Data Sheet: TSA5520 TSA5521
Data Sheet: TSA5520 TSA5521
DATA SHEET
TSA5520; TSA5521
1.3 GHz universal bus-controlled
TV synthesizer
Product specification 1996 Oct 10
Supersedes data of 1995 Mar 16
File under Integrated Circuits, IC02
Philips Semiconductors Product specification
FEATURES
• Complete 1.3 GHz single chip system
• Four PNP band switch buffers (40 mA)
• 33 V output tuning voltage
• In-lock detector
• 15-bit programmable divider
APPLICATIONS
• Programmable reference divider ratio
(512, 640 or 1024) • TV tuners and front ends
ORDERING INFORMATION
PACKAGE
TYPE NUMBER
NAME DESCRIPTION VERSION
TSA5520M SSOP16 plastic shrink small outline package; 16 leads; body width 4.4 mm SOT369-1
TSA5520T SO16 plastic small outline package; 16 leads; body width 3.9 mm SOT109-1
TSA5521M SSOP16 plastic shrink small outline package; 16 leads; body width 4.4 mm SOT369-1
TSA5521T SO16 plastic small outline package; 16 leads; body width 3.9 mm SOT109-1
1996 Oct 10 2
Philips Semiconductors Product specification
1996 Oct 10 3
Philips Semiconductors Product specification
Notes
1. The selection of the reference divider is given by an automatic identification of the data word length.
2. The reference divider is set to 640 at power-on reset.
1996 Oct 10 4
Philips Semiconductors Product specification
BLOCK DIAGRAM
CP
RSA RSB
T2,T1,T0
POWER-ON
RESET 15-BIT FREQUENCY
REGISTER
IN-LOCK
DETECTOR LOGIC
13
SCL
14 LOCK
I 2 C/3-WIRE BUS
SDA RECEIVER
15 RSA,RSB
CE 3
VCC1
OS
4-BIT BAND SWITCH 7-BIT CONTROL
REGISTER GATE REGISTER 2
11 VEE
SW
T2,T1,T0
12
LOCK
TSA5520
TSA5521
4 8 7 6 5
MKA965
VCC2 BS1 BS2 BS3 BS4
1996 Oct 10 5
Philips Semiconductors Product specification
PINNING
FUNCTIONAL DESCRIPTION The first bit of the first data byte transmitted indicates
whether frequency data (first bit = 0) or control and band
The device is controlled via the I2C-bus or the 3-wire bus
switch data (first bit = 1) will follow. Until an I2C-bus STOP
depending on the voltage applied to the SW input (pin 11).
command is sent by the controller, additional data bytes
A HIGH level on the SW input enables the 3-wire bus
can be entered without the need to re-address the device.
inputs which are Chip Enable (CE), serial data input (SDA)
The frequency register is loaded after the 8th clock pulse
and serial clock input (SCL). A LOW level on the SW input
of the second Divider Byte (DB2), the control register is
enables the I2C-bus inputs which are CE [Address
loaded after the 8th clock pulse of the Control Byte (CB)
Selection (AS) input], serial data input/output (SDA) and
and the band switch register is loaded after the 8th clock
serial clock input (SCL). The bus format selection is given
pulse of the Band switch Byte (BB).
in Table 2.
I2C-bus address selection
I2C-bus mode (SW = LOW); see Table 3
The module address contains programmable address bits
Data bytes can be sent to the device after the address
(MA1 and MA0) which offer the possibility of having
transmission (first byte). Four data bytes are required to
several synthesizers (up to 3) in one system by applying a
fully program the device. The bus receiver has an
specific voltage to the CE input.
auto-increment facility which permits the programming of
the device within one single transmission The relationship between MA1 and MA0 and the input
(address + 4 data bytes). voltage applied to the CE input is given in Table 5.
The device can also be partially programmed providing
that the first data byte following the address is Divider
Byte 1 (DB1) or the Control Byte (CB). The bits in the data
bytes are defined in Table 3.
1996 Oct 10 6
Philips Semiconductors Product specification
SYMBOL DESCRIPTION
A acknowledge
MA1 and MA0 programmable address bits (see Table 5)
N14 to N0 programmable divider bits; N = N14 × 214 + N13 × 213 + ... + N1 × 2 + N0
CP charge-pump current; CP = 0 = 60 µA; CP = 1 = 280 µA
T2 to T0 test bits (see Table 6); for normal operation T2 = 0, T1 = 0 and T0 = 1
RSA and RSB reference divider ratio select bits (see Table 7)
OS tuning amplifier control bit; for normal operation OS = 0 and tuning voltage is ON;
when OS = 1 tuning voltage is OFF (high impedance)
BS4 to BS1 PNP band switch buffers control bits; when BSn = 0 buffer n is OFF;
when BSn = 1 buffer n is ON
X don’t care
1996 Oct 10 7
Philips Semiconductors Product specification
3-wire bus mode (SW = open-circuit or VCC1); occurs. Only RSA is controlled by the transmission length
see Figs 3, 4 and 5 when the 18-bit or 19-bit format is used.
During a HIGH level on the CE input, the data is clocked A data word of less than 18 bits will not affect the
into the data register at the HIGH-to-LOW transition of the frequency register of the device. The definition of the bits
clock pulse. The first four bits control the band switch is unchanged compared to the I2C bus mode.
buffers and are loaded into the internal band switch
The power-on detection threshold voltage VPOR is fixed to
register on the 5th rising edge of the clock pulse.
VCC1 = 2 V at room temperature. Below this threshold, the
The frequency bits are loaded into the frequency register
device is reset to the power-on state described above.
at the HIGH-to-LOW transition of the chip enable line when
an 18-bit or 19-bit data word is transmitted.
Table 6 Test bits
At power-on the charge-pump current is set to 280 µA, the
tuning voltage output is disabled (Vtune = 33 V in T2 T1 T0 DEVICE OPERATION
application; see Fig.12), the test bits T2, T1 and T0 are set 0 0 1 normal mode
to the normal mode and RSB is set to 1 (TSA5520) or 0 0 1 X charge-pump is OFF
(TSA5521). When an 18-bit data word is transmitted, the
1 1 0 charge-pump is sinking current
most significant bit of the divider N14 is internally set to 0
and bit RSA is set to 1. When a 19-bit data word is 1 1 1 charge-pump is sourcing current
transmitted, bit RSA is set to 0. 1 0 0 fref is available at LOCK output
1 0 1 1⁄ f is available at LOCK output
When a 27-bit word is transmitted, the frequency bits are 2 div
loaded into the frequency register on the 20th rising edge
of the clock pulse and the control bits at the HIGH-to-LOW Table 7 Ratio select bits
transition of the chip enable line. In this mode, the
RSA RSB REFERENCE DIVIDER
reference divider is given by the RSA and RSB bits (see
Table 7). The test bits T2, T1 and T0, the charge-pump X 0 640
bit CP, the ratio select bit RSB and the OS bit can only be 0 1 1024
selected or changed with a 27-bit transmission. They 1 1 512
remain programmed if an 18-bit or a 19-bit transmission
For TSA5520 bit RSB = 1 at power-on; the reference divider is 512 or 1024.
For TSA5521 bit RSB = 0 at power-on; the reference divider is 640.
For TSA5520/TSA5521 the value of RSB can also be programmed by using the 27-bit data format. When returning to the normal mode, bit RSB remains
as programmed with the 27-bit data word.
1996 Oct 10 8
Philips Semiconductors Product specification
For TSA5520 bit RSB = 1 at power-on; the reference divider is 512 or 1024.
For TSA5521 bit RSB = 0 at power-on; the reference divider is 640.
For TSA5520/TSA5521 the value of RSB can also be programmed by using the 27-bit data format. When returning to the normal mode, bit RSB remains
as programmed with the 27-bit data word.
For TSA5520 bit RSB = 1 at power-on; the reference divider is 512 or 1024.
For TSA5521 bit RSB = 0 at power-on; the reference divider is 640.
For TSA5520/TSA5521 the value of RSB can also be programmed by using the 27-bit data format. When returning to the normal mode, bit RSB remains
as programmed with the 27-bit data word.
1996 Oct 10 9
Philips Semiconductors Product specification
LIMITING VALUES
In accordance with the Absolute Maximum Rating System (IEC 134).
SYMBOL PARAMETER CONDITIONS MIN. MAX. UNIT
VCC1 supply voltage; +5 V (pin 3) −0.3 +6.0 V
VCC2 band switch supply voltage; +12 V (pin 4) −0.3 +16 V
Vi(RF) prescaler input voltage −0.3 VCC1 V
Vo(BSn) band switch buffers output voltage −0.3 VCC2 V
(pins 5 to 8)
Io(BSn) band switch buffers output current −1 +50 mA
Vo(CP) charge-pump output voltage (pin 9) −0.3 VCC1 V
Vo(tune) output tuning voltage (pin 10) −0.3 +35 V
Vi(SW) input switching voltage (pin 11) −0.3 VCC1 V
Vo(LOCK) lock output voltage (pin 12) −0.3 VCC1 V
Vi(SCL) serial clock input voltage (pin 13) −0.3 +6.0 V
Vi/o(SDA) serial data input/output voltage (pin 14) −0.3 +6.0 V
Io(SDA) serial data output current −1 +10 mA
Vi(CE) chip enable input voltage (pin 15) −0.3 +6.0 V
Vi(xtal) crystal oscillator input voltage (pin 16) −0.3 VCC1 V
Tstg IC storage temperature −40 +150 °C
Tj maximum junction temperature − +150 °C
tsc short-circuit time; every pin except pin 4 to note 1 − 10 s
pin 3 and every pin to pin 2
Note
1. Short-circuit between VCC1 and VCC2 is allowed provided the voltage applied to VCC2 is less than the 6 V maximum
rating at VCC1.
HANDLING
Inputs and outputs are protected against electrostatic discharge in normal handling. However, to be totally safe, it is
desirable to take normal precautions appropriate to handling bipolar devices. Every pin withstands the ESD test in
accordance with “MIL-STD-883C category B” (2000 V). Every pin withstands the ESD test in accordance with Philips
Semiconductors Machine Model 0 Ω, 200 pF (200 V).
THERMAL CHARACTERISTICS
1996 Oct 10 10
Philips Semiconductors Product specification
CHARACTERISTICS
VCC1 = 4.5 to 5.5 V; VCC2 = VCC1 to 13.2 V; Tamb = −20 to +85 °C; unless otherwise specified.
SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT
Supplies
VCC1 supply voltage 4.5 − 5.5 V
VCC2 band switch buffers supply VCC1 12 13.5 V
voltage
ICC1 supply current at power-on − 20 25 mA
ICC2 band switch buffers supply current at power-on − 0.5 1 mA
one band switch buffer is ON; − 50 55 mA
Isource = 40 mA
two band switch buffers are ON; − 56 62 mA
Isource = 40 mA + 5 mA
(any combination)
VPOR supply voltage below which POR 1.5 2.0 − V
is active
fRF RF input frequency 64 − 1300 MHz
DR divider ratio 15-bit frequency word 256 − 32767
14-bit frequency word 256 − 16383
fxtal crystal oscillator input frequency Rxtal = 25 to 200 Ω 3.2 4.0 4.48 MHz
Zxtal crystal oscillator input impedance fi = 4 MHz 600 1200 − Ω
(absolute value)
Prescaler (see Figs 8 and 9)
Vi(RF) RF input level fi = 80 to 150 MHz −25 − 3 dBm
fi = 150 to 1000 MHz −28 − 3 dBm
fi = 1000 to 1300 MHz −15 − 3 dBm
Zi(RF) input impedance see Fig.8
PNP band switch buffers outputs (pins 5 to 8)
ILO output leakage current VCC2 = 13.5 V; −10 − − µA
Vo = 0 V
Vo(sat) output saturation voltage Isource = 40 mA; − 0.2 0.4 V
Vo(sat) = VCC2 − Vo
LOCK output (PNP collector output)
Io(ool) output current when out-of-lock VCC1 = 5.5 V; Vo = 5.5 V − − 100 µA
Vosat(ool) output saturation voltage when Isource = 200 µA; − 0.4 0.8 V
out-of-lock Vo(sat) = VCC1 − Vo
Vo(LOCK) LOCK output voltage − 0.01 0.4 V
SW input (bus format input)
VIL LOW level input voltage 0 − 1.5 V
VIH HIGH level input voltage 3 − VCC1 V
IIH HIGH level input current VSW = VCC1 − − 10 µA
IIL LOW level input current VSW = 0 V −100 − − µA
1996 Oct 10 11
Philips Semiconductors Product specification
1996 Oct 10 12
Philips Semiconductors Product specification
Fig.6 Timing diagram for 3-wire bus; SDA, SCL and CE.
1996 Oct 10 13
Philips Semiconductors Product specification
BBBBBBBBBBBBBBBBBBBBBBBBBB
Fig.8 Prescaler Smith chart of typical input impedance at pin 1.
BBBBBBBBBBBBBBBBBBBBBBBBBB
BBBBBBBBBBBBBBBBBBBBBBBBBB
BBBBBBBBBBBBBBBBBBBBBBBBBB
BBBBBBBBBBBBBBBBBBBBBBBBBB
BBBBBBBBBBBBBBBBBBBBBBBBBB
BBBBBBBBBBBBBBBBBBBBBBBBBB
BBBBBBBBBBBBBBBBBBBBBBBBBB
BBBBBBBBBBBBBBBBBBBBBBBBBB
BBBBBBBBBBBBBBBBBBBBBBBBBB
BBBBBBBBBBBBBBBBBBBBBBBBBB
BBBBBBBBBBBBBBBBBBBBBBBBBB
BBBBBBBBBBBBBBBBBBBBBBBBBB
BBBBBBBBBBBBBBBBBBBBBBBBBB
BBBBBBBBBBBBBBBBBBBBBBBBBB
BBBBBBBBBBBBBBBBBBBBBBBBBB
BBBBBBBBBBBBBBBBBBBBBBBBBB
BBBBBBBBBBBBBBBBBBBBBBBBBB
BBBBBBBBBBBBBBBBBBBBBBBBBB
Fig.9 Prescaler typical input sensitivity curve.
1996 Oct 10 14
Philips Semiconductors Product specification
1
RF
16
XTAL
VEE VEE
VCC1
2
V EE
3 15
VCC1 CE
4
VCC2
VEE
to address
VCC2 selection
VCC1
5 14
BS4 SDA
VEE
ACK
VEE (I2 C BUS)
VCC1
VCC2
13
TSA5520 SCL
TSA5521
6
BS3 VEE
VCC1
command
12
LOCK
VEE
VCC2 VEE
VCC1
7 11
BS2
SW
VEE
10
V tune
VEE
VCC2
VEE
VCC1
8
BS1
down
9
CP
VEE
up
VEE
MLC886 - 1
1996 Oct 10 15
Philips Semiconductors Product specification
Other I2C-bus sequences are not allowed. Other I2C-bus addresses may be selected by applying an appropriate voltage
to the CE input.
The reference divider is automatically set to 512 unless RSB has been programmed to 0 during a 27-bit sequence.
1996 Oct 10 16
Philips Semiconductors Product specification
Table 15 27-bit sequence (fosc = 750 MHz, BS1 = ON, N = 640, Icp = 60 µA, no test function)
0 0 0 1 0 1 1 1 0 1 0 1 0 0 1 1 0 0 0 1 0 0 0 1 0 0 0
The reference divider is automatically set to 1024 unless RSB has been programmed to 0 during a 27-bit sequence.
This sequence sets RSA = RSB = 0; CP = 0.
This sequence will program fosc to 600 MHz in 50 kHz steps. ICP remains at 60 µA.
This sequence will program fosc to 600 MHz in 50 kHz steps. ICP remains at 60 µA.
This sequence sets RSA to 0, RSB to 1 and CP to 1. After this sequence ICP = 280 µA, N = 1024 (19-bit transmission)
and N = 512 (18-bit transmission), RSB = 1.
1996 Oct 10 17
Philips Semiconductors Product specification
22 kΩ
V tune
handbook, full pagewidth
33
27 nF
2.2 nF kΩ
33 V
100 nF
CP BS1 SWITCH
22 kΩ
V tune BS2 HIGH
SW BS3 MID
VCC1 (2)
SDA SDA 10 nF
AS CE V EE
XTAL RF RF
1 nF
5V
MLC887
(1)
4 MHz 18 pF
22 kΩ
handbook, full pagewidth V tune
33
27 nF
2.2 nF kΩ
33 V
100 nF
CP BS1 SWITCH
22 kΩ
V tune BS2 HIGH
SW BS3 MID
VCC1 (2)
DATA SDA 10 nF
ENABLE CE V EE
XTAL RF RF
1 nF
5V
MLC888
(1)
4 MHz 18 pF
1996 Oct 10 18
Philips Semiconductors Product specification
PACKAGE OUTLINES
SO16: plastic small outline package; 16 leads; body width 3.9 mm SOT109-1
D E A
X
y HE v M A
16 9
Q
A2
(A 3) A
A1
pin 1 index
θ
Lp
1 8 L
e w M detail X
bp
0 2.5 5 mm
scale
0.25 1.45 0.49 0.25 10.0 4.0 6.2 1.0 0.7 0.7
mm 1.75 0.25 1.27 1.05 0.25 0.25 0.1 o
0.10 1.25 0.36 0.19 9.8 3.8 5.8 0.4 0.6 0.3 8
0.0098 0.057 0.019 0.0098 0.39 0.16 0.24 0.039 0.028 0.028 0o
inches 0.069 0.01 0.050 0.041 0.01 0.01 0.004
0.0039 0.049 0.014 0.0075 0.38 0.15 0.23 0.016 0.020 0.012
Note
1. Plastic or metal protrusions of 0.15 mm maximum per side are not included.
91-08-13
SOT109-1 076E07S MS-012AC
95-01-23
1996 Oct 10 19
Philips Semiconductors Product specification
SSOP16: plastic shrink small outline package; 16 leads; body width 4.4 mm SOT369-1
D E A
X
y HE v M A
16 9
Q
A2 A
(A 3)
pin 1 index A1
θ
Lp
L
1 8
detail X
w M
e bp
0 2.5 5 mm
scale
Note
1. Plastic or metal protrusions of 0.20 mm maximum per side are not included.
94-04-20
SOT369-1
95-02-04
1996 Oct 10 20
Philips Semiconductors Product specification
1996 Oct 10 21
Philips Semiconductors Product specification
DEFINITIONS
Purchase of Philips I2C components conveys a license under the Philips’ I2C patent to use the
components in the I2C system provided the system conforms to the I2C specification defined by
Philips. This specification can be ordered using the code 9398 393 40011.
1996 Oct 10 22
Philips Semiconductors Product specification
NOTES
1996 Oct 10 23
Philips Semiconductors – a worldwide company
Argentina: see South America Netherlands: Postbus 90050, 5600 PB EINDHOVEN, Bldg. VB,
Australia: 34 Waterloo Road, NORTH RYDE, NSW 2113, Tel. +31 40 27 82785, Fax. +31 40 27 88399
Tel. +61 2 9805 4455, Fax. +61 2 9805 4466 New Zealand: 2 Wagener Place, C.P.O. Box 1041, AUCKLAND,
Austria: Computerstr. 6, A-1101 WIEN, P.O. Box 213, Tel. +64 9 849 4160, Fax. +64 9 849 7811
Tel. +43 1 60 101, Fax. +43 1 60 101 1210 Norway: Box 1, Manglerud 0612, OSLO,
Belarus: Hotel Minsk Business Center, Bld. 3, r. 1211, Volodarski Str. 6, Tel. +47 22 74 8000, Fax. +47 22 74 8341
220050 MINSK, Tel. +375 172 200 733, Fax. +375 172 200 773 Philippines: Philips Semiconductors Philippines Inc.,
Belgium: see The Netherlands 106 Valero St. Salcedo Village, P.O. Box 2108 MCC, MAKATI,
Metro MANILA, Tel. +63 2 816 6380, Fax. +63 2 817 3474
Brazil: see South America
Poland: Ul. Lukiska 10, PL 04-123 WARSZAWA,
Bulgaria: Philips Bulgaria Ltd., Energoproject, 15th floor, Tel. +48 22 612 2831, Fax. +48 22 612 2327
51 James Bourchier Blvd., 1407 SOFIA,
Tel. +359 2 689 211, Fax. +359 2 689 102 Portugal: see Spain
Canada: PHILIPS SEMICONDUCTORS/COMPONENTS, Romania: see Italy
Tel. +1 800 234 7381 Russia: Philips Russia, Ul. Usatcheva 35A, 119048 MOSCOW,
China/Hong Kong: 501 Hong Kong Industrial Technology Centre, Tel. +7 095 247 9145, Fax. +7 095 247 9144
72 Tat Chee Avenue, Kowloon Tong, HONG KONG, Singapore: Lorong 1, Toa Payoh, SINGAPORE 1231,
Tel. +852 2319 7888, Fax. +852 2319 7700 Tel. +65 350 2538, Fax. +65 251 6500
Colombia: see South America Slovakia: see Austria
Czech Republic: see Austria Slovenia: see Italy
Denmark: Prags Boulevard 80, PB 1919, DK-2300 COPENHAGEN S, South Africa: S.A. PHILIPS Pty Ltd., 195-215 Main Road Martindale,
Tel. +45 32 88 2636, Fax. +45 31 57 1949 2092 JOHANNESBURG, P.O. Box 7430 Johannesburg 2000,
Finland: Sinikalliontie 3, FIN-02630 ESPOO, Tel. +27 11 470 5911, Fax. +27 11 470 5494
Tel. +358 9 615800, Fax. +358 9 61580/xxx South America: Rua do Rocio 220, 5th floor, Suite 51,
France: 4 Rue du Port-aux-Vins, BP317, 92156 SURESNES Cedex, 04552-903 São Paulo, SÃO PAULO - SP, Brazil,
Tel. +33 1 40 99 6161, Fax. +33 1 40 99 6427 Tel. +55 11 821 2333, Fax. +55 11 829 1849
Germany: Hammerbrookstraße 69, D-20097 HAMBURG, Spain: Balmes 22, 08007 BARCELONA,
Tel. +49 40 23 53 60, Fax. +49 40 23 536 300 Tel. +34 3 301 6312, Fax. +34 3 301 4107
Greece: No. 15, 25th March Street, GR 17778 TAVROS/ATHENS, Sweden: Kottbygatan 7, Akalla, S-16485 STOCKHOLM,
Tel. +30 1 4894 339/239, Fax. +30 1 4814 240 Tel. +46 8 632 2000, Fax. +46 8 632 2745
Hungary: see Austria Switzerland: Allmendstrasse 140, CH-8027 ZÜRICH,
Tel. +41 1 488 2686, Fax. +41 1 481 7730
India: Philips INDIA Ltd, Shivsagar Estate, A Block, Dr. Annie Besant Rd.
Worli, MUMBAI 400 018, Tel. +91 22 4938 541, Fax. +91 22 4938 722 Taiwan: PHILIPS TAIWAN Ltd., 23-30F, 66,
Chung Hsiao West Road, Sec. 1, P.O. Box 22978,
Indonesia: see Singapore TAIPEI 100, Tel. +886 2 382 4443, Fax. +886 2 382 4444
Ireland: Newstead, Clonskeagh, DUBLIN 14, Thailand: PHILIPS ELECTRONICS (THAILAND) Ltd.,
Tel. +353 1 7640 000, Fax. +353 1 7640 200 209/2 Sanpavuth-Bangna Road Prakanong, BANGKOK 10260,
Israel: RAPAC Electronics, 7 Kehilat Saloniki St, TEL AVIV 61180, Tel. +66 2 745 4090, Fax. +66 2 398 0793
Tel. +972 3 645 0444, Fax. +972 3 649 1007 Turkey: Talatpasa Cad. No. 5, 80640 GÜLTEPE/ISTANBUL,
Italy: PHILIPS SEMICONDUCTORS, Piazza IV Novembre 3, Tel. +90 212 279 2770, Fax. +90 212 282 6707
20124 MILANO, Tel. +39 2 6752 2531, Fax. +39 2 6752 2557 Ukraine: PHILIPS UKRAINE, 4 Patrice Lumumba str., Building B, Floor 7,
Japan: Philips Bldg 13-37, Kohnan 2-chome, Minato-ku, TOKYO 108, 252042 KIEV, Tel. +380 44 264 2776, Fax. +380 44 268 0461
Tel. +81 3 3740 5130, Fax. +81 3 3740 5077 United Kingdom: Philips Semiconductors Ltd., 276 Bath Road, Hayes,
Korea: Philips House, 260-199 Itaewon-dong, Yongsan-ku, SEOUL, MIDDLESEX UB3 5BX, Tel. +44 181 730 5000, Fax. +44 181 754 8421
Tel. +82 2 709 1412, Fax. +82 2 709 1415 United States: 811 East Arques Avenue, SUNNYVALE, CA 94088-3409,
Malaysia: No. 76 Jalan Universiti, 46200 PETALING JAYA, SELANGOR, Tel. +1 800 234 7381
Tel. +60 3 750 5214, Fax. +60 3 757 4880 Uruguay: see South America
Mexico: 5900 Gateway East, Suite 200, EL PASO, TEXAS 79905, Vietnam: see Singapore
Tel. +9-5 800 234 7381
Yugoslavia: PHILIPS, Trg N. Pasica 5/v, 11000 BEOGRAD,
Middle East: see Italy Tel. +381 11 625 344, Fax.+381 11 635 777
For all other countries apply to: Philips Semiconductors, Marketing & Sales Communications, Internet: http://www.semiconductors.philips.com
Building BE-p, P.O. Box 218, 5600 MD EINDHOVEN, The Netherlands, Fax. +31 40 27 24825
Printed in The Netherlands 537021/50/02/pp24 Date of release: 1996 Oct 10 Document order number: 9397 750 01353