Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

TRANS WP29 GRSG 84 Inf16e

Download as pdf or txt
Download as pdf or txt
You are on page 1of 7

Informal document No.

16
(84th GRSG, 5-9 may 2003,
Agenda item 9)

National Regulations concerning Driver’s field of vision of immediate frontward


and sideward

Transmitted by the expert from JAPAN

1. Scope
These technical Regulations apply to the mirror and other devices pursuant paragraph 5 of Article 44 of the
Safety Regulations.
2. Definitions:
2.1. “Seating Reference Point” means point H (a hip joint of the dummy) of 3DH machine seated on the vehicle
seat in accordance with the seating arrangement set forth in IS0-6549-1980 or seated in the design standard
equivalent to ISO. In the case where seats have an adjustment mechanism to move them in a front/back or
up/down direction, to tilt a backrest or for other adjustment, the seats should be placed at the design standard
position.
2.2. “The driver’s ocular points” mean driver’ s ordinary eye points in an usual driving condition that passes a
point vertically 635mm above the Seating Reference Point (hereinafter referred to as a “Midpoint of reference
eye point”), and are also points that lie on a straight line perpendicular to a center plane of a vehicle, and are
symmetrically located 65mm to the right and left from the Midpoint of reference eye point (binocular). In this
case, the Midpoint of reference eye points is adjusted in Longitudinal or vertical directions by the distance
corresponding to the “back angle” of the test vehicle shown in Table 1.
2.3. “Back angle” means the backward-tilted angle of the body base line of a seated person that corresponds to
either the torso angle measured using a 3 DH machine defined in IS0-6549-1980 or corresponding to a design
standard angle equivalent to the said torso angle.
Table 1: Compensation of midpoint of reference eye points
Compensation Distance Back angles Compensation Distance
Back angles Longitudinal Vertical Longitudinal Vertical
(degrees)
(degrees) Direction Direction Direction Direction
mm mm mm mm
5 -186 28 23 -18 5
6 -177 27 24 -9 3
7 -167 27 25 0 0
8 -157 27 26 9 -3
9 -147 26 27 17 -5
10 -137 25 28 26 -8
11 -128 24 29 34 -11
12 -118 23 30 43 -14
13 -109 22 31 51 -18
14 -99 21 32 59 -21
15 -90 20 33 67 -24
16 -81 18 34 76 -28
17 -72 17 35 84 -32
18 -62 15 36 92 -35
19 -53 13 37 100 -39
20 -44 11 38 108 -43
21 -35 9 39 115 -48
22 -26 7 40 123 -52
Note: (Symbols in the above table) Longitudinal Direction ( "-" :frontward, "+": rearward)
Vertical Direction ( "-" :downward, "+": upward)

2.4. An “Obstacle” means a pole with a round cross-section with a 0.3m diameter and 1m height.
2.5. “The Mirror and other Devices” means the mirror and other devices described in paragraph 5 of Article 44 of
the Safety Regulations such as mirrors (including a direct left view mirror), cameras, visual display devices
and other devices that driver’s field of vision of immediate frontward and sideward.
2.6. “Cab-Over-Type Heavy Duty Trucks and So Forth” mean regular vehicles of which whose gross weight is not
less than 8 tons or maximum loading capacity is not less than 5 tons, and whose engines substantial part is
installed in or under the driver/passenger’ s cabin (excluding the vehicles whose passenger capacity is not less
than 11 or whose shapes resemble the vehicles carrying at least 11 passengers). “Cab-Over-Type Heavy Duty
Trucks and So Forth” do not include one-side cab vehicles of which engines are installed beside the driver’ s
cabin, and truck cranes of which engines are installed in/behind the driver/passenger’ s cabin.
2.7. “Test vehicle state” means the vehicles that is parked on a flat surface under empty conditions (fuels,
lubricants and coolants must be filled in engines and fueling devices, and the vehicle must be equipped with
fixed equipment for the normally required operation), accommodating a driver (55 kg) and a passenger (55
kg) on the seat next to the driver and on the side of the vehicle, or the vehicle in the equivalent state. The test
vehicles must be in the state of driving straight forward. The ground clearance must be adjusted to the design
standard value if the vehicles have a height adjustment mechanism.
2.8. A “Camera” means a device that takes photographs and visually display them whenever necessary for a driver
to see immediate frontward and sideward.
2.9. A “Visual Display Device” means a device which provides an image of direct front/left areas of the vehicle
through the camera.
3. General Requirements:
3.1. A mirror and other devices must meet the requirements set forth in 5.1. or 5.2. when tested with test
procedures defined in 4..
3.2. If the lowest point of parts extruding out of the external parts near the end of the vehicle 1.8 m or less above
the ground, such part must be designed to reduce impacts on pedestrians who may contact it, and meet the
requirements of the attached 64 “Technical Standard of Impact Reduction of inside Rearview Mirror”.
3.3. A mirror and other devices installed outside the vehicle must not extrude out of the vehicle more than 250 mm
(if such vehicle tows other vehicles that is wider than the towing vehicle, the length of the extrusion out of the
towed vehicle must be 250 mm or less).
3.4. In case that the camera and visual display devices are used to meet the requirements of the technical
Regulations, the camera and visual display devices must comply with the following requirements:
3.4.1. A visual display device must enable a driver at the driver’ s seat to easily obtain images through the
camera when an engine is operated and gears are in a neutral, drive or reverse position.
3.4.2. A visual display device that cannot display simultaneously entire vision that is not seen directly by the
driver or not reflected on a mirror should enable a driver to see such areas by adjusting the camera or
visual display device.
3.4.3. As far as a visual display device complies with 3.5.1. and 3.5.2., displayed images may be changed
without driver’ s operation.
3.5. A mirror and other devices of cab-over-type heavy duty trucks and so forth must meet the following
Regulations or other Regulations equivalent to them:.
3.5.1. The curvature radius of the mirror identifying the obstacle in the front area of the vehicle must be more
100 mm or longer.
3.5.2. The curvature radius of the mirror identifying the obstacle in the front/left areas of the vehicle must be
300 mm or longer.
3.5.3. The curvature radius of the mirror identifying the obstacle in the back/left areas of the vehicle must be
600 mm or longer.
4. Test Procedures:
4.1.A compact car, a light car and a regular car (excluding a cab-over-type heavy duty truck, a motorcycle, a
motorcycle with a sidecar, a tricar and a light car with caterpillars or sleds):
The device must recognize an obstacle (Figure1) located between the vehicle and vertical surface 0.3 m away
from an front and left-sides (for left-hand drive vehicles, on the right-side of the vehicle) of the test vehicle
directly from the reference eyepoints or from the midpoints of reference eye points with a rearview mirror or
with a mirror and other devices set forth in paragraph 5 of Article 44 of the Safety Standard. In this case, the
reference eye points or the midpoint of the reference eye points can be adjusted in accordance with 4.3..
4.2. Cab-over-type heavy duty trucks and so forth:
The device must recognize an obstacle (Figure2) located between the vehicle and vertical planes 2 m away
from front and 3 m away from the left-side (for left-hand drive vehicles, from the right-side of the vehicle) of
the test vehicle directly from the reference eye points or the midpoint of reference eye points with a rearview
mirror or a mirror and other devices set forth in paragraph 5 of Article 44 of the Safety Regulations. In this
case, the reference eye points or the midpoint of reference eye points can be adjusted in accordance with 4.3..
4.3.Compensation of displaced eye points
For the tests in accordance with 4.1. and 4.2. when a driver looks around the vehicle with movements in
longitudinal direction or vertical directions, the eye points (binocular) may be adjusted in longitudinal
direction or vertical directions from the midpoint of reference eye points as a measuring base point within the
range shown in the table 2.

Table 2: A Range of compensation of midpoints of Displaced Eye Points


Range of compention Range of compention
Range of compention
of Longitudinal of Lateral
of Vertical
(+:rearward (+:right -:left)
(+:upward -:downward)
-:frontward)

reference Eye Point 0 0 0

Upward displaced eye


0 -10 40
points
Frontward displaced
eye points -140 -15 10

Sideward displaced eye


points 30 -110 15

Note: In the above table, for left-hand drive vehicles,


“Right” should read “Left” and “Left” should read “Right”.
Figure 1 Figure 2

0.3 m
0.3 m

Vehicle
Vehicle

5. Criteria:
5.1.Criteria of the judgment for compact cars, light cars and regular cars (excluding cab-over-type heavy duty
trucks):
For test 4.1., at least a part of the obstacle defined in 4.1. must be recognized. An exceptional criterion is
permitted when the recognition is hindered by the followings:
5.1.1.Windshield wipers
5.1.2.A steering wheel
5.1.3.A -pillar or a part of an outside rearview mirror defined in Attachment 1
5.2.Criteria of the judgment for cab-over-type heavy duty trucks:
For test 4.2., at least a part of the obstacle defined in 4.2. must be recognized. The provision of 5.1. is also
applied in this case.
Annex 1
Range of Blind Spots Caused by A-Pillar or Outside Rearview Mirror

1. Definition:
1.1. The “Blind Spot by the Outside Rearview Mirror” means a blind spot caused by an outside rearview mirror or
by structures holding or protecting the said mirror.
1.2. A “Blind Spot by A-Pillar” means a blind spot caused by structures, lying above a plane parallel to the center
line of the vehicle and ahead of the reference eye points, that pass the midpoint of reference eye points and
the lowest point (point a) of the transparent side window in which a driver can recognize the ground through
the side window when checking the left side of the vehicle from the center of the standard eye points
(Figure3). However, the window partially placed in the lower part of the door is not considered as a side
window. For left-hand drive vehicles, “Left” should read “Right”.
2. Range of Blind Spot by A-Pillar or Outside Rearview Mirror
The range of blind spot by A-pillar or the outside rearview mirror defined in 5.1.3. must satisfy the following
condition: When there are several blind spots, each of them must meet the above condition.
X 0.292L 0.203
X (m): The boundary of the area thus excluded. The distance between the centers of the columns tangent
to the front end and the rear end of the blind spot.
L (m): The distance between the rear end of the column standing in a blind spot created by a A-pillar or
rearview mirror and tangent to the rear end of such blind spot and the front end of the rear wheel.

Figure 3 A blind spot by A pillar


A plane parallel
to the vehicle’s center line
passing through point a.

A blind spot by an
outside rearview
mirror

The lowest point (point a) of the transparent


side window in which a driver can recognize
the ground through the side window when
checking the left side of the vehicle from the
standard eye points.
Figure 4

Range of Visibility

The boundary of the


area thus excluded. The
distance between the
centers of the columns
tangent to the front end
and the rear end of the
blind spot: X(m)

Front Edge of Rear


Wheel
The distance between
the rear end of the
column standing in a
blind spot created by a
A-pillar or rearview
mirror and tangent to
the rear end of such
blind spot and the front
end of the rear wheel:
L(m)

You might also like