ESD

System-Level Solu
tions

ESD Protection Guide

www.ti.com/esd 2018
Table of Contents/Introduction
Introduction Table of Contents
System-level protection for electrostatic Overview of System-Level ESD/EMI Protection
discharge (ESD) is crucial in today’s world,
not only in the industrial space but also in the What is ESD Protection? . . . . . . . . . . . . . . . . . . . . . . 3
consumer and automotive space. It only takes Why External ESD . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
one ESD strike to permanently damage a
product, which makes ESD protection a critical ESD-Solutions Quick Reference by Interface . . . 5
component in a system design.
ESD-Solutions by Application
This selection guide will briefly explain how Definitions of ESD Device Specifications . . . . . . . . . 6
ESD devices from Texas Instruments can help
Antenna Circuit Protection . . . . . . . . . . . . . . . . . . . . . 7
avoid catastrophic system failures caused by
ESD strikes. Audio Circuit Protection . . . . . . . . . . . . . . . . . . . . . . . 8
Ethernet Circuit Protection.... . . . . . . . . . . . . . . . . . . 9
Electromagnetic interference (EMI) is another
challenge often faced in system design. EMI HDMI Circuit Protection . . . . . . . . . . . . . . . . . . . . . . 10
is a radio-frequency (RF) (800 MHz to 2 GHz) Pushbutton and Keypad Circuit Protection . . . . . . 11
disturbance where electromagnetic conduction SD and SIM Cards Circuit Protection . . . . . . . . . . . 12
from an external source affects an electrical
USB 2.0 Circuit Protection . . . . . . . . . . . . . . . . . . . . 13
circuit. EMI can be avoided by using EMI filters
that eliminate RF noise and maintain USB 3.1 Gen 1 Circuit Protection . . . . . . . . . . . . . . 14
signal integrity. USB 3.1 Gen 2 Circuit Protection . . . . . . . . . . . . . . 15
To learn more about ESD protection and TI’s USB Type-C Circuit Protection . . . . . . . . . . . . . . . . 16
ESD devices, visit: 4-20-mA Loop Circuit Protection . . . . . . . . . . . . . . 17

www.ti.com/esd TI Worldwide Technical Support . . . . . . . . . . . . . 18

2 System Level ESD Protection Guide Texas Instruments 2018

Overview of System-Level ESD Protection
➔ What is ESD Protection?
Electrostatic discharge (ESD) is the If ESD protection is not present In the event of an ESD strike, the
sudden release of electricity from in a system, the high voltage of ESD diode would breakdown and
one charged object to another an ESD strike via an interface create a low impedance path that
when the two objects come into connection would cause a large limits the peak voltage and current
contact. While we’ve all expe- current spike to flow directly into by diverting the current flow to
rienced ESD when we’ve been the IC, causing damage. ground, thereby protecting the IC.
shocked by a metal doorknob or
car door, most ESD strikes are To protect sensitive circuitry from The plots below compares the
quite harmless to humans. Howev- electrical overstress failures, ESD peak voltage of a typical ESD
er, for sensitive integrated circuits protection diodes are connected strike without protection (black) to
(ICs), the high peak voltage and to each signal line between the the same ESD strike on a signal
current of these ESD strikes can interface connector and the IC. line with ESD diode
cause catastrophic failures. protection (red).

Interface Interface
Connector Connector
IC Protected IC

ESD Diode

ESD strike without protection. ESD strike with protection.

Voltage waveforms with and without ESD protection.

3 System Level ESD Protection Guide Texas Instruments 2018

Overview of System-Level ESD Protection
➔ Why External ESD?
Semiconductor devices based off The silicon area required to Stand-alone ESD devices from
of advanced processes only offer implement system-level ESD Texas Instruments (TI) provide
device-level ESD specifications protection is much larger than space-saving and cost-effective
like the charge device model what is required for device-level solutions to protect system ICs
(CDM) and the human body model HBM and CDM. This difference in from external ESD strikes while
(HBM) shown below. Device- silicon area translates to additional maintaining signal integrity.
level ESD specifications are not cost. As technology gets smaller, it
sufficient to protect devices in becomes increasingly difficult and ESD protection is often considered
a system. more costly to integrate sufficient at the last phase of system design.
system-level protection with Designers need flexibility to select
The energy associated with a microcontroller or core chipsets. an ESD device that does not
system-level ESD strike is much compromise the PCB layout or
higher than a device-level ESD System-level ESD protection consume additional board space.
strike. This means a more robust can be added with discrete TI’s ESD solutions with flow-
design is required to protect components. However, in many through packaging allow designers
against this excess energy. applications, discrete solutions to add ESD components in the
consume board space, complicate final stages of a design without
layout, and compromise signal any change in the board layout.
integrity at high data rates.

48 A Legend
Charge Device Model (CDM)
Human Body Model (HBM)
System Level IEC
ESD Models for CDM,
24 A
Standard Model HBM and IEC.

50 ns 100 ns

Left: Silicon die areas for system-

level ESD (8-kV IEC).
Pad

Pad
Right: Silicon die areas for device-
level ESD (2-kV HBM).

4 System Level ESD Protection Guide Texas Instruments 2018

ESD-Solutions Quick Reference by Interface

USB 3.1 Gen 2 (10 Gbps)

➔

LVDS (up to 1.5 Gbps)

1394 (up to 1.6 Gbps)

RS-485/432/422/232
Keypad/Push Button
PCIe Gen 3 (8 Gbps)
LCD Display (17 pF)

LED (up to 24 pF)

4–20-mA Loop

SATA (6 Gbps)
MHL (3 Gbps)
HDMI 1.4/1.3

SD/SIM Card

VGA (2.5 pF)

Display Port

USB Type-C

SIM Card
Ethernet
Antenna

USB 2.0

USB 3.0
(15pF)
Audio

HART
GPIO
Channel Device

I2C
ESD401 R R R

TPD1E01B04 R ★ ★ R R R R

TPD1E04U04 R R R R R R ★ R

TPD1E05U06 R R ★ R R ★ ★ R

TPD1E0B04 ★ R R R
1
TPD1E10B06 ★ ★
TPD1E10B09 ★
TPD1E1B04 R R R R

TPD1E6B06 R R R R

TVS3300 ★ ★
ESD122 R R R R R R R ★ ★
TPD2E001 R

TPD2E007 R R R R R
2
TPD2E009 R R R

TPD2E1B06 R R R

TPD2E2U06 ★ ★ ★ ★
TPD4E001 R R R

TPD4E02B04 R ★ ★ R R

TPD4E05U06 R R R R R R ★ ★ R R

TPD4E101 ★ ★
4
TPD4E1U06 ★ R

TPD4E6B06 R R R

TPD4F202 R

TPD4S009 R R

TPD6E05U06 R R ★
6 TPD6F003 R R R

TPD6F202 ★ R

TPD8E003 R

8 TPD8F003 R R R

TPD8S009 R

★ Best Solution R Recommended Solution

5 System Level ESD Protection Guide Texas Instruments 2018

ESD Solutions by Application
➔ Definitions of ESD Device Specifications
The following sections show ESD protection solutions for popular interface applications and includes
selection tables with recommended ESD protection. The selection tables highlight some important
specifications and features of the devices. Below are descriptions of the parameters used in the
selection tables.

1 Working Voltage (VRWM) 4 Channels

The working voltage is the recommended operating ESD devices can come in a variety of channels
voltage of the ESD device. The interface’s signal and configurations. Depending on the interface,
voltage should not exceed the working voltage of the multi-channel devices may offer board-space savings
ESD device in either the negative or positive direction over single-channel devices. In other applications,
to prevent unwanted clamping and leakage. single-channel devices may offer more design
Learn more: www.ti.com/ESD-VRWM flexibility than multi-channel solutions.

2 IEC 61000-4-2 Rating 5 Clamping Voltage at 16-A TLP

A system-level ESD standard that shows the robust- When an ESD strike occurs, the ESD diode will
ness of the ESD device. The IEC 61000-4-2 rating “clamp” the voltage so that the downstream cir-
consists of two measurements. First, the contact rat- cuitry will not be exposed to a voltage greater than
ing shows the maximum voltage a device can with- the clamping voltage. Therefore, clamping voltage
stand when the source of ESD is discharged directly is a measurement of how well the diode can pro-
onto the device. Second, the air-gap rating shows the tect downstream circuitry. The clamping voltage of
maximum voltage a device can withstand when the a device exposed to an 8-kV IEC ESD strike is best
source of ESD is discharged over a gap of air onto approximated with a transmission line pulse (TLP)
the device. The higher the IEC 61000-4-2 rating, the at 16 A.
higher a voltage the ESD device can withstand. Learn more: www.ti.com/ESD-ClampingVoltage
Learn more: www.ti.com/ESD-Rating

3 Capacitance
Since the ESD diodes are connected in parallel to the
signal trace, they add some parasitic capacitance to
the system. The capacitance of the ESD device be-
comes especially important in high-speed interfaces
because capacitance must be minimized to maintain
signal integrity.
Learn more: www.ti.com/ESD-Capacitance

6 System Level ESD Protection Guide Texas Instruments 2018

ESD Solutions by Application
➔ Antenna Circuit Protection

WiFi Power Filtering

Transceiver Amplifier Network

Description: In wireless applications such as GPS, WLAN, Wi-Fi®, etc., the antenna can act as a
low-impedance path for ESD strikes to enter the system and damage downstream circuitry such as the
filtering network, amplifier or transceiver. Signal frequencies in these applications can reach up to 15 GHz
which means that any capacitance on signal paths must be minimized to avoid signal degradation. The
peak-to-peak voltage of these signals do not usually exceed ±1 V so ESD diodes must have a working
voltage to tolerate these voltage swings.

Solution: The ESD solutions in the table below provide IEC 61000-4-2 ESD protection with ultra-low
capacitance to maintain signal integrity. These solutions come in a variety of flow-through footprint options,
including 0201 (0.6 x 0.3 mm), 0402 (1.0 x 0.6 mm) and DFN (2.5 x 1.0 mm). Each device also supports up to
a ±3.6-V working voltage making it a suitable solution for antenna applications.

ESD Solutions for Antenna Applications

IEC 61000-4-2
Working Voltage Capacitance Package Size
Device ESD Rating (kV) Channels Package
(V) (pF) (mm)
(Contact/Air Gap)
TPD1E0B04DPY ±3.6 8/9 0.13 1 1.0 x 0.6 0402

TPD1E0B04DPL ±3.6 8/9 0.13 1 0.6 x 0.3 0201

TPD1E01B04DPY ±3.6 15/17 0.18 1 1.0 x 0.6 0402

TPD1E01B04DPL ±3.6 15/17 0.18 1 0.6 x 0.3 0201

7 System Level ESD Protection Guide Texas Instruments 2018

ESD Solutions by Application
➔ Audio Circuit Protection

Audio Amplifier
Class AB L Audio
L Audio IN (ESD Sensitive) L
GND

R Audio IN
Speaker
Audio Amplifier R Audio
Connector
Class AB
(Source of ESD)
(ESD Sensitive)
R
GND

GND

Description: Audio jacks and connectors can present an entry point for ESD to enter the system. Audio
signals do not typically exceed ±5 V before amplification but can reach higher voltages after the amplifier.
Since the maximum frequency does not exceed 30 kHz, the capacitance of the ESD diode is not a concern.
Because analog audio can have both positive and negative voltage swings, ESD solutions should be
bidirectional to prevent premature breakdown which would interfere with the signal.

Solution: The ESD solutions below offer ESD protection that exceeds the IEC 61000-4-2 level 4 standard.
These solutions are bidirectional while allow for both the positive and negative voltage swings of audio
signals. The solutions below also come in a variety of working voltages to support different
audio-voltage levels.

ESD Solutions for Audio Applications

IEC 61000-4-2
Working Voltage Capacitance Package Size
Device ESD Rating (kV) Channels Package
(V) (pF) (mm)
(Contact/Air Gap)
TPD1E10B09DPY ±9 20/20 10 1 1.0 x 0.6 0402

TPD1E1B04DPY ±3.6 30/30 1 1 1.0 x 0.6 0402

TPD2E1B06DRL ±5.5 10/15 0.85 2 1.6 x 1.2 SOT-6

TPD2E007YFM ±12 8/15 15 2 0.77 x 0.77 DSLGA-4

8 System Level ESD Protection Guide Texas Instruments 2018

ESD Solutions by Application
➔ Ethernet Circuit Protection

TPD4E1U06

Tx+

Tx–
RJ45 Ethernet
Connector Transceiver
Rx+ (PHY)

Rx–

Description: Ethernet applications will require 4 channels of ESD protection for the Tx/Rx signal lines in the
connector. The voltage of these signals can range from 1 V to 2.5 V and the bandwidth options include 10
Mbps, 100 Mbps for Fast Ethernet, and 1 Gbps for Gigabit Ethernet. At these speeds, the capacitance of the
ESD diode should be taken into account.

Solution: Unidirectional ESD protection devices are recommended for Ethernet applications because they
offer superior protection in the negative direction. Capacitance also needs to be taken into account, especially
for Gigabit Ethernet (<4.5 pF is recommended).

ESD Solutions for Ethernet Applications

IEC 61000-4-2
Working Voltage Capacitance Package Size
Device ESD Rating (kV) Channels Package
(V) (pF) (mm)
(Contact/Air Gap)
TPD4E1U06DCK 5.5 12/15 0.8 4 2.0 x 1.25 SC70

TPD4E05U06DQA 5.5 12/15 0.4 4 2.5 x 1.0 USON-10

TPD1E05U06DPY 5.5 12/15 0.5 1 1.0 x 0.6 0402

9 System Level ESD Protection Guide Texas Instruments 2018

ESD Solutions by Application
➔ HDMI Circuit Protection

HDMI Connector TPD4E02B04

TMDS_D2+
TMDS_D2–
TMDS_D1+
TMDS_D1–
TPD4E02B04
TMDS_D0+
TMDS_D0– HDMI
TMDS_CLK+ Controller
TMDS_CLK–
TPD4E05U06
CEC
Utility
DDC_CLK
DDC_DAT

Description: The HDMI connector requires ESD protection for all 12 data lines: eight low-voltage, high-speed
TMDS lines and four 5-V control lines. The speed of the TMDS lines can reach a maximum of 6 Gbps per lane
(18 Gbps for the whole connector) for HDMI 2.0 so minimizing capacitance is crucial.

Solution: For the 8 TMDS lines, two 4-channel ESD devices with ultra-low capacitance are recommended
to minimize board layout and maintain signal integrity. A 5-V tolerant, 4-channel device should be used to
protect the lower-speed control lines. A 5-V tolerant, 6-channel device can be substituted here to protect the
5-V power line as well.

ESD Solutions for HDMI Applications

IEC 61000-4-2
Working Voltage Capacitance Package Size
Device ESD Rating (kV) Channels Package
(V) (pF) (mm)
(Contact/Air Gap)
TPD4E02B04DQA ±3.6 12/15 0.25 4 2.5 x 1.0 USON-10

TPD4E05U06DQA 5.5 12/15 0.4 4 2.5 x 1.0 USON-10

TPD1E04U04DPL 3.6 16/16 0.5 1 0.6 x 0.3 0201

TPD6E05U06RVZ 5.5 12/15 0.47 6 3.5 x 1.35 USON-14

10 System Level ESD Protection Guide Texas Instruments 2018

ESD Solutions by Application
➔ Keypad and Pushbutton Circuit Protection

IO Line 1

1
IO Line 2

2
1 1 ESD Sensitive Device

Push 2 2 GND Line

Buttons

Description: Pushbuttons/keyboards on cell phones, laptops and TVs are high-contact areas that can
present a low-impedance path for ESD to enter the system. These I/O signals are typically low speed and
low voltage (<5 V).

Solution: Since the signal frequency of pushbuttons is low, the capacitance of the ESD device is not very
important. Single-channel and multi-channel solutions with IEC 61000-4-2 ESD protection are
suitable solutions.

ESD Solutions for Keypad and Pushbutton Applications

IEC 61000-4-2
Working Voltage Capacitance Packae Size
Device ESD Rating (kV) Channels Packae
(V) (pF) (mm)
(Contact/Air Gap)
TPD1E10B06DPY ±5.5 30/30 12 1 1.0 x 0.6 0402

TPD1E1B04DPY ±3.6 30/30 1 1 1.0 x 0.6 0402

TPD1E6B06DPL ±5.5 15/15 6 1 0.6 x 0.3 0201

TPD2E007YFM ±12 8/15 15 2 0.77 x 0.77 DSLGA-4

11 System Level ESD Protection Guide Texas Instruments 2018

ESD Solutions by Application
➔ SD- and SIM-Card Circuit Protection

DAT2

DAT3 TPD4E101

CMD IO
SD Card
SD Card

GND
Controller
VDD
TPD1E6B06
CLK

GND

DAT0
TPD1E6B06
TPD1E6B06
DAT1

Description: SD cards have seven pins that require ESD protection: four data pins (DAT0, DAT1, DAT2, DAT3),
a clock pin (CLK), input and output command (CMD IO), and the 2.6- to 3.3-V power pin (VDD). The sequential
write speed of the fastest SD speed class is 90 Mbps (VSC90) so the capacitance on these interface lines do
not need to be minimized. SIM cards have similar specs and do not need capacitance to be minimized.

Solution: The footprint of the ESD solutions must be as small as possible because the board space around
the SD card is very constrained. The TPD4E101DPW is one of the smallest 4-channel ESD devices in the
industry but single-channel devices can also be used to minimize board space.

ESD Solutions for SD- and SIM-Card Applications

IEC 61000-4-2
Working Voltage Capacitance Package Size
Device ESD Rating (kV) Channels Package
(V) (pF) (mm)
(Contact/Air Gap)
TPD4E101DPW ±5.5 15/15 4.8 4 0.8 x 0.8 X2SON-4

TPD1E6B06DPL ±5.5 15/15 6 1 0.6 x 0.3 0201

TPD1E04U04DPL 3.6 16/16 0.5 1 0.6 x 0.3 0201

12 System Level ESD Protection Guide Texas Instruments 2018

ESD Solutions by Application
➔ USB 2.0 Circuit Protection

TPD1E10B06 Battery
Charger
VBUS

ESD122
Connector
USB 2.0

D–

USB
Transceiver
D+

Description: The USB 2.0 connector has four pins: VBUS for power, D+ and D– for differential data signals
and a ground pin. The VBUS pin will carry a 5-V DC power supply so the capacitance on this line will be of little
importance. The D+ and D– data lines will carry a 480-Mbps differential signal.

Solution: The VBUS line will require ESD protection with at least a 5-V working voltage to ensure that
breakdown does not occur in normal operation. The D+ and D– data lines will require low-capacitance ESD
protection that can support a 480-Mbps signal. Single-channel and dual-channel devices are good solutions
to simplify routing.

ESD Solutions for USB 2.0 Applications

IEC 61000-4-2
Working Voltage Capacitance Package Size
Device ESD Rating (kV) Channels Package
(V) (pF) (mm)
(Contact/Air Gap)
TPD1E10B06DPY ±5.5 30/30 12 1 1.0 x 0.6 0402

TPD1E05U06DPY 5.5 12/15 0.5 1 1.0 x 0.6 0402

TPD1E1B04DPY ±3.6 30/30 1 1 1.0 x 0.6 0402

ESD122DMX ±3.6 18/18 0.2 2 1.0 x 0.6 DMX

TPD2E1B06DRL ±5.5 8/15 0.85 2 1.6 x 1.2 SOT-6

13 System Level ESD Protection Guide Texas Instruments 2018

ESD Solutions by Application
➔ USB 3.1 Gen 1 Circuit Protection

TPD1E10B06 Battery
Charger
VBUS

TPD6E05U06
D–
D+
USB 3 Connector

Tx+

USB
Transceiver
Tx–
Rx+
Rx–

Description: USB 3.1 Gen 1 incorporates the Tx/Rx differential lines to handle speeds up to 5 Gbps. For
these speeds, the capacitance of ESD protection must be minimized to maintain signal integrity.

Solution: ESD solutions for USB 3.1 Gen 1 should have a capacitance of 0.5 pF or lower for signal-integrity
purposes and have a working voltage of >3.6 V. A low-capacitance, 6-channel ESD solution for the data lines
(D+/D–, Tx, Rx) combined with a 5-V single-channel ESD device for the VBUS lines would be one solution for
USB 3.1 Gen 1.

ESD Solutions for USB 3.1 Gen 1 Applications

IEC 61000-4-2
Working Voltage Capacitance Package Size
Device ESD Rating (kV) Channels Package
(V) (pF) (mm)
(Contact/Air Gap)
TPD6E05U06RVZ 5.5 12/15 0.47 6 3.5 x 1.35 USON-14

TPD1E10B06DPY ±5.5 30/30 12 1 1.0 x 0.6 0402

TPD4E05U06DQA 5.5 12/15 0.4 4 2.5 x 1.0 USON-10

TPD1E05U06DPY 5.5 12/15 0.5 1 1.0 x 0.6 0402

14 System Level ESD Protection Guide Texas Instruments 2018

ESD Solutions by Application
➔ USB 3.1 Gen 2 Circuit Protection

TPD1E10B06 Battery
Charger
VBUS

ESD122
D–
USB 3 Connector

D+

TPD4E02B04
Tx+

USB
Transceiver
Tx–
Rx+
Rx–

Description: USB 3.1 Gen 1 incorporates the Tx/Rx differential lines to reach speeds up to 10 Gbps. For
these speeds, the capacitance of ESD protection must be minimized to maintain signal integrity.

Solution: ESD solutions for the Tx/Rx lines of USB 3.1 Gen 2 should have a capacitance of 0.3 pF or lower for
signal integrity purposes and have a working voltage of >3.6 V. One solution is a 4-channel ESD device with
ultra-low capacitance for the datalines (Tx, Rx), combined with a 2-channel ESD device with low capacitance
for D+/D– and a single-channel ESD device for the VBUS line.

ESD Solutions for USB 3.1 Gen 2 Applications

IEC 61000-4-2
Working Voltage Capacitance Package Size
Device ESD Rating (kV) Channels Package
(V) (pF) (mm)
(Contact/Air Gap)
TPD4E02B04DQA ±3.6 12/15 0.25 4 2.5 x 1.0 USON-10

ESD122DMX ±3.6 18/18 0.2 2 1.0 x 0.6 DMX

TPD1E10B06DPY ±5.5 30/30 12 1 1.0 x 0.6 0402

15 System Level ESD Protection Guide Texas Instruments 2018

ESD Solutions by Application
➔ USB Type-CTM Circuit Protection

USB Type-C Connector

Rx1 Tx1 SBU2 SBU1 USB 2.0 CC1 CC2 Tx2 Rx2

ESD122 (x2) TPD1E05U06 ESD122 (x2) TPD1E05U06 ESD122 (x2)

USB USB
SuperSpeed SuperSpeed
Switch PD Controller Switch

Description: USB Type-CTM has a 24-pin connector that can support USB 3.1 Gen2, DisplayPort, HDMI, and
a variety of other alternate modes. There are 16 pins that require ESD protection. Since the SuperSpeed USB
lines for USB 3.1 Gen2 (Tx1+, Tx1–, Rx1+, Rx1–, Tx2+, Tx2–, Rx2+ and Rx2–) can reach speeds up to 10
Gbps, capacitance must be minimized. The USB 2.0 lines (D+ top, D+ bottom, D– top and D– bottom) also
require low capacitance. The CC1, CC2 and SBU1, SBU2 Type-C pins can reach up to 5.5 V and while low
capacitance is not required, it is recommended for applications that use alternate modes.

Solution: The USB Type-C connector houses 24 pins in a small form factor so board space becomes very
constrained. For this reason, space-saving 2-channel ESD devices with ultra-low capacitance (ESD122) are
recommended for all high-speed data lines in USB Type-C. Single-channel 5.5-V ESD devices (TPD1E05U06)
are recommended for the SBU and CC lines to simplify routing to the PD or CC controller. However,
4-channels can also be used if preferred.

ESD Solutions for USB Type-C Applications

IEC 61000-4-2
Working Voltage Capacitance Package Size
Device ESD Rating (kV) Channels Package
(V) (pF) (mm)
(Contact/Air Gap)
ESD122DMX ±3.6 18/18 0.2 2 1.0 x 0.6 DMX

TPD1E05U06DPY 5.5 12/15 0.42 1 1.0 x 0.6 0402

TPD1E01B04DPY ±3.6 15/17 0.18 1 1.0 x 0.6 0402

TPD4E02B04DQA ±3.6 12/15 0.25 4 2.5 x 1.0 USON-10

16 System Level ESD Protection Guide Texas Instruments 2018

ESD Solutions by Application
➔ 4-20-mA Protection

Field Transmitter VSource

4–20-mA
Loop Cable
4–20-mA
Sensor Transmitter PLC

4–20-mA
Loop Cable Receiver

Description: The 4–20-mA signal standard is one of the most popular interfaces for sensor-signal
transmission in industrial applications. At a high level, the programmable logic controller (PLC) will supply a
voltage source to power the system. The field transmitters and sensors will use this source to transmit the
data they receive from the external environment in the form of a 4–20-mA current which is measured by the
receiver in the PLC. This 4–20-mA loop has the advantage of transmitting data with little to no signal loss.
However, since the 4–20-mA cables can be very long, there are opportunities for ESD (IEC 61000-4-2) and
surge (IEC 61000-4-5) pulses to couple onto the cable and damage the system.

Solution: Surge diodes that are rated to IEC 61000-4-2 and IEC 61000-4-5 must be placed in front of the
transmitter, source, and receiver to protect them from a surge or ESD strike that can couple onto the long
4–20-mA cable. Since most 4–20-mA voltage sources are 24 V, a diode with a slightly higher working voltage
is a suitable solution. Since PLC I/O modules and field transmitters can get space constrained, the smaller the
protection diodes, the better.

ESD Solutions for 4-20mA Loop Applications

IEC 61000-4-2 IEC 61000-4-5

Working Voltage Package Size
Device ESD Rating (kV) Surge Rating Channels Package
(V) (mm)
(Contact/Air Gap) (A)
TVS3300YZF 33 11/30 35 1 1.1 x 1.1 WCSP-4

TVS3300DRV 33 14/30 35 1 2x2 SON-6

17 System Level ESD Protection Guide Texas Instruments 2018

TI Worldwide Technical Support
TI Support TI Training
Thank you for your business. Find the answer to your support need or get From technology fundamentals to advanced implementation, we offer
in touch with our support center at on-demand and live training to help bring your next-generation designs to
www.ti.com/support life. Get started now at

China: training.ti.com
http://www.ti.com.cn/guidedsupport/cn/docs/supporthome.tsp China:
Japan: http://www.ti.com.cn/general/cn/docs/gencontent.tsp?contentId=71968
http://www.tij.co.jp/guidedsupport/jp/docs/supporthome.tsp Japan:
https://training.ti.com/jp

Technical support forums

Important Notice: The products and services of Texas Instruments
Search through millions of technical questions and answers at TI’s E2E™ Incorporated and its subsidiaries described herein are sold subject to TI’s
standard terms and conditions of sale. Customers are advised to obtain the
Community (engineer-to-engineer) at most current and complete information about TI products and services before
placing orders. TI assumes no liability for applications assistance, customer’s
e2e.ti.com applications or product designs, software performance, or infringement of
patents. The publication of information regarding any other company’s products
China: or services does not constitute TI’s approval, warranty or endorsement thereof.
http://www.deyisupport.com/
Japan:
http://e2e.ti.com/group/jp/
The platform bar and E2E are trademarks of Texas Instruments.
All other trademarks are the property of their respective owners.

© 2018 Texas Instruments Incorporated SSZB130C

 IMPORTANT NOTICE FOR TI DESIGN INFORMATION AND RESOURCES

Texas Instruments Incorporated (‘TI”) technical, application or other design advice, services or information, including, but not limited to,
reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to assist designers who are
developing applications that incorporate TI products; by downloading, accessing or using any particular TI Resource in any way, you
(individually or, if you are acting on behalf of a company, your company) agree to use it solely for this purpose and subject to the terms of
this Notice.
TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI
products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,
enhancements, improvements and other changes to its TI Resources.
You understand and agree that you remain responsible for using your independent analysis, evaluation and judgment in designing your
applications and that you have full and exclusive responsibility to assure the safety of your applications and compliance of your applications
(and of all TI products used in or for your applications) with all applicable regulations, laws and other applicable requirements. You
represent that, with respect to your applications, you have all the necessary expertise to create and implement safeguards that (1)
anticipate dangerous consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that
might cause harm and take appropriate actions. You agree that prior to using or distributing any applications that include TI products, you
will thoroughly test such applications and the functionality of such TI products as used in such applications. TI has not conducted any
testing other than that specifically described in the published documentation for a particular TI Resource.
You are authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that include
the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO
ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY
RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or
endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR
REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING TI RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO
ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL
PROPERTY RIGHTS.
TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY YOU AGAINST ANY CLAIM, INCLUDING BUT NOT
LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF PRODUCTS EVEN IF
DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL, DIRECT, SPECIAL,
COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN CONNECTION WITH OR
ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
You agree to fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of your non-
compliance with the terms and provisions of this Notice.
This Notice applies to TI Resources. Additional terms apply to the use and purchase of certain types of materials, TI products and services.
These include; without limitation, TI’s standard terms for semiconductor products http://www.ti.com/sc/docs/stdterms.htm), evaluation
modules, and samples (http://www.ti.com/sc/docs/sampterms.htm).

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2018, Texas Instruments Incorporated