The ETU-05-16/30 is a voice multiplexing device that (1) connects up to 32 external user lines to one E1 channel using time-division multiplexing, (2) has bidirectional call and data communication functions, and (3) can be remotely managed and maintained through a network administration system.
The ETU-05-16/30 is a voice multiplexing device that (1) connects up to 32 external user lines to one E1 channel using time-division multiplexing, (2) has bidirectional call and data communication functions, and (3) can be remotely managed and maintained through a network administration system.
The ETU-05-16/30 is a voice multiplexing device that (1) connects up to 32 external user lines to one E1 channel using time-division multiplexing, (2) has bidirectional call and data communication functions, and (3) can be remotely managed and maintained through a network administration system.
The ETU-05-16/30 is a voice multiplexing device that (1) connects up to 32 external user lines to one E1 channel using time-division multiplexing, (2) has bidirectional call and data communication functions, and (3) can be remotely managed and maintained through a network administration system.
Copyright:
Attribution Non-Commercial (BY-NC)
Available Formats
Download as PDF, TXT or read online from Scribd
Download as pdf or txt
You are on page 1/ 2
ETU-05-16/30
E1 Voice Multiplexer The physical representation of the ETU-05-16/ 30 voice multiplexing device is shown in the picture on the right. Utilizing advanced digital time-division TRNSMISSION
multiplexing technology, a single ETU-05-16/30
voice multiplexing device can connect up to 32 ex- ternal user lines with one E1 channel in a 1U stan- dard case. The unit can be cascaded to increase user capacity to realize seamless and smooth ex- pansion. The device has call in/call out bidirectional communication functions, user circuitry inverse cost counter func- tion and provides a data interface that can connect with a user data interface (V.35 or R350) for comprehensive access of voice and data. The E1 interface corresponds with ISDN PRI standard, D channel signaling interface corresponds with ISDN Q921/Q931 30B+D subset (Corresponds with GBYDN 034.1-034.4). This device has self-diagnostics and a remote maintenance function that can perform centralized remote surveillance, alarm, configuration, management and maintenance of all online ETU-05-16/30 voice multiplexing devices through a centralized network administrative system. Specifications This device corresponds with ISDN user-network interface regulation established by the original Ministry of Post and Telecommunication: YDN 034.1-1997 / YDN 034.2-1997 / YDN 034.3-1997 / YDN 034.4-1997 This device complies with the following related industrial standards for telephony exchanger network access examination of public telephony network: GB3378 (Telephony autoexchange network user signal mode) GB3380 (Telephony auto exchange network bell stream and signal tone) GB6879 (Technical specification of 2048KBIT/S 30 circuit impulse code modular multiplex device) GB/T5444 (User signal technical indices test method of telephony auto exchange network)
E1 Circuit E1 System Clock
Frame format: CCS(PCM31) Recovery clock: From E1 circuit receive signal Bit rate: 2.048Mb/s Internal clock: 2.048Mb/s+/-50ppm Line code: HDB3 Receive sensitivity: -20/-43dB User line interface Circuit: 75 ohm (non-balance) Line impedance: 600 ohm 120 ohm (balance) Feedback current: 25mA ¡ Pul se level: Standard 2.37V(75 ohm) Exterior line length: More than 4 Kms Range of Jitter tolerance: In accordance with ITU G.823, The exterior line interface has jitter attenuator installed electric line induction protection and lightening strike wave In accordance with protection function. ITU-recommendations: G.703, G.704, G.732, G.823 Bell stream parameter: Effective value 90V, 25Hz
Data Interface Supervision/counting interface Interface type V.35, RS-530 Protocol: RS-232 (DCE) Interface rate N x 64Kbps Rate: 9600bps Code type: N, 8, 1, no flow control System power supply AC supply: 220V+/-20%, 47~63Hz Physical indices DC supply: -48V+/-20% Case: 1U 19 inch standard case Power: < 50W Size ( H x W x D) 45 x 440 x 380 mm Weight: 2.5KG LED indication Working condition: Temp 0~40oC Alarm, Work, Power Humidity 0~90% (non condensing) Application
Ordering Information
ETU-05 Provides most 16/30 user exterior lines with one E1 channel, call in/call out bi-directional communica tion function, user circuitry inverse cost counter function, E1 I/F corresponds with ISDN PRI stan dard, self-diagnosis and remote maintenance function , datacom port for data transmitted (need optional adapter cables) and billing function
ETU-05-XX-XX
16 or 30 AC or DC 16: 16-ports AC: AC model 30: 30-ports DC: DC model Examples ETU-05-16-AC ETU-05, AC model, up to 16 channels voice multiplexing, with Dataport module ETU-05-30-DC ETU-05, DC model, up to 30 channels voice multiplexing, with Dataport module
