User’s Guide

600A True RMS AC/DC

Clamp Meter

Model 38389
Safety
International Safety Symbols
This symbol, adjacent to another symbol or terminal,
indicates the user must refer to the manual for further
information.

This symbol, adjacent to a terminal, indicates that, under

normal use, hazardous voltages may be present

Double insulation

SAFETY NOTES
• Do not exceed the maximum allowable input range of any function
• Do not apply voltage to meter when resistance function is selected.
• Set the function switch OFF when the meter is not in use.
• Remove the battery if meter is to be stored for longer than 60 days.
WARNINGS
• Set function switch to the appropriate position before measuring.
• When measuring volts do not switch to current/resistance modes.
• Do not measure current on a circuit whose voltage exceeds 600V.
• When changing ranges using the selector switch always disconnect
the test leads from the circuit under test.
• Do not exceed the maximum rated input limits.
UL
A UL mark does not indicate that this product has been evaluated for
the accuracy of its readings.

2 38389 V2.6 10/03

CAUTIONS
• Improper use of this meter can cause damage, shock, injury or
death. Read and understand this user manual before operating the
meter.
• Always remove the test leads before replacing the battery or fuses.
• Inspect the condition of the test leads and the meter itself for any
damage before operating the meter. Repair or replace any damage
before use.
• Use great care when making measurements if the voltages are
greater than 25VAC rms or 35VDC. These voltages are considered
a shock hazard.
• Remove the battery if the meter is to be stored for long periods.
• Always discharge capacitors and remove power from the device
under test before performing Diode, Resistance or Continuity tests.
• Voltage checks on electrical outlets can be difficult and misleading
because of the uncertainty of connection to the recessed electrical
contacts. Other means should be used to ensure that the terminals
are not "live".
• If the equipment is used in a manner not specified by the
manufacturer, the protection provided by the equipment may be
impaired.

Input Limits
Function Maximum Input
A AC, A DC 600A
V DC, V AC 600V DC/AC
Resistance, Capacitance, Diode Test 250V DC/AC
Temperature 60V DC, 24V AC

3 38389 V2.6 10/03

Meter Description

1. Current clamp
2. Data Hold button 1
3. Peak Hold button
4. Mode select button
2
5. ZERO button
3 8
6. LCD display
4 9
7. COM input jack 5
8. Clamp trigger
6
9. Rotary Function switch
10. V/Ω/CAP/TEMP jack 7 10

1. AC (alternating current) and DC (direct currrent)

2. Minus sign
3. 4000 count (0 to 3999) measurement reading
4. AutoRange mode
4 5 6 7 8 9
5. Peak Hold mode
10
6. Diode test mode
1
7. Audible Continuity
2 11
8. Data Hold mode
9. ZERO (Relative) mode
3
10. Low Battery icon
11. Units of measure list

4 38389 V2.6 10/03

Specifications
Function Range & Resolution Accuracy (% of reading)
DC Current 400.0 ADC 0 to 70A: ± (2.5% + 0.6A)
70 to 300A: ± (3.0% + 0.3A)
300 to 400A ± (3.5% + 0.3A)
600 ADC 0 to 150A: ± (2.5% + 4A)
151 to 350A: ± (3.0% + 4A)
351 to 600A: ± (4.0% + 6A)
AC Current 400.0 AAC 0 to 70A: ± (3.0% + 0.6A)
70 to 300A: ± (3.5% + 0.3A)
300 to 400A ± (3.5% + 0.6A)
600 AAC 0 to 150A: ± (3.0% + 4A)
151 to 350A: ± (3.5% + 5A)
351 to 600A: ± (4.0% + 8A)
DC Voltage 400.0 mVDC ± (0.5% + 5 digits)
4.000 VDC
40.00 VDC ± (1.2% + 3 digits)
400.0 VDC
600 VDC ± (1.5% + 3 digits)
AC Voltage 4.000 VAC ± (1.0% + 5 digits)
40.00 VAC
± (1.5% + 3 digits)
400.0 VAC
600 VAC ± (2.0% + 4 digits)
Resistance 400.0 Ω ± (1.0% + 4 digits)
4.000KΩ
40.00KΩ ± (1.5% + 2 digits)
400.0KΩ
4.000MΩ ± (2.0% + 3 digits)
40.00MΩ ± (3.0% + 5 digits)
o
Temperature -4 to 1400 F ± (3.0% + 5 oF)
o
-20 to 760 C ± (3.0% + 3 oC)

5 38389 V2.6 10/03

Function Range & Resolution Accuracy (% of reading)
Capacitance 40.00 nF ± (5.0% + 7 digits)
400.0 nF
4.000 uF ± (3.5% + 5 digits)
40.00 uF
100.0 uF ± (5.0% + 5 digits)
Clamp size Opening 1.3" (33mm) approx.
Diode Test Test current of 0.3mA typical;
Open circuit voltage 1.5V DC typical.
Continuity Check Threshold <50Ω; Test current < 1mA
Low Battery Indication “BAT” is displayed
Overrange Indication “1 “ is displayed
Measurements Rate 2 per second, nominal
Temperature sensor Type K thermocouple
Input Impedance 7.8MΩ (VDC and VAC)
Display 3-3/4 digits (4000 counts) LCD
AC bandwidth 50/60Hz (AAC and VAC)
AC response True rms (AAC and VAC)
o o
Operating Temperature 14 to 122 F (-10 to 50 C)
o o
Storage Temperature -14 to 140 F (-30 to 60 C)
o o o o
Relative Humidity 90%(0 C to 30 C); 75%(30 C to 40 C);
o o
45%(40 C to 50 C)
Altitude Operating: 3000m; Storage 10,000m
Over voltage Category II 600V
Battery 9V Battery
Auto OFF After 15 minutes of inactivity
Dimensions/Weight 8x3.2x1.7" (204x80x43mm)/0.62 lbs. (281g)
Safety For indoor use and in accordance with
Overvoltage Category II, Pollution Degree 2.
Category II includes local level, appliance,
portable equipment, etc., with transient
overvoltages less than Overvoltage Cat. III

6 38389 V2.6 10/03

Operation
NOTICES: Read and understand all warning and precaution
statements listed in the safety section of this operation manual prior to
using this meter. Set the function select switch to the OFF position
when the meter is not in use.
AC/DC Current Measurements
WARNING: Ensure that the test leads are
disconnected from the meter before making current No
clamp measurements.
1. Set the Function switch to the 600 or 400A
range. If the range of the measured is not
known, select the higher range first then move
to the lower range if necessary.
2. Select AC or DC with the AC/DC button. Press
the zero button to zero the meter in the DCA
mode only. Yes
3. Press the trigger to open jaw. Fully enclose
one conductor to be measured.
4. The clamp meter LCD will display the reading.
AC/DC Voltage Measurements
1. Insert the black test lead into the negative
COM terminal and the red test lead into the
positive V terminal.
2. Set the function switch to the V position.
3. Select AC or DC with the AC/DC button.
4. Connect the test leads in parallel to the circuit
under test.
5. Read the voltage measurement on the LCD
display.
V

7 38389 V2.6 10/03

Resistance and Continuity Measurements
1. Insert the black test lead into the negative COM terminal and the
red test lead into the positive terminal.
2. Set the function switch to the •))) Ω CAP position.
3. Use the multifunction button to select resistance.
4. Touch the test probe tips across the circuit or component under
test. It is best to disconnect one side of the device under test so the
rest of the circuit will not interfere with the resistance reading.
5. For Resistance tests, read the resistance on the LCD display.
6. For Continuity tests, if the resistance is < 30Ω, a tone will sound.

Capacitance Measurements
WARNING: To avoid electric shock, discharge the capacitor under test
before measuring.
1. Set the function switch to the •)))
Ω CAP Position.
2. Press the multifunction button to select the
capacitance function.
3. Insert the black test lead banana plug into
the negative (COM) jack and the red test
lead banana plug into the positive jack.
4. Touch the test probe tips across the part
under test.
5. Read the capacitance in the display.
6. The display will indicate the proper CAP
decimal point and value.

8 38389 V2.6 10/03

Temperature Measurements
WARNING: To avoid electric shock, disconnect both test probes from
any source of voltage before making a temperature measurement.
1. Set the function switch to TEMP.
2. Insert the Temperature Probe into the negative
(COM) and the positive jacks, making sure to
observe the correct polarity.
3. Touch the Temperature Probe head to the part
whose temperature you wish to measure. Keep
the probe touching the part under test until the
reading stabilizes (about 30 seconds).
4. Read the temperature in the display. The digital
reading will indicate the proper decimal point
and value.
WARNING: To avoid electric shock, be sure the
thermocouple has been removed before changing to
another measurement function
Data Hold
To freeze the LCD meter reading, press the data hold button. The data
hold button is located on the left side of the meter (top button). While
data hold is active, the DH display icon appears on the LCD. Press the
data hold button again to return to normal operation.
Peak Hold
To hold the highest reading on the LCD, press the peak hold button. The
peak hold button is located on the left side of the meter (bottom button).
The meter reading will not change as readings change, rather it will only
display the highest reading encountered since the peak hold button was
pressed. Press the peak hold button again to return to normal operation.

9 38389 V2.6 10/03

Maintenance
WARNING: To avoid electrical shock, disconnect the meter from any
circuit, remove the test leads from the input terminals and turn OFF the
meter before opening the case. Do not operate with open case.
Cleaning and Storage
Periodically wipe the case with a damp cloth and mild detergent; do not
use abrasives or solvents. If the meter is not to be used for periods of
longer than 60 days, remove the battery and store it separately
Battery Replacement
1. Remove the Phillips head screw that secures the battery door.
2. Open the battery compartment
3. Replace the 9V battery
4. Replace and secure the door.

Temperature Probe Replacement

The replacement bead wire probe with banana plug connectors is p/n
TP873.
The use type k probes with a mini plug connector requires a mini-plug to
banana plug converter (p/n 872000).

10 38389 V2.6 10/03

Warranty
EXTECH INSTRUMENTS CORPORATION warrants this instrument to be free of
defects in parts and workmanship for one year from date of shipment (a six month
limited warranty applies on sensors and cables). If it should become necessary to
return the instrument for service during or beyond the warranty period, contact the
Customer Service Department at (781) 890-7440 ext. 210 for authorization or visit our
website at www.extech.com (click on ‘Contact Extech’ and go to ‘Service Department’
to request an RA number). A Return Authorization (RA) number must be issued
before any product is returned to Extech. The sender is responsible for shipping
charges, freight, insurance and proper packaging to prevent damage in transit. This
warranty does not apply to defects resulting from action of the user such as misuse,
improper wiring, operation outside of specification, improper maintenance or repair, or
unauthorized modification. Extech specifically disclaims any implied warranties or
merchantability or fitness for a specific purpose and will not be liable for any direct,
indirect, incidental or consequential damages. Extech's total liability is limited to repair
or replacement of the product. The warranty set forth above is inclusive and no other
warranty, whether written or oral, is expressed or implied.
Repair and Calibration Services
Extech offers complete repair and calibration services for all Extech
products. For periodic calibration, NIST certification or repair of any
Extech product, call customer service for details on services available.
Extech recommends that calibration be performed on an annual basis to
ensure calibration integrity.

Tech Support Hotlines

781-890-7440 ext. 200
support@extech.com
www.extech.com

Copyright © 2002 Extech Instruments Corporation. All rights reserved

including the right of reproduction in whole or in part in any form.

11 38389 V2.6 10/03