Saudi Aramco Inspection Checklist

SAUDI ARAMCO ID/PIEU - 25-Apr-2017 - REV. 2018.02.00 (Standards Cutoff -February 28, 2018) Rev. 2018.02.
00 28-Feb-18
SAIC NUMBER DATE APPROVED QR NUMBER
SAUDI ARAMCO INSPECTION CHECKLIST
Review Procedure - Tightening High Strength Bolts (ASTM
SAIC-M-2001 25-Apr-18 MECH-
A325)
PROJECT TITLE WBS / BI / JO NUMBER CONTRACTOR / SUBCONTRACTOR
EQUIPMENT ID NUMBER(S) EQUIPMENT DESCRIPTION EQPT CODE SYSTEM ID. PLANT NO.
LAYOUT DRAWING NUMBER REV. NO. PURCHASE ORDER NUMBER EC / PMCC / MCC NO.
SCHEDULED INSPECTION DATE & TIME ACTUAL INSPECTION DATE & TIME QUANTITY INSP. MH's SPENT TRAVEL TIME
SAUDI ARAMCO USE ONLY
SAUDI ARAMCO TIP NUMBER SAUDI ARAMCO ACTIVITY NUMBER WORK PERMIT REQUIRED?
SAUDI ARAMCO INSPECTION LEVEL CONTRACTOR INSPECTION LEVEL
ITEM
ACCEPTANCE CRITERIA REFERENCE PASS FAIL N/A RE-INSP DATE
No.
A General Requirements ... ASTM A 325 Bolting is primarily employed at SA. See Notes.
Procedure is identified and traceable to the project's updated list of quality

documents. Note: Detailed requirement for document ID shall be listed as Sch Q,
A1
addition or supplementary to this checkpoint upon approval of the Project Section 3
Document Control Procedure.
Procedure has identified the use of ASTM A325 N bolts for all primary SAES-M-001,
A2
structural connections. Para. 7.1.12.2
The procedure identified the type of joints (ie: snug-tightened joints, pre-
tensioned bolts, or slip-critical joints). 12-SAMSS-008,
A3 [PIP STS05130, Para. 6.5.1 and Bolted joints shall confirm the Sec. I & SAES-M-
requirements of latest edition of AISC Specification for Structural Joints 001 Para 7.1.12.3
Using ASTM A325 or A490 Bolts.
The procedure identified the requirements for the submission of the mill
certificates of the fastener materials (bolt, nuts and washers) to verify that
12-SAMSS-008,
A4 bolting components meet the ASTM Specification.
Sec. I
[PIP STS05130, Para. 6.5.1 and Specification for Structural Joints Using
ASTM A325 or A490 Bolts and contract documents.
Procedure identified the requirement for proper storage of bolting

components & conformed with requirements stated in Specification for 12-SAMSS-008,
A5
Structural Joints Using ASTM A325 or A490 Bolts, Para. 2.2. and PIP Sec. I
STS05130, Para. 6.1.1
It identified the general requirements for bolted part prior to bolting such
as:
a. Conditions of the connected plies. (para6)
12-SAMSS-008,
b. Conditions of the faying surfaces.(para 6)
Sec. I& 12-
A6 c. Conditions for bolt holes. (6.1.15)
SAMSS-007
d. Burrs (Para. 3.4,para 6.1.15)
Sec.6
e. Use of washers (Sec. 6)
[Refer to Specification for Structural Joints Using ASTM A325 or A490
Bolts for the corresponding paragraph numbers.]
Indicate the requirement & procedure to perform pre-installation

verification for joints that will be tighened using any pretensioning 12-SAMSS-008,
A7
methods. [PIP STS05130, Para. 6.5.1 and Specification for Structural Sec. I
Joints Using ASTM A325 or A490 Bolts, Section 7]
Procedure stated the installation requirements and method on how to

apply the tightening of bolted parts using the applicable method. 12-SAMSS-008,
A8
[PIP STS05130, Para. 6.5.1 and Specification for Structural Joints Using Sec. I
ASTM A325 or A490 Bolts, Section 8]
An effective marking system was included to mark high strength bolted

12-SAMSS-008,
A9 connections after tightening. (PIP STS05130, Para. 6.5.7)
Sec. I
Shall be easily understood & identifiable from grade.
ASTM A490/A490M Bolts & galvanised ASTM A 325/A325M Bolts shall PIP STS05130
A11
not be reused. Para 6.5.6
Mechanically galavanized bolts & nuts shall not be intermixed with hot dip PIP STS05130
A10
galavanized nuts & bolts . Para6.5.4
Saudi Aramco: Company General Use

Inspection tools & tool calibaration records for the tools used by the
PIP STS05130
A10 erector shall be mainatined & avaialble for the the examination by the
Para 4.1.9
buyer's inspector

SAUDI ARAMCO ID/PIEU - 25-Apr-2017 - REV. 2018.02.00 (Standards Cutoff -February 28, 2018) Rev. 2018.02.00 28-Feb-18
SAIC NUMBER DATE APPROVED QR NUMBER
SAUDI ARAMCO INSPECTION CHECKLIST
Review Procedure - Tightening High Strength Bolts (ASTM
SAIC-M-2001 25-Apr-18 MECH-
A325)
Attachment 1 - AISC SPEC FOR TIGHTENING ASTM A325 CONNECTIONS
Attachment 1 - AISC SPEC FOR TIGHTENING ASTM A325 CONNECTIONS

SA 12-SAMSS-007 BOLTING REQUIREMENTS, Section 4.6


Saudi Aramco Inspection Checklist

Uploaded by

Copyright:

Available Formats

Saudi Aramco Inspection Checklist

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Saudi Aramco Inspection Checklist

Uploaded by

Copyright:

Available Formats

SAUDI ARAMCO ID/PIEU - 25-Apr-2017 - REV. 2018.02.00 (Standards Cutoff -February 28, 2018) Rev. 2018.02.

SAUDI ARAMCO INSPECTION LEVEL CONTRACTOR INSPECTION LEVEL

Procedure is identified and traceable to the project's updated list of quality

Procedure identified the requirement for proper storage of bolting

Indicate the requirement & procedure to perform pre-installation

Procedure stated the installation requirements and method on how to

An effective marking system was included to mark high strength bolted

Saudi Aramco: Company General Use

Saudi Aramco: Company General Use

Attachment 1 - AISC SPEC FOR TIGHTENING ASTM A325 CONNECTIONS

Saudi Aramco: Company General Use

You might also like