CXA3822M: AC-DC Power Supply Secondary Controller IC

AC-DC Power Supply Secondary Controller IC
CXA3822M
Description
The CXA3822M is a secondary controller IC used for AC-DC power supply series resonance converter.
(Applications: Power supply circuits)
Features
< 5V, 12V control block >

 5V/12V voltage control circuit
 OTP (Detection of abnormal temperature) function
 LVP/OVP (Detection of abnormal voltage)
 Mode transition timer function
< Common >

 16-pin SOP package
 TSD protection function
 UVLO function
Structure
CMOS silicon monolithic IC
Sony reserves the right to change products and specifications without prior notice. This information does not convey any license
by any implication or otherwise under any patents or other right. Application circuits shown, if any, are typical examples illustrating
the operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits.
-1- E09X14
Free Datasheet http://www.datasheet4u.com/

CXA3822M
Absolute Maximum Ratings
Item Symbol Rating Unit Remarks

Maximum supply
VCC_12V 24 V VIN5, VIN12
voltage1
Maximum supply
VDD5 7.5 V VDD5
voltage2
12V pin voltage VCCIN –0.3 to +24 V AMPO12, AMPIN12, AMPO5, AMPIN5
TEST, TEMP, xACDC_STBY, xPFCOK,
VDD pin voltage VDDIN –0.3 to +7.5 V
xACDET, MAINON, LATCH5, ACIN_DET
Allowable power *1
Pd mW (See the thermal derating curve.)
dissipation
Operating ambient C
Topt –30 to +125 —
temperature range
Junction temperature Tjmax +150 C —
Storage temperature Tstg –55 to +150 C —
*1 Allowable power dissipation reduction characteristics
1000
Allowable power dissipation [mW]
When mounted on a four-layer board
800
When mounted on a one-layer board
600 578mW
400 334mW
200
60.2˚C 98.1˚C
–20 0 20 40 60 80 100 120 140 160
Operating ambient temperature Ta [˚C]
Glass fabric base epoxy board, 76mm × 114mm, t = 1.6mm
Recommended Operating Conditions
Item Symbol Rating Unit Remarks

Protection function operates outside of VIN12
Supply voltage1 VCC_12V 7.6 to 14.79 V
rating.
Protection function operates outside of VIN5
Supply voltage2 VCC_5V 3.8 to 6.12 V
rating.
Supply voltage3 VDD5 4.0 to 6.0 V VDD5
Operating ambient C
Topt –25 to +85 —
temperature range
Junction temperature Tj –25 to +125 C —
-2-
F r e e D a t a
CXA3822M
Block Diagram
12V_control circuit 5V_control circuit

AMPO12 3 14 AMPO5
VIN12 6 16 VIN5
VIN12 REG VIN5 REG
AMPIN12 4 13 AMPIN5
BGR_VIN5
GND12 5 15 GND5
Reference GND: GND12 Reference GND: GND12
1 VDD5
12V_NG detection circuit
Reference circuit
VIN12 LVP
LVP BGR_VDD5
UVLO_VDD5
VIN12 OVP
OVP TSD
OSC
Reference GND: GND12 Reference GND: GND12
VDD5
60kΩ
xACDC_STBY 12
240kΩ VIN5 LVP
LVP
VDD5
VIN5 OVP
60kΩ OVP
Control logic
xACDET 10
240kΩ
Reference GND: GND12
VDD5
10kΩ
MAIN_ON 9
Temperature detection circuit
VDD5
VDD5
TEMP OTP
10kΩ
2 TEMP
LATCH5 8 OTP
300kΩ
TEMP LVP
LVP 7 TEST
ACIN_DET 11 Reference GND: GND12

Logic GND: GND12
-3-

CXA3822M
Pin Configuration
VDD5 1 16 VIN5
TEMP 2 15 GND5
AMPO12 3 14 AMPO5
AMPIN12 4 13 AMPIN5
Top View
GND12 5 12 xACDC_STBY
VIN12 6 11 ACIN_DET
TEST 7 10 xACDET
LATCH5 8 9 MAINON
-4-

CXA3822M
Pin Table
Pin No. Pin name IN/OUT Function

1 VDD5 — VDD power supply output
2 TEMP IN Temperature monitor input for overheat protection
3 AMPO12 OUT 12V control output
4 AMPIN12 IN 12V control input
5 GND12 — 12V control GND, Internal reference GND, Logic GND
6 VIN12 — 12V input
7 TEST — NC
8 LATCH5 OUT Signal for latch stop of 5V output
9 MAINON OUT Power supply main 12V output ON/OFF signal
10 xACDET IN AC/+B detection signal from power supply upstream
11 ACIN_DET OUT AC detection signal
12 xACDC_STBY IN ON/standby switching signal for power supply (12V)
13 AMPIN5 IN 5V control input
14 AMPO5 OUT 5V control output
15 GND5 — GND for 5V control
16 VIN5 — 5V input
Input logic
Input signal L H
Standby mode Operating mode
xACDC_STBY
(12V = OFF) (12V = ON)
xACDET No upstream AC Upstream AC
Output logic
Output signal L H
MAINON Main output ON Main output OFF
ACIN_DET Abnormal (No AC) Normal (AC)
LATCH5 Abnormal (5V off latch) Normal
-5-

CXA3822M
Pin Description
Pin Standard
Symbol I/O Equivalent circuit Description
No. pin voltage
1 VDD5 — — — VDD power supply input
VDD5
GND to Temperature monitor input for

2 TEMP I
VDD5 2 overheat protection
GND12
VIN12
GND to
3 AMPO12 O 12V control output
VIN12 3
GND12
VIN12
GND to
4 AMPIN12 I 12V control input
VIN12 4
GND12
5 GND12 — — — GND for 12V control

6 VIN12 — — — 12V input
7 TEST — — — NC
VDD5
Signal for latch stop of 5V
8 LATCH5
output
GND to
O
VDD5 8
9
Power supply main 12V output
9 MAINON
ON/OFF signal
GND12
-6-

CXA3822M
Pin Standard
Symbol I/O Equivalent circuit Description
No. pin voltage
VDD5
GND to AC/+B detection signal from

10 xACDET I
VDD5 power supply upstream
10
GND12
VDD5
GND to
11 ACIN_DET O AC detection signal
VDD5 11
GND12
VDD5
GND to ON/standby switching signal

12 xACDC_STBY I
VDD5 12 for power supply (ACDC)
GND12
VIN5
VDD5
GND to
13 AMPIN5 I 5V control input
VIN5 13
GND5
GND12
VDD5
GND to 14
14 AMPO5 O 5V control output
VIN5 15
16
GND12
15 GND5 — — — GND for 5V control

16 VIN5 — — — 5V input
-7-

CXA3822M
Electrical Characteristics
Circuit current
(Unless otherwise specified, the conditions are VIN5 = 5.5V, VDD5 = 5.0V, VIN12 = 12V, Ta = 25C)
Item Symbol Conditions Min. Typ. Max. Unit

Power supply: VIN5, VDD5
Standby current ISTBY1 — 0.7 1.0 mA
xACDC_STBY = L (12V = OFF)
Power supply: VIN5, VDD5
Operating current1 ICC1 — 1.7 3.0 mA
xACDC_STBY = H (12V = ON)
Power supply: VIN12
Operating current2 ICC2 — 0.2 0.4 mA
xACDC_STBY = H (12V = ON)
Note) Co indicates capacitance connected to OUT pin.
Logic pin

Logic pin
VIH xACDC_STBY, xACDET pin 2.0 — VDD V
Input High voltage
Logic pin
VIL xACDC_STBY, xACDET pin 0 — 0.5 V
Input Low voltage
Logic input xACDC_STB, xACDET pin
IIN1 10 17 25 A
Inflow current1 VIN = 5V
Logic output High VDD –
VOH ACIN_DET, Io = –5mA — VDD V
voltage 0.3
Logic output Low
VOL ACIN_DET, Io = 5mA 0 — 0.3 V
voltage
Output voltage during
Io = 5mA
Low VLI — — 0.3 V
MAINON, LATCH5 pin
(Open drain pin)
Logic output High
ROH ACIN_DET, Io = –5mA 0 15 60 
side on resistance
Logic output Low side
ROL1 ACIN_DET, Io = 5mA 0 15 60 
on resistance
Output on resistance
Io = 5mA
during Low ROL2 0 15 60 
MAINON, LATCH5 pin
(Open drain pin)
-8-

CXA3822M
5V,12V control block


Voltage between VIN5
5V control voltage V5 and GND5 5.47 5.53 5.59 V
VDD5 = 4 to 6V
5V input LVP detection
LVP5 and GND5 3.8 4.0 4.2 V
voltage
VDD5 = 4 to 6V
5V input OVP detection
OVP5 and GND5 5.88 6.0 6.12 V
voltage
VDD5 = 4 to 6V
AMPO5 output voltage
VLI_5V Io = 5mA — — 0.3 V
during Low
12V control voltage V12 and GND12 11.88 12 12.12 V
VDD5 = 4 to 6V
12V input LVP detection
LVP12 and GND12 7.6 8 8.4 V
voltage
VDD5 = 4 to 6V
12V input OVP detection
OVP12 and GND12 14.21 14.5 14.79 V
voltage
VDD5 = 4 to 6V
AMPO12 output voltage
VLI_12V Io = 5mA — — 0.3 V
during Low
Temperature abnormality OTP = TEMP/VDD
OTP 0.68 0.692 0.704 —
detection ratio *1 VDD5 = 4 to 6V
TEMP pin LVP detection LTP — 0.05 0.1 0.2 V
VDD5 operation start
ACT_VDD VDD5 = L  H 3.1 3.3 3.5 V
voltage
VDD5 operation stop
UVLO_VDD VDD5 = H  L 2.5 2.7 2.9 V
voltage
HYS_VDD =
Hysteresis width HYS_VDD 0.2 0.5 1.0 V
ACT_VDD – UVLO_VDD
*1 Detects temperature abnormality when TEMP/VDD5  0.692.

Example of calculation: Detects temperature abnormality when TEMP/VDD5 = TEMP/5V  0.692,
that is TEMP  0.692  5 = 3.46V.
-9-

CXA3822M
Description of Operation
1. 5V Control Circuit and 12V Control Circuit

Fig.1 shows the equivalent circuit for the 5V and 12V control block.
When the VIN5 voltage exceeds 5.5V, the internal AMP output switches and current is drawn from AMPO5.
This enables control of VIN5 at 5.5V in combination with the primary side via a photocoupler connected to the
AMPO5 pin.
The 12V control operates in like manner; current is drawn from the AMPO12 pin when the VIN12 voltage
exceeds 12V.
This enables control of VIN12 at 12V in combination with the primary side via a photocoupler connected to
AMPO12.
5V and 12V control block
5V control circuit
AMPO5
22
VIN5
5VSB 24
22.5kΩ
VIN5 REG
AMPIN5
21
1V
5kΩ
5VSB REG
12V control circuit

AMPO12
3
VIN12
VIN12 6
55kΩ
VIN12 REG
AMPIN12
4
1V
5kΩ
12V REG
Fig.1. 5V and 12V Control Equivalent Circuit
- 10 -

CXA3822M
2. 5V and 12V Control Abnormality Detection

Fig.2 shows the equivalent circuits for the 5V and 12V control voltage abnormality detection block.
When an abnormal 5V and 12V control REG voltage occurs during operation, the device detects the
abnormality and transitions to the “latch stop” state. (For the states following abnormality detection, see the
state transition diagram on page 19.)
The abnormality detection voltages are as follows.
5V control abnormality detection------- LVP: 4V or lower

OVP: 6V or higher
12V control abnormality detection------ LVP: 8V or lower

OVP: 14.5V or higher
5V and 12V control voltage abnormality detection block
VIN5
5VSB 24
VIN5 LVP
(4V detection)
LVP
VIN5 OVP
(6V detection)
OVP
Control logic
VIN12
VIN12 6
VIN12 LVP
(8V detection)
LVP
VIN12 OVP
(14.5V detection)
OVP
Fig.2. 5V and 12V Control Abnormality Detection Equivalent Circuit
- 11 -

CXA3822M
3. Temperature Abnormality Detection Circuit

Fig.3 shows the equivalent circuit for the temperature abnormality detection block.
As shown in the figure, a thermistor connected between the TEMP and VDD5 pins enables detection of
abnormal board temperatures. A temperature error is detected when the voltage ratio of the TEMP and VDD5
pins is 0.692 or more (TEMP/VDD5  0.692).
A temperature abnormality is defined when the abnormal temperature continues for 1.1 seconds.
When a temperature abnormality is detected, the device transitions to the “abnormality detection” or “latch
stop” state.
(For the states following abnormality detection, see the state transition diagram on page 14.)
In addition, as a pin protection function, the same abnormality is detected when the voltage of the TEMP pins
falls to 0.1V or lower.
Temperature abnormality detection block
VDD5
VDD5 Thermistor
TEMP OTP
(70 ˚C detection) TEMP
2
OTP
Control logic 300kΩ
TEMP LVP
(0.1V detection)
LVP
Fig.3. Temperature Abnormality Detection Equivalent Circuit
- 12 -

CXA3822M
5. State Transition Diagram

Fig.4 shows a state transition diagram (main state).
Transitions between states occur in response to input signals from external sources or the condition of the 5V
and 12V outputs.
Input signal defined time
Input signal Defined time

xACDC_STBT 2.2ms × 5 times
xACDET 4.4µs × 5 times
TEMP_OTP 144ms × 8 times
TEMP_LTP 141µs × 5 times
Initialization ANY
12VIN_OVP 35µs × 5 times
MAIN_ON = H SYS_RST = H (∗1) MAIN_ON = ∗
ACIN_DET = L ACIN_DET = ∗ 12VIN_LVP 35µs × 5 times
(Non-synchronous reset) LATCH5 = ∗
LATCH5 = H 5VIN_OVP 35µs × 5 times
5VIN_LVP 35µs × 5 times
OVP5 VIN5
SYS_RST = L (∗1) SYS_RST Immediately
& 110ms elapsed [xACDET = L] & 110ms elapsed
[VIN5 LVP5]
or [OVP5 VIN5]
Standby or [TEMP LTP] AC recovery 2 5V latch stop
[VIN5 LVP5]
or [OTP TEMP] 550ms
MAIN_ON = H MAIN_ON = H or [OVP5 VIN5] MAIN_ON = H
elapsed
ACIN_DET = H ACIN_DET = L ACIN_DET = L
LATCH5 = H LATCH5 = H LATCH5 = L
xACDC_STBY = H
xACDC_STBY = L
55ms elapsed
AC recovery 1
12V start
MAIN_ON = H Within dotted line:
MAIN_ON = L OVP12 VIN12 ACIN_DET = L OVP5 VIN5 T1 count enabled
ACIN_DET = H LATCH5 = H OVP12 VIN12
LATCH5 = H [VIN5 LVP5]
or [OVP5 VIN5]
[xACDET = L] [xACDET = H] T1 count-up

(550ms elapsed)
550ms elapsed
12V latch stop
AC off OVP5 VIN5
MAIN_ON = H
OVP12 VIN12
MAIN_ON = H ACIN_DET = L
[44ms elapsed with xACDET = L] ACIN_DET = L LATCH5 = H
LATCH5 = H
[VIN12 LVP12]
55ms elapsed or [OVP12 VIN12]
Normal operation
Error detection
[VIN12 LVP12]
MAIN_ON = L or [OVP12 VIN12] MAIN_ON = L
ACIN_DET = H ACIN_DET = L
LATCH5 = H LATCH5 = H
xACDET = L
[VIN5 LVP5] or [OVP5 VIN5]
[TEMP LTP5] or [OTP TEMP]
Fig.4. State Transition Diagram
Input Signal Descriptions
Input signal
No. Signal description
name
Reset signal based on logic power supply (VDD5 pin)
*1 SYS_RST
High: Reset (VDD5  2.7V), Low: Reset canceled (VDD5  3.3V)
- 13 -

CXA3822M
AC Off Timing Chart

When AC input stops while in the “standby” or “12V start” state, the device transitions to the “AC off” state after
a minimum of 44ms has elapsed.
The conditions for a transition from the “standby” or “12V start” state to the “AC off” state are as follows:
Conditions for transition to “AC off”: xACDET = Low for 44ms duration
When the AC input returns within 44ms, no transition to the “AC off” state occurs and the current state is
maintained.
A timing chart for the transition from “standby” to “AC off” is shown below.
Transition from "standby" or "12V start" to “AC Off”
AC off
AC input
44ms 44ms
Device xACDET
input signals
MAIN_ON
Device ACIN_DET = H → L
output signals due to transition to AC off state
ACIN_DET
[xACDET = L for 44ms duration]
→ Transition to AC off state
Main state Standby or 12V start AC off
A timing chart for the transition from “normal operation” to “AC off” is shown below.
When AC input stops while in a state other than “standby” or “12V start,” the transition to the “AC off” state
occurs the moment the xACDET pin goes Low, regardless of whether or not 44ms have elapsed.
Transition from “Normal Operation” to “AC Off”
AC off
AC input
Device
xACDET
input signals
MAIN_ON
Device
output signals ACIN_DET = H → L
due to transition to AC off state
ACIN_DET
[xACDET = L]
→ Transition to AC off state
Main state Normal operation AC off
- 14 -

CXA3822M
Start Timing Chart

Fig.5 shows a timing chart for the start of operation.
The device is in the “initialization” state until 110ms have elapsed after the rising edge of VIN5 and VDD5
exceeds 3.3V.
In the “initialization” state, 5V LVP detection, temperature detection, and AC off detection are all disabled as
the device waits for 5V supply to start. After this, it transitions to the “standby” state and waits for the 12V start
instruction (xACDC_STBY) from the system. Abnormal voltage detection, temperature detection, and AC off
detection are enabled from the “standby” state onward.
When the 12V start instruction is received, the device enters the “12V start”, 12V abnormal voltage detection
is disabled for a maximum of 550ms. After that, if tha the device enters the “normal operation” state 12V
abnormal voltage detection is enabled.
AC input
VIN12
VDD5 UVLO canceled

(VDD5 ≥ 3.3V)
VIN5 12V start instruction

from system
xACDC_STBY
Device input signals
xACDET
Transition to 12V start state
when xACDC_STBY = H
MAIN_ON = H → L
MAIN_ON
ACIN_DET = L → H
ACIN_DET due to transition to standby
Device output signals
LATCH5
2.2ms × 5 times 55ms
550ms timer start
110ms Max. 550ms
Main state Initialization Standby 12V start Normal operation
5V_LVP Disabled Enabled Enabled Enabled
5V_OVP Enabled Enabled Enabled Enabled
12V_LVP Disabled Disabled Disabled Enabled
Protection functions 12V_OVP Disabled Disabled Enabled Enabled
xACDET Enabled Enabled Enabled Enabled

(AC on/off)
Disabled Enabled Enabled Enabled

TEMP OTP LTP
Fig.5. Start Timing Chart
- 15 -

CXA3822M
Stop Timing Chart 1

Fig.6 shows a timing chart for the transition from “normal operation” to “latch stop”.
When a 12V stop instruction (xACDC_STBY = L) is received from the system during normal operation, the
device transitions to the “standby” approximately 11ms later.
In the “standby” state 12V LVP and OVP detection are disabled.
When AC input stops while in “standby”, input from the primary side causes the xACDET pin to change from
High to Low, and the device enters the “AC off” state 44ms later. When in the “AC off” state, 5V LVP detection
is disabled.
With no AC input, the device enters the ANY state (reset condition) when 5V input drops and VDD  2.7V.
AC off
AC input
VIN12
VIN5 12V stop instruction VDD = 2.7V

from system
Transition to ANY state when VDD ≤ 2.7V
All protection functions disabled (reset condition)
xACDC_STBY
2.2ms × 5 times
Device input signals Input from primary
side due to AC off
xACDET = H → L
xACDET
Transition to standby state

when xACDC_STBY = L
MAIN_ON MAIN_ON = L → H
ACIN_DET = H → L
due to AC off
Device output signals ACIN_DET
44ms
LATCH5
Main state Normal operation Standby AC off Initialization
5V_LVP Enabled Enabled Disabled Disabled
5V_OVP Enabled Enabled Enabled Enabled
12V_LVP Enabled Disabled Disabled Disabled
12V_OVP Enabled Disabled Enabled Disabled

Protection functions
xACDET Enabled Enabled Enabled Enabled
(AC on/off)
TEMP OTP LTP Enabled Enabled Disabled Disabled
Fig.6. Stop Timing Chart 1
- 16 -

CXA3822M
Stop Timing Chart 2

Fig.7 shows a timing chart for the transition from “AC off” to “stop” in the “normal operation” state.
When AC input stops while in “normal operation”, input from the primary side causes the xACDET pin to
change from High to Low, and the device enters the “AC off” state. When in the “AC off” state, 5V LVP detection
is disabled.
With no AC input, the device enters the ANY state (reset condition) when 5V input drops and VDD  2.7V.
AC off
AC input
VIN12
Transition to ANY state when VDD ≤ 2.7V

All protection functions disabled (reset condition)
VIN5
VDD = 2.7V
xACDC_STBY
Input from primary

Device input signals side due to AC off
xACDET = H → L
xACDET
MAIN_ON = L → H
due to AC off
MAIN_ON
ACIN_DET = H → L
ACIN_DET due to AC off
LATCH5
Main state Normal operation AC off Initialization
5V_LVP Enabled Disabled Disabled
5V_OVP Enabled Enabled Enabled
12V_OVP Enabled Enabled Disabled

xACDET Enabled Enabled Enabled
(AC on/off)
TEMP OTP LTP Enabled Disabled Disabled
Fig.7. Stop Timing Chart 2
- 17 -

CXA3822M
Emergency Stop Timing Chart 1

Fig.8 shows a timing chart for a temperature abnormality during “normal operation”.
When a temperature abnormality occurs while in the “normal operation” state, the device transitions to the
“error detection” state, then 55ms later to “12V latch stop” and 550ms later to “5V latch stop”.
12V off at
LATCH12 = L
VIN12
5V off at
LATCH5 = L
VIN5
xACDC_STBY
xACDET
MAIN_ON = L → H
at transition to 12V latch stop state
MAIN_ON
ACIN_DET = H → L
at transition to error detection state
ACIN_DET
LATCH5 = H → L
LATCH5 at transition to 5V latch stop state
550 ms and 55 ms
timer start
550ms
Temperature error (1.1s elapsed)
55ms
Main state Normal operation Error detection 12V latch stop 5V latch stop
5V_LVP Enabled Enabled Enabled Disabled
5V_OVP Enabled Enabled Enabled Disabled
12V_LVP Enabled Enabled Disabled Disabled
Enabled Enabled Disabled Disabled

Protection functions 12V_OVP
xACDET Enabled Disabled Disabled Disabled
(AC on/off)
TEMP OTP LTP Enabled Disabled Disabled Disabled
Fig.8. Temperature Abnormality during 12V Operation
- 18 -

CXA3822M

Fig.9 shows a timing chart when detecting 12V voltage abnormality during “normal operation”.
When 12V voltage abnormality occurs while in the “normal operation” state, the device transitions to the “12V
latch stop” state, then 550ms later to “5V latch stop”.
12V off at
VIN12 LATCH12 = L
5V off at
LATCH5 = L
VIN5
xACDC_STBY
xACDET
MAIN_ON = L → H
MAIN_ON
ACIN_DET = H → L
ACIN_DET
LATCH5 = H → L
LATCH5
550ms timer start
550ms
12V error voltage detection
Main state Normal operation 12V latch stop 5V latch stop
5V_LVP Enabled Enabled Disabled
5V_OVP Enabled Enabled Disabled
12V_OVP Enabled Disabled Disabled

xACDET
Enabled Disabled Disabled
(AC on/off)
TEMP OTP LTP Enabled Disabled Disabled
Fig.9. 12V Voltage Abnormality during 12V Operation
- 19 -

CXA3822M

Fig.10 shows a timing chart when detecting 5V voltage abnormality during “normal operation”.
When 5V voltage abnormality occurs while in the “normal operation” state, the device transitions to the “5V
latch stop” state.
12V off at
VIN12 LATCH12 = L
5V off at
VIN5 LATCH5 = L
xACDC_STBY
xACDET
MAIN_ON = L → H
MAIN_ON
ACIN_DET = H → L
ACIN_DET
LATCH5 = H → L
LATCH5
Main state Normal operation 5V latch stop
5V_LVP Enabled Disabled
5V_OVP Enabled Disabled
Protection functions 12V_OVP Enabled Disabled
xACDET
Enabled Disabled
(AC on/off)
TEMP OTP LTP Enabled Disabled
Fig.10. 5V Voltage Abnormality during 12V Operation
- 20 -

CXA3822M

Fig.11 shows a timing chart when detecting 5V voltage abnormality or temperature abnormality during
“standby”.
When 5V voltage abnormality or temperature abnormality occurs while in the “standby” state, the device
transitions to the “5V latch stop” state.
5V off at
VIN5 LATCH5 = L
xACDC_STBY

xACDET
MAIN_ON
ACIN_DET = H → L
ACIN_DET
LATCH5 = H → L
LATCH5
Main state Standby 5V latch stop
5V_OVP Enabled Disabled
12V_LVP Disabled Disabled
12V_OVP Disabled Disabled

xACDET
Enabled Disabled
(AC on/off)
TEMP OTP LTP Enabled Disabled
Fig.11. 5V Voltage Abnormality or Temperature Abnormality during Standby
- 21 -

CXA3822M
AC Return Timing Chart 1

Fig.162 shows a timing chart for the period from AC off to return during “normal operation”.
When primary side AC input stops while in the “normal operation” state, the xACDET pin, which is the
secondary side input, goes Low and the device transitions to the “AC off” state. (See page 15 for details.)
When AC input subsequently returns, the device transitions to the “AC return 1” state for 55ms, then to the “AC
return 2” state for 550ms, and finally enters the “standby” state. If an AC off condition is detected while in an
“AC return” state, the device again transitions to the “AC off” state.
AC return
AC input
VIN12
VIN5
VIN5 drop due
to AC off
xACDC_STBY Input change due to AC off

Device input signals xACDET = L → H
xACDET Input change due to AC return

xACDET = L → H
MAIN_ON = H → L
due to transition to 12V start state
MAIN_ON MAIN_ON = L → H
due to transition to AC off state
ACIN_DET = L → H
Device output signals ACIN_DET = H → L due to transition to standby state
ACIN_DET due to transition to AC off state
LATCH5
55ms 550ms 2.2ms × 5 times 550ms
Main state Normal operation AC off AC return 1 AC return 2 Standby 12V start Normal operation
5V_LVP Enabled Disabled Disabled Enabled Enabled Enabled Enabled
5V_OVP Enabled Enabled Enabled Enabled Enabled Enabled Enabled
12V_LVP Enabled Disabled Disabled Disabled Disabled Disabled Enabled
12V_OVP Enabled Enabled Enabled Disabled Disabled Enabled Enabled

xACDET
Enabled Enabled Enabled Enabled Enabled Enabled Enabled
(AC on/off)
TEMP OTP LTP Enabled Disabled Disabled Disabled Enabled Enabled Enabled
Fig.12. AC Off to Return during 12V Normal Operation
- 22 -

CXA3822M
AC Return Timing Chart 2

Fig.13 shows a timing chart for the period from AC off to return during “standby”.
When primary side AC input stops while in the “standby” state, the xACDET pin, which is the secondary side
input, goes Low and the device transitions to the “AC off” state. (See page 15 for details.)
When AC input subsequently returns, the device transitions to the “AC return 1” state for 55ms, then to the “AC
return 2” state for 550ms, and finally enters the “standby” state. If an AC off condition is detected while in an
“AC return” state, the device again transitions to the “AC off” state.
AC return
AC input
VIN5
VIN5 drop due

to AC off
xACDC_STBY
Input change due to AC off
Device input signals xACDET = L → H
xACDET Input change due to AC return

xACDET = L → H
MAIN_ON
ACIN_DET = H → L ACIN_DET = L → H
due to transition to AC off state due to transition to standby state
Device output signals ACIN_DET
44ms
LATCH5
55ms 550ms
Main state Standby AC off AC return 1 AC return 2 Standby
5V_LVP Enabled Disabled Disabled Enabled Enabled
5V_OVP Enabled Enabled Enabled Enabled Enabled
12V_LVP Enabled Disabled Disabled Disabled Disabled
12V_OVP Enabled Enabled Enabled Disabled Disabled

xACDET
Enabled Enabled Enabled Enabled Enabled
(AC on/off)
TEMP OTP LTP Enabled Disabled Disabled Disabled Enabled
Fig.13. AC Off to Return during Standby
- 23 -

CXA3822M
Application Circuit
12V_control circuit 5V_control circuit AMPO5

AMPO12
3 14
VIN12 VIN5
VIN12 6 16 5VSB
VIN12 REG VIN5 REG
AMPIN12
4 13
AMPIN5
GND12 BGR_VIN5
5 GND5
15
Reference GND : GND12 Reference GND:GND12 5VSB REG
1
12V_NG detection circuit VDD5 2.2µF
VIN12 LVP Reference circuit
LVP BGR_VDD5
UVLO_VDD5
VIN12 OVP
OVP TSD
OSC
Reference GND : GND12 Reference GND : GND12
VDD5
60kΩ 5V_NG detection circuit

xACDC_STBY
ACDC_STBY 12
VDD5 240kΩ VIN5 LVP
LVP
VDD5
VIN5 OVP
60kΩ Control logic OVP
xACDET
AC_DETOUT 10
240kΩ
Reference GND : GND12
VDD5
ON/OFF 10kΩ
(MAIN_ON) MAIN_ON
9
VDD5 Thermistor
VDD5
TEMP OTP
5VSB Latch 10kΩ TEMP
LATCH5 2
8 OTP
300kΩ
TEMP LVP
TEST
LVP 7
ACIN_DET Reference GND : GND12

ACIN_DET 11
Logic GND:GND12
Application circuits shown are typical examples illustrating the operation of the devices. Sony cannot assume responsibility for
any problems arising out of the use of these circuits or for any infringement of third party patent and other right due to same.
- 24 -

CXA3822M
Package Outline
(Unit: mm)
16PIN SOP (PLASTIC)
+ 0.4 + 0.4
9.9 – 0.1 1.85 – 0.15
16 9
0.15
+ 0.2
0.1 – 0.05
5.3 – 0.1
+ 0.3
7.9 ± 0.4
6.9
1 8
0.5 ± 0.2
+ 0.1
0.45 ± 0.1 1.27 0.2 – 0.05
0.24 M
PACKAGE STRUCTURE
PACKAGE MATERIAL EPOXY RESIN
SONY CODE SOP-16P-L01
LEAD TREATMENT SOLDER PLATING
EIAJ CODE SOP016-P-0300
LEAD MATERIAL COPPER ALLOY
JEDEC CODE
PACKAGE MASS 0.2g
LEAD PLATING SPECIFICATIONS
ITEM SPEC.
LEAD MATERIAL COPPER ALLOY
SOLDER COMPOSITION Sn-Bi Bi:1-4wt%
PLATING THICKNESS 5-18µm
- 25 - Sony Corporation

CXA3822M: AC-DC Power Supply Secondary Controller IC

Uploaded by

Copyright:

Available Formats

CXA3822M: AC-DC Power Supply Secondary Controller IC

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

CXA3822M: AC-DC Power Supply Secondary Controller IC

Uploaded by

Copyright:

Available Formats

AC-DC Power Supply Secondary Controller IC

< 5V, 12V control block >

< Common >

CMOS silicon monolithic IC

Free Datasheet http://www.datasheet4u.com/

Absolute Maximum Ratings

Item Symbol Rating Unit Remarks

*1 Allowable power dissipation reduction characteristics

When mounted on a four-layer board

–20 0 20 40 60 80 100 120 140 160

Operating ambient temperature Ta [˚C]

Glass fabric base epoxy board, 76mm × 114mm, t = 1.6mm

Recommended Operating Conditions

Item Symbol Rating Unit Remarks

12V_control circuit 5V_control circuit

ACIN_DET 11 Reference GND: GND12

Free Datasheet http://www.datasheet4u.com/

Free Datasheet http://www.datasheet4u.com/

Pin No. Pin name IN/OUT Function

Free Datasheet http://www.datasheet4u.com/

GND to Temperature monitor input for

5 GND12 — — — GND for 12V control

Free Datasheet http://www.datasheet4u.com/

GND to AC/+B detection signal from

GND to ON/standby switching signal

15 GND5 — — — GND for 5V control

Free Datasheet http://www.datasheet4u.com/

Item Symbol Conditions Min. Typ. Max. Unit

Note) Co indicates capacitance connected to OUT pin.

Item Symbol Conditions Min. Typ. Max. Unit

Free Datasheet http://www.datasheet4u.com/

5V,12V control block

Item Symbol Conditions Min. Typ. Max. Unit

*1 Detects temperature abnormality when TEMP/VDD5  0.692.

Free Datasheet http://www.datasheet4u.com/

1. 5V Control Circuit and 12V Control Circuit

5V and 12V control block

12V control circuit

Fig.1. 5V and 12V Control Equivalent Circuit

Free Datasheet http://www.datasheet4u.com/

2. 5V and 12V Control Abnormality Detection

5V control abnormality detection------- LVP: 4V or lower

12V control abnormality detection------ LVP: 8V or lower

5V and 12V control voltage abnormality detection block

Fig.2. 5V and 12V Control Abnormality Detection Equivalent Circuit

Free Datasheet http://www.datasheet4u.com/

3. Temperature Abnormality Detection Circuit

Temperature abnormality detection block

Control logic 300kΩ

Fig.3. Temperature Abnormality Detection Equivalent Circuit

Free Datasheet http://www.datasheet4u.com/

5. State Transition Diagram

Input signal defined time

Input signal Defined time

[xACDET = L] [xACDET = H] T1 count-up

[VIN5 LVP5] or [OVP5 VIN5]

[TEMP LTP5] or [OTP TEMP]

Fig.4. State Transition Diagram