. The address pool of the DHCP server has been completely allocated.
Answer: A B D
The following figure shows the routing table of a router. When the router receives a packet with the
destination IP address of 9.1.1.1, the router forwards the packet according to the route of 9.1.0.0/16 because
the route matches the destination address 9.1. The number of bits in .1.1 is more.
A. Correct
B. Error
203 of 213
Huawei - H12-211
Answer: A
<Huawei>system view
B. Modify the permission level of the save command in the user view to 3
C. Modify the user view command to a permission level of 3, and save the configuration
Answer: B
A. Correct
B. Error
Answer: B
The role of the VLSM is to divide the corresponding number of bits from the host bit portion as a network bit
based on the classful IP address. But on the router
A. Correct
B. Error
Answer: A
204 of 213
Huawei - H12-211
Which of the following functions does the Ctrl+Z key combination have in the VRP system? (multiple choice)
Answer: A B C D E
When using Telnet to log in to the router, which authentication methods can I choose? (choose 2 answers)
A. password authentication
D. Not certified
Answer: A B
A port of the switch is configured as a trunk port, and it is now intended to connect a host to the port to access
the network. The following essential operations are
().
Answer: D
205 of 213
Huawei - H12-211
As shown in the figure, the three Layer 2 switches are interconnected with one HUB, and the STP function is
enabled on the switch. For the bridge ID setting of the STP switch, refer to the following.
Figure, others are the default configuration. The following statement is wrong ().
D. Both ports of LSW1 are designated ports and are in the forwarding state.
Answer: D
206 of 213
Huawei - H12-211
On a Huawei device, if AAA authentication is used for authorization, when the remote server does not
respond, authorization can be performed from the network device.
A. Correct
B. Error
Answer: A
Which of the following IPv6 addresses can be manually configured on the router interface? (multiple choice)
A. fe80:13dc::1/64
B. ff00:8a3c::9b/64
C. ::1/128
Answer: A D
On the VRP interface, you cannot use the command delete or unreserved vrpcfg.zip to delete files. You must
empty them in the recycle bin to thoroughly
Delete Files.
A. Correct
B. Error
Answer: B
As shown in the figure, the network administrator needs to configure static NAT on the RTA so that host A in
the private network can communicate with the public network host C.
207 of 213
Huawei - H12-211
Letter, then the following about the configuration of static NAT, the correct is ()
Answer: D
If the broadcast address of a network is 172.16.1.255, then its network address may be ()?
A. 172.16.2.0
B. 172.16.1.253
C. 172.16.1.128
D. 172.168.1.1
Answer: C
208 of 213
Huawei - H12-211
When the data encapsulation mode of IPSec is tunnel mode, the IP address of the intranet host is hidden. The
reason for this is to protect the entire original packet.
Safety
A. Yes
B. Wrong
Answer: A
The Tracert diagnostic tool records the () of each ICMP TTL timeout message, so that the user can be
provided with the message to reach the destination.
IP address.
A. Destination port
B. Source port
C. Destination IP address
D. Source IP address
Answer: D
When the packet security mode of IPSec is tunnel mode, the IP address of the intranet host is hidden. The
reason for this is to protect the entire original data.
Package security
A. Yes
B. Wrong
C. Yes
D. Wrong
Answer: A
209 of 213
Huawei - H12-211
The network management work manages the network device through the SNMP protocol. When the managed
device has an abnormality, the network management workstation will receive it.
SNMP packets?
A. get-response message
B. set-request message
C. trap message
D. get-request message
Answer: C
When configuring an AR2200 router as a PPPoE client, which of the following configurations is not required?
Answer: C
When RIPv1 is enabled on the Huawei router, the interface that is advertised to the RIP receives the RIPv1
broadcast packet, the RIPv2 broadcast packet, and the multicast packet by default.
A. Yes
B. Wrong
Answer: A
The client has an error accessing the FTP server. If there is no problem checking the connectivity between the
210 of 213
Huawei - H12-211
A. 21
B. 80
C. 20
D. 50649
Answer: A C
How do I enter the view of OSPF area 0 in the VRP operating system? (multiple choice)
A. [huawei]ospf area 0
B. [huawei-ospf-1]area 0
C. [huawei-ospf-1]area 0.0.0.0
D. [huawei-ospf-1]area 0 enable
Answer: B C
A router learns routes to the same destination address through RIP, OSPF, and static routes. By default, VRP
will be the most
A. RIP
B. OSPF
D. Static routing
Answer: B
211 of 213
Huawei - H12-211
On Huawei devices, administrators can announce subnets in RIPV2 because RIPV2 supports VLSM.
A. Correct
B. Error
Answer: B
If the Authenticator sends the wrong username and password to the Authenticator during the PPP
authentication process, what type of Authenticator will send
A. Authenticate-Ack
B. Authenticate-Nak
C. Authenticate-Reject
D. Authenticate-Reply
Answer: B
It is known that the routing table of a router has the following two entries. If the router wants to forward
packets with the destination address of 9.1.4.5, the following is said.
A. Select the first item as the best match because the OSPF protocol has a higher priority.
B. Select the second item as the best match because the RIP protocol has a lower value.
C. Select the second item as the best match because the exit is Ethternet0, which is faster than Serial 0.
D. Select the second term as the best match because the route entry is a more accurate match for the
212 of 213
Huawei - H12-211
D.
destination address 9.1.4.5
Answer: D
213 of 213